[PATCH 0/6] phy: rockchip: samsung-hdptx: Clock fixes and API transition cleanups

[PATCH 0/6] phy: rockchip: samsung-hdptx: Clock fixes and API transition cleanups

[Cristian Ciocaltea]

This series provides a set of bug fixes and cleanups for the Rockchip
Samsung HDPTX PHY driver.

The first part of the series (i.e. PATCH 1 & 2) addresses clock rate
calculation and synchronization issues.  Specifically, it fixes edge
cases where the PHY PLL is pre-programmed by an external component (like
a bootloader) or when changing the color depth (bpc) while keeping the
modeline constant.  Because the Common Clock Framework .set_rate()
callback might not be invoked if the pixel clock remains unchanged, this
previously led to out-of-sync states between CCF and the actual HDMI PHY
configuration.

The second part focuses on code cleanups and modernizing the register
access.  Now that dw_hdmi_qp driver has fully switched to using
phy_configure(), we can drop the deprecated TMDS rate setup workarounds
and the restrict_rate_change flag logic.  Finally, it refactors the
driver to consistently use standard bitfield macros.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
---
Cristian Ciocaltea (6):
      phy: rockchip: samsung-hdptx: Fix rate recalculation for high bpc
      phy: rockchip: samsung-hdptx: Handle uncommitted PHY config changes
      phy: rockchip: samsung-hdptx: Drop TMDS rate setup workaround
      phy: rockchip: samsung-hdptx: Drop restrict_rate_change handling
      phy: rockchip: samsung-hdptx: Simplify GRF access with FIELD_PREP_WM16()
      phy: rockchip: samsung-hdptx: Consistently use bitfield macros

 drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 215 +++++++++-------------
 1 file changed, 92 insertions(+), 123 deletions(-)
---
base-commit: 7d6661873f6b54c75195780a40d66bad3d482d8f
change-id: 20260227-hdptx-clk-fixes-47426632f862


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 1/6] phy: rockchip: samsung-hdptx: Fix rate recalculation for high bpc

[Cristian Ciocaltea]

The PHY PLL can been programmed by an external component, e.g. the
bootloader, just before the recalc_rate() callback is invoked during
devm_clk_hw_register() in the probe path.

Therefore rk_hdptx_phy_clk_recalc_rate() finds the PLL enabled and
attempts to compute the clock rate, while making use of the bpc value
from the HDMI PHY configuration, which always defaults to 8 because
phy_configure() was not run at that point.  As a consequence, the
(re)calculated rate is incorrect when the actual bpc was higher than 8.

Do not rely on any of the hdmi_cfg members when computing the clock rate
and, instead, read the required input data (i.e. bpc), directly from the
hardware registers.

Fixes: 3481fc04d969 ("phy: rockchip: samsung-hdptx: Compute clk rate from PLL config")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
---
 drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 13 ++++---------
 1 file changed, 4 insertions(+), 9 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
index 2d973bc37f07..7fb1c22318bb 100644
--- a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
+++ b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
@@ -2168,7 +2168,7 @@ static u64 rk_hdptx_phy_clk_calc_rate_from_pll_cfg(struct rk_hdptx_phy *hdptx)
 	struct lcpll_config lcpll_hw;
 	struct ropll_config ropll_hw;
 	u64 fout, sdm;
-	u32 mode, val;
+	u32 mode, bpc, val;
 	int ret, i;
 
 	ret = regmap_read(hdptx->regmap, CMN_REG(0008), &mode);
@@ -2266,6 +2266,7 @@ static u64 rk_hdptx_phy_clk_calc_rate_from_pll_cfg(struct rk_hdptx_phy *hdptx)
 	if (ret)
 		return 0;
 	ropll_hw.pms_sdiv = ((val & PLL_PCG_POSTDIV_SEL_MASK) >> 4) + 1;
+	bpc = (FIELD_GET(PLL_PCG_CLK_SEL_MASK, val) << 1) + 8;
 
 	fout = PLL_REF_CLK * ropll_hw.pms_mdiv;
 	if (ropll_hw.sdm_en) {
@@ -2280,7 +2281,7 @@ static u64 rk_hdptx_phy_clk_calc_rate_from_pll_cfg(struct rk_hdptx_phy *hdptx)
 			fout = fout + sdm;
 	}
 
-	return div_u64(fout * 2, ropll_hw.pms_sdiv * 10);
+	return div_u64(fout * 2 * 8, ropll_hw.pms_sdiv * 10 * bpc);
 }
 
 static unsigned long rk_hdptx_phy_clk_recalc_rate(struct clk_hw *hw,
@@ -2288,19 +2289,13 @@ static unsigned long rk_hdptx_phy_clk_recalc_rate(struct clk_hw *hw,
 {
 	struct rk_hdptx_phy *hdptx = to_rk_hdptx_phy(hw);
 	u32 status;
-	u64 rate;
 	int ret;
 
 	ret = regmap_read(hdptx->grf, GRF_HDPTX_CON0, &status);
 	if (ret || !(status & HDPTX_I_PLL_EN))
 		return 0;
 
-	rate = rk_hdptx_phy_clk_calc_rate_from_pll_cfg(hdptx);
-
-	if (hdptx->hdmi_cfg.mode == PHY_HDMI_MODE_FRL)
-		return rate;
-
-	return DIV_ROUND_CLOSEST_ULL(rate * 8, hdptx->hdmi_cfg.bpc);
+	return rk_hdptx_phy_clk_calc_rate_from_pll_cfg(hdptx);
 }
 
 static int rk_hdptx_phy_clk_determine_rate(struct clk_hw *hw,

-- 
2.52.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 2/6] phy: rockchip: samsung-hdptx: Handle uncommitted PHY config changes

[Cristian Ciocaltea]

Any changes to the PHY link rate and/or color depth done via the HDMI
PHY configuration API are not immediately programmed into the hardware,
but are delayed until the PHY usage count gets incremented from 0 to 1,
that is when it is powered on or when the PLL clock exposed through
the CCF API is prepared, whichever comes first.

Since the clock might remain in prepared state after subsequent PHY
config changes, the programming can also be triggered via
clk_ops.set_rate().  However, from the clock consumer perspective (i.e.
VOP2 display controller), the (pixel) clock rate doesn't vary with bpc,
as that is handled internally by the PHY and reflected in the TDMS
character rate only.

As a consequence, changing the bpc while preserving the modeline may
lead to out-of-sync issues between CCF and HDMI PHY config state,
because the .set_rate() callback is not invoked when clock rate remains
constant.  This may also happen when the PHY PLL has been pre-programmed
by an external entity, e.g. the bootloader, which is actually a
regression introduced by the recent FRL patches.

Introduce a pll_config_dirty flag to keep track of uncommitted PHY
config changes and use it in clk_ops.determine_rate() to invalidate the
current clock rate (as known by CCF) and, consequently, ensure those
changes are programmed into hardware via clk_ops.set_rate().

Moreover, proceed with a similar fix in phy_ops.power_on() callback, to
handle the scenario where the CCF API is not used due to operating in
FRL mode, while the clock is still in a prepared state and thus
preventing rk_hdptx_phy_consumer_get() to apply the updated PHY
configuration.

Fixes: de5dba833118 ("phy: rockchip: samsung-hdptx: Add HDMI 2.1 FRL support")
Fixes: 9d0ec51d7c22 ("phy: rockchip: samsung-hdptx: Add high color depth management")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
---
 drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 86 ++++++++++++-----------
 1 file changed, 46 insertions(+), 40 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
index 7fb1c22318bb..14d266c8df5c 100644
--- a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
+++ b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
@@ -413,6 +413,7 @@ struct rk_hdptx_phy {
 
 	/* clk provider */
 	struct clk_hw hw;
+	bool pll_config_dirty;
 	bool restrict_rate_change;
 
 	atomic_t usage_count;
@@ -1260,13 +1261,19 @@ static int rk_hdptx_tmds_ropll_cmn_config(struct rk_hdptx_phy *hdptx)
 
 static int rk_hdptx_pll_cmn_config(struct rk_hdptx_phy *hdptx)
 {
+	int ret;
+
 	if (hdptx->hdmi_cfg.rate <= HDMI20_MAX_RATE)
-		return rk_hdptx_tmds_ropll_cmn_config(hdptx);
+		ret = rk_hdptx_tmds_ropll_cmn_config(hdptx);
+	else if (hdptx->hdmi_cfg.rate == FRL_8G4L_RATE)
+		ret = rk_hdptx_frl_lcpll_ropll_cmn_config(hdptx);
+	else
+		ret = rk_hdptx_frl_lcpll_cmn_config(hdptx);
 
-	if (hdptx->hdmi_cfg.rate == FRL_8G4L_RATE)
-		return rk_hdptx_frl_lcpll_ropll_cmn_config(hdptx);
+	if (!ret)
+		hdptx->pll_config_dirty = false;
 
-	return rk_hdptx_frl_lcpll_cmn_config(hdptx);
+	return ret;
 }
 
 static int rk_hdptx_frl_lcpll_mode_config(struct rk_hdptx_phy *hdptx)
@@ -1347,25 +1354,17 @@ static int rk_hdptx_phy_consumer_get(struct rk_hdptx_phy *hdptx)
 		return 0;
 
 	ret = regmap_read(hdptx->grf, GRF_HDPTX_STATUS, &status);
-	if (ret)
-		goto dec_usage;
-
-	if (status & HDPTX_O_PLL_LOCK_DONE)
-		dev_warn(hdptx->dev, "PLL locked by unknown consumer!\n");
+	if (ret) {
+		atomic_dec(&hdptx->usage_count);
+		return ret;
+	}
 
-	if (mode == PHY_MODE_DP) {
+	if (mode == PHY_MODE_DP)
 		rk_hdptx_dp_reset(hdptx);
-	} else {
-		ret = rk_hdptx_pll_cmn_config(hdptx);
-		if (ret)
-			goto dec_usage;
-	}
+	else
+		rk_hdptx_pll_cmn_config(hdptx);
 
 	return 0;
-
-dec_usage:
-	atomic_dec(&hdptx->usage_count);
-	return ret;
 }
 
 static int rk_hdptx_phy_consumer_put(struct rk_hdptx_phy *hdptx, bool force)
@@ -1700,16 +1699,20 @@ static int rk_hdptx_phy_power_on(struct phy *phy)
 		if (ret)
 			rk_hdptx_phy_consumer_put(hdptx, true);
 	} else {
-		regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-			     HDPTX_MODE_SEL << 16 | FIELD_PREP(HDPTX_MODE_SEL, 0x0));
+		if (hdptx->pll_config_dirty)
+			ret = rk_hdptx_pll_cmn_config(hdptx);
 
-		if (hdptx->hdmi_cfg.mode == PHY_HDMI_MODE_FRL)
-			ret = rk_hdptx_frl_lcpll_mode_config(hdptx);
-		else
-			ret = rk_hdptx_tmds_ropll_mode_config(hdptx);
+		if (!ret) {
+			regmap_write(hdptx->grf, GRF_HDPTX_CON0,
+				     HDPTX_MODE_SEL << 16 | FIELD_PREP(HDPTX_MODE_SEL, 0x0));
 
-		if (ret)
+			if (hdptx->hdmi_cfg.mode == PHY_HDMI_MODE_FRL)
+				ret = rk_hdptx_frl_lcpll_mode_config(hdptx);
+			else
+				ret = rk_hdptx_tmds_ropll_mode_config(hdptx);
+		} else {
 			rk_hdptx_phy_consumer_put(hdptx, true);
+		}
 	}
 
 	return ret;
@@ -2081,7 +2084,10 @@ static int rk_hdptx_phy_configure(struct phy *phy, union phy_configure_opts *opt
 			dev_err(hdptx->dev, "invalid hdmi params for phy configure\n");
 		} else {
 			hdptx->restrict_rate_change = true;
-			dev_dbg(hdptx->dev, "%s rate=%llu bpc=%u\n", __func__,
+			hdptx->pll_config_dirty = true;
+
+			dev_dbg(hdptx->dev, "%s %s rate=%llu bpc=%u\n", __func__,
+				hdptx->hdmi_cfg.mode ? "FRL" : "TMDS",
 				hdptx->hdmi_cfg.rate, hdptx->hdmi_cfg.bpc);
 		}
 
@@ -2303,8 +2309,19 @@ static int rk_hdptx_phy_clk_determine_rate(struct clk_hw *hw,
 {
 	struct rk_hdptx_phy *hdptx = to_rk_hdptx_phy(hw);
 
-	if (hdptx->hdmi_cfg.mode == PHY_HDMI_MODE_FRL)
-		return hdptx->hdmi_cfg.rate;
+	/*
+	 * Invalidate current clock rate to ensure rk_hdptx_phy_clk_set_rate()
+	 * will be invoked to commit PLL configuration.
+	 */
+	if (hdptx->pll_config_dirty) {
+		req->rate = 0;
+		return 0;
+	}
+
+	if (hdptx->hdmi_cfg.mode == PHY_HDMI_MODE_FRL) {
+		req->rate = hdptx->hdmi_cfg.rate;
+		return 0;
+	}
 
 	/*
 	 * FIXME: Temporarily allow altering TMDS char rate via CCF.
@@ -2336,17 +2353,6 @@ static int rk_hdptx_phy_clk_set_rate(struct clk_hw *hw, unsigned long rate,
 				     unsigned long parent_rate)
 {
 	struct rk_hdptx_phy *hdptx = to_rk_hdptx_phy(hw);
-	unsigned long long link_rate = rate;
-
-	if (hdptx->hdmi_cfg.mode != PHY_HDMI_MODE_FRL)
-		link_rate = DIV_ROUND_CLOSEST_ULL(rate * hdptx->hdmi_cfg.bpc, 8);
-
-	/* Revert any unlikely link rate change since determine_rate() */
-	if (hdptx->hdmi_cfg.rate != link_rate) {
-		dev_warn(hdptx->dev, "Reverting unexpected rate change from %llu to %llu\n",
-			 link_rate, hdptx->hdmi_cfg.rate);
-		hdptx->hdmi_cfg.rate = link_rate;
-	}
 
 	/*
 	 * The link rate would be normally programmed in HW during

-- 
2.52.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 3/6] phy: rockchip: samsung-hdptx: Drop TMDS rate setup workaround

[Cristian Ciocaltea]

Since commit ba9c2fe18c17 ("drm/rockchip: dw_hdmi_qp: Switch to
phy_configure()") the TMDS rate setup doesn't rely anymore on the
unconventional usage of the bus width, instead it is managed exclusively
through the HDMI PHY configuration API.

Drop the now obsolete workaround to retrieve the TMDS character rate via
phy_get_bus_width() during power_on().

While at it, get rid of the extra call to rk_hdptx_phy_consumer_put() by
moving the statement at the end of the function.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
---
 drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 26 ++++++-----------------
 1 file changed, 6 insertions(+), 20 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
index 14d266c8df5c..b56360b5df78 100644
--- a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
+++ b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
@@ -1655,22 +1655,6 @@ static int rk_hdptx_phy_power_on(struct phy *phy)
 	enum phy_mode mode = phy_get_mode(phy);
 	int ret, lane;
 
-	if (mode != PHY_MODE_DP) {
-		if (!hdptx->hdmi_cfg.rate && hdptx->hdmi_cfg.mode != PHY_HDMI_MODE_FRL) {
-			/*
-			 * FIXME: Temporary workaround to setup TMDS char rate
-			 * from the RK DW HDMI QP bridge driver.
-			 * Will be removed as soon the switch to the HDMI PHY
-			 * configuration API has been completed on both ends.
-			 */
-			hdptx->hdmi_cfg.rate = phy_get_bus_width(hdptx->phy) & 0xfffffff;
-			hdptx->hdmi_cfg.rate *= 100;
-		}
-
-		dev_dbg(hdptx->dev, "%s rate=%llu bpc=%u\n", __func__,
-			hdptx->hdmi_cfg.rate, hdptx->hdmi_cfg.bpc);
-	}
-
 	ret = rk_hdptx_phy_consumer_get(hdptx);
 	if (ret)
 		return ret;
@@ -1696,9 +1680,10 @@ static int rk_hdptx_phy_power_on(struct phy *phy)
 		rk_hdptx_dp_pll_init(hdptx);
 
 		ret = rk_hdptx_dp_aux_init(hdptx);
-		if (ret)
-			rk_hdptx_phy_consumer_put(hdptx, true);
 	} else {
+		dev_dbg(hdptx->dev, "%s rate=%llu bpc=%u\n", __func__,
+			hdptx->hdmi_cfg.rate, hdptx->hdmi_cfg.bpc);
+
 		if (hdptx->pll_config_dirty)
 			ret = rk_hdptx_pll_cmn_config(hdptx);
 
@@ -1710,11 +1695,12 @@ static int rk_hdptx_phy_power_on(struct phy *phy)
 				ret = rk_hdptx_frl_lcpll_mode_config(hdptx);
 			else
 				ret = rk_hdptx_tmds_ropll_mode_config(hdptx);
-		} else {
-			rk_hdptx_phy_consumer_put(hdptx, true);
 		}
 	}
 
+	if (ret)
+		rk_hdptx_phy_consumer_put(hdptx, true);
+
 	return ret;
 }
 

-- 
2.52.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 4/6] phy: rockchip: samsung-hdptx: Drop restrict_rate_change handling

[Cristian Ciocaltea]

Since commit 6efbd0f46dd8 ("phy: rockchip: samsung-hdptx: Restrict
altering TMDS char rate via CCF"), adjusting the rate via the Common
Clock Framework API has been disallowed.

To avoid breaking existing users until switching to the PHY config API,
it introduced a temporary exception to the rule, controlled via the
'restrict_rate_change' flag.

As the API transition completed, remove the now deprecated exception
logic.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
---
 drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 42 +++++------------------
 1 file changed, 8 insertions(+), 34 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
index b56360b5df78..e5c8bc95a416 100644
--- a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
+++ b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
@@ -414,7 +414,6 @@ struct rk_hdptx_phy {
 	/* clk provider */
 	struct clk_hw hw;
 	bool pll_config_dirty;
-	bool restrict_rate_change;
 
 	atomic_t usage_count;
 
@@ -2069,7 +2068,6 @@ static int rk_hdptx_phy_configure(struct phy *phy, union phy_configure_opts *opt
 		if (ret) {
 			dev_err(hdptx->dev, "invalid hdmi params for phy configure\n");
 		} else {
-			hdptx->restrict_rate_change = true;
 			hdptx->pll_config_dirty = true;
 
 			dev_dbg(hdptx->dev, "%s %s rate=%llu bpc=%u\n", __func__,
@@ -2296,41 +2294,17 @@ static int rk_hdptx_phy_clk_determine_rate(struct clk_hw *hw,
 	struct rk_hdptx_phy *hdptx = to_rk_hdptx_phy(hw);
 
 	/*
-	 * Invalidate current clock rate to ensure rk_hdptx_phy_clk_set_rate()
-	 * will be invoked to commit PLL configuration.
+	 * For uncommitted PLL configuration, invalidate the current clock rate
+	 * to ensure rk_hdptx_phy_clk_set_rate() will be always invoked.
+	 * Otherwise, restrict the rate according to the PHY link setup.
 	 */
-	if (hdptx->pll_config_dirty) {
+	if (hdptx->pll_config_dirty)
 		req->rate = 0;
-		return 0;
-	}
-
-	if (hdptx->hdmi_cfg.mode == PHY_HDMI_MODE_FRL) {
+	else if (hdptx->hdmi_cfg.mode == PHY_HDMI_MODE_FRL)
 		req->rate = hdptx->hdmi_cfg.rate;
-		return 0;
-	}
-
-	/*
-	 * FIXME: Temporarily allow altering TMDS char rate via CCF.
-	 * To be dropped as soon as the RK DW HDMI QP bridge driver
-	 * switches to make use of phy_configure().
-	 */
-	if (!hdptx->restrict_rate_change && req->rate != hdptx->hdmi_cfg.rate) {
-		struct phy_configure_opts_hdmi hdmi = {
-			.tmds_char_rate = req->rate,
-		};
-
-		int ret = rk_hdptx_phy_verify_hdmi_config(hdptx, &hdmi, &hdptx->hdmi_cfg);
-
-		if (ret)
-			return ret;
-	}
-
-	/*
-	 * The TMDS char rate shall be adjusted via phy_configure() only,
-	 * hence ensure rk_hdptx_phy_clk_set_rate() won't be invoked with
-	 * a different rate argument.
-	 */
-	req->rate = DIV_ROUND_CLOSEST_ULL(hdptx->hdmi_cfg.rate * 8, hdptx->hdmi_cfg.bpc);
+	else
+		req->rate = DIV_ROUND_CLOSEST_ULL(hdptx->hdmi_cfg.rate * 8,
+						  hdptx->hdmi_cfg.bpc);
 
 	return 0;
 }

-- 
2.52.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 5/6] phy: rockchip: samsung-hdptx: Simplify GRF access with FIELD_PREP_WM16()

[Cristian Ciocaltea]

The 16 most significant bits of the general-purpose register (GRF) are
used as a write-enable mask for the remaining 16 bits.

Make use of the recently introduced FIELD_PREP_WM16() macro to avoid
open-coding the bit shift operations and improve code readability.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
---
 drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 52 +++++++++++------------
 1 file changed, 25 insertions(+), 27 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
index e5c8bc95a416..baa6916331be 100644
--- a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
+++ b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Copyright (c) 2021-2022 Rockchip Electronics Co., Ltd.
- * Copyright (c) 2024 Collabora Ltd.
+ * Copyright (c) 2024-2026 Collabora Ltd.
  *
  * Author: Algea Cao <algea.cao@rock-chips.com>
  * Author: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
@@ -10,6 +10,7 @@
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
 #include <linux/delay.h>
+#include <linux/hw_bitfield.h>
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -949,7 +950,9 @@ static void rk_hdptx_pre_power_up(struct rk_hdptx_phy *hdptx)
 	reset_control_assert(hdptx->rsts[RST_CMN].rstc);
 	reset_control_assert(hdptx->rsts[RST_INIT].rstc);
 
-	val = (HDPTX_I_PLL_EN | HDPTX_I_BIAS_EN | HDPTX_I_BGR_EN) << 16;
+	val = (FIELD_PREP_WM16(HDPTX_I_PLL_EN, 0) |
+	       FIELD_PREP_WM16(HDPTX_I_BIAS_EN, 0) |
+	       FIELD_PREP_WM16(HDPTX_I_BGR_EN, 0));
 	regmap_write(hdptx->grf, GRF_HDPTX_CON0, val);
 }
 
@@ -960,8 +963,8 @@ static int rk_hdptx_post_enable_lane(struct rk_hdptx_phy *hdptx)
 
 	reset_control_deassert(hdptx->rsts[RST_LANE].rstc);
 
-	val = (HDPTX_I_BIAS_EN | HDPTX_I_BGR_EN) << 16 |
-	       HDPTX_I_BIAS_EN | HDPTX_I_BGR_EN;
+	val = (FIELD_PREP_WM16(HDPTX_I_BIAS_EN, 1) |
+	       FIELD_PREP_WM16(HDPTX_I_BGR_EN, 1));
 	regmap_write(hdptx->grf, GRF_HDPTX_CON0, val);
 
 	/* 3 lanes FRL mode */
@@ -990,16 +993,15 @@ static int rk_hdptx_post_enable_pll(struct rk_hdptx_phy *hdptx)
 	u32 val;
 	int ret;
 
-	val = (HDPTX_I_BIAS_EN | HDPTX_I_BGR_EN) << 16 |
-	       HDPTX_I_BIAS_EN | HDPTX_I_BGR_EN;
+	val = (FIELD_PREP_WM16(HDPTX_I_BIAS_EN, 1) |
+	       FIELD_PREP_WM16(HDPTX_I_BGR_EN, 1));
 	regmap_write(hdptx->grf, GRF_HDPTX_CON0, val);
 
 	usleep_range(10, 15);
 	reset_control_deassert(hdptx->rsts[RST_INIT].rstc);
 
 	usleep_range(10, 15);
-	val = HDPTX_I_PLL_EN << 16 | HDPTX_I_PLL_EN;
-	regmap_write(hdptx->grf, GRF_HDPTX_CON0, val);
+	regmap_write(hdptx->grf, GRF_HDPTX_CON0, FIELD_PREP_WM16(HDPTX_I_PLL_EN, 1));
 
 	usleep_range(10, 15);
 	reset_control_deassert(hdptx->rsts[RST_CMN].rstc);
@@ -1037,7 +1039,9 @@ static void rk_hdptx_phy_disable(struct rk_hdptx_phy *hdptx)
 	reset_control_assert(hdptx->rsts[RST_CMN].rstc);
 	reset_control_assert(hdptx->rsts[RST_INIT].rstc);
 
-	val = (HDPTX_I_PLL_EN | HDPTX_I_BIAS_EN | HDPTX_I_BGR_EN) << 16;
+	val = (FIELD_PREP_WM16(HDPTX_I_PLL_EN, 0) |
+	       FIELD_PREP_WM16(HDPTX_I_BIAS_EN, 0) |
+	       FIELD_PREP_WM16(HDPTX_I_BGR_EN, 0));
 	regmap_write(hdptx->grf, GRF_HDPTX_CON0, val);
 }
 
@@ -1135,7 +1139,7 @@ static int rk_hdptx_frl_lcpll_cmn_config(struct rk_hdptx_phy *hdptx)
 
 	rk_hdptx_pre_power_up(hdptx);
 
-	regmap_write(hdptx->grf, GRF_HDPTX_CON0, LC_REF_CLK_SEL << 16);
+	regmap_write(hdptx->grf, GRF_HDPTX_CON0, FIELD_PREP_WM16(LC_REF_CLK_SEL, 0));
 
 	rk_hdptx_multi_reg_write(hdptx, rk_hdptx_common_cmn_init_seq);
 	rk_hdptx_multi_reg_write(hdptx, rk_hdptx_frl_lcpll_cmn_init_seq);
@@ -1178,8 +1182,7 @@ static int rk_hdptx_frl_lcpll_ropll_cmn_config(struct rk_hdptx_phy *hdptx)
 	rk_hdptx_pre_power_up(hdptx);
 
 	/* ROPLL input reference clock from LCPLL (cascade mode) */
-	regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-		     (LC_REF_CLK_SEL << 16) | LC_REF_CLK_SEL);
+	regmap_write(hdptx->grf, GRF_HDPTX_CON0, FIELD_PREP_WM16(LC_REF_CLK_SEL, 1));
 
 	rk_hdptx_multi_reg_write(hdptx, rk_hdptx_common_cmn_init_seq);
 	rk_hdptx_multi_reg_write(hdptx, rk_hdptx_frl_lcpll_ropll_cmn_init_seq);
@@ -1218,7 +1221,7 @@ static int rk_hdptx_tmds_ropll_cmn_config(struct rk_hdptx_phy *hdptx)
 
 	rk_hdptx_pre_power_up(hdptx);
 
-	regmap_write(hdptx->grf, GRF_HDPTX_CON0, LC_REF_CLK_SEL << 16);
+	regmap_write(hdptx->grf, GRF_HDPTX_CON0, FIELD_PREP_WM16(LC_REF_CLK_SEL, 0));
 
 	rk_hdptx_multi_reg_write(hdptx, rk_hdptx_common_cmn_init_seq);
 	rk_hdptx_multi_reg_write(hdptx, rk_hdptx_tmds_cmn_init_seq);
@@ -1336,11 +1339,9 @@ static void rk_hdptx_dp_reset(struct rk_hdptx_phy *hdptx)
 			   FIELD_PREP(LN_TX_DRV_EI_EN_MASK, 0));
 
 	regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-		     HDPTX_I_PLL_EN << 16 | FIELD_PREP(HDPTX_I_PLL_EN, 0x0));
-	regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-		     HDPTX_I_BIAS_EN << 16 | FIELD_PREP(HDPTX_I_BIAS_EN, 0x0));
-	regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-		     HDPTX_I_BGR_EN << 16 | FIELD_PREP(HDPTX_I_BGR_EN, 0x0));
+		     FIELD_PREP_WM16(HDPTX_I_PLL_EN, 0) |
+		     FIELD_PREP_WM16(HDPTX_I_BIAS_EN, 0) |
+		     FIELD_PREP_WM16(HDPTX_I_BGR_EN, 0));
 }
 
 static int rk_hdptx_phy_consumer_get(struct rk_hdptx_phy *hdptx)
@@ -1611,9 +1612,8 @@ static int rk_hdptx_dp_aux_init(struct rk_hdptx_phy *hdptx)
 			   FIELD_PREP(OVRD_SB_VREG_EN_MASK, 0x1));
 
 	regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-		     HDPTX_I_BGR_EN << 16 | FIELD_PREP(HDPTX_I_BGR_EN, 0x1));
-	regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-		     HDPTX_I_BIAS_EN << 16 | FIELD_PREP(HDPTX_I_BIAS_EN, 0x1));
+		     FIELD_PREP_WM16(HDPTX_I_BGR_EN, 1) |
+		     FIELD_PREP_WM16(HDPTX_I_BIAS_EN, 1));
 	usleep_range(20, 25);
 
 	reset_control_deassert(hdptx->rsts[RST_INIT].rstc);
@@ -1660,7 +1660,7 @@ static int rk_hdptx_phy_power_on(struct phy *phy)
 
 	if (mode == PHY_MODE_DP) {
 		regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-			     HDPTX_MODE_SEL << 16 | FIELD_PREP(HDPTX_MODE_SEL, 0x1));
+			     FIELD_PREP_WM16(HDPTX_MODE_SEL, 1));
 
 		for (lane = 0; lane < 4; lane++) {
 			regmap_update_bits(hdptx->regmap, LANE_REG(031e) + 0x400 * lane,
@@ -1688,7 +1688,7 @@ static int rk_hdptx_phy_power_on(struct phy *phy)
 
 		if (!ret) {
 			regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-				     HDPTX_MODE_SEL << 16 | FIELD_PREP(HDPTX_MODE_SEL, 0x0));
+				     FIELD_PREP_WM16(HDPTX_MODE_SEL, 0));
 
 			if (hdptx->hdmi_cfg.mode == PHY_HDMI_MODE_FRL)
 				ret = rk_hdptx_frl_lcpll_mode_config(hdptx);
@@ -1823,8 +1823,7 @@ static int rk_hdptx_phy_set_rate(struct rk_hdptx_phy *hdptx,
 	u32 bw, status;
 	int ret;
 
-	regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-		     HDPTX_I_PLL_EN << 16 | FIELD_PREP(HDPTX_I_PLL_EN, 0x0));
+	regmap_write(hdptx->grf, GRF_HDPTX_CON0, FIELD_PREP_WM16(HDPTX_I_PLL_EN, 0));
 
 	switch (dp->link_rate) {
 	case 1620:
@@ -1880,8 +1879,7 @@ static int rk_hdptx_phy_set_rate(struct rk_hdptx_phy *hdptx,
 	regmap_update_bits(hdptx->regmap, CMN_REG(0095), DP_TX_LINK_BW_MASK,
 			   FIELD_PREP(DP_TX_LINK_BW_MASK, bw));
 
-	regmap_write(hdptx->grf, GRF_HDPTX_CON0,
-		     HDPTX_I_PLL_EN << 16 | FIELD_PREP(HDPTX_I_PLL_EN, 0x1));
+	regmap_write(hdptx->grf, GRF_HDPTX_CON0, FIELD_PREP_WM16(HDPTX_I_PLL_EN, 1));
 
 	ret = regmap_read_poll_timeout(hdptx->grf, GRF_HDPTX_STATUS,
 				       status, FIELD_GET(HDPTX_O_PLL_LOCK_DONE, status),

-- 
2.52.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 6/6] phy: rockchip: samsung-hdptx: Consistently use bitfield macros

[Cristian Ciocaltea]

Make the code more robust and improve readability by using the available
bitfield macros (e.g. FIELD_PREP, FIELD_GET) whenever possible, instead
of open coding the related bit operations.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
---
 drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 22 ++++++++++++++++------
 1 file changed, 16 insertions(+), 6 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
index baa6916331be..3bde7fbb34b1 100644
--- a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
+++ b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
@@ -53,6 +53,12 @@
 /* CMN_REG(001e) */
 #define LCPLL_PI_EN_MASK		BIT(5)
 #define LCPLL_100M_CLK_EN_MASK		BIT(0)
+/* CMN_REG(0022) */
+#define ANA_LCPLL_PMS_PDIV_MASK		GENMASK(7, 4)
+#define ANA_LCPLL_PMS_REFDIV_MASK	GENMASK(3, 0)
+/* CMN_REG(0023) */
+#define LCPLL_PMS_SDIV_RBR_MASK		GENMASK(7, 4)
+#define LCPLL_PMS_SDIV_HBR_MASK		GENMASK(3, 0)
 /* CMN_REG(0025) */
 #define LCPLL_PMS_IQDIV_RSTN_MASK	BIT(4)
 /* CMN_REG(0028) */
@@ -1157,9 +1163,11 @@ static int rk_hdptx_frl_lcpll_cmn_config(struct rk_hdptx_phy *hdptx)
 	regmap_write(hdptx->regmap, CMN_REG(0020), cfg->pms_mdiv);
 	regmap_write(hdptx->regmap, CMN_REG(0021), cfg->pms_mdiv_afc);
 	regmap_write(hdptx->regmap, CMN_REG(0022),
-		     (cfg->pms_pdiv << 4) | cfg->pms_refdiv);
+		     FIELD_PREP(ANA_LCPLL_PMS_PDIV_MASK, cfg->pms_pdiv) |
+		     FIELD_PREP(ANA_LCPLL_PMS_REFDIV_MASK, cfg->pms_refdiv));
 	regmap_write(hdptx->regmap, CMN_REG(0023),
-		     (cfg->pms_sdiv << 4) | cfg->pms_sdiv);
+		     FIELD_PREP(LCPLL_PMS_SDIV_RBR_MASK, cfg->pms_sdiv) |
+		     FIELD_PREP(LCPLL_PMS_SDIV_HBR_MASK, cfg->pms_sdiv));
 	regmap_write(hdptx->regmap, CMN_REG(002a), cfg->sdm_deno);
 	regmap_write(hdptx->regmap, CMN_REG(002b), cfg->sdm_num_sign);
 	regmap_write(hdptx->regmap, CMN_REG(002c), cfg->sdm_num);
@@ -1229,8 +1237,10 @@ static int rk_hdptx_tmds_ropll_cmn_config(struct rk_hdptx_phy *hdptx)
 	regmap_write(hdptx->regmap, CMN_REG(0051), cfg->pms_mdiv);
 	regmap_write(hdptx->regmap, CMN_REG(0055), cfg->pms_mdiv_afc);
 	regmap_write(hdptx->regmap, CMN_REG(0059),
-		     (cfg->pms_pdiv << 4) | cfg->pms_refdiv);
-	regmap_write(hdptx->regmap, CMN_REG(005a), cfg->pms_sdiv << 4);
+		     FIELD_PREP(ANA_ROPLL_PMS_PDIV_MASK, cfg->pms_pdiv) |
+		     FIELD_PREP(ANA_ROPLL_PMS_REFDIV_MASK, cfg->pms_refdiv));
+	regmap_write(hdptx->regmap, CMN_REG(005a),
+		     FIELD_PREP(ROPLL_PMS_SDIV_RBR_MASK, cfg->pms_sdiv));
 
 	regmap_update_bits(hdptx->regmap, CMN_REG(005e), ROPLL_SDM_EN_MASK,
 			   FIELD_PREP(ROPLL_SDM_EN_MASK, cfg->sdm_en));
@@ -2192,7 +2202,7 @@ static u64 rk_hdptx_phy_clk_calc_rate_from_pll_cfg(struct rk_hdptx_phy *hdptx)
 		ret = regmap_read(hdptx->regmap, CMN_REG(002D), &val);
 		if (ret)
 			return 0;
-		lcpll_hw.sdc_n = (val & LCPLL_SDC_N_MASK) >> 1;
+		lcpll_hw.sdc_n = FIELD_GET(LCPLL_SDC_N_MASK, val);
 
 		for (i = 0; i < ARRAY_SIZE(rk_hdptx_frl_lcpll_cfg); i++) {
 			const struct lcpll_config *cfg = &rk_hdptx_frl_lcpll_cfg[i];
@@ -2253,7 +2263,7 @@ static u64 rk_hdptx_phy_clk_calc_rate_from_pll_cfg(struct rk_hdptx_phy *hdptx)
 	ret = regmap_read(hdptx->regmap, CMN_REG(0086), &val);
 	if (ret)
 		return 0;
-	ropll_hw.pms_sdiv = ((val & PLL_PCG_POSTDIV_SEL_MASK) >> 4) + 1;
+	ropll_hw.pms_sdiv = FIELD_GET(PLL_PCG_POSTDIV_SEL_MASK, val) + 1;
 	bpc = (FIELD_GET(PLL_PCG_CLK_SEL_MASK, val) << 1) + 8;
 
 	fout = PLL_REF_CLK * ropll_hw.pms_mdiv;

-- 
2.52.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH 0/6] phy: rockchip: samsung-hdptx: Clock fixes and API transition cleanups

[1und1]

Hi Cristian,

Am Freitag, dem 27.02.2026 um 22:48 +0200 schrieb Cristian Ciocaltea:
> This series provides a set of bug fixes and cleanups for the Rockchip
> Samsung HDPTX PHY driver.
> 
> The first part of the series (i.e. PATCH 1 & 2) addresses clock rate
> calculation and synchronization issues.  Specifically, it fixes edge
> cases where the PHY PLL is pre-programmed by an external component (like
> a bootloader) or when changing the color depth (bpc) while keeping the
> modeline constant. 

as I brought up one of the mentioned edge cases with my Radxa Rock 5b booting
linux from EDK2 [1], I wanted to report that with this series applied,
everything works as expected and my issues are fixed.

Thus, feel free to add my

Tested-by: Thomas Niederprüm <dubito@online.de>

>  Because the Common Clock Framework .set_rate()
> callback might not be invoked if the pixel clock remains unchanged, this
> previously led to out-of-sync states between CCF and the actual HDMI PHY
> configuration.
> 
> The second part focuses on code cleanups and modernizing the register
> access.  Now that dw_hdmi_qp driver has fully switched to using
> phy_configure(), we can drop the deprecated TMDS rate setup workarounds
> and the restrict_rate_change flag logic.  Finally, it refactors the
> driver to consistently use standard bitfield macros.
> 
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
> ---
> Cristian Ciocaltea (6):
>       phy: rockchip: samsung-hdptx: Fix rate recalculation for high bpc
>       phy: rockchip: samsung-hdptx: Handle uncommitted PHY config changes
>       phy: rockchip: samsung-hdptx: Drop TMDS rate setup workaround
>       phy: rockchip: samsung-hdptx: Drop restrict_rate_change handling
>       phy: rockchip: samsung-hdptx: Simplify GRF access with FIELD_PREP_WM16()
>       phy: rockchip: samsung-hdptx: Consistently use bitfield macros
> 
>  drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 215 +++++++++------------
> -
>  1 file changed, 92 insertions(+), 123 deletions(-)
> ---
> base-commit: 7d6661873f6b54c75195780a40d66bad3d482d8f
> change-id: 20260227-hdptx-clk-fixes-47426632f862
> 
> 
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip

Best regards,

Thomas

[1]:
https://lore.kernel.org/lkml/b32164001947ba922aefb6ca86a8dc59e9323d2b.camel@online.de/

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH 0/6] phy: rockchip: samsung-hdptx: Clock fixes and API transition cleanups

[Cristian Ciocaltea]

Hi Thomas,

On 3/2/26 9:46 PM, 1und1 wrote:
> Hi Cristian,
> 
> Am Freitag, dem 27.02.2026 um 22:48 +0200 schrieb Cristian Ciocaltea:
>> This series provides a set of bug fixes and cleanups for the Rockchip
>> Samsung HDPTX PHY driver.
>>
>> The first part of the series (i.e. PATCH 1 & 2) addresses clock rate
>> calculation and synchronization issues.  Specifically, it fixes edge
>> cases where the PHY PLL is pre-programmed by an external component (like
>> a bootloader) or when changing the color depth (bpc) while keeping the
>> modeline constant. 
> 
> as I brought up one of the mentioned edge cases with my Radxa Rock 5b booting
> linux from EDK2 [1], I wanted to report that with this series applied,
> everything works as expected and my issues are fixed.
> 
> Thus, feel free to add my
> 
> Tested-by: Thomas Niederprüm <dubito@online.de>

Thanks for (re)testing!

Regards,
Cristian

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH 0/6] phy: rockchip: samsung-hdptx: Clock fixes and API transition cleanups

[Simon Wright]

Tested on R76S (RK3576) + LG G3 OLED at 1920x1080@60 bpc=10
(tmds_char_rate = 185625000): phy_configure / phy_power_on /
atomic_enable consistent end-to-end, no rate recalculation drift.
Matches the cover letter behaviour.

Heiko, Vinod -- any chance the series can be applied?

Tested-by: Simon Wright <simon@symple.nz>

Regards,
Simon
Symple Solutions, Dunedin, New Zealand

On 28/02/2026 9:48 am, Cristian Ciocaltea wrote:
> This series provides a set of bug fixes and cleanups for the Rockchip
> Samsung HDPTX PHY driver.
>
> The first part of the series (i.e. PATCH 1 & 2) addresses clock rate
> calculation and synchronization issues.  Specifically, it fixes edge
> cases where the PHY PLL is pre-programmed by an external component (like
> a bootloader) or when changing the color depth (bpc) while keeping the
> modeline constant.  Because the Common Clock Framework .set_rate()
> callback might not be invoked if the pixel clock remains unchanged, this
> previously led to out-of-sync states between CCF and the actual HDMI PHY
> configuration.
>
> The second part focuses on code cleanups and modernizing the register
> access.  Now that dw_hdmi_qp driver has fully switched to using
> phy_configure(), we can drop the deprecated TMDS rate setup workarounds
> and the restrict_rate_change flag logic.  Finally, it refactors the
> driver to consistently use standard bitfield macros.
>
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
> ---
> Cristian Ciocaltea (6):
>        phy: rockchip: samsung-hdptx: Fix rate recalculation for high bpc
>        phy: rockchip: samsung-hdptx: Handle uncommitted PHY config changes
>        phy: rockchip: samsung-hdptx: Drop TMDS rate setup workaround
>        phy: rockchip: samsung-hdptx: Drop restrict_rate_change handling
>        phy: rockchip: samsung-hdptx: Simplify GRF access with FIELD_PREP_WM16()
>        phy: rockchip: samsung-hdptx: Consistently use bitfield macros
>
>   drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 215 +++++++++-------------
>   1 file changed, 92 insertions(+), 123 deletions(-)
> ---
> base-commit: 7d6661873f6b54c75195780a40d66bad3d482d8f
> change-id: 20260227-hdptx-clk-fixes-47426632f862
>
>
>  From mboxrd@z Thu Jan  1 00:00:00 1970
> Return-Path: <linux-rockchip-bounces+linux-rockchip=archiver.kernel.org@lists.infradead.org>
> X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on
> 	aws-us-west-2-korg-lkml-1.web.codeaurora.org
> Received: from bombadil.infradead.org (bombadil.infradead.org [198.137.202.133])
> 	(using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits))
> 	(No client certificate requested)
> 	by smtp.lore.kernel.org (Postfix) with ESMTPS id 0EFFEFEFB51
> 	for <linux-rockchip@archiver.kernel.org>; Fri, 27 Feb 2026 20:49:16 +0000 (UTC)
> DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
> 	d=lists.infradead.org; s=bombadil.20210309; h=Sender:
> 	Content-Transfer-Encoding:Content-Type:List-Subscribe:List-Help:List-Post:
> 	List-Archive:List-Unsubscribe:List-Id:Cc:To:MIME-Version:Message-Id:Date:
> 	Subject:From:Reply-To:Content-ID:Content-Description:Resent-Date:Resent-From:
> 	Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID:In-Reply-To:References:
> 	List-Owner; bh=Ywd4nVTaesoZ9f/oRKu2xquW31o52EzvH6PggS2DIuY=; b=j/lxIwygT6ELX9
> 	QE4bInNEKLy6Q4slo+6T/r/kAeI+wNaYkSzqgLXJEscAMQtrus+adIdPOaL7GZ2IkbAd8RcVdU4j9
> 	uX5XMp7/ITC/8tA/4fbQMpj+0DiQJuSOe4mfEMQx3v7hnsb1kiFYgQWCOdy6U/zr6RtAlrrVa5WtH
> 	xu9XxBU9eqvpRmEAFS+fCZgIeb2lMqXHZ4NA4/pQLDEGN43Z4/owzoVcuqgbGjCvC9c4VfUrqUrSA
> 	tj/YDJr0SNYK4ZOKt1sVO78NRvcFhkl8ChuuV/iO5wrS0w565H6YGiFuJh1kQAYaFkwG7+Zn8DNF5
> 	fFppXc21VbuPRSwYyI+A==;
> Received: from localhost ([::1] helo=bombadil.infradead.org)
> 	by bombadil.infradead.org with esmtp (Exim 4.98.2 #2 (Red Hat Linux))
> 	id 1vw4lg-000000098cW-05gk;
> 	Fri, 27 Feb 2026 20:49:00 +0000
> Received: from bali.collaboradmins.com ([2a01:4f8:201:9162::2])
> 	by bombadil.infradead.org with esmtps (Exim 4.98.2 #2 (Red Hat Linux))
> 	id 1vw4lc-000000098ZS-2DwJ;
> 	Fri, 27 Feb 2026 20:48:57 +0000
> DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/simple; d=collabora.com;
> 	s=mail; t=1772225331;
> 	bh=bUeULh1bnVKovxRmlxehE6KS7aqNBCqPFyvaWOEsoaE=;
> 	h=From:Subject:Date:To:Cc:From;
> 	b=ekEaWw1uHuEz0iWpTlf7zG60N1dzqsUimUI0n7bx/xvqftKi5TS1D3FCMNmggdH15
> 	 nip240uzI3bC+sOV8/OHY8BKzO+U3KESiaX+LJuDTU5hdz/nyF19JOtVbOpEUwy2H2
> 	 nFG6mRz4JB6hSMOKVCGAxx27/gF8KCMaI21JIexzBmepPZApw6kf+9mFzcd2NqJPpe
> 	 kLTjON2UczI2jLr009ZWvx9fb2AVXa6s6axkOohMwRy+ggic0yZzQ7Pxjjdm6IZqcQ
> 	 ZtkEM8UHO29BkkEAX61miqbj6HTB7BAWlet6Q1SF2oqLc452ZSEViEuj67tw8dzuBz
> 	 E7iPV6xRgfL3g==
> Received: from localhost (unknown [86.123.23.225])
> 	(using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits)
> 	 key-exchange ECDHE (prime256v1) server-signature RSA-PSS (4096 bits) server-digest SHA256)
> 	(No client certificate requested)
> 	(Authenticated sender: cristicc)
> 	by bali.collaboradmins.com (Postfix) with ESMTPSA id AF4D717E0E67;
> 	Fri, 27 Feb 2026 21:48:51 +0100 (CET)
> From: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
> Subject: [PATCH 0/6] phy: rockchip: samsung-hdptx: Clock fixes and API
>   transition cleanups
> Date: Fri, 27 Feb 2026 22:48:44 +0200
> Message-Id: <20260227-hdptx-clk-fixes-v1-0-f998f2762d0f@collabora.com>
> MIME-Version: 1.0
> X-B4-Tracking: v=1; b=H4sIAAAAAAAC/x3LQQqAIBBA0avErBuoSTS6SrSIGmsoTDRCCO+et
>   Hx8/guRg3CEoXoh8CNRLlfQ1hUs++w2RlmLgRrSDZHBffV3wuU80EriiMoo0roj22uCcvnAfyj
>   TOOX8AXle+u9hAAAA
> X-Change-ID: 20260227-hdptx-clk-fixes-47426632f862
> To: Vinod Koul <vkoul@kernel.org>,
>   Neil Armstrong <neil.armstrong@linaro.org>,
>   Heiko Stuebner <heiko@sntech.de>, Algea Cao <algea.cao@rock-chips.com>,
>   Dmitry Baryshkov <lumag@kernel.org>
> Cc: kernel@collabora.com, linux-phy@lists.infradead.org,
>   linux-arm-kernel@lists.infradead.org, linux-rockchip@lists.infradead.org,
>   linux-kernel@vger.kernel.org
> X-Mailer: b4 0.14.3
> X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3
> X-CRM114-CacheID: sfid-20260227_124856_768935_57D7D58A
> X-CRM114-Status: UNSURE (   7.77  )
> X-CRM114-Notice: Please train this message.
> X-BeenThere: linux-rockchip@lists.infradead.org
> X-Mailman-Version: 2.1.34
> Precedence: list
> List-Id: Upstream kernel work for Rockchip platforms <linux-rockchip.lists.infradead.org>
> List-Unsubscribe: <http://lists.infradead.org/mailman/options/linux-rockchip>,
>   <mailto:linux-rockchip-request@lists.infradead.org?subject=unsubscribe>
> List-Archive: <http://lists.infradead.org/pipermail/linux-rockchip/>
> List-Post: <mailto:linux-rockchip@lists.infradead.org>
> List-Help: <mailto:linux-rockchip-request@lists.infradead.org?subject=help>
> List-Subscribe: <http://lists.infradead.org/mailman/listinfo/linux-rockchip>,
>   <mailto:linux-rockchip-request@lists.infradead.org?subject=subscribe>
> Content-Type: text/plain; charset="us-ascii"
> Content-Transfer-Encoding: 7bit
> Sender: "Linux-rockchip" <linux-rockchip-bounces@lists.infradead.org>
> Errors-To: linux-rockchip-bounces+linux-rockchip=archiver.kernel.org@lists.infradead.org
>
> This series provides a set of bug fixes and cleanups for the Rockchip
> Samsung HDPTX PHY driver.
>
> The first part of the series (i.e. PATCH 1 & 2) addresses clock rate
> calculation and synchronization issues.  Specifically, it fixes edge
> cases where the PHY PLL is pre-programmed by an external component (like
> a bootloader) or when changing the color depth (bpc) while keeping the
> modeline constant.  Because the Common Clock Framework .set_rate()
> callback might not be invoked if the pixel clock remains unchanged, this
> previously led to out-of-sync states between CCF and the actual HDMI PHY
> configuration.
>
> The second part focuses on code cleanups and modernizing the register
> access.  Now that dw_hdmi_qp driver has fully switched to using
> phy_configure(), we can drop the deprecated TMDS rate setup workarounds
> and the restrict_rate_change flag logic.  Finally, it refactors the
> driver to consistently use standard bitfield macros.
>
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
> ---
> Cristian Ciocaltea (6):
>        phy: rockchip: samsung-hdptx: Fix rate recalculation for high bpc
>        phy: rockchip: samsung-hdptx: Handle uncommitted PHY config changes
>        phy: rockchip: samsung-hdptx: Drop TMDS rate setup workaround
>        phy: rockchip: samsung-hdptx: Drop restrict_rate_change handling
>        phy: rockchip: samsung-hdptx: Simplify GRF access with FIELD_PREP_WM16()
>        phy: rockchip: samsung-hdptx: Consistently use bitfield macros
>
>   drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 215 +++++++++-------------
>   1 file changed, 92 insertions(+), 123 deletions(-)
> ---
> base-commit: 7d6661873f6b54c75195780a40d66bad3d482d8f
> change-id: 20260227-hdptx-clk-fixes-47426632f862
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
>  From mboxrd@z Thu Jan  1 00:00:00 1970
> Return-Path: <linux-phy-bounces+linux-phy=archiver.kernel.org@lists.infradead.org>
> X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on
> 	aws-us-west-2-korg-lkml-1.web.codeaurora.org
> Received: from bombadil.infradead.org (bombadil.infradead.org [198.137.202.133])
> 	(using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits))
> 	(No client certificate requested)
> 	by smtp.lore.kernel.org (Postfix) with ESMTPS id CB9D410398AD
> 	for <linux-phy@archiver.kernel.org>; Fri, 27 Feb 2026 20:48:59 +0000 (UTC)
> DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
> 	d=lists.infradead.org; s=bombadil.20210309; h=Sender:
> 	Content-Transfer-Encoding:Content-Type:List-Subscribe:List-Help:List-Post:
> 	List-Archive:List-Unsubscribe:List-Id:Cc:To:MIME-Version:Message-Id:Date:
> 	Subject:From:Reply-To:Content-ID:Content-Description:Resent-Date:Resent-From:
> 	Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID:In-Reply-To:References:
> 	List-Owner; bh=c324XN03PoA1rraJ+VV9Yfc0lnX3AkSpF9xHmfHI2Uc=; b=aTzKex1omAyuFL
> 	6ssxrkQBX8aNauOphSMRtLUHi7gaYYX8hBEmLsN3BQpo2//ODwY72uHzTo0s682gBT+6OQK42ltgf
> 	7rkCcxaIcVIuYIOMyD0cwGdVTVB4zXapp6g9uTVDlwKBJmJeTRWJFJFTPr0X4L5E2tzoZ+3H3yNzR
> 	kJqpmj9lVVE5UDflVckhQhImOTJdXGyqxptH+Yz2qZijDxp554oddwvnOAii/xKkAQv4nwS23h/5R
> 	CrPiaPT3d0/Z2mtZbkl7rqYarf3D+Qg+Pei5yOAuVw3DTlocsu9nEpM3+biDUT7yO2T0N5c4Lq8yy
> 	BNVFkTqRDzWU+QPFJM6A==;
> Received: from localhost ([::1] helo=bombadil.infradead.org)
> 	by bombadil.infradead.org with esmtp (Exim 4.98.2 #2 (Red Hat Linux))
> 	id 1vw4lf-000000098bn-1y20;
> 	Fri, 27 Feb 2026 20:48:59 +0000
> Received: from bali.collaboradmins.com ([2a01:4f8:201:9162::2])
> 	by bombadil.infradead.org with esmtps (Exim 4.98.2 #2 (Red Hat Linux))
> 	id 1vw4lc-000000098ZS-2DwJ;
> 	Fri, 27 Feb 2026 20:48:57 +0000
> DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/simple; d=collabora.com;
> 	s=mail; t=1772225331;
> 	bh=bUeULh1bnVKovxRmlxehE6KS7aqNBCqPFyvaWOEsoaE=;
> 	h=From:Subject:Date:To:Cc:From;
> 	b=ekEaWw1uHuEz0iWpTlf7zG60N1dzqsUimUI0n7bx/xvqftKi5TS1D3FCMNmggdH15
> 	 nip240uzI3bC+sOV8/OHY8BKzO+U3KESiaX+LJuDTU5hdz/nyF19JOtVbOpEUwy2H2
> 	 nFG6mRz4JB6hSMOKVCGAxx27/gF8KCMaI21JIexzBmepPZApw6kf+9mFzcd2NqJPpe
> 	 kLTjON2UczI2jLr009ZWvx9fb2AVXa6s6axkOohMwRy+ggic0yZzQ7Pxjjdm6IZqcQ
> 	 ZtkEM8UHO29BkkEAX61miqbj6HTB7BAWlet6Q1SF2oqLc452ZSEViEuj67tw8dzuBz
> 	 E7iPV6xRgfL3g==
> Received: from localhost (unknown [86.123.23.225])
> 	(using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits)
> 	 key-exchange ECDHE (prime256v1) server-signature RSA-PSS (4096 bits) server-digest SHA256)
> 	(No client certificate requested)
> 	(Authenticated sender: cristicc)
> 	by bali.collaboradmins.com (Postfix) with ESMTPSA id AF4D717E0E67;
> 	Fri, 27 Feb 2026 21:48:51 +0100 (CET)
> From: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
> Subject: [PATCH 0/6] phy: rockchip: samsung-hdptx: Clock fixes and API
>   transition cleanups
> Date: Fri, 27 Feb 2026 22:48:44 +0200
> Message-Id: <20260227-hdptx-clk-fixes-v1-0-f998f2762d0f@collabora.com>
> MIME-Version: 1.0
> X-B4-Tracking: v=1; b=H4sIAAAAAAAC/x3LQQqAIBBA0avErBuoSTS6SrSIGmsoTDRCCO+et
>   Hx8/guRg3CEoXoh8CNRLlfQ1hUs++w2RlmLgRrSDZHBffV3wuU80EriiMoo0roj22uCcvnAfyj
>   TOOX8AXle+u9hAAAA
> X-Change-ID: 20260227-hdptx-clk-fixes-47426632f862
> To: Vinod Koul <vkoul@kernel.org>,
>   Neil Armstrong <neil.armstrong@linaro.org>,
>   Heiko Stuebner <heiko@sntech.de>, Algea Cao <algea.cao@rock-chips.com>,
>   Dmitry Baryshkov <lumag@kernel.org>
> Cc: kernel@collabora.com, linux-phy@lists.infradead.org,
>   linux-arm-kernel@lists.infradead.org, linux-rockchip@lists.infradead.org,
>   linux-kernel@vger.kernel.org
> X-Mailer: b4 0.14.3
> X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3
> X-CRM114-CacheID: sfid-20260227_124856_768935_57D7D58A
> X-CRM114-Status: UNSURE (   7.77  )
> X-CRM114-Notice: Please train this message.
> X-BeenThere: linux-phy@lists.infradead.org
> X-Mailman-Version: 2.1.34
> Precedence: list
> List-Id: Linux Phy Mailing list <linux-phy.lists.infradead.org>
> List-Unsubscribe: <https://lists.infradead.org/mailman/options/linux-phy>,
>   <mailto:linux-phy-request@lists.infradead.org?subject=unsubscribe>
> List-Archive: <http://lists.infradead.org/pipermail/linux-phy/>
> List-Post: <mailto:linux-phy@lists.infradead.org>
> List-Help: <mailto:linux-phy-request@lists.infradead.org?subject=help>
> List-Subscribe: <https://lists.infradead.org/mailman/listinfo/linux-phy>,
>   <mailto:linux-phy-request@lists.infradead.org?subject=subscribe>
> Content-Type: text/plain; charset="us-ascii"
> Content-Transfer-Encoding: 7bit
> Sender: "linux-phy" <linux-phy-bounces@lists.infradead.org>
> Errors-To: linux-phy-bounces+linux-phy=archiver.kernel.org@lists.infradead.org
>
> This series provides a set of bug fixes and cleanups for the Rockchip
> Samsung HDPTX PHY driver.
>
> The first part of the series (i.e. PATCH 1 & 2) addresses clock rate
> calculation and synchronization issues.  Specifically, it fixes edge
> cases where the PHY PLL is pre-programmed by an external component (like
> a bootloader) or when changing the color depth (bpc) while keeping the
> modeline constant.  Because the Common Clock Framework .set_rate()
> callback might not be invoked if the pixel clock remains unchanged, this
> previously led to out-of-sync states between CCF and the actual HDMI PHY
> configuration.
>
> The second part focuses on code cleanups and modernizing the register
> access.  Now that dw_hdmi_qp driver has fully switched to using
> phy_configure(), we can drop the deprecated TMDS rate setup workarounds
> and the restrict_rate_change flag logic.  Finally, it refactors the
> driver to consistently use standard bitfield macros.
>
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
> ---
> Cristian Ciocaltea (6):
>        phy: rockchip: samsung-hdptx: Fix rate recalculation for high bpc
>        phy: rockchip: samsung-hdptx: Handle uncommitted PHY config changes
>        phy: rockchip: samsung-hdptx: Drop TMDS rate setup workaround
>        phy: rockchip: samsung-hdptx: Drop restrict_rate_change handling
>        phy: rockchip: samsung-hdptx: Simplify GRF access with FIELD_PREP_WM16()
>        phy: rockchip: samsung-hdptx: Consistently use bitfield macros
>
>   drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 215 +++++++++-------------
>   1 file changed, 92 insertions(+), 123 deletions(-)
> ---
> base-commit: 7d6661873f6b54c75195780a40d66bad3d482d8f
> change-id: 20260227-hdptx-clk-fixes-47426632f862
>
>

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH 0/6] phy: rockchip: samsung-hdptx: Clock fixes and API transition cleanups

[Vinod Koul]

On 27-02-26, 22:48, Cristian Ciocaltea wrote:
> This series provides a set of bug fixes and cleanups for the Rockchip
> Samsung HDPTX PHY driver.
> 
> The first part of the series (i.e. PATCH 1 & 2) addresses clock rate
> calculation and synchronization issues.  Specifically, it fixes edge
> cases where the PHY PLL is pre-programmed by an external component (like
> a bootloader) or when changing the color depth (bpc) while keeping the
> modeline constant.  Because the Common Clock Framework .set_rate()
> callback might not be invoked if the pixel clock remains unchanged, this
> previously led to out-of-sync states between CCF and the actual HDMI PHY
> configuration.
> 
> The second part focuses on code cleanups and modernizing the register
> access.  Now that dw_hdmi_qp driver has fully switched to using
> phy_configure(), we can drop the deprecated TMDS rate setup workarounds
> and the restrict_rate_change flag logic.  Finally, it refactors the
> driver to consistently use standard bitfield macros.

Sorry looks like I have missed to review this one.
Can you please rebase on phy/fixes and send...

Thanks
-- 
~Vinod

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH 0/6] phy: rockchip: samsung-hdptx: Clock fixes and API transition cleanups

[Cristian Ciocaltea]

Hi Vinod,

On 5/10/26 10:36 AM, Vinod Koul wrote:
> On 27-02-26, 22:48, Cristian Ciocaltea wrote:
>> This series provides a set of bug fixes and cleanups for the Rockchip
>> Samsung HDPTX PHY driver.
>>
>> The first part of the series (i.e. PATCH 1 & 2) addresses clock rate
>> calculation and synchronization issues.  Specifically, it fixes edge
>> cases where the PHY PLL is pre-programmed by an external component (like
>> a bootloader) or when changing the color depth (bpc) while keeping the
>> modeline constant.  Because the Common Clock Framework .set_rate()
>> callback might not be invoked if the pixel clock remains unchanged, this
>> previously led to out-of-sync states between CCF and the actual HDMI PHY
>> configuration.
>>
>> The second part focuses on code cleanups and modernizing the register
>> access.  Now that dw_hdmi_qp driver has fully switched to using
>> phy_configure(), we can drop the deprecated TMDS rate setup workarounds
>> and the restrict_rate_change flag logic.  Finally, it refactors the
>> driver to consistently use standard bitfield macros.
> 
> Sorry looks like I have missed to review this one.
> Can you please rebase on phy/fixes and send...

I've just verified and it applies cleanly on top of phy/fixes.
Do you still need a resend?

Regards,
Cristian

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip