* [linux-dvb] Firmware for HVR-1110 @ 2010-07-03 2:21 JD 2010-07-03 2:32 ` Fwd: " JD 0 siblings, 1 reply; 6+ messages in thread From: JD @ 2010-07-03 2:21 UTC (permalink / raw) To: linux-dvb [-- Attachment #1.1: Type: text/plain, Size: 327 bytes --] What firmware in needed for the HVR-1110, as I am unable to find any channels? Scouring the web claims that the dvb-fe-tda10046 is required; however, dmesg logs show that this fails to be uploaded. If I use the dvb-fe-tda-10048-1.0.fw, dmesg seems to successfully load this firmware, but I still can't find any singal. Thanks [-- Attachment #1.2: Type: text/html, Size: 350 bytes --] [-- Attachment #2: Type: text/plain, Size: 228 bytes --] _______________________________________________ linux-dvb users mailing list For V4L/DVB development, please use instead linux-media@vger.kernel.org linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Fwd: Firmware for HVR-1110 2010-07-03 2:21 [linux-dvb] Firmware for HVR-1110 JD @ 2010-07-03 2:32 ` JD 2010-07-04 3:13 ` hermann pitton 0 siblings, 1 reply; 6+ messages in thread From: JD @ 2010-07-03 2:32 UTC (permalink / raw) To: linux-media I'm confused as to what firmware in needed for the HVR-1110. Scouring the web, everywhere claims that the dvb-fe-tda10046 is required; however, dmesg logs show that this fails to be uploaded, and instead it is looking for dvb-fe-tda-10048: If I use tda-10048 then this seems to successfully loaded, but I am unable to find any channels with a scan; the dvb nodes within /dev/ are created and modules loaded, but dvbscan fails to tune. ------ dmesg -------- $ dmesg |grep firmware tda10048_firmware_upload: waiting for firmware upload (dvb-fe-tda10048-1.0.fw)... saa7134 0000:03:04.0: firmware: requesting dvb-fe-tda10048-1.0.fw tda10048_firmware_upload: firmware read 24878 bytes. tda10048_firmware_upload: firmware uploading tda10048_firmware_upload: firmware uploaded Any tips? Thanks. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Fwd: Firmware for HVR-1110 2010-07-03 2:32 ` Fwd: " JD @ 2010-07-04 3:13 ` hermann pitton 2010-07-05 13:10 ` JD 0 siblings, 1 reply; 6+ messages in thread From: hermann pitton @ 2010-07-04 3:13 UTC (permalink / raw) To: JD; +Cc: linux-media Hi JD, Am Samstag, den 03.07.2010, 03:32 +0100 schrieb JD: > I'm confused as to what firmware in needed for the HVR-1110. > > Scouring the web, everywhere claims that the dvb-fe-tda10046 is > required; however, dmesg logs show that this fails to be uploaded, and > instead it is looking for dvb-fe-tda-10048: > > If I use tda-10048 then this seems to successfully loaded, but I am > unable to find any channels with a scan; the dvb nodes within /dev/ > are created and modules loaded, but dvbscan fails to tune. > > ------ > dmesg > -------- > $ dmesg |grep firmware > tda10048_firmware_upload: waiting for firmware upload > (dvb-fe-tda10048-1.0.fw)... > saa7134 0000:03:04.0: firmware: requesting dvb-fe-tda10048-1.0.fw > tda10048_firmware_upload: firmware read 24878 bytes. > tda10048_firmware_upload: firmware uploading > tda10048_firmware_upload: firmware uploaded > > Any tips? > Thanks. > -- all variants of the HVR-1110 have a tda 10046. I can't see, how firmware loading can fail on auto detection of those and even switch over to tda10048 as an alternative. Do you force some card = number and are maybe on a not yet detected HVR-1120? Please provide the full dmesg log related to your card and make sure you are on Michael Krufky's latest patches. Cheers, Hermann ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Fwd: Firmware for HVR-1110 2010-07-04 3:13 ` hermann pitton @ 2010-07-05 13:10 ` JD 2010-07-05 19:08 ` JD 0 siblings, 1 reply; 6+ messages in thread From: JD @ 2010-07-05 13:10 UTC (permalink / raw) To: linux-media hermann pitton <hermann-pitton <at> arcor.de> writes: > > Hi JD,http://pastebin.ca/1894929 > > Am Samstag, den 03.07.2010, 03:32 +0100 schrieb JD: > > I'm confused as to what firmware in needed for the HVR-1110. > > > > Scouring the web, everywhere claims that the dvb-fe-tda10046 is > > required; however, dmesg logs show that this fails to be uploaded, and > > instead it is looking for dvb-fe-tda-10048: > > > > If I use tda-10048 then this seems to successfully loaded, but I am > > unable to find any channels with a scan; the dvb nodes within /dev/ > > are created and modules loaded, but dvbscan fails to tune. > > > > ------ > > dmesg > > -------- > > $ dmesg |grep firmware > > tda10048_firmware_upload: waiting for firmware upload > > (dvb-fe-tda10048-1.0.fw)... > > saa7134 0000:03:04.0: firmware: requesting dvb-fe-tda10048-1.0.fw > > tda10048_firmware_upload: firmware read 24878 bytes. > > tda10048_firmware_upload: firmware uploading > > tda10048_firmware_upload: firmware uploaded > > > > Any tips? > > Thanks. > > -- > > all variants of the HVR-1110 have a tda 10046. > > I can't see, how firmware loading can fail on auto detection of those > and even switch over to tda10048 as an alternative. > > Do you force some card = number and are maybe on a not yet detected > HVR-1120? > > Please provide the full dmesg log related to your card and make sure you > are on Michael Krufky's latest patches. > > Cheers, > Hermann > > Hi, thanks for the reply. To be sure that I hadn't set a certain card type somewhere, I used a clean install of a different OS (Linux Mint on a live USB); however, dmesg still shows that for some reason it is looking for the tda-10048 firmware. Here's the dmesg output: http://pastebin.ca/1894693 Here's the dmesg out after installing the tda10048 firmware if it is any help: http://pastebin.ca/1894929 I am able to find two or three analogue channels with tvtime, but no digital channels at all: dvbscan always says "tuning failed", and using vlc to search for dvb-t channels results in none. I do not have the patches you mention, as I am quite new to tv for linux, but I'll take a look shortly. My card is definitely the WinTV-HVR1110 as it states it on the card itself, but the packaging states HVR-1110. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Fwd: Firmware for HVR-1110 2010-07-05 13:10 ` JD @ 2010-07-05 19:08 ` JD 2010-07-05 21:27 ` hermann pitton 0 siblings, 1 reply; 6+ messages in thread From: JD @ 2010-07-05 19:08 UTC (permalink / raw) To: linux-media > All seems to be working fine now, I followed the installtion guide for the HVR-1120 and used the tda10048 f/w and I can now find DVB channels; I am still not sure as to why my card is looking for a different f/w tho, and would like to know why if anyone finds out. Thanks for your help. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Fwd: Firmware for HVR-1110 2010-07-05 19:08 ` JD @ 2010-07-05 21:27 ` hermann pitton 0 siblings, 0 replies; 6+ messages in thread From: hermann pitton @ 2010-07-05 21:27 UTC (permalink / raw) To: JD; +Cc: linux-media Hi, JD, Am Montag, den 05.07.2010, 19:08 +0000 schrieb JD: > > > > All seems to be working fine now, I followed the installtion guide for the > HVR-1120 and used the tda10048 f/w and I can now find DVB channels; I am still > not sure as to why my card is looking for a different f/w tho, and would like to > know why if anyone finds out. > > Thanks for your help. > can't see the problem with different firmware in your logs. I guess the root cause for all your prior trouble was that the HVR 1120 is packed as a HVR1110. Such unfortunately is a known problem with new Hauppauge products since a decade :( That flaw is compensated by best auto detection and open eeprom content. Also guys like Steven and Michael did develop the drivers you need on that new card during their free time. (demodulator is in serial TS mode and new tuner on saa7134) All auto detection looks OK and of course also correct firmware is uploaded then. Especially the C2 tuner variant is still quite new and I guess Michael would prefer reports based on code on development level. Cheers, Hermann [ 12.185935] saa7130/34: v4l2 driver version 0.2.15 loaded [ 12.185990] saa7134 0000:03:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 12.185997] saa7133[0]: found at 0000:03:04.0, rev: 209, irq: 16, latency: 64, mmio: 0xfebff800 [ 12.186004] saa7133[0]: subsystem: 0070:6707, board: Hauppauge WinTV-HVR1120 DVB-T/Hybrid [card=156,autodetected] [ 12.186027] saa7133[0]: board init: gpio is 40000 [ 12.208619] IRQ 16/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 12.222966] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 12.223016] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 12.292676] hda_codec: ALC662 rev1: BIOS auto-probing. [ 12.294322] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6 [ 12.360024] saa7133[0]: i2c eeprom 00: 70 00 07 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 [ 12.360044] saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff [ 12.360062] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 b0 ff ff ff ff [ 12.360080] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 12.360097] saa7133[0]: i2c eeprom 40: ff 35 00 c0 96 10 06 32 97 04 00 20 00 ff ff ff [ 12.360114] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 12.360131] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 12.360149] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 12.360166] saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 ba 54 5e f0 73 05 29 00 [ 12.360183] saa7133[0]: i2c eeprom 90: 84 08 00 06 89 06 01 00 95 19 8d 72 07 70 73 09 [ 12.360201] saa7133[0]: i2c eeprom a0: 23 5f 73 0a f4 9b 72 0b 2f 72 0e 01 72 0f 01 72 [ 12.360215] saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 73 13 a2 69 79 8d 00 00 00 00 00 [ 12.360224] saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 12.360233] saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 12.360241] saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 12.360250] saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 12.360260] i2c i2c-1: Invalid 7-bit address 0x7a [ 12.360745] tveeprom 1-0050: Hauppauge model 67209, rev C1F5, serial# 6182074 [ 12.360748] tveeprom 1-0050: MAC address is 00-0D-FE-5E-54-BA [ 12.360750] tveeprom 1-0050: tuner model is NXP 18271C2 (idx 155, type 54) [ 12.360753] tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) [ 12.360755] tveeprom 1-0050: audio processor is SAA7131 (idx 41) [ 12.360757] tveeprom 1-0050: decoder processor is SAA7131 (idx 35) [ 12.360759] tveeprom 1-0050: has radio, has IR receiver, has no IR transmitter [ 12.360761] saa7133[0]: hauppauge eeprom: model=67209 [ 12.628148] tuner 1-004b: chip found @ 0x96 (saa7133[0]) [ 12.695985] r8169: eth0: link up [ 12.695992] r8169: eth0: link up [ 12.708063] tda829x 1-004b: setting tuner address to 60 [ 12.954972] tda18271 1-0060: creating new instance [ 13.000021] TDA18271HD/C2 detected @ 1-0060 [ 14.458202] CPU0 attaching NULL sched-domain. [ 14.458209] CPU1 attaching NULL sched-domain. [ 14.480104] CPU0 attaching sched-domain: [ 14.480108] domain 0: span 0-1 level MC [ 14.480110] groups: 0 1 [ 14.480116] CPU1 attaching sched-domain: [ 14.480118] domain 0: span 0-1 level MC [ 14.480120] groups: 1 0 [ 14.520030] tda18271: performing RF tracking filter calibration [ 15.810914] CPU0 attaching NULL sched-domain. [ 15.810921] CPU1 attaching NULL sched-domain. [ 15.832110] CPU0 attaching sched-domain: [ 15.832114] domain 0: span 0-1 level MC [ 15.832117] groups: 0 1 [ 15.832122] CPU1 attaching sched-domain: [ 15.832124] domain 0: span 0-1 level MC [ 15.832126] groups: 1 0 [ 23.436017] eth0: no IPv6 routers present [ 32.908024] tda18271: RF tracking filter calibration complete [ 32.964027] tda829x 1-004b: type set to tda8290+18271 [ 37.940216] saa7133[0]: registered device video0 [v4l2] [ 37.940278] saa7133[0]: registered device vbi0 [ 37.940335] saa7133[0]: registered device radio0 [ 37.955306] saa7134 ALSA driver for DMA sound loaded [ 37.955319] IRQ 16/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 37.955342] saa7133[0]/alsa: saa7133[0] at 0xfebff800 irq 16 registered as card -2 [ 37.996093] dvb_init() allocating 1 frontend [ 38.112029] tda829x 1-004b: type set to tda8290 [ 38.128160] tda18271 1-0060: attaching existing instance [ 38.128166] DVB: registering new adapter (saa7133[0]) [ 38.128172] DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)... [ 38.456026] tda10048_firmware_upload: waiting for firmware upload (dvb-fe-tda10048-1.0.fw)... [ 38.456034] saa7134 0000:03:04.0: firmware: requesting dvb-fe-tda10048-1.0.fw [ 38.478776] tda10048_firmware_upload: firmware read 24878 bytes. [ 38.478780] tda10048_firmware_upload: firmware uploading [ 42.600036] tda10048_firmware_upload: firmware uploaded [ 44.720534] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5 [ 44.720542] tda18271c2_rf_tracking_filters_correction: error -5 on line 264 [ 46.012535] tda18271_write_regs: ERROR: idx = 0x13, len = 1, i2c_transfer returned: -5 [ 47.048045] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5 [ 47.048056] tda18271_set_analog_params: error -5 on line 1041 ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2010-07-05 21:28 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2010-07-03 2:21 [linux-dvb] Firmware for HVR-1110 JD 2010-07-03 2:32 ` Fwd: " JD 2010-07-04 3:13 ` hermann pitton 2010-07-05 13:10 ` JD 2010-07-05 19:08 ` JD 2010-07-05 21:27 ` hermann pitton
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox