Symmetric Multiprocessing (SMP) development
 help / color / mirror / Atom feed
* No IRQ assigned to my PCI nic, on an ASUS A7M266D w two AMD 2000s
@ 2002-08-17  0:54 Mark Wigzell
  2002-08-17 19:18 ` Alan Cox
  0 siblings, 1 reply; 2+ messages in thread
From: Mark Wigzell @ 2002-08-17  0:54 UTC (permalink / raw)
  To: linux-smp

Hi, I'm having trouble getting the APIC to assign an IRQ to my NIC. 
BIOS is AWARD 1006.

Is there a fix for this?

Mark

+ cat /proc/pci
PCI devices found:
  Bus  0, device   0, function  0:
    Host bridge: PCI device 1022:700c (Advanced Micro Devices [AMD]) (rev 17).
      Master Capable.  Latency=32.  
      Prefetchable 32 bit memory at 0xf8000000 [0xfbffffff].
      Prefetchable 32 bit memory at 0xf7800000 [0xf7800fff].
      I/O at 0xe800 [0xe803].
  Bus  0, device   1, function  0:
    PCI bridge: PCI device 1022:700d (Advanced Micro Devices [AMD]) (rev 0).
      Master Capable.  No bursts.  Min Gnt=8.
  Bus  0, device   7, function  0:
    ISA bridge: PCI device 1022:7440 (Advanced Micro Devices [AMD]) (rev 5).
  Bus  0, device   7, function  1:
    IDE interface: PCI device 1022:7441 (Advanced Micro Devices [AMD]) (rev 4).
      Master Capable.  Latency=32.  
      I/O at 0xd800 [0xd80f].
  Bus  0, device   7, function  3:
    Bridge: PCI device 1022:7443 (Advanced Micro Devices [AMD]) (rev 3).
      Master Capable.  Latency=32.  
  Bus  0, device  16, function  0:
    PCI bridge: PCI device 1022:7448 (Advanced Micro Devices [AMD]) (rev 5).
      Master Capable.  Latency=32.  Min Gnt=4.
  Bus  1, device   5, function  0:
    VGA compatible controller: PCI device 10de:0253 (nVidia Corporation) (rev 162).
      IRQ 16.
      Master Capable.  Latency=64.  Min Gnt=5.Max Lat=1.
      Non-prefetchable 32 bit memory at 0xe6000000 [0xe6ffffff].
      Prefetchable 32 bit memory at 0xe8000000 [0xefffffff].
      Prefetchable 32 bit memory at 0xe7800000 [0xe787ffff].
  Bus  2, device   0, function  0:
    USB Controller: PCI device 1022:7449 (Advanced Micro Devices [AMD]) (rev 7).
      IRQ 19.
      Master Capable.  Latency=32.  Max Lat=80.
      Non-prefetchable 32 bit memory at 0xe5800000 [0xe5800fff].
  Bus  2, device   4, function  0:
    Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 16).
      Master Capable.  Latency=32.  Min Gnt=2.Max Lat=24.
      I/O at 0xc800 [0xc8ff].
  Bus  2, device   5, function  0:
    USB Controller: NEC Corporation USB (rev 65).
      IRQ 18.
      Master Capable.  Latency=32.  Min Gnt=1.Max Lat=42.
      Non-prefetchable 32 bit memory at 0xe5000000 [0xe5000fff].
  Bus  2, device   5, function  1:
    USB Controller: NEC Corporation USB (#2) (rev 65).
      IRQ 19.
      Master Capable.  Latency=32.  Min Gnt=1.Max Lat=42.
      Non-prefetchable 32 bit memory at 0xe4800000 [0xe4800fff].
  Bus  2, device   5, function  2:
    USB Controller: PCI device 1033:00e0 (NEC Corporation) (rev 2).
      IRQ 16.
      Master Capable.  Latency=32.  Min Gnt=16.Max Lat=34.
      Non-prefetchable 32 bit memory at 0xe4000000 [0xe40000ff].
  Bus  2, device   8, function  0:
    Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 120).
      Master Capable.  Latency=32.  Min Gnt=10.Max Lat=10.
      I/O at 0xc400 [0xc47f].
      Non-prefetchable 32 bit memory at 0xe3800000 [0xe380007f].
+ cat /proc/interrupts
           CPU0       CPU1       
  0:      16847      16976    IO-APIC-edge  timer
  1:        384        179    IO-APIC-edge  keyboard
  2:          0          0          XT-PIC  cascade
  8:          1          0    IO-APIC-edge  rtc
 14:       1673       3235    IO-APIC-edge  ide0
 15:          2          2    IO-APIC-edge  ide1
 18:          0          0   IO-APIC-level  usb-ohci
 19:          0          0   IO-APIC-level  usb-ohci, usb-ohci
NMI:          0          0 
LOC:      33746      33745 
ERR:          0
MIS:          0
+ dmesg
Linux version 2.4.7-10smp (bhcompile@stripples.devel.redhat.com) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-98)) #1 SMP Thu Sep 6 16:16:16 EDT 2001
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ffec000 (usable)
 BIOS-e820: 000000003ffec000 - 000000003ffef000 (ACPI data)
 BIOS-e820: 000000003ffef000 - 000000003ffff000 (reserved)
 BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
found SMP MP-table at 000f7d40
hm, page 000f7000 reserved twice.
hm, page 000f8000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 000f8000 reserved twice.
On node 0 totalpages: 262124
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32748 pages.
Intel MultiProcessor Specification v1.4
    Virtual Wire compatibility mode.
OEM ID: ASUS     Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 16
Processor #1 Pentium(tm) Pro APIC version 16
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
Kernel command line: ro root=/dev/hdb3 hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1666.767 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3322.67 BogoMIPS
Memory: 1026824k/1048496k available (1389k kernel code, 20264k reserved, 108k data, 240k init, 130992k highmem)
Dentry-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 9, 2097152 bytes)
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:     After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:             Common caps: 0383fbff c1cbfbff 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
Intel machine check reporting enabled on CPU#0.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:     After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:             Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU0: AMD Athlon(TM) MP 2000+ stepping 02
per-CPU timeslice cutoff: 731.44 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 3329.22 BogoMIPS
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
Intel machine check reporting enabled on CPU#1.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:     After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:             Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU1: AMD Athlon(TM) MP 2000+ stepping 02
Total of 2 processors activated (6651.90 BogoMIPS).
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-3, 2-5, 2-10, 2-11, 2-17, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 17.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.... register #01: 00170011
.......     : max redirection entries: 0017
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 000 00  1    0    0   0   0    0    0    00
 01 003 03  0    0    0   0   0    1    1    39
 02 003 03  0    0    0   0   0    1    1    31
 03 000 00  1    0    0   0   0    0    0    00
 04 003 03  0    0    0   0   0    1    1    41
 05 000 00  1    0    0   0   0    0    0    00
 06 003 03  0    0    0   0   0    1    1    49
 07 003 03  0    0    0   0   0    1    1    51
 08 003 03  0    0    0   0   0    1    1    59
 09 003 03  0    0    0   0   0    1    1    61
 0a 000 00  1    0    0   0   0    0    0    00
 0b 000 00  1    0    0   0   0    0    0    00
 0c 003 03  0    0    0   0   0    1    1    69
 0d 003 03  0    0    0   0   0    1    1    71
 0e 003 03  0    0    0   0   0    1    1    79
 0f 003 03  0    0    0   0   0    1    1    81
 10 003 03  1    1    0   1   0    1    1    89
 11 000 00  1    0    0   0   0    0    0    00
 12 003 03  1    1    0   1   0    1    1    91
 13 003 03  1    1    0   1   0    1    1    99
 14 000 00  1    0    0   0   0    0    0    00
 15 000 00  1    0    0   0   0    0    0    00
 16 000 00  1    0    0   0   0    0    0    00
 17 000 00  1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1666.6465 MHz.
..... host bus clock speed is 266.6632 MHz.
cpu: 0, clocks: 2666632, slice: 888877
CPU0<T0:2666624,T1:1777744,D:3,S:888877,C:2666632>
cpu: 1, clocks: 2666632, slice: 888877
CPU1<T0:2666624,T1:888864,D:6,S:888877,C:2666632>
checking TSC synchronization across CPUs: passed.
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xf1dd0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router default [1022/7443] at 00:07.3
PCI->APIC IRQ transform: (B1,I5,P0) -> 16
PCI->APIC IRQ transform: (B2,I0,P3) -> 19
PCI->APIC IRQ transform: (B2,I5,P0) -> 18
PCI->APIC IRQ transform: (B2,I5,P1) -> 19
PCI->APIC IRQ transform: (B2,I5,P2) -> 16
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Simple Boot Flag extension found and enabled.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
apm: disabled - APM is not SMP safe.
Starting kswapd v1.8
allocated 64 pages and 64 bhs reserved for the highmem bounces
VFS: Diskquotas version dquot_6.5.0 initialized
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10d
block: queued sectors max/low 681549kB/550477kB, 2048 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx
PCI_IDE: unknown IDE controller on PCI bus 00 device 39, VID=1022, DID=7441
PCI_IDE: chipset revision 4
PCI_IDE: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
hda: ST380021A, ATA DISK drive
hdb: ST380021A, ATA DISK drive
hdc: PLEXTOR CD-R PX-W4012A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(33)
hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(33)
ide-floppy driver 0.97
Partition check:
 hda: hda1
 hdb: hdb1 hdb2 hdb3
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ide-floppy driver 0.97
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 324k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 240k freed
Adding Swap: 2040244k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xf892e000, IRQ 19
usb-ohci.c: usb-02:00.0, PCI device 1022:7449 (Advanced Micro Devices [AMD])
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 4 ports detected
usb-ohci.c: USB OHCI at membase 0xf8930000, IRQ 18
usb-ohci.c: usb-02:05.0, NEC Corporation USB
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xf8932000, IRQ 19
usb-ohci.c: usb-02:05.1, NEC Corporation USB (#2)
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-ohci.c: v5.2:USB OHCI Host Controller Driver
EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,67), internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,65), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SCSI subsystem driver Revision: 1.00
Disallowing DMA for hdc 
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
  Vendor: PLEXTOR   Model: CD-R   PX-W4012A  Rev: 1.01
  Type:   CD-ROM                             ANSI SCSI revision: 02

>>>>> This is where I ran "insmod 3c59x":

PCI: Enabling device 02:08.0 (0014 -> 0017)
PCI: No IRQ known for interrupt pin A of device 02:08.0. Probably buggy MP table.
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
02:08.0: 3Com PCI 3c905C Tornado at 0xc400. Vers LK1.1.16
 *** Warning: IRQ 0 is unlikely to work! ***


^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2002-08-17 19:18 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2002-08-17  0:54 No IRQ assigned to my PCI nic, on an ASUS A7M266D w two AMD 2000s Mark Wigzell
2002-08-17 19:18 ` Alan Cox

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox