[PATCH] Add Fujitsu 1000base-SX PCI ID to tg3

[PATCH] Add Fujitsu 1000base-SX PCI ID to tg3

[Meelis Roos]

This patch adds the PCI ID of Fujitsu 1000base-SX NIC to tg3 driver. 
Tested to detect the card, MAC and serdes, not tested with link at the 
moment since I have no fiber switch here. I did not add new constants to 
the pci_ids.h header file since these constants are used only here.

Signed-off-by: Meelis Roos <mroos@linux.ee>

diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
index 7a5daef..7b1901e 100644
--- a/drivers/net/tg3.c
+++ b/drivers/net/tg3.c
@@ -273,6 +273,7 @@ static DEFINE_PCI_DEVICE_TABLE(tg3_pci_tbl) = {
 	{PCI_DEVICE(PCI_VENDOR_ID_ALTIMA, PCI_DEVICE_ID_ALTIMA_AC1003)},
 	{PCI_DEVICE(PCI_VENDOR_ID_ALTIMA, PCI_DEVICE_ID_ALTIMA_AC9100)},
 	{PCI_DEVICE(PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_TIGON3)},
+	{PCI_DEVICE(0x10cf, 0x11a2)}, /* Fujitsu 1000base-SX with BCM5703SKHB */
 	{}
 };
 

-- 
Meelis Roos (mroos@linux.ee)

Re: [PATCH] Add Fujitsu 1000base-SX PCI ID to tg3

[Matt Carlson]

On Wed, May 25, 2011 at 08:43:47AM -0700, Meelis Roos wrote:
> This patch adds the PCI ID of Fujitsu 1000base-SX NIC to tg3 driver. 
> Tested to detect the card, MAC and serdes, not tested with link at the 
> moment since I have no fiber switch here. I did not add new constants to 
> the pci_ids.h header file since these constants are used only here.
> 
> Signed-off-by: Meelis Roos <mroos@linux.ee>
> 
> diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
> index 7a5daef..7b1901e 100644
> --- a/drivers/net/tg3.c
> +++ b/drivers/net/tg3.c
> @@ -273,6 +273,7 @@ static DEFINE_PCI_DEVICE_TABLE(tg3_pci_tbl) = {
>  	{PCI_DEVICE(PCI_VENDOR_ID_ALTIMA, PCI_DEVICE_ID_ALTIMA_AC1003)},
>  	{PCI_DEVICE(PCI_VENDOR_ID_ALTIMA, PCI_DEVICE_ID_ALTIMA_AC9100)},
>  	{PCI_DEVICE(PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_TIGON3)},
> +	{PCI_DEVICE(0x10cf, 0x11a2)}, /* Fujitsu 1000base-SX with BCM5703SKHB */
>  	{}
>  };

I don't have any problems with the patch, but before we integrate it,
can we make sure it passes traffic?  I'd hate to add support for a
device and later find out it doesn't work.

Re: [PATCH] Add Fujitsu 1000base-SX PCI ID to tg3

[Meelis Roos]

> > This patch adds the PCI ID of Fujitsu 1000base-SX NIC to tg3 driver. 
> > Tested to detect the card, MAC and serdes, not tested with link at the 
> > moment since I have no fiber switch here. I did not add new constants to 
> > the pci_ids.h header file since these constants are used only here.
> > 
> > Signed-off-by: Meelis Roos <mroos@linux.ee>
> > 
> > diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
> > index 7a5daef..7b1901e 100644
> > --- a/drivers/net/tg3.c
> > +++ b/drivers/net/tg3.c
> > @@ -273,6 +273,7 @@ static DEFINE_PCI_DEVICE_TABLE(tg3_pci_tbl) = {
> >  	{PCI_DEVICE(PCI_VENDOR_ID_ALTIMA, PCI_DEVICE_ID_ALTIMA_AC1003)},
> >  	{PCI_DEVICE(PCI_VENDOR_ID_ALTIMA, PCI_DEVICE_ID_ALTIMA_AC9100)},
> >  	{PCI_DEVICE(PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_TIGON3)},
> > +	{PCI_DEVICE(0x10cf, 0x11a2)}, /* Fujitsu 1000base-SX with BCM5703SKHB */
> >  	{}
> >  };
> 
> I don't have any problems with the patch, but before we integrate it,
> can we make sure it passes traffic?  I'd hate to add support for a
> device and later find out it doesn't work.

Checked with direct link to another NIC, link came up.

[   99.067432] tg3 0000:01:0b.0: eth1: Link is up at 1000 Mbps, full duplex
[   99.067662] tg3 0000:01:0b.0: eth1: Flow control is on for TX and on for RX 

I can also see DHCP requests from one interface on the other with 
tcpdump, so data gets also through. Seems to work.

-- 
Meelis Roos (mroos@linux.ee)