From: Tony Nguyen <anthony.l.nguyen@intel.com>
To: davem@davemloft.net, kuba@kernel.org, pabeni@redhat.com,
edumazet@kernel.org, andrew+netdev@lunn.ch,
netdev@vger.kernel.org
Cc: Aleksandr Loktionov <aleksandr.loktionov@intel.com>,
anthony.l.nguyen@intel.com, grzegorz.nitka@intel.com,
marcin.szycik@intel.com, jacob.e.keller@intel.com,
przemyslaw.korba@intel.com, xiongwm2026@163.com,
ynorov@nvidia.com, przemyslaw.kitszel@intel.com,
horms@kernel.org, Alexander Nowlin <alexander.nowlin@intel.com>
Subject: [PATCH net-next 04/10] ice: increase OICR interrupt moderation rate to 20K interrupts/sec
Date: Tue, 29 Sep 2026 15:41:44 -0700 [thread overview]
Message-ID: <20260929224153.1455466-5-anthony.l.nguyen@intel.com> (raw)
In-Reply-To: <20260929224153.1455466-1-anthony.l.nguyen@intel.com>
From: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
The miscellaneous interrupt cause (OICR) is throttled to 8K
interrupts per second (124 us minimum spacing). This interrupt
handles VF mailbox messages and Tx timestamps, so the low rate
imposes a minimum latency floor on both use-cases.
Raise the rate to 20K interrupts per second (50 us minimum
spacing) to allow lower latency handling for Tx timestamp
bursts and high VF message rates.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
drivers/net/ethernet/intel/ice/ice_main.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_main.c b/drivers/net/ethernet/intel/ice/ice_main.c
index 707c7431b91a..73f69d453542 100644
--- a/drivers/net/ethernet/intel/ice/ice_main.c
+++ b/drivers/net/ethernet/intel/ice/ice_main.c
@@ -3428,7 +3428,7 @@ static int ice_req_irq_msix_misc(struct ice_pf *pf)
((pf->ll_ts_irq.index + pf_intr_start_offset) &
PFINT_SB_CTL_MSIX_INDX_M) | PFINT_SB_CTL_CAUSE_ENA_M);
wr32(hw, GLINT_ITR(ICE_RX_ITR, pf->oicr_irq.index),
- ITR_REG_ALIGN(ICE_ITR_8K) >> ICE_ITR_GRAN_S);
+ ITR_REG_ALIGN(ICE_ITR_20K) >> ICE_ITR_GRAN_S);
ice_flush(hw);
ice_irq_dynamic_ena(hw, NULL, NULL);
--
2.47.1
next prev parent reply other threads:[~2026-09-29 22:42 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-29 22:41 [PATCH net-next 00/10][pull request] Intel Wired LAN Driver Updates 2026-09-29 (ice) Tony Nguyen
2026-09-29 22:41 ` [PATCH net-next 01/10] ice: reduce loglevel to debug for 'Can't delete DSCP' message Tony Nguyen
2026-10-02 20:03 ` netdev-bot+sashiko
2026-09-29 22:41 ` [PATCH net-next 02/10] ice: use ice_fill_eth_hdr() in ice_fill_sw_rule() Tony Nguyen
2026-09-29 22:41 ` [PATCH net-next 03/10] ice: reorder ice_flash_info fields to eliminate padding Tony Nguyen
2026-09-29 22:41 ` Tony Nguyen [this message]
2026-10-02 20:03 ` [PATCH net-next 04/10] ice: increase OICR interrupt moderation rate to 20K interrupts/sec netdev-bot+sashiko
2026-09-29 22:41 ` [PATCH net-next 05/10] ice: use inline helpers instead of memcmp() for IPv6 mask checks in ice_ethtool_fdir Tony Nguyen
2026-10-02 20:03 ` netdev-bot+sashiko
2026-09-29 22:41 ` [PATCH net-next 06/10] ice: add rx timestamp tracepoint for debugging Tony Nguyen
2026-09-29 22:41 ` [PATCH net-next 07/10] ice: parser: use kcalloc for table allocation Tony Nguyen
2026-10-02 20:03 ` netdev-bot+sashiko
2026-09-29 22:41 ` [PATCH net-next 08/10] ice: simplify ice_pf_state_is_nominal() Tony Nguyen
2026-10-02 20:03 ` netdev-bot+sashiko
2026-09-29 22:41 ` [PATCH net-next 09/10] ice: drop pf == NULL check in ice_pf_state_is_nominal() Tony Nguyen
2026-09-29 22:41 ` [PATCH net-next 10/10] ice: simplify ice_vc_dis_qs_msg() a little Tony Nguyen
2026-10-02 20:03 ` netdev-bot+sashiko
2026-10-06 1:00 ` [PATCH net-next 00/10][pull request] Intel Wired LAN Driver Updates 2026-09-29 (ice) patchwork-bot+netdevbpf
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260929224153.1455466-5-anthony.l.nguyen@intel.com \
--to=anthony.l.nguyen@intel.com \
--cc=aleksandr.loktionov@intel.com \
--cc=alexander.nowlin@intel.com \
--cc=andrew+netdev@lunn.ch \
--cc=davem@davemloft.net \
--cc=edumazet@kernel.org \
--cc=grzegorz.nitka@intel.com \
--cc=horms@kernel.org \
--cc=jacob.e.keller@intel.com \
--cc=kuba@kernel.org \
--cc=marcin.szycik@intel.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=przemyslaw.kitszel@intel.com \
--cc=przemyslaw.korba@intel.com \
--cc=xiongwm2026@163.com \
--cc=ynorov@nvidia.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox