From: Sakari Ailus <sakari.ailus@linux.intel.com>
To: linux-media@vger.kernel.org
Cc: laurent.pinchart@ideasonboard.com,
Dave Stevenson <dave.stevenson@raspberrypi.com>,
Jacopo Mondi <jacopo.mondi@ideasonboard.com>,
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>,
Jai Luthra <jai.luthra@ideasonboard.com>,
Mehdi Djait <mehdi.djait@linux.intel.com>,
Frank Li <Frank.li@nxp.com>
Subject: [PATCH v2 09/17] media: bcm2835-unicam: Use v4l2_subdev_get_frame_desc()
Date: Mon, 18 May 2026 19:43:09 +0300 [thread overview]
Message-ID: <20260518164318.3367888-10-sakari.ailus@linux.intel.com> (raw)
In-Reply-To: <20260518164318.3367888-1-sakari.ailus@linux.intel.com>
Call v4l2_subdev_get_frame_desc() to obtain the frame descriptor. This is
preferred over calling the get_frame_desc() pad operation directly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
---
.../media/platform/broadcom/bcm2835-unicam.c | 22 +++++++++----------
1 file changed, 10 insertions(+), 12 deletions(-)
diff --git a/drivers/media/platform/broadcom/bcm2835-unicam.c b/drivers/media/platform/broadcom/bcm2835-unicam.c
index 8d28ba0b59a3..7e299ebf3470 100644
--- a/drivers/media/platform/broadcom/bcm2835-unicam.c
+++ b/drivers/media/platform/broadcom/bcm2835-unicam.c
@@ -27,6 +27,7 @@
* output interface and V4L2 subdevice driver.
*/
+#include <linux/cleanup.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/device.h>
@@ -888,7 +889,6 @@ static int unicam_get_image_vc_dt(struct unicam_device *unicam,
struct v4l2_subdev_state *state,
u8 *vc, u8 *dt)
{
- struct v4l2_mbus_frame_desc fd;
u32 stream;
int ret;
@@ -898,17 +898,15 @@ static int unicam_get_image_vc_dt(struct unicam_device *unicam,
if (ret)
return ret;
- ret = v4l2_subdev_call(unicam->sensor.subdev, pad, get_frame_desc,
- unicam->sensor.pad->index, &fd);
- if (ret)
- return ret;
-
- /* Only CSI-2 supports DTs. */
- if (fd.type != V4L2_MBUS_FRAME_DESC_TYPE_CSI2)
- return -EINVAL;
+ struct v4l2_mbus_frame_desc *fd __free(v4l2_subdev_free_frame_desc) =
+ v4l2_subdev_get_frame_desc(unicam->sensor.subdev,
+ unicam->sensor.pad->index,
+ V4L2_MBUS_FRAME_DESC_TYPE_CSI2);
+ if (IS_ERR(fd))
+ return PTR_ERR(fd);
- for (unsigned int i = 0; i < fd.num_entries; ++i) {
- const struct v4l2_mbus_frame_desc_entry *fde = &fd.entry[i];
+ for (unsigned int i = 0; i < fd->num_entries; ++i) {
+ const struct v4l2_mbus_frame_desc_entry *fde = &fd->entry[i];
if (fde->stream == stream) {
*vc = fde->bus.csi2.vc;
@@ -927,7 +925,7 @@ static void unicam_start_rx(struct unicam_device *unicam,
const struct unicam_format_info *fmtinfo;
const struct v4l2_mbus_framefmt *fmt;
unsigned int line_int_freq;
- u8 vc, dt;
+ u8 vc = 0, dt = 0;
u32 val;
int ret;
--
2.47.3
next prev parent reply other threads:[~2026-05-18 16:43 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-18 16:43 [PATCH v2 00/17] Rework frame descriptors Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 01/17] media: v4l2-common: Add helper function media_bus_fmt_to_csi2_(bpp|dt)() Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 02/17] media: v4l2-subdev: Align frame descriptor error codes with routing Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 03/17] media: v4l2-subdev: Prepare for changes in getting frame descriptors Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 04/17] media: v4l2-subdev: Allow releasing frame descriptors on return Sakari Ailus
2026-05-19 21:34 ` Frank Li
2026-05-20 12:56 ` Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 05/17] media: v4l2-subdev: Allocate frame descriptors based on the need Sakari Ailus
2026-05-19 21:53 ` Frank Li
2026-05-19 22:18 ` Frank Li
2026-05-18 16:43 ` [PATCH v2 06/17] media: v4l2-subdev: Change the maximum number of routes Sakari Ailus
2026-05-19 21:55 ` Frank Li
2026-05-18 16:43 ` [PATCH v2 07/17] media: v4l2-subdev: Return dynamically allocated pass-through routes Sakari Ailus
2026-05-19 22:33 ` Frank Li
2026-05-20 12:59 ` Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 08/17] media: v4l2-subdev: Always return at least one frame descriptor Sakari Ailus
2026-05-19 22:35 ` Frank Li
2026-05-18 16:43 ` Sakari Ailus [this message]
2026-05-18 16:43 ` [PATCH v2 10/17] media: nxp: imx8-isi: Use v4l2_subdev_get_frame_desc() Sakari Ailus
2026-05-19 22:36 ` Frank Li
2026-05-18 16:43 ` [PATCH v2 11/17] media: raspberrypi: cfe: " Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 12/17] media: rzg2l-cru: " Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 13/17] media: rkisp1: " Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 14/17] media: exynos4-is: " Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 15/17] media: ti: cal: " Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 16/17] media: ipu6: " Sakari Ailus
2026-05-18 16:43 ` [PATCH v2 17/17] staging: media: ipu7: " Sakari Ailus
2026-06-11 12:49 ` [PATCH v2 00/17] Rework frame descriptors Tomi Valkeinen
2026-06-12 8:28 ` Sakari Ailus
2026-06-23 7:39 ` Sakari Ailus
2026-08-14 8:17 ` Mattijs Korpershoek
2026-08-14 8:21 ` Tomi Valkeinen
2026-08-14 9:26 ` Mattijs Korpershoek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260518164318.3367888-10-sakari.ailus@linux.intel.com \
--to=sakari.ailus@linux.intel.com \
--cc=Frank.li@nxp.com \
--cc=dave.stevenson@raspberrypi.com \
--cc=jacopo.mondi@ideasonboard.com \
--cc=jai.luthra@ideasonboard.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=mehdi.djait@linux.intel.com \
--cc=tomi.valkeinen@ideasonboard.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox