Re: [PATCH 12/18] ASoC: codecs: mt6357: add MT6357 codec

[Alexandre Mergnat <amergnat@baylibre.com>]

On 26/02/2024 17:09, Mark Brown wrote:
> On Mon, Feb 26, 2024 at 03:01:50PM +0100, amergnat@baylibre.com wrote:
> 
>> index 000000000000..13e95c227114
>> --- /dev/null
>> +++ b/sound/soc/codecs/mt6357.c
>> @@ -0,0 +1,1805 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * MT6357 ALSA SoC audio codec driver
>> + *
> 
> Please use a C++ comment for the whole comment to make it clearer that
> this is intentional.

ok

> 
>> +static void set_playback_gpio(struct mt6357_priv *priv, bool enable)
>> +{
>> +	if (enable) {
>> +		/* set gpio mosi mode */
>> +		regmap_write(priv->regmap, MT6357_GPIO_MODE2_CLR, GPIO_MODE2_CLEAR_ALL);
>> +		regmap_write(priv->regmap, MT6357_GPIO_MODE2_SET, GPIO8_MODE_SET_AUD_CLK_MOSI |
>> +								  GPIO9_MODE_SET_AUD_DAT_MOSI0 |
>> +								  GPIO10_MODE_SET_AUD_DAT_MOSI1 |
>> +								  GPIO11_MODE_SET_AUD_SYNC_MOSI);
> 
> This would be a lot more legible if you worked out the values to set and
> then had a single set of writes, currently the indentation makes it very
> hard to read.  Similarly for other similar functions.

ok

> 
>> +static int mt6357_put_volsw(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol)
>> +{
>> +	struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
>> +	struct mt6357_priv *priv = snd_soc_component_get_drvdata(component);
>> +	struct soc_mixer_control *mc = (struct soc_mixer_control *)kcontrol->private_value;
>> +	unsigned int reg;
>> +	int ret;
>> +
>> +	ret = snd_soc_put_volsw(kcontrol, ucontrol);
>> +	if (ret < 0)
>> +		return ret;
>> +
>> +	switch (mc->reg) {
>> +	case MT6357_ZCD_CON2:
>> +		regmap_read(priv->regmap, MT6357_ZCD_CON2, &reg);
>> +		priv->ana_gain[ANALOG_VOLUME_HPOUTL] =
>> +			(reg & AUD_HPL_GAIN_MASK) >> AUD_HPL_GAIN_SFT;
>> +		priv->ana_gain[ANALOG_VOLUME_HPOUTR] =
>> +			(reg & AUD_HPR_GAIN_MASK) >> AUD_HPR_GAIN_SFT;
>> +		break;
> 
> It would probably be less code and would definitely be clearer and
> simpler to just read the values when we need them rather than constatly
> keeping a cache separate to the register cache.

Actually you must save the values because the gain selected by the user 
will be override to do a ramp => volume_ramp(.....):
- When you switch on the HP, you start from gain=-40db to final_gain 
(selected by user).
- When you switch off the HP, you start from final_gain (selected by 
user) to gain=-40db.

Also, the microphone's gain change when it's enabled/disabled.

So, it can implemented differently but currently it's aligned with the 
other MTK codecs and I don't see any resource wasted here.

> 
>> +	/* ul channel swap */
>> +	SOC_SINGLE("UL LR Swap", MT6357_AFE_UL_DL_CON0, AFE_UL_LR_SWAP_SFT, 1, 0),
> 
> On/off controls should end in Switch.

Sorry, I don't understand your comment. Can you reword it please ?

> 
>> +static const char * const hslo_mux_map[] = {
>> +	"Open", "DACR", "Playback", "Test mode"
>> +};
>> +
>> +static int hslo_mux_map_value[] = {
>> +	0x0, 0x1, 0x2, 0x3,
>> +};
> 
> Why not just use a normal mux here, there's no missing values or
> reordering?  Similarly for other muxes.

I've dug into some other codecs and it's done like that, but I've 
probably misunderstood something.

The only bad thing I see is enum is missing currently:

enum {
	PGA_MUX_OPEN = 0,
	PGA_MUX_DACR,
	PGA_MUX_PB,
	PGA_MUX_TM,
	PGA_MUX_MASK = 0x3,
};

static const char * const hslo_mux_map[] = {
	"Open", "DACR", "Playback", "Test mode"
};

static int hslo_mux_map_value[] = {
	PGA_MUX_OPEN, PGA_MUX_DACR, PGA_MUX_PB, PGA_MUX_TM,
};

> 
>> +static unsigned int mt6357_read(struct snd_soc_component *codec, unsigned int reg)
>> +{
>> +	struct mt6357_priv *priv = snd_soc_component_get_drvdata(codec);
>> +	unsigned int val;
>> +
>> +	pr_debug("%s() reg = 0x%x", __func__, reg);
>> +	regmap_read(priv->regmap, reg, &val);
>> +	return val;
>> +}
> 
> Remove these, there are vastly more logging facilities as standard in
> the regmap core.

ok

> 
>> +/* Reg bit defines */
>> +/* MT6357_GPIO_DIR0 */
>> +#define GPIO8_DIR_MASK				BIT(8)
>> +#define GPIO8_DIR_INPUT				0
> 
> Please namespace your defines, these look very generic.

ok

-- 
Regards,
Alexandre