* Re: No ttyS device at I/O port 0xfe004500 for console
From: Kumar Gala @ 2006-06-13 19:55 UTC (permalink / raw)
To: Alex Zeffertt; +Cc: linuxppc-embedded
In-Reply-To: <448EEC59.2010201@cambridgebroadband.com>
On Jun 13, 2006, at 11:48 AM, Alex Zeffertt wrote:
> Hi list,
>
> I'm trying to boot a linux-2.6.11 kernel on a MPC83xx based board.
> Through
> some experimentation I have found I need "console=uart,io,0xfe004500"
> in the kernel command line in order to get any output over the serial
> port.
>
> Half way through initialisation the kernel appears to swap from its
> "early"
> 8250 serial driver to a "full" 8250 serial driver. At this point
> it prints
> "No ttyS device at I/O port 0xfe004500 for console" and there is no
> further output.
>
> Does anyone have any idea what I may be doing wrong?
>
> BTW, here's the output that I do get.
Alex, where did you get this 2.6.11 kernel? The public tree didn't
have support for 83xx in 2.6.11. I'd suggest looking at using
something newer like 2.6.16 and see if you have the same issue.
- k
>
> -------------------/snip--------------------------
> U-Boot 1.1.3 (FSL Development) (Jun 13 2006 - 14:01:25) MPC83XX
>
> Clock configuration:
> Coherent System Bus: 132 MHz
> Core: 264 MHz
> QE: 198 MHz
> Local Bus Controller: 132 MHz
> Local Bus: 66 MHz
> DDR: 264 MHz
> SEC: 132 MHz
> I2C1: 132 MHz
> CPU: MPC8323E, Rev: 10 at 264 MHz
> Board: Freescale MPC832XEPB
> I2C: ready
> DRAM:
> DDR RAM: 128 MB
> FLASH: 16 MB
> In: serial
> Out: serial
> Err: serial
> Net: FSL GETH0
> Hit any key to stop autoboot: 0
> geth: PHY is Davicom DM9161A (181b8a0)
> FSL GETH0: Full Duplex
> FSL GETH0: Speed 100BT
> FSL GETH0: Link is up
> Using FSL GETH0 device
> TFTP from server 10.0.0.107; our IP address is 10.0.6.65
> Filename 'uImage'.
> Load address: 0x200000
> Loading:
> #################################################################
>
> #################################################################
>
> #################################################################
> ##########
> done
> Bytes transferred = 1046491 (ff7db hex)
> ## Booting image at 00200000 ...
> Image Name: Linux-2.6.11
> Image Type: PowerPC Linux Kernel Image (gzip compressed)
> Data Size: 1046427 Bytes = 1021.9 kB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
> Uncompressing Kernel Image ... OK
> Linux version 2.6.11 (ajz@zambia) (gcc version 3.4.3) #5 Tue Jun 13
> 17:36:46 BST 2006
> Built 1 zonelists
> Kernel command line: root=/dev/nfs rw nfsroot=10.0.0.107:/opt/eldk/
> ppc_6xx ip=10.0.6.65:10.0.0.107:10.0.0.1:255.255.0.0:eth0:off
> console=uart,io,0xfe004500
> IPIC (128 IRQ sources, 8 External IRQs) at fe000700
> QE IC (64 IRQ sources) at fe100080
> PID hash table entries: 1024 (order: 10, 16384 bytes)
> Early serial console at I/O port 0xfe004500 (options '134')
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 127488k available (1724k kernel code, 432k data, 100k init,
> 0k highmem)
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> NET: Registered protocol family 16
> SCSI subsystem initialized
> JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
> Generic RTC Driver v1.07
> Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing
> disabled
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
> loop: loaded (max 8 devices)
> MPC832XE MDS flash device: 1000000 at ff000000 Partition number 5
> MPC832XE PB Flash Map Info: Found 1 x16 devices at 0x0 in 16-bit bank
> Intel/Sharp Extended Query Table at 0x0031
> Using buffer write method
> cfi_cmdset_0001: Erase suspend on write enabled
> Creating 5 MTD partitions on "MPC832XE PB Flash Map Info":
> 0x00000000-0x00020000 : "HRCW"
> 0x00020000-0x00900000 : "JFFS2"
> 0x00900000-0x00d00000 : "Ramdisk"
> 0x00d00000-0x00f00000 : "Kernel"
> 0x00f00000-0x01000000 : "U-Boot"
> MPC832XE MDS flash device initialized
> i2c /dev entries driver
> NET: Registered protocol family 2
> IP: routing cache hash table of 1024 buckets, 8Kbytes
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> No ttyS device at I/O port 0xfe004500 for console
>
> -------------------/snip--------------------------
>
>
>
> TIA,
>
> Alex
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
^ permalink raw reply
* smc2 without hw handshake
From: Antonio Di Bacco @ 2006-06-13 19:51 UTC (permalink / raw)
To: linuxppc-embedded
Hi all,
I'm using the SMC2 serial device of MPC880 without using hardware handshake. I
use only tx and rx at a speed of 9600. Could it work? The driver I use is
included in linux 2.4.25 from denx.
Bye,
Antonio.
^ permalink raw reply
* No ttyS device at I/O port 0xfe004500 for console
From: Alex Zeffertt @ 2006-06-13 16:48 UTC (permalink / raw)
To: linuxppc-embedded
Hi list,
I'm trying to boot a linux-2.6.11 kernel on a MPC83xx based board. Through
some experimentation I have found I need "console=uart,io,0xfe004500"
in the kernel command line in order to get any output over the serial
port.
Half way through initialisation the kernel appears to swap from its "early"
8250 serial driver to a "full" 8250 serial driver. At this point it prints
"No ttyS device at I/O port 0xfe004500 for console" and there is no
further output.
Does anyone have any idea what I may be doing wrong?
BTW, here's the output that I do get.
-------------------/snip--------------------------
U-Boot 1.1.3 (FSL Development) (Jun 13 2006 - 14:01:25) MPC83XX
Clock configuration:
Coherent System Bus: 132 MHz
Core: 264 MHz
QE: 198 MHz
Local Bus Controller: 132 MHz
Local Bus: 66 MHz
DDR: 264 MHz
SEC: 132 MHz
I2C1: 132 MHz
CPU: MPC8323E, Rev: 10 at 264 MHz
Board: Freescale MPC832XEPB
I2C: ready
DRAM:
DDR RAM: 128 MB
FLASH: 16 MB
In: serial
Out: serial
Err: serial
Net: FSL GETH0
Hit any key to stop autoboot: 0
geth: PHY is Davicom DM9161A (181b8a0)
FSL GETH0: Full Duplex
FSL GETH0: Speed 100BT
FSL GETH0: Link is up
Using FSL GETH0 device
TFTP from server 10.0.0.107; our IP address is 10.0.6.65
Filename 'uImage'.
Load address: 0x200000
Loading: #################################################################
#################################################################
#################################################################
##########
done
Bytes transferred = 1046491 (ff7db hex)
## Booting image at 00200000 ...
Image Name: Linux-2.6.11
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1046427 Bytes = 1021.9 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.6.11 (ajz@zambia) (gcc version 3.4.3) #5 Tue Jun 13 17:36:46 BST 2006
Built 1 zonelists
Kernel command line: root=/dev/nfs rw nfsroot=10.0.0.107:/opt/eldk/ppc_6xx ip=10.0.6.65:10.0.0.107:10.0.0.1:255.255.0.0:eth0:off console=uart,io,0xfe004500
IPIC (128 IRQ sources, 8 External IRQs) at fe000700
QE IC (64 IRQ sources) at fe100080
PID hash table entries: 1024 (order: 10, 16384 bytes)
Early serial console at I/O port 0xfe004500 (options '134')
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 127488k available (1724k kernel code, 432k data, 100k init, 0k highmem)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
NET: Registered protocol family 16
SCSI subsystem initialized
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
MPC832XE MDS flash device: 1000000 at ff000000 Partition number 5
MPC832XE PB Flash Map Info: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 5 MTD partitions on "MPC832XE PB Flash Map Info":
0x00000000-0x00020000 : "HRCW"
0x00020000-0x00900000 : "JFFS2"
0x00900000-0x00d00000 : "Ramdisk"
0x00d00000-0x00f00000 : "Kernel"
0x00f00000-0x01000000 : "U-Boot"
MPC832XE MDS flash device initialized
i2c /dev entries driver
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
No ttyS device at I/O port 0xfe004500 for console
-------------------/snip--------------------------
TIA,
Alex
^ permalink raw reply
* Re: [PATCH] Compile failure fix for ppc on 2.6.17-rc4-mm3 (2nd attempt)
From: Mel Gorman @ 2006-06-13 16:49 UTC (permalink / raw)
To: Paul Mackerras; +Cc: Andrew Morton, linuxppc-dev, vgoyal, linux-kernel
In-Reply-To: <17545.16696.195276.334774@cargo.ozlabs.ibm.com>
On (09/06/06 19:36), Paul Mackerras didst pronounce:
> Mel Gorman writes:
>
> > + res->end = -(-res->end & ~(unsigned long)mask); \
> > + res->end += mask; \
>
> I think this is equivalent to
>
> res->end = (res->end + mask) | mask;
>
> and I have to say the latter seems more understandable to me (and
> doesn't need a cast) ...
>
Makes sense. The patch on top of the latest -mm is below if you want to push
it. It has not been boot tested as building with the latest -mm is broken
at the moment for older powerpcs because of the git-powerpc.patch patch .
That patch assumes that mm_context_t is a struct with a vdso_base which is
not always the case (it's an unsigned long in include/asm-ppc/mmu.h).
diff -rup -X /usr/src/patchset-0.6/bin//dontdiff linux-2.6.17-rc6-mm2-clean/arch/powerpc/kernel/pci_32.c linux-2.6.17-rc6-mm2-resources/arch/powerpc/kernel/pci_32.c
--- linux-2.6.17-rc6-mm2-clean/arch/powerpc/kernel/pci_32.c 2006-06-13 17:25:39.000000000 +0100
+++ linux-2.6.17-rc6-mm2-resources/arch/powerpc/kernel/pci_32.c 2006-06-13 17:30:20.000000000 +0100
@@ -1121,9 +1121,8 @@ check_for_io_childs(struct pci_bus *bus,
* e.g. res->end of 0x1fff moves to 0x2fff
*/
#define push_end(res, mask) do { \
- BUG_ON(((mask+1) & mask) != 0); \
- res->end = -(-res->end & ~(unsigned long)mask); \
- res->end += mask; \
+ BUG_ON(((mask+1) & mask) != 0); \
+ res->end = (res->end + mask) | mask; \
} while (0)
list_for_each_entry(dev, &bus->devices, bus_list) {
--
Mel Gorman
Part-time Phd Student Linux Technology Center
University of Limerick IBM Dublin Software Lab
^ permalink raw reply
* RE: OpenFirmware framebuffer
From: Matt Sealey @ 2006-06-13 16:27 UTC (permalink / raw)
To: 'Nathan Lynch'; +Cc: linuxppc-dev
In-Reply-To: <20060613161115.GB26750@localdomain>
Gentoo 2.6.15-r5 from the 2006.0 install CD.
It says "Welcome to Linux gentoo-2.6.15-r5" and then I see four
lines, MSR, HID0 and hex printout of each.
That's it.
I get the usual messages spooled to the serial console. My args are;
boot cd /boot/pegasos console=ttyS1,115200,8n1 console=tty0 init=/linuxrc looptype=squashfs loop=/image.squashfs udev nodevfs cdroot
root=/dev/ram0 video=ofonly
--
Matt Sealey <matt@genesi-usa.com>
Manager, Genesi, Developer Relations
> -----Original Message-----
> From: Nathan Lynch [mailto:ntl@pobox.com]
> Sent: Tuesday, June 13, 2006 11:11 AM
> To: Matt Sealey
> Cc: linuxppc-dev@ozlabs.org
> Subject: Re: OpenFirmware framebuffer
>
> Matt Sealey wrote:
> >
> > I just booted up my Pegasos and tried the offb driver for
> display and
> > was rather disappointed. It just displays 4 lines about
> HID0 and stuff
> > and then waits around.
> >
> > Is this all there is? Is there nothing more? Can't I get a
> scrolling
> > kernel output, and a penguin logo or am I missing the point? :)
>
> Maybe someone can help if you give more details, e.g. the
> kernel version, and exactly what messages are displayed
> before it hangs.
>
>
^ permalink raw reply
* Re: help with inittab
From: Anantharaman Chetan-W16155 @ 2006-06-13 16:26 UTC (permalink / raw)
To: dhlii; +Cc: linuxppc-embedded
In-Reply-To: <mailman.9.1150164003.18626.linuxppc-embedded@ozlabs.org>
I've tried what you've mentioned below, i.e removing the /sbin/init and
just having the /bin/sh in the init/main.c file and I don't get a
standalone shell. I am having a Linux 2.4 Kernel (Montavista 3.1)
running on a PPC405 in a Xilinx Virtex4 FX100 FPGA.
You mentioned it could be a hardware problem. Are there any errata which
could explain the h/w bug?=20
Thanks,
Chetan Anantharaman
----------------------------------------------------------------------
Message: 1
Date: Sun, 11 Jun 2006 22:02:02 -0400
From: "David H. Lynch Jr." <dhlii@dlasys.net>
Subject: Re: help with inittab
Cc: Chris Dumoulin <cdumoulin@ics-ltd.com>,
linuxppc-embedded@ozlabs.org
Message-ID: <448CCB1A.409@dlasys.net>
Content-Type: text/plain; charset=3DISO-8859-1
=20
For debugging or single user purposes you do not need to run init or
have an inittab.
There have been several sugestions that there may be a hardware
problem - there are a number that are possible.
I was stalled here for some time because my UartDriver was
accidentally using the physical IO address instead of the virtual one
and I had created a temporary phys=3Dvirtual entry in the tbl that =
was
conveniently getting blow away just here.
You can try to isolate your problem by changing your boot ramdisk
(inramfs or initrd)
Eliminate or rename /init /sbin/init /linuxrc and any of the other
permutations that linux tries to execute in init/main.c they are all
listed very near where you stopped.
make sure you have /bin/sh
reboot on that ramdisk if you have an "init" related problem then
you should get a standalone shell.
If you have a hardware problem you will likely still stop at the
same place.
=20
--=20
Dave Lynch DLA Systems
Software Development: Embedded Linux
717.627.3770 dhlii@dlasys.net http://www.dlasys.net
fax: 1.253.369.9244 Cell: 1.717.587.7774
Over 25 years' experience in platforms, languages, and technologies too
numerous to list.
"Any intelligent fool can make things bigger and more complex... It
takes a touch of genius - and a lot of courage to move in the opposite
direction."
Albert Einstein
^ permalink raw reply
* Re: 32 bit userland on G5
From: Johannes Berg @ 2006-06-13 16:18 UTC (permalink / raw)
To: David Woodhouse; +Cc: linuxppc-dev list
In-Reply-To: <1150215340.2844.33.camel@hades.cambridge.redhat.com>
[-- Attachment #1: Type: text/plain, Size: 278 bytes --]
On Tue, 2006-06-13 at 17:15 +0100, David Woodhouse wrote:
> Nah. It isn't a valid assumption; just as it isn't valid to assume that
> your stack will _always_ be at about 0xbfffffff.
Ok.
Just curious though: Why does READ_IMPLIES_EXEC exist at all then?
johannes
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 793 bytes --]
^ permalink raw reply
* Re: 32 bit userland on G5
From: David Woodhouse @ 2006-06-13 16:15 UTC (permalink / raw)
To: Johannes Berg; +Cc: linuxppc-dev list
In-Reply-To: <1150214746.6305.3.camel@johannes>
On Tue, 2006-06-13 at 18:05 +0200, Johannes Berg wrote:
> Yeah, I was just thinking that there are programs relying on that and if
> they run in the 32-bit compat mode they might rightfully do so... Dunno.
Nah. It isn't a valid assumption; just as it isn't valid to assume that
your stack will _always_ be at about 0xbfffffff.
--
dwmw2
^ permalink raw reply
* Re: OpenFirmware framebuffer
From: Nathan Lynch @ 2006-06-13 16:11 UTC (permalink / raw)
To: Matt Sealey; +Cc: linuxppc-dev
In-Reply-To: <021501c68efd$bc311080$99dfdfdf@bakuhatsu.net>
Matt Sealey wrote:
>
> I just booted up my Pegasos and tried the offb driver for display and was
> rather disappointed. It just displays 4 lines about HID0 and stuff and then
> waits around.
>
> Is this all there is? Is there nothing more? Can't I get a scrolling kernel
> output, and a penguin logo or am I missing the point? :)
Maybe someone can help if you give more details, e.g. the kernel
version, and exactly what messages are displayed before it hangs.
^ permalink raw reply
* OpenFirmware framebuffer
From: Matt Sealey @ 2006-06-13 15:26 UTC (permalink / raw)
To: linuxppc-dev
I just booted up my Pegasos and tried the offb driver for display and was
rather disappointed. It just displays 4 lines about HID0 and stuff and then
waits around.
Is this all there is? Is there nothing more? Can't I get a scrolling kernel
output, and a penguin logo or am I missing the point? :)
--
Matt Sealey <matt@genesi-usa.com>
Manager, Genesi, Developer Relations
^ permalink raw reply
* [PATCH] make pmf irq_client functions safe against pmf interrupts coming in
From: Johannes Berg @ 2006-06-13 15:43 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: Andrew Morton, linuxppc-dev list
In-Reply-To: <1150192713.13958.52.camel@localhost.localdomain>
This fixes the pmf irq_client functions to be safe against pmf interrupts coming
in while a client is registered/unregistered.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
--- linux-2.6-git.orig/arch/powerpc/platforms/powermac/pfunc_core.c 2006-06-13 17:37:35.791076087 +0200
+++ linux-2.6-git/arch/powerpc/platforms/powermac/pfunc_core.c 2006-06-13 17:40:16.213632271 +0200
@@ -871,10 +871,17 @@ int pmf_register_irq_client(struct devic
spin_unlock_irqrestore(&pmf_lock, flags);
if (func == NULL)
return -ENODEV;
+
+ /* guard against manipulations of list */
mutex_lock(&pmf_irq_mutex);
if (list_empty(&func->irq_clients))
func->dev->handlers->irq_enable(func);
+
+ /* guard against pmf_do_irq while changing list */
+ spin_lock_irqsave(&pmf_lock, flags);
list_add(&client->link, &func->irq_clients);
+ spin_unlock_irqrestore(&pmf_lock, flags);
+
client->func = func;
mutex_unlock(&pmf_irq_mutex);
@@ -885,12 +892,19 @@ EXPORT_SYMBOL_GPL(pmf_register_irq_clien
void pmf_unregister_irq_client(struct pmf_irq_client *client)
{
struct pmf_function *func = client->func;
+ unsigned long flags;
BUG_ON(func == NULL);
+ /* guard against manipulations of list */
mutex_lock(&pmf_irq_mutex);
client->func = NULL;
+
+ /* guard against pmf_do_irq while changing list */
+ spin_lock_irqsave(&pmf_lock, flags);
list_del(&client->link);
+ spin_unlock_irqrestore(&pmf_lock, flags);
+
if (list_empty(&func->irq_clients))
func->dev->handlers->irq_disable(func);
mutex_unlock(&pmf_irq_mutex);
^ permalink raw reply
* Re: 32 bit userland on G5
From: Johannes Berg @ 2006-06-13 16:05 UTC (permalink / raw)
To: David Woodhouse; +Cc: linuxppc-dev list
In-Reply-To: <1150202709.12423.21.camel@hades.cambridge.redhat.com>
[-- Attachment #1: Type: text/plain, Size: 361 bytes --]
On Tue, 2006-06-13 at 13:45 +0100, David Woodhouse wrote:
> Why? Just because older hardware wasn't capable of enforcing the
> permissions, that doesn't mean that we shouldn't enforce them now.
Yeah, I was just thinking that there are programs relying on that and if
they run in the 32-bit compat mode they might rightfully do so... Dunno.
johannes
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 793 bytes --]
^ permalink raw reply
* Re: [PATCH] powerpc-genirq: Use generic_handle_irq()
From: Josh Boyer @ 2006-06-13 12:46 UTC (permalink / raw)
To: David Woodhouse; +Cc: Ingo Molnar, Thomas Gleixner, linuxppc-dev list
In-Reply-To: <1150202394.12423.16.camel@hades.cambridge.redhat.com>
On Tue, 2006-06-13 at 13:39 +0100, David Woodhouse wrote:
> On Tue, 2006-06-13 at 05:51 -0500, Josh Boyer wrote:
> > It does? I only see arch/powerpc in the patch. Is arch/ppc hiding
> > somewhere else?
> >
> > And yes, arch/ppc still exists. We can debate that later ;).
>
> Did a maintainer step forward for it yet?
For arch/ppc? Not that I'm aware of. But that wasn't particularly my
point. The email says "This patch updates the ppc and powerpc
architectures..." when it doesn't.
I think most agree that arch/ppc needs to die via a complete migration
to arch/powerpc. But patches shouldn't claim to do something they
don't :).
josh
^ permalink raw reply
* Re: windfarm for PM72/PM73/RM31
From: Étienne Bersac @ 2006-06-13 12:46 UTC (permalink / raw)
To: Robin H. Johnson; +Cc: linuxppc-dev
In-Reply-To: <20060502001306.GA9589@curie-int.vc.shawcable.net>
Hello,
> The PID params portion will come together a bit later, please bug me by
> Wednesday next week if I haven't posted anything.
I'll get back my iMac G5 rev C in the next hours. So i'll be able to
test code. Have done some work about windfarm ?
Regards.
Étienne.
--
Verso l'Alto !
^ permalink raw reply
* Re: 32 bit userland on G5
From: David Woodhouse @ 2006-06-13 12:45 UTC (permalink / raw)
To: Johannes Berg; +Cc: linuxppc-dev list
In-Reply-To: <1150194348.9208.33.camel@johannes>
On Tue, 2006-06-13 at 12:25 +0200, Johannes Berg wrote:
> Since apparently the G5 honours no-execute permissions, shouldn't the 64
> bit kernel set the READ_IMPLIES_EXEC personality flag for 32-bit
> userland?
Why? Just because older hardware wasn't capable of enforcing the
permissions, that doesn't mean that we shouldn't enforce them now.
--
dwmw2
^ permalink raw reply
* Re: [PATCH] powerpc-genirq: Use generic_handle_irq()
From: David Woodhouse @ 2006-06-13 12:39 UTC (permalink / raw)
To: Josh Boyer; +Cc: Ingo Molnar, Thomas Gleixner, linuxppc-dev list
In-Reply-To: <1150195883.5618.6.camel@vader.jdub.homelinux.org>
On Tue, 2006-06-13 at 05:51 -0500, Josh Boyer wrote:
> It does? I only see arch/powerpc in the patch. Is arch/ppc hiding
> somewhere else?
>
> And yes, arch/ppc still exists. We can debate that later ;).
Did a maintainer step forward for it yet?
--
dwmw2
^ permalink raw reply
* Re: [PATCH] powerpc-genirq: Use generic_handle_irq()
From: Josh Boyer @ 2006-06-13 10:51 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev list, Ingo Molnar, Thomas Gleixner
In-Reply-To: <1150170472.13958.13.camel@localhost.localdomain>
On Tue, 2006-06-13 at 13:47 +1000, Benjamin Herrenschmidt wrote:
> This patch updates the ppc and powerpc architectures to use the new
> generic_handle_irq() so that interrupt controllers can be ported to the
> new genirq layer.
It does? I only see arch/powerpc in the patch. Is arch/ppc hiding
somewhere else?
And yes, arch/ppc still exists. We can debate that later ;).
josh
^ permalink raw reply
* Re: [PATCH] Fix builtin command line interaction with firmware
From: Segher Boessenkool @ 2006-06-13 10:45 UTC (permalink / raw)
To: Amos Waterland; +Cc: linuxppc-dev
In-Reply-To: <20060613034502.GA15130@kvasir.watson.ibm.com>
> It seems that prom_init's early_cmdline_parse is broken on at least
> Apple 970 xserves and IBM JS20 blades with SLOF. The firmware of
> these
> machines returns -1 and 1 respectively when getprop is called for the
> bootargs property of /chosen, causing Linux to ignore its builtin
> command line in favor of a null string. This patch makes Linux use
> its
> builtin command line if getprop returns an error or a null string.
If the user gave no boot arguments on the boot command, -1 and 1
are the only two valid return values even, and -1 is only valid
if no "boot" or "load" command was used to load the kernel.
Makes me wonder what those XServe's do ;-)
(0 isn't valid as the property is encoded with encode-string, which
puts a trailing 0 byte on the empty string. Doesn't hurt to check
for it anyway of course ;-) ).
> Signed-off-by: Amos Waterland <apw@us.ibm.com>
Looks good, thanks!
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
>
> ---
>
> arch/powerpc/kernel/prom_init.c | 2 +-
> 1 files changed, 1 insertions(+), 1 deletions(-)
>
> 0f0caf0342f39b4437dcb3e9f2f1d62bfb4e3e7d
> diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/
> prom_init.c
> index f70bd09..2e63a90 100644
> --- a/arch/powerpc/kernel/prom_init.c
> +++ b/arch/powerpc/kernel/prom_init.c
> @@ -574,7 +574,7 @@ static void __init early_cmdline_parse(v
> if ((long)_prom->chosen > 0)
> l = prom_getprop(_prom->chosen, "bootargs", p,
> COMMAND_LINE_SIZE-1);
> #ifdef CONFIG_CMDLINE
> - if (l == 0) /* dbl check */
> + if (l <= 0 || p[0] == '\0') /* dbl check */
> strlcpy(RELOC(prom_cmd_line),
> RELOC(CONFIG_CMDLINE), sizeof(prom_cmd_line));
> #endif /* CONFIG_CMDLINE */
> --
> 1.0.4
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
^ permalink raw reply
* 32 bit userland on G5
From: Johannes Berg @ 2006-06-13 10:25 UTC (permalink / raw)
To: linuxppc-dev list
[-- Attachment #1: Type: text/plain, Size: 413 bytes --]
Hi,
Since apparently the G5 honours no-execute permissions, shouldn't the 64
bit kernel set the READ_IMPLIES_EXEC personality flag for 32-bit
userland?
The memory being execute-protected is causing a mono bug
(http://bugzilla.ximian.com/show_bug.cgi?id=77028) but I'm not sure
where the correct fix would be, currently the kernel doesn't seem to be
behaving exactly the same on G4 and G5.
johannes
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 793 bytes --]
^ permalink raw reply
* Re: pmf_register_irq_client gives sleep with locks held warning
From: Benjamin Herrenschmidt @ 2006-06-13 9:58 UTC (permalink / raw)
To: Johannes Berg; +Cc: Andrew Morton, linuxppc-dev list
In-Reply-To: <1150188199.9208.7.camel@johannes>
> I see your patch is in, I'll make a patch that fixes it then instead of
> replacing it, I guess.
Please do, thanks.
Ben.
^ permalink raw reply
* Re: pmf_register_irq_client gives sleep with locks held warning
From: Johannes Berg @ 2006-06-13 8:43 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: Andrew Morton, linuxppc-dev list
In-Reply-To: <1149977097.12687.144.camel@localhost.localdomain>
[-- Attachment #1: Type: text/plain, Size: 705 bytes --]
On Sun, 2006-06-11 at 08:04 +1000, Benjamin Herrenschmidt wrote:
> > That's ok, we don't have any in-kernel users anyway. Alas the alsa
> > people will be dissatisfied because they like to ship new drivers for
> > old kernels or something. Oh well, I don't care.
>
> We still want people to build out-of-tree for 2.6.17 (please keep the
> git there for that), as it will take a while before 2.6.18 is here.
Sure, I'll continue maintaining snd-aoa in that repository.
> The remaining possible bug in the pmf irq code is probably harmless in
> 99.99% of the cases in practice :)
I see your patch is in, I'll make a patch that fixes it then instead of
replacing it, I guess.
johannes
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 793 bytes --]
^ permalink raw reply
* [PATCH/2.6.17-rc6 4/4 v2] Powerpc: mpc7448hpc2 (taiga) board con fig file
From: Zang Roy-r61911 @ 2006-06-13 7:07 UTC (permalink / raw)
To: Paul Mackerras, Benjamin Herrenschmidt
Cc: linuxppc-dev list, Alexandre.Bounine, Yang Xin-Xin-r48390
mpc7448 hpc2 (taiga) board config file
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
---
diff --git a/arch/powerpc/configs/mpc7448_hpc2_defconfig b/arch/powerpc/configs/mpc7448_hpc2_defconfig
new file mode 100644
index 0000000..15a50f4
--- /dev/null
+++ b/arch/powerpc/configs/mpc7448_hpc2_defconfig
@@ -0,0 +1,923 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.17-rc4
+# Sat May 27 18:45:55 2006
+#
+# CONFIG_PPC64 is not set
+CONFIG_PPC32=y
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_DEFAULT_UIMAGE=y
+
+#
+# Processor support
+#
+CONFIG_CLASSIC32=y
+# CONFIG_PPC_52xx is not set
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_8xx is not set
+# CONFIG_E200 is not set
+CONFIG_6xx=y
+CONFIG_PPC_FPU=y
+# CONFIG_ALTIVEC is not set
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_SMP is not set
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+# CONFIG_RELAY is not set
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_EMBEDDED=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
+
+#
+# Loadable module support
+#
+# CONFIG_MODULES is not set
+
+#
+# Block layer
+#
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MULTIPLATFORM is not set
+# CONFIG_PPC_ISERIES is not set
+CONFIG_EMBEDDED6xx=y
+# CONFIG_APUS is not set
+CONFIG_MPIC=y
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_TAU is not set
+# CONFIG_KATANA is not set
+# CONFIG_WILLOW is not set
+# CONFIG_CPCI690 is not set
+# CONFIG_POWERPMC250 is not set
+# CONFIG_CHESTNUT is not set
+# CONFIG_SPRUCE is not set
+# CONFIG_HDPU is not set
+# CONFIG_EV64260 is not set
+# CONFIG_LOPEC is not set
+# CONFIG_MVME5100 is not set
+# CONFIG_PPLUS is not set
+# CONFIG_PRPMC750 is not set
+# CONFIG_PRPMC800 is not set
+# CONFIG_SANDPOINT is not set
+CONFIG_MPC7448HPC2=y
+# CONFIG_RADSTONE_PPC7D is not set
+# CONFIG_PAL4 is not set
+# CONFIG_GEMINI is not set
+# CONFIG_EST8260 is not set
+# CONFIG_SBC82xx is not set
+# CONFIG_SBS8260 is not set
+# CONFIG_RPX8260 is not set
+# CONFIG_TQM8260 is not set
+# CONFIG_ADS8272 is not set
+# CONFIG_PQ2FADS is not set
+# CONFIG_LITE5200 is not set
+# CONFIG_EV64360 is not set
+CONFIG_TSI108_BRIDGE=y
+# CONFIG_WANT_EARLY_SERIAL is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SOFTWARE_SUSPEND is not set
+# CONFIG_SECCOMP is not set
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_GENERIC_ISA_DMA=y
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_INDIRECT_PCI is not set
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# PCI Hotplug Support
+#
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_NETDEBUG is not set
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+# CONFIG_MTD is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=131072
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+
+#
+# SCSI Transport Attributes
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_MEGARAID_SAS is not set
+CONFIG_SCSI_SATA=y
+# CONFIG_SCSI_SATA_AHCI is not set
+# CONFIG_SCSI_SATA_SVW is not set
+# CONFIG_SCSI_ATA_PIIX is not set
+CONFIG_SCSI_SATA_MV=y
+# CONFIG_SCSI_SATA_NV is not set
+# CONFIG_SCSI_PDC_ADMA is not set
+# CONFIG_SCSI_SATA_QSTOR is not set
+# CONFIG_SCSI_SATA_PROMISE is not set
+# CONFIG_SCSI_SATA_SX4 is not set
+# CONFIG_SCSI_SATA_SIL is not set
+# CONFIG_SCSI_SATA_SIL24 is not set
+# CONFIG_SCSI_SATA_SIS is not set
+# CONFIG_SCSI_SATA_ULI is not set
+# CONFIG_SCSI_SATA_VIA is not set
+# CONFIG_SCSI_SATA_VITESSE is not set
+# CONFIG_SCSI_BUSLOGIC is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_EATA is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_GDTH is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_SYM53C8XX_2 is not set
+# CONFIG_SCSI_IPR is not set
+# CONFIG_SCSI_QLOGIC_1280 is not set
+# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_LPFC is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_NSP32 is not set
+# CONFIG_SCSI_DEBUG is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+# CONFIG_FUSION_SPI is not set
+# CONFIG_FUSION_FC is not set
+# CONFIG_FUSION_SAS is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+
+#
+# Macintosh device drivers
+#
+# CONFIG_WINDFARM is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_NET_PCI=y
+# CONFIG_PCNET32 is not set
+# CONFIG_AMD8111_ETH is not set
+# CONFIG_ADAPTEC_STARFIRE is not set
+# CONFIG_B44 is not set
+# CONFIG_FORCEDETH is not set
+# CONFIG_DGRS is not set
+# CONFIG_EEPRO100 is not set
+CONFIG_E100=y
+# CONFIG_FEALNX is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NE2K_PCI is not set
+# CONFIG_8139CP is not set
+CONFIG_8139TOO=y
+# CONFIG_8139TOO_PIO is not set
+# CONFIG_8139TOO_TUNE_TWISTER is not set
+# CONFIG_8139TOO_8129 is not set
+# CONFIG_8139_OLD_RX_RESET is not set
+# CONFIG_SIS900 is not set
+# CONFIG_EPIC100 is not set
+# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
+# CONFIG_VIA_RHINE is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_TSI108_ETH=y
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_PCI=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Misc devices
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
+#
+
+#
+# Real Time Clock
+#
+# CONFIG_RTC_CLASS is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_DEBUG_KERNEL is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_DEBUG_FS is not set
+# CONFIG_UNWIND_INFO is not set
+# CONFIG_BOOTX_TEXT is not set
+# CONFIG_SERIAL_TEXT_DEBUG is not set
+# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
+# CONFIG_PPC_EARLY_DEBUG_G5 is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS is not set
+# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
+# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Hardware crypto devices
+#
^ permalink raw reply related
* [PATCH/2.6.17-rc6 3/4 v2]Powerpc: Add tsi108 mpic support
From: Zang Roy-r61911 @ 2006-06-13 7:07 UTC (permalink / raw)
To: Paul Mackerras, Benjamin Herrenschmidt
Cc: linuxppc-dev list, Alexandre.Bounine, Yang Xin-Xin-r48390
Add Tundra Semiconductor tsi108 host bridge interrupt
controller support (by modified mpic port).
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
---
diff --git a/arch/powerpc/sysdev/mpic.c b/arch/powerpc/sysdev/mpic.c
index 7dcdfcb..fc21e47 100644
--- a/arch/powerpc/sysdev/mpic.c
+++ b/arch/powerpc/sysdev/mpic.c
@@ -55,6 +55,78 @@ #define distribute_irqs (0)
#endif
#endif
+static struct mpic_info mpic_infos[] = {
+ [0] = { /* Original OpenPIC compatible MPIC */
+ .greg_base = MPIC_GREG_BASE,
+ .greg_frr0 = MPIC_GREG_FEATURE_0,
+ .greg_config0 = MPIC_GREG_GLOBAL_CONF_0,
+ .greg_vendor_id = MPIC_GREG_VENDOR_ID,
+ .greg_ipi_vp0 = MPIC_GREG_IPI_VECTOR_PRI_0,
+ .greg_ipi_stride = MPIC_GREG_IPI_STRIDE,
+ .greg_spurious = MPIC_GREG_SPURIOUS,
+ .greg_tfrr = MPIC_GREG_TIMER_FREQ,
+
+ .timer_base = MPIC_TIMER_BASE,
+ .timer_stride = MPIC_TIMER_STRIDE,
+ .timer_ccr = MPIC_TIMER_CURRENT_CNT,
+ .timer_bcr = MPIC_TIMER_BASE_CNT,
+ .timer_vpr = MPIC_TIMER_VECTOR_PRI,
+ .timer_dest = MPIC_TIMER_DESTINATION,
+
+ .cpu_base = MPIC_CPU_BASE,
+ .cpu_stride = MPIC_CPU_STRIDE,
+ .cpu_ipi_disp0 = MPIC_CPU_IPI_DISPATCH_0,
+ .cpu_ipi_disp_stride = MPIC_CPU_IPI_DISPATCH_STRIDE,
+ .cpu_task_pri = MPIC_CPU_CURRENT_TASK_PRI,
+ .cpu_whoami = MPIC_CPU_WHOAMI,
+ .cpu_intack = MPIC_CPU_INTACK,
+ .cpu_eoi = MPIC_CPU_EOI,
+
+ .irq_base = MPIC_IRQ_BASE,
+ .irq_stride = MPIC_IRQ_STRIDE,
+ .irq_vpr = MPIC_IRQ_VECTOR_PRI,
+ .irq_vpr_vector = MPIC_VECPRI_VECTOR_MASK,
+ .irq_vpr_polpos = MPIC_VECPRI_POLARITY_POSITIVE,
+ .irq_vpr_senlvl = MPIC_VECPRI_SENSE_LEVEL,
+ .irq_dest = MPIC_IRQ_DESTINATION,
+ },
+
+ [1] = { /* Tsi108/109 PIC */
+ .greg_base = TSI108_GREG_BASE,
+ .greg_frr0 = TSI108_GREG_FEATURE_0,
+ .greg_config0 = TSI108_GREG_GLOBAL_CONF_0,
+ .greg_vendor_id = TSI108_GREG_VENDOR_ID,
+ .greg_ipi_vp0 = TSI108_GREG_IPI_VECTOR_PRI_0,
+ .greg_ipi_stride = TSI108_GREG_IPI_STRIDE,
+ .greg_spurious = TSI108_GREG_SPURIOUS,
+ .greg_tfrr = TSI108_GREG_TIMER_FREQ,
+
+ .timer_base = TSI108_TIMER_BASE,
+ .timer_stride = TSI108_TIMER_STRIDE,
+ .timer_ccr = TSI108_TIMER_CURRENT_CNT,
+ .timer_bcr = TSI108_TIMER_BASE_CNT,
+ .timer_vpr = TSI108_TIMER_VECTOR_PRI,
+ .timer_dest = TSI108_TIMER_DESTINATION,
+
+ .cpu_base = TSI108_CPU_BASE,
+ .cpu_stride = TSI108_CPU_STRIDE,
+ .cpu_ipi_disp0 = TSI108_CPU_IPI_DISPATCH_0,
+ .cpu_ipi_disp_stride = TSI108_CPU_IPI_DISPATCH_STRIDE,
+ .cpu_task_pri = TSI108_CPU_CURRENT_TASK_PRI,
+ .cpu_whoami = 0xFFFFFFFF,
+ .cpu_intack = TSI108_CPU_INTACK,
+ .cpu_eoi = TSI108_CPU_EOI,
+
+ .irq_base = TSI108_IRQ_REG_BASE,
+ .irq_stride = TSI108_IRQ_STRIDE,
+ .irq_vpr = TSI108_IRQ_VECTOR_PRI,
+ .irq_vpr_vector = TSI108_VECPRI_VECTOR_MASK,
+ .irq_vpr_polpos = TSI108_VECPRI_POLARITY_POSITIVE,
+ .irq_vpr_senlvl = TSI108_VECPRI_SENSE_LEVEL,
+ .irq_dest = TSI108_IRQ_DESTINATION,
+ },
+};
+
/*
* Register accessor functions
*/
@@ -81,7 +153,8 @@ static inline void _mpic_write(unsigned
static inline u32 _mpic_ipi_read(struct mpic *mpic, unsigned int ipi)
{
unsigned int be = (mpic->flags & MPIC_BIG_ENDIAN) != 0;
- unsigned int offset = MPIC_GREG_IPI_VECTOR_PRI_0 + (ipi * 0x10);
+ unsigned int offset = mpic->hw_set->greg_ipi_vp0 +
+ (ipi * mpic->hw_set->greg_ipi_stride);
if (mpic->flags & MPIC_BROKEN_IPI)
be = !be;
@@ -90,7 +163,8 @@ static inline u32 _mpic_ipi_read(struct
static inline void _mpic_ipi_write(struct mpic *mpic, unsigned int ipi, u32 value)
{
- unsigned int offset = MPIC_GREG_IPI_VECTOR_PRI_0 + (ipi * 0x10);
+ unsigned int offset = mpic->hw_set->greg_ipi_vp0 +
+ (ipi * mpic->hw_set->greg_ipi_stride);
_mpic_write(mpic->flags & MPIC_BIG_ENDIAN, mpic->gregs, offset, value);
}
@@ -121,7 +195,7 @@ static inline u32 _mpic_irq_read(struct
unsigned int idx = src_no & mpic->isu_mask;
return _mpic_read(mpic->flags & MPIC_BIG_ENDIAN, mpic->isus[isu],
- reg + (idx * MPIC_IRQ_STRIDE));
+ reg + (idx * mpic->hw_set->irq_stride));
}
static inline void _mpic_irq_write(struct mpic *mpic, unsigned int src_no,
@@ -131,7 +205,7 @@ static inline void _mpic_irq_write(struc
unsigned int idx = src_no & mpic->isu_mask;
_mpic_write(mpic->flags & MPIC_BIG_ENDIAN, mpic->isus[isu],
- reg + (idx * MPIC_IRQ_STRIDE), value);
+ reg + (idx * mpic->hw_set->irq_stride), value);
}
#define mpic_read(b,r) _mpic_read(mpic->flags & MPIC_BIG_ENDIAN,(b),(r))
@@ -157,8 +231,8 @@ static void __init mpic_test_broken_ipi(
{
u32 r;
- mpic_write(mpic->gregs, MPIC_GREG_IPI_VECTOR_PRI_0, MPIC_VECPRI_MASK);
- r = mpic_read(mpic->gregs, MPIC_GREG_IPI_VECTOR_PRI_0);
+ mpic_write(mpic->gregs, mpic->hw_set->greg_ipi_vp0, MPIC_VECPRI_MASK);
+ r = mpic_read(mpic->gregs, mpic->hw_set->greg_ipi_vp0);
if (r == le32_to_cpu(MPIC_VECPRI_MASK)) {
printk(KERN_INFO "mpic: Detected reversed IPI registers\n");
@@ -392,8 +466,8 @@ static inline struct mpic * mpic_from_ir
/* Send an EOI */
static inline void mpic_eoi(struct mpic *mpic)
{
- mpic_cpu_write(MPIC_CPU_EOI, 0);
- (void)mpic_cpu_read(MPIC_CPU_WHOAMI);
+ mpic_cpu_write(mpic->hw_set->cpu_eoi, 0);
+ (void)mpic_cpu_read(mpic->hw_set->cpu_task_pri);
}
#ifdef CONFIG_SMP
@@ -419,8 +493,8 @@ static void mpic_enable_irq(unsigned int
DBG("%p: %s: enable_irq: %d (src %d)\n", mpic, mpic->name, irq, src);
- mpic_irq_write(src, MPIC_IRQ_VECTOR_PRI,
- mpic_irq_read(src, MPIC_IRQ_VECTOR_PRI) &
+ mpic_irq_write(src, mpic->hw_set->irq_vpr,
+ mpic_irq_read(src, mpic->hw_set->irq_vpr) &
~MPIC_VECPRI_MASK);
/* make sure mask gets to controller before we return to user */
@@ -429,7 +503,7 @@ static void mpic_enable_irq(unsigned int
printk(KERN_ERR "mpic_enable_irq timeout\n");
break;
}
- } while(mpic_irq_read(src, MPIC_IRQ_VECTOR_PRI) & MPIC_VECPRI_MASK);
+ } while(mpic_irq_read(src, mpic->hw_set->irq_vpr) & MPIC_VECPRI_MASK);
#ifdef CONFIG_MPIC_BROKEN_U3
if (mpic->flags & MPIC_BROKEN_U3) {
@@ -466,8 +540,8 @@ static void mpic_disable_irq(unsigned in
DBG("%s: disable_irq: %d (src %d)\n", mpic->name, irq, src);
- mpic_irq_write(src, MPIC_IRQ_VECTOR_PRI,
- mpic_irq_read(src, MPIC_IRQ_VECTOR_PRI) |
+ mpic_irq_write(src, mpic->hw_set->irq_vpr,
+ mpic_irq_read(src, mpic->hw_set->irq_vpr) |
MPIC_VECPRI_MASK);
/* make sure mask gets to controller before we return to user */
@@ -476,7 +550,7 @@ static void mpic_disable_irq(unsigned in
printk(KERN_ERR "mpic_enable_irq timeout\n");
break;
}
- } while(!(mpic_irq_read(src, MPIC_IRQ_VECTOR_PRI) & MPIC_VECPRI_MASK));
+ } while(!(mpic_irq_read(src, mpic->hw_set->irq_vpr) & MPIC_VECPRI_MASK));
}
static void mpic_shutdown_irq(unsigned int irq)
@@ -557,7 +631,7 @@ static void mpic_set_affinity(unsigned i
cpus_and(tmp, cpumask, cpu_online_map);
- mpic_irq_write(irq - mpic->irq_offset, MPIC_IRQ_DESTINATION,
+ mpic_irq_write(irq - mpic->irq_offset, mpic->hw_set->irq_dest,
mpic_physmask(cpus_addr(tmp)[0]));
}
@@ -613,18 +687,20 @@ #endif /* CONFIG_SMP */
mpic->num_sources = 0; /* so far */
mpic->senses = senses;
mpic->senses_count = senses_count;
+ mpic->hw_set = &mpic_infos[MPIC_GET_MOD_ID(flags)];
/* Map the global registers */
- mpic->gregs = ioremap(phys_addr + MPIC_GREG_BASE, 0x1000);
- mpic->tmregs = mpic->gregs + ((MPIC_TIMER_BASE - MPIC_GREG_BASE) >> 2);
+ mpic->gregs = ioremap(phys_addr + mpic->hw_set->greg_base, 0x1000);
+ mpic->tmregs = mpic->gregs +
+ ((mpic->hw_set->timer_base - mpic->hw_set->greg_base) >> 2);
BUG_ON(mpic->gregs == NULL);
/* Reset */
if (flags & MPIC_WANTS_RESET) {
- mpic_write(mpic->gregs, MPIC_GREG_GLOBAL_CONF_0,
- mpic_read(mpic->gregs, MPIC_GREG_GLOBAL_CONF_0)
+ mpic_write(mpic->gregs, mpic->hw_set->greg_config0,
+ mpic_read(mpic->gregs, mpic->hw_set->greg_config0)
| MPIC_GREG_GCONF_RESET);
- while( mpic_read(mpic->gregs, MPIC_GREG_GLOBAL_CONF_0)
+ while( mpic_read(mpic->gregs, mpic->hw_set->greg_config0)
& MPIC_GREG_GCONF_RESET)
mb();
}
@@ -633,7 +709,7 @@ #endif /* CONFIG_SMP */
* MPICs, num sources as well. On ISU MPICs, sources are counted
* as ISUs are added
*/
- reg = mpic_read(mpic->gregs, MPIC_GREG_FEATURE_0);
+ reg = mpic_read(mpic->gregs, mpic->hw_set->greg_frr0);
mpic->num_cpus = ((reg & MPIC_GREG_FEATURE_LAST_CPU_MASK)
>> MPIC_GREG_FEATURE_LAST_CPU_SHIFT) + 1;
if (isu_size == 0)
@@ -642,16 +718,16 @@ #endif /* CONFIG_SMP */
/* Map the per-CPU registers */
for (i = 0; i < mpic->num_cpus; i++) {
- mpic->cpuregs[i] = ioremap(phys_addr + MPIC_CPU_BASE +
- i * MPIC_CPU_STRIDE, 0x1000);
+ mpic->cpuregs[i] = ioremap(phys_addr + mpic->hw_set->cpu_base +
+ i * mpic->hw_set->cpu_stride, 0x1000);
BUG_ON(mpic->cpuregs[i] == NULL);
}
/* Initialize main ISU if none provided */
if (mpic->isu_size == 0) {
mpic->isu_size = mpic->num_sources;
- mpic->isus[0] = ioremap(phys_addr + MPIC_IRQ_BASE,
- MPIC_IRQ_STRIDE * mpic->isu_size);
+ mpic->isus[0] = ioremap(phys_addr + mpic->hw_set->irq_base,
+ mpic->hw_set->irq_stride * mpic->isu_size);
BUG_ON(mpic->isus[0] == NULL);
}
mpic->isu_shift = 1 + __ilog2(mpic->isu_size - 1);
@@ -693,7 +769,8 @@ void __init mpic_assign_isu(struct mpic
BUG_ON(isu_num >= MPIC_MAX_ISU);
- mpic->isus[isu_num] = ioremap(phys_addr, MPIC_IRQ_STRIDE * mpic->isu_size);
+ mpic->isus[isu_num] = ioremap(phys_addr,
+ mpic->hw_set->irq_stride * mpic->isu_size);
if ((isu_first + mpic->isu_size) > mpic->num_sources)
mpic->num_sources = isu_first + mpic->isu_size;
}
@@ -729,14 +806,15 @@ void __init mpic_init(struct mpic *mpic)
printk(KERN_INFO "mpic: Initializing for %d sources\n", mpic->num_sources);
/* Set current processor priority to max */
- mpic_cpu_write(MPIC_CPU_CURRENT_TASK_PRI, 0xf);
+ mpic_cpu_write(mpic->hw_set->cpu_task_pri, 0xf);
/* Initialize timers: just disable them all */
for (i = 0; i < 4; i++) {
mpic_write(mpic->tmregs,
- i * MPIC_TIMER_STRIDE + MPIC_TIMER_DESTINATION, 0);
+ i * mpic->hw_set->timer_stride +
+ mpic->hw_set->timer_dest, 0);
mpic_write(mpic->tmregs,
- i * MPIC_TIMER_STRIDE + MPIC_TIMER_VECTOR_PRI,
+ i * mpic->hw_set->timer_stride + mpic->hw_set->timer_vpr,
MPIC_VECPRI_MASK |
(MPIC_VEC_TIMER_0 + i));
}
@@ -780,14 +858,14 @@ #endif /* CONFIG_MPIC_BROKEN_U3 */
/* do senses munging */
if (mpic->senses && i < mpic->senses_count) {
if (mpic->senses[i] & IRQ_SENSE_LEVEL)
- vecpri |= MPIC_VECPRI_SENSE_LEVEL;
+ vecpri |= mpic->hw_set->irq_vpr_senlvl;
if (mpic->senses[i] & IRQ_POLARITY_POSITIVE)
- vecpri |= MPIC_VECPRI_POLARITY_POSITIVE;
+ vecpri |= mpic->hw_set->irq_vpr_polpos;
} else
- vecpri |= MPIC_VECPRI_SENSE_LEVEL;
+ vecpri |= mpic->hw_set->irq_vpr_senlvl;
/* remember if it was a level interrupts */
- level = (vecpri & MPIC_VECPRI_SENSE_LEVEL);
+ level = (vecpri & mpic->hw_set->irq_vpr_senlvl);
/* deal with broken U3 */
if (mpic->flags & MPIC_BROKEN_U3) {
@@ -795,7 +873,7 @@ #ifdef CONFIG_MPIC_BROKEN_U3
if (mpic_is_ht_interrupt(mpic, i)) {
vecpri &= ~(MPIC_VECPRI_SENSE_MASK |
MPIC_VECPRI_POLARITY_MASK);
- vecpri |= MPIC_VECPRI_POLARITY_POSITIVE;
+ vecpri |= mpic->hw_set->irq_vpr_polpos;
}
#else
printk(KERN_ERR "mpic: BROKEN_U3 set, but CONFIG doesn't match\n");
@@ -806,8 +884,8 @@ #endif
(level != 0));
/* init hw */
- mpic_irq_write(i, MPIC_IRQ_VECTOR_PRI, vecpri);
- mpic_irq_write(i, MPIC_IRQ_DESTINATION,
+ mpic_irq_write(i, mpic->hw_set->irq_vpr, vecpri);
+ mpic_irq_write(i, mpic->hw_set->irq_dest,
1 << hard_smp_processor_id());
/* init linux descriptors */
@@ -818,15 +896,16 @@ #endif
}
/* Init spurrious vector */
- mpic_write(mpic->gregs, MPIC_GREG_SPURIOUS, MPIC_VEC_SPURRIOUS);
+ mpic_write(mpic->gregs, mpic->hw_set->greg_spurious, MPIC_VEC_SPURRIOUS);
- /* Disable 8259 passthrough */
- mpic_write(mpic->gregs, MPIC_GREG_GLOBAL_CONF_0,
- mpic_read(mpic->gregs, MPIC_GREG_GLOBAL_CONF_0)
- | MPIC_GREG_GCONF_8259_PTHROU_DIS);
+ /* Disable 8259 passthrough, if supported */
+ if (MPIC_GET_MOD_ID(mpic->flags) != MPIC_ID_TSI108)
+ mpic_write(mpic->gregs, mpic->hw_set->greg_config0,
+ mpic_read(mpic->gregs, mpic->hw_set->greg_config0)
+ | MPIC_GREG_GCONF_8259_PTHROU_DIS);
/* Set current processor priority to 0 */
- mpic_cpu_write(MPIC_CPU_CURRENT_TASK_PRI, 0);
+ mpic_cpu_write(mpic->hw_set->cpu_task_pri, 0);
}
@@ -845,9 +924,9 @@ void mpic_irq_set_priority(unsigned int
mpic_ipi_write(irq - mpic->ipi_offset,
reg | (pri << MPIC_VECPRI_PRIORITY_SHIFT));
} else {
- reg = mpic_irq_read(irq - mpic->irq_offset,MPIC_IRQ_VECTOR_PRI)
+ reg = mpic_irq_read(irq - mpic->irq_offset,mpic->hw_set->irq_vpr)
& ~MPIC_VECPRI_PRIORITY_MASK;
- mpic_irq_write(irq - mpic->irq_offset, MPIC_IRQ_VECTOR_PRI,
+ mpic_irq_write(irq - mpic->irq_offset, mpic->hw_set->irq_vpr,
reg | (pri << MPIC_VECPRI_PRIORITY_SHIFT));
}
spin_unlock_irqrestore(&mpic_lock, flags);
@@ -864,7 +943,7 @@ unsigned int mpic_irq_get_priority(unsig
if (is_ipi)
reg = mpic_ipi_read(irq - mpic->ipi_offset);
else
- reg = mpic_irq_read(irq - mpic->irq_offset, MPIC_IRQ_VECTOR_PRI);
+ reg = mpic_irq_read(irq - mpic->irq_offset, mpic->hw_set->irq_vpr);
spin_unlock_irqrestore(&mpic_lock, flags);
return (reg & MPIC_VECPRI_PRIORITY_MASK) >> MPIC_VECPRI_PRIORITY_SHIFT;
}
@@ -890,12 +969,12 @@ #ifdef CONFIG_SMP
*/
if (distribute_irqs) {
for (i = 0; i < mpic->num_sources ; i++)
- mpic_irq_write(i, MPIC_IRQ_DESTINATION,
- mpic_irq_read(i, MPIC_IRQ_DESTINATION) | msk);
+ mpic_irq_write(i, mpic->hw_set->irq_dest,
+ mpic_irq_read(i, mpic->hw_set->irq_dest) | msk);
}
/* Set current processor priority to 0 */
- mpic_cpu_write(MPIC_CPU_CURRENT_TASK_PRI, 0);
+ mpic_cpu_write(mpic->hw_set->cpu_task_pri, 0);
spin_unlock_irqrestore(&mpic_lock, flags);
#endif /* CONFIG_SMP */
@@ -905,7 +984,7 @@ int mpic_cpu_get_priority(void)
{
struct mpic *mpic = mpic_primary;
- return mpic_cpu_read(MPIC_CPU_CURRENT_TASK_PRI);
+ return mpic_cpu_read(mpic->hw_set->cpu_task_pri);
}
void mpic_cpu_set_priority(int prio)
@@ -913,7 +992,7 @@ void mpic_cpu_set_priority(int prio)
struct mpic *mpic = mpic_primary;
prio &= MPIC_CPU_TASKPRI_MASK;
- mpic_cpu_write(MPIC_CPU_CURRENT_TASK_PRI, prio);
+ mpic_cpu_write(mpic->hw_set->cpu_task_pri, prio);
}
/*
@@ -935,11 +1014,11 @@ void mpic_teardown_this_cpu(int secondar
/* let the mpic know we don't want intrs. */
for (i = 0; i < mpic->num_sources ; i++)
- mpic_irq_write(i, MPIC_IRQ_DESTINATION,
- mpic_irq_read(i, MPIC_IRQ_DESTINATION) & ~msk);
+ mpic_irq_write(i, mpic->hw_set->irq_dest,
+ mpic_irq_read(i, mpic->hw_set->irq_dest) & ~msk);
/* Set current processor priority to max */
- mpic_cpu_write(MPIC_CPU_CURRENT_TASK_PRI, 0xf);
+ mpic_cpu_write(mpic->hw_set->cpu_task_pri, 0xf);
spin_unlock_irqrestore(&mpic_lock, flags);
}
@@ -955,7 +1034,8 @@ #ifdef DEBUG_IPI
DBG("%s: send_ipi(ipi_no: %d)\n", mpic->name, ipi_no);
#endif
- mpic_cpu_write(MPIC_CPU_IPI_DISPATCH_0 + ipi_no * 0x10,
+ mpic_cpu_write(mpic->hw_set->cpu_ipi_disp0 +
+ ipi_no * mpic->hw_set->cpu_ipi_disp_stride,
mpic_physmask(cpu_mask & cpus_addr(cpu_online_map)[0]));
}
@@ -963,7 +1043,7 @@ int mpic_get_one_irq(struct mpic *mpic,
{
u32 irq;
- irq = mpic_cpu_read(MPIC_CPU_INTACK) & MPIC_VECPRI_VECTOR_MASK;
+ irq = mpic_cpu_read(mpic->hw_set->cpu_intack) & mpic->hw_set->irq_vpr_vector;
#ifdef DEBUG_LOW
DBG("%s: get_one_irq(): %d\n", mpic->name, irq);
#endif
@@ -972,11 +1052,17 @@ #ifdef DEBUG_LOW
DBG("%s: cascading ...\n", mpic->name);
#endif
irq = mpic->cascade(regs, mpic->cascade_data);
+#ifdef DEBUG_LOW
+ DBG("%s: cascaded irq: %d\n", mpic->name, irq);
+#endif
mpic_eoi(mpic);
return irq;
}
- if (unlikely(irq == MPIC_VEC_SPURRIOUS))
+ if (unlikely(irq == MPIC_VEC_SPURRIOUS)) {
+ if (mpic->flags & MPIC_SPV_EOI)
+ mpic_eoi(mpic);
return -1;
+ }
if (irq < MPIC_VEC_IPI_0) {
#ifdef DEBUG_IRQ
DBG("%s: irq %d\n", mpic->name, irq + mpic->irq_offset);
diff --git a/include/asm-powerpc/mpic.h b/include/asm-powerpc/mpic.h
index 6b9e781..72131a4 100644
--- a/include/asm-powerpc/mpic.h
+++ b/include/asm-powerpc/mpic.h
@@ -37,6 +37,7 @@ #define MPIC_GREG_IPI_VECTOR_PRI_0 0x000
#define MPIC_GREG_IPI_VECTOR_PRI_1 0x000b0
#define MPIC_GREG_IPI_VECTOR_PRI_2 0x000c0
#define MPIC_GREG_IPI_VECTOR_PRI_3 0x000d0
+#define MPIC_GREG_IPI_STRIDE 0x10
#define MPIC_GREG_SPURIOUS 0x000e0
#define MPIC_GREG_TIMER_FREQ 0x000f0
@@ -64,6 +65,7 @@ #define MPIC_CPU_IPI_DISPATCH_0 0x00040
#define MPIC_CPU_IPI_DISPATCH_1 0x00050
#define MPIC_CPU_IPI_DISPATCH_2 0x00060
#define MPIC_CPU_IPI_DISPATCH_3 0x00070
+#define MPIC_CPU_IPI_DISPATCH_STRIDE 0x00010
#define MPIC_CPU_CURRENT_TASK_PRI 0x00080
#define MPIC_CPU_TASKPRI_MASK 0x0000000f
#define MPIC_CPU_WHOAMI 0x00090
@@ -91,6 +93,55 @@ #define MPIC_VECPRI_SENSE_EDGE 0x0000
#define MPIC_VECPRI_SENSE_MASK 0x00400000
#define MPIC_IRQ_DESTINATION 0x00010
+/******************************************************************************
+ * Tsi108 implementation of MPIC has many differences form the original one
+ */
+
+/*
+ * Global registers
+ */
+
+#define TSI108_GREG_BASE 0x00000
+#define TSI108_GREG_FEATURE_0 0x00000
+#define TSI108_GREG_GLOBAL_CONF_0 0x00004
+#define TSI108_GREG_VENDOR_ID 0x0000c
+#define TSI108_GREG_IPI_VECTOR_PRI_0 0x00204 /* Doorbell 0 */
+#define TSI108_GREG_IPI_STRIDE 0x0c
+#define TSI108_GREG_SPURIOUS 0x00010
+#define TSI108_GREG_TIMER_FREQ 0x00014
+
+/*
+ * Timer registers
+ */
+#define TSI108_TIMER_BASE 0x0030
+#define TSI108_TIMER_STRIDE 0x10
+#define TSI108_TIMER_CURRENT_CNT 0x00000
+#define TSI108_TIMER_BASE_CNT 0x00004
+#define TSI108_TIMER_VECTOR_PRI 0x00008
+#define TSI108_TIMER_DESTINATION 0x0000c
+
+/*
+ * Per-Processor registers
+ */
+#define TSI108_CPU_BASE 0x00300
+#define TSI108_CPU_STRIDE 0x00040
+#define TSI108_CPU_IPI_DISPATCH_0 0x00200
+#define TSI108_CPU_IPI_DISPATCH_STRIDE 0x00000
+#define TSI108_CPU_CURRENT_TASK_PRI 0x00000
+#define TSI108_CPU_INTACK 0x00004
+#define TSI108_CPU_EOI 0x00008
+
+/*
+ * Per-source registers
+ */
+#define TSI108_IRQ_REG_BASE 0x00100
+#define TSI108_IRQ_STRIDE 0x00008
+#define TSI108_IRQ_VECTOR_PRI 0x00000
+#define TSI108_VECPRI_VECTOR_MASK 0x000000ff
+#define TSI108_VECPRI_POLARITY_POSITIVE 0x01000000
+#define TSI108_VECPRI_SENSE_LEVEL 0x02000000
+#define TSI108_IRQ_DESTINATION 0x00004
+
#define MPIC_MAX_IRQ_SOURCES 2048
#define MPIC_MAX_CPUS 32
#define MPIC_MAX_ISU 32
@@ -124,6 +175,40 @@ struct mpic_irq_fixup
};
#endif /* CONFIG_MPIC_BROKEN_U3 */
+struct mpic_info {
+ u32 greg_base; /* offset of global registers from MPIC base */
+ u32 greg_frr0; /* FRR0 offset from base */
+ u32 greg_config0; /* Global Config register offset from base */
+ u32 greg_vendor_id; /* VID register offset from base */
+ u32 greg_ipi_vp0; /* IPI Vector/Priority Registers */
+ u32 greg_ipi_stride; /* IPI Vector/Priority Registers spacing */
+ u32 greg_spurious; /* Spurious Vector Register */
+ u32 greg_tfrr; /* Global Timer Frequency Reporting Register */
+
+ u32 timer_base; /* Global Timer Registers base */
+ u32 timer_stride; /* Global Timer Registers spacing */
+ u32 timer_ccr; /* Global Timer Current Count Register */
+ u32 timer_bcr; /* Global Timer Base Count Register */
+ u32 timer_vpr; /* Global Timer Vector/Priority Register */
+ u32 timer_dest; /* Global Timer Destination Register */
+
+ u32 cpu_base; /* Global Timer Destination Register */
+ u32 cpu_stride; /* Global Timer Destination Register */
+ u32 cpu_ipi_disp0; /* IPI 0 Dispatch Command Register */
+ u32 cpu_ipi_disp_stride; /* IPI Dispatch spacing */
+ u32 cpu_task_pri; /* Processor Current Task Priority Register */
+ u32 cpu_whoami; /* Who Am I Register */
+ u32 cpu_intack; /* Interrupt Acknowledge Register */
+ u32 cpu_eoi; /* End of Interrupt Register */
+
+ u32 irq_base; /* Interrupt registers base */
+ u32 irq_stride; /* Interrupt registers spacing */
+ u32 irq_vpr; /* Interrupt Vector/Priority Register */
+ u32 irq_vpr_vector; /* Interrupt Vector Mask */
+ u32 irq_vpr_polpos; /* Interrupt Positive Polarity bit */
+ u32 irq_vpr_senlvl; /* Interrupt Level Sense bit */
+ u32 irq_dest; /* Interrupt Destination Register */
+};
/* The instance data of a given MPIC */
struct mpic
@@ -168,6 +253,8 @@ #endif
volatile u32 __iomem *tmregs;
volatile u32 __iomem *cpuregs[MPIC_MAX_CPUS];
volatile u32 __iomem *isus[MPIC_MAX_ISU];
+ /* Pointer to HW info structure */
+ struct mpic_info *hw_set;
/* link */
struct mpic *next;
@@ -186,6 +273,14 @@ #define MPIC_BROKEN_U3 0x00000004
#define MPIC_BROKEN_IPI 0x00000008
/* MPIC wants a reset */
#define MPIC_WANTS_RESET 0x00000010
+/* Spurious vector requires EOI */
+#define MPIC_SPV_EOI 0x00000020
+/* MPIC HW modification ID */
+#define MPIC_MOD_ID_MASK 0x00000f00
+#define MPIC_MOD_ID(val) (((val) << 8) & MPIC_MOD_ID_MASK)
+#define MPIC_GET_MOD_ID(flags) (((flags) & MPIC_MOD_ID_MASK) >> 8)
+#define MPIC_ID_MPIC 0 /* Original MPIC */
+#define MPIC_ID_TSI108 1 /* Tsi108/109 PIC */
/* Allocate the controller structure and setup the linux irq descs
* for the range if interrupts passed in. No HW initialization is
diff --git a/include/asm-powerpc/tsi108_irq.h b/include/asm-powerpc/tsi108_irq.h
new file mode 100644
index 0000000..4d725ed
--- /dev/null
+++ b/include/asm-powerpc/tsi108_irq.h
@@ -0,0 +1,124 @@
+/*
+ * (C) Copyright 2005 Tundra Semiconductor Corp.
+ * Alex Bounine, <alexandreb@tundra.com).
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * asm-ppc/tsi108_irq.h - definitions for interrupt controller
+ * initialization and external interrupt demultiplexing on TSI108EMU/SVB boards.
+ */
+
+#ifndef _ASM_PPC_TSI108_IRQ_H
+#define _ASM_PPC_TSI108_IRQ_H
+
+/*
+ * Tsi108 interrupts
+ */
+#ifndef TSI108_IRQ_BASE
+#define TSI108_IRQ_BASE 0
+#endif
+
+#define TSI108_IRQ(x) (TSI108_IRQ_BASE + (x))
+
+#define TSI108_MAX_VECTORS (36 + 4) /* 36 sources + PCI INT demux */
+#define MAX_TASK_PRIO 0xF
+
+#define TSI108_IRQ_SPURIOUS (TSI108_MAX_VECTORS)
+
+#define DEFAULT_PRIO_LVL 10 /* initial priority level */
+
+/* Interrupt vectors assignment to external and internal
+ * sources of requests. */
+
+/* EXTERNAL INTERRUPT SOURCES */
+
+#define IRQ_TSI108_EXT_INT0 TSI108_IRQ(0) /* External Source at INT[0] */
+#define IRQ_TSI108_EXT_INT1 TSI108_IRQ(1) /* External Source at INT[1] */
+#define IRQ_TSI108_EXT_INT2 TSI108_IRQ(2) /* External Source at INT[2] */
+#define IRQ_TSI108_EXT_INT3 TSI108_IRQ(3) /* External Source at INT[3] */
+
+/* INTERNAL INTERRUPT SOURCES */
+
+#define IRQ_TSI108_RESERVED0 TSI108_IRQ(4) /* Reserved IRQ */
+#define IRQ_TSI108_RESERVED1 TSI108_IRQ(5) /* Reserved IRQ */
+#define IRQ_TSI108_RESERVED2 TSI108_IRQ(6) /* Reserved IRQ */
+#define IRQ_TSI108_RESERVED3 TSI108_IRQ(7) /* Reserved IRQ */
+#define IRQ_TSI108_DMA0 TSI108_IRQ(8) /* DMA0 */
+#define IRQ_TSI108_DMA1 TSI108_IRQ(9) /* DMA1 */
+#define IRQ_TSI108_DMA2 TSI108_IRQ(10) /* DMA2 */
+#define IRQ_TSI108_DMA3 TSI108_IRQ(11) /* DMA3 */
+#define IRQ_TSI108_UART0 TSI108_IRQ(12) /* UART0 */
+#define IRQ_TSI108_UART1 TSI108_IRQ(13) /* UART1 */
+#define IRQ_TSI108_I2C TSI108_IRQ(14) /* I2C */
+#define IRQ_TSI108_GPIO TSI108_IRQ(15) /* GPIO */
+#define IRQ_TSI108_GIGE0 TSI108_IRQ(16) /* GIGE0 */
+#define IRQ_TSI108_GIGE1 TSI108_IRQ(17) /* GIGE1 */
+#define IRQ_TSI108_RESERVED4 TSI108_IRQ(18) /* Reserved IRQ */
+#define IRQ_TSI108_HLP TSI108_IRQ(19) /* HLP */
+#define IRQ_TSI108_SDRAM TSI108_IRQ(20) /* SDC */
+#define IRQ_TSI108_PROC_IF TSI108_IRQ(21) /* Processor IF */
+#define IRQ_TSI108_RESERVED5 TSI108_IRQ(22) /* Reserved IRQ */
+#define IRQ_TSI108_PCI TSI108_IRQ(23) /* PCI/X block */
+
+#define IRQ_TSI108_MBOX0 TSI108_IRQ(24) /* Mailbox 0 register */
+#define IRQ_TSI108_MBOX1 TSI108_IRQ(25) /* Mailbox 1 register */
+#define IRQ_TSI108_MBOX2 TSI108_IRQ(26) /* Mailbox 2 register */
+#define IRQ_TSI108_MBOX3 TSI108_IRQ(27) /* Mailbox 3 register */
+
+#define IRQ_TSI108_DBELL0 TSI108_IRQ(28) /* Doorbell 0 */
+#define IRQ_TSI108_DBELL1 TSI108_IRQ(29) /* Doorbell 1 */
+#define IRQ_TSI108_DBELL2 TSI108_IRQ(30) /* Doorbell 2 */
+#define IRQ_TSI108_DBELL3 TSI108_IRQ(31) /* Doorbell 3 */
+
+#define IRQ_TSI108_TIMER0 TSI108_IRQ(32) /* Global Timer 0 */
+#define IRQ_TSI108_TIMER1 TSI108_IRQ(33) /* Global Timer 1 */
+#define IRQ_TSI108_TIMER2 TSI108_IRQ(34) /* Global Timer 2 */
+#define IRQ_TSI108_TIMER3 TSI108_IRQ(35) /* Global Timer 3 */
+
+/*
+ * PCI bus INTA# - INTD# lines demultiplexor
+ */
+#define IRQ_PCI_INTAD_BASE TSI108_IRQ(36)
+#define IRQ_PCI_INTA (IRQ_PCI_INTAD_BASE + 0)
+#define IRQ_PCI_INTB (IRQ_PCI_INTAD_BASE + 1)
+#define IRQ_PCI_INTC (IRQ_PCI_INTAD_BASE + 2)
+#define IRQ_PCI_INTD (IRQ_PCI_INTAD_BASE + 3)
+#define NUM_PCI_IRQS (4)
+
+/* number of entries in vector dispatch table */
+#define IRQ_TSI108_TAB_SIZE (TSI108_MAX_VECTORS + 1)
+
+/* Mapping of MPIC outputs to processors' interrupt pins */
+
+#define IDIR_INT_OUT0 0x1
+#define IDIR_INT_OUT1 0x2
+#define IDIR_INT_OUT2 0x4
+#define IDIR_INT_OUT3 0x8
+
+/*---------------------------------------------------------------
+ * IRQ line configuration parameters */
+
+/* Interrupt delivery modes */
+typedef enum {
+ TSI108_IRQ_DIRECTED,
+ TSI108_IRQ_DISTRIBUTED,
+} TSI108_IRQ_MODE;
+#endif /* _ASM_PPC_TSI108_IRQ_H */
^ permalink raw reply related
* [PATCH/2.6.17-rc6 2/4 v2] Powerpc: Add tsi108 pci and platform d evice data register function
From: Zang Roy-r61911 @ 2006-06-13 7:07 UTC (permalink / raw)
To: Paul Mackerras, Benjamin Herrenschmidt
Cc: linuxppc-dev list, Alexandre.Bounine, Yang Xin-Xin-r48390
Add Tundra Semiconductor tsi108 pci and platform device data register function support.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
---
diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile
index 4c2b356..ad2da20 100644
--- a/arch/powerpc/sysdev/Makefile
+++ b/arch/powerpc/sysdev/Makefile
@@ -8,3 +8,4 @@ obj-$(CONFIG_U3_DART) += dart_iommu.o
obj-$(CONFIG_MMIO_NVRAM) += mmio_nvram.o
obj-$(CONFIG_PPC_83xx) += ipic.o
obj-$(CONFIG_FSL_SOC) += fsl_soc.o
+obj-$(CONFIG_TSI108_BRIDGE) += tsi108_pci.o tsi108_dev.o
diff --git a/arch/powerpc/sysdev/tsi108_dev.c b/arch/powerpc/sysdev/tsi108_dev.c
new file mode 100644
index 0000000..a56c6f9
--- /dev/null
+++ b/arch/powerpc/sysdev/tsi108_dev.c
@@ -0,0 +1,145 @@
+/*
+ * tsi108/109 device setup code
+ *
+ * Maintained by Roy Zang < tie-fei.zang@freescale.com >
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/major.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <asm/tsi108.h>
+
+#include <asm/system.h>
+#include <asm/atomic.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/prom.h>
+#include <mm/mmu_decl.h>
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(fmt...) do { printk(fmt); } while(0)
+#else
+#define DBG(fmt...) do { } while(0)
+#endif
+
+static phys_addr_t tsi108_csr_base = -1;
+
+phys_addr_t get_csrbase(void)
+{
+ struct device_node *tsi;
+
+ if (tsi108_csr_base != -1)
+ return tsi108_csr_base;
+
+ tsi = of_find_node_by_type(NULL, "tsi-bridge");
+ if (tsi) {
+ unsigned int size;
+ void *prop = get_property(tsi, "reg", &size);
+ tsi108_csr_base = of_translate_address(tsi, prop);
+ of_node_put(tsi);
+ };
+ return tsi108_csr_base;
+}
+
+u32 get_vir_csrbase(void)
+{
+ return (u32) (ioremap(get_csrbase(), 0x10000));
+}
+
+EXPORT_SYMBOL(get_csrbase);
+EXPORT_SYMBOL(get_vir_csrbase);
+
+static int __init tsi108_eth_of_init(void)
+{
+ struct device_node *np;
+ unsigned int i;
+ struct platform_device *tsi_eth_dev;
+ struct resource res;
+ int ret;
+
+ for (np = NULL, i = 0;
+ (np = of_find_compatible_node(np, "network", "tsi-ethernet")) != NULL;
+ i++) {
+ struct resource r[2];
+ struct device_node *phy;
+ hw_info tsi_eth_data;
+ unsigned int *id;
+ unsigned int *phy_id;
+ void *mac_addr;
+ phandle *ph;
+
+ memset(r, 0, sizeof(r));
+ memset(&tsi_eth_data, 0, sizeof(tsi_eth_data));
+
+ ret = of_address_to_resource(np, 0, &r[0]);
+ DBG("%s: name:start->end = %s:0x%lx-> 0x%lx\n",
+ __FUNCTION__,r[0].name, r[0].start, r[0].end);
+ if (ret)
+ goto err;
+
+ r[1].name = "tx";
+ r[1].start = np->intrs[0].line;
+ r[1].end = np->intrs[0].line;
+ r[1].flags = IORESOURCE_IRQ;
+
+ tsi_eth_dev =
+ platform_device_register_simple("tsi-ethernet", i, &r[0],
+ np->n_intrs + 1);
+
+ if (IS_ERR(tsi_eth_dev)) {
+ ret = PTR_ERR(tsi_eth_dev);
+ goto err;
+ }
+
+ mac_addr = get_property(np, "address", NULL);
+ memcpy(tsi_eth_data.mac_addr, mac_addr, 6);
+
+ ph = (phandle *) get_property(np, "phy-handle", NULL);
+ phy = of_find_node_by_phandle(*ph);
+
+ if (phy == NULL) {
+ ret = -ENODEV;
+ goto unreg;
+ }
+
+ id = (u32 *) get_property(phy, "reg", NULL);
+ phy_id = (u32 *) get_property(phy, "phy-id", NULL);
+ ret = of_address_to_resource(phy, 0, &res);
+ if (ret) {
+ of_node_put(phy);
+ goto unreg;
+ }
+ tsi_eth_data.regs = r[0].start;
+ tsi_eth_data.phyregs = res.start;
+ tsi_eth_data.phy = *phy_id;
+ tsi_eth_data.irq_num = np->intrs[0].line;
+ of_node_put(phy);
+ ret =
+ platform_device_add_data(tsi_eth_dev, &tsi_eth_data,
+ sizeof(hw_info));
+ if (ret)
+ goto unreg;
+ }
+ return 0;
+unreg:
+ platform_device_unregister(tsi_eth_dev);
+err:
+ return ret;
+}
+
+arch_initcall(tsi108_eth_of_init);
diff --git a/arch/powerpc/sysdev/tsi108_pci.c b/arch/powerpc/sysdev/tsi108_pci.c
new file mode 100644
index 0000000..f43d181
--- /dev/null
+++ b/arch/powerpc/sysdev/tsi108_pci.c
@@ -0,0 +1,412 @@
+/*
+ * Common routines for Tundra Semiconductor TSI108 host bridge.
+ *
+ * 2004-2005 (c) Tundra Semiconductor Corp.
+ * Author: Alex Bounine (alexandreb@tundra.com)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/slab.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+
+
+#include <asm/byteorder.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <asm/tsi108.h>
+#include <asm/tsi108_irq.h>
+#include <asm/prom.h>
+
+#undef DEBUG
+#ifdef DEBUG
+#define DBG(x...) printk(x)
+#else
+#define DBG(x...)
+#endif
+
+#define tsi_mk_config_addr(bus, devfunc, offset) \
+ ((((bus)<<16) | ((devfunc)<<8) | (offset & 0xfc)) + tsi108_pci_cfg_base)
+
+u32 tsi108_pci_cfg_base;
+u32 tsi108_csr_vir_base;
+
+extern u32 get_vir_csrbase(void);
+extern u32 tsi108_read_reg(u32 reg_offset);
+extern void tsi108_write_reg(u32 reg_offset, u32 val);
+
+int
+tsi108_direct_write_config(struct pci_bus *bus, unsigned int devfunc,
+ int offset, int len, u32 val)
+{
+ volatile unsigned char *cfg_addr;
+
+ if (ppc_md.pci_exclude_device)
+ if (ppc_md.pci_exclude_device(bus->number, devfunc))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ cfg_addr = (unsigned char *)(tsi_mk_config_addr(bus->number,
+ devfunc, offset) |
+ (offset & 0x03));
+
+#ifdef DEBUG
+ printk("PCI CFG write : ");
+ printk("%d:0x%x:0x%x ", bus->number, devfunc, offset);
+ printk("%d ADDR=0x%08x ", len, (uint) cfg_addr);
+ printk("data = 0x%08x\n", val);
+#endif
+
+ switch (len) {
+ case 1:
+ out_8((u8 *) cfg_addr, val);
+ break;
+ case 2:
+ out_le16((u16 *) cfg_addr, val);
+ break;
+ default:
+ out_le32((u32 *) cfg_addr, val);
+ break;
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+void tsi108_clear_pci_error(u32 pci_cfg_base)
+{
+ u32 err_stat, err_addr, pci_stat;
+
+ /*
+ * Quietly clear PB and PCI error flags set as result
+ * of PCI/X configuration read requests.
+ */
+
+ /* Read PB Error Log Registers */
+
+ err_stat = tsi108_read_reg(TSI108_PB_OFFSET + TSI108_PB_ERRCS);
+ err_addr = tsi108_read_reg(TSI108_PB_OFFSET + TSI108_PB_AERR);
+
+ if (err_stat & TSI108_PB_ERRCS_ES) {
+ /* Clear error flag */
+ tsi108_write_reg(TSI108_PB_OFFSET + TSI108_PB_ERRCS,
+ TSI108_PB_ERRCS_ES);
+
+ /* Clear read error reported in PB_ISR */
+ tsi108_write_reg(TSI108_PB_OFFSET + TSI108_PB_ISR,
+ TSI108_PB_ISR_PBS_RD_ERR);
+
+ /* Clear PCI/X bus cfg errors if applicable */
+ if ((err_addr & 0xFF000000) == pci_cfg_base) {
+ pci_stat =
+ tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_CSR);
+ tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_CSR,
+ pci_stat);
+ }
+ }
+
+ return;
+}
+
+#define __tsi108_read_pci_config(x, addr, op) \
+ __asm__ __volatile__( \
+ " "op" %0,0,%1\n" \
+ "1: eieio\n" \
+ "2:\n" \
+ ".section .fixup,\"ax\"\n" \
+ "3: li %0,-1\n" \
+ " b 2b\n" \
+ ".section __ex_table,\"a\"\n" \
+ " .align 2\n" \
+ " .long 1b,3b\n" \
+ ".text" \
+ : "=r"(x) : "r"(addr))
+
+int
+tsi108_direct_read_config(struct pci_bus *bus, unsigned int devfn, int offset,
+ int len, u32 * val)
+{
+ volatile unsigned char *cfg_addr;
+ u32 temp;
+
+ if (ppc_md.pci_exclude_device)
+ if (ppc_md.pci_exclude_device(bus->number, devfn))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ cfg_addr = (unsigned char *)(tsi_mk_config_addr(bus->number,
+ devfn,
+ offset) | (offset &
+ 0x03));
+
+ switch (len) {
+ case 1:
+ __tsi108_read_pci_config(temp, cfg_addr, "lbzx");
+ break;
+ case 2:
+ __tsi108_read_pci_config(temp, cfg_addr, "lhbrx");
+ break;
+ default:
+ __tsi108_read_pci_config(temp, cfg_addr, "lwbrx");
+ break;
+ }
+
+ *val = temp;
+
+#ifdef DEBUG
+ if ((0xFFFFFFFF != temp) && (0xFFFF != temp) && (0xFF != temp)) {
+ printk("PCI CFG read : ");
+ printk("%d:0x%x:0x%x ", bus->number, devfn, offset);
+ printk("%d ADDR=0x%08x ", len, (uint) cfg_addr);
+ printk("data = 0x%x\n", *val);
+ }
+#endif
+ return PCIBIOS_SUCCESSFUL;
+}
+
+void tsi108_clear_pci_cfg_error(void)
+{
+ tsi108_clear_pci_error(TSI108_PCI_CFG_BASE_PHYS);
+}
+
+static struct pci_ops tsi108_direct_pci_ops = {
+ tsi108_direct_read_config,
+ tsi108_direct_write_config
+};
+
+int __init tsi108_setup_pci(struct device_node *dev)
+{
+ int len;
+ struct pci_controller *hose;
+ struct resource rsrc;
+ int *bus_range;
+ int primary = 0, has_address = 0;
+
+ /* PCI Config mapping */
+ tsi108_pci_cfg_base = (u32)ioremap(TSI108_PCI_CFG_BASE_PHYS,
+ TSI108_PCI_CFG_SIZE);
+ DBG("TSI_PCI: %s tsi108_pci_cfg_base=0x%x\n", __FUNCTION__,
+ tsi108_pci_cfg_base);
+
+ /* Fetch host bridge registers address */
+ has_address = (of_address_to_resource(dev, 0, &rsrc) == 0);
+
+ /* Get bus range if any */
+ bus_range = (int *)get_property(dev, "bus-range", &len);
+ if (bus_range == NULL || len < 2 * sizeof(int)) {
+ printk(KERN_WARNING "Can't get bus-range for %s, assume"
+ " bus 0\n", dev->full_name);
+ }
+
+ hose = pcibios_alloc_controller();
+
+ if (!hose) {
+ printk("PCI Host bridge init failed\n");
+ return -ENOMEM;
+ }
+ hose->arch_data = dev;
+ hose->set_cfg_type = 1;
+
+ hose->first_busno = bus_range ? bus_range[0] : 0;
+ hose->last_busno = bus_range ? bus_range[1] : 0xff;
+
+ (hose)->ops = &tsi108_direct_pci_ops;
+
+ printk(KERN_INFO "Found tsi108 PCI host bridge at 0x%08lx. "
+ "Firmware bus number: %d->%d\n",
+ rsrc.start, hose->first_busno, hose->last_busno);
+
+ /* Interpret the "ranges" property */
+ /* This also maps the I/O region and sets isa_io/mem_base */
+ pci_process_bridge_OF_ranges(hose, dev, primary);
+ return 0;
+}
+
+/*
+ * Low level utility functions
+ */
+
+static void tsi108_pci_int_mask(u_int irq)
+{
+ u_int irp_cfg;
+ int int_line = (irq - IRQ_PCI_INTAD_BASE);
+
+ irp_cfg = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL);
+ mb();
+ irp_cfg |= (1 << int_line); /* INTx_DIR = output */
+ irp_cfg &= ~(3 << (8 + (int_line * 2))); /* INTx_TYPE = unused */
+ tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL, irp_cfg);
+ mb();
+ irp_cfg = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL);
+}
+
+static void tsi108_pci_int_unmask(u_int irq)
+{
+ u_int irp_cfg;
+ int int_line = (irq - IRQ_PCI_INTAD_BASE);
+
+ irp_cfg = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL);
+ mb();
+ irp_cfg &= ~(1 << int_line);
+ irp_cfg |= (3 << (8 + (int_line * 2)));
+ tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL, irp_cfg);
+ mb();
+}
+
+static void init_pci_source(void)
+{
+ tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL,
+ 0x0000ff00);
+ tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE,
+ TSI108_PCI_IRP_ENABLE_P_INT);
+ mb();
+}
+
+static inline int get_pci_source(void)
+{
+ u_int temp = 0;
+ int irq = -1;
+ int i;
+ u_int pci_irp_stat;
+ static int mask = 0;
+
+ /* Read PCI/X block interrupt status register */
+ pci_irp_stat = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_STAT);
+ mb();
+
+ if (pci_irp_stat & TSI108_PCI_IRP_STAT_P_INT) {
+ /* Process Interrupt from PCI bus INTA# - INTD# lines */
+ temp =
+ tsi108_read_reg(TSI108_PCI_OFFSET +
+ TSI108_PCI_IRP_INTAD) & 0xf;
+ mb();
+ for (i = 0; i < 4; i++, mask++) {
+ if (temp & (1 << mask % 4)) {
+ irq = IRQ_PCI_INTA + mask % 4;
+ mask++;
+ break;
+ }
+ }
+
+ /* Disable interrupts from PCI block */
+ temp = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE);
+ tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE,
+ temp & ~TSI108_PCI_IRP_ENABLE_P_INT);
+ mb();
+ (void)tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE);
+ mb();
+ }
+#ifdef DEBUG
+ else {
+ printk("TSI108_PIC: error in TSI108_PCI_IRP_STAT\n");
+ pci_irp_stat =
+ tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_STAT);
+ temp =
+ tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_INTAD);
+ mb();
+ printk(">> stat=0x%08x intad=0x%08x ", pci_irp_stat, temp);
+ temp =
+ tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL);
+ mb();
+ printk("cfg_ctl=0x%08x ", temp);
+ temp =
+ tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE);
+ mb();
+ printk("irp_enable=0x%08x\n", temp);
+ }
+#endif /* end of DEBUG */
+
+ return irq;
+}
+
+
+/*
+ * Linux descriptor level callbacks
+ */
+
+static void tsi108_pci_irq_enable(u_int irq)
+{
+ tsi108_pci_int_unmask(irq);
+}
+
+static void tsi108_pci_irq_disable(u_int irq)
+{
+ tsi108_pci_int_mask(irq);
+}
+
+static void tsi108_pci_irq_ack(u_int irq)
+{
+ tsi108_pci_int_mask(irq);
+}
+
+static void tsi108_pci_irq_end(u_int irq)
+{
+ tsi108_pci_int_unmask(irq);
+
+ /* Enable interrupts from PCI block */
+ tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE,
+ tsi108_read_reg(TSI108_PCI_OFFSET +
+ TSI108_PCI_IRP_ENABLE) |
+ TSI108_PCI_IRP_ENABLE_P_INT);
+ mb();
+}
+
+/*
+ * Interrupt controller descriptor for cascaded PCI interrupt controller.
+ */
+
+struct hw_interrupt_type tsi108_pci_irq = {
+ .typename = "tsi108_PCI_int",
+ .enable = tsi108_pci_irq_enable,
+ .disable = tsi108_pci_irq_disable,
+ .ack = tsi108_pci_irq_ack,
+ .end = tsi108_pci_irq_end,
+};
+
+/*
+ * Exported functions
+ */
+
+/*
+ * The Tsi108 PCI interrupts initialization routine.
+ *
+ * The INTA# - INTD# interrupts on the PCI bus are reported by the PCI block
+ * to the MPIC using single interrupt source (IRQ_TSI108_PCI). Therefore the
+ * PCI block has to be treated as a cascaded interrupt controller connected
+ * to the MPIC.
+ */
+
+void __init tsi108_pci_int_init(void)
+{
+ u_int i;
+
+ DBG("Tsi108_pci_int_init: initializing PCI interrupts\n");
+
+ for (i = 0; i < NUM_PCI_IRQS; i++) {
+ irq_desc[i + IRQ_PCI_INTAD_BASE].handler = &tsi108_pci_irq;
+ irq_desc[i + IRQ_PCI_INTAD_BASE].status |= IRQ_LEVEL;
+ }
+
+ init_pci_source();
+}
+
+int tsi108_irq_cascade(struct pt_regs *regs, void *unused)
+{
+ return get_pci_source();
+}
diff --git a/include/asm-powerpc/tsi108.h b/include/asm-powerpc/tsi108.h
new file mode 100644
index 0000000..c4c278d
--- /dev/null
+++ b/include/asm-powerpc/tsi108.h
@@ -0,0 +1,109 @@
+/*
+ * include/asm-ppc/tsi108.h
+ *
+ * common routine and memory layout for Tundra TSI108(Grendel) host bridge
+ * memory controller.
+ *
+ * Author: Jacob Pan (jacob.pan@freescale.com)
+ * Alex Bounine (alexandreb@tundra.com)
+ * 2004 (c) Freescale Semiconductor Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#ifndef __PPC_KERNEL_TSI108_H
+#define __PPC_KERNEL_TSI108_H
+
+#include <asm/pci-bridge.h>
+
+/* Size of entire register space */
+#define TSI108_REG_SIZE (0x10000)
+
+/* Sizes of register spaces for individual blocks */
+#define TSI108_HLP_SIZE 0x1000
+#define TSI108_PCI_SIZE 0x1000
+#define TSI108_CLK_SIZE 0x1000
+#define TSI108_PB_SIZE 0x1000
+#define TSI108_SD_SIZE 0x1000
+#define TSI108_DMA_SIZE 0x1000
+#define TSI108_ETH_SIZE 0x1000
+#define TSI108_I2C_SIZE 0x400
+#define TSI108_MPIC_SIZE 0x400
+#define TSI108_UART0_SIZE 0x200
+#define TSI108_GPIO_SIZE 0x200
+#define TSI108_UART1_SIZE 0x200
+
+/* Offsets within Tsi108(A) CSR space for individual blocks */
+#define TSI108_HLP_OFFSET 0x0000
+#define TSI108_PCI_OFFSET 0x1000
+#define TSI108_CLK_OFFSET 0x2000
+#define TSI108_PB_OFFSET 0x3000
+#define TSI108_SD_OFFSET 0x4000
+#define TSI108_DMA_OFFSET 0x5000
+#define TSI108_ETH_OFFSET 0x6000
+#define TSI108_I2C_OFFSET 0x7000
+#define TSI108_MPIC_OFFSET 0x7400
+#define TSI108_UART0_OFFSET 0x7800
+#define TSI108_GPIO_OFFSET 0x7A00
+#define TSI108_UART1_OFFSET 0x7C00
+
+/* Tsi108 registers used by common code components */
+#define TSI108_PCI_CSR (0x004)
+#define TSI108_PCI_IRP_CFG_CTL (0x180)
+#define TSI108_PCI_IRP_STAT (0x184)
+#define TSI108_PCI_IRP_ENABLE (0x188)
+#define TSI108_PCI_IRP_INTAD (0x18C)
+
+#define TSI108_PCI_IRP_STAT_P_INT (0x00400000)
+#define TSI108_PCI_IRP_ENABLE_P_INT (0x00400000)
+
+#define TSI108_CG_PWRUP_STATUS (0x234)
+
+#define TSI108_PB_ISR (0x00C)
+#define TSI108_PB_ERRCS (0x404)
+#define TSI108_PB_AERR (0x408)
+
+#define TSI108_PB_ERRCS_ES (1 << 1)
+#define TSI108_PB_ISR_PBS_RD_ERR (1 << 8)
+
+#define TSI108_PCI_CFG_BASE_PHYS (0xfb000000)
+#define TSI108_PCI_CFG_SIZE (0x01000000)
+/* Global variables */
+
+extern u32 tsi108_pci_cfg_base;
+/* Exported functions */
+
+extern int tsi108_bridge_init(struct pci_controller *hose, uint phys_csr_base);
+extern unsigned long tsi108_get_mem_size(void);
+extern unsigned long tsi108_get_cpu_clk(void);
+extern unsigned long tsi108_get_sdc_clk(void);
+extern int tsi108_direct_write_config(struct pci_bus *bus, unsigned int devfn,
+ int offset, int len, u32 val);
+extern int tsi108_direct_read_config(struct pci_bus *bus, unsigned int devfn,
+ int offset, int len, u32 * val);
+extern void tsi108_clear_pci_error(u32 pci_cfg_base);
+
+extern phys_addr_t get_csrbase(void);
+
+typedef struct {
+ u32 regs; /* hw registers base address */
+ u32 phyregs; /* phy registers base address */
+ u16 phy; /* phy address */
+ u16 irq_num; /* irq number */
+ u8 mac_addr[6]; /* phy mac address */
+} hw_info;
+
+extern u32 get_vir_csrbase(void);
+extern u32 tsi108_csr_vir_base;
+
+extern inline u32 tsi108_read_reg(u32 reg_offset)
+{
+ return in_be32((volatile u32 *)(tsi108_csr_vir_base + reg_offset));
+}
+
+extern inline void tsi108_write_reg(u32 reg_offset, u32 val)
+{
+ out_be32((volatile u32 *)(tsi108_csr_vir_base + reg_offset), val);
+}
+
+#endif /* __PPC_KERNEL_TSI108_H */
^ permalink raw reply related
* [PATCH/2.6.17-rc6 1/4 v2] Powerpc: Add general support for mpc74 48hpc2 (Taiga) platform
From: Zang Roy-r61911 @ 2006-06-13 7:07 UTC (permalink / raw)
To: Paul Mackerras, Benjamin Herrenschmidt
Cc: linuxppc-dev list, Alexandre.Bounine, Yang Xin-Xin-r48390
Add support for Freescale mpc7448 (Taiga) board support
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
---
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 6729c98..d8a9add 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -323,7 +323,7 @@ config PPC_ISERIES
config EMBEDDED6xx
bool "Embedded 6xx/7xx/7xxx-based board"
- depends on PPC32 && BROKEN
+ depends on PPC32 && (BROKEN||BROKEN_ON_SMP)
config APUS
bool "Amiga-APUS"
@@ -408,7 +408,8 @@ config U3_DART
default n
config MPIC
- depends on PPC_PSERIES || PPC_PMAC || PPC_MAPLE || PPC_CHRP
+ depends on PPC_PSERIES || PPC_PMAC || PPC_MAPLE || PPC_CHRP \
+ || MPC7448HPC2
bool
default y
@@ -798,7 +799,8 @@ config MCA
bool
config PCI
- bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_85xx || PPC_MPC52xx || (EMBEDDED && PPC_ISERIES)
+ bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_85xx || PPC_MPC52xx || (EMBEDDED && PPC_ISERIES) \
+ || MPC7448HPC2
default y if !40x && !CPM2 && !8xx && !APUS && !PPC_83xx && !PPC_85xx
default PCI_PERMEDIA if !4xx && !CPM2 && !8xx && APUS
default PCI_QSPAN if !4xx && !CPM2 && 8xx
diff --git a/arch/powerpc/kernel/legacy_serial.c b/arch/powerpc/kernel/legacy_serial.c
index 6e67b5b..c0e19ef 100644
--- a/arch/powerpc/kernel/legacy_serial.c
+++ b/arch/powerpc/kernel/legacy_serial.c
@@ -302,6 +302,17 @@ void __init find_legacy_serial_ports(voi
of_node_put(isa);
}
+ /* First fill our array with tsi-bridge ports */
+ for (np = NULL; (np = of_find_compatible_node(np, "serial", "ns16550")) != NULL;) {
+ struct device_node *tsi = of_get_parent(np);
+ if (tsi && !strcmp(tsi->type, "tsi-bridge")) {
+ index = add_legacy_soc_port(np, np);
+ if (index >= 0 && np == stdout)
+ legacy_serial_console = index;
+ }
+ of_node_put(tsi);
+ }
+
#ifdef CONFIG_PCI
/* Next, try to locate PCI ports */
for (np = NULL; (np = of_find_all_nodes(np));) {
diff --git a/arch/powerpc/platforms/Makefile b/arch/powerpc/platforms/Makefile
index c4f6b0d..308fead 100644
--- a/arch/powerpc/platforms/Makefile
+++ b/arch/powerpc/platforms/Makefile
@@ -13,3 +13,4 @@ obj-$(CONFIG_PPC_PSERIES) += pseries/
obj-$(CONFIG_PPC_ISERIES) += iseries/
obj-$(CONFIG_PPC_MAPLE) += maple/
obj-$(CONFIG_PPC_CELL) += cell/
+obj-$(CONFIG_EMBEDDED6xx) += embedded6xx/
diff --git a/arch/powerpc/platforms/embedded6xx/Kconfig b/arch/powerpc/platforms/embedded6xx/Kconfig
index 4fdbc9a..2b78196 100644
--- a/arch/powerpc/platforms/embedded6xx/Kconfig
+++ b/arch/powerpc/platforms/embedded6xx/Kconfig
@@ -74,6 +74,16 @@ config SANDPOINT
Select SANDPOINT if configuring for a Motorola Sandpoint X3
(any flavor).
+config MPC7448HPC2
+ bool "Freescale MPC7448HPC2(Taiga)"
+ select TSI108_BRIDGE
+ select DEFAULT_UIMAGE
+ select PPC_UDBG_16550
+ select MPIC
+ help
+ Select MPC7448HPC2 if configuring for Freescale MPC7448HPC2 (Taiga)
+ platform
+
config RADSTONE_PPC7D
bool "Radstone Technology PPC7D board"
select PPC_I8259
@@ -221,6 +231,11 @@ config MV64X60
select PPC_INDIRECT_PCI
default y
+config TSI108_BRIDGE
+ bool
+ depends on MPC7448HPC2
+ default y
+
menu "Set bridge options"
depends on MV64X60
diff --git a/arch/powerpc/platforms/embedded6xx/Makefile b/arch/powerpc/platforms/embedded6xx/Makefile
new file mode 100644
index 0000000..fa499fe
--- /dev/null
+++ b/arch/powerpc/platforms/embedded6xx/Makefile
@@ -0,0 +1,4 @@
+#
+# Makefile for the 6xx/7xx/7xxxx linux kernel.
+#
+obj-$(CONFIG_MPC7448HPC2) += mpc7448_hpc2.o
diff --git a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c
new file mode 100644
index 0000000..1273bd6
--- /dev/null
+++ b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c
@@ -0,0 +1,335 @@
+/*
+ * mpc7448_hpc2.c
+ *
+ * Board setup routines for the Freescale Taiga platform
+ *
+ * Author: Jacob Pan
+ * jacob.pan@freescale.com
+ * Author: Xianghua Xiao
+ * x.xiao@freescale.com
+ * Maintainer: Roy Zang <tie-fei.zang@freescale.com>
+ * Add Flat Device Tree support fot mpc7448hpc2 board
+ *
+ * Copyright 2004-2006 Freescale Semiconductor, Inc.
+ *
+ * This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/ide.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_core.h>
+
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/tsi108.h>
+#include <asm/pci-bridge.h>
+#include <asm/reg.h>
+#include <mm/mmu_decl.h>
+#include "mpc7448_hpc2.h"
+#include <asm/tsi108_irq.h>
+#include <asm/mpic.h>
+
+#undef DEBUG
+#ifdef DEBUG
+#define DBG(fmt...) do { printk(fmt); } while(0)
+#else
+#define DBG(fmt...) do { } while(0)
+#endif
+
+#ifndef CONFIG_PCI
+isa_io_base = MPC7448_HPC2_ISA_IO_BASE;
+isa_mem_base = MPC7448_HPC2_ISA_MEM_BASE;
+pci_dram_offset = MPC7448_HPC2_PCI_MEM_OFFSET;
+#endif
+
+extern int tsi108_setup_pci(struct device_node *dev);
+extern void _nmask_and_or_msr(unsigned long nmask, unsigned long or_val);
+extern void tsi108_pci_int_init(void);
+extern int tsi108_irq_cascade(struct pt_regs *regs, void *unused);
+
+/*
+ * Define all of the IRQ senses and polarities. Taken from the
+ * mpc7448hpc manual.
+ * Note: Likely, this table and the following function should be
+ * obtained and derived from the OF Device Tree.
+ */
+
+static u_char mpc7448_hpc2_pic_initsenses[] __initdata = {
+ /* External on-board sources */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* INT[0] XINT0 from FPGA */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* INT[1] XINT1 from FPGA */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* INT[2] PHY_INT from both GIGE */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* INT[3] RESERVED */
+ /* Internal Tsi108/109 interrupt sources */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* DMA0 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* DMA1 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* DMA2 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* DMA3 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* UART0 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* UART1 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* I2C */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* GPIO */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_POSITIVE), /* GIGE0 */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_POSITIVE), /* GIGE1 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* HLP */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* SDC */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Processor IF */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_POSITIVE), /* PCI/X block */
+};
+
+int mpc7448_hpc2_exclude_device(u_char bus, u_char devfn)
+{
+ if (bus == 0 && PCI_SLOT(devfn) == 0)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ else
+ return PCIBIOS_SUCCESSFUL;
+}
+
+/*
+ * find pci slot by devfn in interrupt map of OF tree
+ */
+u8 find_slot_by_devfn(unsigned int *interrupt_map, unsigned int devfn)
+{
+ int i;
+ unsigned int tmp;
+ for (i = 0; i < 4; i++){
+ tmp = interrupt_map[i*4*7];
+ if ((tmp >> 11) == (devfn >> 3))
+ return i;
+ }
+ return i;
+}
+
+/*
+ * Scans the interrupt map for pci device
+ */
+void mpc7448_hpc2_fixup_irq(struct pci_dev *dev)
+{
+ struct pci_controller *hose;
+ struct device_node *node;
+ unsigned int *interrupt;
+ int busnr;
+ int len;
+ u8 slot;
+ u8 pin;
+
+ /* Lookup the hose */
+ busnr = dev->bus->number;
+ hose = pci_bus_to_hose(busnr);
+ if (!hose)
+ printk(KERN_ERR "No pci hose found\n");
+
+ /* Check it has an OF node associated */
+ node = (struct device_node *) hose->arch_data;
+ if (!node)
+ printk(KERN_ERR "No pci node found\n");
+
+ interrupt = (unsigned int *) get_property(node, "interrupt-map", &len);
+ slot = find_slot_by_devfn(interrupt, dev->devfn);
+ pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
+ if (pin == 0 || pin > 4)
+ pin = 1;
+ pin--;
+ dev->irq = interrupt[slot*4*7 + pin*7 + 5];
+ DBG("TSI_PCI: dev->irq = 0x%x\n", dev->irq);
+}
+/* temporary pci irq map fixup*/
+
+void __init mpc7448_hpc2_pcibios_fixup(void)
+{
+ struct pci_dev *dev = NULL;
+ for_each_pci_dev(dev) {
+ mpc7448_hpc2_fixup_irq(dev);
+ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq);
+ }
+}
+
+static void __init mpc7448_hpc2_setup_arch(void)
+{
+ struct device_node *cpu;
+ struct device_node *np;
+ if (ppc_md.progress)
+ ppc_md.progress("mpc7448_hpc2_setup_arch():set_bridge", 0);
+
+ cpu = of_find_node_by_type(NULL, "cpu");
+ if (cpu != 0) {
+ unsigned int *fp;
+
+ fp = (int *)get_property(cpu, "clock-frequency", NULL);
+ if (fp != 0)
+ loops_per_jiffy = *fp / HZ;
+ else
+ loops_per_jiffy = 50000000 / HZ;
+ of_node_put(cpu);
+ }
+ tsi108_csr_vir_base = get_vir_csrbase();
+
+#ifdef CONFIG_ROOT_NFS
+ ROOT_DEV = Root_NFS;
+#else
+ ROOT_DEV = Root_HDA1;
+#endif
+
+#ifdef CONFIG_BLK_DEV_INITRD
+ ROOT_DEV = Root_RAM0;
+#endif
+
+ /* setup PCI host bridge */
+#ifdef CONFIG_PCI
+ for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
+ tsi108_setup_pci(np);
+
+ ppc_md.pci_exclude_device = mpc7448_hpc2_exclude_device;
+ if (ppc_md.progress)
+ ppc_md.progress("tsi108: resources set", 0x100);
+#endif
+
+ printk(KERN_INFO "MPC7448HPC2 (TAIGA) Platform\n");
+ printk(KERN_INFO
+ "Jointly ported by Freescale and Tundra Semiconductor\n");
+ printk(KERN_INFO
+ "Enabling L2 cache then enabling the HID0 prefetch engine.\n");
+}
+
+/*
+ * Interrupt setup and service. Interrrupts on the mpc7448_hpc2 come
+ * from the four external INT pins, PCI interrupts are routed via
+ * PCI interrupt control registers, it generates internal IRQ23
+ *
+ * Interrupt routing on the Taiga Board:
+ * TSI108:PB_INT[0] -> CPU0:INT#
+ * TSI108:PB_INT[1] -> CPU0:MCP#
+ * TSI108:PB_INT[2] -> N/C
+ * TSI108:PB_INT[3] -> N/C
+ */
+static void __init mpc7448_hpc2_init_IRQ(void)
+{
+ struct mpic *mpic;
+ phys_addr_t mpic_paddr = 0;
+ struct device_node *tsi_pic;
+
+ tsi_pic = of_find_node_by_type(NULL, "open-pic");
+ if (tsi_pic) {
+ unsigned int size;
+ void *prop = get_property(tsi_pic, "reg", &size);
+ mpic_paddr = of_translate_address(tsi_pic, prop);
+ }
+
+ if (mpic_paddr == 0) {
+ printk("%s: No tsi108 PIC found !\n", __FUNCTION__);
+ return;
+ }
+
+ DBG("%s: tsi108pic phys_addr = 0x%x\n", __FUNCTION__,
+ (u32) mpic_paddr);
+
+ mpic = mpic_alloc(mpic_paddr,
+ MPIC_PRIMARY | MPIC_BIG_ENDIAN | MPIC_WANTS_RESET |
+ MPIC_SPV_EOI | MPIC_MOD_ID(MPIC_ID_TSI108),
+ 0, /* num_sources used */
+ TSI108_IRQ_BASE,
+ 0, /* num_sources used */
+ NR_IRQS - 4 /* XXXX */,
+ mpc7448_hpc2_pic_initsenses,
+ sizeof(mpc7448_hpc2_pic_initsenses), "Tsi108_PIC");
+
+ BUG_ON(mpic == NULL); /* XXXX */
+
+ mpic_init(mpic);
+ mpic_setup_cascade(IRQ_TSI108_PCI, tsi108_irq_cascade, mpic);
+ tsi108_pci_int_init();
+
+ /* Configure MPIC outputs to CPU0 */
+ tsi108_write_reg(TSI108_MPIC_OFFSET + 0x30c, 0);
+}
+
+void mpc7448_hpc2_show_cpuinfo(struct seq_file *m)
+{
+ seq_printf(m, "vendor\t\t: Freescale Semiconductor\n");
+ seq_printf(m, "machine\t\t: MPC7448hpc2\n");
+}
+
+void mpc7448_hpc2_restart(char *cmd)
+{
+ local_irq_disable();
+
+ /* Set exception prefix high - to the firmware */
+ _nmask_and_or_msr(0, MSR_IP);
+
+ for (;;) ; /* Spin until reset happens */
+}
+
+void mpc7448_hpc2_power_off(void)
+{
+ local_irq_disable();
+ for (;;) ; /* No way to shut power off with software */
+}
+
+void mpc7448_hpc2_halt(void)
+{
+ mpc7448_hpc2_power_off();
+}
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init mpc7448_hpc2_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ if (!of_flat_dt_is_compatible(root, "mpc74xx"))
+ return 0;
+ return 1;
+}
+
+static int mpc7448_machine_check_exception(struct pt_regs *regs)
+{
+ extern void tsi108_clear_pci_cfg_error(void);
+ const struct exception_table_entry *entry;
+
+ /* Are we prepared to handle this fault */
+ if ((entry = search_exception_tables(regs->nip)) != NULL) {
+ tsi108_clear_pci_cfg_error();
+ regs->msr |= MSR_RI;
+ regs->nip = entry->fixup;
+ return 1;
+ }
+ return 0;
+
+}
+define_machine(mpc7448_hpc2){
+ .name = "MPC7448 HPC2",
+ .probe = mpc7448_hpc2_probe,
+ .setup_arch = mpc7448_hpc2_setup_arch,
+ .init_IRQ = mpc7448_hpc2_init_IRQ,
+ .show_cpuinfo = mpc7448_hpc2_show_cpuinfo,
+ .get_irq = mpic_get_irq,
+ .pcibios_fixup = mpc7448_hpc2_pcibios_fixup,
+ .restart = mpc7448_hpc2_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .machine_check_exception= mpc7448_machine_check_exception,
+ .progress = udbg_progress,
+};
diff --git a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.h b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.h
new file mode 100644
index 0000000..8296990
--- /dev/null
+++ b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.h
@@ -0,0 +1,26 @@
+/*
+ * mpc7448_hpc2.h
+ *
+ * Definitions for Freescale MPC7448_HPC2 platform
+ *
+ * Author: Jacob Pan
+ * jacob.pan@freescale.com
+ * Maintainer: Roy Zang <roy.zang@freescale.com>
+ *
+ * 2006 (c) Freescale Semiconductor, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#ifndef __PPC_PLATFORMS_MPC7448_HPC2_H
+#define __PPC_PLATFORMS_MPC7448_HPC2_H
+
+#include <asm/ppcboot.h>
+
+/* Base Addresses for the PCI bus
+ */
+#define MPC7448_HPC2_PCI_MEM_OFFSET (0x00000000)
+#define MPC7448_HPC2_ISA_IO_BASE (0x00000000)
+#define MPC7448_HPC2_ISA_MEM_BASE (0x00000000)
+#endif /* __PPC_PLATFORMS_MPC7448_HPC2_H */
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox