From: Alexander Aring <alex.aring@gmail.com>
To: linux-wpan@vger.kernel.org
Cc: kernel@pengutronix.de, Alexander Aring <alex.aring@gmail.com>,
Varka Bhadram <varkabhadram@gmail.com>,
Alan Ott <alan@signal11.us>
Subject: [PATCHv2 wpan-next 04/16] ieee802154: introduce wpan_phy_supported
Date: Wed, 6 May 2015 13:40:16 +0200 [thread overview]
Message-ID: <1430912428-17284-5-git-send-email-alex.aring@gmail.com> (raw)
In-Reply-To: <1430912428-17284-1-git-send-email-alex.aring@gmail.com>
This patch introduce the wpan_phy_supported struct for wpan_phy. There
is currently no way to check if a transceiver can handle IEEE 802.15.4
complaint values. With this struct we can check before if the
transceiver supports these values before sending to driver layer.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Suggested-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Alan Ott <alan@signal11.us>
---
drivers/net/ieee802154/at86rf230.c | 8 ++++----
drivers/net/ieee802154/cc2520.c | 2 +-
drivers/net/ieee802154/fakelb.c | 30 +++++++++++++++---------------
drivers/net/ieee802154/mrf24j40.c | 2 +-
include/net/cfg802154.h | 6 +++++-
net/ieee802154/nl-phy.c | 4 ++--
net/ieee802154/nl802154.c | 4 ++--
7 files changed, 30 insertions(+), 26 deletions(-)
diff --git a/drivers/net/ieee802154/at86rf230.c b/drivers/net/ieee802154/at86rf230.c
index e68d45e..151d57f 100644
--- a/drivers/net/ieee802154/at86rf230.c
+++ b/drivers/net/ieee802154/at86rf230.c
@@ -1579,7 +1579,7 @@ at86rf230_detect_device(struct at86rf230_local *lp)
case 3:
chip = "at86rf231";
lp->data = &at86rf231_data;
- lp->hw->phy->channels_supported[0] = 0x7FFF800;
+ lp->hw->phy->supported.channels[0] = 0x7FFF800;
lp->hw->phy->current_channel = 11;
lp->hw->phy->symbol_duration = 16;
break;
@@ -1587,15 +1587,15 @@ at86rf230_detect_device(struct at86rf230_local *lp)
chip = "at86rf212";
lp->data = &at86rf212_data;
lp->hw->flags |= IEEE802154_HW_LBT;
- lp->hw->phy->channels_supported[0] = 0x00007FF;
- lp->hw->phy->channels_supported[2] = 0x00007FF;
+ lp->hw->phy->supported.channels[0] = 0x00007FF;
+ lp->hw->phy->supported.channels[2] = 0x00007FF;
lp->hw->phy->current_channel = 5;
lp->hw->phy->symbol_duration = 25;
break;
case 11:
chip = "at86rf233";
lp->data = &at86rf233_data;
- lp->hw->phy->channels_supported[0] = 0x7FFF800;
+ lp->hw->phy->supported.channels[0] = 0x7FFF800;
lp->hw->phy->current_channel = 13;
lp->hw->phy->symbol_duration = 16;
break;
diff --git a/drivers/net/ieee802154/cc2520.c b/drivers/net/ieee802154/cc2520.c
index f833b8b..84b28a0 100644
--- a/drivers/net/ieee802154/cc2520.c
+++ b/drivers/net/ieee802154/cc2520.c
@@ -653,7 +653,7 @@ static int cc2520_register(struct cc2520_private *priv)
ieee802154_random_extended_addr(&priv->hw->phy->perm_extended_addr);
/* We do support only 2.4 Ghz */
- priv->hw->phy->channels_supported[0] = 0x7FFF800;
+ priv->hw->phy->supported.channels[0] = 0x7FFF800;
priv->hw->flags = IEEE802154_HW_OMIT_CKSUM | IEEE802154_HW_AACK |
IEEE802154_HW_AFILT;
diff --git a/drivers/net/ieee802154/fakelb.c b/drivers/net/ieee802154/fakelb.c
index dc2bfb6..91bbf03 100644
--- a/drivers/net/ieee802154/fakelb.c
+++ b/drivers/net/ieee802154/fakelb.c
@@ -149,35 +149,35 @@ static int fakelb_add_one(struct device *dev, struct fakelb_priv *fake)
priv->hw = hw;
/* 868 MHz BPSK 802.15.4-2003 */
- hw->phy->channels_supported[0] |= 1;
+ hw->phy->supported.channels[0] |= 1;
/* 915 MHz BPSK 802.15.4-2003 */
- hw->phy->channels_supported[0] |= 0x7fe;
+ hw->phy->supported.channels[0] |= 0x7fe;
/* 2.4 GHz O-QPSK 802.15.4-2003 */
- hw->phy->channels_supported[0] |= 0x7FFF800;
+ hw->phy->supported.channels[0] |= 0x7FFF800;
/* 868 MHz ASK 802.15.4-2006 */
- hw->phy->channels_supported[1] |= 1;
+ hw->phy->supported.channels[1] |= 1;
/* 915 MHz ASK 802.15.4-2006 */
- hw->phy->channels_supported[1] |= 0x7fe;
+ hw->phy->supported.channels[1] |= 0x7fe;
/* 868 MHz O-QPSK 802.15.4-2006 */
- hw->phy->channels_supported[2] |= 1;
+ hw->phy->supported.channels[2] |= 1;
/* 915 MHz O-QPSK 802.15.4-2006 */
- hw->phy->channels_supported[2] |= 0x7fe;
+ hw->phy->supported.channels[2] |= 0x7fe;
/* 2.4 GHz CSS 802.15.4a-2007 */
- hw->phy->channels_supported[3] |= 0x3fff;
+ hw->phy->supported.channels[3] |= 0x3fff;
/* UWB Sub-gigahertz 802.15.4a-2007 */
- hw->phy->channels_supported[4] |= 1;
+ hw->phy->supported.channels[4] |= 1;
/* UWB Low band 802.15.4a-2007 */
- hw->phy->channels_supported[4] |= 0x1e;
+ hw->phy->supported.channels[4] |= 0x1e;
/* UWB High band 802.15.4a-2007 */
- hw->phy->channels_supported[4] |= 0xffe0;
+ hw->phy->supported.channels[4] |= 0xffe0;
/* 750 MHz O-QPSK 802.15.4c-2009 */
- hw->phy->channels_supported[5] |= 0xf;
+ hw->phy->supported.channels[5] |= 0xf;
/* 750 MHz MPSK 802.15.4c-2009 */
- hw->phy->channels_supported[5] |= 0xf0;
+ hw->phy->supported.channels[5] |= 0xf0;
/* 950 MHz BPSK 802.15.4d-2009 */
- hw->phy->channels_supported[6] |= 0x3ff;
+ hw->phy->supported.channels[6] |= 0x3ff;
/* 950 MHz GFSK 802.15.4d-2009 */
- hw->phy->channels_supported[6] |= 0x3ffc00;
+ hw->phy->supported.channels[6] |= 0x3ffc00;
INIT_LIST_HEAD(&priv->list);
priv->fake = fake;
diff --git a/drivers/net/ieee802154/mrf24j40.c b/drivers/net/ieee802154/mrf24j40.c
index fba2dfd..f2a1bd1 100644
--- a/drivers/net/ieee802154/mrf24j40.c
+++ b/drivers/net/ieee802154/mrf24j40.c
@@ -750,7 +750,7 @@ static int mrf24j40_probe(struct spi_device *spi)
devrec->hw->priv = devrec;
devrec->hw->parent = &devrec->spi->dev;
- devrec->hw->phy->channels_supported[0] = CHANNEL_MASK;
+ devrec->hw->phy->supported.channels[0] = CHANNEL_MASK;
devrec->hw->flags = IEEE802154_HW_OMIT_CKSUM | IEEE802154_HW_AACK |
IEEE802154_HW_AFILT;
diff --git a/include/net/cfg802154.h b/include/net/cfg802154.h
index 9ced2c9..1941d7a 100644
--- a/include/net/cfg802154.h
+++ b/include/net/cfg802154.h
@@ -61,6 +61,10 @@ struct cfg802154_ops {
struct wpan_dev *wpan_dev, bool mode);
};
+struct wpan_phy_supported {
+ u32 channels[IEEE802154_MAX_PAGE + 1];
+};
+
struct wpan_phy_cca {
enum nl802154_cca_modes mode;
enum nl802154_cca_opts opt;
@@ -84,7 +88,7 @@ struct wpan_phy {
*/
u8 current_channel;
u8 current_page;
- u32 channels_supported[IEEE802154_MAX_PAGE + 1];
+ struct wpan_phy_supported supported;
/* current transmit_power in mBm */
s32 transmit_power;
struct wpan_phy_cca cca;
diff --git a/net/ieee802154/nl-phy.c b/net/ieee802154/nl-phy.c
index 346c666..cbc0d09 100644
--- a/net/ieee802154/nl-phy.c
+++ b/net/ieee802154/nl-phy.c
@@ -56,8 +56,8 @@ static int ieee802154_nl_fill_phy(struct sk_buff *msg, u32 portid,
nla_put_u8(msg, IEEE802154_ATTR_CHANNEL, phy->current_channel))
goto nla_put_failure;
for (i = 0; i < 32; i++) {
- if (phy->channels_supported[i])
- buf[pages++] = phy->channels_supported[i] | (i << 27);
+ if (phy->supported.channels[i])
+ buf[pages++] = phy->supported.channels[i] | (i << 27);
}
if (pages &&
nla_put(msg, IEEE802154_ATTR_CHANNEL_PAGE_LIST,
diff --git a/net/ieee802154/nl802154.c b/net/ieee802154/nl802154.c
index f3185c7..d271879 100644
--- a/net/ieee802154/nl802154.c
+++ b/net/ieee802154/nl802154.c
@@ -248,7 +248,7 @@ nl802154_send_wpan_phy_channels(struct cfg802154_registered_device *rdev,
for (page = 0; page <= IEEE802154_MAX_PAGE; page++) {
if (nla_put_u32(msg, NL802154_ATTR_SUPPORTED_CHANNEL,
- rdev->wpan_phy.channels_supported[page]))
+ rdev->wpan_phy.supported.channels[page]))
return -ENOBUFS;
}
nla_nest_end(msg, nl_page);
@@ -626,7 +626,7 @@ static int nl802154_set_channel(struct sk_buff *skb, struct genl_info *info)
/* check 802.15.4 constraints */
if (page > IEEE802154_MAX_PAGE || channel > IEEE802154_MAX_CHANNEL ||
- !(rdev->wpan_phy.channels_supported[page] & BIT(channel)))
+ !(rdev->wpan_phy.supported.channels[page] & BIT(channel)))
return -EINVAL;
return rdev_set_channel(rdev, page, channel);
--
2.3.7
next prev parent reply other threads:[~2015-05-06 11:41 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-06 11:40 [PATCHv2 wpan-next 00/16] ieee802154: add support for phy capabilities Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 01/16] ieee802154: change transmit power to s32 Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 02/16] ieee802154: change transmit power to mbm Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 03/16] ieee802154: change cca ed level " Alexander Aring
2015-05-06 11:40 ` Alexander Aring [this message]
2015-05-06 11:40 ` [PATCHv2 wpan-next 05/16] ieee802154: add several phy supported handling Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 06/16] mac802154: check for really changes Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 07/16] mac802154: remove check if operation is supported Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 08/16] ieee802154: add iftypes capability Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 09/16] ieee802154: add support for get tx powers Alexander Aring
2015-05-06 12:02 ` Phoebe Buckheister
2015-05-06 13:19 ` Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 10/16] ieee802154: add support for get cca ed levels Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 11/16] at86rf230: set cca_modes supported flags Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 12/16] at86rf230: add reset states of tx power level Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 13/16] at86rf230: rework tx power support Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 14/16] at86rf230: rework tx cca energy detection level Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 15/16] ieee802154: check transmit power before driver layer Alexander Aring
2015-05-06 11:40 ` [PATCHv2 wpan-next 16/16] nl802154: add support for dump phy capabilities Alexander Aring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1430912428-17284-5-git-send-email-alex.aring@gmail.com \
--to=alex.aring@gmail.com \
--cc=alan@signal11.us \
--cc=kernel@pengutronix.de \
--cc=linux-wpan@vger.kernel.org \
--cc=varkabhadram@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox