* Re: [PATCH] ptp: ocp: don't allow on S390
2021-08-20 8:02 ` [PATCH] ptp: ocp: don't allow on S390 Christian Borntraeger
@ 2021-08-20 9:59 ` Niklas Schnelle
0 siblings, 0 replies; 2+ messages in thread
From: Niklas Schnelle @ 2021-08-20 9:59 UTC (permalink / raw)
To: Christian Borntraeger, Randy Dunlap, Jonathan Lemon,
Hendrik Brueckner, linux-s390
Cc: netdev, Richard Cochran, Greg KH
On Fri, 2021-08-20 at 10:02 +0200, Christian Borntraeger wrote:
>
> On 20.08.21 00:58, Randy Dunlap wrote:
> > On 8/16/21 2:41 PM, Jonathan Lemon wrote:
> > > On Mon, Aug 16, 2021 at 02:15:51PM -0700, Randy Dunlap wrote:
> > > > On 8/16/21 2:09 PM, Jonathan Lemon wrote:
> > > > > On Fri, Aug 13, 2021 at 01:30:26PM -0700, Randy Dunlap wrote:
> > > > > > There is no 8250 serial on S390. See commit 1598e38c0770.
> > > > >
> > > > > There's a 8250 serial device on the PCI card. Its been
> > > > > ages since I've worked on the architecture, but does S390
> > > > > even support PCI?
> > > >
> > > > Yes, it does.
>
> We do support PCI, but only a (very) limited amount of cards.
> So there never will be a PCI card with 8250 on s390 and
> I also doubt that we will see the "OpenCompute TimeCard"
> on s390.
>
> So in essence the original patch is ok but the patch below
> would also be ok for KVM. But it results in a larger kernel
> with code that will never be used. So I guess the original
> patch is the better choice.
It looks to me like the SERIAL_8250 driver can be build as a module so
would then not increase the kernel image size or am I missing
something?
In that case I would vote for the patch below. For PCI on s390 we do
intend to, in principle, support arbitrary PCI devices and have already
seen cases where non-trivial cards that were never before tested on
s390 did "just work" once someone needed them.
While I do agree that both 8250 and the Time Card are unlikely to be
used on s390 never say never and compile testing a variety of driver
code against our PCI primitives is good for quality control.
In the end I'm okay with either.
>
> > > > > > Is this driver useful even without 8250 serial?
> > > > >
> > > > > The FB timecard has an FPGA that will internally parse the
> > > > > GNSS strings and correct the clock, so the PTP clock will
> > > > > work even without the serial devices.
> > > > >
> > > > > However, there are userspace tools which want to read the
> > > > > GNSS signal (for holdolver and leap second indication),
> > > > > which is why they are exposed.
> > > >
> > > > So what do you recommend here?
> > >
> > > Looking at 1598e38c0770, it appears the 8250 console is the
> > > problem. Couldn't S390 be fenced by SERIAL_8250_CONSOLE, instead
> > > of SERIAL_8250, which would make the 8250 driver available?
> >
> > OK, that sounds somewhat reasonable.
> >
> > > For now, just disabling the driver on S390 sounds reasonable.
> > >
> >
> > S390 people, how does this look to you?
> >
> > This still avoids having serial 8250 console conflicting
> > with S390's sclp console.
> > (reference commit 1598e38c0770)
> >
> >
> > ---
> > drivers/tty/serial/8250/Kconfig | 2 +-
> > 1 file changed, 1 insertion(+), 1 deletion(-)
> >
> > --- linux-next-20210819.orig/drivers/tty/serial/8250/Kconfig
> > +++ linux-next-20210819/drivers/tty/serial/8250/Kconfig
> > @@ -6,7 +6,6 @@
> >
> > config SERIAL_8250
> > tristate "8250/16550 and compatible serial support"
> > - depends on !S390
> > select SERIAL_CORE
> > select SERIAL_MCTRL_GPIO if GPIOLIB
> > help
> > @@ -85,6 +84,7 @@ config SERIAL_8250_FINTEK
> > config SERIAL_8250_CONSOLE
> > bool "Console on 8250/16550 and compatible serial port"
> > depends on SERIAL_8250=y
> > + depends on !S390
> > select SERIAL_CORE_CONSOLE
> > select SERIAL_EARLYCON
> > help
> >
> >
^ permalink raw reply [flat|nested] 2+ messages in thread