From: Yuugo Yoneda via B4 Relay <devnull+yogo.0917.sabu.gmail.com@kernel.org>
To: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Thomas Gleixner <tglx@kernel.org>, Radu Rendec <radu@rendec.net>,
Daniel Lezcano <daniel.lezcano@kernel.org>,
Dmitry Torokhov <dmitry.torokhov@gmail.com>,
Ulf Hansson <ulfh@kernel.org>,
Adrian Hunter <adrian.hunter@intel.com>,
Jonathan Corbet <corbet@lwn.net>,
Shuah Khan <skhan@linuxfoundation.org>,
Randy Dunlap <rdunlap@infradead.org>,
Russell King <linux@armlinux.org.uk>,
Arnd Bergmann <arnd@arndb.de>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Linus Walleij <linusw@kernel.org>,
Drew Fustini <fustini@kernel.org>,
linux-kernel@vger.kernel.org, linux-input@vger.kernel.org,
linux-mmc@vger.kernel.org, linux-doc@vger.kernel.org,
soc@lists.linux.dev
Subject: [PATCH RFC v2 00/13] SiRF AT550 / YPL514si initial RAM-boot platform support
Date: Sat, 21 Nov 2026 21:43:10 +0900 [thread overview]
Message-ID: <20261121-at550-rfc-v1-v2-0-b0309d0789b2@gmail.com> (raw)
This RFC adds initial platform support for the SiRF AT550 SoC
(ARM1136 r1p5, MIDR 0x4117b365) and the Yupiteru YPL514si portable
navigation device on top of 7.4-rc3.
The platform boots from RAM via a Windows CE bootloader trampoline using
standard IRQCHIP_DECLARE, TIMER_OF_DECLARE, common clock, polled input,
SDHCI PIO, and simplefb paths. Firmware initializes SDRAM, peripheral
clocks, pin multiplexing, and the LCD before handoff. The bootloader
supplies the Linux-owned RAM range in memory@c0000000 and the
post-divider counter rate in clock-counter, reserves the framebuffer
via a no-map reserved-memory node, and enables only handed-over
peripherals.
Validation status:
- Hardware: I booted both v1 and this v2 series on the YPL514si
(v2 CE handoff log confirmed a 32 MiB Linux allocation at 0xc1e00000,
8192 PFNs, 124805090 Hz measured counter clock, and all three gated
peripherals enabled).
- Local builds/checks for v2: at550_defconfig Image and DTB build (W=1),
leaf drivers built in-kernel and as modules (W=1), multiplatform
CONFIG_SMP=y + CONFIG_ARCH_AT550=y object builds (W=1),
dt_binding_check, scoped dtbs_check, dt-check-style --mode strict,
ARM32 bootloader DT fixup tests for 16/24/32 MiB, and b4 prep --check.
(QEMU ARM1136 bring-up tests were run on v1 using GIC/SP804/PL181 and
synthetic uinput rather than physical AT550 hardware.)
Initial limits:
- Peripheral clock tree control, pinctrl, cold boot, SDHCI DMA
translation, and suspend/resume are not implemented yet.
- The board DTS restricts SD to 25 MHz PIO, 3.3 V only, no MMC, and no
SDIO; SD writes and card removal are untested.
- Register layouts were cross-checked against a third-party AT551 draft
datasheet and observed CE mappings, which is not a complete AT550
hardware specification.
I would appreciate early feedback on the overall platform split and the
firmware/DT handoff contract before extending clock, pinctrl, or DMA
support.
Signed-off-by: Yuugo Yoneda <yogo.0917.sabu@gmail.com>
---
Changes in v2:
- Use my real name (Yuugo Yoneda) in author headers, MAINTAINERS, DT
binding maintainers, and Signed-off-by trailers.
- Split the monolithic bindings and platform patches into 13 commits
following subsystem and SoC conventions, and rewrite commit logs and
cover letter directly.
- Select CPU_ARM1136R1 instead of CPU_V6 in arch/arm/mach-at550/Kconfig
(also avoiding !SMP conflicts in multiplatform builds), and disable
CONFIG_ARCH_MULTI_V7 in at550_defconfig.
- Replace /memreserve/ with a /reserved-memory node using no-map in
at550-ypl514si.dts so simplefb ioremap_wc() does not alias the ARM
linear mapping.
- Update DT schemas to describe hardware instead of driver/firmware
limits (allow optional interrupts/clocks in sirf,at550-ts.yaml and
optional clocks in sirf,at550-sdhci.yaml, drop no-1-8-v from required
in sirf,at550-sdhci.yaml, allow 1..6 match interrupts and maxItems: 1
clock in sirf,at550-timer.yaml, and revise schema descriptions).
- Set IRQ_LEVEL on mapped level interrupts in irq-at550.c.
- Enable the timer clock before MMIO reads, disable the timer before
reading/updating MATCH0, clear STATUS after writing MATCH0, and
implement set_state_oneshot_stopped in timer-at550.c.
- Explicitly stop acquisition in at550_ts_close(), clear interrupts
after mode changes, include mod_devicetable.h and bits.h (dropping
unused bitfield.h), follow Input error-handling conventions, and fix
coding style in at550-ts.c.
- Drop redundant ops/remove wrappers and premature caps/version checks,
and include mod_devicetable.h in sdhci-at550.c.
- Sort subdir-y += sirf alphabetically with a trailing newline in
arch/arm/boot/dts/Makefile, and fix strict dt-check-style node/property
ordering and blank lines in at550.dtsi and at550-ypl514si.dts.
- Link to v1: https://patch.msgid.link/20261117-at550-rfc-v1-v1-0-5879573cb825@gmail.com
---
Yuugo Yoneda (13):
dt-bindings: vendor-prefixes: add Yupiteru
dt-bindings: arm: add SiRF AT550 and Yupiteru YPL514si
dt-bindings: interrupt-controller: add SiRF AT550 interrupt controller
irqchip: add SiRF AT550 interrupt controller driver
dt-bindings: timer: add SiRF AT550 system timer
clocksource/drivers/timer-at550: add SiRF AT550 counter and match timer
dt-bindings: input: touchscreen: add SiRF AT550 touchscreen
Input: add polled SiRF AT550 resistive touchscreen driver
dt-bindings: mmc: add SiRF AT550 SDHCI host controller
mmc: sdhci-at550: add SiRF AT550 programmed-I/O host driver
ARM: at550: add SiRF AT550 platform support
ARM: dts: sirf: add SiRF AT550 SoC and Yupiteru YPL514si board
ARM: configs: add at550_defconfig
Documentation/arch/arm/at550.rst | 56 +++++++++
Documentation/arch/arm/index.rst | 1 +
.../devicetree/bindings/arm/sirf,at550.yaml | 22 ++++
.../bindings/input/touchscreen/sirf,at550-ts.yaml | 40 ++++++
.../interrupt-controller/sirf,at550-intc.yaml | 46 +++++++
.../devicetree/bindings/mmc/sirf,at550-sdhci.yaml | 50 ++++++++
.../bindings/timer/sirf,at550-timer.yaml | 51 ++++++++
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 17 +++
arch/arm/Kconfig | 1 +
arch/arm/Makefile | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sirf/Makefile | 2 +
arch/arm/boot/dts/sirf/at550-ypl514si.dts | 63 ++++++++++
arch/arm/boot/dts/sirf/at550.dtsi | 69 +++++++++++
arch/arm/configs/at550_defconfig | 35 ++++++
arch/arm/mach-at550/Kconfig | 13 ++
arch/arm/mach-at550/Makefile | 2 +
arch/arm/mach-at550/at550.c | 11 ++
drivers/clocksource/Kconfig | 6 +
drivers/clocksource/Makefile | 2 +
drivers/clocksource/timer-at550.c | 136 +++++++++++++++++++++
drivers/input/touchscreen/Kconfig | 10 ++
drivers/input/touchscreen/Makefile | 2 +
drivers/input/touchscreen/at550-ts.c | 124 +++++++++++++++++++
drivers/irqchip/Kconfig | 5 +
drivers/irqchip/Makefile | 2 +
drivers/irqchip/irq-at550.c | 111 +++++++++++++++++
drivers/mmc/host/Kconfig | 10 ++
drivers/mmc/host/Makefile | 2 +
drivers/mmc/host/sdhci-at550.c | 51 ++++++++
31 files changed, 944 insertions(+)
---
base-commit: 666539eecdf4db623f5e3c3e55cf9f2dfad24aa4
change-id: 20261117-at550-rfc-v1-2591185a2fe8
Best regards,
--
Yuugo Yoneda <yogo.0917.sabu@gmail.com>
next reply other threads:[~2026-11-21 12:43 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-21 12:43 Yuugo Yoneda via B4 Relay [this message]
2026-11-21 12:43 ` [PATCH RFC v2 01/13] dt-bindings: vendor-prefixes: add Yupiteru Yuugo Yoneda via B4 Relay
2026-11-21 12:43 ` [PATCH RFC v2 02/13] dt-bindings: arm: add SiRF AT550 and Yupiteru YPL514si Yuugo Yoneda via B4 Relay
2026-11-21 12:43 ` [PATCH RFC v2 03/13] dt-bindings: interrupt-controller: add SiRF AT550 interrupt controller Yuugo Yoneda via B4 Relay
2026-11-21 12:43 ` [PATCH RFC v2 04/13] irqchip: add SiRF AT550 interrupt controller driver Yuugo Yoneda via B4 Relay
2026-11-21 12:43 ` [PATCH RFC v2 05/13] dt-bindings: timer: add SiRF AT550 system timer Yuugo Yoneda via B4 Relay
2026-11-21 12:48 ` sashiko-bot
2026-11-21 12:43 ` [PATCH RFC v2 06/13] clocksource/drivers/timer-at550: add SiRF AT550 counter and match timer Yuugo Yoneda via B4 Relay
2026-11-21 12:43 ` [PATCH RFC v2 07/13] dt-bindings: input: touchscreen: add SiRF AT550 touchscreen Yuugo Yoneda via B4 Relay
2026-11-21 12:48 ` sashiko-bot
2026-11-21 12:43 ` [PATCH RFC v2 08/13] Input: add polled SiRF AT550 resistive touchscreen driver Yuugo Yoneda via B4 Relay
2026-11-21 12:43 ` [PATCH RFC v2 09/13] dt-bindings: mmc: add SiRF AT550 SDHCI host controller Yuugo Yoneda via B4 Relay
2026-11-21 12:48 ` sashiko-bot
2026-11-21 12:43 ` [PATCH RFC v2 10/13] mmc: sdhci-at550: add SiRF AT550 programmed-I/O host driver Yuugo Yoneda via B4 Relay
2026-11-21 12:43 ` [PATCH RFC v2 11/13] ARM: at550: add SiRF AT550 platform support Yuugo Yoneda via B4 Relay
2026-11-21 12:43 ` [PATCH RFC v2 12/13] ARM: dts: sirf: add SiRF AT550 SoC and Yupiteru YPL514si board Yuugo Yoneda via B4 Relay
2026-11-21 12:43 ` [PATCH RFC v2 13/13] ARM: configs: add at550_defconfig Yuugo Yoneda via B4 Relay
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261121-at550-rfc-v1-v2-0-b0309d0789b2@gmail.com \
--to=devnull+yogo.0917.sabu.gmail.com@kernel.org \
--cc=adrian.hunter@intel.com \
--cc=alexandre.belloni@bootlin.com \
--cc=arnd@arndb.de \
--cc=conor+dt@kernel.org \
--cc=corbet@lwn.net \
--cc=daniel.lezcano@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.torokhov@gmail.com \
--cc=fustini@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linusw@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=radu@rendec.net \
--cc=rdunlap@infradead.org \
--cc=robh@kernel.org \
--cc=skhan@linuxfoundation.org \
--cc=soc@lists.linux.dev \
--cc=tglx@kernel.org \
--cc=ulfh@kernel.org \
--cc=yogo.0917.sabu@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox