* [PATCH v3] USB: hub: call ACPI _PRR reset during port power-cycle on enumeration failure
@ 2026-11-03 6:08 Mario Limonciello
2026-11-03 6:18 ` sashiko-bot
2026-11-19 14:58 ` Mario Limonciello
0 siblings, 2 replies; 4+ messages in thread
From: Mario Limonciello @ 2026-11-03 6:08 UTC (permalink / raw)
To: Greg Kroah-Hartman
Cc: linux-usb, linux-kernel, Rafael J. Wysocki, Mika Westerberg,
linux-acpi, Chia-Lin Kao (AceLan), Mario Limonciello (AMD)
Some USB-connected devices (e.g. MT7925 Bluetooth on Dell laptops) expose
their hardware reset line via an ACPI Power Resource for Reset (_PRR)
rather than relying solely on VBUS cycling for recovery. When the reset
GPIO gets stuck low the device stops responding on USB; a VBUS power-cycle
alone cannot recover it because the chip remains in reset regardless of
VBUS state.
Add usb_acpi_port_prr_reset() in usb-acpi.c that, given a hub device and
one-based port number, looks up the port's ACPI companion handle, evaluates
_PRR to obtain the power-resource reference, and then calls _RST on that
reference to toggle the reset line. The function is a no-op if the port
has no ACPI handle or no _PRR method, so it is safe to call unconditionally
for every port.
Wire it into hub_port_connect() during the mid-retry VBUS power-cycle
(at (PORT_INIT_TRIES-1)/2 iterations), calling usb_acpi_port_prr_reset()
*after* VBUS goes off and *before* VBUS comes back on. The ordering is
critical: on the tested hardware the ACPI _RST method (MBTR._RST) drives
BT_RST low for 200 ms then high again. If _RST is called after VBUS is
already restored the GPIO pulse races with device enumeration starting on
the live bus; the device begins asserting USB signals while still held in
reset and enumeration fails. Performing the reset while the port is
de-powered ensures the GPIO pulse completes fully before the device is
given power and time to initialise.
After VBUS is restored, add an msleep(100) conditional on _PRR._RST having
succeeded. USB 2.0 spec §7.1.7.3 (Fig. 7-29) mandates a minimum of 100 ms
between VBUS power-on and the first reset signalling for power settling.
On root hubs, hub_power_on_good_delay() returns bPwrOn2PwrGood * 2 with
no minimum floor; on the tested xHCI root hub bPwrOn2PwrGood = 10, yielding
only 20 ms — well below the spec minimum. (External hubs already enforce
a 100 ms minimum via hub_power_on_good_delay().) When _PRR._RST has been
exercised the device must also complete its full power-on sequence (GPIO
de-assertion, internal oscillator start, firmware load) before USB
enumeration begins. The 100 ms sleep enforces the spec minimum and gives
the device adequate settling time.
Tested on a Dell laptop with MT7925 Bluetooth (idVendor=0489,
idProduct=e139) whose BT_RST GPIO was stuck low. With this fix the
device recovers autonomously at boot without requiring a G3
(mechanical power-off) cycle. The relevant dmesg sequence:
[ 1.448491] usb 3-10: new high-speed USB device number 4 using xhci_hcd
[ 6.813942] usb 3-10: device descriptor read/64, error -110
[ 22.685978] usb 3-10: device descriptor read/64, error -110
[ 22.901715] usb 3-10: new high-speed USB device number 5 using xhci_hcd
[ 28.317963] usb 3-10: device descriptor read/64, error -110
[ 44.189949] usb 3-10: device descriptor read/64, error -110
[ 44.294065] usb usb3-port10: attempt power cycle
[ 44.872709] usb 3-10: new high-speed USB device number 6 using xhci_hcd
[ 44.888293] usb 3-10: New USB device found, idVendor=0489, idProduct=e139, bcdDevice= 1.00
[ 44.888318] usb 3-10: Manufacturer: MediaTek Inc.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20260706080117.3754550-1-acelan.kao@canonical.com
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
---
This was sent last cycle but got no feedback except for my review comment.
I think we should bring it forward this cycle.
Changes from v2:
* Rebase on 7.4-rc1
* Link to v2: https://lore.kernel.org/linux-usb/20260706080117.3754550-1-acelan.kao@canonical.com/
---
drivers/usb/core/hub.c | 14 ++++++++++
drivers/usb/core/usb-acpi.c | 68 +++++++++++++++++++++++++++++++++++++++++++++
drivers/usb/core/usb.h | 3 ++
3 files changed, 85 insertions(+)
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 199d3f535a891..72da7aea94cc4 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -5621,11 +5621,25 @@ static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus,
/* When halfway through our retry count, power-cycle the port */
if (i == (PORT_INIT_TRIES - 1) / 2) {
+ int prr_reset;
+
dev_info(&port_dev->dev, "attempt power cycle\n");
usb_hub_set_port_power(hdev, hub, port1, false);
msleep(2 * hub_power_on_good_delay(hub));
+ prr_reset = usb_acpi_port_prr_reset(hdev, port1);
usb_hub_set_port_power(hdev, hub, port1, true);
msleep(hub_power_on_good_delay(hub));
+ /*
+ * USB 2.0 spec §7.1.7.3 requires at least 100 ms
+ * between VBUS power-on and the first reset for power
+ * settling. hub_power_on_good_delay() on an xHCI root
+ * hub returns bPwrOn2PwrGood * 2 with no minimum floor,
+ * which can be as little as 20 ms. When _PRR _RST was
+ * also exercised the device must complete its power-on
+ * sequence before enumeration; enforce the spec minimum.
+ */
+ if (prr_reset == 0)
+ msleep(100);
}
}
if (hub->hdev->parent ||
diff --git a/drivers/usb/core/usb-acpi.c b/drivers/usb/core/usb-acpi.c
index 489dbdc96f94a..bb1b5e8cdc15e 100644
--- a/drivers/usb/core/usb-acpi.c
+++ b/drivers/usb/core/usb-acpi.c
@@ -142,6 +142,74 @@ int usb_acpi_set_power_state(struct usb_device *hdev, int index, bool enable)
}
EXPORT_SYMBOL_GPL(usb_acpi_set_power_state);
+/**
+ * usb_acpi_port_prr_reset - issue an ACPI _PRR reset on a hub port
+ * @hdev: USB device belonging to the usb hub
+ * @port1: port number (one-based)
+ *
+ * Some devices expose their hardware reset line via an ACPI Power Resource for
+ * Reset (_PRR). When such a device fails to enumerate (e.g. because the reset
+ * GPIO is stuck low), the USB power-cycle alone is not enough; the firmware
+ * reset path must also be exercised.
+ *
+ * This function evaluates _PRR on the port's ACPI companion to obtain the
+ * power-resource reference and then calls _RST on that resource to toggle the
+ * reset line. It is intended to be called alongside the mid-retry VBUS
+ * power-cycle already performed by hub_port_connect().
+ *
+ * Returns 0 on success, -ENODEV if the port has no ACPI handle or no _PRR
+ * method, or a negative error code on failure.
+ */
+int usb_acpi_port_prr_reset(struct usb_device *hdev, int port1)
+{
+ acpi_handle port_handle;
+ struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+ union acpi_object *pkg, *ref;
+ acpi_status status;
+ int ret = 0;
+
+ port_handle = usb_get_hub_port_acpi_handle(hdev, port1);
+ if (!port_handle)
+ return -ENODEV;
+
+ if (!acpi_has_method(port_handle, "_PRR"))
+ return -ENODEV;
+
+ status = acpi_evaluate_object(port_handle, "_PRR", NULL, &buffer);
+ if (ACPI_FAILURE(status)) {
+ dev_dbg(&hdev->dev, "port%d: _PRR evaluation failed: %s\n",
+ port1, acpi_format_exception(status));
+ return -ENODEV;
+ }
+
+ pkg = buffer.pointer;
+ if (!pkg || pkg->type != ACPI_TYPE_PACKAGE || pkg->package.count != 1) {
+ dev_dbg(&hdev->dev, "port%d: _PRR returned unexpected object\n",
+ port1);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ ref = &pkg->package.elements[0];
+ if (ref->type != ACPI_TYPE_LOCAL_REFERENCE || !ref->reference.handle) {
+ dev_dbg(&hdev->dev, "port%d: _PRR element is not a reference\n",
+ port1);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ status = acpi_evaluate_object(ref->reference.handle, "_RST", NULL, NULL);
+ if (ACPI_FAILURE(status)) {
+ dev_dbg(&hdev->dev, "port%d: _RST evaluation failed: %s\n",
+ port1, acpi_format_exception(status));
+ ret = -EIO;
+ }
+
+out:
+ kfree(buffer.pointer);
+ return ret;
+}
+
/**
* usb_acpi_add_usb4_devlink - add device link to USB4 Host Interface for tunneled USB3 devices
*
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index a9b37aeb515be..4d3dc3bd881b2 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -211,7 +211,10 @@ extern int usb_acpi_register(void);
extern void usb_acpi_unregister(void);
extern acpi_handle usb_get_hub_port_acpi_handle(struct usb_device *hdev,
int port1);
+extern int usb_acpi_port_prr_reset(struct usb_device *hdev, int port1);
#else
static inline int usb_acpi_register(void) { return 0; };
static inline void usb_acpi_unregister(void) { };
+static inline int usb_acpi_port_prr_reset(struct usb_device *hdev,
+ int port1) { return -ENODEV; }
#endif
---
base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4
change-id: 20260706080117.3754550-1-acelan.kao@canonical.com
Best regards,
--
Mario Limonciello <superm1@kernel.org>
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH v3] USB: hub: call ACPI _PRR reset during port power-cycle on enumeration failure
2026-11-03 6:08 [PATCH v3] USB: hub: call ACPI _PRR reset during port power-cycle on enumeration failure Mario Limonciello
@ 2026-11-03 6:18 ` sashiko-bot
2026-11-19 14:58 ` Mario Limonciello
1 sibling, 0 replies; 4+ messages in thread
From: sashiko-bot @ 2026-11-03 6:18 UTC (permalink / raw)
To: Mario Limonciello; +Cc: linux-usb
> Some USB-connected devices (e.g. MT7925 Bluetooth on Dell laptops) expose
> their hardware reset line via an ACPI Power Resource for Reset (_PRR)
> rather than relying solely on VBUS cycling for recovery. When the reset
> GPIO gets stuck low the device stops responding on USB; a VBUS power-cycle
> alone cannot recover it because the chip remains in reset regardless of
> VBUS state.
>
> Add usb_acpi_port_prr_reset() in usb-acpi.c that, given a hub device and
> one-based port number, looks up the port's ACPI companion handle, evaluates
> _PRR to obtain the power-resource reference, and then calls _RST on that
> reference to toggle the reset line. The function is a no-op if the port
> has no ACPI handle or no _PRR method, so it is safe to call unconditionally
> for every port.
>
> Wire it into hub_port_connect() during the mid-retry VBUS power-cycle
> [ ... ]
>
> Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
> Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
> Link: https://patch.msgid.link/20260706080117.3754550-1-acelan.kao@canonical.com
> Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Sashiko has reviewed this patch and found no issues.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20260706080117.3754550-1-v3-1-0e3069228fe9@kernel.org?part=1
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH v3] USB: hub: call ACPI _PRR reset during port power-cycle on enumeration failure
2026-11-03 6:08 [PATCH v3] USB: hub: call ACPI _PRR reset during port power-cycle on enumeration failure Mario Limonciello
2026-11-03 6:18 ` sashiko-bot
@ 2026-11-19 14:58 ` Mario Limonciello
2026-11-19 15:10 ` Greg Kroah-Hartman
1 sibling, 1 reply; 4+ messages in thread
From: Mario Limonciello @ 2026-11-19 14:58 UTC (permalink / raw)
To: Greg Kroah-Hartman
Cc: linux-usb, linux-kernel, Rafael J. Wysocki, Mika Westerberg,
linux-acpi, Chia-Lin Kao (AceLan)
On 11/3/26 00:08, Mario Limonciello wrote:
> Some USB-connected devices (e.g. MT7925 Bluetooth on Dell laptops) expose
> their hardware reset line via an ACPI Power Resource for Reset (_PRR)
> rather than relying solely on VBUS cycling for recovery. When the reset
> GPIO gets stuck low the device stops responding on USB; a VBUS power-cycle
> alone cannot recover it because the chip remains in reset regardless of
> VBUS state.
>
> Add usb_acpi_port_prr_reset() in usb-acpi.c that, given a hub device and
> one-based port number, looks up the port's ACPI companion handle, evaluates
> _PRR to obtain the power-resource reference, and then calls _RST on that
> reference to toggle the reset line. The function is a no-op if the port
> has no ACPI handle or no _PRR method, so it is safe to call unconditionally
> for every port.
>
> Wire it into hub_port_connect() during the mid-retry VBUS power-cycle
> (at (PORT_INIT_TRIES-1)/2 iterations), calling usb_acpi_port_prr_reset()
> *after* VBUS goes off and *before* VBUS comes back on. The ordering is
> critical: on the tested hardware the ACPI _RST method (MBTR._RST) drives
> BT_RST low for 200 ms then high again. If _RST is called after VBUS is
> already restored the GPIO pulse races with device enumeration starting on
> the live bus; the device begins asserting USB signals while still held in
> reset and enumeration fails. Performing the reset while the port is
> de-powered ensures the GPIO pulse completes fully before the device is
> given power and time to initialise.
>
> After VBUS is restored, add an msleep(100) conditional on _PRR._RST having
> succeeded. USB 2.0 spec §7.1.7.3 (Fig. 7-29) mandates a minimum of 100 ms
> between VBUS power-on and the first reset signalling for power settling.
> On root hubs, hub_power_on_good_delay() returns bPwrOn2PwrGood * 2 with
> no minimum floor; on the tested xHCI root hub bPwrOn2PwrGood = 10, yielding
> only 20 ms — well below the spec minimum. (External hubs already enforce
> a 100 ms minimum via hub_power_on_good_delay().) When _PRR._RST has been
> exercised the device must also complete its full power-on sequence (GPIO
> de-assertion, internal oscillator start, firmware load) before USB
> enumeration begins. The 100 ms sleep enforces the spec minimum and gives
> the device adequate settling time.
>
> Tested on a Dell laptop with MT7925 Bluetooth (idVendor=0489,
> idProduct=e139) whose BT_RST GPIO was stuck low. With this fix the
> device recovers autonomously at boot without requiring a G3
> (mechanical power-off) cycle. The relevant dmesg sequence:
>
> [ 1.448491] usb 3-10: new high-speed USB device number 4 using xhci_hcd
> [ 6.813942] usb 3-10: device descriptor read/64, error -110
> [ 22.685978] usb 3-10: device descriptor read/64, error -110
> [ 22.901715] usb 3-10: new high-speed USB device number 5 using xhci_hcd
> [ 28.317963] usb 3-10: device descriptor read/64, error -110
> [ 44.189949] usb 3-10: device descriptor read/64, error -110
> [ 44.294065] usb usb3-port10: attempt power cycle
> [ 44.872709] usb 3-10: new high-speed USB device number 6 using xhci_hcd
> [ 44.888293] usb 3-10: New USB device found, idVendor=0489, idProduct=e139, bcdDevice= 1.00
> [ 44.888318] usb 3-10: Manufacturer: MediaTek Inc.
>
> Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
> Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
> Link: https://patch.msgid.link/20260706080117.3754550-1-acelan.kao@canonical.com
> Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
> ---
> This was sent last cycle but got no feedback except for my review comment.
> I think we should bring it forward this cycle.
>
> Changes from v2:
> * Rebase on 7.4-rc1
> * Link to v2: https://lore.kernel.org/linux-usb/20260706080117.3754550-1-acelan.kao@canonical.com/
> ---
> drivers/usb/core/hub.c | 14 ++++++++++
> drivers/usb/core/usb-acpi.c | 68 +++++++++++++++++++++++++++++++++++++++++++++
> drivers/usb/core/usb.h | 3 ++
> 3 files changed, 85 insertions(+)
>
> diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
> index 199d3f535a891..72da7aea94cc4 100644
> --- a/drivers/usb/core/hub.c
> +++ b/drivers/usb/core/hub.c
> @@ -5621,11 +5621,25 @@ static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus,
>
> /* When halfway through our retry count, power-cycle the port */
> if (i == (PORT_INIT_TRIES - 1) / 2) {
> + int prr_reset;
> +
> dev_info(&port_dev->dev, "attempt power cycle\n");
> usb_hub_set_port_power(hdev, hub, port1, false);
> msleep(2 * hub_power_on_good_delay(hub));
> + prr_reset = usb_acpi_port_prr_reset(hdev, port1);
> usb_hub_set_port_power(hdev, hub, port1, true);
> msleep(hub_power_on_good_delay(hub));
> + /*
> + * USB 2.0 spec §7.1.7.3 requires at least 100 ms
> + * between VBUS power-on and the first reset for power
> + * settling. hub_power_on_good_delay() on an xHCI root
> + * hub returns bPwrOn2PwrGood * 2 with no minimum floor,
> + * which can be as little as 20 ms. When _PRR _RST was
> + * also exercised the device must complete its power-on
> + * sequence before enumeration; enforce the spec minimum.
> + */
> + if (prr_reset == 0)
> + msleep(100);
> }
> }
> if (hub->hdev->parent ||
> diff --git a/drivers/usb/core/usb-acpi.c b/drivers/usb/core/usb-acpi.c
> index 489dbdc96f94a..bb1b5e8cdc15e 100644
> --- a/drivers/usb/core/usb-acpi.c
> +++ b/drivers/usb/core/usb-acpi.c
> @@ -142,6 +142,74 @@ int usb_acpi_set_power_state(struct usb_device *hdev, int index, bool enable)
> }
> EXPORT_SYMBOL_GPL(usb_acpi_set_power_state);
>
> +/**
> + * usb_acpi_port_prr_reset - issue an ACPI _PRR reset on a hub port
> + * @hdev: USB device belonging to the usb hub
> + * @port1: port number (one-based)
> + *
> + * Some devices expose their hardware reset line via an ACPI Power Resource for
> + * Reset (_PRR). When such a device fails to enumerate (e.g. because the reset
> + * GPIO is stuck low), the USB power-cycle alone is not enough; the firmware
> + * reset path must also be exercised.
> + *
> + * This function evaluates _PRR on the port's ACPI companion to obtain the
> + * power-resource reference and then calls _RST on that resource to toggle the
> + * reset line. It is intended to be called alongside the mid-retry VBUS
> + * power-cycle already performed by hub_port_connect().
> + *
> + * Returns 0 on success, -ENODEV if the port has no ACPI handle or no _PRR
> + * method, or a negative error code on failure.
> + */
> +int usb_acpi_port_prr_reset(struct usb_device *hdev, int port1)
> +{
> + acpi_handle port_handle;
> + struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
> + union acpi_object *pkg, *ref;
> + acpi_status status;
> + int ret = 0;
> +
> + port_handle = usb_get_hub_port_acpi_handle(hdev, port1);
> + if (!port_handle)
> + return -ENODEV;
> +
> + if (!acpi_has_method(port_handle, "_PRR"))
> + return -ENODEV;
> +
> + status = acpi_evaluate_object(port_handle, "_PRR", NULL, &buffer);
> + if (ACPI_FAILURE(status)) {
> + dev_dbg(&hdev->dev, "port%d: _PRR evaluation failed: %s\n",
> + port1, acpi_format_exception(status));
> + return -ENODEV;
> + }
> +
> + pkg = buffer.pointer;
> + if (!pkg || pkg->type != ACPI_TYPE_PACKAGE || pkg->package.count != 1) {
> + dev_dbg(&hdev->dev, "port%d: _PRR returned unexpected object\n",
> + port1);
> + ret = -EINVAL;
> + goto out;
> + }
> +
> + ref = &pkg->package.elements[0];
> + if (ref->type != ACPI_TYPE_LOCAL_REFERENCE || !ref->reference.handle) {
> + dev_dbg(&hdev->dev, "port%d: _PRR element is not a reference\n",
> + port1);
> + ret = -EINVAL;
> + goto out;
> + }
> +
> + status = acpi_evaluate_object(ref->reference.handle, "_RST", NULL, NULL);
> + if (ACPI_FAILURE(status)) {
> + dev_dbg(&hdev->dev, "port%d: _RST evaluation failed: %s\n",
> + port1, acpi_format_exception(status));
> + ret = -EIO;
> + }
> +
> +out:
> + kfree(buffer.pointer);
> + return ret;
> +}
> +
> /**
> * usb_acpi_add_usb4_devlink - add device link to USB4 Host Interface for tunneled USB3 devices
> *
> diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
> index a9b37aeb515be..4d3dc3bd881b2 100644
> --- a/drivers/usb/core/usb.h
> +++ b/drivers/usb/core/usb.h
> @@ -211,7 +211,10 @@ extern int usb_acpi_register(void);
> extern void usb_acpi_unregister(void);
> extern acpi_handle usb_get_hub_port_acpi_handle(struct usb_device *hdev,
> int port1);
> +extern int usb_acpi_port_prr_reset(struct usb_device *hdev, int port1);
> #else
> static inline int usb_acpi_register(void) { return 0; };
> static inline void usb_acpi_unregister(void) { };
> +static inline int usb_acpi_port_prr_reset(struct usb_device *hdev,
> + int port1) { return -ENODEV; }
> #endif
>
> ---
> base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4
> change-id: 20260706080117.3754550-1-acelan.kao@canonical.com
>
> Best regards,
> --
> Mario Limonciello <superm1@kernel.org>
Hi Greg,
Ping on this patch please from a few weeks ago.
Thanks,
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH v3] USB: hub: call ACPI _PRR reset during port power-cycle on enumeration failure
2026-11-19 14:58 ` Mario Limonciello
@ 2026-11-19 15:10 ` Greg Kroah-Hartman
0 siblings, 0 replies; 4+ messages in thread
From: Greg Kroah-Hartman @ 2026-11-19 15:10 UTC (permalink / raw)
To: Mario Limonciello
Cc: linux-usb, linux-kernel, Rafael J. Wysocki, Mika Westerberg,
linux-acpi, Chia-Lin Kao (AceLan)
On Thu, Nov 19, 2026 at 08:58:32AM -0600, Mario Limonciello wrote:
> Ping on this patch please from a few weeks ago.
Sorry, due to a lot of flight delays (i.e. days) due to the mess in the
US last week, I've been on the road for an extra unexpected week.
Should hopefully catch up on pending patches "soon"...
thanks,
greg "what continent is this?" k-h
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2026-11-19 15:13 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-03 6:08 [PATCH v3] USB: hub: call ACPI _PRR reset during port power-cycle on enumeration failure Mario Limonciello
2026-11-03 6:18 ` sashiko-bot
2026-11-19 14:58 ` Mario Limonciello
2026-11-19 15:10 ` Greg Kroah-Hartman
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox