* [PATCH 0/3] Add initial support for Canaan Kendryte K230 pinctrl
@ 2024-09-15 14:21 Ze Huang
2024-09-15 15:22 ` Ze Huang
2024-09-15 22:56 ` Inochi Amaoto
0 siblings, 2 replies; 6+ messages in thread
From: Ze Huang @ 2024-09-15 14:21 UTC (permalink / raw)
To: linus.walleij, robh, krzk+dt, conor+dt, paul.walmsley, palmer,
aou, conor
Cc: cyy, jesse, jszhang, inochiama, uwu, zhangmeng.kevin, kevin.z.m,
devicetree, linux-riscv, linux-kernel, dlan, 18771902331
This patch series introduces support for the pinctrl driver of the Canaan
K230 SoC. The K230 SoC features 64 IO pins, each of which can be configured
for up to five different functions.
The controller manages the entire pin configuration and multiplexing
through a single register, which control features such as schmitt trigger,
drive strength, bias pull-up/down, input/output enable, power source, and
mux mode.
The changes have been tested on the K230 development board.
The pin function definition can be found here [1], and most of the DTS data
was converted from the vendor's code [2].
Link: https://developer.canaan-creative.com/k230/dev/_downloads/a53655a81951bc8a440ae647be286e75/K230_PINOUT_V1.1_20230321.xlsx [1]
Link: https://github.com/kendryte/k230_sdk/blob/main/src/little/uboot/arch/riscv/dts/k230_canmv.dts [2]
Ze Huang (3):
dt-bindings: pinctrl: Add support for canaan,k230 SoC
pinctrl: canaan: Add support for k230 SoC
riscv: dts: canaan: Add k230's pinctrl node
.../bindings/pinctrl/canaan,k230-pinctrl.yaml | 128 ++++
arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi | 318 +++++++++
arch/riscv/boot/dts/canaan/k230-pinctrl.h | 18 +
arch/riscv/boot/dts/canaan/k230.dtsi | 2 +
drivers/pinctrl/Kconfig | 10 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-k230.c | 674 ++++++++++++++++++
7 files changed, 1151 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/canaan,k230-pinctrl.yaml
create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi
create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.h
create mode 100644 drivers/pinctrl/pinctrl-k230.c
--
2.46.1
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 0/3] Add initial support for Canaan Kendryte K230 pinctrl
2024-09-15 14:21 [PATCH 0/3] Add initial support for Canaan Kendryte K230 pinctrl Ze Huang
@ 2024-09-15 15:22 ` Ze Huang
2024-09-15 19:35 ` Conor Dooley
2024-09-15 22:56 ` Inochi Amaoto
1 sibling, 1 reply; 6+ messages in thread
From: Ze Huang @ 2024-09-15 15:22 UTC (permalink / raw)
To: linus.walleij, robh, krzk+dt, conor+dt, paul.walmsley, palmer,
aou, conor
Cc: cyy, jesse, jszhang, inochiama, uwu, zhangmeng.kevin, kevin.z.m,
devicetree, linux-riscv, linux-kernel, dlan
On 9/15/24 10:21 PM, Ze Huang wrote:
> This patch series introduces support for the pinctrl driver of the Canaan
> K230 SoC. The K230 SoC features 64 IO pins, each of which can be configured
> for up to five different functions.
>
> The controller manages the entire pin configuration and multiplexing
> through a single register, which control features such as schmitt trigger,
> drive strength, bias pull-up/down, input/output enable, power source, and
> mux mode.
>
> The changes have been tested on the K230 development board.
>
> The pin function definition can be found here [1], and most of the DTS data
> was converted from the vendor's code [2].
>
> Link: https://developer.canaan-creative.com/k230/dev/_downloads/a53655a81951bc8a440ae647be286e75/K230_PINOUT_V1.1_20230321.xlsx [1]
> Link: https://github.com/kendryte/k230_sdk/blob/main/src/little/uboot/arch/riscv/dts/k230_canmv.dts [2]
>
> Ze Huang (3):
> dt-bindings: pinctrl: Add support for canaan,k230 SoC
> pinctrl: canaan: Add support for k230 SoC
> riscv: dts: canaan: Add k230's pinctrl node
>
> .../bindings/pinctrl/canaan,k230-pinctrl.yaml | 128 ++++
> arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi | 318 +++++++++
> arch/riscv/boot/dts/canaan/k230-pinctrl.h | 18 +
> arch/riscv/boot/dts/canaan/k230.dtsi | 2 +
> drivers/pinctrl/Kconfig | 10 +
> drivers/pinctrl/Makefile | 1 +
> drivers/pinctrl/pinctrl-k230.c | 674 ++++++++++++++++++
> 7 files changed, 1151 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/canaan,k230-pinctrl.yaml
> create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi
> create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.h
> create mode 100644 drivers/pinctrl/pinctrl-k230.c
>
lost base commit and prerequisite patch id here:
base-commit: 0eea987088a22d73d81e968de7347cdc7e594f72
prerequisite-patch-id: 740cbeb9fc3f3e3fd30df4914cd31e9eb148a581
prerequisite-patch-id: b5cc919a7e8e2f852569d5918944dbe4f21e6912
prerequisite-patch-id: 554cb838b7264109437359e88443cc3497ed344c
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 0/3] Add initial support for Canaan Kendryte K230 pinctrl
2024-09-15 15:22 ` Ze Huang
@ 2024-09-15 19:35 ` Conor Dooley
2024-09-16 3:50 ` Ze Huang
0 siblings, 1 reply; 6+ messages in thread
From: Conor Dooley @ 2024-09-15 19:35 UTC (permalink / raw)
To: Ze Huang
Cc: linus.walleij, robh, krzk+dt, conor+dt, paul.walmsley, palmer,
aou, cyy, jesse, jszhang, inochiama, uwu, zhangmeng.kevin,
kevin.z.m, devicetree, linux-riscv, linux-kernel, dlan
[-- Attachment #1: Type: text/plain, Size: 2538 bytes --]
On Sun, Sep 15, 2024 at 11:22:16PM +0800, Ze Huang wrote:
>
> On 9/15/24 10:21 PM, Ze Huang wrote:
> > This patch series introduces support for the pinctrl driver of the Canaan
> > K230 SoC. The K230 SoC features 64 IO pins, each of which can be configured
> > for up to five different functions.
> >
> > The controller manages the entire pin configuration and multiplexing
> > through a single register, which control features such as schmitt trigger,
> > drive strength, bias pull-up/down, input/output enable, power source, and
> > mux mode.
> >
> > The changes have been tested on the K230 development board.
> >
> > The pin function definition can be found here [1], and most of the DTS data
> > was converted from the vendor's code [2].
> >
> > Link: https://developer.canaan-creative.com/k230/dev/_downloads/a53655a81951bc8a440ae647be286e75/K230_PINOUT_V1.1_20230321.xlsx [1]
> > Link: https://github.com/kendryte/k230_sdk/blob/main/src/little/uboot/arch/riscv/dts/k230_canmv.dts [2]
> >
> > Ze Huang (3):
> > dt-bindings: pinctrl: Add support for canaan,k230 SoC
> > pinctrl: canaan: Add support for k230 SoC
> > riscv: dts: canaan: Add k230's pinctrl node
> >
> > .../bindings/pinctrl/canaan,k230-pinctrl.yaml | 128 ++++
> > arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi | 318 +++++++++
> > arch/riscv/boot/dts/canaan/k230-pinctrl.h | 18 +
> > arch/riscv/boot/dts/canaan/k230.dtsi | 2 +
> > drivers/pinctrl/Kconfig | 10 +
> > drivers/pinctrl/Makefile | 1 +
> > drivers/pinctrl/pinctrl-k230.c | 674 ++++++++++++++++++
> > 7 files changed, 1151 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/pinctrl/canaan,k230-pinctrl.yaml
> > create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi
> > create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.h
> > create mode 100644 drivers/pinctrl/pinctrl-k230.c
> >
>
> lost base commit and prerequisite patch id here:
>
> base-commit: 0eea987088a22d73d81e968de7347cdc7e594f72
> prerequisite-patch-id: 740cbeb9fc3f3e3fd30df4914cd31e9eb148a581
> prerequisite-patch-id: b5cc919a7e8e2f852569d5918944dbe4f21e6912
> prerequisite-patch-id: 554cb838b7264109437359e88443cc3497ed344c
I don't have the ability to convert those to something I can understand,
is
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/log/?h=k230-basic
effectively the basis for your series?
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 0/3] Add initial support for Canaan Kendryte K230 pinctrl
2024-09-15 14:21 [PATCH 0/3] Add initial support for Canaan Kendryte K230 pinctrl Ze Huang
2024-09-15 15:22 ` Ze Huang
@ 2024-09-15 22:56 ` Inochi Amaoto
2024-09-16 3:58 ` Ze Huang
1 sibling, 1 reply; 6+ messages in thread
From: Inochi Amaoto @ 2024-09-15 22:56 UTC (permalink / raw)
To: Ze Huang, linus.walleij, robh, krzk+dt, conor+dt, paul.walmsley,
palmer, aou, conor
Cc: devicetree, dlan, zhangmeng.kevin, linux-kernel, jesse, cyy,
inochiama, jszhang, kevin.z.m
On Sun, Sep 15, 2024 at 10:21:24PM GMT, Ze Huang wrote:
> This patch series introduces support for the pinctrl driver of the Canaan
> K230 SoC. The K230 SoC features 64 IO pins, each of which can be configured
> for up to five different functions.
>
> The controller manages the entire pin configuration and multiplexing
> through a single register, which control features such as schmitt trigger,
> drive strength, bias pull-up/down, input/output enable, power source, and
> mux mode.
>
> The changes have been tested on the K230 development board.
>
> The pin function definition can be found here [1], and most of the DTS data
> was converted from the vendor's code [2].
>
> Link: https://developer.canaan-creative.com/k230/dev/_downloads/a53655a81951bc8a440ae647be286e75/K230_PINOUT_V1.1_20230321.xlsx [1]
> Link: https://github.com/kendryte/k230_sdk/blob/main/src/little/uboot/arch/riscv/dts/k230_canmv.dts [2]
>
> Ze Huang (3):
> dt-bindings: pinctrl: Add support for canaan,k230 SoC
> pinctrl: canaan: Add support for k230 SoC
> riscv: dts: canaan: Add k230's pinctrl node
>
> .../bindings/pinctrl/canaan,k230-pinctrl.yaml | 128 ++++
> arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi | 318 +++++++++
> arch/riscv/boot/dts/canaan/k230-pinctrl.h | 18 +
> arch/riscv/boot/dts/canaan/k230.dtsi | 2 +
> drivers/pinctrl/Kconfig | 10 +
> drivers/pinctrl/Makefile | 1 +
> drivers/pinctrl/pinctrl-k230.c | 674 ++++++++++++++++++
> 7 files changed, 1151 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/canaan,k230-pinctrl.yaml
> create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi
> create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.h
> create mode 100644 drivers/pinctrl/pinctrl-k230.c
>
> --
> 2.46.1
You should send your patched as a thread. I think you
forgot to set (or set wrong) in-reply-to?
Regards,
Inochi
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 0/3] Add initial support for Canaan Kendryte K230 pinctrl
2024-09-15 19:35 ` Conor Dooley
@ 2024-09-16 3:50 ` Ze Huang
0 siblings, 0 replies; 6+ messages in thread
From: Ze Huang @ 2024-09-16 3:50 UTC (permalink / raw)
To: Conor Dooley
Cc: linus.walleij, robh, krzk+dt, conor+dt, paul.walmsley, palmer,
aou, cyy, jesse, jszhang, inochiama, zhangmeng.kevin, kevin.z.m,
devicetree, linux-riscv, linux-kernel
On 9/16/24 3:35 AM, Conor Dooley wrote:
> On Sun, Sep 15, 2024 at 11:22:16PM +0800, Ze Huang wrote:
>> On 9/15/24 10:21 PM, Ze Huang wrote:
>>> This patch series introduces support for the pinctrl driver of the Canaan
>>> K230 SoC. The K230 SoC features 64 IO pins, each of which can be configured
>>> for up to five different functions.
>>>
>>> The controller manages the entire pin configuration and multiplexing
>>> through a single register, which control features such as schmitt trigger,
>>> drive strength, bias pull-up/down, input/output enable, power source, and
>>> mux mode.
>>>
>>> The changes have been tested on the K230 development board.
>>>
>>> The pin function definition can be found here [1], and most of the DTS data
>>> was converted from the vendor's code [2].
>>>
>>> Link: https://developer.canaan-creative.com/k230/dev/_downloads/a53655a81951bc8a440ae647be286e75/K230_PINOUT_V1.1_20230321.xlsx [1]
>>> Link: https://github.com/kendryte/k230_sdk/blob/main/src/little/uboot/arch/riscv/dts/k230_canmv.dts [2]
>>>
>>> Ze Huang (3):
>>> dt-bindings: pinctrl: Add support for canaan,k230 SoC
>>> pinctrl: canaan: Add support for k230 SoC
>>> riscv: dts: canaan: Add k230's pinctrl node
>>>
>>> .../bindings/pinctrl/canaan,k230-pinctrl.yaml | 128 ++++
>>> arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi | 318 +++++++++
>>> arch/riscv/boot/dts/canaan/k230-pinctrl.h | 18 +
>>> arch/riscv/boot/dts/canaan/k230.dtsi | 2 +
>>> drivers/pinctrl/Kconfig | 10 +
>>> drivers/pinctrl/Makefile | 1 +
>>> drivers/pinctrl/pinctrl-k230.c | 674 ++++++++++++++++++
>>> 7 files changed, 1151 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/pinctrl/canaan,k230-pinctrl.yaml
>>> create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi
>>> create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.h
>>> create mode 100644 drivers/pinctrl/pinctrl-k230.c
>>>
>> lost base commit and prerequisite patch id here:
>>
>> base-commit: 0eea987088a22d73d81e968de7347cdc7e594f72
>> prerequisite-patch-id: 740cbeb9fc3f3e3fd30df4914cd31e9eb148a581
>> prerequisite-patch-id: b5cc919a7e8e2f852569d5918944dbe4f21e6912
>> prerequisite-patch-id: 554cb838b7264109437359e88443cc3497ed344c
> I don't have the ability to convert those to something I can understand,
> is
> https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/log/?h=k230-basic
> effectively the basis for your series?
Thank you for your understanding; that is indeed the basis for series.
base-commit: 0eea987088a22d73d81e968de7347cdc7e594f72
prerequisite-patch-id: 2401703b57448c9ea2c3dc7650b4502491a28944
prerequisite-patch-id: 50ccf1104191cdf22f9077880d3dc781b190a3c8
prerequisite-patch-id: f8b983b301d0c14f1448b9e4c321262a509e061e
prerequisite-patch-id: ced4a01ccd8ddab2fd308d543ddf47bd1641518a
prerequisite-patch-id: c2144cf468c57b856830a61615ba6ba501e8ec58
prerequisite-patch-id: 704efc6e76814e1877748959d7319d558c8386c1
Link:
https://lore.kernel.org/all/tencent_22BA0425B4DF1CA1713B62E4423C1BFBF809@qq.com/
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 0/3] Add initial support for Canaan Kendryte K230 pinctrl
2024-09-15 22:56 ` Inochi Amaoto
@ 2024-09-16 3:58 ` Ze Huang
0 siblings, 0 replies; 6+ messages in thread
From: Ze Huang @ 2024-09-16 3:58 UTC (permalink / raw)
To: Inochi Amaoto, linus.walleij, robh, krzk+dt, conor+dt,
paul.walmsley, palmer, aou, conor
Cc: devicetree, linux-kernel, jesse, cyy, inochiama, jszhang,
kevin.z.m
On 9/16/24 6:56 AM, Inochi Amaoto wrote:
> On Sun, Sep 15, 2024 at 10:21:24PM GMT, Ze Huang wrote:
>> This patch series introduces support for the pinctrl driver of the Canaan
>> K230 SoC. The K230 SoC features 64 IO pins, each of which can be configured
>> for up to five different functions.
>>
>> The controller manages the entire pin configuration and multiplexing
>> through a single register, which control features such as schmitt trigger,
>> drive strength, bias pull-up/down, input/output enable, power source, and
>> mux mode.
>>
>> The changes have been tested on the K230 development board.
>>
>> The pin function definition can be found here [1], and most of the DTS data
>> was converted from the vendor's code [2].
>>
>> Link: https://developer.canaan-creative.com/k230/dev/_downloads/a53655a81951bc8a440ae647be286e75/K230_PINOUT_V1.1_20230321.xlsx [1]
>> Link: https://github.com/kendryte/k230_sdk/blob/main/src/little/uboot/arch/riscv/dts/k230_canmv.dts [2]
>>
>> Ze Huang (3):
>> dt-bindings: pinctrl: Add support for canaan,k230 SoC
>> pinctrl: canaan: Add support for k230 SoC
>> riscv: dts: canaan: Add k230's pinctrl node
>>
>> .../bindings/pinctrl/canaan,k230-pinctrl.yaml | 128 ++++
>> arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi | 318 +++++++++
>> arch/riscv/boot/dts/canaan/k230-pinctrl.h | 18 +
>> arch/riscv/boot/dts/canaan/k230.dtsi | 2 +
>> drivers/pinctrl/Kconfig | 10 +
>> drivers/pinctrl/Makefile | 1 +
>> drivers/pinctrl/pinctrl-k230.c | 674 ++++++++++++++++++
>> 7 files changed, 1151 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pinctrl/canaan,k230-pinctrl.yaml
>> create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.dtsi
>> create mode 100644 arch/riscv/boot/dts/canaan/k230-pinctrl.h
>> create mode 100644 drivers/pinctrl/pinctrl-k230.c
>>
>> --
>> 2.46.1
> You should send your patched as a thread. I think you
> forgot to set (or set wrong) in-reply-to?
Thank you for pointing that out. I apologize for the oversight. I will
resend the patch series as a thread and ensure that the in-reply-to headers
are set correctly.
Thank you for your patience.
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2024-09-16 3:59 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-09-15 14:21 [PATCH 0/3] Add initial support for Canaan Kendryte K230 pinctrl Ze Huang
2024-09-15 15:22 ` Ze Huang
2024-09-15 19:35 ` Conor Dooley
2024-09-16 3:50 ` Ze Huang
2024-09-15 22:56 ` Inochi Amaoto
2024-09-16 3:58 ` Ze Huang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox