From: Jim Quinlan <james.quinlan@broadcom.com>
To: linux-pci@vger.kernel.org,
Nicolas Saenz Julienne <nsaenz@kernel.org>,
Bjorn Helgaas <bhelgaas@google.com>,
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>,
Cyril Brulebois <kibi@debian.org>,
Stanimir Varbanov <svarbanov@suse.de>,
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>,
Krzysztof Kozlowski <krzk@kernel.org>,
bcm-kernel-feedback-list@broadcom.com, jim2101024@gmail.com,
james.quinlan@broadcom.com
Cc: "Florian Fainelli" <florian.fainelli@broadcom.com>,
"Lorenzo Pieralisi" <lpieralisi@kernel.org>,
"Krzysztof Wilczyński" <kw@linux.com>,
"Rob Herring" <robh@kernel.org>,
"Philipp Zabel" <p.zabel@pengutronix.de>,
linux-rpi-kernel@lists.infradead.org (moderated list:BROADCOM
BCM2711/BCM2835 ARM ARCHITECTURE),
linux-arm-kernel@lists.infradead.org (moderated list:BROADCOM
BCM2711/BCM2835 ARM ARCHITECTURE),
linux-kernel@vger.kernel.org (open list)
Subject: [PATCH v6 11/13] PCI: brcmstb: Check return value of all reset_control_xxx calls
Date: Thu, 15 Aug 2024 18:57:24 -0400 [thread overview]
Message-ID: <20240815225731.40276-12-james.quinlan@broadcom.com> (raw)
In-Reply-To: <20240815225731.40276-1-james.quinlan@broadcom.com>
Always check the return value for invocations of reset_control_xxx() and
propagate the error to the next level. Although the current functions
in reset-brcmstb.c cannot fail, this may someday change.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
---
drivers/pci/controller/pcie-brcmstb.c | 102 ++++++++++++++++++--------
1 file changed, 73 insertions(+), 29 deletions(-)
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index c5d3a5e9e0fc..d19eeeed623b 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -239,8 +239,8 @@ struct pcie_cfg_data {
const enum pcie_type type;
const bool has_phy;
u8 num_inbound_wins;
- void (*perst_set)(struct brcm_pcie *pcie, u32 val);
- void (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val);
+ int (*perst_set)(struct brcm_pcie *pcie, u32 val);
+ int (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val);
};
struct subdev_regulators {
@@ -285,8 +285,8 @@ struct brcm_pcie {
int num_memc;
u64 memc_size[PCIE_BRCM_MAX_MEMC];
u32 hw_rev;
- void (*perst_set)(struct brcm_pcie *pcie, u32 val);
- void (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val);
+ int (*perst_set)(struct brcm_pcie *pcie, u32 val);
+ int (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val);
struct subdev_regulators *sr;
bool ep_wakeup_capable;
bool has_phy;
@@ -749,12 +749,18 @@ static void __iomem *brcm7425_pcie_map_bus(struct pci_bus *bus,
return base + DATA_ADDR(pcie);
}
-static void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val)
+static int brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val)
{
+ int ret = 0;
+
if (val)
- reset_control_assert(pcie->bridge_reset);
+ ret = reset_control_assert(pcie->bridge_reset);
else
- reset_control_deassert(pcie->bridge_reset);
+ ret = reset_control_deassert(pcie->bridge_reset);
+
+ if (ret)
+ dev_err(pcie->dev, "failed to %s 'bridge' reset, err=%d\n",
+ val ? "assert" : "deassert", ret);
if (!pcie->bridge_reset) {
u32 tmp, mask = RGR1_SW_INIT_1_INIT_GENERIC_MASK;
@@ -764,9 +770,11 @@ static void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val
tmp = (tmp & ~mask) | ((val << shift) & mask);
writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
}
+
+ return ret;
}
-static void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val)
+static int brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val)
{
u32 tmp, mask = RGR1_SW_INIT_1_INIT_7278_MASK;
u32 shift = RGR1_SW_INIT_1_INIT_7278_SHIFT;
@@ -774,20 +782,29 @@ static void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val)
tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
tmp = (tmp & ~mask) | ((val << shift) & mask);
writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+
+ return 0;
}
-static void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val)
+static int brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val)
{
+ int ret;
+
if (WARN_ONCE(!pcie->perst_reset, "missing PERST# reset controller\n"))
- return;
+ return -EINVAL;
if (val)
- reset_control_assert(pcie->perst_reset);
+ ret = reset_control_assert(pcie->perst_reset);
else
- reset_control_deassert(pcie->perst_reset);
+ ret = reset_control_deassert(pcie->perst_reset);
+
+ if (ret)
+ dev_err(pcie->dev, "failed to %s 'perst' reset, err=%d\n",
+ val ? "assert" : "deassert", ret);
+ return ret;
}
-static void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val)
+static int brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val)
{
u32 tmp;
@@ -795,15 +812,19 @@ static void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val)
tmp = readl(pcie->base + PCIE_MISC_PCIE_CTRL);
u32p_replace_bits(&tmp, !val, PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK);
writel(tmp, pcie->base + PCIE_MISC_PCIE_CTRL);
+
+ return 0;
}
-static void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val)
+static int brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val)
{
u32 tmp;
tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK);
writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+
+ return 0;
}
static void add_inbound_win(struct inbound_win *b, u8 *count, u64 size,
@@ -1017,19 +1038,28 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
struct resource_entry *entry;
u32 tmp, burst, aspm_support;
u8 num_out_wins = 0, num_inbound_wins = 0;
- int memc;
+ int memc, ret;
/* Reset the bridge */
- pcie->bridge_sw_init_set(pcie, 1);
+ ret = pcie->bridge_sw_init_set(pcie, 1);
+ if (ret)
+ return ret;
/* Ensure that PERST# is asserted; some bootloaders may deassert it. */
- if (pcie->type == BCM2711)
- pcie->perst_set(pcie, 1);
+ if (pcie->type == BCM2711) {
+ ret = pcie->perst_set(pcie, 1);
+ if (ret) {
+ pcie->bridge_sw_init_set(pcie, 0);
+ return ret;
+ }
+ }
usleep_range(100, 200);
/* Take the bridge out of reset */
- pcie->bridge_sw_init_set(pcie, 0);
+ ret = pcie->bridge_sw_init_set(pcie, 0);
+ if (ret)
+ return ret;
tmp = readl(base + HARD_DEBUG(pcie));
if (is_bmips(pcie))
@@ -1248,7 +1278,9 @@ static int brcm_pcie_start_link(struct brcm_pcie *pcie)
int ret, i;
/* Unassert the fundamental reset */
- pcie->perst_set(pcie, 0);
+ ret = pcie->perst_set(pcie, 0);
+ if (ret)
+ return ret;
/*
* Wait for 100ms after PERST# deassertion; see PCIe CEM specification
@@ -1440,15 +1472,17 @@ static inline int brcm_phy_stop(struct brcm_pcie *pcie)
return pcie->has_phy ? brcm_phy_cntl(pcie, 0) : 0;
}
-static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
+static int brcm_pcie_turn_off(struct brcm_pcie *pcie)
{
void __iomem *base = pcie->base;
- int tmp;
+ int tmp, ret;
if (brcm_pcie_link_up(pcie))
brcm_pcie_enter_l23(pcie);
/* Assert fundamental reset */
- pcie->perst_set(pcie, 1);
+ ret = pcie->perst_set(pcie, 1);
+ if (ret)
+ return ret;
/* Deassert request for L23 in case it was asserted */
tmp = readl(base + PCIE_MISC_PCIE_CTRL);
@@ -1461,7 +1495,9 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
writel(tmp, base + HARD_DEBUG(pcie));
/* Shutdown PCIe bridge */
- pcie->bridge_sw_init_set(pcie, 1);
+ ret = pcie->bridge_sw_init_set(pcie, 1);
+
+ return ret;
}
static int pci_dev_may_wakeup(struct pci_dev *dev, void *data)
@@ -1479,9 +1515,12 @@ static int brcm_pcie_suspend_noirq(struct device *dev)
{
struct brcm_pcie *pcie = dev_get_drvdata(dev);
struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
- int ret;
+ int ret, rret;
+
+ ret = brcm_pcie_turn_off(pcie);
+ if (ret)
+ return ret;
- brcm_pcie_turn_off(pcie);
/*
* If brcm_phy_stop() returns an error, just dev_err(). If we
* return the error it will cause the suspend to fail and this is a
@@ -1510,7 +1549,10 @@ static int brcm_pcie_suspend_noirq(struct device *dev)
pcie->sr->supplies);
if (ret) {
dev_err(dev, "Could not turn off regulators\n");
- reset_control_reset(pcie->rescal);
+ rret = reset_control_reset(pcie->rescal);
+ if (rret)
+ dev_err(dev, "failed to reset 'rascal' controller ret=%d\n",
+ rret);
return ret;
}
}
@@ -1525,7 +1567,7 @@ static int brcm_pcie_resume_noirq(struct device *dev)
struct brcm_pcie *pcie = dev_get_drvdata(dev);
void __iomem *base;
u32 tmp;
- int ret;
+ int ret, rret;
base = pcie->base;
ret = clk_prepare_enable(pcie->clk);
@@ -1587,7 +1629,9 @@ static int brcm_pcie_resume_noirq(struct device *dev)
if (pcie->sr)
regulator_bulk_disable(pcie->sr->num_supplies, pcie->sr->supplies);
err_reset:
- reset_control_rearm(pcie->rescal);
+ rret = reset_control_rearm(pcie->rescal);
+ if (rret)
+ dev_err(pcie->dev, "failed to rearm 'rescal' reset, err=%d\n", rret);
err_disable_clk:
clk_disable_unprepare(pcie->clk);
return ret;
--
2.17.1
next prev parent reply other threads:[~2024-08-15 22:58 UTC|newest]
Thread overview: 60+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-08-15 22:57 [PATCH v6 00/13] PCI: brcnstb: Enable STB 7712 SOC Jim Quinlan
2024-08-15 22:57 ` [PATCH v6 01/13] dt-bindings: PCI: Change brcmstb maintainer and cleanup Jim Quinlan
2024-08-16 6:52 ` Krzysztof Kozlowski
2024-08-16 15:49 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 02/13] dt-bindings: PCI: Use maxItems for reset controllers Jim Quinlan
2024-08-16 6:52 ` Krzysztof Kozlowski
2024-08-16 15:49 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 03/13] dt-bindings: PCI: brcmstb: Add 7712 SoC description Jim Quinlan
2024-08-15 22:57 ` [PATCH v6 04/13] PCI: brcmstb: Use common error handling code in brcm_pcie_probe() Jim Quinlan
2024-08-16 7:02 ` Manivannan Sadhasivam
2024-08-16 15:50 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 05/13] PCI: brcmstb: Use bridge reset if available Jim Quinlan
2024-08-16 7:07 ` Manivannan Sadhasivam
2024-08-16 15:51 ` Florian Fainelli
2024-08-17 17:41 ` Stanimir Varbanov
2024-08-19 18:09 ` Jim Quinlan
2024-08-19 19:39 ` Stanimir Varbanov
2024-08-19 21:49 ` Jim Quinlan
2024-08-20 23:42 ` Stanimir Varbanov
2024-08-21 14:48 ` Jim Quinlan
2024-08-26 10:42 ` Stanimir Varbanov
2024-08-26 14:17 ` Jim Quinlan
2024-08-27 12:27 ` Stanimir Varbanov
2024-08-27 15:01 ` Jim Quinlan
2024-09-01 18:04 ` Krzysztof Wilczyński
2024-08-19 19:07 ` Florian Fainelli
2024-08-20 23:38 ` Stanimir Varbanov
2024-08-21 14:32 ` Jim Quinlan
2024-09-02 19:18 ` Bjorn Helgaas
2024-09-03 14:26 ` Jim Quinlan
2024-09-03 14:46 ` Krzysztof Wilczyński
2024-09-03 17:17 ` Bjorn Helgaas
2024-09-03 17:27 ` Krzysztof Wilczyński
2024-09-10 17:30 ` Jim Quinlan
2024-09-10 17:59 ` Bjorn Helgaas
2024-09-10 19:08 ` Krzysztof Wilczyński
2024-09-12 18:21 ` Jim Quinlan
2024-08-15 22:57 ` [PATCH v6 06/13] PCI: brcmstb: Use swinit " Jim Quinlan
2024-08-16 7:08 ` Manivannan Sadhasivam
2024-08-16 15:51 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 07/13] PCI: brcmstb: PCI: brcmstb: Make HARD_DEBUG, INTR2_CPU_BASE offsets SoC-specific Jim Quinlan
2024-09-02 19:46 ` Bjorn Helgaas
2024-09-03 17:45 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 08/13] PCI: brcmstb: Remove two unused constants from driver Jim Quinlan
2024-08-15 22:57 ` [PATCH v6 09/13] PCI: brcmstb: Don't conflate the reset rescal with phy ctrl Jim Quinlan
2024-08-15 22:57 ` [PATCH v6 10/13] PCI: brcmstb: Refactor for chips with many regular inbound windows Jim Quinlan
2024-08-16 7:11 ` Manivannan Sadhasivam
2024-08-16 15:57 ` Florian Fainelli
2024-08-17 16:45 ` Stanimir Varbanov
2024-09-02 20:45 ` Bjorn Helgaas
2024-08-15 22:57 ` Jim Quinlan [this message]
2024-08-16 7:14 ` [PATCH v6 11/13] PCI: brcmstb: Check return value of all reset_control_xxx calls Manivannan Sadhasivam
2024-08-15 22:57 ` [PATCH v6 12/13] PCI: brcmstb: Change field name from 'type' to 'soc_base' Jim Quinlan
2024-08-16 7:17 ` Manivannan Sadhasivam
2024-08-16 15:51 ` Florian Fainelli
2024-08-15 22:57 ` [PATCH v6 13/13] PCI: brcmstb: Enable 7712 SOCs Jim Quinlan
2024-08-16 7:18 ` [PATCH v6 00/13] PCI: brcnstb: Enable STB 7712 SOC Manivannan Sadhasivam
2024-08-19 17:44 ` Jim Quinlan
2024-08-19 17:48 ` Florian Fainelli
2024-09-01 18:01 ` Krzysztof Wilczyński
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240815225731.40276-12-james.quinlan@broadcom.com \
--to=james.quinlan@broadcom.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=bhelgaas@google.com \
--cc=florian.fainelli@broadcom.com \
--cc=jim2101024@gmail.com \
--cc=kibi@debian.org \
--cc=krzk@kernel.org \
--cc=kw@linux.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=lpieralisi@kernel.org \
--cc=manivannan.sadhasivam@linaro.org \
--cc=nsaenz@kernel.org \
--cc=p.zabel@pengutronix.de \
--cc=robh@kernel.org \
--cc=svarbanov@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox