From: Felix Fietkau <nbd@nbd.name>
To: linux-wireless@vger.kernel.org
Subject: [PATCH mt76-next 13/17] wifi: mt76: mt7996: abort a background CAC at a full reset
Date: Sat, 21 Nov 2026 13:09:22 +0100 [thread overview]
Message-ID: <20261121120926.3603979-13-nbd@nbd.name> (raw)
In-Reply-To: <20261121120926.3603979-1-nbd@nbd.name>
A full reset reloads the firmware, which then runs no background radar
chain, and nothing tells cfg80211. A background CAC in progress thus
goes on without radar detection, and cfg80211 marks its channel
available when the CAC time ends.
Report the CAC aborted to cfg80211 after the firmware reload. cfg80211
then stops the chain through the driver, which clears dev->rdd2_phy,
and user space can start a new CAC. A restart of the chain would leave
a gap without radar detection in the CAC.
Fixes: 27015b6fbcca ("wifi: mt76: mt7996: enable full system reset support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mt7996/mac.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7996/mac.c b/drivers/net/wireless/mediatek/mt76/mt7996/mac.c
index 62f3ac2b2cd2..cf8d57b7b5bb 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7996/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7996/mac.c
@@ -2555,6 +2555,9 @@ mt7996_mac_full_reset(struct mt7996_dev *dev)
if (i == 10)
dev_err(dev->mt76.dev, "chip full reset failed\n");
+ if (dev->rdd2_phy)
+ cfg80211_background_cac_abort(dev->rdd2_phy->mt76->hw->wiphy);
+
mt7996_for_each_phy(dev, phy) {
phy->omac_mask = 0;
phy->rxfilter |= MT_WF_RFCR_DROP_OTHER_UC;
--
2.47.3
next prev parent reply other threads:[~2026-11-21 12:09 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-21 12:09 [PATCH mt76-next 01/17] wifi: mt76: mt7996: name a new secondary link to the firmware first Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 02/17] wifi: mt76: add a helper to point the TXQs of a station at a wcid Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 03/17] wifi: mt76: mt7925: move the default link to a remaining link Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 04/17] wifi: mt76: mt7925: keep the deflink wcid index until station removal Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 05/17] wifi: mt76: mt792x: look up the TX links under RCU Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 06/17] wifi: mt76: mt7925: read the links under RCU in the IPv6 notifier Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 07/17] wifi: mt76: mt7925: abort a ROC on the BSS that requested it Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 08/17] wifi: mt76: mt7925: take the link conf of a removed link from old[] Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 09/17] wifi: mt76: mt7925: send the MLO ROC only for a station vif Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 10/17] wifi: mt76: mt7996: send the Beacon rate table again after a full reset Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 11/17] wifi: mt76: mt7996: restore the operating channel after an L1 SER Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 12/17] wifi: mt76: reset the DFS state of a phy at a full reset Felix Fietkau
2026-11-21 12:09 ` Felix Fietkau [this message]
2026-11-21 12:09 ` [PATCH mt76-next 14/17] wifi: mt76: mt7915: abort a background CAC " Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 15/17] wifi: mt76: mt7996: clear the airtime counts with the WTBL counters Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 16/17] wifi: mt76: mt7996: drop the host WTBL write of a fixed GI Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 17/17] wifi: mt76: mt7925: don't reset the USB device on probe Felix Fietkau
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261121120926.3603979-13-nbd@nbd.name \
--to=nbd@nbd.name \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox