* Move arch/mips/philips to arch/mips/nxp
@ 2008-02-27 10:50 Daniel Laird
2008-02-28 9:42 ` Ralf Baechle
0 siblings, 1 reply; 4+ messages in thread
From: Daniel Laird @ 2008-02-27 10:50 UTC (permalink / raw)
To: linux-mips
[-- Attachment #1: Type: text/plain, Size: 577 bytes --]
This patch moves arch/mips/philips to arch/mips/nxp
It also modifies a couple of places from Philips -> nxp for more consistancy.
This is in preparation for a new set of chip patches coming soon.
The patch has no other work in in it is primarily a move of current
code to a new location.
Have run checkpatch.pl and there are many problems with the patch.
However none of these are new and are already existing issues in the code base.
A new patch (to be posted later) will clean up some of these as well.
Have rebuilt pnx8550_*_defconfig
Hope it is accepted.
Daniel Laird
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: philips_to_nxp.patch --]
[-- Type: text/x-patch; name=philips_to_nxp.patch, Size: 106974 bytes --]
diff -urN linux-2.6.24.2.orig/arch/mips/Kconfig linux-2.6.24.2/arch/mips/Kconfig
--- linux-2.6.24.2.orig/arch/mips/Kconfig 2008-02-26 08:22:58.000000000 +0000
+++ linux-2.6.24.2/arch/mips/Kconfig 2008-02-26 08:32:25.000000000 +0000
@@ -312,12 +312,12 @@
select GENERIC_HARDIRQS_NO__DO_IRQ
config PNX8550_JBS
- bool "Philips PNX8550 based JBS board"
+ bool "NXP PNX8550 based JBS board"
select PNX8550
select SYS_SUPPORTS_LITTLE_ENDIAN
config PNX8550_STB810
- bool "Philips PNX8550 based STB810 board"
+ bool "NXP PNX8550 based STB810 board"
select PNX8550
select SYS_SUPPORTS_LITTLE_ENDIAN
diff -urN linux-2.6.24.2.orig/arch/mips/kernel/cpu-probe.c linux-2.6.24.2/arch/mips/kernel/cpu-probe.c
--- linux-2.6.24.2.orig/arch/mips/kernel/cpu-probe.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/kernel/cpu-probe.c 2008-02-26 08:36:32.000000000 +0000
@@ -771,7 +771,7 @@
}
}
-static inline void cpu_probe_philips(struct cpuinfo_mips *c)
+static inline void cpu_probe_nxp(struct cpuinfo_mips *c)
{
decode_configs(c);
switch (c->processor_id & 0xff00) {
@@ -780,7 +780,7 @@
c->isa_level = MIPS_CPU_ISA_M32R1;
break;
default:
- panic("Unknown Philips Core!"); /* REVISIT: die? */
+ panic("Unknown NXP Core!"); /* REVISIT: die? */
break;
}
}
@@ -878,7 +878,7 @@
case CPU_SR71000: name = "Sandcraft SR71000"; break;
case CPU_BCM3302: name = "Broadcom BCM3302"; break;
case CPU_BCM4710: name = "Broadcom BCM4710"; break;
- case CPU_PR4450: name = "Philips PR4450"; break;
+ case CPU_PR4450: name = "NXP PR4450"; break;
case CPU_LOONGSON2: name = "ICT Loongson-2"; break;
default:
BUG();
@@ -916,8 +916,8 @@
case PRID_COMP_SANDCRAFT:
cpu_probe_sandcraft(c);
break;
- case PRID_COMP_PHILIPS:
- cpu_probe_philips(c);
+ case PRID_COMP_NXP:
+ cpu_probe_nxp(c);
break;
default:
c->cputype = CPU_UNKNOWN;
diff -urN linux-2.6.24.2.orig/arch/mips/Makefile linux-2.6.24.2/arch/mips/Makefile
--- linux-2.6.24.2.orig/arch/mips/Makefile 2008-02-26 08:22:58.000000000 +0000
+++ linux-2.6.24.2/arch/mips/Makefile 2008-02-26 08:36:21.000000000 +0000
@@ -410,21 +410,21 @@
load-$(CONFIG_TANBAC_TB022X) += 0xffffffff80000000
#
-# Common Philips PNX8550
+# Common NXP PNX8550
#
-core-$(CONFIG_SOC_PNX8550) += arch/mips/philips/pnx8550/common/
+core-$(CONFIG_SOC_PNX8550) += arch/mips/nxp/pnx8550/common/
cflags-$(CONFIG_SOC_PNX8550) += -Iinclude/asm-mips/mach-pnx8550
#
-# Philips PNX8550 JBS board
+# NXP PNX8550 JBS board
#
-libs-$(CONFIG_PNX8550_JBS) += arch/mips/philips/pnx8550/jbs/
+libs-$(CONFIG_PNX8550_JBS) += arch/mips/nxp/pnx8550/jbs/
#cflags-$(CONFIG_PNX8550_JBS) += -Iinclude/asm-mips/mach-pnx8550
load-$(CONFIG_PNX8550_JBS) += 0xffffffff80060000
-# Philips PNX8550 STB810 board
+# NXP PNX8550 STB810 board
#
-libs-$(CONFIG_PNX8550_STB810) += arch/mips/philips/pnx8550/stb810/
+libs-$(CONFIG_PNX8550_STB810) += arch/mips/nxp/pnx8550/stb810/
load-$(CONFIG_PNX8550_STB810) += 0xffffffff80060000
# NEC EMMA2RH boards
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/gdb_hook.c linux-2.6.24.2/arch/mips/nxp/pnx8550/common/gdb_hook.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/gdb_hook.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/gdb_hook.c 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,109 @@
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
+ *
+ * ########################################################################
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ *
+ * This is the interface to the remote debugger stub.
+ *
+ */
+#include <linux/types.h>
+#include <linux/serial.h>
+#include <linux/serialP.h>
+#include <linux/serial_reg.h>
+#include <linux/serial_ip3106.h>
+
+#include <asm/serial.h>
+#include <asm/io.h>
+
+#include <uart.h>
+
+static struct serial_state rs_table[IP3106_NR_PORTS] = {
+};
+static struct async_struct kdb_port_info = {0};
+
+void rs_kgdb_hook(int tty_no)
+{
+ struct serial_state *ser = &rs_table[tty_no];
+
+ kdb_port_info.state = ser;
+ kdb_port_info.magic = SERIAL_MAGIC;
+ kdb_port_info.port = tty_no;
+ kdb_port_info.flags = ser->flags;
+
+ /*
+ * Clear all interrupts
+ */
+ /* Clear all the transmitter FIFO counters (pointer and status) */
+ ip3106_lcr(UART_BASE, tty_no) |= IP3106_UART_LCR_TX_RST;
+ /* Clear all the receiver FIFO counters (pointer and status) */
+ ip3106_lcr(UART_BASE, tty_no) |= IP3106_UART_LCR_RX_RST;
+ /* Clear all interrupts */
+ ip3106_iclr(UART_BASE, tty_no) = IP3106_UART_INT_ALLRX |
+ IP3106_UART_INT_ALLTX;
+
+ /*
+ * Now, initialize the UART
+ */
+ ip3106_lcr(UART_BASE, tty_no) = IP3106_UART_LCR_8BIT;
+ ip3106_baud(UART_BASE, tty_no) = 5; // 38400 Baud
+}
+
+int putDebugChar(char c)
+{
+ /* Wait until FIFO not full */
+ while (((ip3106_fifo(UART_BASE, kdb_port_info.port) & IP3106_UART_FIFO_TXFIFO) >> 16) >= 16)
+ ;
+ /* Send one char */
+ ip3106_fifo(UART_BASE, kdb_port_info.port) = c;
+
+ return 1;
+}
+
+char getDebugChar(void)
+{
+ char ch;
+
+ /* Wait until there is a char in the FIFO */
+ while (!((ip3106_fifo(UART_BASE, kdb_port_info.port) &
+ IP3106_UART_FIFO_RXFIFO) >> 8))
+ ;
+ /* Read one char */
+ ch = ip3106_fifo(UART_BASE, kdb_port_info.port) &
+ IP3106_UART_FIFO_RBRTHR;
+ /* Advance the RX FIFO read pointer */
+ ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_RX_NEXT;
+ return (ch);
+}
+
+void rs_disable_debug_interrupts(void)
+{
+ ip3106_ien(UART_BASE, kdb_port_info.port) = 0; /* Disable all interrupts */
+}
+
+void rs_enable_debug_interrupts(void)
+{
+ /* Clear all the transmitter FIFO counters (pointer and status) */
+ ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_TX_RST;
+ /* Clear all the receiver FIFO counters (pointer and status) */
+ ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_RX_RST;
+ /* Clear all interrupts */
+ ip3106_iclr(UART_BASE, kdb_port_info.port) = IP3106_UART_INT_ALLRX |
+ IP3106_UART_INT_ALLTX;
+ ip3106_ien(UART_BASE, kdb_port_info.port) = IP3106_UART_INT_ALLRX; /* Enable RX interrupts */
+}
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/int.c linux-2.6.24.2/arch/mips/nxp/pnx8550/common/int.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/int.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/int.c 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,238 @@
+/*
+ *
+ * Copyright (C) 2005 Embedded Alley Solutions, Inc
+ * Ported to 2.6.
+ *
+ * Per Hallsmark, per.hallsmark@mvista.com
+ * Copyright (C) 2000, 2001 MIPS Technologies, Inc.
+ * Copyright (C) 2001 Ralf Baechle
+ *
+ * Cleaned up and bug fixing: Pete Popov, ppopov@embeddedalley.com
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ */
+#include <linux/compiler.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/kernel_stat.h>
+#include <linux/random.h>
+#include <linux/module.h>
+
+#include <asm/io.h>
+#include <asm/gdb-stub.h>
+#include <int.h>
+#include <uart.h>
+
+/* default prio for interrupts */
+/* first one is a no-no so therefore always prio 0 (disabled) */
+static char gic_prio[PNX8550_INT_GIC_TOTINT] = {
+ 0, 1, 1, 1, 1, 15, 1, 1, 1, 1, // 0 - 9
+ 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 10 - 19
+ 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 20 - 29
+ 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 30 - 39
+ 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 40 - 49
+ 1, 1, 1, 1, 1, 1, 1, 1, 2, 1, // 50 - 59
+ 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 60 - 69
+ 1 // 70
+};
+
+static void hw0_irqdispatch(int irq)
+{
+ /* find out which interrupt */
+ irq = PNX8550_GIC_VECTOR_0 >> 3;
+
+ if (irq == 0) {
+ printk("hw0_irqdispatch: irq 0, spurious interrupt?\n");
+ return;
+ }
+ do_IRQ(PNX8550_INT_GIC_MIN + irq);
+}
+
+
+static void timer_irqdispatch(int irq)
+{
+ irq = (0x01c0 & read_c0_config7()) >> 6;
+
+ if (unlikely(irq == 0)) {
+ printk("timer_irqdispatch: irq 0, spurious interrupt?\n");
+ return;
+ }
+
+ if (irq & 0x1)
+ do_IRQ(PNX8550_INT_TIMER1);
+ if (irq & 0x2)
+ do_IRQ(PNX8550_INT_TIMER2);
+ if (irq & 0x4)
+ do_IRQ(PNX8550_INT_TIMER3);
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+ unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM;
+
+ if (pending & STATUSF_IP2)
+ hw0_irqdispatch(2);
+ else if (pending & STATUSF_IP7) {
+ if (read_c0_config7() & 0x01c0)
+ timer_irqdispatch(7);
+ } else
+ spurious_interrupt();
+}
+
+static inline void modify_cp0_intmask(unsigned clr_mask, unsigned set_mask)
+{
+ unsigned long status = read_c0_status();
+
+ status &= ~((clr_mask & 0xFF) << 8);
+ status |= (set_mask & 0xFF) << 8;
+
+ write_c0_status(status);
+}
+
+static inline void mask_gic_int(unsigned int irq_nr)
+{
+ /* interrupt disabled, bit 26(WE_ENABLE)=1 and bit 16(enable)=0 */
+ PNX8550_GIC_REQ(irq_nr) = 1<<28; /* set priority to 0 */
+}
+
+static inline void unmask_gic_int(unsigned int irq_nr)
+{
+ /* set prio mask to lower four bits and enable interrupt */
+ PNX8550_GIC_REQ(irq_nr) = (1<<26 | 1<<16) | (1<<28) | gic_prio[irq_nr];
+}
+
+static inline void mask_irq(unsigned int irq_nr)
+{
+ if ((PNX8550_INT_CP0_MIN <= irq_nr) && (irq_nr <= PNX8550_INT_CP0_MAX)) {
+ modify_cp0_intmask(1 << irq_nr, 0);
+ } else if ((PNX8550_INT_GIC_MIN <= irq_nr) &&
+ (irq_nr <= PNX8550_INT_GIC_MAX)) {
+ mask_gic_int(irq_nr - PNX8550_INT_GIC_MIN);
+ } else if ((PNX8550_INT_TIMER_MIN <= irq_nr) &&
+ (irq_nr <= PNX8550_INT_TIMER_MAX)) {
+ modify_cp0_intmask(1 << 7, 0);
+ } else {
+ printk("mask_irq: irq %d doesn't exist!\n", irq_nr);
+ }
+}
+
+static inline void unmask_irq(unsigned int irq_nr)
+{
+ if ((PNX8550_INT_CP0_MIN <= irq_nr) && (irq_nr <= PNX8550_INT_CP0_MAX)) {
+ modify_cp0_intmask(0, 1 << irq_nr);
+ } else if ((PNX8550_INT_GIC_MIN <= irq_nr) &&
+ (irq_nr <= PNX8550_INT_GIC_MAX)) {
+ unmask_gic_int(irq_nr - PNX8550_INT_GIC_MIN);
+ } else if ((PNX8550_INT_TIMER_MIN <= irq_nr) &&
+ (irq_nr <= PNX8550_INT_TIMER_MAX)) {
+ modify_cp0_intmask(0, 1 << 7);
+ } else {
+ printk("mask_irq: irq %d doesn't exist!\n", irq_nr);
+ }
+}
+
+int pnx8550_set_gic_priority(int irq, int priority)
+{
+ int gic_irq = irq-PNX8550_INT_GIC_MIN;
+ int prev_priority = PNX8550_GIC_REQ(gic_irq) & 0xf;
+
+ gic_prio[gic_irq] = priority;
+ PNX8550_GIC_REQ(gic_irq) |= (0x10000000 | gic_prio[gic_irq]);
+
+ return prev_priority;
+}
+
+static struct irq_chip level_irq_type = {
+ .name = "PNX Level IRQ",
+ .ack = mask_irq,
+ .mask = mask_irq,
+ .mask_ack = mask_irq,
+ .unmask = unmask_irq,
+};
+
+static struct irqaction gic_action = {
+ .handler = no_action,
+ .flags = IRQF_DISABLED,
+ .name = "GIC",
+};
+
+static struct irqaction timer_action = {
+ .handler = no_action,
+ .flags = IRQF_DISABLED,
+ .name = "Timer",
+};
+
+void __init arch_init_irq(void)
+{
+ int i;
+ int configPR;
+
+ for (i = 0; i < PNX8550_INT_CP0_TOTINT; i++) {
+ set_irq_chip_and_handler(i, &level_irq_type, handle_level_irq);
+ mask_irq(i); /* mask the irq just in case */
+ }
+
+ /* init of GIC/IPC interrupts */
+ /* should be done before cp0 since cp0 init enables the GIC int */
+ for (i = PNX8550_INT_GIC_MIN; i <= PNX8550_INT_GIC_MAX; i++) {
+ int gic_int_line = i - PNX8550_INT_GIC_MIN;
+ if (gic_int_line == 0 )
+ continue; // don't fiddle with int 0
+ /*
+ * enable change of TARGET, ENABLE and ACTIVE_LOW bits
+ * set TARGET 0 to route through hw0 interrupt
+ * set ACTIVE_LOW 0 active high (correct?)
+ *
+ * We really should setup an interrupt description table
+ * to do this nicely.
+ * Note, PCI INTA is active low on the bus, but inverted
+ * in the GIC, so to us it's active high.
+ */
+ PNX8550_GIC_REQ(i - PNX8550_INT_GIC_MIN) = 0x1E000000;
+
+ /* mask/priority is still 0 so we will not get any
+ * interrupts until it is unmasked */
+
+ set_irq_chip_and_handler(i, &level_irq_type, handle_level_irq);
+ }
+
+ /* Priority level 0 */
+ PNX8550_GIC_PRIMASK_0 = PNX8550_GIC_PRIMASK_1 = 0;
+
+ /* Set int vector table address */
+ PNX8550_GIC_VECTOR_0 = PNX8550_GIC_VECTOR_1 = 0;
+
+ set_irq_chip_and_handler(MIPS_CPU_GIC_IRQ, &level_irq_type,
+ handle_level_irq);
+ setup_irq(MIPS_CPU_GIC_IRQ, &gic_action);
+
+ /* init of Timer interrupts */
+ for (i = PNX8550_INT_TIMER_MIN; i <= PNX8550_INT_TIMER_MAX; i++)
+ set_irq_chip_and_handler(i, &level_irq_type, handle_level_irq);
+
+ /* Stop Timer 1-3 */
+ configPR = read_c0_config7();
+ configPR |= 0x00000038;
+ write_c0_config7(configPR);
+
+ set_irq_chip_and_handler(MIPS_CPU_TIMER_IRQ, &level_irq_type,
+ handle_level_irq);
+ setup_irq(MIPS_CPU_TIMER_IRQ, &timer_action);
+}
+
+EXPORT_SYMBOL(pnx8550_set_gic_priority);
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/Makefile linux-2.6.24.2/arch/mips/nxp/pnx8550/common/Makefile
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/Makefile 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/Makefile 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,29 @@
+#
+# Per Hallsmark, per.hallsmark@mvista.com
+#
+# ########################################################################
+#
+# This program is free software; you can distribute it and/or modify it
+# under the terms of the GNU General Public License (Version 2) as
+# published by the Free Software Foundation.
+#
+# This program is distributed in the hope it will be useful, but WITHOUT
+# ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+# FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+# for more details.
+#
+# You should have received a copy of the GNU General Public License along
+# with this program; if not, write to the Free Software Foundation, Inc.,
+# 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+#
+# #######################################################################
+#
+# Makefile for the PNX8550 specific kernel interface routines
+# under Linux.
+#
+
+obj-y := setup.o prom.o int.o reset.o time.o proc.o platform.o
+obj-$(CONFIG_PCI) += pci.o
+obj-$(CONFIG_KGDB) += gdb_hook.o
+
+EXTRA_CFLAGS += -Werror
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/pci.c linux-2.6.24.2/arch/mips/nxp/pnx8550/common/pci.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/pci.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/pci.c 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,133 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *
+ * Author: source@mvista.com
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <pci.h>
+#include <glb.h>
+#include <nand.h>
+
+static struct resource pci_io_resource = {
+ .start = PNX8550_PCIIO + 0x1000, /* reserve regacy I/O space */
+ .end = PNX8550_PCIIO + PNX8550_PCIIO_SIZE,
+ .name = "pci IO space",
+ .flags = IORESOURCE_IO
+};
+
+static struct resource pci_mem_resource = {
+ .start = PNX8550_PCIMEM,
+ .end = PNX8550_PCIMEM + PNX8550_PCIMEM_SIZE - 1,
+ .name = "pci memory space",
+ .flags = IORESOURCE_MEM
+};
+
+extern struct pci_ops pnx8550_pci_ops;
+
+static struct pci_controller pnx8550_controller = {
+ .pci_ops = &pnx8550_pci_ops,
+ .io_resource = &pci_io_resource,
+ .mem_resource = &pci_mem_resource,
+};
+
+/* Return the total size of DRAM-memory, (RANK0 + RANK1) */
+static inline unsigned long get_system_mem_size(void)
+{
+ /* Read IP2031_RANK0_ADDR_LO */
+ unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010);
+ /* Read IP2031_RANK1_ADDR_HI */
+ unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018);
+
+ return dram_r1_hi - dram_r0_lo + 1;
+}
+
+static int __init pnx8550_pci_setup(void)
+{
+ int pci_mem_code;
+ int mem_size = get_system_mem_size() >> 20;
+
+ /* Clear the Global 2 Register, PCI Inta Output Enable Registers
+ Bit 1:Enable DAC Powerdown
+ -> 0:DACs are enabled and are working normally
+ 1:DACs are powerdown
+ Bit 0:Enable of PCI inta output
+ -> 0 = Disable PCI inta output
+ 1 = Enable PCI inta output
+ */
+ PNX8550_GLB2_ENAB_INTA_O = 0;
+
+ /* Calc the PCI mem size code */
+ if (mem_size >= 128)
+ pci_mem_code = SIZE_128M;
+ else if (mem_size >= 64)
+ pci_mem_code = SIZE_64M;
+ else if (mem_size >= 32)
+ pci_mem_code = SIZE_32M;
+ else
+ pci_mem_code = SIZE_16M;
+
+ /* Set PCI_XIO registers */
+ outl(pci_mem_resource.start, PCI_BASE | PCI_BASE1_LO);
+ outl(pci_mem_resource.end + 1, PCI_BASE | PCI_BASE1_HI);
+ outl(pci_io_resource.start, PCI_BASE | PCI_BASE2_LO);
+ outl(pci_io_resource.end, PCI_BASE | PCI_BASE2_HI);
+
+ /* Send memory transaction via PCI_BASE2 */
+ outl(0x00000001, PCI_BASE | PCI_IO);
+
+ /* Unlock the setup register */
+ outl(0xca, PCI_BASE | PCI_UNLOCKREG);
+
+ /*
+ * BAR0 of PNX8550 (pci base 10) must be zero in order for ide
+ * to work, and in order for bus_to_baddr to work without any
+ * hacks.
+ */
+ outl(0x00000000, PCI_BASE | PCI_BASE10);
+
+ /*
+ *These two bars are set by default or the boot code.
+ * However, it's safer to set them here so we're not boot
+ * code dependent.
+ */
+ outl(0x1be00000, PCI_BASE | PCI_BASE14); /* PNX MMIO */
+ outl(PNX8550_NAND_BASE_ADDR, PCI_BASE | PCI_BASE18); /* XIO */
+
+ outl(PCI_EN_TA |
+ PCI_EN_PCI2MMI |
+ PCI_EN_XIO |
+ PCI_SETUP_BASE18_SIZE(SIZE_32M) |
+ PCI_SETUP_BASE18_EN |
+ PCI_SETUP_BASE14_EN |
+ PCI_SETUP_BASE10_PREF |
+ PCI_SETUP_BASE10_SIZE(pci_mem_code) |
+ PCI_SETUP_CFGMANAGE_EN |
+ PCI_SETUP_PCIARB_EN,
+ PCI_BASE |
+ PCI_SETUP); /* PCI_SETUP */
+ outl(0x00000000, PCI_BASE | PCI_CTRL); /* PCI_CONTROL */
+
+ register_pci_controller(&pnx8550_controller);
+
+ return 0;
+}
+
+arch_initcall(pnx8550_pci_setup);
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/platform.c linux-2.6.24.2/arch/mips/nxp/pnx8550/common/platform.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/platform.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/platform.c 2008-02-26 08:36:50.000000000 +0000
@@ -0,0 +1,132 @@
+/*
+ * Platform device support for NXP PNX8550 SoCs
+ *
+ * Copyright 2005, Embedded Alley Solutions, Inc
+ *
+ * Based on arch/mips/au1000/common/platform.c
+ * Platform device support for Au1x00 SoCs.
+ *
+ * Copyright 2004, Matt Porter <mporter@kernel.crashing.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/resource.h>
+#include <linux/serial.h>
+#include <linux/serial_pnx8xxx.h>
+#include <linux/platform_device.h>
+
+#include <int.h>
+#include <usb.h>
+#include <uart.h>
+
+static struct resource pnx8550_usb_ohci_resources[] = {
+ [0] = {
+ .start = PNX8550_USB_OHCI_OP_BASE,
+ .end = PNX8550_USB_OHCI_OP_BASE +
+ PNX8550_USB_OHCI_OP_LEN,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = PNX8550_INT_USB,
+ .end = PNX8550_INT_USB,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct resource pnx8550_uart_resources[] = {
+ [0] = {
+ .start = PNX8550_UART_PORT0,
+ .end = PNX8550_UART_PORT0 + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = PNX8550_UART_INT(0),
+ .end = PNX8550_UART_INT(0),
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = PNX8550_UART_PORT1,
+ .end = PNX8550_UART_PORT1 + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+ [3] = {
+ .start = PNX8550_UART_INT(1),
+ .end = PNX8550_UART_INT(1),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct pnx8xxx_port pnx8xxx_ports[] = {
+ [0] = {
+ .port = {
+ .type = PORT_PNX8XXX,
+ .iotype = UPIO_MEM,
+ .membase = (void __iomem *)PNX8550_UART_PORT0,
+ .mapbase = PNX8550_UART_PORT0,
+ .irq = PNX8550_UART_INT(0),
+ .uartclk = 3692300,
+ .fifosize = 16,
+ .flags = UPF_BOOT_AUTOCONF,
+ .line = 0,
+ },
+ },
+ [1] = {
+ .port = {
+ .type = PORT_PNX8XXX,
+ .iotype = UPIO_MEM,
+ .membase = (void __iomem *)PNX8550_UART_PORT1,
+ .mapbase = PNX8550_UART_PORT1,
+ .irq = PNX8550_UART_INT(1),
+ .uartclk = 3692300,
+ .fifosize = 16,
+ .flags = UPF_BOOT_AUTOCONF,
+ .line = 1,
+ },
+ },
+};
+
+/* The dmamask must be set for OHCI to work */
+static u64 ohci_dmamask = ~(u32)0;
+
+static u64 uart_dmamask = ~(u32)0;
+
+static struct platform_device pnx8550_usb_ohci_device = {
+ .name = "pnx8550-ohci",
+ .id = -1,
+ .dev = {
+ .dma_mask = &ohci_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .num_resources = ARRAY_SIZE(pnx8550_usb_ohci_resources),
+ .resource = pnx8550_usb_ohci_resources,
+};
+
+static struct platform_device pnx8550_uart_device = {
+ .name = "pnx8xxx-uart",
+ .id = -1,
+ .dev = {
+ .dma_mask = &uart_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ .platform_data = pnx8xxx_ports,
+ },
+ .num_resources = ARRAY_SIZE(pnx8550_uart_resources),
+ .resource = pnx8550_uart_resources,
+};
+
+static struct platform_device *pnx8550_platform_devices[] __initdata = {
+ &pnx8550_usb_ohci_device,
+ &pnx8550_uart_device,
+};
+
+static int __init pnx8550_platform_init(void)
+{
+ return platform_add_devices(pnx8550_platform_devices,
+ ARRAY_SIZE(pnx8550_platform_devices));
+}
+
+arch_initcall(pnx8550_platform_init);
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/proc.c linux-2.6.24.2/arch/mips/nxp/pnx8550/common/proc.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/proc.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/proc.c 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,112 @@
+/*
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ */
+#include <linux/init.h>
+#include <linux/proc_fs.h>
+#include <linux/irq.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/kernel_stat.h>
+#include <linux/random.h>
+
+#include <asm/io.h>
+#include <asm/gdb-stub.h>
+#include <int.h>
+#include <uart.h>
+
+
+static int pnx8550_timers_read(char* page, char** start, off_t offset, int count, int* eof, void* data)
+{
+ int len = 0;
+ int configPR = read_c0_config7();
+
+ if (offset==0) {
+ len += sprintf(&page[len], "Timer: count, compare, tc, status\n");
+ len += sprintf(&page[len], " 1: %11i, %8i, %1i, %s\n",
+ read_c0_count(), read_c0_compare(),
+ (configPR>>6)&0x1, ((configPR>>3)&0x1)? "off":"on");
+ len += sprintf(&page[len], " 2: %11i, %8i, %1i, %s\n",
+ read_c0_count2(), read_c0_compare2(),
+ (configPR>>7)&0x1, ((configPR>>4)&0x1)? "off":"on");
+ len += sprintf(&page[len], " 3: %11i, %8i, %1i, %s\n",
+ read_c0_count3(), read_c0_compare3(),
+ (configPR>>8)&0x1, ((configPR>>5)&0x1)? "off":"on");
+ }
+
+ return len;
+}
+
+static int pnx8550_registers_read(char* page, char** start, off_t offset, int count, int* eof, void* data)
+{
+ int len = 0;
+
+ if (offset==0) {
+ len += sprintf(&page[len], "config1: %#10.8x\n", read_c0_config1());
+ len += sprintf(&page[len], "config2: %#10.8x\n", read_c0_config2());
+ len += sprintf(&page[len], "config3: %#10.8x\n", read_c0_config3());
+ len += sprintf(&page[len], "configPR: %#10.8x\n", read_c0_config7());
+ len += sprintf(&page[len], "status: %#10.8x\n", read_c0_status());
+ len += sprintf(&page[len], "cause: %#10.8x\n", read_c0_cause());
+ len += sprintf(&page[len], "count: %#10.8x\n", read_c0_count());
+ len += sprintf(&page[len], "count_2: %#10.8x\n", read_c0_count2());
+ len += sprintf(&page[len], "count_3: %#10.8x\n", read_c0_count3());
+ len += sprintf(&page[len], "compare: %#10.8x\n", read_c0_compare());
+ len += sprintf(&page[len], "compare_2: %#10.8x\n", read_c0_compare2());
+ len += sprintf(&page[len], "compare_3: %#10.8x\n", read_c0_compare3());
+ }
+
+ return len;
+}
+
+static struct proc_dir_entry* pnx8550_dir = NULL;
+static struct proc_dir_entry* pnx8550_timers = NULL;
+static struct proc_dir_entry* pnx8550_registers = NULL;
+
+static int pnx8550_proc_init( void )
+{
+
+ // Create /proc/pnx8550
+ pnx8550_dir = proc_mkdir("pnx8550", NULL);
+ if (!pnx8550_dir) {
+ printk(KERN_ERR "Can't create pnx8550 proc dir\n");
+ return -1;
+ }
+
+ // Create /proc/pnx8550/timers
+ pnx8550_timers = create_proc_read_entry(
+ "timers",
+ 0,
+ pnx8550_dir,
+ pnx8550_timers_read,
+ NULL);
+
+ if (!pnx8550_timers)
+ printk(KERN_ERR "Can't create pnx8550 timers proc file\n");
+
+ // Create /proc/pnx8550/registers
+ pnx8550_registers = create_proc_read_entry(
+ "registers",
+ 0,
+ pnx8550_dir,
+ pnx8550_registers_read,
+ NULL);
+
+ if (!pnx8550_registers)
+ printk(KERN_ERR "Can't create pnx8550 registers proc file\n");
+
+ return 0;
+}
+
+__initcall(pnx8550_proc_init);
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/prom.c linux-2.6.24.2/arch/mips/nxp/pnx8550/common/prom.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/prom.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/prom.c 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,129 @@
+/*
+ *
+ * Per Hallsmark, per.hallsmark@mvista.com
+ *
+ * Based on jmr3927/common/prom.c
+ *
+ * 2004 (c) MontaVista Software, Inc. This file is licensed under the
+ * terms of the GNU General Public License version 2. This program is
+ * licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/string.h>
+#include <linux/serial_pnx8xxx.h>
+
+#include <asm/bootinfo.h>
+#include <uart.h>
+
+/* #define DEBUG_CMDLINE */
+
+extern int prom_argc;
+extern char **prom_argv, **prom_envp;
+
+typedef struct
+{
+ char *name;
+/* char *val; */
+}t_env_var;
+
+
+char * prom_getcmdline(void)
+{
+ return &(arcs_cmdline[0]);
+}
+
+void __init prom_init_cmdline(void)
+{
+ int i;
+
+ arcs_cmdline[0] = '\0';
+ for (i = 0; i < prom_argc; i++) {
+ strcat(arcs_cmdline, prom_argv[i]);
+ strcat(arcs_cmdline, " ");
+ }
+}
+
+char *prom_getenv(char *envname)
+{
+ /*
+ * Return a pointer to the given environment variable.
+ * Environment variables are stored in the form of "memsize=64".
+ */
+
+ t_env_var *env = (t_env_var *)prom_envp;
+ int i;
+
+ i = strlen(envname);
+
+ while(env->name) {
+ if(strncmp(envname, env->name, i) == 0) {
+ return(env->name + strlen(envname) + 1);
+ }
+ env++;
+ }
+ return(NULL);
+}
+
+inline unsigned char str2hexnum(unsigned char c)
+{
+ if(c >= '0' && c <= '9')
+ return c - '0';
+ if(c >= 'a' && c <= 'f')
+ return c - 'a' + 10;
+ if(c >= 'A' && c <= 'F')
+ return c - 'A' + 10;
+ return 0; /* foo */
+}
+
+inline void str2eaddr(unsigned char *ea, unsigned char *str)
+{
+ int i;
+
+ for(i = 0; i < 6; i++) {
+ unsigned char num;
+
+ if((*str == '.') || (*str == ':'))
+ str++;
+ num = str2hexnum(*str++) << 4;
+ num |= (str2hexnum(*str++));
+ ea[i] = num;
+ }
+}
+
+int get_ethernet_addr(char *ethernet_addr)
+{
+ char *ethaddr_str;
+
+ ethaddr_str = prom_getenv("ethaddr");
+ if (!ethaddr_str) {
+ printk("ethaddr not set in boot prom\n");
+ return -1;
+ }
+ str2eaddr(ethernet_addr, ethaddr_str);
+ return 0;
+}
+
+void __init prom_free_prom_memory(void)
+{
+}
+
+extern int pnx8550_console_port;
+
+/* used by early printk */
+void prom_putchar(char c)
+{
+ if (pnx8550_console_port != -1) {
+ /* Wait until FIFO not full */
+ while( ((ip3106_fifo(UART_BASE, pnx8550_console_port) & PNX8XXX_UART_FIFO_TXFIFO) >> 16) >= 16)
+ ;
+ /* Send one char */
+ ip3106_fifo(UART_BASE, pnx8550_console_port) = c;
+ }
+}
+
+EXPORT_SYMBOL(prom_getcmdline);
+EXPORT_SYMBOL(get_ethernet_addr);
+EXPORT_SYMBOL(str2eaddr);
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/reset.c linux-2.6.24.2/arch/mips/nxp/pnx8550/common/reset.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/reset.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/reset.c 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,49 @@
+/*.
+ *
+ * ########################################################################
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ *
+ * Reset the PNX8550 board.
+ *
+ */
+#include <linux/slab.h>
+#include <asm/reboot.h>
+#include <glb.h>
+
+void pnx8550_machine_restart(char *command)
+{
+ char head[] = "************* Machine restart *************";
+ char foot[] = "*******************************************";
+
+ printk("\n\n");
+ printk("%s\n", head);
+ if (command != NULL)
+ printk("* %s\n", command);
+ printk("%s\n", foot);
+
+ PNX8550_RST_CTL = PNX8550_RST_DO_SW_RST;
+}
+
+void pnx8550_machine_halt(void)
+{
+ printk("*** Machine halt. (Not implemented) ***\n");
+}
+
+void pnx8550_machine_power_off(void)
+{
+ printk("*** Machine power off. (Not implemented) ***\n");
+}
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/setup.c linux-2.6.24.2/arch/mips/nxp/pnx8550/common/setup.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/setup.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/setup.c 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,157 @@
+/*
+ *
+ * 2.6 port, Embedded Alley Solutions, Inc
+ *
+ * Based on Per Hallsmark, per.hallsmark@mvista.com
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ */
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/serial_pnx8xxx.h>
+#include <linux/pm.h>
+
+#include <asm/cpu.h>
+#include <asm/bootinfo.h>
+#include <asm/irq.h>
+#include <asm/mipsregs.h>
+#include <asm/reboot.h>
+#include <asm/pgtable.h>
+#include <asm/time.h>
+
+#include <glb.h>
+#include <int.h>
+#include <pci.h>
+#include <uart.h>
+#include <nand.h>
+
+extern void __init board_setup(void);
+extern void pnx8550_machine_restart(char *);
+extern void pnx8550_machine_halt(void);
+extern void pnx8550_machine_power_off(void);
+extern struct resource ioport_resource;
+extern struct resource iomem_resource;
+extern void rs_kgdb_hook(int tty_no);
+extern char *prom_getcmdline(void);
+
+struct resource standard_io_resources[] = {
+ {
+ .start = 0x00,
+ .end = 0x1f,
+ .name = "dma1",
+ .flags = IORESOURCE_BUSY
+ }, {
+ .start = 0x40,
+ .end = 0x5f,
+ .name = "timer",
+ .flags = IORESOURCE_BUSY
+ }, {
+ .start = 0x80,
+ .end = 0x8f,
+ .name = "dma page reg",
+ .flags = IORESOURCE_BUSY
+ }, {
+ .start = 0xc0,
+ .end = 0xdf,
+ .name = "dma2",
+ .flags = IORESOURCE_BUSY
+ },
+};
+
+#define STANDARD_IO_RESOURCES (sizeof(standard_io_resources)/sizeof(struct resource))
+
+extern struct resource pci_io_resource;
+extern struct resource pci_mem_resource;
+
+/* Return the total size of DRAM-memory, (RANK0 + RANK1) */
+unsigned long get_system_mem_size(void)
+{
+ /* Read IP2031_RANK0_ADDR_LO */
+ unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010);
+ /* Read IP2031_RANK1_ADDR_HI */
+ unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018);
+
+ return dram_r1_hi - dram_r0_lo + 1;
+}
+
+int pnx8550_console_port = -1;
+
+void __init plat_mem_setup(void)
+{
+ int i;
+ char* argptr;
+
+ board_setup(); /* board specific setup */
+
+ _machine_restart = pnx8550_machine_restart;
+ _machine_halt = pnx8550_machine_halt;
+ pm_power_off = pnx8550_machine_power_off;
+
+ /* Clear the Global 2 Register, PCI Inta Output Enable Registers
+ Bit 1:Enable DAC Powerdown
+ -> 0:DACs are enabled and are working normally
+ 1:DACs are powerdown
+ Bit 0:Enable of PCI inta output
+ -> 0 = Disable PCI inta output
+ 1 = Enable PCI inta output
+ */
+ PNX8550_GLB2_ENAB_INTA_O = 0;
+
+ /* IO/MEM resources. */
+ set_io_port_base(KSEG1);
+ ioport_resource.start = 0;
+ ioport_resource.end = ~0;
+ iomem_resource.start = 0;
+ iomem_resource.end = ~0;
+
+ /* Request I/O space for devices on this board */
+ for (i = 0; i < STANDARD_IO_RESOURCES; i++)
+ request_resource(&ioport_resource, standard_io_resources + i);
+
+ /* Place the Mode Control bit for GPIO pin 16 in primary function */
+ /* Pin 16 is used by UART1, UA1_TX */
+ outl((PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_16_BIT) |
+ (PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_17_BIT),
+ PNX8550_GPIO_MC1);
+
+ argptr = prom_getcmdline();
+ if ((argptr = strstr(argptr, "console=ttyS")) != NULL) {
+ argptr += strlen("console=ttyS");
+ pnx8550_console_port = *argptr == '0' ? 0 : 1;
+
+ /* We must initialize the UART (console) before early printk */
+ /* Set LCR to 8-bit and BAUD to 38400 (no 5) */
+ ip3106_lcr(UART_BASE, pnx8550_console_port) =
+ PNX8XXX_UART_LCR_8BIT;
+ ip3106_baud(UART_BASE, pnx8550_console_port) = 5;
+ }
+
+#ifdef CONFIG_KGDB
+ argptr = prom_getcmdline();
+ if ((argptr = strstr(argptr, "kgdb=ttyS")) != NULL) {
+ int line;
+ argptr += strlen("kgdb=ttyS");
+ line = *argptr == '0' ? 0 : 1;
+ rs_kgdb_hook(line);
+ pr_info("KGDB: Using ttyS%i for session, "
+ "please connect your debugger\n", line ? 1 : 0);
+ }
+#endif
+ return;
+}
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/time.c linux-2.6.24.2/arch/mips/nxp/pnx8550/common/time.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/common/time.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/common/time.c 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,163 @@
+/*
+ * Copyright 2001, 2002, 2003 MontaVista Software Inc.
+ * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
+ *
+ * Common time service routines for MIPS machines. See
+ * Documents/MIPS/README.txt.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/param.h>
+#include <linux/time.h>
+#include <linux/timer.h>
+#include <linux/smp.h>
+#include <linux/kernel_stat.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/time.h>
+#include <asm/hardirq.h>
+#include <asm/div64.h>
+#include <asm/debug.h>
+
+#include <int.h>
+#include <cm.h>
+
+static unsigned long cpj;
+
+static cycle_t hpt_read(void)
+{
+ return read_c0_count2();
+}
+
+static struct clocksource pnx_clocksource = {
+ .name = "pnx8xxx",
+ .rating = 200,
+ .read = hpt_read,
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static void timer_ack(void)
+{
+ write_c0_compare(cpj);
+}
+
+static irqreturn_t pnx8xxx_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *c = dev_id;
+
+ /* clear MATCH, signal the event */
+ c->event_handler(c);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction pnx8xxx_timer_irq = {
+ .handler = pnx8xxx_timer_interrupt,
+ .flags = IRQF_DISABLED | IRQF_PERCPU,
+ .name = "pnx8xxx_timer",
+};
+
+static irqreturn_t monotonic_interrupt(int irq, void *dev_id)
+{
+ /* Timer 2 clear interrupt */
+ write_c0_compare2(-1);
+ return IRQ_HANDLED;
+}
+
+static struct irqaction monotonic_irqaction = {
+ .handler = monotonic_interrupt,
+ .flags = IRQF_DISABLED,
+ .name = "Monotonic timer",
+};
+
+static int pnx8xxx_set_next_event(unsigned long delta,
+ struct clock_event_device *evt)
+{
+ write_c0_compare(delta);
+ return 0;
+}
+
+static struct clock_event_device pnx8xxx_clockevent = {
+ .name = "pnx8xxx_clockevent",
+ .features = CLOCK_EVT_FEAT_ONESHOT,
+ .set_next_event = pnx8xxx_set_next_event,
+};
+
+/*
+ * plat_time_init() - it does the following things:
+ *
+ * 1) plat_time_init() -
+ * a) (optional) set up RTC routines,
+ * b) (optional) calibrate and set the mips_hpt_frequency
+ * (only needed if you intended to use cpu counter as timer interrupt
+ * source)
+ */
+
+__init void plat_time_init(void)
+{
+ unsigned int configPR;
+ unsigned int n;
+ unsigned int m;
+ unsigned int p;
+ unsigned int pow2p;
+
+ clockevents_register_device(&pnx8xxx_clockevent);
+ clocksource_register(&pnx_clocksource);
+
+ setup_irq(PNX8550_INT_TIMER1, &pnx8xxx_timer_irq);
+ setup_irq(PNX8550_INT_TIMER2, &monotonic_irqaction);
+
+ /* Timer 1 start */
+ configPR = read_c0_config7();
+ configPR &= ~0x00000008;
+ write_c0_config7(configPR);
+
+ /* Timer 2 start */
+ configPR = read_c0_config7();
+ configPR &= ~0x00000010;
+ write_c0_config7(configPR);
+
+ /* Timer 3 stop */
+ configPR = read_c0_config7();
+ configPR |= 0x00000020;
+ write_c0_config7(configPR);
+
+
+ /* PLL0 sets MIPS clock (PLL1 <=> TM1, PLL6 <=> TM2, PLL5 <=> mem) */
+ /* (but only if CLK_MIPS_CTL select value [bits 3:1] is 1: FIXME) */
+
+ n = (PNX8550_CM_PLL0_CTL & PNX8550_CM_PLL_N_MASK) >> 16;
+ m = (PNX8550_CM_PLL0_CTL & PNX8550_CM_PLL_M_MASK) >> 8;
+ p = (PNX8550_CM_PLL0_CTL & PNX8550_CM_PLL_P_MASK) >> 2;
+ pow2p = (1 << p);
+
+ db_assert(m != 0 && pow2p != 0);
+
+ /*
+ * Compute the frequency as in the PNX8550 User Manual 1.0, p.186
+ * (a.k.a. 8-10). Divide by HZ for a timer offset that results in
+ * HZ timer interrupts per second.
+ */
+ mips_hpt_frequency = 27UL * ((1000000UL * n)/(m * pow2p));
+ cpj = (mips_hpt_frequency + HZ / 2) / HZ;
+ write_c0_count(0);
+ timer_ack();
+
+ /* Setup Timer 2 */
+ write_c0_count2(0);
+ write_c0_compare2(0xffffffff);
+
+}
+
+
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/jbs/board_setup.c linux-2.6.24.2/arch/mips/nxp/pnx8550/jbs/board_setup.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/jbs/board_setup.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/jbs/board_setup.c 2008-02-11 15:43:00.000000000 +0000
@@ -0,0 +1,65 @@
+/*
+ * JBS Specific board startup routines.
+ *
+ * Copyright 2005, Embedded Alley Solutions, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/console.h>
+#include <linux/mc146818rtc.h>
+#include <linux/delay.h>
+
+#include <asm/cpu.h>
+#include <asm/bootinfo.h>
+#include <asm/irq.h>
+#include <asm/mipsregs.h>
+#include <asm/reboot.h>
+#include <asm/pgtable.h>
+
+#include <glb.h>
+
+/* CP0 hazard avoidance. */
+#define BARRIER __asm__ __volatile__(".set noreorder\n\t" \
+ "nop; nop; nop; nop; nop; nop;\n\t" \
+ ".set reorder\n\t")
+
+void __init board_setup(void)
+{
+ unsigned long config0, configpr;
+
+ config0 = read_c0_config();
+
+ /* clear all three cache coherency fields */
+ config0 &= ~(0x7 | (7<<25) | (7<<28));
+ config0 |= (CONF_CM_DEFAULT | (CONF_CM_DEFAULT<<25) |
+ (CONF_CM_DEFAULT<<28));
+ write_c0_config(config0);
+ BARRIER;
+
+ configpr = read_c0_config7();
+ configpr |= (1<<19); /* enable tlb */
+ write_c0_config7(configpr);
+ BARRIER;
+}
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/jbs/init.c linux-2.6.24.2/arch/mips/nxp/pnx8550/jbs/init.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/jbs/init.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/jbs/init.c 2008-02-26 08:40:46.000000000 +0000
@@ -0,0 +1,56 @@
+/*
+ *
+ * Copyright 2005 Embedded Alley Solutions, Inc
+ * source@embeddedalley.com
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/sched.h>
+#include <linux/bootmem.h>
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <linux/string.h>
+#include <linux/kernel.h>
+
+int prom_argc;
+char **prom_argv, **prom_envp;
+extern void __init prom_init_cmdline(void);
+extern char *prom_getenv(char *envname);
+
+const char *get_system_type(void)
+{
+ return "NXP PNX8550/JBS";
+}
+
+void __init prom_init(void)
+{
+
+ unsigned long memsize;
+
+ mips_machtype = MACH_NXP_JBS;
+
+ //memsize = 0x02800000; /* Trimedia uses memory above */
+ memsize = 0x08000000; /* Trimedia uses memory above */
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/jbs/irqmap.c linux-2.6.24.2/arch/mips/nxp/pnx8550/jbs/irqmap.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/jbs/irqmap.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/jbs/irqmap.c 2008-02-26 08:37:14.000000000 +0000
@@ -0,0 +1,36 @@
+/*
+ * NXP JBS board irqmap.
+ *
+ * Copyright 2005 Embedded Alley Solutions, Inc
+ * source@embeddealley.com
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <int.h>
+
+char pnx8550_irq_tab[][5] __initdata = {
+ [8] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
+ [9] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
+ [17] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
+};
+
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/jbs/Makefile linux-2.6.24.2/arch/mips/nxp/pnx8550/jbs/Makefile
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/jbs/Makefile 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/jbs/Makefile 2008-02-26 08:36:56.000000000 +0000
@@ -0,0 +1,4 @@
+
+# Makefile for the NXP JBS Board.
+
+lib-y := init.o board_setup.o irqmap.o
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/stb810/board_setup.c linux-2.6.24.2/arch/mips/nxp/pnx8550/stb810/board_setup.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/stb810/board_setup.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/stb810/board_setup.c 2008-02-26 08:33:25.000000000 +0000
@@ -0,0 +1,49 @@
+/*
+ * STB810 specific board startup routines.
+ *
+ * Based on the arch/mips/nxp/pnx8550/jbs/board_setup.c
+ *
+ * Author: MontaVista Software, Inc.
+ * source@mvista.com
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/console.h>
+#include <linux/mc146818rtc.h>
+#include <linux/delay.h>
+
+#include <asm/cpu.h>
+#include <asm/bootinfo.h>
+#include <asm/irq.h>
+#include <asm/mipsregs.h>
+#include <asm/reboot.h>
+#include <asm/pgtable.h>
+
+#include <glb.h>
+
+void __init board_setup(void)
+{
+ unsigned long config0, configpr;
+
+ config0 = read_c0_config();
+
+ /* clear all three cache coherency fields */
+ config0 &= ~(0x7 | (7<<25) | (7<<28));
+ config0 |= (CONF_CM_DEFAULT | (CONF_CM_DEFAULT<<25) |
+ (CONF_CM_DEFAULT<<28));
+ write_c0_config(config0);
+
+ configpr = read_c0_config7();
+ configpr |= (1<<19); /* enable tlb */
+ write_c0_config7(configpr);
+}
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/stb810/irqmap.c linux-2.6.24.2/arch/mips/nxp/pnx8550/stb810/irqmap.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/stb810/irqmap.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/stb810/irqmap.c 2008-02-26 08:42:29.000000000 +0000
@@ -0,0 +1,23 @@
+/*
+ * NXP STB810 board irqmap.
+ *
+ * Author: MontaVista Software, Inc.
+ * source@mvista.com
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <int.h>
+
+char pnx8550_irq_tab[][5] __initdata = {
+ [8] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
+ [9] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
+ [10] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
+};
+
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/stb810/Makefile linux-2.6.24.2/arch/mips/nxp/pnx8550/stb810/Makefile
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/stb810/Makefile 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/stb810/Makefile 2008-02-26 08:37:19.000000000 +0000
@@ -0,0 +1,4 @@
+
+# Makefile for the NXP STB810 Board.
+
+lib-y := prom_init.o board_setup.o irqmap.o
diff -urN linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/stb810/prom_init.c linux-2.6.24.2/arch/mips/nxp/pnx8550/stb810/prom_init.c
--- linux-2.6.24.2.orig/arch/mips/nxp/pnx8550/stb810/prom_init.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.24.2/arch/mips/nxp/pnx8550/stb810/prom_init.c 2008-02-26 08:42:42.000000000 +0000
@@ -0,0 +1,48 @@
+/*
+ * STB810 specific prom routines
+ *
+ * Author: MontaVista Software, Inc.
+ * source@mvista.com
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/sched.h>
+#include <linux/bootmem.h>
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <linux/string.h>
+#include <linux/kernel.h>
+
+int prom_argc;
+char **prom_argv, **prom_envp;
+extern void __init prom_init_cmdline(void);
+extern char *prom_getenv(char *envname);
+
+const char *get_system_type(void)
+{
+ return "NXP PNX8950/STB810";
+}
+
+void __init prom_init(void)
+{
+ unsigned long memsize;
+
+ prom_argc = (int) fw_arg0;
+ prom_argv = (char **) fw_arg1;
+ prom_envp = (char **) fw_arg2;
+
+ prom_init_cmdline();
+
+ mips_machtype = MACH_NXP_STB810;
+
+ memsize = 0x08000000; /* Trimedia uses memory above */
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/gdb_hook.c linux-2.6.24.2/arch/mips/philips/pnx8550/common/gdb_hook.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/gdb_hook.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/gdb_hook.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,109 +0,0 @@
-/*
- * Carsten Langgaard, carstenl@mips.com
- * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- * This is the interface to the remote debugger stub.
- *
- */
-#include <linux/types.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/serial_reg.h>
-#include <linux/serial_ip3106.h>
-
-#include <asm/serial.h>
-#include <asm/io.h>
-
-#include <uart.h>
-
-static struct serial_state rs_table[IP3106_NR_PORTS] = {
-};
-static struct async_struct kdb_port_info = {0};
-
-void rs_kgdb_hook(int tty_no)
-{
- struct serial_state *ser = &rs_table[tty_no];
-
- kdb_port_info.state = ser;
- kdb_port_info.magic = SERIAL_MAGIC;
- kdb_port_info.port = tty_no;
- kdb_port_info.flags = ser->flags;
-
- /*
- * Clear all interrupts
- */
- /* Clear all the transmitter FIFO counters (pointer and status) */
- ip3106_lcr(UART_BASE, tty_no) |= IP3106_UART_LCR_TX_RST;
- /* Clear all the receiver FIFO counters (pointer and status) */
- ip3106_lcr(UART_BASE, tty_no) |= IP3106_UART_LCR_RX_RST;
- /* Clear all interrupts */
- ip3106_iclr(UART_BASE, tty_no) = IP3106_UART_INT_ALLRX |
- IP3106_UART_INT_ALLTX;
-
- /*
- * Now, initialize the UART
- */
- ip3106_lcr(UART_BASE, tty_no) = IP3106_UART_LCR_8BIT;
- ip3106_baud(UART_BASE, tty_no) = 5; // 38400 Baud
-}
-
-int putDebugChar(char c)
-{
- /* Wait until FIFO not full */
- while (((ip3106_fifo(UART_BASE, kdb_port_info.port) & IP3106_UART_FIFO_TXFIFO) >> 16) >= 16)
- ;
- /* Send one char */
- ip3106_fifo(UART_BASE, kdb_port_info.port) = c;
-
- return 1;
-}
-
-char getDebugChar(void)
-{
- char ch;
-
- /* Wait until there is a char in the FIFO */
- while (!((ip3106_fifo(UART_BASE, kdb_port_info.port) &
- IP3106_UART_FIFO_RXFIFO) >> 8))
- ;
- /* Read one char */
- ch = ip3106_fifo(UART_BASE, kdb_port_info.port) &
- IP3106_UART_FIFO_RBRTHR;
- /* Advance the RX FIFO read pointer */
- ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_RX_NEXT;
- return (ch);
-}
-
-void rs_disable_debug_interrupts(void)
-{
- ip3106_ien(UART_BASE, kdb_port_info.port) = 0; /* Disable all interrupts */
-}
-
-void rs_enable_debug_interrupts(void)
-{
- /* Clear all the transmitter FIFO counters (pointer and status) */
- ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_TX_RST;
- /* Clear all the receiver FIFO counters (pointer and status) */
- ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_RX_RST;
- /* Clear all interrupts */
- ip3106_iclr(UART_BASE, kdb_port_info.port) = IP3106_UART_INT_ALLRX |
- IP3106_UART_INT_ALLTX;
- ip3106_ien(UART_BASE, kdb_port_info.port) = IP3106_UART_INT_ALLRX; /* Enable RX interrupts */
-}
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/int.c linux-2.6.24.2/arch/mips/philips/pnx8550/common/int.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/int.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/int.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,238 +0,0 @@
-/*
- *
- * Copyright (C) 2005 Embedded Alley Solutions, Inc
- * Ported to 2.6.
- *
- * Per Hallsmark, per.hallsmark@mvista.com
- * Copyright (C) 2000, 2001 MIPS Technologies, Inc.
- * Copyright (C) 2001 Ralf Baechle
- *
- * Cleaned up and bug fixing: Pete Popov, ppopov@embeddedalley.com
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- */
-#include <linux/compiler.h>
-#include <linux/init.h>
-#include <linux/irq.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/kernel_stat.h>
-#include <linux/random.h>
-#include <linux/module.h>
-
-#include <asm/io.h>
-#include <asm/gdb-stub.h>
-#include <int.h>
-#include <uart.h>
-
-/* default prio for interrupts */
-/* first one is a no-no so therefore always prio 0 (disabled) */
-static char gic_prio[PNX8550_INT_GIC_TOTINT] = {
- 0, 1, 1, 1, 1, 15, 1, 1, 1, 1, // 0 - 9
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 10 - 19
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 20 - 29
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 30 - 39
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 40 - 49
- 1, 1, 1, 1, 1, 1, 1, 1, 2, 1, // 50 - 59
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, // 60 - 69
- 1 // 70
-};
-
-static void hw0_irqdispatch(int irq)
-{
- /* find out which interrupt */
- irq = PNX8550_GIC_VECTOR_0 >> 3;
-
- if (irq == 0) {
- printk("hw0_irqdispatch: irq 0, spurious interrupt?\n");
- return;
- }
- do_IRQ(PNX8550_INT_GIC_MIN + irq);
-}
-
-
-static void timer_irqdispatch(int irq)
-{
- irq = (0x01c0 & read_c0_config7()) >> 6;
-
- if (unlikely(irq == 0)) {
- printk("timer_irqdispatch: irq 0, spurious interrupt?\n");
- return;
- }
-
- if (irq & 0x1)
- do_IRQ(PNX8550_INT_TIMER1);
- if (irq & 0x2)
- do_IRQ(PNX8550_INT_TIMER2);
- if (irq & 0x4)
- do_IRQ(PNX8550_INT_TIMER3);
-}
-
-asmlinkage void plat_irq_dispatch(void)
-{
- unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM;
-
- if (pending & STATUSF_IP2)
- hw0_irqdispatch(2);
- else if (pending & STATUSF_IP7) {
- if (read_c0_config7() & 0x01c0)
- timer_irqdispatch(7);
- } else
- spurious_interrupt();
-}
-
-static inline void modify_cp0_intmask(unsigned clr_mask, unsigned set_mask)
-{
- unsigned long status = read_c0_status();
-
- status &= ~((clr_mask & 0xFF) << 8);
- status |= (set_mask & 0xFF) << 8;
-
- write_c0_status(status);
-}
-
-static inline void mask_gic_int(unsigned int irq_nr)
-{
- /* interrupt disabled, bit 26(WE_ENABLE)=1 and bit 16(enable)=0 */
- PNX8550_GIC_REQ(irq_nr) = 1<<28; /* set priority to 0 */
-}
-
-static inline void unmask_gic_int(unsigned int irq_nr)
-{
- /* set prio mask to lower four bits and enable interrupt */
- PNX8550_GIC_REQ(irq_nr) = (1<<26 | 1<<16) | (1<<28) | gic_prio[irq_nr];
-}
-
-static inline void mask_irq(unsigned int irq_nr)
-{
- if ((PNX8550_INT_CP0_MIN <= irq_nr) && (irq_nr <= PNX8550_INT_CP0_MAX)) {
- modify_cp0_intmask(1 << irq_nr, 0);
- } else if ((PNX8550_INT_GIC_MIN <= irq_nr) &&
- (irq_nr <= PNX8550_INT_GIC_MAX)) {
- mask_gic_int(irq_nr - PNX8550_INT_GIC_MIN);
- } else if ((PNX8550_INT_TIMER_MIN <= irq_nr) &&
- (irq_nr <= PNX8550_INT_TIMER_MAX)) {
- modify_cp0_intmask(1 << 7, 0);
- } else {
- printk("mask_irq: irq %d doesn't exist!\n", irq_nr);
- }
-}
-
-static inline void unmask_irq(unsigned int irq_nr)
-{
- if ((PNX8550_INT_CP0_MIN <= irq_nr) && (irq_nr <= PNX8550_INT_CP0_MAX)) {
- modify_cp0_intmask(0, 1 << irq_nr);
- } else if ((PNX8550_INT_GIC_MIN <= irq_nr) &&
- (irq_nr <= PNX8550_INT_GIC_MAX)) {
- unmask_gic_int(irq_nr - PNX8550_INT_GIC_MIN);
- } else if ((PNX8550_INT_TIMER_MIN <= irq_nr) &&
- (irq_nr <= PNX8550_INT_TIMER_MAX)) {
- modify_cp0_intmask(0, 1 << 7);
- } else {
- printk("mask_irq: irq %d doesn't exist!\n", irq_nr);
- }
-}
-
-int pnx8550_set_gic_priority(int irq, int priority)
-{
- int gic_irq = irq-PNX8550_INT_GIC_MIN;
- int prev_priority = PNX8550_GIC_REQ(gic_irq) & 0xf;
-
- gic_prio[gic_irq] = priority;
- PNX8550_GIC_REQ(gic_irq) |= (0x10000000 | gic_prio[gic_irq]);
-
- return prev_priority;
-}
-
-static struct irq_chip level_irq_type = {
- .name = "PNX Level IRQ",
- .ack = mask_irq,
- .mask = mask_irq,
- .mask_ack = mask_irq,
- .unmask = unmask_irq,
-};
-
-static struct irqaction gic_action = {
- .handler = no_action,
- .flags = IRQF_DISABLED,
- .name = "GIC",
-};
-
-static struct irqaction timer_action = {
- .handler = no_action,
- .flags = IRQF_DISABLED,
- .name = "Timer",
-};
-
-void __init arch_init_irq(void)
-{
- int i;
- int configPR;
-
- for (i = 0; i < PNX8550_INT_CP0_TOTINT; i++) {
- set_irq_chip_and_handler(i, &level_irq_type, handle_level_irq);
- mask_irq(i); /* mask the irq just in case */
- }
-
- /* init of GIC/IPC interrupts */
- /* should be done before cp0 since cp0 init enables the GIC int */
- for (i = PNX8550_INT_GIC_MIN; i <= PNX8550_INT_GIC_MAX; i++) {
- int gic_int_line = i - PNX8550_INT_GIC_MIN;
- if (gic_int_line == 0 )
- continue; // don't fiddle with int 0
- /*
- * enable change of TARGET, ENABLE and ACTIVE_LOW bits
- * set TARGET 0 to route through hw0 interrupt
- * set ACTIVE_LOW 0 active high (correct?)
- *
- * We really should setup an interrupt description table
- * to do this nicely.
- * Note, PCI INTA is active low on the bus, but inverted
- * in the GIC, so to us it's active high.
- */
- PNX8550_GIC_REQ(i - PNX8550_INT_GIC_MIN) = 0x1E000000;
-
- /* mask/priority is still 0 so we will not get any
- * interrupts until it is unmasked */
-
- set_irq_chip_and_handler(i, &level_irq_type, handle_level_irq);
- }
-
- /* Priority level 0 */
- PNX8550_GIC_PRIMASK_0 = PNX8550_GIC_PRIMASK_1 = 0;
-
- /* Set int vector table address */
- PNX8550_GIC_VECTOR_0 = PNX8550_GIC_VECTOR_1 = 0;
-
- set_irq_chip_and_handler(MIPS_CPU_GIC_IRQ, &level_irq_type,
- handle_level_irq);
- setup_irq(MIPS_CPU_GIC_IRQ, &gic_action);
-
- /* init of Timer interrupts */
- for (i = PNX8550_INT_TIMER_MIN; i <= PNX8550_INT_TIMER_MAX; i++)
- set_irq_chip_and_handler(i, &level_irq_type, handle_level_irq);
-
- /* Stop Timer 1-3 */
- configPR = read_c0_config7();
- configPR |= 0x00000038;
- write_c0_config7(configPR);
-
- set_irq_chip_and_handler(MIPS_CPU_TIMER_IRQ, &level_irq_type,
- handle_level_irq);
- setup_irq(MIPS_CPU_TIMER_IRQ, &timer_action);
-}
-
-EXPORT_SYMBOL(pnx8550_set_gic_priority);
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/Makefile linux-2.6.24.2/arch/mips/philips/pnx8550/common/Makefile
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/Makefile 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/Makefile 1970-01-01 01:00:00.000000000 +0100
@@ -1,29 +0,0 @@
-#
-# Per Hallsmark, per.hallsmark@mvista.com
-#
-# ########################################################################
-#
-# This program is free software; you can distribute it and/or modify it
-# under the terms of the GNU General Public License (Version 2) as
-# published by the Free Software Foundation.
-#
-# This program is distributed in the hope it will be useful, but WITHOUT
-# ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-# FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-# for more details.
-#
-# You should have received a copy of the GNU General Public License along
-# with this program; if not, write to the Free Software Foundation, Inc.,
-# 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-#
-# #######################################################################
-#
-# Makefile for the PNX8550 specific kernel interface routines
-# under Linux.
-#
-
-obj-y := setup.o prom.o int.o reset.o time.o proc.o platform.o
-obj-$(CONFIG_PCI) += pci.o
-obj-$(CONFIG_KGDB) += gdb_hook.o
-
-EXTRA_CFLAGS += -Werror
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/pci.c linux-2.6.24.2/arch/mips/philips/pnx8550/common/pci.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/pci.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/pci.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,133 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- *
- * Author: source@mvista.com
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-#include <pci.h>
-#include <glb.h>
-#include <nand.h>
-
-static struct resource pci_io_resource = {
- .start = PNX8550_PCIIO + 0x1000, /* reserve regacy I/O space */
- .end = PNX8550_PCIIO + PNX8550_PCIIO_SIZE,
- .name = "pci IO space",
- .flags = IORESOURCE_IO
-};
-
-static struct resource pci_mem_resource = {
- .start = PNX8550_PCIMEM,
- .end = PNX8550_PCIMEM + PNX8550_PCIMEM_SIZE - 1,
- .name = "pci memory space",
- .flags = IORESOURCE_MEM
-};
-
-extern struct pci_ops pnx8550_pci_ops;
-
-static struct pci_controller pnx8550_controller = {
- .pci_ops = &pnx8550_pci_ops,
- .io_resource = &pci_io_resource,
- .mem_resource = &pci_mem_resource,
-};
-
-/* Return the total size of DRAM-memory, (RANK0 + RANK1) */
-static inline unsigned long get_system_mem_size(void)
-{
- /* Read IP2031_RANK0_ADDR_LO */
- unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010);
- /* Read IP2031_RANK1_ADDR_HI */
- unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018);
-
- return dram_r1_hi - dram_r0_lo + 1;
-}
-
-static int __init pnx8550_pci_setup(void)
-{
- int pci_mem_code;
- int mem_size = get_system_mem_size() >> 20;
-
- /* Clear the Global 2 Register, PCI Inta Output Enable Registers
- Bit 1:Enable DAC Powerdown
- -> 0:DACs are enabled and are working normally
- 1:DACs are powerdown
- Bit 0:Enable of PCI inta output
- -> 0 = Disable PCI inta output
- 1 = Enable PCI inta output
- */
- PNX8550_GLB2_ENAB_INTA_O = 0;
-
- /* Calc the PCI mem size code */
- if (mem_size >= 128)
- pci_mem_code = SIZE_128M;
- else if (mem_size >= 64)
- pci_mem_code = SIZE_64M;
- else if (mem_size >= 32)
- pci_mem_code = SIZE_32M;
- else
- pci_mem_code = SIZE_16M;
-
- /* Set PCI_XIO registers */
- outl(pci_mem_resource.start, PCI_BASE | PCI_BASE1_LO);
- outl(pci_mem_resource.end + 1, PCI_BASE | PCI_BASE1_HI);
- outl(pci_io_resource.start, PCI_BASE | PCI_BASE2_LO);
- outl(pci_io_resource.end, PCI_BASE | PCI_BASE2_HI);
-
- /* Send memory transaction via PCI_BASE2 */
- outl(0x00000001, PCI_BASE | PCI_IO);
-
- /* Unlock the setup register */
- outl(0xca, PCI_BASE | PCI_UNLOCKREG);
-
- /*
- * BAR0 of PNX8550 (pci base 10) must be zero in order for ide
- * to work, and in order for bus_to_baddr to work without any
- * hacks.
- */
- outl(0x00000000, PCI_BASE | PCI_BASE10);
-
- /*
- *These two bars are set by default or the boot code.
- * However, it's safer to set them here so we're not boot
- * code dependent.
- */
- outl(0x1be00000, PCI_BASE | PCI_BASE14); /* PNX MMIO */
- outl(PNX8550_NAND_BASE_ADDR, PCI_BASE | PCI_BASE18); /* XIO */
-
- outl(PCI_EN_TA |
- PCI_EN_PCI2MMI |
- PCI_EN_XIO |
- PCI_SETUP_BASE18_SIZE(SIZE_32M) |
- PCI_SETUP_BASE18_EN |
- PCI_SETUP_BASE14_EN |
- PCI_SETUP_BASE10_PREF |
- PCI_SETUP_BASE10_SIZE(pci_mem_code) |
- PCI_SETUP_CFGMANAGE_EN |
- PCI_SETUP_PCIARB_EN,
- PCI_BASE |
- PCI_SETUP); /* PCI_SETUP */
- outl(0x00000000, PCI_BASE | PCI_CTRL); /* PCI_CONTROL */
-
- register_pci_controller(&pnx8550_controller);
-
- return 0;
-}
-
-arch_initcall(pnx8550_pci_setup);
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/platform.c linux-2.6.24.2/arch/mips/philips/pnx8550/common/platform.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/platform.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/platform.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,132 +0,0 @@
-/*
- * Platform device support for Philips PNX8550 SoCs
- *
- * Copyright 2005, Embedded Alley Solutions, Inc
- *
- * Based on arch/mips/au1000/common/platform.c
- * Platform device support for Au1x00 SoCs.
- *
- * Copyright 2004, Matt Porter <mporter@kernel.crashing.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <linux/device.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/resource.h>
-#include <linux/serial.h>
-#include <linux/serial_pnx8xxx.h>
-#include <linux/platform_device.h>
-
-#include <int.h>
-#include <usb.h>
-#include <uart.h>
-
-static struct resource pnx8550_usb_ohci_resources[] = {
- [0] = {
- .start = PNX8550_USB_OHCI_OP_BASE,
- .end = PNX8550_USB_OHCI_OP_BASE +
- PNX8550_USB_OHCI_OP_LEN,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = PNX8550_INT_USB,
- .end = PNX8550_INT_USB,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource pnx8550_uart_resources[] = {
- [0] = {
- .start = PNX8550_UART_PORT0,
- .end = PNX8550_UART_PORT0 + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = PNX8550_UART_INT(0),
- .end = PNX8550_UART_INT(0),
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = PNX8550_UART_PORT1,
- .end = PNX8550_UART_PORT1 + 0xfff,
- .flags = IORESOURCE_MEM,
- },
- [3] = {
- .start = PNX8550_UART_INT(1),
- .end = PNX8550_UART_INT(1),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct pnx8xxx_port pnx8xxx_ports[] = {
- [0] = {
- .port = {
- .type = PORT_PNX8XXX,
- .iotype = UPIO_MEM,
- .membase = (void __iomem *)PNX8550_UART_PORT0,
- .mapbase = PNX8550_UART_PORT0,
- .irq = PNX8550_UART_INT(0),
- .uartclk = 3692300,
- .fifosize = 16,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- },
- [1] = {
- .port = {
- .type = PORT_PNX8XXX,
- .iotype = UPIO_MEM,
- .membase = (void __iomem *)PNX8550_UART_PORT1,
- .mapbase = PNX8550_UART_PORT1,
- .irq = PNX8550_UART_INT(1),
- .uartclk = 3692300,
- .fifosize = 16,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- },
-};
-
-/* The dmamask must be set for OHCI to work */
-static u64 ohci_dmamask = ~(u32)0;
-
-static u64 uart_dmamask = ~(u32)0;
-
-static struct platform_device pnx8550_usb_ohci_device = {
- .name = "pnx8550-ohci",
- .id = -1,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = 0xffffffff,
- },
- .num_resources = ARRAY_SIZE(pnx8550_usb_ohci_resources),
- .resource = pnx8550_usb_ohci_resources,
-};
-
-static struct platform_device pnx8550_uart_device = {
- .name = "pnx8xxx-uart",
- .id = -1,
- .dev = {
- .dma_mask = &uart_dmamask,
- .coherent_dma_mask = 0xffffffff,
- .platform_data = pnx8xxx_ports,
- },
- .num_resources = ARRAY_SIZE(pnx8550_uart_resources),
- .resource = pnx8550_uart_resources,
-};
-
-static struct platform_device *pnx8550_platform_devices[] __initdata = {
- &pnx8550_usb_ohci_device,
- &pnx8550_uart_device,
-};
-
-static int __init pnx8550_platform_init(void)
-{
- return platform_add_devices(pnx8550_platform_devices,
- ARRAY_SIZE(pnx8550_platform_devices));
-}
-
-arch_initcall(pnx8550_platform_init);
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/proc.c linux-2.6.24.2/arch/mips/philips/pnx8550/common/proc.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/proc.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/proc.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,112 +0,0 @@
-/*
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/init.h>
-#include <linux/proc_fs.h>
-#include <linux/irq.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/kernel_stat.h>
-#include <linux/random.h>
-
-#include <asm/io.h>
-#include <asm/gdb-stub.h>
-#include <int.h>
-#include <uart.h>
-
-
-static int pnx8550_timers_read(char* page, char** start, off_t offset, int count, int* eof, void* data)
-{
- int len = 0;
- int configPR = read_c0_config7();
-
- if (offset==0) {
- len += sprintf(&page[len], "Timer: count, compare, tc, status\n");
- len += sprintf(&page[len], " 1: %11i, %8i, %1i, %s\n",
- read_c0_count(), read_c0_compare(),
- (configPR>>6)&0x1, ((configPR>>3)&0x1)? "off":"on");
- len += sprintf(&page[len], " 2: %11i, %8i, %1i, %s\n",
- read_c0_count2(), read_c0_compare2(),
- (configPR>>7)&0x1, ((configPR>>4)&0x1)? "off":"on");
- len += sprintf(&page[len], " 3: %11i, %8i, %1i, %s\n",
- read_c0_count3(), read_c0_compare3(),
- (configPR>>8)&0x1, ((configPR>>5)&0x1)? "off":"on");
- }
-
- return len;
-}
-
-static int pnx8550_registers_read(char* page, char** start, off_t offset, int count, int* eof, void* data)
-{
- int len = 0;
-
- if (offset==0) {
- len += sprintf(&page[len], "config1: %#10.8x\n", read_c0_config1());
- len += sprintf(&page[len], "config2: %#10.8x\n", read_c0_config2());
- len += sprintf(&page[len], "config3: %#10.8x\n", read_c0_config3());
- len += sprintf(&page[len], "configPR: %#10.8x\n", read_c0_config7());
- len += sprintf(&page[len], "status: %#10.8x\n", read_c0_status());
- len += sprintf(&page[len], "cause: %#10.8x\n", read_c0_cause());
- len += sprintf(&page[len], "count: %#10.8x\n", read_c0_count());
- len += sprintf(&page[len], "count_2: %#10.8x\n", read_c0_count2());
- len += sprintf(&page[len], "count_3: %#10.8x\n", read_c0_count3());
- len += sprintf(&page[len], "compare: %#10.8x\n", read_c0_compare());
- len += sprintf(&page[len], "compare_2: %#10.8x\n", read_c0_compare2());
- len += sprintf(&page[len], "compare_3: %#10.8x\n", read_c0_compare3());
- }
-
- return len;
-}
-
-static struct proc_dir_entry* pnx8550_dir = NULL;
-static struct proc_dir_entry* pnx8550_timers = NULL;
-static struct proc_dir_entry* pnx8550_registers = NULL;
-
-static int pnx8550_proc_init( void )
-{
-
- // Create /proc/pnx8550
- pnx8550_dir = proc_mkdir("pnx8550", NULL);
- if (!pnx8550_dir) {
- printk(KERN_ERR "Can't create pnx8550 proc dir\n");
- return -1;
- }
-
- // Create /proc/pnx8550/timers
- pnx8550_timers = create_proc_read_entry(
- "timers",
- 0,
- pnx8550_dir,
- pnx8550_timers_read,
- NULL);
-
- if (!pnx8550_timers)
- printk(KERN_ERR "Can't create pnx8550 timers proc file\n");
-
- // Create /proc/pnx8550/registers
- pnx8550_registers = create_proc_read_entry(
- "registers",
- 0,
- pnx8550_dir,
- pnx8550_registers_read,
- NULL);
-
- if (!pnx8550_registers)
- printk(KERN_ERR "Can't create pnx8550 registers proc file\n");
-
- return 0;
-}
-
-__initcall(pnx8550_proc_init);
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/prom.c linux-2.6.24.2/arch/mips/philips/pnx8550/common/prom.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/prom.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/prom.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,129 +0,0 @@
-/*
- *
- * Per Hallsmark, per.hallsmark@mvista.com
- *
- * Based on jmr3927/common/prom.c
- *
- * 2004 (c) MontaVista Software, Inc. This file is licensed under the
- * terms of the GNU General Public License version 2. This program is
- * licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/serial_pnx8xxx.h>
-
-#include <asm/bootinfo.h>
-#include <uart.h>
-
-/* #define DEBUG_CMDLINE */
-
-extern int prom_argc;
-extern char **prom_argv, **prom_envp;
-
-typedef struct
-{
- char *name;
-/* char *val; */
-}t_env_var;
-
-
-char * prom_getcmdline(void)
-{
- return &(arcs_cmdline[0]);
-}
-
-void __init prom_init_cmdline(void)
-{
- int i;
-
- arcs_cmdline[0] = '\0';
- for (i = 0; i < prom_argc; i++) {
- strcat(arcs_cmdline, prom_argv[i]);
- strcat(arcs_cmdline, " ");
- }
-}
-
-char *prom_getenv(char *envname)
-{
- /*
- * Return a pointer to the given environment variable.
- * Environment variables are stored in the form of "memsize=64".
- */
-
- t_env_var *env = (t_env_var *)prom_envp;
- int i;
-
- i = strlen(envname);
-
- while(env->name) {
- if(strncmp(envname, env->name, i) == 0) {
- return(env->name + strlen(envname) + 1);
- }
- env++;
- }
- return(NULL);
-}
-
-inline unsigned char str2hexnum(unsigned char c)
-{
- if(c >= '0' && c <= '9')
- return c - '0';
- if(c >= 'a' && c <= 'f')
- return c - 'a' + 10;
- if(c >= 'A' && c <= 'F')
- return c - 'A' + 10;
- return 0; /* foo */
-}
-
-inline void str2eaddr(unsigned char *ea, unsigned char *str)
-{
- int i;
-
- for(i = 0; i < 6; i++) {
- unsigned char num;
-
- if((*str == '.') || (*str == ':'))
- str++;
- num = str2hexnum(*str++) << 4;
- num |= (str2hexnum(*str++));
- ea[i] = num;
- }
-}
-
-int get_ethernet_addr(char *ethernet_addr)
-{
- char *ethaddr_str;
-
- ethaddr_str = prom_getenv("ethaddr");
- if (!ethaddr_str) {
- printk("ethaddr not set in boot prom\n");
- return -1;
- }
- str2eaddr(ethernet_addr, ethaddr_str);
- return 0;
-}
-
-void __init prom_free_prom_memory(void)
-{
-}
-
-extern int pnx8550_console_port;
-
-/* used by early printk */
-void prom_putchar(char c)
-{
- if (pnx8550_console_port != -1) {
- /* Wait until FIFO not full */
- while( ((ip3106_fifo(UART_BASE, pnx8550_console_port) & PNX8XXX_UART_FIFO_TXFIFO) >> 16) >= 16)
- ;
- /* Send one char */
- ip3106_fifo(UART_BASE, pnx8550_console_port) = c;
- }
-}
-
-EXPORT_SYMBOL(prom_getcmdline);
-EXPORT_SYMBOL(get_ethernet_addr);
-EXPORT_SYMBOL(str2eaddr);
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/reset.c linux-2.6.24.2/arch/mips/philips/pnx8550/common/reset.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/reset.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/reset.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,49 +0,0 @@
-/*.
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- * Reset the PNX8550 board.
- *
- */
-#include <linux/slab.h>
-#include <asm/reboot.h>
-#include <glb.h>
-
-void pnx8550_machine_restart(char *command)
-{
- char head[] = "************* Machine restart *************";
- char foot[] = "*******************************************";
-
- printk("\n\n");
- printk("%s\n", head);
- if (command != NULL)
- printk("* %s\n", command);
- printk("%s\n", foot);
-
- PNX8550_RST_CTL = PNX8550_RST_DO_SW_RST;
-}
-
-void pnx8550_machine_halt(void)
-{
- printk("*** Machine halt. (Not implemented) ***\n");
-}
-
-void pnx8550_machine_power_off(void)
-{
- printk("*** Machine power off. (Not implemented) ***\n");
-}
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/setup.c linux-2.6.24.2/arch/mips/philips/pnx8550/common/setup.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/setup.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/setup.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,157 +0,0 @@
-/*
- *
- * 2.6 port, Embedded Alley Solutions, Inc
- *
- * Based on Per Hallsmark, per.hallsmark@mvista.com
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/ioport.h>
-#include <linux/irq.h>
-#include <linux/mm.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/serial_pnx8xxx.h>
-#include <linux/pm.h>
-
-#include <asm/cpu.h>
-#include <asm/bootinfo.h>
-#include <asm/irq.h>
-#include <asm/mipsregs.h>
-#include <asm/reboot.h>
-#include <asm/pgtable.h>
-#include <asm/time.h>
-
-#include <glb.h>
-#include <int.h>
-#include <pci.h>
-#include <uart.h>
-#include <nand.h>
-
-extern void __init board_setup(void);
-extern void pnx8550_machine_restart(char *);
-extern void pnx8550_machine_halt(void);
-extern void pnx8550_machine_power_off(void);
-extern struct resource ioport_resource;
-extern struct resource iomem_resource;
-extern void rs_kgdb_hook(int tty_no);
-extern char *prom_getcmdline(void);
-
-struct resource standard_io_resources[] = {
- {
- .start = 0x00,
- .end = 0x1f,
- .name = "dma1",
- .flags = IORESOURCE_BUSY
- }, {
- .start = 0x40,
- .end = 0x5f,
- .name = "timer",
- .flags = IORESOURCE_BUSY
- }, {
- .start = 0x80,
- .end = 0x8f,
- .name = "dma page reg",
- .flags = IORESOURCE_BUSY
- }, {
- .start = 0xc0,
- .end = 0xdf,
- .name = "dma2",
- .flags = IORESOURCE_BUSY
- },
-};
-
-#define STANDARD_IO_RESOURCES (sizeof(standard_io_resources)/sizeof(struct resource))
-
-extern struct resource pci_io_resource;
-extern struct resource pci_mem_resource;
-
-/* Return the total size of DRAM-memory, (RANK0 + RANK1) */
-unsigned long get_system_mem_size(void)
-{
- /* Read IP2031_RANK0_ADDR_LO */
- unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010);
- /* Read IP2031_RANK1_ADDR_HI */
- unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018);
-
- return dram_r1_hi - dram_r0_lo + 1;
-}
-
-int pnx8550_console_port = -1;
-
-void __init plat_mem_setup(void)
-{
- int i;
- char* argptr;
-
- board_setup(); /* board specific setup */
-
- _machine_restart = pnx8550_machine_restart;
- _machine_halt = pnx8550_machine_halt;
- pm_power_off = pnx8550_machine_power_off;
-
- /* Clear the Global 2 Register, PCI Inta Output Enable Registers
- Bit 1:Enable DAC Powerdown
- -> 0:DACs are enabled and are working normally
- 1:DACs are powerdown
- Bit 0:Enable of PCI inta output
- -> 0 = Disable PCI inta output
- 1 = Enable PCI inta output
- */
- PNX8550_GLB2_ENAB_INTA_O = 0;
-
- /* IO/MEM resources. */
- set_io_port_base(KSEG1);
- ioport_resource.start = 0;
- ioport_resource.end = ~0;
- iomem_resource.start = 0;
- iomem_resource.end = ~0;
-
- /* Request I/O space for devices on this board */
- for (i = 0; i < STANDARD_IO_RESOURCES; i++)
- request_resource(&ioport_resource, standard_io_resources + i);
-
- /* Place the Mode Control bit for GPIO pin 16 in primary function */
- /* Pin 16 is used by UART1, UA1_TX */
- outl((PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_16_BIT) |
- (PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_17_BIT),
- PNX8550_GPIO_MC1);
-
- argptr = prom_getcmdline();
- if ((argptr = strstr(argptr, "console=ttyS")) != NULL) {
- argptr += strlen("console=ttyS");
- pnx8550_console_port = *argptr == '0' ? 0 : 1;
-
- /* We must initialize the UART (console) before early printk */
- /* Set LCR to 8-bit and BAUD to 38400 (no 5) */
- ip3106_lcr(UART_BASE, pnx8550_console_port) =
- PNX8XXX_UART_LCR_8BIT;
- ip3106_baud(UART_BASE, pnx8550_console_port) = 5;
- }
-
-#ifdef CONFIG_KGDB
- argptr = prom_getcmdline();
- if ((argptr = strstr(argptr, "kgdb=ttyS")) != NULL) {
- int line;
- argptr += strlen("kgdb=ttyS");
- line = *argptr == '0' ? 0 : 1;
- rs_kgdb_hook(line);
- pr_info("KGDB: Using ttyS%i for session, "
- "please connect your debugger\n", line ? 1 : 0);
- }
-#endif
- return;
-}
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/time.c linux-2.6.24.2/arch/mips/philips/pnx8550/common/time.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/common/time.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/common/time.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,163 +0,0 @@
-/*
- * Copyright 2001, 2002, 2003 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
- *
- * Common time service routines for MIPS machines. See
- * Documents/MIPS/README.txt.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/param.h>
-#include <linux/time.h>
-#include <linux/timer.h>
-#include <linux/smp.h>
-#include <linux/kernel_stat.h>
-#include <linux/spinlock.h>
-#include <linux/interrupt.h>
-
-#include <asm/bootinfo.h>
-#include <asm/cpu.h>
-#include <asm/time.h>
-#include <asm/hardirq.h>
-#include <asm/div64.h>
-#include <asm/debug.h>
-
-#include <int.h>
-#include <cm.h>
-
-static unsigned long cpj;
-
-static cycle_t hpt_read(void)
-{
- return read_c0_count2();
-}
-
-static struct clocksource pnx_clocksource = {
- .name = "pnx8xxx",
- .rating = 200,
- .read = hpt_read,
- .flags = CLOCK_SOURCE_IS_CONTINUOUS,
-};
-
-static void timer_ack(void)
-{
- write_c0_compare(cpj);
-}
-
-static irqreturn_t pnx8xxx_timer_interrupt(int irq, void *dev_id)
-{
- struct clock_event_device *c = dev_id;
-
- /* clear MATCH, signal the event */
- c->event_handler(c);
-
- return IRQ_HANDLED;
-}
-
-static struct irqaction pnx8xxx_timer_irq = {
- .handler = pnx8xxx_timer_interrupt,
- .flags = IRQF_DISABLED | IRQF_PERCPU,
- .name = "pnx8xxx_timer",
-};
-
-static irqreturn_t monotonic_interrupt(int irq, void *dev_id)
-{
- /* Timer 2 clear interrupt */
- write_c0_compare2(-1);
- return IRQ_HANDLED;
-}
-
-static struct irqaction monotonic_irqaction = {
- .handler = monotonic_interrupt,
- .flags = IRQF_DISABLED,
- .name = "Monotonic timer",
-};
-
-static int pnx8xxx_set_next_event(unsigned long delta,
- struct clock_event_device *evt)
-{
- write_c0_compare(delta);
- return 0;
-}
-
-static struct clock_event_device pnx8xxx_clockevent = {
- .name = "pnx8xxx_clockevent",
- .features = CLOCK_EVT_FEAT_ONESHOT,
- .set_next_event = pnx8xxx_set_next_event,
-};
-
-/*
- * plat_time_init() - it does the following things:
- *
- * 1) plat_time_init() -
- * a) (optional) set up RTC routines,
- * b) (optional) calibrate and set the mips_hpt_frequency
- * (only needed if you intended to use cpu counter as timer interrupt
- * source)
- */
-
-__init void plat_time_init(void)
-{
- unsigned int configPR;
- unsigned int n;
- unsigned int m;
- unsigned int p;
- unsigned int pow2p;
-
- clockevents_register_device(&pnx8xxx_clockevent);
- clocksource_register(&pnx_clocksource);
-
- setup_irq(PNX8550_INT_TIMER1, &pnx8xxx_timer_irq);
- setup_irq(PNX8550_INT_TIMER2, &monotonic_irqaction);
-
- /* Timer 1 start */
- configPR = read_c0_config7();
- configPR &= ~0x00000008;
- write_c0_config7(configPR);
-
- /* Timer 2 start */
- configPR = read_c0_config7();
- configPR &= ~0x00000010;
- write_c0_config7(configPR);
-
- /* Timer 3 stop */
- configPR = read_c0_config7();
- configPR |= 0x00000020;
- write_c0_config7(configPR);
-
-
- /* PLL0 sets MIPS clock (PLL1 <=> TM1, PLL6 <=> TM2, PLL5 <=> mem) */
- /* (but only if CLK_MIPS_CTL select value [bits 3:1] is 1: FIXME) */
-
- n = (PNX8550_CM_PLL0_CTL & PNX8550_CM_PLL_N_MASK) >> 16;
- m = (PNX8550_CM_PLL0_CTL & PNX8550_CM_PLL_M_MASK) >> 8;
- p = (PNX8550_CM_PLL0_CTL & PNX8550_CM_PLL_P_MASK) >> 2;
- pow2p = (1 << p);
-
- db_assert(m != 0 && pow2p != 0);
-
- /*
- * Compute the frequency as in the PNX8550 User Manual 1.0, p.186
- * (a.k.a. 8-10). Divide by HZ for a timer offset that results in
- * HZ timer interrupts per second.
- */
- mips_hpt_frequency = 27UL * ((1000000UL * n)/(m * pow2p));
- cpj = (mips_hpt_frequency + HZ / 2) / HZ;
- write_c0_count(0);
- timer_ack();
-
- /* Setup Timer 2 */
- write_c0_count2(0);
- write_c0_compare2(0xffffffff);
-
-}
-
-
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/jbs/board_setup.c linux-2.6.24.2/arch/mips/philips/pnx8550/jbs/board_setup.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/jbs/board_setup.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/jbs/board_setup.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,65 +0,0 @@
-/*
- * JBS Specific board startup routines.
- *
- * Copyright 2005, Embedded Alley Solutions, Inc
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/ioport.h>
-#include <linux/mm.h>
-#include <linux/console.h>
-#include <linux/mc146818rtc.h>
-#include <linux/delay.h>
-
-#include <asm/cpu.h>
-#include <asm/bootinfo.h>
-#include <asm/irq.h>
-#include <asm/mipsregs.h>
-#include <asm/reboot.h>
-#include <asm/pgtable.h>
-
-#include <glb.h>
-
-/* CP0 hazard avoidance. */
-#define BARRIER __asm__ __volatile__(".set noreorder\n\t" \
- "nop; nop; nop; nop; nop; nop;\n\t" \
- ".set reorder\n\t")
-
-void __init board_setup(void)
-{
- unsigned long config0, configpr;
-
- config0 = read_c0_config();
-
- /* clear all three cache coherency fields */
- config0 &= ~(0x7 | (7<<25) | (7<<28));
- config0 |= (CONF_CM_DEFAULT | (CONF_CM_DEFAULT<<25) |
- (CONF_CM_DEFAULT<<28));
- write_c0_config(config0);
- BARRIER;
-
- configpr = read_c0_config7();
- configpr |= (1<<19); /* enable tlb */
- write_c0_config7(configpr);
- BARRIER;
-}
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/jbs/init.c linux-2.6.24.2/arch/mips/philips/pnx8550/jbs/init.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/jbs/init.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/jbs/init.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,56 +0,0 @@
-/*
- *
- * Copyright 2005 Embedded Alley Solutions, Inc
- * source@embeddedalley.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/bootmem.h>
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-#include <linux/string.h>
-#include <linux/kernel.h>
-
-int prom_argc;
-char **prom_argv, **prom_envp;
-extern void __init prom_init_cmdline(void);
-extern char *prom_getenv(char *envname);
-
-const char *get_system_type(void)
-{
- return "Philips PNX8550/JBS";
-}
-
-void __init prom_init(void)
-{
-
- unsigned long memsize;
-
- mips_machtype = MACH_PHILIPS_JBS;
-
- //memsize = 0x02800000; /* Trimedia uses memory above */
- memsize = 0x08000000; /* Trimedia uses memory above */
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/jbs/irqmap.c linux-2.6.24.2/arch/mips/philips/pnx8550/jbs/irqmap.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/jbs/irqmap.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/jbs/irqmap.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,36 +0,0 @@
-/*
- * Philips JBS board irqmap.
- *
- * Copyright 2005 Embedded Alley Solutions, Inc
- * source@embeddealley.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <int.h>
-
-char pnx8550_irq_tab[][5] __initdata = {
- [8] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
- [9] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
- [17] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
-};
-
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/jbs/Makefile linux-2.6.24.2/arch/mips/philips/pnx8550/jbs/Makefile
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/jbs/Makefile 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/jbs/Makefile 1970-01-01 01:00:00.000000000 +0100
@@ -1,4 +0,0 @@
-
-# Makefile for the Philips JBS Board.
-
-lib-y := init.o board_setup.o irqmap.o
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/stb810/board_setup.c linux-2.6.24.2/arch/mips/philips/pnx8550/stb810/board_setup.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/stb810/board_setup.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/stb810/board_setup.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,49 +0,0 @@
-/*
- * STB810 specific board startup routines.
- *
- * Based on the arch/mips/philips/pnx8550/jbs/board_setup.c
- *
- * Author: MontaVista Software, Inc.
- * source@mvista.com
- *
- * Copyright 2005 MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/ioport.h>
-#include <linux/mm.h>
-#include <linux/console.h>
-#include <linux/mc146818rtc.h>
-#include <linux/delay.h>
-
-#include <asm/cpu.h>
-#include <asm/bootinfo.h>
-#include <asm/irq.h>
-#include <asm/mipsregs.h>
-#include <asm/reboot.h>
-#include <asm/pgtable.h>
-
-#include <glb.h>
-
-void __init board_setup(void)
-{
- unsigned long config0, configpr;
-
- config0 = read_c0_config();
-
- /* clear all three cache coherency fields */
- config0 &= ~(0x7 | (7<<25) | (7<<28));
- config0 |= (CONF_CM_DEFAULT | (CONF_CM_DEFAULT<<25) |
- (CONF_CM_DEFAULT<<28));
- write_c0_config(config0);
-
- configpr = read_c0_config7();
- configpr |= (1<<19); /* enable tlb */
- write_c0_config7(configpr);
-}
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/stb810/irqmap.c linux-2.6.24.2/arch/mips/philips/pnx8550/stb810/irqmap.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/stb810/irqmap.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/stb810/irqmap.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,23 +0,0 @@
-/*
- * Philips STB810 board irqmap.
- *
- * Author: MontaVista Software, Inc.
- * source@mvista.com
- *
- * Copyright 2005 MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/init.h>
-#include <int.h>
-
-char pnx8550_irq_tab[][5] __initdata = {
- [8] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
- [9] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
- [10] = { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
-};
-
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/stb810/Makefile linux-2.6.24.2/arch/mips/philips/pnx8550/stb810/Makefile
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/stb810/Makefile 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/stb810/Makefile 1970-01-01 01:00:00.000000000 +0100
@@ -1,4 +0,0 @@
-
-# Makefile for the Philips STB810 Board.
-
-lib-y := prom_init.o board_setup.o irqmap.o
diff -urN linux-2.6.24.2.orig/arch/mips/philips/pnx8550/stb810/prom_init.c linux-2.6.24.2/arch/mips/philips/pnx8550/stb810/prom_init.c
--- linux-2.6.24.2.orig/arch/mips/philips/pnx8550/stb810/prom_init.c 2008-02-26 08:23:00.000000000 +0000
+++ linux-2.6.24.2/arch/mips/philips/pnx8550/stb810/prom_init.c 1970-01-01 01:00:00.000000000 +0100
@@ -1,48 +0,0 @@
-/*
- * STB810 specific prom routines
- *
- * Author: MontaVista Software, Inc.
- * source@mvista.com
- *
- * Copyright 2005 MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/bootmem.h>
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-#include <linux/string.h>
-#include <linux/kernel.h>
-
-int prom_argc;
-char **prom_argv, **prom_envp;
-extern void __init prom_init_cmdline(void);
-extern char *prom_getenv(char *envname);
-
-const char *get_system_type(void)
-{
- return "Philips PNX8550/STB810";
-}
-
-void __init prom_init(void)
-{
- unsigned long memsize;
-
- prom_argc = (int) fw_arg0;
- prom_argv = (char **) fw_arg1;
- prom_envp = (char **) fw_arg2;
-
- prom_init_cmdline();
-
- mips_machtype = MACH_PHILIPS_STB810;
-
- memsize = 0x08000000; /* Trimedia uses memory above */
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff -urN linux-2.6.24.2.orig/drivers/serial/Kconfig linux-2.6.24.2/drivers/serial/Kconfig
--- linux-2.6.24.2.orig/drivers/serial/Kconfig 2008-02-26 08:23:28.000000000 +0000
+++ linux-2.6.24.2/drivers/serial/Kconfig 2008-02-26 08:39:53.000000000 +0000
@@ -925,7 +925,7 @@
depends on MIPS && SOC_PNX8550
select SERIAL_CORE
help
- If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
+ If you have a MIPS-based NXP SoC such as any PNX8XXX device
and you want to use serial ports, say Y. Otherwise, say N.
config SERIAL_PNX8XXX_CONSOLE
@@ -933,7 +933,7 @@
depends on SERIAL_PNX8XXX
select SERIAL_CORE_CONSOLE
help
- If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
+ If you have a MIPS-based NXP SoC such as any PNX8XXX device
and you want to use serial console, say Y. Otherwise, say N.
config SERIAL_CORE
diff -urN linux-2.6.24.2.orig/include/asm-mips/bootinfo.h linux-2.6.24.2/include/asm-mips/bootinfo.h
--- linux-2.6.24.2.orig/include/asm-mips/bootinfo.h 2008-02-26 08:23:45.000000000 +0000
+++ linux-2.6.24.2/include/asm-mips/bootinfo.h 2008-02-26 08:43:04.000000000 +0000
@@ -102,8 +102,12 @@
*/
#define MACH_PHILIPS_NINO 0 /* Nino */
#define MACH_PHILIPS_VELO 1 /* Velo */
-#define MACH_PHILIPS_JBS 2 /* JBS */
-#define MACH_PHILIPS_STB810 3 /* STB810 */
+
+/*
+ * Valid machtype for group NXP
+ */
+#define MACH_NXP_JBS 0 /* JBS */
+#define MACH_NXP_STB810 1 /* STB810 */
/*
* Valid machtype for group SIBYTE
diff -urN linux-2.6.24.2.orig/include/asm-mips/cpu.h linux-2.6.24.2/include/asm-mips/cpu.h
--- linux-2.6.24.2.orig/include/asm-mips/cpu.h 2008-02-26 08:23:45.000000000 +0000
+++ linux-2.6.24.2/include/asm-mips/cpu.h 2008-02-26 08:34:57.000000000 +0000
@@ -29,7 +29,7 @@
#define PRID_COMP_ALCHEMY 0x030000
#define PRID_COMP_SIBYTE 0x040000
#define PRID_COMP_SANDCRAFT 0x050000
-#define PRID_COMP_PHILIPS 0x060000
+#define PRID_COMP_NXP 0x060000
#define PRID_COMP_TOSHIBA 0x070000
#define PRID_COMP_LSI 0x080000
#define PRID_COMP_LEXRA 0x0b0000
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Move arch/mips/philips to arch/mips/nxp
2008-02-27 10:50 Move arch/mips/philips to arch/mips/nxp Daniel Laird
@ 2008-02-28 9:42 ` Ralf Baechle
2008-02-28 16:00 ` M. Warner Losh
0 siblings, 1 reply; 4+ messages in thread
From: Ralf Baechle @ 2008-02-28 9:42 UTC (permalink / raw)
To: Daniel Laird; +Cc: linux-mips
On Wed, Feb 27, 2008 at 10:50:53AM +0000, Daniel Laird wrote:
> This patch moves arch/mips/philips to arch/mips/nxp
> It also modifies a couple of places from Philips -> nxp for more consistancy.
>
> This is in preparation for a new set of chip patches coming soon.
>
> The patch has no other work in in it is primarily a move of current
> code to a new location.
> Have run checkpatch.pl and there are many problems with the patch.
> However none of these are new and are already existing issues in the code base.
> A new patch (to be posted later) will clean up some of these as well.
That's fine. It's actually prefered to post large scale code movments
and functional changes or other cleanups as separate changes. Otherwise
it's hard to spot the functional changes in the amalgated mega-patch.
I didn't apply the patch though because several segments of it reject
when applied to top of the latest tree. The patch headers suggest you
did create the patch against 2.6.24.2. With a diff of 48MB between
2.6.24.2 and head of tree such a patch is bound to fail. Anyway, can
you respin the patch against head?
Other nits - please include a Signed-off-by: header, see
Documentation/SubmittingPatches for what it means. And unless your
mail client does things such as breaking long lines or converting tabs to
spaces please send patches inline.
The usual pointer here: http://www.linux-mips.org/wiki/The_perfect_patch
Ralf
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Move arch/mips/philips to arch/mips/nxp
2008-02-28 9:42 ` Ralf Baechle
@ 2008-02-28 16:00 ` M. Warner Losh
2008-02-28 16:10 ` Ralf Baechle
0 siblings, 1 reply; 4+ messages in thread
From: M. Warner Losh @ 2008-02-28 16:00 UTC (permalink / raw)
To: ralf; +Cc: daniel.j.laird, linux-mips
In message: <20080228094240.GD2750@linux-mips.org>
Ralf Baechle <ralf@linux-mips.org> writes:
: The usual pointer here: http://www.linux-mips.org/wiki/The_perfect_patch
Are the references to BitKeeper still relevant here?
>> Bear in mind that the Subject: of your email becomes a
>> globally-unique identifier for that patch. It propagates all the
>> way into BitKeeper. The Subject: may later be used in developer
------------^^^^^^^^^
>> discussions which refer to the patch. People will want to google
>> for the patch's Subject: to read discussion regarding that patch.
and
>> Do not refer to earlier patches when changelogging a new version of
>> a patch. It's not very useful to have a bitkeeper changelog which
-------------------------------------------^^^^^^^^^
>> says "OK, this fixes the things you mentioned yesterday". Each
>> iteration of the patch should contain a standalone changelog. This
>> implies that you need a patch management system which maintains
>> changelogs. See below.
and
>> Don't bother mentioning what version of the kernel the patch
>> applies to ("applies to 2.6.8-rc1"). This is not interesting
>> information - once the patch is in bitkeeper, of _course_ it
--------------------------------------^^^^^^^^^
>> applied, and it'll probably be merged into a later kernel than the
>> one which you wrote it for.
Warner
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Move arch/mips/philips to arch/mips/nxp
2008-02-28 16:00 ` M. Warner Losh
@ 2008-02-28 16:10 ` Ralf Baechle
0 siblings, 0 replies; 4+ messages in thread
From: Ralf Baechle @ 2008-02-28 16:10 UTC (permalink / raw)
To: M. Warner Losh; +Cc: daniel.j.laird, linux-mips
On Thu, Feb 28, 2008 at 09:00:58AM -0700, M. Warner Losh wrote:
> Are the references to BitKeeper still relevant here?
Vaguely. A while ago bk was in common use in the Linux community. The
licenses for bitkeeper were withdrawn around April 2005 so it's probably
time to remove them.
> >> Bear in mind that the Subject: of your email becomes a
> >> globally-unique identifier for that patch. It propagates all the
> >> way into BitKeeper. The Subject: may later be used in developer
> ------------^^^^^^^^^
> >> discussions which refer to the patch. People will want to google
> >> for the patch's Subject: to read discussion regarding that patch.
>
> and
>
> >> Do not refer to earlier patches when changelogging a new version of
> >> a patch. It's not very useful to have a bitkeeper changelog which
> -------------------------------------------^^^^^^^^^
> >> says "OK, this fixes the things you mentioned yesterday". Each
> >> iteration of the patch should contain a standalone changelog. This
> >> implies that you need a patch management system which maintains
> >> changelogs. See below.
>
> and
>
> >> Don't bother mentioning what version of the kernel the patch
> >> applies to ("applies to 2.6.8-rc1"). This is not interesting
> >> information - once the patch is in bitkeeper, of _course_ it
> --------------------------------------^^^^^^^^^
> >> applied, and it'll probably be merged into a later kernel than the
> >> one which you wrote it for.
Akpm wrote that. I wonder if he's got an updated version of this.
Ralf
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-02-28 16:10 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-02-27 10:50 Move arch/mips/philips to arch/mips/nxp Daniel Laird
2008-02-28 9:42 ` Ralf Baechle
2008-02-28 16:00 ` M. Warner Losh
2008-02-28 16:10 ` Ralf Baechle
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox