Linux wireless drivers development
 help / color / mirror / Atom feed
From: Felix Fietkau <nbd@nbd.name>
To: linux-wireless@vger.kernel.org
Subject: [PATCH mt76-next 17/17] wifi: mt76: mt7925: don't reset the USB device on probe
Date: Sat, 21 Nov 2026 13:09:26 +0100	[thread overview]
Message-ID: <20261121120926.3603979-17-nbd@nbd.name> (raw)
In-Reply-To: <20261121120926.3603979-1-nbd@nbd.name>

mt7925u_probe() resets the whole USB device. On MT7925 modules that
expose Bluetooth on the same device, this also hits the interfaces
that btusb drives. btusb has no pre_reset/post_reset handlers, so the
reset unbinds it while it sets up the controller.

Drop the reset, like mt7921u does. mt7925u_probe() still resets the
Wi-Fi subsystem with mt792xu_wfsys_reset() if the firmware is running.

Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
 drivers/net/wireless/mediatek/mt76/mt7925/usb.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7925/usb.c b/drivers/net/wireless/mediatek/mt76/mt7925/usb.c
index ee5306c29427..b1f6ef35fffb 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7925/usb.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7925/usb.c
@@ -190,7 +190,6 @@ static int mt7925u_probe(struct usb_interface *usb_intf,
 		.write_copy = mt792xu_copy,
 		.type = MT76_BUS_USB,
 	};
-	struct usb_device *udev = interface_to_usbdev(usb_intf);
 	struct ieee80211_ops *ops;
 	struct ieee80211_hw *hw;
 	struct mt792x_dev *dev;
@@ -214,8 +213,6 @@ static int mt7925u_probe(struct usb_interface *usb_intf,
 	dev->hif_ops = &hif_ops;
 	mt792xu_reset_work_init(dev);
 
-	usb_reset_device(udev);
-
 	usb_set_intfdata(usb_intf, dev);
 
 	ret = __mt76u_init(mdev, usb_intf, &bus_ops);
-- 
2.47.3


      parent reply	other threads:[~2026-11-21 12:09 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-21 12:09 [PATCH mt76-next 01/17] wifi: mt76: mt7996: name a new secondary link to the firmware first Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 02/17] wifi: mt76: add a helper to point the TXQs of a station at a wcid Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 03/17] wifi: mt76: mt7925: move the default link to a remaining link Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 04/17] wifi: mt76: mt7925: keep the deflink wcid index until station removal Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 05/17] wifi: mt76: mt792x: look up the TX links under RCU Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 06/17] wifi: mt76: mt7925: read the links under RCU in the IPv6 notifier Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 07/17] wifi: mt76: mt7925: abort a ROC on the BSS that requested it Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 08/17] wifi: mt76: mt7925: take the link conf of a removed link from old[] Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 09/17] wifi: mt76: mt7925: send the MLO ROC only for a station vif Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 10/17] wifi: mt76: mt7996: send the Beacon rate table again after a full reset Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 11/17] wifi: mt76: mt7996: restore the operating channel after an L1 SER Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 12/17] wifi: mt76: reset the DFS state of a phy at a full reset Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 13/17] wifi: mt76: mt7996: abort a background CAC " Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 14/17] wifi: mt76: mt7915: " Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 15/17] wifi: mt76: mt7996: clear the airtime counts with the WTBL counters Felix Fietkau
2026-11-21 12:09 ` [PATCH mt76-next 16/17] wifi: mt76: mt7996: drop the host WTBL write of a fixed GI Felix Fietkau
2026-11-21 12:09 ` Felix Fietkau [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20261121120926.3603979-17-nbd@nbd.name \
    --to=nbd@nbd.name \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox