[PATCH v2 0/5] phy: qcom-mipi-csi2: Add D-PHY support for sa8775p, qcs8300 and sc7280

[PATCH v2 0/5] phy: qcom-mipi-csi2: Add D-PHY support for sa8775p, qcs8300 and sc7280

[Anusha Arun Nandi]

This series extends the generic Qualcomm MIPI CSI2 PHY driver
(drivers/phy/qualcomm/phy-qcom-mipi-csi2-*) with three additional
CSIPHY variants: SA8775P, QCS8300 and SC7280. The driver currently
only supports x1e80100; these SoCs let CAMSS consume the CSIPHY through
the common PHY framework instead of the CSIPHY logic embedded in the
legacy in-tree CAMSS driver.

QCS8300 shares the same CSIPHY D-PHY hardware as SA8775P, so it does
not need its own of_device_id entry: the qcom,csi2-phy.yaml binding
declares "qcom,sa8775p-csi2-phy" as QCS8300's fallback compatible, and
QCS8300 CSIPHY nodes bind through patch 4's existing
"qcom,sa8775p-csi2-phy" match entry.

Tested on sa8775p, qcs8300 and sc7280.

Anusha Arun Nandi (5):
  dt-bindings: phy: qcom: Add common qcom,csi2-phy
  phy: qcom-mipi-csi2: Make timer and OPP clock names configurable
  phy: qcom-mipi-csi2: Make OPP table optional
  phy: qcom-mipi-csi2: Add sa8775p D-PHY support
  phy: qcom-mipi-csi2: Add sc7280 D-PHY provider

 .../bindings/phy/qcom,csi2-phy.yaml           | 176 +++++++++++++
 .../qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c    | 233 +++++++++++++++++-
 .../phy/qualcomm/phy-qcom-mipi-csi2-core.c    |  76 +++---
 drivers/phy/qualcomm/phy-qcom-mipi-csi2.h     |   5 +
 4 files changed, 455 insertions(+), 35 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,csi2-phy.yaml
--
Best regards,
-- 
Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 1/5] dt-bindings: phy: qcom: Add common qcom,csi2-phy

[Anusha Arun Nandi]

SA8775P, QCS8300 and SC7280 CSI2 PHYs are bit-for-bit identical in
devicetree shape (ports, bus-type, data-lanes, operating-points-v2,
clocks, single "top" power-domain, vdda-phy/vdda-pll supplies).

Describe all three with a single qcom,csi2-phy.yaml and a compatible
oneOf, rather than one standalone schema per SoC. QCS8300 is further
required to be paired with a qcom,sa8775p-csi2-phy fallback
compatible, the same way other Qualcomm bindings express full
hardware compatibility between two SoCs (see qcom,qusb2-phy.yaml);
this lets the driver bind QCS8300 nodes via its qcom,sa8775p-csi2-phy
match entry rather than carrying a duplicate one.

qcom,x1e80100-csi2-phy.yaml is a separate PHY with a different shape
(3 clocks, 3 power-domains, different supply names, DPHY split-mode
support) and is left untouched.

Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>
Signed-off-by: Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
---
 .../bindings/phy/qcom,csi2-phy.yaml           | 176 ++++++++++++++++++
 1 file changed, 176 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,csi2-phy.yaml

diff --git a/Documentation/devicetree/bindings/phy/qcom,csi2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,csi2-phy.yaml
new file mode 100644
index 000000000000..5d25547528bd
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,csi2-phy.yaml
@@ -0,0 +1,176 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (c) 2026 Qualcomm Innovation Center, Inc. All rights reserved.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/qcom,csi2-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm CSI2 PHY
+
+maintainers:
+  - Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
+
+description:
+  Qualcomm MIPI CSI2 D-PHY. Connects MIPI CSI2 sensors to Qualcomm's Camera
+  CSI Decoder.
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+          - qcom,sa8775p-csi2-phy
+          - qcom,sc7280-csi2-phy
+      - items:
+          - enum:
+              - qcom,qcs8300-csi2-phy
+          - const: qcom,sa8775p-csi2-phy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: core
+      - const: timer
+
+  interrupts:
+    maxItems: 1
+
+  operating-points-v2: true
+
+  opp-table:
+    type: object
+
+  power-domains:
+    items:
+      - description: Titan Top GDSC - Titan ISP Block, Global Distributed Switch Controller.
+
+  power-domain-names:
+    items:
+      - const: top
+
+  vdda-phy-supply:
+    description: Phandle to PHY supply.
+
+  vdda-pll-supply:
+    description: Phandle to PLL supply.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        description:
+          Sensor input. A single sensor is described by a single endpoint
+          with one to four data lanes, numbered 1-4. The clock lane is
+          position 0.
+
+        unevaluatedProperties: false
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+            properties:
+              bus-type:
+                enum:
+                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+                default: 4
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+                items:
+                  minimum: 1
+                  maximum: 4
+                description:
+                  Data lane positions following this endpoint's clock
+                  lane. Positions are a per-port logical numbering, not
+                  package pad or ball positions.
+
+            required:
+              - data-lanes
+              - remote-endpoint
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Output to the CAMSS CSID controller.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - interrupts
+  - operating-points-v2
+  - power-domains
+  - power-domain-names
+  - vdda-phy-supply
+  - vdda-pll-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,sa8775p-camcc.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/media/video-interfaces.h>
+
+    phy@ac9c000 {
+        compatible = "qcom,sa8775p-csi2-phy";
+        reg = <0x0ac9c000 0x2000>;
+
+        clocks = <&camcc CAM_CC_CSIPHY0_CLK>,
+                 <&camcc CAM_CC_CSI0PHYTIMER_CLK>;
+        clock-names = "core",
+                      "timer";
+
+        interrupts = <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>;
+
+        operating-points-v2 = <&csiphy_opp_table>;
+
+        power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+        power-domain-names = "top";
+
+        vdda-phy-supply = <&vreg_l4a>;
+        vdda-pll-supply = <&vreg_l1c>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                csiphy0_in: endpoint {
+                    bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+                    data-lanes = <1 2 3 4>;
+                    remote-endpoint = <&sensor_out>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                csiphy0_out: endpoint {
+                    remote-endpoint = <&csid_in>;
+                };
+            };
+        };
+
+        csiphy_opp_table: opp-table {
+            compatible = "operating-points-v2";
+
+            opp-300000000 {
+                opp-hz = /bits/ 64 <300000000>;
+            };
+        };
+    };
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 2/5] phy: qcom-mipi-csi2: Make timer and OPP clock names configurable

[Anusha Arun Nandi]

The timer-clock lookup in phy_qcom_mipi_csi2_probe() and the OPP
clkname passed to devm_pm_opp_set_clkname() were both hardcoded
string literals sized to x1e80100 ("timer"/"core"). Add
timer_clk_name/opp_clk_name to struct mipi_csi2phy_soc_cfg so each
SoC can declare its own clock-name strings instead.

x1e80100's soc_cfg now declares "timer"/"core" explicitly; no
behaviour change.

Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>
Signed-off-by: Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c | 2 ++
 drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c     | 4 ++--
 drivers/phy/qualcomm/phy-qcom-mipi-csi2.h          | 3 +++
 3 files changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
index 966d79c98f9b..8f1939e81e13 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
@@ -380,6 +380,8 @@ const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_4nm_x1e = {
 	.num_supplies = ARRAY_SIZE(x1e_supplies),
 	.clk_names = (const char **)x1e_clks,
 	.num_clk = ARRAY_SIZE(x1e_clks),
+	.timer_clk_name = "timer",
+	.opp_clk_name = "core",
 	.genpds = x1e_genpds,
 	.num_genpds = ARRAY_SIZE(x1e_genpds),
 };
diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
index 269232499fca..3de25728ed28 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
@@ -397,7 +397,7 @@ static int phy_qcom_mipi_csi2_probe(struct platform_device *pdev)
 		if (!csi2phy->clks[i].id)
 			return dev_err_probe(dev, -EINVAL, "Missing clock-names\n");
 
-		if (!strcmp(csi2phy->clks[i].id, "timer")) {
+		if (!strcmp(csi2phy->clks[i].id, csi2phy->soc_cfg->timer_clk_name)) {
 			csi2phy->timer_clk = csi2phy->clks[i].clk;
 			break;
 		}
@@ -405,7 +405,7 @@ static int phy_qcom_mipi_csi2_probe(struct platform_device *pdev)
 	if (!csi2phy->timer_clk)
 		return dev_err_probe(dev, -ENODEV, "no timer clock\n");
 
-	ret = devm_pm_opp_set_clkname(dev, "core");
+	ret = devm_pm_opp_set_clkname(dev, csi2phy->soc_cfg->opp_clk_name);
 	if (ret)
 		return dev_err_probe(dev, ret, "Failed to set opp clkname\n");
 
diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
index 7e55ae007370..359b58660db8 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
@@ -68,6 +68,9 @@ struct mipi_csi2phy_soc_cfg {
 	const char ** const clk_names;
 	const unsigned int num_clk;
 
+	const char * const timer_clk_name;
+	const char * const opp_clk_name;
+
 	const struct mipi_csi2_genpd *genpds;
 	const unsigned int num_genpds;
 };
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 3/5] phy: qcom-mipi-csi2: Make OPP table optional

[Anusha Arun Nandi]

Not every SoC the generic MIPI CSI2 PHY driver supports needs an OPP
table: a CSIPHY with only a single, unscaled power-domain has no
performance state to vote on, so running its "core" clock through
the OPP framework buys nothing over a plain clk_set_rate(). Skip
devm_pm_opp_set_clkname()/devm_pm_opp_of_add_table() in probe() and
the OPP/performance-state handling in
phy_qcom_mipi_csi2_set_clock_rates() when soc_cfg->opp_clk_name is
unset, falling back to clk_round_rate()/clk_set_rate() on the timer
clock only.

x1e80100 still sets opp_clk_name, so this is a no-op for it.

Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>
Signed-off-by: Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
---
 .../phy/qualcomm/phy-qcom-mipi-csi2-core.c    | 72 ++++++++++---------
 1 file changed, 39 insertions(+), 33 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
index 3de25728ed28..181813caf282 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
@@ -32,40 +32,43 @@ phy_qcom_mipi_csi2_set_clock_rates(struct mipi_csi2phy_device *csi2phy,
 	unsigned long opp_rate = link_freq / 4;
 	struct dev_pm_opp *opp;
 	long timer_rate;
-	int i, pstate;
+	int i = 0, pstate;
 	int ret;
 
-	opp = dev_pm_opp_find_freq_ceil(dev, &opp_rate);
-	if (IS_ERR(opp)) {
-		dev_err(csi2phy->dev, "Couldn't find ceiling for %lld Hz\n",
-			link_freq);
-		return PTR_ERR(opp);
-	}
+	if (csi2phy->soc_cfg->opp_clk_name) {
+		opp = dev_pm_opp_find_freq_ceil(dev, &opp_rate);
+		if (IS_ERR(opp)) {
+			dev_err(csi2phy->dev, "Couldn't find ceiling for %lld Hz\n",
+				link_freq);
+			return PTR_ERR(opp);
+		}
 
-	pstate = 0;
-	for (i = 0; csi2phy->pd_list && i < csi2phy->pd_list->num_pds; i++) {
-		unsigned int perf;
+		pstate = 0;
+		for (i = 0; csi2phy->pd_list && i < csi2phy->pd_list->num_pds; i++) {
+			unsigned int perf;
 
-		if (!csi2phy->soc_cfg->genpds[i].scaled)
-			continue;
+			if (!csi2phy->soc_cfg->genpds[i].scaled)
+				continue;
 
-		perf = dev_pm_opp_get_required_pstate(opp, pstate);
-		pstate += 1;
+			perf = dev_pm_opp_get_required_pstate(opp, pstate);
+			pstate += 1;
 
-		ret = dev_pm_genpd_set_performance_state(csi2phy->pd_list->pd_devs[i], perf);
-		if (ret) {
-			dev_err(csi2phy->dev, "Couldn't set perf state %u\n",
-				perf);
-			dev_pm_opp_put(opp);
-			goto unset_pstate;
+			ret = dev_pm_genpd_set_performance_state(csi2phy->pd_list->pd_devs[i],
+								 perf);
+			if (ret) {
+				dev_err(csi2phy->dev, "Couldn't set perf state %u\n",
+					perf);
+				dev_pm_opp_put(opp);
+				goto unset_pstate;
+			}
 		}
-	}
-	dev_pm_opp_put(opp);
+		dev_pm_opp_put(opp);
 
-	ret = dev_pm_opp_set_rate(dev, opp_rate);
-	if (ret) {
-		dev_err(csi2phy->dev, "dev_pm_opp_set_rate() fail\n");
-		goto unset_opp_rate;
+		ret = dev_pm_opp_set_rate(dev, opp_rate);
+		if (ret) {
+			dev_err(csi2phy->dev, "dev_pm_opp_set_rate() fail\n");
+			goto unset_opp_rate;
+		}
 	}
 
 	timer_rate = clk_round_rate(csi2phy->timer_clk, link_freq / 4);
@@ -83,7 +86,8 @@ phy_qcom_mipi_csi2_set_clock_rates(struct mipi_csi2phy_device *csi2phy,
 	return 0;
 
 unset_opp_rate:
-	dev_pm_opp_set_rate(dev, 0);
+	if (csi2phy->soc_cfg->opp_clk_name)
+		dev_pm_opp_set_rate(dev, 0);
 
 unset_pstate:
 	while (i--) {
@@ -405,13 +409,15 @@ static int phy_qcom_mipi_csi2_probe(struct platform_device *pdev)
 	if (!csi2phy->timer_clk)
 		return dev_err_probe(dev, -ENODEV, "no timer clock\n");
 
-	ret = devm_pm_opp_set_clkname(dev, csi2phy->soc_cfg->opp_clk_name);
-	if (ret)
-		return dev_err_probe(dev, ret, "Failed to set opp clkname\n");
+	if (csi2phy->soc_cfg->opp_clk_name) {
+		ret = devm_pm_opp_set_clkname(dev, csi2phy->soc_cfg->opp_clk_name);
+		if (ret)
+			return dev_err_probe(dev, ret, "Failed to set opp clkname\n");
 
-	ret = devm_pm_opp_of_add_table(dev);
-	if (ret)
-		return dev_err_probe(dev, ret, "invalid OPP table in device tree\n");
+		ret = devm_pm_opp_of_add_table(dev);
+		if (ret)
+			return dev_err_probe(dev, ret, "invalid OPP table in device tree\n");
+	}
 
 	num_supplies = csi2phy->soc_cfg->num_supplies;
 	csi2phy->supplies = devm_kzalloc(dev, sizeof(*csi2phy->supplies) * num_supplies,
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 4/5] phy: qcom-mipi-csi2: Add sa8775p D-PHY support

[Anusha Arun Nandi]

Add the SA8775P CSIPHY to the generic MIPI CSI2 PHY driver, 
bound to a new "qcom,sa8775p-csi2-phy" compatible
and reusing the existing D-PHY 2-phase hw ops
(phy_qcom_mipi_csi2_ops_3ph_1_0). The lane_regs_sa8775p[] init
sequence is the CSIPHY v1.3.0 2-phase 2.5Gbps 4-lane D-PHY register
set ported verbatim from the legacy in-tree camss-csiphy-3ph-1-0.c
table; common_regs_offset is 0x800.

SA8775P reuses the same "timer"/"core" clock names as x1e80100
(timer_clk_name/opp_clk_name added by a preceding patch). Like
x1e80100, its CSIPHY core clock is OPP-scaled against the sensor's
link frequency via the shared csiphy_opp_table in lemans.dtsi,
matching the legacy in-tree CSIPHY driver's own sa8775p_resources
OPP wiring.

SA8775P's CSIPHY has a single power-domain, the Titan Top GDSC,
matching the legacy in-tree CAMSS driver's sa8775p_resources.pd_name
= "top" and the existing lemans.dtsi camss node. Like x1e80100's own
"top" domain, it is not OPP-scaled, only kept enabled.

QCS8300 shares this same CSIPHY D-PHY hardware and does not need its
own of_device_id entry: the qcom,csi2-phy.yaml binding declares
"qcom,sa8775p-csi2-phy" as QCS8300's fallback compatible, so QCS8300
CSIPHY nodes bind through the "qcom,sa8775p-csi2-phy" match entry
added here.

Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>
Signed-off-by: Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
---
 .../qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c    | 110 +++++++++++++++++-
 .../phy/qualcomm/phy-qcom-mipi-csi2-core.c    |   1 +
 drivers/phy/qualcomm/phy-qcom-mipi-csi2.h     |   1 +
 3 files changed, 111 insertions(+), 1 deletion(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
index 8f1939e81e13..3e93e0b49106 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
@@ -317,7 +317,6 @@ static int phy_qcom_mipi_csi2_lanes_enable(struct mipi_csi2phy_device *csi2phy,
 	writel(val, csi2phy->base +
 	       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->common_regs_offset, 7));
 
-	val = 0x00;
 	writel(val, csi2phy->base +
 	       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->common_regs_offset, 0));
 
@@ -385,3 +384,112 @@ const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_4nm_x1e = {
 	.genpds = x1e_genpds,
 	.num_genpds = ARRAY_SIZE(x1e_genpds),
 };
+
+/* 5nm 2PH v1.3.0 2p5Gbps 4 lane DPHY mode */
+static const struct mipi_csi2phy_lane_regs lane_regs_sa8775p[] = {
+	{.reg_addr = 0x0724, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0728, .reg_data = 0x04, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0700, .reg_data = 0x80, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x070c, .reg_data = 0xff, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0738, .reg_data = 0x1f, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x072c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0734, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0710, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x071c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0714, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x073c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0704, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0720, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0708, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x0024, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0000, .reg_data = 0x8d, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0038, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x002c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0034, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0010, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x001c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0014, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x003c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0004, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0020, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0008, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x0224, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0200, .reg_data = 0x8d, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0238, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x022c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0234, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0210, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x021c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0214, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x023c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0204, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0220, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0208, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x0424, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0400, .reg_data = 0x8d, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0438, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x042c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0434, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0410, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x041c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0414, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x043c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0404, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0420, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0408, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x0624, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0600, .reg_data = 0x8d, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0638, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x062c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0634, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0610, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x061c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0614, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x063c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0604, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0620, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0608, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x005c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x0060, .reg_data = 0xfd, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x0064, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x025c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x0260, .reg_data = 0xfd, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x0264, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x045c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x0460, .reg_data = 0xfd, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x0464, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x065c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x0660, .reg_data = 0xfd, .param_type = CSIPHY_SKEW_CAL},
+	{.reg_addr = 0x0664, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL},
+};
+
+static const char * const sa8775p_clks[] = {
+	"core",
+	"timer",
+};
+
+static const char * const sa8775p_supplies[] = {
+	"vdda-phy",
+	"vdda-pll",
+};
+
+static const struct mipi_csi2_genpd sa8775p_genpds[] = {
+	{ .name = "top", .scaled = false },
+};
+
+const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_sa8775p = {
+	.ops = &phy_qcom_mipi_csi2_ops_3ph_1_0,
+	.reg_info = {
+		.init_seq = lane_regs_sa8775p,
+		.lane_array_size = ARRAY_SIZE(lane_regs_sa8775p),
+		.common_regs_offset = 0x800,
+	},
+	.supply_names = (const char **)sa8775p_supplies,
+	.num_supplies = ARRAY_SIZE(sa8775p_supplies),
+	.clk_names = (const char **)sa8775p_clks,
+	.num_clk = ARRAY_SIZE(sa8775p_clks),
+	.timer_clk_name = "timer",
+	.opp_clk_name = "core",
+	.genpds = sa8775p_genpds,
+	.num_genpds = ARRAY_SIZE(sa8775p_genpds),
+};
diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
index 181813caf282..244e851ff24d 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
@@ -454,6 +454,7 @@ static int phy_qcom_mipi_csi2_probe(struct platform_device *pdev)
 }
 
 static const struct of_device_id phy_qcom_mipi_csi2_of_match_table[] = {
+	{ .compatible	= "qcom,sa8775p-csi2-phy", .data = &mipi_csi2_dphy_sa8775p },
 	{ .compatible	= "qcom,x1e80100-csi2-phy", .data = &mipi_csi2_dphy_4nm_x1e },
 	{ }
 };
diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
index 359b58660db8..5578741c0930 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
@@ -96,5 +96,6 @@ struct mipi_csi2phy_device {
 };
 
 extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_4nm_x1e;
+extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_sa8775p;
 
 #endif /* __PHY_QCOM_MIPI_CSI2_H__ */
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 5/5] phy: qcom-mipi-csi2: Add sc7280 D-PHY provider

[Anusha Arun Nandi]

Add the SC7280 CSIPHY to the generic MIPI CSI2 PHY driver, 
bound to a new "qcom,sc7280-csi2-phy" compatible
and reusing the existing D-PHY 2-phase hw ops
(phy_qcom_mipi_csi2_ops_3ph_1_0). The lane_regs_sc7280[] init
sequence is the CSIPHY 5nm 2-phase 2.5Gbps 4-lane D-PHY register
set ported from the legacy in-tree camss-csiphy-3ph-1-0.c table,
with the entries that table left as do-not-program placeholders
simply omitted here rather than carried as a new marker. The
soc_cfg declares the core/timer clocks (matching x1e80100's and
sa8775p's clock-names convention for this pair) and the
vdda-phy/vdda-pll supplies.

Like x1e80100 and SA8775P, SC7280's CSIPHY core clock is OPP-scaled
against the sensor's link frequency via the shared csiphy_opp_table
in kodiak.dtsi, so opp_clk_name is set to "core" here too. SC7280's
CSIPHY has a single power-domain, the Titan Top GDSC, matching
camss.c's sc7280_resources.pd_name = "top" and kodiak.dtsi's
existing camss node; it is not OPP-scaled, only kept enabled.

Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>
Signed-off-by: Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
---
 .../qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c    | 122 ++++++++++++++++++
 .../phy/qualcomm/phy-qcom-mipi-csi2-core.c    |   1 +
 drivers/phy/qualcomm/phy-qcom-mipi-csi2.h     |   1 +
 3 files changed, 124 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
index 3e93e0b49106..dc31c5cd1475 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
@@ -493,3 +493,125 @@ const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_sa8775p = {
 	.genpds = sa8775p_genpds,
 	.num_genpds = ARRAY_SIZE(sa8775p_genpds),
 };
+
+/* sc7280 5nm 2PH 2p5Gbps 4 lane DPHY mode */
+static const struct mipi_csi2phy_lane_regs lane_regs_sc7280[] = {
+	{.reg_addr = 0x0030, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0900, .reg_data = 0x05, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0908, .reg_data = 0x10, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0904, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0904, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0004, .reg_data = 0x0C, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x002C, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0034, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0010, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x001C, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x003C, .reg_data = 0xB8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0008, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x0000, .reg_data = 0x8D, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0038, .reg_data = 0xFE, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0014, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0800, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0884, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0730, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0C80, .reg_data = 0x05, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0C88, .reg_data = 0x10, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0C84, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0C84, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0704, .reg_data = 0x0C, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x072C, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0734, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0710, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x071C, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x073C, .reg_data = 0xB8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0708, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x0700, .reg_data = 0x80, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x070c, .reg_data = 0xA5, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0738, .reg_data = 0x1F, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0714, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0728, .reg_data = 0x04, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0800, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0884, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0230, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0A00, .reg_data = 0x05, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0A08, .reg_data = 0x10, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0A04, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0A04, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0204, .reg_data = 0x0C, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x022C, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0234, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0210, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x021C, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x023C, .reg_data = 0xB8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0208, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x0200, .reg_data = 0x8D, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0238, .reg_data = 0xFE, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0214, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0800, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0884, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0430, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0B00, .reg_data = 0x05, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0B08, .reg_data = 0x10, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0B04, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0B04, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0404, .reg_data = 0x0C, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x042C, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0434, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0410, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x041C, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x043C, .reg_data = 0xB8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0408, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x0400, .reg_data = 0x8D, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0438, .reg_data = 0xFE, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0414, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0800, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0884, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0630, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0C00, .reg_data = 0x05, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0C08, .reg_data = 0x10, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0C04, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0C04, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0604, .reg_data = 0x0C, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x062C, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0634, .reg_data = 0x07, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0610, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x061C, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x063C, .reg_data = 0xB8, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0608, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{.reg_addr = 0x0600, .reg_data = 0x8D, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0638, .reg_data = 0xFE, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0614, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0800, .reg_data = 0x02, .param_type = CSIPHY_DEFAULT_PARAMS},
+	{.reg_addr = 0x0884, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS},
+};
+
+static const char * const sc7280_clks[] = {
+	"core",
+	"timer",
+};
+
+static const char * const sc7280_supplies[] = {
+	"vdda-phy",
+	"vdda-pll",
+};
+
+static const struct mipi_csi2_genpd sc7280_genpds[] = {
+	{ .name = "top", .scaled = false },
+};
+
+const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_sc7280 = {
+	.ops = &phy_qcom_mipi_csi2_ops_3ph_1_0,
+	.reg_info = {
+		.init_seq = lane_regs_sc7280,
+		.lane_array_size = ARRAY_SIZE(lane_regs_sc7280),
+		.common_regs_offset = 0x800,
+	},
+	.supply_names = (const char **)sc7280_supplies,
+	.num_supplies = ARRAY_SIZE(sc7280_supplies),
+	.clk_names = (const char **)sc7280_clks,
+	.num_clk = ARRAY_SIZE(sc7280_clks),
+	.timer_clk_name = "timer",
+	.opp_clk_name = "core",
+	.genpds = sc7280_genpds,
+	.num_genpds = ARRAY_SIZE(sc7280_genpds),
+};
diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
index 244e851ff24d..26ee5d9fa4c9 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
@@ -455,6 +455,7 @@ static int phy_qcom_mipi_csi2_probe(struct platform_device *pdev)
 
 static const struct of_device_id phy_qcom_mipi_csi2_of_match_table[] = {
 	{ .compatible	= "qcom,sa8775p-csi2-phy", .data = &mipi_csi2_dphy_sa8775p },
+	{ .compatible	= "qcom,sc7280-csi2-phy", .data = &mipi_csi2_dphy_sc7280 },
 	{ .compatible	= "qcom,x1e80100-csi2-phy", .data = &mipi_csi2_dphy_4nm_x1e },
 	{ }
 };
diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
index 5578741c0930..e2a346bcec89 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
@@ -97,5 +97,6 @@ struct mipi_csi2phy_device {
 
 extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_4nm_x1e;
 extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_sa8775p;
+extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_sc7280;
 
 #endif /* __PHY_QCOM_MIPI_CSI2_H__ */
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 1/5] dt-bindings: phy: qcom: Add common qcom,csi2-phy

[Krzysztof Kozlowski]

On 03/11/2026 22:41, Anusha Arun Nandi wrote:
> SA8775P, QCS8300 and SC7280 CSI2 PHYs are bit-for-bit identical in
> devicetree shape (ports, bus-type, data-lanes, operating-points-v2,
> clocks, single "top" power-domain, vdda-phy/vdda-pll supplies).
> 
> Describe all three with a single qcom,csi2-phy.yaml and a compatible
> oneOf, rather than one standalone schema per SoC. QCS8300 is further
> required to be paired with a qcom,sa8775p-csi2-phy fallback
> compatible, the same way other Qualcomm bindings express full
> hardware compatibility between two SoCs (see qcom,qusb2-phy.yaml);
> this lets the driver bind QCS8300 nodes via its qcom,sa8775p-csi2-phy
> match entry rather than carrying a duplicate one.
> 
> qcom,x1e80100-csi2-phy.yaml is a separate PHY with a different shape
> (3 clocks, 3 power-domains, different supply names, DPHY split-mode
> support) and is left untouched.
> 
> Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>

How is it possible? There was no such patch, this is basically v1.

If this is v2, please provide changelog and lore links pointing to the
review.

> Signed-off-by: Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>

Please use scripts/get_maintainers.pl to get a list of necessary people
and lists to CC. It might happen, that command when run on an older
kernel, gives you outdated entries. Therefore please be sure you base
your patches on recent Linux kernel.

Tools like b4 or scripts/get_maintainer.pl provide you proper list of
people, so fix your workflow. Tools might also fail if you work on some
ancient tree (don't, instead use mainline) or work on fork of kernel
(don't, instead use mainline). Just use b4 and everything should be
fine, although remember about `b4 prep --auto-to-cc` if you added new
patches to the patchset.

You missed at least devicetree list (maybe more), so this won't be
tested by automated tooling. Performing review on untested code might be
a waste of time.

Please kindly resend and include all necessary To/Cc entries.

Best regards,
Krzysztof

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 2/5] phy: qcom-mipi-csi2: Make timer and OPP clock names configurable

[Krzysztof Kozlowski]

On 03/11/2026 22:41, Anusha Arun Nandi wrote:
> The timer-clock lookup in phy_qcom_mipi_csi2_probe() and the OPP
> clkname passed to devm_pm_opp_set_clkname() were both hardcoded
> string literals sized to x1e80100 ("timer"/"core"). Add
> timer_clk_name/opp_clk_name to struct mipi_csi2phy_soc_cfg so each
> SoC can declare its own clock-name strings instead.
> 
> x1e80100's soc_cfg now declares "timer"/"core" explicitly; no
> behaviour change.
> 
> Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>

Where did it happen?

Best regards,
Krzysztof

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 5/5] phy: qcom-mipi-csi2: Add sc7280 D-PHY provider

[Krzysztof Kozlowski]

On 03/11/2026 22:41, Anusha Arun Nandi wrote:
> Add the SC7280 CSIPHY to the generic MIPI CSI2 PHY driver, 
> bound to a new "qcom,sc7280-csi2-phy" compatible
> and reusing the existing D-PHY 2-phase hw ops
> (phy_qcom_mipi_csi2_ops_3ph_1_0). The lane_regs_sc7280[] init
> sequence is the CSIPHY 5nm 2-phase 2.5Gbps 4-lane D-PHY register
> set ported from the legacy in-tree camss-csiphy-3ph-1-0.c table,
> with the entries that table left as do-not-program placeholders
> simply omitted here rather than carried as a new marker. The
> soc_cfg declares the core/timer clocks (matching x1e80100's and
> sa8775p's clock-names convention for this pair) and the
> vdda-phy/vdda-pll supplies.
> 
> Like x1e80100 and SA8775P, SC7280's CSIPHY core clock is OPP-scaled
> against the sensor's link frequency via the shared csiphy_opp_table
> in kodiak.dtsi, so opp_clk_name is set to "core" here too. SC7280's
> CSIPHY has a single power-domain, the Titan Top GDSC, matching
> camss.c's sc7280_resources.pd_name = "top" and kodiak.dtsi's
> existing camss node; it is not OPP-scaled, only kept enabled.
> 
> Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>

Where/When? Please provide lore links and proper changelog.

...

> +
> +static const char * const sc7280_clks[] = {
> +	"core",
> +	"timer",
> +};

What is the point of this array for each variant if all devices have the
same names? IOW, what is the point of patch #2?

Best regards,
Krzysztof

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 2/5] phy: qcom-mipi-csi2: Make timer and OPP clock names configurable

[Krzysztof Kozlowski]

On 03/11/2026 22:41, Anusha Arun Nandi wrote:
> The timer-clock lookup in phy_qcom_mipi_csi2_probe() and the OPP
> clkname passed to devm_pm_opp_set_clkname() were both hardcoded
> string literals sized to x1e80100 ("timer"/"core"). Add
> timer_clk_name/opp_clk_name to struct mipi_csi2phy_soc_cfg so each
> SoC can declare its own clock-name strings instead.


But they do not declare different names and they must NOT declare
different names.

This commit is completely pointless. What's more: you do not explain WHY
you are doing this in the first place.

Best regards,
Krzysztof

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 1/5] dt-bindings: phy: qcom: Add common qcom,csi2-phy

[Bryan O'Donoghue]

On 03/11/2026 21:41, Anusha Arun Nandi wrote:
> SA8775P, QCS8300 and SC7280 CSI2 PHYs are bit-for-bit identical in
> devicetree shape (ports, bus-type, data-lanes, operating-points-v2,
> clocks, single "top" power-domain, vdda-phy/vdda-pll supplies).
> 
> Describe all three with a single qcom,csi2-phy.yaml and a compatible
> oneOf, rather than one standalone schema per SoC. QCS8300 is further
> required to be paired with a qcom,sa8775p-csi2-phy fallback
> compatible, the same way other Qualcomm bindings express full
> hardware compatibility between two SoCs (see qcom,qusb2-phy.yaml);
> this lets the driver bind QCS8300 nodes via its qcom,sa8775p-csi2-phy
> match entry rather than carrying a duplicate one.
> 
> qcom,x1e80100-csi2-phy.yaml is a separate PHY with a different shape
> (3 clocks, 3 power-domains, different supply names, DPHY split-mode
> support) and is left untouched.
> 
> Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>
> Signed-off-by: Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
> ---
>   .../bindings/phy/qcom,csi2-phy.yaml           | 176 ++++++++++++++++++
>   1 file changed, 176 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/phy/qcom,csi2-phy.yaml
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,csi2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,csi2-phy.yaml
> new file mode 100644
> index 000000000000..5d25547528bd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,csi2-phy.yaml
> @@ -0,0 +1,176 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright (c) 2026 Qualcomm Innovation Center, Inc. All rights reserved.
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/qcom,csi2-phy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm CSI2 PHY
> +
> +maintainers:
> +  - Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
> +
> +description:
> +  Qualcomm MIPI CSI2 D-PHY. Connects MIPI CSI2 sensors to Qualcomm's Camera
> +  CSI Decoder.
> +
> +properties:
> +  compatible:
> +    oneOf:
> +      - enum:
> +          - qcom,sa8775p-csi2-phy
> +          - qcom,sc7280-csi2-phy
> +      - items:
> +          - enum:
> +              - qcom,qcs8300-csi2-phy
> +          - const: qcom,sa8775p-csi2-phy
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 2
> +
> +  clock-names:
> +    items:
> +      - const: core
> +      - const: timer
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  operating-points-v2: true
> +
> +  opp-table:
> +    type: object
> +
> +  power-domains:
> +    items:
> +      - description: Titan Top GDSC - Titan ISP Block, Global Distributed Switch Controller.
> +
> +  power-domain-names:
> +    items:
> +      - const: top
> +
> +  vdda-phy-supply:
> +    description: Phandle to PHY supply.
> +
> +  vdda-pll-supply:
> +    description: Phandle to PLL supply.

Why are we departing from vdda-0p9-supply and vdda-1p2-supply ?

Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml

> +
> +  ports:
> +    $ref: /schemas/graph.yaml#/properties/ports
> +
> +    properties:
> +      port@0:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        description:
> +          Sensor input. A single sensor is described by a single endpoint
> +          with one to four data lanes, numbered 1-4. The clock lane is
> +          position 0.

Since you've cloned and owned the yaml - you've also dropped the 
description of DPHY split mode.

> +
> +        unevaluatedProperties: false
> +
> +        properties:
> +          endpoint:
> +            $ref: /schemas/media/video-interfaces.yaml#
> +            unevaluatedProperties: false
> +            properties:
> +              bus-type:
> +                enum:
> +                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
> +                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
> +                default: 4
> +
> +              data-lanes:
> +                minItems: 1
> +                maxItems: 4
> +                items:
> +                  minimum: 1
> +                  maximum: 4
> +                description:
> +                  Data lane positions following this endpoint's clock
> +                  lane. Positions are a per-port logical numbering, not
> +                  package pad or ball positions.
> +
> +            required:
> +              - data-lanes
> +              - remote-endpoint

And then you've dropped the DPHY split mode defintion

NAK

Please either clone and own the whole DPHY split-mode circus or just 
modify the existing definition to include your new stuff.

> +
> +      port@1:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description: Output to the CAMSS CSID controller.
> +
> +    required:
> +      - port@0
> +      - port@1
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - clock-names
> +  - interrupts
> +  - operating-points-v2
> +  - power-domains
> +  - power-domain-names
> +  - vdda-phy-supply
> +  - vdda-pll-supply
> +  - ports
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/qcom,sa8775p-camcc.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/media/video-interfaces.h>
> +
> +    phy@ac9c000 {
> +        compatible = "qcom,sa8775p-csi2-phy";
> +        reg = <0x0ac9c000 0x2000>;
> +
> +        clocks = <&camcc CAM_CC_CSIPHY0_CLK>,
> +                 <&camcc CAM_CC_CSI0PHYTIMER_CLK>;
> +        clock-names = "core",
> +                      "timer";
> +
> +        interrupts = <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>;
> +
> +        operating-points-v2 = <&csiphy_opp_table>;
> +
> +        power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
> +        power-domain-names = "top";
> +
> +        vdda-phy-supply = <&vreg_l4a>;
> +        vdda-pll-supply = <&vreg_l1c>;
> +
> +        ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            port@0 {
> +                reg = <0>;
> +                csiphy0_in: endpoint {
> +                    bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
> +                    data-lanes = <1 2 3 4>;
> +                    remote-endpoint = <&sensor_out>;
> +                };
> +            };
> +
> +            port@1 {
> +                reg = <1>;
> +                csiphy0_out: endpoint {
> +                    remote-endpoint = <&csid_in>;
> +                };
> +            };
> +        };
> +
> +        csiphy_opp_table: opp-table {
> +            compatible = "operating-points-v2";
> +
> +            opp-300000000 {
> +                opp-hz = /bits/ 64 <300000000>;
> +            };
> +        };
> +    };
> --
> 2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy