From: "Kevin D. Kissell" <kevink@mips.com>
To: "Florian Lohoff" <flo@rfc822.org>, <linux@cthulhu.engr.sgi.com>
Subject: Re: Decstation 5000/150 2.3.21 Boot successs
Date: Thu, 6 Jan 2000 10:12:21 +0100 [thread overview]
Message-ID: <000601bf5826$273af500$0ceca8c0@satanas.mips.com> (raw)
The "setting flush to zero/Unimlemented exception"
problem is almost certainly due to the fact that the
DECstation binaries were compiled for R3000-based
platforms with R3K-style FPUs which have 32 single-precision
FP regs that can also be treated pairwise as 16
double-precision registers. I didn't know that the 5000 line
had R4000 CPUs in them, but on the basis of your reported
CPU revision number, that's what you've got.
The default SGI/MIPS Linux kernel startup sets the
"FR" bit in the CP0.Status register, which enables
R4000-style FPU registers, which is to say a full
compliment of 32 double-precision registers. This
has the side-effect of making the kernel incompatible
with the distributed mipsel binaries and the distributed
DECstation root file system, since those binaries which
do double-precision floating point load their initial values
from memory as two singles. That works on an R3000
or an R4000-with-FR=0, but not on an R4000-with-FR=1.
If FR=1, the data in the registers is garbage, the FP
ops trap on unimplemented exceptions, which first
retry the instruction with flush-to-zero mode in a
desperate hope that that will solve the problem,
then call the fragmentatary SW emulator in the
kernel, which only handles a few cases, then
skip the instruction, printing the console message
that it "should" have sent a SIGFPE. Hence the
output. And hence the bizzare behaviour of awk,
ps, and a number of other basic programs that do
minimal FP as the system comes up (procps?).
It took me a while to figure this out when I ran into
it doing a little-endian port of Linux 2.2.12 to an R5260,
as you might imagine. Unless things have been drastically
scrambled for 2.3.x, the code controlling this is in
arch/mips/kernel/head.S. What we did at MIPS was
to add a config option to determine which FPU model
is desired. The truly elegant thing would be to examine
the a.out file and manage Status.FR dynamically, but
a quick inspection turned up no clean mechanism in
the Linux kernel for passing such architecture-dependent
information from the generic a.out file parsing to the
thread creation machinery, so that will be a later
exercise. Thoward the end of the kernel entry point
(kernel_entry), our revised code looks a bit like this:
/* Disable coprocessors */
mfc0 t0, CP0_STATUS
#ifdef CONFIG_MIPS_32FR
li t1, ~(ST0_CU1|ST0_CU2|ST0_CU3|ST0_KX|ST0_SX)
#else
li t1, ~(ST0_CU1|ST0_CU2|ST0_CU3|ST0_KX|ST0_SX|ST0_FR)
#endif
and t0, t1
or t0, ST0_CU0
mtc0 t0, CP0_STATUS
1: jal start_kernel
nop
The "#ifdef/else/endif" sequence is our addition. For a
quick hack, just add ST0_FR to the set of bits being
inverted in the existing code.
Hope this helps,
Kevin K.
__
Kevin D. Kissell
MIPS Technologies European Architecture Lab
kevink@mips.com
Tel. +33.4.78.38.70.67
FAX. +33.4.78.38.70.68
-----Original Message-----
From: Florian Lohoff <flo@rfc822.org>
To: linux@cthulhu.engr.sgi.com <linux@cthulhu.engr.sgi.com>
Date: Wednesday, January 05, 2000 11:17 PM
Subject: Decstation 5000/150 2.3.21 Boot successs
>
>Hi,
>this is is a short output of the 2.3.21 booting on the Decstation
>5000/150 ... This is the current oss.sgi.com CVS.
>
>--------------------------------------------------------------
>This DECstation is a DS5000/1xx
>Loading R4000 MMU routines.
>CPU revision is: 00000430
>Primary instruction cache 8kb, linesize 16 bytes)
>Primary data cache 8kb, linesize 16 bytes)
>Secondary cache sized at 1024K linesize 32
>Linux version 2.3.21 (root@repeat) (gcc version egcs-2.90.27 980315 (egcs-1.0.2
release)) #1 Tue Jan 4 18:39:20 GMT 2000
>Calibrating delay loop... 49.81 BogoMIPS
>Memory: 62652k/65532k available (1068k kernel code, 1524k data)
>Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
>Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
>Checking for 'wait' instruction... unavailable.
>POSIX conformance testing by UNIFIX
>TURBOchannel rev. 1 at 12.5 MHz (no parity)
> slot 0: DEC PMAZ-AA V5.3d
> slot 1: DEC PMAZ-AA V5.3b
> slot 2: DEC PMAF-FA V1.1
>Linux NET4.0 for Linux 2.3
>Based upon Swansea University Computer Society NET3.039
>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
>NET4: Linux TCP/IP 1.0 for NET4.0
>IP Protocols: ICMP, UDP, TCP
>TCP: Hash tables configured (established 4096 bind 8192)
>Starting kswapd v1.6
>DECstation Z8530 serial driver version 0.03
>tty00 at 0xbc100001 (irq = 4) is a Z85C30 SCC
>tty01 at 0xbc100009 (irq = 4) is a Z85C30 SCC
>tty02 at 0xbc180001 (irq = 4) is a Z85C30 SCC
>tty03 at 0xbc180009 (irq = 4) is a Z85C30 SCC
>SCSI ID 7 Clk 25MHz CCF=5 TOut 167 NCR53C9x(esp236)
>SCSI ID 7 Clk 12MHz CCF=3 TOut 139 NCR53C9x(esp236)
>SCSI ID 7 Clk 12MHz CCF=3 TOut 139 NCR53C9x(esp236)
>ESP: Total of 3 ESP hosts found, 3 actually in use.
>scsi0 : ESP236 (NCR53C9x)
>scsi1 : ESP236 (NCR53C9x)
>scsi2 : ESP236 (NCR53C9x)
>scsi : 3 hosts.
> Vendor: Quantum Model: XP34300 Rev: L912
> Type: Direct-Access ANSI SCSI revision: 02
>Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> Vendor: SEAGATE Model: ST15150N Rev: 8902
> Type: Direct-Access ANSI SCSI revision: 02
>Detected scsi disk sdb at scsi0, channel 0, id 2, lun 0
>scsi : detected 2 SCSI disks total.
>esp0: target 0 [period 200ns offset 15 5.00MHz synchronous SCSI]
>SCSI device sda: hdwr sector= 512 bytes. Sectors= 8399520 [4101 MB] [4.1 GB]
>esp0: target 2 [period 200ns offset 15 5.00MHz synchronous SCSI]
>SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8388315 [4095 MB] [4.1 GB]
>declance.c: v0.008 by Linux Mips DECstation task force
>eth0: IOASIC onboard LANCE, addr = 08:00:2b:28:f0:a3, irq = 3
>Sending BOOTP requests.... OK
>IP-Config: Got BOOTP answer from 193.189.250.46, my address is 193.189.250.44
>-----------------------------------------------------
>
>I see some more ugly things:
>
>Setting flush to zero for dpkg-source.
>Unimplemented exception for insn 4620a0a4 at 0x0046f084 in dpkg-source.
>Should send SIGFPE to dpkg-source
>Setting flush to zero for dpkg-source.
>Unimplemented exception for insn 4620a0a4 at 0x0046f084 in dpkg-source.
>Should send SIGFPE to dpkg-source
>Setting flush to zero for dpkg-source.
>Unimplemented exception for insn 4620a0a4 at 0x0046f084 in dpkg-source.
>Should send SIGFPE to dpkg-source
>
>And this ...
>
>Bug in get_wchan
>
>This seems to be a result of buggy "procps" ...
>
>Flo
>--
>Florian Lohoff flo@rfc822.org +49-5241-470566
> ... The failure can be random; however, when it does occur, it is
> catastrophic and is repeatable ... Cisco Field Notice
>
WARNING: multiple messages have this Message-ID (diff)
From: "Kevin D. Kissell" <kevink@mips.com>
To: Florian Lohoff <flo@rfc822.org>, linux@cthulhu.engr.sgi.com
Subject: Re: Decstation 5000/150 2.3.21 Boot successs
Date: Thu, 6 Jan 2000 10:12:21 +0100 [thread overview]
Message-ID: <000601bf5826$273af500$0ceca8c0@satanas.mips.com> (raw)
Message-ID: <20000106091221.XO6tV0vzb5yLjst6VWH2mQ0tKW6y_RQGOG6XK9xf9qQ@z> (raw)
The "setting flush to zero/Unimlemented exception"
problem is almost certainly due to the fact that the
DECstation binaries were compiled for R3000-based
platforms with R3K-style FPUs which have 32 single-precision
FP regs that can also be treated pairwise as 16
double-precision registers. I didn't know that the 5000 line
had R4000 CPUs in them, but on the basis of your reported
CPU revision number, that's what you've got.
The default SGI/MIPS Linux kernel startup sets the
"FR" bit in the CP0.Status register, which enables
R4000-style FPU registers, which is to say a full
compliment of 32 double-precision registers. This
has the side-effect of making the kernel incompatible
with the distributed mipsel binaries and the distributed
DECstation root file system, since those binaries which
do double-precision floating point load their initial values
from memory as two singles. That works on an R3000
or an R4000-with-FR=0, but not on an R4000-with-FR=1.
If FR=1, the data in the registers is garbage, the FP
ops trap on unimplemented exceptions, which first
retry the instruction with flush-to-zero mode in a
desperate hope that that will solve the problem,
then call the fragmentatary SW emulator in the
kernel, which only handles a few cases, then
skip the instruction, printing the console message
that it "should" have sent a SIGFPE. Hence the
output. And hence the bizzare behaviour of awk,
ps, and a number of other basic programs that do
minimal FP as the system comes up (procps?).
It took me a while to figure this out when I ran into
it doing a little-endian port of Linux 2.2.12 to an R5260,
as you might imagine. Unless things have been drastically
scrambled for 2.3.x, the code controlling this is in
arch/mips/kernel/head.S. What we did at MIPS was
to add a config option to determine which FPU model
is desired. The truly elegant thing would be to examine
the a.out file and manage Status.FR dynamically, but
a quick inspection turned up no clean mechanism in
the Linux kernel for passing such architecture-dependent
information from the generic a.out file parsing to the
thread creation machinery, so that will be a later
exercise. Thoward the end of the kernel entry point
(kernel_entry), our revised code looks a bit like this:
/* Disable coprocessors */
mfc0 t0, CP0_STATUS
#ifdef CONFIG_MIPS_32FR
li t1, ~(ST0_CU1|ST0_CU2|ST0_CU3|ST0_KX|ST0_SX)
#else
li t1, ~(ST0_CU1|ST0_CU2|ST0_CU3|ST0_KX|ST0_SX|ST0_FR)
#endif
and t0, t1
or t0, ST0_CU0
mtc0 t0, CP0_STATUS
1: jal start_kernel
nop
The "#ifdef/else/endif" sequence is our addition. For a
quick hack, just add ST0_FR to the set of bits being
inverted in the existing code.
Hope this helps,
Kevin K.
__
Kevin D. Kissell
MIPS Technologies European Architecture Lab
kevink@mips.com
Tel. +33.4.78.38.70.67
FAX. +33.4.78.38.70.68
-----Original Message-----
From: Florian Lohoff <flo@rfc822.org>
To: linux@cthulhu.engr.sgi.com <linux@cthulhu.engr.sgi.com>
Date: Wednesday, January 05, 2000 11:17 PM
Subject: Decstation 5000/150 2.3.21 Boot successs
>
>Hi,
>this is is a short output of the 2.3.21 booting on the Decstation
>5000/150 ... This is the current oss.sgi.com CVS.
>
>--------------------------------------------------------------
>This DECstation is a DS5000/1xx
>Loading R4000 MMU routines.
>CPU revision is: 00000430
>Primary instruction cache 8kb, linesize 16 bytes)
>Primary data cache 8kb, linesize 16 bytes)
>Secondary cache sized at 1024K linesize 32
>Linux version 2.3.21 (root@repeat) (gcc version egcs-2.90.27 980315 (egcs-1.0.2
release)) #1 Tue Jan 4 18:39:20 GMT 2000
>Calibrating delay loop... 49.81 BogoMIPS
>Memory: 62652k/65532k available (1068k kernel code, 1524k data)
>Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
>Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
>Checking for 'wait' instruction... unavailable.
>POSIX conformance testing by UNIFIX
>TURBOchannel rev. 1 at 12.5 MHz (no parity)
> slot 0: DEC PMAZ-AA V5.3d
> slot 1: DEC PMAZ-AA V5.3b
> slot 2: DEC PMAF-FA V1.1
>Linux NET4.0 for Linux 2.3
>Based upon Swansea University Computer Society NET3.039
>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
>NET4: Linux TCP/IP 1.0 for NET4.0
>IP Protocols: ICMP, UDP, TCP
>TCP: Hash tables configured (established 4096 bind 8192)
>Starting kswapd v1.6
>DECstation Z8530 serial driver version 0.03
>tty00 at 0xbc100001 (irq = 4) is a Z85C30 SCC
>tty01 at 0xbc100009 (irq = 4) is a Z85C30 SCC
>tty02 at 0xbc180001 (irq = 4) is a Z85C30 SCC
>tty03 at 0xbc180009 (irq = 4) is a Z85C30 SCC
>SCSI ID 7 Clk 25MHz CCF=5 TOut 167 NCR53C9x(esp236)
>SCSI ID 7 Clk 12MHz CCF=3 TOut 139 NCR53C9x(esp236)
>SCSI ID 7 Clk 12MHz CCF=3 TOut 139 NCR53C9x(esp236)
>ESP: Total of 3 ESP hosts found, 3 actually in use.
>scsi0 : ESP236 (NCR53C9x)
>scsi1 : ESP236 (NCR53C9x)
>scsi2 : ESP236 (NCR53C9x)
>scsi : 3 hosts.
> Vendor: Quantum Model: XP34300 Rev: L912
> Type: Direct-Access ANSI SCSI revision: 02
>Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> Vendor: SEAGATE Model: ST15150N Rev: 8902
> Type: Direct-Access ANSI SCSI revision: 02
>Detected scsi disk sdb at scsi0, channel 0, id 2, lun 0
>scsi : detected 2 SCSI disks total.
>esp0: target 0 [period 200ns offset 15 5.00MHz synchronous SCSI]
>SCSI device sda: hdwr sector= 512 bytes. Sectors= 8399520 [4101 MB] [4.1 GB]
>esp0: target 2 [period 200ns offset 15 5.00MHz synchronous SCSI]
>SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8388315 [4095 MB] [4.1 GB]
>declance.c: v0.008 by Linux Mips DECstation task force
>eth0: IOASIC onboard LANCE, addr = 08:00:2b:28:f0:a3, irq = 3
>Sending BOOTP requests.... OK
>IP-Config: Got BOOTP answer from 193.189.250.46, my address is 193.189.250.44
>-----------------------------------------------------
>
>I see some more ugly things:
>
>Setting flush to zero for dpkg-source.
>Unimplemented exception for insn 4620a0a4 at 0x0046f084 in dpkg-source.
>Should send SIGFPE to dpkg-source
>Setting flush to zero for dpkg-source.
>Unimplemented exception for insn 4620a0a4 at 0x0046f084 in dpkg-source.
>Should send SIGFPE to dpkg-source
>Setting flush to zero for dpkg-source.
>Unimplemented exception for insn 4620a0a4 at 0x0046f084 in dpkg-source.
>Should send SIGFPE to dpkg-source
>
>And this ...
>
>Bug in get_wchan
>
>This seems to be a result of buggy "procps" ...
>
>Flo
>--
>Florian Lohoff flo@rfc822.org +49-5241-470566
> ... The failure can be random; however, when it does occur, it is
> catastrophic and is repeatable ... Cisco Field Notice
>
next reply other threads:[~2000-01-06 9:12 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2000-01-06 9:12 Kevin D. Kissell [this message]
2000-01-06 9:12 ` Decstation 5000/150 2.3.21 Boot successs Kevin D. Kissell
2000-01-06 14:26 ` Ralf Baechle
2000-01-06 19:10 ` William J. Earl
2000-01-06 18:57 ` William J. Earl
2000-01-06 18:57 ` William J. Earl
2000-01-07 19:09 ` Harald Koerfgen
2000-01-07 23:29 ` Ralf Baechle
2000-01-08 1:30 ` William J. Earl
2000-01-08 23:12 ` Newer build tools John Michael Clemens
2000-01-10 4:01 ` Ralf Baechle
-- strict thread matches above, loose matches on Subject: below --
2000-01-06 15:19 Decstation 5000/150 2.3.21 Boot successs Kevin D. Kissell
2000-01-06 15:19 ` Kevin D. Kissell
2000-01-06 23:54 ` Ralf Baechle
2000-01-07 1:50 ` William J. Earl
2000-01-05 21:18 Florian Lohoff
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='000601bf5826$273af500$0ceca8c0@satanas.mips.com' \
--to=kevink@mips.com \
--cc=flo@rfc822.org \
--cc=linux@cthulhu.engr.sgi.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox