From: Archit Taneja <architt@codeaurora.org>
To: John Stultz <john.stultz@linaro.org>,
lkml <linux-kernel@vger.kernel.org>
Cc: David Airlie <airlied@linux.ie>,
Wolfram Sang <wsa+renesas@sang-engineering.com>,
Lars-Peter Clausen <lars@metafoo.de>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
dri-devel@lists.freedesktop.org
Subject: Re: [RFC][PATCH 0/5 v2] adv7511 EDID probing improvements
Date: Mon, 12 Dec 2016 14:10:44 +0530 [thread overview]
Message-ID: <10bc366d-9955-1f03-7136-9fb05eee943f@codeaurora.org> (raw)
In-Reply-To: <1480395884-5471-1-git-send-email-john.stultz@linaro.org>
Hi,
On 11/29/2016 10:34 AM, John Stultz wrote:
> Wanted to send out v2 of this patch set improving the EDID
> probing on the adv7511 used on HiKey.
>
> The first three patches are fixups that are hopefully straight
> forward, integrating feedback I got from Laurant.
>
> One of the previous patches that Laurant had concerns about, I
> broke into two patches, which are the last two in this series.
> The core issue seems to be something going wrong with the regmap
> cache state for the ADV7511_REG_EDID_I2C_ADDR (0x43) register
> which results in i2c_transfer errors if we don't do the
> regcache_sync/_mark_dirty() calls. I suspect there might be a
> better solution there, so suggestions will be very welcome.
>
> Thoughts and feedback would be appreciated!
I tested this for ADV7533 on DB410c and it works well. We can
pull this if it works fine for ADV7511 too. Laurent, could we
get an Ack for the series from you?
Thanks,
Archit
>
> thanks
> -john
>
> Cc: David Airlie <airlied@linux.ie>
> Cc: Archit Taneja <architt@codeaurora.org>
> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Cc: Lars-Peter Clausen <lars@metafoo.de>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
>
> Archit Taneja (1):
> drm/bridge: adv7511: Enable HPD interrupts to support hotplug and
> improve monitor detection
>
> John Stultz (4):
> drm/bridge: adv7511: Use work_struct to defer hotplug handing to out
> of irq context
> drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
> drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be
> reused internally
> drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
>
> drivers/gpu/drm/bridge/adv7511/adv7511.h | 2 ++
> drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 49 ++++++++++++++++------------
> 2 files changed, 31 insertions(+), 20 deletions(-)
>
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
next prev parent reply other threads:[~2016-12-12 8:40 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-29 5:04 [RFC][PATCH 0/5 v2] adv7511 EDID probing improvements John Stultz
2016-11-29 5:04 ` [RFC][PATCH 1/5 v2] drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context John Stultz
2016-11-29 6:46 ` Laurent Pinchart
2016-11-29 17:04 ` John Stultz
2016-11-29 5:04 ` [RFC][PATCH 2/5 v2] drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event() John Stultz
2016-11-29 6:50 ` Laurent Pinchart
2016-11-29 17:58 ` John Stultz
2016-11-29 5:04 ` [RFC][PATCH 3/5 v2] drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection John Stultz
2016-11-29 5:04 ` [RFC][PATCH 4/5 v2] drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally John Stultz
2016-11-29 5:04 ` [RFC][PATCH 5/5 v2] drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID John Stultz
2016-11-30 4:42 ` Archit Taneja
2016-12-12 8:40 ` Archit Taneja [this message]
2016-12-12 19:06 ` [RFC][PATCH 0/5 v2] adv7511 EDID probing improvements John Stultz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=10bc366d-9955-1f03-7136-9fb05eee943f@codeaurora.org \
--to=architt@codeaurora.org \
--cc=airlied@linux.ie \
--cc=dri-devel@lists.freedesktop.org \
--cc=john.stultz@linaro.org \
--cc=lars@metafoo.de \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=wsa+renesas@sang-engineering.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox