From: Ping-Ke Shih <pkshih@realtek.com>
To: <linux-wireless@vger.kernel.org>
Cc: <ku920601@realtek.com>, <damon.chen@realtek.com>,
<phhuang@realtek.com>, <kevin_yang@realtek.com>
Subject: [PATCH rtw-next 02/11] wifi: rtw89: pci: reclaim TXBD before fully draining
Date: Thu, 12 Nov 2026 14:05:51 +0800 [thread overview]
Message-ID: <20261112060600.71784-3-pkshih@realtek.com> (raw)
In-Reply-To: <20261112060600.71784-1-pkshih@realtek.com>
From: Kuan-Chung Chen <damon.chen@realtek.com>
Currently, we reclaim TXBD only when the available resource is 0.
When two ACs share the same DMA channel, the lower-priority AC
occupies the whole channel, which affects the higher-priority
AC's throughput.
Add RTW89_PCI_TXBD_RECLAIM_TH to reclaim early once the
available resource falls below it, improving TX
fairness between ACs sharing a DMA channel.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
---
drivers/net/wireless/realtek/rtw89/pci.c | 4 ++--
drivers/net/wireless/realtek/rtw89/pci.h | 1 +
2 files changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/realtek/rtw89/pci.c b/drivers/net/wireless/realtek/rtw89/pci.c
index 6d19e759fc0d..76523d057825 100644
--- a/drivers/net/wireless/realtek/rtw89/pci.c
+++ b/drivers/net/wireless/realtek/rtw89/pci.c
@@ -1281,7 +1281,7 @@ static u32 __rtw89_pci_check_and_reclaim_tx_resource(struct rtw89_dev *rtwdev,
bd_cnt = rtw89_pci_get_avail_txbd_num(tx_ring);
wd_cnt = wd_ring->curr_num;
- if (wd_cnt == 0 || bd_cnt == 0) {
+ if (wd_cnt == 0 || bd_cnt < RTW89_PCI_TXBD_RECLAIM_TH) {
cnt = rtw89_pci_rxbd_recalc(rtwdev, rx_ring);
if (cnt)
rtw89_pci_release_tx(rtwdev, rx_ring, cnt);
@@ -1289,7 +1289,7 @@ static u32 __rtw89_pci_check_and_reclaim_tx_resource(struct rtw89_dev *rtwdev,
goto out_unlock;
bd_cnt = rtw89_pci_get_avail_txbd_num(tx_ring);
- if (bd_cnt == 0)
+ if (bd_cnt < RTW89_PCI_TXBD_RECLAIM_TH)
rtw89_pci_reclaim_txbd(rtwdev, tx_ring);
}
diff --git a/drivers/net/wireless/realtek/rtw89/pci.h b/drivers/net/wireless/realtek/rtw89/pci.h
index 0f9ea4bf54ea..3cc484bc1ca8 100644
--- a/drivers/net/wireless/realtek/rtw89/pci.h
+++ b/drivers/net/wireless/realtek/rtw89/pci.h
@@ -1120,6 +1120,7 @@
#define B_BE_MAX_TAG_NUM_MASK GENMASK(3, 0)
#define RTW89_PCI_TXBD_NUM_MAX 256
+#define RTW89_PCI_TXBD_RECLAIM_TH (RTW89_PCI_TXBD_NUM_MAX >> 1)
#define RTW89_PCI_RXBD_NUM_MAX 256
#define RTW89_PCI_TXWD_NUM_MAX 512
#define RTW89_PCI_TXWD_PAGE_SIZE 128
--
2.53.0
next prev parent reply other threads:[~2026-11-12 6:06 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-12 6:05 [PATCH rtw-next 00/11] wifi: rtw89: correct no 2GHz band condition, update RTL8922D settings Ping-Ke Shih
2026-11-12 6:05 ` [PATCH rtw-next 01/11] wifi: rtw89: coex: add a notify entry for dynamic MLO RF-path switch Ping-Ke Shih
2026-11-12 6:05 ` Ping-Ke Shih [this message]
2026-11-12 6:05 ` [PATCH rtw-next 03/11] wifi: rtw89: 8922d: use efuse bias for CCK RX gain Ping-Ke Shih
2026-11-12 6:05 ` [PATCH rtw-next 04/11] wifi: rtw89: 8922d: set CFR clip threshold while setting channel Ping-Ke Shih
2026-11-12 6:05 ` [PATCH rtw-next 05/11] wifi: rtw89: 8922d: correct thermal trim range to -16~+16 programmed in efuse Ping-Ke Shih
2026-11-12 6:05 ` [PATCH rtw-next 06/11] wifi: rtw89: introduce bitmap of supported bands to deal with quirks Ping-Ke Shih
2026-11-12 6:05 ` [PATCH rtw-next 07/11] wifi: rtw89: get default channel based on supported bands Ping-Ke Shih
2026-11-12 6:05 ` [PATCH rtw-next 08/11] wifi: rtw89: fix band assignment in rtw89_core_update_rx_freq_from_ie() Ping-Ke Shih
2026-11-12 6:05 ` [PATCH rtw-next 09/11] wifi: rtw89: Update sequence for MLO link switch Ping-Ke Shih
2026-11-12 6:05 ` [PATCH rtw-next 10/11] wifi: rtw89: 8922d: enable dynamic antenna gain Ping-Ke Shih
2026-11-12 6:06 ` [PATCH rtw-next 11/11] wifi: rtw89: phy: fix antenna gain unit in debug output Ping-Ke Shih
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261112060600.71784-3-pkshih@realtek.com \
--to=pkshih@realtek.com \
--cc=damon.chen@realtek.com \
--cc=kevin_yang@realtek.com \
--cc=ku920601@realtek.com \
--cc=linux-wireless@vger.kernel.org \
--cc=phhuang@realtek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox