[PATCH 20/23] wifi: mt76: mt7925: disable only the RX NAPI instances that exist

[Sean Wang <sean.wang@kernel.org>]

From: Jacobs Wu <jacobs.wu@mediatek.com>

mt7925e_mac_reset() picks the RX NAPI instances to disable from the
interrupt masks, but the instances themselves are created per allocated
RX queue by mt76_dma_init(). On mt7925 the two do not agree: the tx-done
ring is only described by the mt7928 DMA layout, so q_rx[MT_RXQ_MCU_WA]
is never allocated and never gets a NAPI, while mt7925_irq_map still
carries rx.wm2_complete_mask.

A MAC reset therefore calls napi_disable() on an instance whose
net_device pointer is NULL. The fault happens inside napi_disable()
while the reset work holds the RTNL, so networking goes down with it and
the machine is left answering ping with no usable userspace; only a
power cycle recovers it. Repeated NAN data path setup and teardown hits
this reliably on a busy channel, where MAC resets are frequent.

Iterate the RX queues instead, the same way the restore path further
down re-enables them, so only instances that were actually added are
touched.

Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jacobs Wu <jacobs.wu@mediatek.com>
---
 .../wireless/mediatek/mt76/mt7925/pci_mac.c   | 19 +++++++++++++------
 1 file changed, 13 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7925/pci_mac.c b/drivers/net/wireless/mediatek/mt76/mt7925/pci_mac.c
index 6e9daf96da88..32463ef30ebb 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7925/pci_mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7925/pci_mac.c
@@ -127,12 +127,19 @@ int mt7925e_mac_reset(struct mt792x_dev *dev)
 	mt76_txq_schedule_all(&dev->mphy);
 
 	mt76_worker_disable(&dev->mt76.tx_worker);
-	if (irq_map->rx.data_complete_mask)
-		napi_disable(&dev->mt76.napi[MT_RXQ_MAIN]);
-	if (irq_map->rx.wm_complete_mask)
-		napi_disable(&dev->mt76.napi[MT_RXQ_MCU]);
-	if (irq_map->rx.wm2_complete_mask)
-		napi_disable(&dev->mt76.napi[MT_RXQ_MCU_WA]);
+
+	/*
+	 * Disable the RX NAPI instances that were actually created. They are
+	 * added per allocated RX queue by mt76_dma_init(), while the interrupt
+	 * masks describe what the hardware is able to raise - on mt7925 the
+	 * tx-done queue is never allocated (only mt7928 defines that ring), so
+	 * its NAPI has no net_device and napi_disable() faults on it while
+	 * holding the RTNL, wedging the whole machine. Iterate the queues, the
+	 * same way the restore path below re-enables them.
+	 */
+	mt76_for_each_q_rx(&dev->mt76, i)
+		napi_disable(&dev->mt76.napi[i]);
+
 	if (irq_map->tx.all_complete_mask)
 		napi_disable(&dev->mt76.tx_napi);
 
-- 
2.43.0