Linux Media Controller development
 help / color / mirror / Atom feed
* Problem setting up HVR-1110
@ 2008-12-31 10:36 Simon Hobson
  2008-12-31 13:43 ` Simon Hobson
  0 siblings, 1 reply; 5+ messages in thread
From: Simon Hobson @ 2008-12-31 10:36 UTC (permalink / raw)
  To: video4linux-list

I've got MythTV installed and bought a Hauppage HVR-1110 card for it. 
The card is detected and the saa7134 driver loaded - but that seems 
to be it. Everything I can find suggests that the card should be 
identified automatically (and the TDA1004X driver & firmware loaded), 
but it isn't.

What I get in dmesg is :

>saa7130/34: v4l2 driver version 0.2.14 loaded
>PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
>saa7133[0]: found at 0000:00:00.0, rev: 209, irq: 17, latency: 32, 
>mmio: 0xf4100000
>saa7133[0]: subsystem: 0070:6701, board: UNKNOWN/GENERIC [card=0,autodetected]
>saa7133[0]: board init: gpio is 6400000
>saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
>saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
>saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 aa ff ff ff ff
>saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
>saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>saa7133[0]: registered device video0 [v4l2]
>saa7133[0]: registered device vbi0

and nothing at all about tda devices.

This doesn't change (apart from two lines referring to the ALSA 
driver) when I add a config file containing :
>install saa7134 /sbin/modprobe  --ignore-install saa7134 && { 
>/sbin/modprobe saa7134-alsa; } && { /sbin/modprobe saa7134-dvb;}
>options saa7134 card=104
to /etc/modprobe.d

uname -a reports :
>Linux eddi 2.6.18-6-xen-amd64 #1 SMP Fri Dec 12 07:02:03 UTC 2008 
>x86_64 GNU/Linux


Yes, this is running in a Xen guest - but I've also tried booting the 
machine into a non-Xen mode (with non-Xen kernel) and it behaves 
exactly the same. In both cases, the OS is Debian Lenny.

lspci says :
>00:00.0 Multimedia controller: Philips Semiconductors 
>SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1)

lsmod | grep 'tda
>  saa' says :

>saa7134_dvb            19460  0
>dvb_pll                20612  1 saa7134_dvb
>mt352                  11780  1 saa7134_dvb
>video_buf_dvb          11396  1 saa7134_dvb
>nxt200x                18308  1 saa7134_dvb
>tda1004x               20100  1 saa7134_dvb
>firmware_class         15616  3 saa7134_dvb,nxt200x,tda1004x
>saa7134_alsa           18912  0
>snd_pcm                89352  2 saa7134_alsa,snd_pcm_oss
>snd                    65384  8 
>saa7134_alsa,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_seq_oss,snd_seq,snd_timer,snd_seq_device
>saa7134               130408  2 saa7134_dvb,saa7134_alsa
>video_buf              31108  4 saa7134_dvb,video_buf_dvb,saa7134_alsa,saa7134
>compat_ioctl32         13184  1 saa7134
>ir_kbd_i2c             14608  1 saa7134
>i2c_core               27776  7 
>saa7134_dvb,dvb_pll,mt352,nxt200x,tda1004x,saa7134,ir_kbd_i2c
>ir_common              34692  2 saa7134,ir_kbd_i2c
>videodev               29696  1 saa7134
>v4l1_compat            16260  2 saa7134,videodev
>v4l2_common            28672  3 saa7134,compat_ioctl32,videodev


Any suggestions ?

-- 
Simon Hobson

Visit http://www.magpiesnestpublishing.co.uk/ for books by acclaimed
author Gladys Hobson. Novels - poetry - short stories - ideal as
Christmas stocking fillers. Some available as e-books.

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: Problem setting up HVR-1110
  2008-12-31 10:36 Problem setting up HVR-1110 Simon Hobson
@ 2008-12-31 13:43 ` Simon Hobson
  2009-01-01 15:38   ` hermann pitton
  0 siblings, 1 reply; 5+ messages in thread
From: Simon Hobson @ 2008-12-31 13:43 UTC (permalink / raw)
  To: video4linux-list

I wrote:
>I've got MythTV installed and bought a Hauppage HVR-1110 card for 
>it. The card is detected and the saa7134 driver loaded - but that 
>seems to be it. Everything I can find suggests that the card should 
>be identified automatically (and the TDA1004X driver & firmware 
>loaded), but it isn't.

<snip>

>uname -a reports :
>>Linux eddi 2.6.18-6-xen-amd64 #1 SMP Fri Dec 12 07:02:03 UTC 2008 
>>x86_64 GNU/Linux
>
>
>Yes, this is running in a Xen guest - but I've also tried booting 
>the machine into a non-Xen mode (with non-Xen kernel) and it behaves 
>exactly the same. In both cases, the OS is Debian Lenny.

Hmm, memory isn't what it used to be :-(

Went back and double checked, my Dom0 is Etch. Long story short - 
upgraded guest to 2.6.26, upgraded Xen to run it, fixed all the 
things the Xen upgrade changes, and it now is recognised and the 
firmware loaded etc.

-- 
Simon Hobson

Visit http://www.magpiesnestpublishing.co.uk/ for books by acclaimed
author Gladys Hobson. Novels - poetry - short stories - ideal as
Christmas stocking fillers. Some available as e-books.

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: Problem setting up HVR-1110
  2008-12-31 13:43 ` Simon Hobson
@ 2009-01-01 15:38   ` hermann pitton
  2009-01-01 16:30     ` Simon Hobson
  0 siblings, 1 reply; 5+ messages in thread
From: hermann pitton @ 2009-01-01 15:38 UTC (permalink / raw)
  To: Simon Hobson; +Cc: video4linux-list

Hi Simon,

Am Mittwoch, den 31.12.2008, 13:43 +0000 schrieb Simon Hobson:
> I wrote:
> >I've got MythTV installed and bought a Hauppage HVR-1110 card for 
> >it. The card is detected and the saa7134 driver loaded - but that 
> >seems to be it. Everything I can find suggests that the card should 
> >be identified automatically (and the TDA1004X driver & firmware 
> >loaded), but it isn't.
> 
> <snip>
> 
> >uname -a reports :
> >>Linux eddi 2.6.18-6-xen-amd64 #1 SMP Fri Dec 12 07:02:03 UTC 2008 
> >>x86_64 GNU/Linux
> >
> >
> >Yes, this is running in a Xen guest - but I've also tried booting 
> >the machine into a non-Xen mode (with non-Xen kernel) and it behaves 
> >exactly the same. In both cases, the OS is Debian Lenny.
> 
> Hmm, memory isn't what it used to be :-(
> 
> Went back and double checked, my Dom0 is Etch. Long story short - 
> upgraded guest to 2.6.26, upgraded Xen to run it, fixed all the 
> things the Xen upgrade changes, and it now is recognised and the 
> firmware loaded etc.
> 

yep, 2.6.18 was too old.

We fixed radio and external audio in recently too.

It is in 2.6.28 and was previously untested.

Cheers,
Hermann


--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: Problem setting up HVR-1110
  2009-01-01 15:38   ` hermann pitton
@ 2009-01-01 16:30     ` Simon Hobson
  2009-01-01 17:35       ` hermann pitton
  0 siblings, 1 reply; 5+ messages in thread
From: Simon Hobson @ 2009-01-01 16:30 UTC (permalink / raw)
  To: video4linux-list

hermann pitton wrote:

>yep, 2.6.18 was too old.

Hmm, I'd been going from the Wiki that suggested it was supported in 
2.6.18. From http://www.linuxtv.org/wiki/index.php/DVB-T_PCI_Cards :

>>Supported with the latest 2.6.18 kernel

Anyway, forced me to upgrade a few things AND learn some more about 
fixing stuff I broke !

Mind you, it took some time to figure out why I couldn't find any 
channels. Borrowed the portable telly from another room to check the 
aerial and found ... that I'd got a wonky plug and the pin was pushed 
over and shorting out. Works a lot better with a signal :-/

-- 
Simon Hobson

Visit http://www.magpiesnestpublishing.co.uk/ for books by acclaimed
author Gladys Hobson. Novels - poetry - short stories - ideal as
Christmas stocking fillers. Some available as e-books.

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: Problem setting up HVR-1110
  2009-01-01 16:30     ` Simon Hobson
@ 2009-01-01 17:35       ` hermann pitton
  0 siblings, 0 replies; 5+ messages in thread
From: hermann pitton @ 2009-01-01 17:35 UTC (permalink / raw)
  To: Simon Hobson; +Cc: video4linux-list


Am Donnerstag, den 01.01.2009, 16:30 +0000 schrieb Simon Hobson:
> hermann pitton wrote:
> 
> >yep, 2.6.18 was too old.
> 
> Hmm, I'd been going from the Wiki that suggested it was supported in 
> 2.6.18. From http://www.linuxtv.org/wiki/index.php/DVB-T_PCI_Cards :
> 
> >>Supported with the latest 2.6.18 kernel
> 
> Anyway, forced me to upgrade a few things AND learn some more about 
> fixing stuff I broke !
> 
> Mind you, it took some time to figure out why I couldn't find any 
> channels. Borrowed the portable telly from another room to check the 
> aerial and found ... that I'd got a wonky plug and the pin was pushed 
> over and shorting out. Works a lot better with a signal :-/
> 

2.6.18 does not have it at all and ends here.

#define SAA7134_BOARD_KWORLD_ATSC110   90
#define SAA7134_BOARD_AVERMEDIA_A169_B 91
#define SAA7134_BOARD_AVERMEDIA_A169_B1 92
#define SAA7134_BOARD_MD7134_BRIDGE_2     93
#define SAA7134_BOARD_FLYDVBT_HYBRID_CARDBUS 94
#define SAA7134_BOARD_FLYVIDEO3000_NTSC 95

We are now there including card=104.

#define SAA7134_BOARD_FLYDVBT_HYBRID_CARDBUS 94
#define SAA7134_BOARD_FLYVIDEO3000_NTSC 95
#define SAA7134_BOARD_MEDION_MD8800_QUADRO 96
#define SAA7134_BOARD_FLYDVBS_LR300 97
#define SAA7134_BOARD_PROTEUS_2309 98
#define SAA7134_BOARD_AVERMEDIA_A16AR   99
#define SAA7134_BOARD_ASUS_EUROPA2_HYBRID 100
#define SAA7134_BOARD_PINNACLE_PCTV_310i  101
#define SAA7134_BOARD_AVERMEDIA_STUDIO_507 102
#define SAA7134_BOARD_VIDEOMATE_DVBT_200A  103
#define SAA7134_BOARD_HAUPPAUGE_HVR1110    104
#define SAA7134_BOARD_CINERGY_HT_PCMCIA    105
#define SAA7134_BOARD_ENCORE_ENLTV         106
#define SAA7134_BOARD_ENCORE_ENLTV_FM      107
#define SAA7134_BOARD_CINERGY_HT_PCI       108
#define SAA7134_BOARD_PHILIPS_TIGER_S      109
#define SAA7134_BOARD_AVERMEDIA_M102	   110
#define SAA7134_BOARD_ASUS_P7131_4871	   111
#define SAA7134_BOARD_ASUSTeK_P7131_HYBRID_LNA 112
#define SAA7134_BOARD_ECS_TVP3XP_4CB6  113
#define SAA7134_BOARD_KWORLD_DVBT_210 114
#define SAA7134_BOARD_SABRENT_TV_PCB05     115
#define SAA7134_BOARD_10MOONSTVMASTER3     116
#define SAA7134_BOARD_AVERMEDIA_SUPER_007  117
#define SAA7134_BOARD_BEHOLD_401  	118
#define SAA7134_BOARD_BEHOLD_403  	119
#define SAA7134_BOARD_BEHOLD_403FM	120
#define SAA7134_BOARD_BEHOLD_405	121
#define SAA7134_BOARD_BEHOLD_405FM	122
#define SAA7134_BOARD_BEHOLD_407	123
#define SAA7134_BOARD_BEHOLD_407FM	124
#define SAA7134_BOARD_BEHOLD_409	125
#define SAA7134_BOARD_BEHOLD_505FM	126
#define SAA7134_BOARD_BEHOLD_507_9FM	127
#define SAA7134_BOARD_BEHOLD_COLUMBUS_TVFM 128
#define SAA7134_BOARD_BEHOLD_607_9FM	129
#define SAA7134_BOARD_BEHOLD_M6		130
#define SAA7134_BOARD_TWINHAN_DTV_DVB_3056 131
#define SAA7134_BOARD_GENIUS_TVGO_A11MCE   132
#define SAA7134_BOARD_PHILIPS_SNAKE        133
#define SAA7134_BOARD_CREATIX_CTX953       134
#define SAA7134_BOARD_MSI_TVANYWHERE_AD11  135
#define SAA7134_BOARD_AVERMEDIA_CARDBUS_506 136
#define SAA7134_BOARD_AVERMEDIA_A16D       137
#define SAA7134_BOARD_AVERMEDIA_M115       138
#define SAA7134_BOARD_VIDEOMATE_T750       139
#define SAA7134_BOARD_AVERMEDIA_A700_PRO    140
#define SAA7134_BOARD_AVERMEDIA_A700_HYBRID 141
#define SAA7134_BOARD_BEHOLD_H6      142
#define SAA7134_BOARD_BEHOLD_M63      143
#define SAA7134_BOARD_BEHOLD_M6_EXTRA    144
#define SAA7134_BOARD_AVERMEDIA_M103    145
#define SAA7134_BOARD_ASUSTeK_P7131_ANALOG 146
#define SAA7134_BOARD_ASUSTeK_TIGER_3IN1   147
#define SAA7134_BOARD_ENCORE_ENLTV_FM53 148
#define SAA7134_BOARD_AVERMEDIA_M135A    149
#define SAA7134_BOARD_REAL_ANGEL_220     150
#define SAA7134_BOARD_ADS_INSTANT_HDTV_PCI  151
#define SAA7134_BOARD_ASUSTeK_TIGER         152
#define SAA7134_BOARD_KWORLD_PLUS_TV_ANALOG 153



Also Michael added a bunch of them even later including yours.

		.vendor       = PCI_VENDOR_ID_PHILIPS,
		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
		.subvendor    = 0x0070,
		.subdevice    = 0x6700,
		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1110,
	},{
		.vendor       = PCI_VENDOR_ID_PHILIPS,
		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
		.subvendor    = 0x0070,
		.subdevice    = 0x6701,
		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1110,
	},{
		.vendor       = PCI_VENDOR_ID_PHILIPS,
		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
		.subvendor    = 0x0070,
		.subdevice    = 0x6702,
		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1110,
	},{
		.vendor       = PCI_VENDOR_ID_PHILIPS,
		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
		.subvendor    = 0x0070,
		.subdevice    = 0x6703,
		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1110,
	},{
		.vendor       = PCI_VENDOR_ID_PHILIPS,
		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
		.subvendor    = 0x0070,
		.subdevice    = 0x6704,
		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1110,
	},{
		.vendor       = PCI_VENDOR_ID_PHILIPS,
		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
		.subvendor    = 0x0070,
		.subdevice    = 0x6705,
		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1110,
	},{

And that's why you had UNKNOWN/GENERIC detected.

What I get in dmesg is :

>saa7130/34: v4l2 driver version 0.2.14 loaded
>PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
>saa7133[0]: found at 0000:00:00.0, rev: 209, irq: 17, latency: 32, 
>mmio: 0xf4100000
>saa7133[0]: subsystem: 0070:6701, board: UNKNOWN/GENERIC
[card=0,autodetected]
>saa7133[0]: board init: gpio is 6400000

Also LNA activation for analog was missing.

http://linuxtv.org/hg/v4l-dvb/rev/b227949c41ad

Yesterday I could not believe that /me should have hardware hitting all
major bugs in Fedora 10, some known since FC6 and even improved now.

Now I do ...

If in doubt, always trust the code :)

Cheers,
Hermann




--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2009-01-01 17:35 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-12-31 10:36 Problem setting up HVR-1110 Simon Hobson
2008-12-31 13:43 ` Simon Hobson
2009-01-01 15:38   ` hermann pitton
2009-01-01 16:30     ` Simon Hobson
2009-01-01 17:35       ` hermann pitton

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox