[PATCH AUTOSEL 5.10 1/8] ASoC: allow module autoloading for table db1200_pids

[PATCH AUTOSEL 5.10 1/8] ASoC: allow module autoloading for table db1200_pids

[Sasha Levin]

From: Hongbo Li <lihongbo22@huawei.com>

[ Upstream commit 0e9fdab1e8df490354562187cdbb8dec643eae2c ]

Add MODULE_DEVICE_TABLE(), so modules could be properly
autoloaded based on the alias from platform_device_id table.

Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://patch.msgid.link/20240821061955.2273782-2-lihongbo22@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/au1x/db1200.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/sound/soc/au1x/db1200.c b/sound/soc/au1x/db1200.c
index 5f8baad37a401..48243164b7ac8 100644
--- a/sound/soc/au1x/db1200.c
+++ b/sound/soc/au1x/db1200.c
@@ -44,6 +44,7 @@ static const struct platform_device_id db1200_pids[] = {
 	},
 	{},
 };
+MODULE_DEVICE_TABLE(platform, db1200_pids);
 
 /*-------------------------  AC97 PART  ---------------------------*/
 
-- 
2.43.0

[PATCH AUTOSEL 5.10 2/8] ALSA: hda/realtek - Fixed ALC256 headphone no sound

[Sasha Levin]

From: Kailang Yang <kailang@realtek.com>

[ Upstream commit 9b82ff1362f50914c8292902e07be98a9f59d33d ]

Dell platform, plug headphone or headset, it had a chance to get no
sound from headphone.
Replace depop procedure will solve this issue.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/bb8e2de30d294dc287944efa0667685a@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/pci/hda/patch_realtek.c | 50 ++++++++++++++++++++++++++---------
 1 file changed, 37 insertions(+), 13 deletions(-)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index e8e9cfb4a9357..269e973dde3e8 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -4847,6 +4847,30 @@ static void alc269_fixup_hp_line1_mic1_led(struct hda_codec *codec,
 	}
 }
 
+static void alc_hp_mute_disable(struct hda_codec *codec, unsigned int delay)
+{
+	if (delay <= 0)
+		delay = 75;
+	snd_hda_codec_write(codec, 0x21, 0,
+		    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
+	msleep(delay);
+	snd_hda_codec_write(codec, 0x21, 0,
+		    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
+	msleep(delay);
+}
+
+static void alc_hp_enable_unmute(struct hda_codec *codec, unsigned int delay)
+{
+	if (delay <= 0)
+		delay = 75;
+	snd_hda_codec_write(codec, 0x21, 0,
+		    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
+	msleep(delay);
+	snd_hda_codec_write(codec, 0x21, 0,
+		    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
+	msleep(delay);
+}
+
 static const struct coef_fw alc225_pre_hsmode[] = {
 	UPDATE_COEF(0x4a, 1<<8, 0),
 	UPDATE_COEFEX(0x57, 0x05, 1<<14, 0),
@@ -4948,6 +4972,7 @@ static void alc_headset_mode_unplugged(struct hda_codec *codec)
 	case 0x10ec0236:
 	case 0x10ec0256:
 	case 0x19e58326:
+		alc_hp_mute_disable(codec, 75);
 		alc_process_coef_fw(codec, coef0256);
 		break;
 	case 0x10ec0234:
@@ -5219,6 +5244,7 @@ static void alc_headset_mode_default(struct hda_codec *codec)
 		alc_write_coef_idx(codec, 0x45, 0xc089);
 		msleep(50);
 		alc_process_coef_fw(codec, coef0256);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0234:
 	case 0x10ec0274:
@@ -5316,6 +5342,7 @@ static void alc_headset_mode_ctia(struct hda_codec *codec)
 	case 0x10ec0256:
 	case 0x19e58326:
 		alc_process_coef_fw(codec, coef0256);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0234:
 	case 0x10ec0274:
@@ -5431,6 +5458,7 @@ static void alc_headset_mode_omtp(struct hda_codec *codec)
 	case 0x10ec0256:
 	case 0x19e58326:
 		alc_process_coef_fw(codec, coef0256);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0234:
 	case 0x10ec0274:
@@ -5536,25 +5564,21 @@ static void alc_determine_headset_type(struct hda_codec *codec)
 		alc_write_coef_idx(codec, 0x06, 0x6104);
 		alc_write_coefex_idx(codec, 0x57, 0x3, 0x09a3);
 
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-		msleep(80);
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
-
 		alc_process_coef_fw(codec, coef0255);
 		msleep(300);
 		val = alc_read_coef_idx(codec, 0x46);
 		is_ctia = (val & 0x0070) == 0x0070;
-
+		if (!is_ctia) {
+			alc_write_coef_idx(codec, 0x45, 0xe089);
+			msleep(100);
+			val = alc_read_coef_idx(codec, 0x46);
+			if ((val & 0x0070) == 0x0070)
+				is_ctia = false;
+			else
+				is_ctia = true;
+		}
 		alc_write_coefex_idx(codec, 0x57, 0x3, 0x0da3);
 		alc_update_coefex_idx(codec, 0x57, 0x5, 1<<14, 0);
-
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
-		msleep(80);
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
 		break;
 	case 0x10ec0234:
 	case 0x10ec0274:
-- 
2.43.0

[PATCH AUTOSEL 5.10 3/8] ALSA: hda/realtek - FIxed ALC285 headphone no sound

[Sasha Levin]

From: Kailang Yang <kailang@realtek.com>

[ Upstream commit 1fa7b099d60ad64f559bd3b8e3f0d94b2e015514 ]

Dell platform with ALC215 ALC285 ALC289 ALC225 ALC295 ALC299, plug
headphone or headset.
It had a chance to get no sound from headphone.
Replace depop procedure will solve this issue.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/d0de1b03fd174520945dde216d765223@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/pci/hda/patch_realtek.c | 26 ++++++++++++++------------
 1 file changed, 14 insertions(+), 12 deletions(-)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index 269e973dde3e8..190d21fd83576 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -5007,6 +5007,7 @@ static void alc_headset_mode_unplugged(struct hda_codec *codec)
 	case 0x10ec0295:
 	case 0x10ec0289:
 	case 0x10ec0299:
+		alc_hp_mute_disable(codec, 75);
 		alc_process_coef_fw(codec, alc225_pre_hsmode);
 		alc_process_coef_fw(codec, coef0225);
 		break;
@@ -5232,6 +5233,7 @@ static void alc_headset_mode_default(struct hda_codec *codec)
 	case 0x10ec0299:
 		alc_process_coef_fw(codec, alc225_pre_hsmode);
 		alc_process_coef_fw(codec, coef0225);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0255:
 		alc_process_coef_fw(codec, coef0255);
@@ -5391,6 +5393,7 @@ static void alc_headset_mode_ctia(struct hda_codec *codec)
 			alc_process_coef_fw(codec, coef0225_2);
 		else
 			alc_process_coef_fw(codec, coef0225_1);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	case 0x10ec0867:
 		alc_update_coefex_idx(codec, 0x57, 0x5, 1<<14, 0);
@@ -5496,6 +5499,7 @@ static void alc_headset_mode_omtp(struct hda_codec *codec)
 	case 0x10ec0289:
 	case 0x10ec0299:
 		alc_process_coef_fw(codec, coef0225);
+		alc_hp_enable_unmute(codec, 75);
 		break;
 	}
 	codec_dbg(codec, "Headset jack set to Nokia-style headset mode.\n");
@@ -5655,12 +5659,6 @@ static void alc_determine_headset_type(struct hda_codec *codec)
 	case 0x10ec0295:
 	case 0x10ec0289:
 	case 0x10ec0299:
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE);
-		msleep(80);
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, 0x0);
-
 		alc_process_coef_fw(codec, alc225_pre_hsmode);
 		alc_update_coef_idx(codec, 0x67, 0xf000, 0x1000);
 		val = alc_read_coef_idx(codec, 0x45);
@@ -5677,15 +5675,19 @@ static void alc_determine_headset_type(struct hda_codec *codec)
 			val = alc_read_coef_idx(codec, 0x46);
 			is_ctia = (val & 0x00f0) == 0x00f0;
 		}
+		if (!is_ctia) {
+			alc_update_coef_idx(codec, 0x45, 0x3f<<10, 0x38<<10);
+			alc_update_coef_idx(codec, 0x49, 3<<8, 1<<8);
+			msleep(100);
+			val = alc_read_coef_idx(codec, 0x46);
+			if ((val & 0x00f0) == 0x00f0)
+				is_ctia = false;
+			else
+				is_ctia = true;
+		}
 		alc_update_coef_idx(codec, 0x4a, 7<<6, 7<<6);
 		alc_update_coef_idx(codec, 0x4a, 3<<4, 3<<4);
 		alc_update_coef_idx(codec, 0x67, 0xf000, 0x3000);
-
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT);
-		msleep(80);
-		snd_hda_codec_write(codec, 0x21, 0,
-			    AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE);
 		break;
 	case 0x10ec0867:
 		is_ctia = true;
-- 
2.43.0

[PATCH AUTOSEL 5.10 4/8] pinctrl: at91: make it work with current gpiolib

[Sasha Levin]

From: Thomas Blocher <thomas.blocher@ek-dev.de>

[ Upstream commit 752f387faaae0ae2e84d3f496922524785e77d60 ]

pinctrl-at91 currently does not support the gpio-groups devicetree
property and has no pin-range.
Because of this at91 gpios stopped working since patch
commit 2ab73c6d8323fa1e ("gpio: Support GPIO controllers without pin-ranges")
This was discussed in the patches
commit fc328a7d1fcce263 ("gpio: Revert regression in sysfs-gpio (gpiolib.c)")
commit 56e337f2cf132632 ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")

As a workaround manually set pin-range via gpiochip_add_pin_range() until
a) pinctrl-at91 is reworked to support devicetree gpio-groups
b) another solution as mentioned in
commit 56e337f2cf132632 ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")
is found

Signed-off-by: Thomas Blocher <thomas.blocher@ek-dev.de>
Link: https://lore.kernel.org/5b992862-355d-f0de-cd3d-ff99e67a4ff1@ek-dev.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/pinctrl-at91.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c
index 52ecd47c18e2d..bb9348f14b1ba 100644
--- a/drivers/pinctrl/pinctrl-at91.c
+++ b/drivers/pinctrl/pinctrl-at91.c
@@ -1401,8 +1401,11 @@ static int at91_pinctrl_probe(struct platform_device *pdev)
 
 	/* We will handle a range of GPIO pins */
 	for (i = 0; i < gpio_banks; i++)
-		if (gpio_chips[i])
+		if (gpio_chips[i]) {
 			pinctrl_add_gpio_range(info->pctl, &gpio_chips[i]->range);
+			gpiochip_add_pin_range(&gpio_chips[i]->chip, dev_name(info->pctl->dev), 0,
+				gpio_chips[i]->range.pin_base, gpio_chips[i]->range.npins);
+		}
 
 	dev_info(&pdev->dev, "initialized AT91 pinctrl driver\n");
 
-- 
2.43.0

[PATCH AUTOSEL 5.10 5/8] microblaze: don't treat zero reserved memory regions as error

[Sasha Levin]

From: Mike Rapoport <rppt@kernel.org>

[ Upstream commit 0075df288dd8a7abfe03b3766176c393063591dd ]

Before commit 721f4a6526da ("mm/memblock: remove empty dummy entry") the
check for non-zero of memblock.reserved.cnt in mmu_init() would always
be true either because  memblock.reserved.cnt is initialized to 1 or
because there were memory reservations earlier.

The removal of dummy empty entry in memblock caused this check to fail
because now memblock.reserved.cnt is initialized to 0.

Remove the check for non-zero of memblock.reserved.cnt because it's
perfectly fine to have an empty memblock.reserved array that early in
boot.

Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mike Rapoport <rppt@kernel.org>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240729053327.4091459-1-rppt@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/microblaze/mm/init.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/arch/microblaze/mm/init.c b/arch/microblaze/mm/init.c
index 45da639bd22ca..a2cd139c5eb41 100644
--- a/arch/microblaze/mm/init.c
+++ b/arch/microblaze/mm/init.c
@@ -245,11 +245,6 @@ asmlinkage void __init mmu_init(void)
 {
 	unsigned int kstart, ksize;
 
-	if (!memblock.reserved.cnt) {
-		pr_emerg("Error memory count\n");
-		machine_restart(NULL);
-	}
-
 	if ((u32) memblock.memory.regions[0].size < 0x400000) {
 		pr_emerg("Memory must be greater than 4MB\n");
 		machine_restart(NULL);
-- 
2.43.0

[PATCH AUTOSEL 5.10 6/8] net: ftgmac100: Ensure tx descriptor updates are visible

[Sasha Levin]

From: Jacky Chou <jacky_chou@aspeedtech.com>

[ Upstream commit 4186c8d9e6af57bab0687b299df10ebd47534a0a ]

The driver must ensure TX descriptor updates are visible
before updating TX pointer and TX clear pointer.

This resolves TX hangs observed on AST2600 when running
iperf3.

Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/faraday/ftgmac100.c | 26 ++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 969af4dd64055..bc9a7f2d23504 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -569,7 +569,7 @@ static bool ftgmac100_rx_packet(struct ftgmac100 *priv, int *processed)
 	(*processed)++;
 	return true;
 
- drop:
+drop:
 	/* Clean rxdes0 (which resets own bit) */
 	rxdes->rxdes0 = cpu_to_le32(status & priv->rxdes0_edorr_mask);
 	priv->rx_pointer = ftgmac100_next_rx_pointer(priv, pointer);
@@ -653,6 +653,11 @@ static bool ftgmac100_tx_complete_packet(struct ftgmac100 *priv)
 	ftgmac100_free_tx_packet(priv, pointer, skb, txdes, ctl_stat);
 	txdes->txdes0 = cpu_to_le32(ctl_stat & priv->txdes0_edotr_mask);
 
+	/* Ensure the descriptor config is visible before setting the tx
+	 * pointer.
+	 */
+	smp_wmb();
+
 	priv->tx_clean_pointer = ftgmac100_next_tx_pointer(priv, pointer);
 
 	return true;
@@ -806,6 +811,11 @@ static netdev_tx_t ftgmac100_hard_start_xmit(struct sk_buff *skb,
 	dma_wmb();
 	first->txdes0 = cpu_to_le32(f_ctl_stat);
 
+	/* Ensure the descriptor config is visible before setting the tx
+	 * pointer.
+	 */
+	smp_wmb();
+
 	/* Update next TX pointer */
 	priv->tx_pointer = pointer;
 
@@ -826,7 +836,7 @@ static netdev_tx_t ftgmac100_hard_start_xmit(struct sk_buff *skb,
 
 	return NETDEV_TX_OK;
 
- dma_err:
+dma_err:
 	if (net_ratelimit())
 		netdev_err(netdev, "map tx fragment failed\n");
 
@@ -848,7 +858,7 @@ static netdev_tx_t ftgmac100_hard_start_xmit(struct sk_buff *skb,
 	 * last fragment, so we know ftgmac100_free_tx_packet()
 	 * hasn't freed the skb yet.
 	 */
- drop:
+drop:
 	/* Drop the packet */
 	dev_kfree_skb_any(skb);
 	netdev->stats.tx_dropped++;
@@ -1419,7 +1429,7 @@ static void ftgmac100_reset_task(struct work_struct *work)
 	ftgmac100_init_all(priv, true);
 
 	netdev_dbg(netdev, "Reset done !\n");
- bail:
+bail:
 	if (priv->mii_bus)
 		mutex_unlock(&priv->mii_bus->mdio_lock);
 	if (netdev->phydev)
@@ -1490,15 +1500,15 @@ static int ftgmac100_open(struct net_device *netdev)
 
 	return 0;
 
- err_ncsi:
+err_ncsi:
 	napi_disable(&priv->napi);
 	netif_stop_queue(netdev);
- err_alloc:
+err_alloc:
 	ftgmac100_free_buffers(priv);
 	free_irq(netdev->irq, netdev);
- err_irq:
+err_irq:
 	netif_napi_del(&priv->napi);
- err_hw:
+err_hw:
 	iowrite32(0, priv->base + FTGMAC100_OFFSET_IER);
 	ftgmac100_free_rings(priv);
 	return err;
-- 
2.43.0

[PATCH AUTOSEL 5.10 7/8] wifi: iwlwifi: lower message level for FW buffer destination

[Sasha Levin]

From: Benjamin Berg <benjamin.berg@intel.com>

[ Upstream commit f8a129c1e10256c785164ed5efa5d17d45fbd81b ]

An invalid buffer destination is not a problem for the driver and it
does not make sense to report it with the KERN_ERR message level. As
such, change the message to use IWL_DEBUG_FW.

Reported-by: Len Brown <lenb@kernel.org>
Closes: https://lore.kernel.org/r/CAJvTdKkcxJss=DM2sxgv_MR5BeZ4_OC-3ad6tA40TYH2yqHCWw@mail.gmail.com
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.20abf78f05bc.Ifbcecc2ae9fb40b9698302507dcba8b922c8d856@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c b/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c
index 56f63f5f5dd34..2afa5c91bc76b 100644
--- a/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c
+++ b/drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c
@@ -111,7 +111,8 @@ iwl_pcie_ctxt_info_dbg_enable(struct iwl_trans *trans,
 		}
 		break;
 	default:
-		IWL_ERR(trans, "WRT: Invalid buffer destination\n");
+		IWL_DEBUG_FW(trans, "WRT: Invalid buffer destination (%d)\n",
+			     le32_to_cpu(fw_mon_cfg->buf_location));
 	}
 out:
 	if (dbg_flags)
-- 
2.43.0

[PATCH AUTOSEL 5.10 8/8] wifi: iwlwifi: mvm: don't wait for tx queues if firmware is dead

[Sasha Levin]

From: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

[ Upstream commit 3a84454f5204718ca5b4ad2c1f0bf2031e2403d1 ]

There is a WARNING in iwl_trans_wait_tx_queues_empty() (that was
recently converted from just a message), that can be hit if we
wait for TX queues to become empty after firmware died. Clearly,
we can't expect anything from the firmware after it's declared dead.

Don't call iwl_trans_wait_tx_queues_empty() in this case. While it could
be a good idea to stop the flow earlier, the flush functions do some
maintenance work that is not related to the firmware, so keep that part
of the code running even when the firmware is not running.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.a7cbd794cee9.I44a739fbd4ffcc46b83844dd1c7b2eb0c7b270f6@changeid
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c b/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
index 08008b0c0637c..fa784d8352901 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
@@ -4747,6 +4747,10 @@ static void iwl_mvm_flush_no_vif(struct iwl_mvm *mvm, u32 queues, bool drop)
 	int i;
 
 	if (!iwl_mvm_has_new_tx_api(mvm)) {
+		/* we can't ask the firmware anything if it is dead */
+		if (test_bit(IWL_MVM_STATUS_HW_RESTART_REQUESTED,
+			     &mvm->status))
+			return;
 		if (drop) {
 			mutex_lock(&mvm->mutex);
 			iwl_mvm_flush_tx_path(mvm,
@@ -4828,8 +4832,11 @@ static void iwl_mvm_mac_flush(struct ieee80211_hw *hw,
 
 	/* this can take a while, and we may need/want other operations
 	 * to succeed while doing this, so do it without the mutex held
+	 * If the firmware is dead, this can't work...
 	 */
-	if (!drop && !iwl_mvm_has_new_tx_api(mvm))
+	if (!drop && !iwl_mvm_has_new_tx_api(mvm) &&
+	    !test_bit(IWL_MVM_STATUS_HW_RESTART_REQUESTED,
+		      &mvm->status))
 		iwl_trans_wait_tx_queues_empty(mvm->trans, msk);
 }
 
-- 
2.43.0