[Bug 218943] No SuperSpeedPlus on AM4/5 Hubs

[bugzilla-daemon@kernel.org]

https://bugzilla.kernel.org/show_bug.cgi?id=218943

--- Comment #17 from Jarrard (jarrard@proton.me) ---
Ok seems I'm a bit of a idiot and had secure boot enabled. 
Now the commands work. 

Got a whole bunch of stuff.

[  619.877598] xhci_hcd 0000:30:00.3: Get port status 4-4 read: 0xe2a1203,
return 0x310203
[  619.877612] xhci_hcd 0000:30:00.3: xhci_get_isoc_frame_id: index 0, reg
0x64b start_frame_id 0xca, end_frame_id 0x448, start_frame 0xd5
[  619.877627] xhci_hcd 0000:30:00.3: clear port4 reset change, portsc:
0xe0a1203
[  619.877641] xhci_hcd 0000:30:00.3: clear port4 warm(BH) reset change,
portsc: 0xe021203
[  619.877654] xhci_hcd 0000:30:00.3: clear port4 link state change, portsc:
0xe021203
[  619.877667] xhci_hcd 0000:30:00.3: clear port4 connect change, portsc:
0xe001203
[  619.877679] xhci_hcd 0000:30:00.3: Get port status 4-4 read: 0xe001203,
return 0x203
...
[  619.929597] xhci_hcd 0000:30:00.3: Set root hub portnum to 8
[  619.929602] xhci_hcd 0000:30:00.3: Set fake root hub portnum to 4
[  619.929606] xhci_hcd 0000:30:00.3: udev->tt = 0000000000000000
[  619.929610] xhci_hcd 0000:30:00.3: udev->ttport = 0x0
[  619.929616] xhci_hcd 0000:30:00.3: // Ding dong!
...
[  619.937709] usb 4-4: Device not responding to setup address.
[  619.937754] xhci_hcd 0000:30:00.3: // Ding dong!
[  619.937775] xhci_hcd 0000:30:00.3: // Ding dong!
[  619.937811] xhci_hcd 0000:30:00.3: Slot 7 output ctx = 0x0x00000000fffc2000
(dma)
[  619.937817] xhci_hcd 0000:30:00.3: Slot 7 input ctx = 0x0x00000000fff42000
(dma)
[  619.937823] xhci_hcd 0000:30:00.3: Set slot id 7 dcbaa entry
00000000dcd62c49 to 0xfffc2000
[  619.938588] xhci_hcd 0000:30:00.3: xhci_get_isoc_frame_id: index 0, reg
0x833 start_frame_id 0x107, end_frame_id 0x485, start_frame 0x112
[  619.938720] xhci_hcd 0000:30:00.3: Port change event, 4-4, id 8, portsc:
0xe0202a0
[  619.938726] xhci_hcd 0000:30:00.3: handle_port_status: starting usb4 port
polling.
...
[  620.141591] xhci_hcd 0000:30:00.3: Set root hub portnum to 8
[  620.141596] xhci_hcd 0000:30:00.3: Set fake root hub portnum to 4
[  620.141600] xhci_hcd 0000:30:00.3: udev->tt = 0000000000000000
[  620.141604] xhci_hcd 0000:30:00.3: udev->ttport = 0x0
[  620.141610] xhci_hcd 0000:30:00.3: // Ding dong!
...
[  620.149708] usb 4-4: Device not responding to setup address.
[  620.149752] xhci_hcd 0000:30:00.3: // Ding dong!
[  620.149774] xhci_hcd 0000:30:00.3: // Ding dong!
[  620.149810] xhci_hcd 0000:30:00.3: Slot 7 output ctx = 0x0x00000000fffc2000
(dma)
[  620.149816] xhci_hcd 0000:30:00.3: Slot 7 input ctx = 0x0x00000000fff42000
(dma)
[  620.149822] xhci_hcd 0000:30:00.3: Set slot id 7 dcbaa entry
00000000dcd62c49 to 0xfffc2000
...
[  620.357571] usb 4-4: device not accepting address 19, error -71
[  620.357587] xhci_hcd 0000:30:00.3: xhci_get_isoc_frame_id: index 0, reg
0x154b start_frame_id 0x2aa, end_frame_id 0x628, start_frame 0x2b5
...
[  620.365636] xhci_hcd 0000:30:00.3: // Ding dong!
[  620.365655] xhci_hcd 0000:30:00.3: Bad real port.
[  620.365662] usb usb4-port4: attempt power cycle
[  620.365668] xhci_hcd 0000:30:00.3: set port power 4-4 OFF, portsc: 0xe021263
...
[  620.573567] xhci_hcd 0000:30:00.3: set port power 4-4 ON, portsc: 0xe020080
...

-- 
You may reply to this email to add a comment.

You are receiving this mail because:
You are watching the assignee of the bug.