* [parisc-linux] [RE:] Installation Prolblem on model 712
@ 2005-03-04 11:21 Μάριος Κ.
2005-03-04 13:37 ` Michael S. Zick
2005-03-04 20:04 ` Michiel Broek
0 siblings, 2 replies; 3+ messages in thread
From: Μάριος Κ. @ 2005-03-04 11:21 UTC (permalink / raw)
To: parisc-linux
[-- Attachment #1.1: Type: text/plain, Size: 2170 bytes --]
This is my dmesg output
The model is 712-60 and not 612
I am begging to suspect the error vomes from the cd-rom
It is a very old cd-rom.
The cd i burned it is good quality and have been written in 4x speed
SCSI subsystem driver Revision: 1.00
53c700: version 2.6 By James...
SCSI0: 53c710 rev 2
SCSI0: LASI SCSI 53c700
SCSI0: (3:0) Synchronous at offest 8, period 100ns
Vendor: Seagete Model:ST34520N Rev:1444
Type:Direct Access ANSI SCSI revision:02
SCSI0: (5:0) Synchronous at offest 8, period 248ns
Vendor: PIONEER Model:CD-ROM DR-104X Rev:0022
Type:Direct CD-ROM ANSI SCSI revision:02
Attached SCSI disk sda at scsi0, channel 0, id 3 lun 0
SCSI device sda: 8888942 512-byte hdwr sectroe (4551 MB)
PARTITION CHECK
sda:unknown partition table
Attached SCSI CD-ROM sr0 at scsi0, channel 0, id 5 lun 0
sr0: scsi-1 drive
Uniform CD-ROM driver Revision:3.12
RAMDISK: Compressed image found at block 0
EXT2-FS warning: Checktime reached, running e2fsck is recommended
UFS:Mounted root (ext2 filesysstem)
NOT FREEING INITMEM (383K)
VFS:DISK CHANGE DETECTED in DRIVE sr(11,0)
SCSI0 (5:0) New error handler wants to abort command
0x28 88 88 88 88 10 00 00 01 00
SCSI0 (5:0) New error handler wants device to reset
0x28 88 88 88 88 10 00 00 01 00
SCSI0 (5:0) New error handler wants bus reset,cmd 13d14c00
0x28 88 88 88 88 10 00 00 01 00
SCSI0(5:0) Synchronous at offset 8,period 248ms
SCSI0 (5:0) New error handler wants to abort command
0x28 88 88 88 88 10 00 00 01 00
SCSI:device set offline-not ready or command retry failed after bus reset
I/O error: dev 0d:00,sector 64
isofs_read_super:dread failed, dev=0d:00, iso_blunum=16,block=16
SCSI0 (3:0) New error handler wants to abort command
0x28 88 88 88 88 10 00 00 08 00
SCSI0 (3:0) New error handler wants device to reset
0x28 88 88 88 88 10 00 00 08 00
SCSI0 (3:0) New error handler wants bus reset,cmd 13d14c00
0x28 88 88 88 88 10 00 00 08 00
SCSI: device setoffline-not ready or command retry failed
after bus reset:host 0 channel 0 id 3 lin 0
---------------------------------
Do You Yahoo!?
Αποκτήστε την δωρεάν σας@yahoo.gr διεύθυνση στο Yahoo! Mail.
[-- Attachment #1.2: Type: text/html, Size: 2597 bytes --]
[-- Attachment #2: Type: text/plain, Size: 169 bytes --]
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [parisc-linux] [RE:] Installation Prolblem on model 712
2005-03-04 11:21 [parisc-linux] [RE:] Installation Prolblem on model 712 Μάριος Κ.
@ 2005-03-04 13:37 ` Michael S. Zick
2005-03-04 20:04 ` Michiel Broek
1 sibling, 0 replies; 3+ messages in thread
From: Michael S. Zick @ 2005-03-04 13:37 UTC (permalink / raw)
To: parisc-linux
On Fri March 4 2005 05:21, =CE=9C=CE=AC=CF=81=CE=B9=CE=BF=CF=82 =CE=9A. wro=
te:
>=20
> This is my dmesg output
>=20
> The model is 712-60 and not 612
>=20
> I am begging to suspect the error vomes from the cd-rom
>=20
Possible, but the installer read the kernel and the=20
initial ram-disk from it.
> It is a very old cd-rom.
>=20
> The cd i burned it is good quality and have been written in 4x speed
>=20
What kernel is this?
These messages look as if they are from a very old kernel.
> =20
>=20
> =20
>=20
> SCSI subsystem driver Revision: 1.00
>=20
> 53c700: version 2.6 By James...
>=20
> SCSI0: 53c710 rev 2
>=20
> SCSI0: LASI SCSI 53c700
>=20
> SCSI0: (3:0) Synchronous at offest 8, period 100ns
>=20
> Vendor: Seagete Model:ST34520N Rev:1444
>=20
> Type:Direct Access ANSI SCSI revision:02
>=20
> SCSI0: (5:0) Synchronous at offest 8, period 248ns
>=20
> Vendor: PIONEER Model:CD-ROM DR-104X Rev:0022
>=20
> Type:Direct CD-ROM ANSI SCSI revision:02
>=20
> =20
>=20
> Attached SCSI disk sda at scsi0, channel 0, id 3 lun 0
>=20
> SCSI device sda: 8888942 512-byte hdwr sectroe (4551 MB)
>=20
> PARTITION CHECK
>=20
> sda:unknown partition table
>
Expected, the install kernel does not know hp-ux disks.
>=20
> Attached SCSI CD-ROM sr0 at scsi0, channel 0, id 5 lun 0
>=20
> sr0: scsi-1 drive
>=20
> Uniform CD-ROM driver Revision:3.12
>=20
> =20
>=20
> RAMDISK: Compressed image found at block 0
>=20
> EXT2-FS warning: Checktime reached, running e2fsck is recommended
>=20
Expected, side effect of how ram disks are built.
> UFS:Mounted root (ext2 filesysstem)
>=20
The following seem to be from an old kernel.
Perhaps someone else on list can give more detail
than myself.
> NOT FREEING INITMEM (383K)
>=20
> VFS:DISK CHANGE DETECTED in DRIVE sr(11,0)
>=20
> SCSI0 (5:0) New error handler wants to abort command
>=20
> 0x28 88 88 88 88 10 00 00 01 00
>=20
> SCSI0 (5:0) New error handler wants device to reset
>=20
> 0x28 88 88 88 88 10 00 00 01 00
>=20
> SCSI0 (5:0) New error handler wants bus reset,cmd 13d14c00
>=20
> 0x28 88 88 88 88 10 00 00 01 00
>=20
> SCSI0(5:0) Synchronous at offset 8,period 248ms
>=20
> SCSI0 (5:0) New error handler wants to abort command
>=20
> 0x28 88 88 88 88 10 00 00 01 00
>=20
> SCSI:device set offline-not ready or command retry failed after bus reset
>=20
> I/O error: dev 0d:00,sector 64
>=20
> isofs_read_super:dread failed, dev=3D0d:00, iso_blunum=3D16,block=3D16
>=20
> SCSI0 (3:0) New error handler wants to abort command
>=20
> 0x28 88 88 88 88 10 00 00 08 00
>=20
> SCSI0 (3:0) New error handler wants device to reset
>=20
> 0x28 88 88 88 88 10 00 00 08 00
>=20
> SCSI0 (3:0) New error handler wants bus reset,cmd 13d14c00
>=20
> 0x28 88 88 88 88 10 00 00 08 00
>=20
> SCSI: device setoffline-not ready or command retry failed
>=20
> after bus reset:host 0 channel 0 id 3 lin 0
>=20
>=20
>=20
>=20
> ---------------------------------
> Do You Yahoo!?
> =EF=BE=81=EF=BF=BD=EF=BF=BD=EF=BF=BD=EF=BF=BD=EF=BE=9E=EF=BF=BD=EF=BF=BD=
=EF=BF=BD =EF=BF=BD=EF=BF=BD=EF=BF=BD =EF=BF=BD=EF=BF=BD=EF=BF=BD=EF=BF=BD=
=EF=BE=9C=EF=BF=BD =EF=BF=BD=EF=BF=BD=EF=BF=BD@yahoo.gr =EF=BF=BD=EF=BF=BD=
=EF=BF=BD=EF=BF=BD=EF=BF=BD=EF=BF=BD=EF=BF=BD=EF=BF=BD=EF=BF=BD =EF=BF=BD=
=EF=BF=BD=EF=BF=BD Yahoo! Mail.
>=20
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [parisc-linux] [RE:] Installation Prolblem on model 712
2005-03-04 11:21 [parisc-linux] [RE:] Installation Prolblem on model 712 Μάριος Κ.
2005-03-04 13:37 ` Michael S. Zick
@ 2005-03-04 20:04 ` Michiel Broek
1 sibling, 0 replies; 3+ messages in thread
From: Michiel Broek @ 2005-03-04 20:04 UTC (permalink / raw)
To: parisc-linux
Op vrijdag 4 maart 2005 12:21, schreef =CE=9C=CE=AC=CF=81=CE=B9=CE=BF=CF=82=
=CE=9A.:
> This is my dmesg output
>
> The model is 712-60 and not 612
>
> I am begging to suspect the error vomes from the cd-rom
>
> It is a very old cd-rom.
>
> The cd i burned it is good quality and have been written in 4x speed
> Attached SCSI CD-ROM sr0 at scsi0, channel 0, id 5 lun 0
>
> sr0: scsi-1 drive
I think your CD drive is too old. I used to have some old single speed HP=20
readers that didn't work with self burned CD's. Youre drive reports scsi-1=
=20
but I think the 712 needs scsi-2 equipment, but I'm not sure about that.
The one I now use reports this:
sr0: scsi3-mmc drive: 0x/0x caddy
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 4, lun 0
I'm using this on a 712/80 with a 2.6.10-pa11 kernel.=20
=2D-=20
Greetings, Michiel Broek
mbroek@mbse.dds.nl or Fidonet 2:280/2802 to Michiel Broek.
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2005-03-04 20:04 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-03-04 11:21 [parisc-linux] [RE:] Installation Prolblem on model 712 Μάριος Κ.
2005-03-04 13:37 ` Michael S. Zick
2005-03-04 20:04 ` Michiel Broek
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox