From: Jim Quinlan <james.quinlan@broadcom.com>
To: linux-pci@vger.kernel.org,
Nicolas Saenz Julienne <nsaenz@kernel.org>,
Bjorn Helgaas <bhelgaas@google.com>,
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>,
Cyril Brulebois <kibi@debian.org>,
Stanimir Varbanov <svarbanov@suse.de>,
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>,
Krzysztof Kozlowski <krzk@kernel.org>,
bcm-kernel-feedback-list@broadcom.com, jim2101024@gmail.com,
james.quinlan@broadcom.com
Cc: "Florian Fainelli" <florian.fainelli@broadcom.com>,
"Lorenzo Pieralisi" <lpieralisi@kernel.org>,
"Krzysztof Wilczyński" <kw@linux.com>,
"Rob Herring" <robh@kernel.org>,
linux-rpi-kernel@lists.infradead.org (moderated list:BROADCOM
BCM2711/BCM2835 ARM ARCHITECTURE),
linux-arm-kernel@lists.infradead.org (moderated list:BROADCOM
BCM2711/BCM2835 ARM ARCHITECTURE),
linux-kernel@vger.kernel.org (open list)
Subject: [PATCH v6 10/13] PCI: brcmstb: Refactor for chips with many regular inbound windows
Date: Thu, 15 Aug 2024 18:57:23 -0400 [thread overview]
Message-ID: <20240815225731.40276-11-james.quinlan@broadcom.com> (raw)
In-Reply-To: <20240815225731.40276-1-james.quinlan@broadcom.com>
Provide support for new chips with multiple inbound windows while
keeping the legacy support for the older chips.
In existing chips there are three inbound windows with fixed purposes: the
first was for mapping SoC internal registers, the second was for memory,
and the third was for memory but with the endian swapped. Typically, only
one window was used.
Complicating the inbound window usage was the fact that the PCIe HW would
do a baroque internal mapping of system memory, and concatenate the regions
of multiple memory controllers.
Newer chips such as the 7712 and Cable Modem SOCs take a step forward and
drop the internal mapping while providing for multiple inbound windows.
This works in concert with the dma-ranges property, where each provided
range becomes an inbound window.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
---
drivers/pci/controller/pcie-brcmstb.c | 235 ++++++++++++++++++++------
1 file changed, 181 insertions(+), 54 deletions(-)
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 2431c5a75cde..c5d3a5e9e0fc 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -75,15 +75,19 @@
#define PCIE_MEM_WIN0_HI(win) \
PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 8)
+/*
+ * NOTE: You may see the term "BAR" in a number of register names used by
+ * this driver. The term is an artifact of when the HW core was an
+ * endpoint device (EP). Now it is a root complex (RC) and anywhere a
+ * register has the term "BAR" it is related to an inbound window.
+ */
+
+#define PCIE_BRCM_MAX_INBOUND_WINS 16
#define PCIE_MISC_RC_BAR1_CONFIG_LO 0x402c
#define PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK 0x1f
-#define PCIE_MISC_RC_BAR2_CONFIG_LO 0x4034
-#define PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_MASK 0x1f
-#define PCIE_MISC_RC_BAR2_CONFIG_HI 0x4038
+#define PCIE_MISC_RC_BAR4_CONFIG_LO 0x40d4
-#define PCIE_MISC_RC_BAR3_CONFIG_LO 0x403c
-#define PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK 0x1f
#define PCIE_MISC_MSI_BAR_CONFIG_LO 0x4044
#define PCIE_MISC_MSI_BAR_CONFIG_HI 0x4048
@@ -130,6 +134,10 @@
(PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK | \
PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK)
+#define PCIE_MISC_UBUS_BAR1_CONFIG_REMAP 0x40ac
+#define PCIE_MISC_UBUS_BAR1_CONFIG_REMAP_ACCESS_EN_MASK BIT(0)
+#define PCIE_MISC_UBUS_BAR4_CONFIG_REMAP 0x410c
+
#define PCIE_MSI_INTR2_BASE 0x4500
/* Offsets from INTR2_CPU and MSI_INTR2 BASE offsets */
@@ -217,12 +225,20 @@ enum pcie_type {
BCM4908,
BCM7278,
BCM2711,
+ BCM7712,
+};
+
+struct inbound_win {
+ u64 size;
+ u64 pci_offset;
+ u64 cpu_addr;
};
struct pcie_cfg_data {
const int *offsets;
const enum pcie_type type;
const bool has_phy;
+ u8 num_inbound_wins;
void (*perst_set)(struct brcm_pcie *pcie, u32 val);
void (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val);
};
@@ -274,6 +290,7 @@ struct brcm_pcie {
struct subdev_regulators *sr;
bool ep_wakeup_capable;
bool has_phy;
+ u8 num_inbound_wins;
};
static inline bool is_bmips(const struct brcm_pcie *pcie)
@@ -396,7 +413,7 @@ static void brcm_pcie_set_gen(struct brcm_pcie *pcie, int gen)
}
static void brcm_pcie_set_outbound_win(struct brcm_pcie *pcie,
- unsigned int win, u64 cpu_addr,
+ u8 win, u64 cpu_addr,
u64 pcie_addr, u64 size)
{
u32 cpu_addr_mb_high, limit_addr_mb_high;
@@ -789,23 +806,62 @@ static void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val)
writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
}
-static int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
- u64 *rc_bar2_size,
- u64 *rc_bar2_offset)
+static void add_inbound_win(struct inbound_win *b, u8 *count, u64 size,
+ u64 cpu_addr, u64 pci_offset)
+{
+ b->size = size;
+ b->cpu_addr = cpu_addr;
+ b->pci_offset = pci_offset;
+ (*count)++;
+}
+
+static int brcm_pcie_get_inbound_wins(struct brcm_pcie *pcie,
+ struct inbound_win inbound_wins[])
{
struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
+ u64 pci_offset, cpu_addr, size = 0, tot_size = 0;
struct resource_entry *entry;
struct device *dev = pcie->dev;
u64 lowest_pcie_addr = ~(u64)0;
int ret, i = 0;
- u64 size = 0;
+ u8 n = 0;
+
+ /*
+ * The HW registers (and PCIe) use order-1 numbering for BARs. As
+ * such, we have inbound_wins[0] unused and BAR1 starts at inbound_wins[1].
+ */
+ struct inbound_win *b_begin = &inbound_wins[1];
+ struct inbound_win *b = b_begin;
+
+ /*
+ * STB chips beside 7712 disable the first inbound window default.
+ * Rather being mapped to system memory it is mapped to the
+ * internal registers of the SoC. This feature is deprecated, has
+ * security considerations, and is not implemented in our modern
+ * SoCs.
+ */
+ if (pcie->type != BCM7712)
+ add_inbound_win(b++, &n, 0, 0, 0);
resource_list_for_each_entry(entry, &bridge->dma_ranges) {
- u64 pcie_beg = entry->res->start - entry->offset;
+ u64 pcie_start = entry->res->start - entry->offset;
+ u64 cpu_start = entry->res->start;
- size += entry->res->end - entry->res->start + 1;
- if (pcie_beg < lowest_pcie_addr)
- lowest_pcie_addr = pcie_beg;
+ size = resource_size(entry->res);
+ tot_size += size;
+ if (pcie_start < lowest_pcie_addr)
+ lowest_pcie_addr = pcie_start;
+ /*
+ * 7712 and newer chips may have many BARs, with each
+ * offering a non-overlapping viewport to system memory.
+ * That being said, each BARs size must still be a power of
+ * two.
+ */
+ if (pcie->type == BCM7712)
+ add_inbound_win(b++, &n, size, cpu_start, pcie_start);
+
+ if (n > pcie->num_inbound_wins)
+ break;
}
if (lowest_pcie_addr == ~(u64)0) {
@@ -813,13 +869,20 @@ static int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
return -EINVAL;
}
+ /*
+ * 7712 and newer chips do not have an internal memory mapping system
+ * that enables multiple memory controllers. As such, it can return
+ * now w/o doing special configuration.
+ */
+ if (pcie->type == BCM7712)
+ return n;
+
ret = of_property_read_variable_u64_array(pcie->np, "brcm,scb-sizes", pcie->memc_size, 1,
PCIE_BRCM_MAX_MEMC);
-
if (ret <= 0) {
/* Make an educated guess */
pcie->num_memc = 1;
- pcie->memc_size[0] = 1ULL << fls64(size - 1);
+ pcie->memc_size[0] = 1ULL << fls64(tot_size - 1);
} else {
pcie->num_memc = ret;
}
@@ -828,10 +891,15 @@ static int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
for (i = 0, size = 0; i < pcie->num_memc; i++)
size += pcie->memc_size[i];
- /* System memory starts at this address in PCIe-space */
- *rc_bar2_offset = lowest_pcie_addr;
- /* The sum of all memc views must also be a power of 2 */
- *rc_bar2_size = 1ULL << fls64(size - 1);
+ /* Our HW mandates that the window size must be a power of 2 */
+ size = 1ULL << fls64(size - 1);
+
+ /*
+ * For STB chips, the BAR2 cpu_addr is hardwired to the start
+ * of system memory, so we set it to 0.
+ */
+ cpu_addr = 0;
+ pci_offset = lowest_pcie_addr;
/*
* We validate the inbound memory view even though we should trust
@@ -866,25 +934,90 @@ static int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
* outbound memory @ 3GB). So instead it will start at the 1x
* multiple of its size
*/
- if (!*rc_bar2_size || (*rc_bar2_offset & (*rc_bar2_size - 1)) ||
- (*rc_bar2_offset < SZ_4G && *rc_bar2_offset > SZ_2G)) {
- dev_err(dev, "Invalid rc_bar2_offset/size: size 0x%llx, off 0x%llx\n",
- *rc_bar2_size, *rc_bar2_offset);
+ if (!size || (pci_offset & (size - 1)) ||
+ (pci_offset < SZ_4G && pci_offset > SZ_2G)) {
+ dev_err(dev, "Invalid inbound_win2_offset/size: size 0x%llx, off 0x%llx\n",
+ size, pci_offset);
return -EINVAL;
}
- return 0;
+ /* Enable inbound window 2, the main inbound window for STB chips */
+ add_inbound_win(b++, &n, size, cpu_addr, pci_offset);
+
+ /*
+ * Disable inbound window 3. On some chips presents the same
+ * window as #2 but the data appears in a settable endianness.
+ */
+ add_inbound_win(b++, &n, 0, 0, 0);
+
+ return n;
+}
+
+static u32 brcm_bar_reg_offset(int bar)
+{
+ if (bar <= 3)
+ return PCIE_MISC_RC_BAR1_CONFIG_LO + 8 * (bar - 1);
+ else
+ return PCIE_MISC_RC_BAR4_CONFIG_LO + 8 * (bar - 4);
+}
+
+static u32 brcm_ubus_reg_offset(int bar)
+{
+ if (bar <= 3)
+ return PCIE_MISC_UBUS_BAR1_CONFIG_REMAP + 8 * (bar - 1);
+ else
+ return PCIE_MISC_UBUS_BAR4_CONFIG_REMAP + 8 * (bar - 4);
+}
+
+static void set_inbound_win_registers(struct brcm_pcie *pcie,
+ const struct inbound_win *inbound_wins,
+ u8 num_inbound_wins)
+{
+ void __iomem *base = pcie->base;
+ int i;
+
+ for (i = 1; i <= num_inbound_wins; i++) {
+ u64 pci_offset = inbound_wins[i].pci_offset;
+ u64 cpu_addr = inbound_wins[i].cpu_addr;
+ u64 size = inbound_wins[i].size;
+ u32 reg_offset = brcm_bar_reg_offset(i);
+ u32 tmp = lower_32_bits(pci_offset);
+
+ u32p_replace_bits(&tmp, brcm_pcie_encode_ibar_size(size),
+ PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK);
+
+ /* Write low */
+ writel_relaxed(tmp, base + reg_offset);
+ /* Write high */
+ writel_relaxed(upper_32_bits(pci_offset), base + reg_offset + 4);
+
+ /*
+ * Most STB chips:
+ * Do nothing.
+ * 7712:
+ * All of their BARs need to be set.
+ */
+ if (pcie->type == BCM7712) {
+ /* BUS remap register settings */
+ reg_offset = brcm_ubus_reg_offset(i);
+ tmp = lower_32_bits(cpu_addr) & ~0xfff;
+ tmp |= PCIE_MISC_UBUS_BAR1_CONFIG_REMAP_ACCESS_EN_MASK;
+ writel_relaxed(tmp, base + reg_offset);
+ tmp = upper_32_bits(cpu_addr);
+ writel_relaxed(tmp, base + reg_offset + 4);
+ }
+ }
}
static int brcm_pcie_setup(struct brcm_pcie *pcie)
{
- u64 rc_bar2_offset, rc_bar2_size;
+ struct inbound_win inbound_wins[PCIE_BRCM_MAX_INBOUND_WINS];
void __iomem *base = pcie->base;
struct pci_host_bridge *bridge;
struct resource_entry *entry;
u32 tmp, burst, aspm_support;
- int num_out_wins = 0;
- int ret, memc;
+ u8 num_out_wins = 0, num_inbound_wins = 0;
+ int memc;
/* Reset the bridge */
pcie->bridge_sw_init_set(pcie, 1);
@@ -933,17 +1066,16 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_PCIE_RCB_64B_MODE_MASK);
writel(tmp, base + PCIE_MISC_MISC_CTRL);
- ret = brcm_pcie_get_rc_bar2_size_and_offset(pcie, &rc_bar2_size,
- &rc_bar2_offset);
- if (ret)
- return ret;
+ num_inbound_wins = brcm_pcie_get_inbound_wins(pcie, inbound_wins);
+ if (num_inbound_wins < 0)
+ return num_inbound_wins;
+
+ set_inbound_win_registers(pcie, inbound_wins, num_inbound_wins);
- tmp = lower_32_bits(rc_bar2_offset);
- u32p_replace_bits(&tmp, brcm_pcie_encode_ibar_size(rc_bar2_size),
- PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_MASK);
- writel(tmp, base + PCIE_MISC_RC_BAR2_CONFIG_LO);
- writel(upper_32_bits(rc_bar2_offset),
- base + PCIE_MISC_RC_BAR2_CONFIG_HI);
+ if (!brcm_pcie_rc_mode(pcie)) {
+ dev_err(pcie->dev, "PCIe RC controller misconfigured as Endpoint\n");
+ return -EINVAL;
+ }
tmp = readl(base + PCIE_MISC_MISC_CTRL);
for (memc = 0; memc < pcie->num_memc; memc++) {
@@ -965,25 +1097,12 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
* 4GB or when the inbound area is smaller than 4GB (taking into
* account the rounding-up we're forced to perform).
*/
- if (rc_bar2_offset >= SZ_4G || (rc_bar2_size + rc_bar2_offset) < SZ_4G)
+ if (inbound_wins[2].pci_offset >= SZ_4G ||
+ (inbound_wins[2].size + inbound_wins[2].pci_offset) < SZ_4G)
pcie->msi_target_addr = BRCM_MSI_TARGET_ADDR_LT_4GB;
else
pcie->msi_target_addr = BRCM_MSI_TARGET_ADDR_GT_4GB;
- if (!brcm_pcie_rc_mode(pcie)) {
- dev_err(pcie->dev, "PCIe RC controller misconfigured as Endpoint\n");
- return -EINVAL;
- }
-
- /* disable the PCIe->GISB memory window (RC_BAR1) */
- tmp = readl(base + PCIE_MISC_RC_BAR1_CONFIG_LO);
- tmp &= ~PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK;
- writel(tmp, base + PCIE_MISC_RC_BAR1_CONFIG_LO);
-
- /* disable the PCIe->SCB memory window (RC_BAR3) */
- tmp = readl(base + PCIE_MISC_RC_BAR3_CONFIG_LO);
- tmp &= ~PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK;
- writel(tmp, base + PCIE_MISC_RC_BAR3_CONFIG_LO);
/* Don't advertise L0s capability if 'aspm-no-l0s' */
aspm_support = PCIE_LINK_STATE_L1;
@@ -1034,7 +1153,7 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
num_out_wins++;
}
- /* PCIe->SCB endian mode for BAR */
+ /* PCIe->SCB endian mode for inbound window */
tmp = readl(base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1);
u32p_replace_bits(&tmp, PCIE_RC_CFG_VENDOR_SPCIFIC_REG1_LITTLE_ENDIAN,
PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK);
@@ -1516,6 +1635,7 @@ static const struct pcie_cfg_data generic_cfg = {
.type = GENERIC,
.perst_set = brcm_pcie_perst_set_generic,
.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
+ .num_inbound_wins = 3,
};
static const struct pcie_cfg_data bcm7425_cfg = {
@@ -1523,6 +1643,7 @@ static const struct pcie_cfg_data bcm7425_cfg = {
.type = BCM7425,
.perst_set = brcm_pcie_perst_set_generic,
.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
+ .num_inbound_wins = 3,
};
static const struct pcie_cfg_data bcm7435_cfg = {
@@ -1530,6 +1651,7 @@ static const struct pcie_cfg_data bcm7435_cfg = {
.type = BCM7435,
.perst_set = brcm_pcie_perst_set_generic,
.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
+ .num_inbound_wins = 3,
};
static const struct pcie_cfg_data bcm4908_cfg = {
@@ -1537,6 +1659,7 @@ static const struct pcie_cfg_data bcm4908_cfg = {
.type = BCM4908,
.perst_set = brcm_pcie_perst_set_4908,
.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
+ .num_inbound_wins = 3,
};
static const int pcie_offset_bcm7278[] = {
@@ -1552,6 +1675,7 @@ static const struct pcie_cfg_data bcm7278_cfg = {
.type = BCM7278,
.perst_set = brcm_pcie_perst_set_7278,
.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_7278,
+ .num_inbound_wins = 3,
};
static const struct pcie_cfg_data bcm2711_cfg = {
@@ -1559,6 +1683,7 @@ static const struct pcie_cfg_data bcm2711_cfg = {
.type = BCM2711,
.perst_set = brcm_pcie_perst_set_generic,
.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
+ .num_inbound_wins = 3,
};
static const struct pcie_cfg_data bcm7216_cfg = {
@@ -1567,6 +1692,7 @@ static const struct pcie_cfg_data bcm7216_cfg = {
.perst_set = brcm_pcie_perst_set_7278,
.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_7278,
.has_phy = true,
+ .num_inbound_wins = 3,
};
static const struct of_device_id brcm_pcie_match[] = {
@@ -1623,6 +1749,7 @@ static int brcm_pcie_probe(struct platform_device *pdev)
pcie->perst_set = data->perst_set;
pcie->bridge_sw_init_set = data->bridge_sw_init_set;
pcie->has_phy = data->has_phy;
+ pcie->num_inbound_wins = data->num_inbound_wins;
pcie->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(pcie->base))
--
2.17.1
next prev parent reply other threads:[~2024-08-15 22:58 UTC|newest]
Thread overview: 60+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-08-15 22:57 [PATCH v6 00/13] PCI: brcnstb: Enable STB 7712 SOC Jim Quinlan
2024-08-15 22:57 ` [PATCH v6 01/13] dt-bindings: PCI: Change brcmstb maintainer and cleanup Jim Quinlan
2024-08-16 6:52 ` Krzysztof Kozlowski
2024-08-16 15:49 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 02/13] dt-bindings: PCI: Use maxItems for reset controllers Jim Quinlan
2024-08-16 6:52 ` Krzysztof Kozlowski
2024-08-16 15:49 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 03/13] dt-bindings: PCI: brcmstb: Add 7712 SoC description Jim Quinlan
2024-08-15 22:57 ` [PATCH v6 04/13] PCI: brcmstb: Use common error handling code in brcm_pcie_probe() Jim Quinlan
2024-08-16 7:02 ` Manivannan Sadhasivam
2024-08-16 15:50 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 05/13] PCI: brcmstb: Use bridge reset if available Jim Quinlan
2024-08-16 7:07 ` Manivannan Sadhasivam
2024-08-16 15:51 ` Florian Fainelli
2024-08-17 17:41 ` Stanimir Varbanov
2024-08-19 18:09 ` Jim Quinlan
2024-08-19 19:39 ` Stanimir Varbanov
2024-08-19 21:49 ` Jim Quinlan
2024-08-20 23:42 ` Stanimir Varbanov
2024-08-21 14:48 ` Jim Quinlan
2024-08-26 10:42 ` Stanimir Varbanov
2024-08-26 14:17 ` Jim Quinlan
2024-08-27 12:27 ` Stanimir Varbanov
2024-08-27 15:01 ` Jim Quinlan
2024-09-01 18:04 ` Krzysztof Wilczyński
2024-08-19 19:07 ` Florian Fainelli
2024-08-20 23:38 ` Stanimir Varbanov
2024-08-21 14:32 ` Jim Quinlan
2024-09-02 19:18 ` Bjorn Helgaas
2024-09-03 14:26 ` Jim Quinlan
2024-09-03 14:46 ` Krzysztof Wilczyński
2024-09-03 17:17 ` Bjorn Helgaas
2024-09-03 17:27 ` Krzysztof Wilczyński
2024-09-10 17:30 ` Jim Quinlan
2024-09-10 17:59 ` Bjorn Helgaas
2024-09-10 19:08 ` Krzysztof Wilczyński
2024-09-12 18:21 ` Jim Quinlan
2024-08-15 22:57 ` [PATCH v6 06/13] PCI: brcmstb: Use swinit " Jim Quinlan
2024-08-16 7:08 ` Manivannan Sadhasivam
2024-08-16 15:51 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 07/13] PCI: brcmstb: PCI: brcmstb: Make HARD_DEBUG, INTR2_CPU_BASE offsets SoC-specific Jim Quinlan
2024-09-02 19:46 ` Bjorn Helgaas
2024-09-03 17:45 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 08/13] PCI: brcmstb: Remove two unused constants from driver Jim Quinlan
2024-08-15 22:57 ` [PATCH v6 09/13] PCI: brcmstb: Don't conflate the reset rescal with phy ctrl Jim Quinlan
2024-08-15 22:57 ` Jim Quinlan [this message]
2024-08-16 7:11 ` [PATCH v6 10/13] PCI: brcmstb: Refactor for chips with many regular inbound windows Manivannan Sadhasivam
2024-08-16 15:57 ` Florian Fainelli
2024-08-17 16:45 ` Stanimir Varbanov
2024-09-02 20:45 ` Bjorn Helgaas
2024-08-15 22:57 ` [PATCH v6 11/13] PCI: brcmstb: Check return value of all reset_control_xxx calls Jim Quinlan
2024-08-16 7:14 ` Manivannan Sadhasivam
2024-08-15 22:57 ` [PATCH v6 12/13] PCI: brcmstb: Change field name from 'type' to 'soc_base' Jim Quinlan
2024-08-16 7:17 ` Manivannan Sadhasivam
2024-08-16 15:51 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 13/13] PCI: brcmstb: Enable 7712 SOCs Jim Quinlan
2024-08-16 7:18 ` [PATCH v6 00/13] PCI: brcnstb: Enable STB 7712 SOC Manivannan Sadhasivam
2024-08-19 17:44 ` Jim Quinlan
2024-08-19 17:48 ` Florian Fainelli
2024-09-01 18:01 ` Krzysztof Wilczyński
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240815225731.40276-11-james.quinlan@broadcom.com \
--to=james.quinlan@broadcom.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=bhelgaas@google.com \
--cc=florian.fainelli@broadcom.com \
--cc=jim2101024@gmail.com \
--cc=kibi@debian.org \
--cc=krzk@kernel.org \
--cc=kw@linux.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=lpieralisi@kernel.org \
--cc=manivannan.sadhasivam@linaro.org \
--cc=nsaenz@kernel.org \
--cc=robh@kernel.org \
--cc=svarbanov@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox