[net-next v2 0/3] Add motorcomm 8531s set ds func and 8522 driver

[net-next v2 0/3] Add motorcomm 8531s set ds func and 8522 driver

[Minda Chen]

This patch is for Starfive JHB100 EVB board. JHB100  contain
1 RGMII/RMII and 1 RMII synopsys GMAC cores. In the EVB board, RGMII
interface connect with YT8531s Ethernet PHY. RMII interface connect
with YT8522 ethernet PHY. So patch 1-2 is for RGMII interface
patch 3 is RMII is for RMII interface.

JHB100 is a Starfive new RISC-V SoC for datacenter BMC (BaseBoard
Managent Controller). Similar with Aspeed 27x0.

The JHB100 minimal system upstream is in progress:
https://patchwork.kernel.org/project/linux-riscv/cover/20260403054945.467700-1-changhuang.liang@starfivetech.com/

The patch base in V7.0-rc5

The change list:
v2:
1. patch1 move mdio lock out from  yt8531_set_ds().
2. patch2 changed to phy_interface_is_rgmii().

Minda Chen (3):
  net: phy: motorcomm: move mdio lock out from yt8531_set_ds()
  net: motorcomm: phy: set drive strength in 8531s RGMII case
  net: phy: motorcomm: Add YT8522 100M RMII PHY support

 drivers/net/phy/motorcomm.c | 77 ++++++++++++++++++++++++++++++++-----
 1 file changed, 67 insertions(+), 10 deletions(-)


base-commit: c369299895a591d96745d6492d4888259b004a9e
-- 
2.17.1

[net-next v2 1/3] net: phy: motorcomm: move mdio lock out from yt8531_set_ds()

[Minda Chen]

yt8531_set_ds() default set register with mdio lock and only called
with YT8531 PHY. But new type YT8531s support RGMII and has the same
pin strength setting with YT8531, YT8531s need to call yt8531_set_ds()
setting pin drive strength. But YT8531s config init function
yt8521_config_init() already get the mdio lock with phy_select_page().
If calling yt8521_config_init() with mdio lock will cause dead lock.

Need to get the lock before calling yt8531_get_ds() and move mdio
lock out from it can solve this issue.

Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
---
 drivers/net/phy/motorcomm.c | 23 ++++++++++++++---------
 1 file changed, 14 insertions(+), 9 deletions(-)

diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index 4d62f7b36212..c66804537aa2 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -974,7 +974,8 @@ static u32 yt8531_get_ldo_vol(struct phy_device *phydev)
 {
 	u32 val;
 
-	val = ytphy_read_ext_with_lock(phydev, YT8521_CHIP_CONFIG_REG);
+	val = ytphy_read_ext(phydev, YT8521_CHIP_CONFIG_REG);
+
 	val = FIELD_GET(YT8531_RGMII_LDO_VOL_MASK, val);
 
 	return val <= YT8531_LDO_VOL_1V8 ? val : YT8531_LDO_VOL_1V8;
@@ -1010,10 +1011,11 @@ static int yt8531_set_ds(struct phy_device *phydev)
 		ds = YT8531_RGMII_RX_DS_DEFAULT;
 	}
 
-	ret = ytphy_modify_ext_with_lock(phydev,
-					 YTPHY_PAD_DRIVE_STRENGTH_REG,
-					 YT8531_RGMII_RXC_DS_MASK,
-					 FIELD_PREP(YT8531_RGMII_RXC_DS_MASK, ds));
+	ret = ytphy_modify_ext(phydev,
+			       YTPHY_PAD_DRIVE_STRENGTH_REG,
+			       YT8531_RGMII_RXC_DS_MASK,
+			       FIELD_PREP(YT8531_RGMII_RXC_DS_MASK, ds));
+
 	if (ret < 0)
 		return ret;
 
@@ -1033,10 +1035,11 @@ static int yt8531_set_ds(struct phy_device *phydev)
 	ds_field_low = FIELD_GET(GENMASK(1, 0), ds);
 	ds_field_low = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW_MASK, ds_field_low);
 
-	ret = ytphy_modify_ext_with_lock(phydev,
-					 YTPHY_PAD_DRIVE_STRENGTH_REG,
-					 YT8531_RGMII_RXD_DS_LOW_MASK | YT8531_RGMII_RXD_DS_HI_MASK,
-					 ds_field_low | ds_field_hi);
+	ret = ytphy_modify_ext(phydev,
+			       YTPHY_PAD_DRIVE_STRENGTH_REG,
+			       YT8531_RGMII_RXD_DS_LOW_MASK | YT8531_RGMII_RXD_DS_HI_MASK,
+			       ds_field_low | ds_field_hi);
+
 	if (ret < 0)
 		return ret;
 
@@ -1826,7 +1829,9 @@ static int yt8531_config_init(struct phy_device *phydev)
 			return ret;
 	}
 
+	phy_lock_mdio_bus(phydev);
 	ret = yt8531_set_ds(phydev);
+	phy_unlock_mdio_bus(phydev);
 	if (ret < 0)
 		return ret;
 
-- 
2.17.1

[net-next v2 2/3] net: motorcomm: phy: set drive strength in 8531s RGMII case

[Minda Chen]

Set RXD and RX CLK pin drive strength while in 8531s RGMII
case.

Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
---
 drivers/net/phy/motorcomm.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index c66804537aa2..ebc24f51e626 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -1698,6 +1698,11 @@ static int yt8521_config_init(struct phy_device *phydev)
 		if (ret < 0)
 			goto err_restore_page;
 	}
+
+	if (phydev->drv->phy_id == PHY_ID_YT8531S &&
+	    phy_interface_is_rgmii(phydev))
+		ret = yt8531_set_ds(phydev);
+
 err_restore_page:
 	return phy_restore_page(phydev, old_page, ret);
 }
-- 
2.17.1

[net-next v2 3/3] net: phy: motorcomm: Add YT8522 100M RMII PHY support

[Minda Chen]

Add YT8522 100M RMII ethernet PHY base driver support, including
PHY ID and base config init function.

Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
---
 drivers/net/phy/motorcomm.c | 49 ++++++++++++++++++++++++++++++++++++-
 1 file changed, 48 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index ebc24f51e626..13d57aba5487 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Motorcomm 8511/8521/8531/8531S/8821 PHY driver.
+ * Motorcomm 8511/8521/8522/8531/8531S/8821 PHY driver.
  *
  * Author: Peter Geis <pgwipeout@gmail.com>
  * Author: Frank <Frank.Sae@motor-comm.com>
@@ -14,6 +14,7 @@
 
 #define PHY_ID_YT8511		0x0000010a
 #define PHY_ID_YT8521		0x0000011a
+#define PHY_ID_YT8522		0x4f51e928
 #define PHY_ID_YT8531		0x4f51e91b
 #define PHY_ID_YT8531S		0x4f51e91a
 #define PHY_ID_YT8821		0x4f51ea19
@@ -227,6 +228,13 @@
 #define YT8521_LED_100_ON_EN			BIT(5)
 #define YT8521_LED_10_ON_EN			BIT(4)
 
+#define YT8522_EXTREG_SLEEP_CONTROL		0x2027
+#define YT8522_EN_SLEEP_SW			15
+
+#define YT8522_EXTENDED_COMBO_CTRL		0x4000
+#define YT8522_RXDV_SEL				BIT(4)
+#define YT8522_RMII_EN				BIT(1)
+
 #define YTPHY_MISC_CONFIG_REG			0xA006
 #define YTPHY_MCR_FIBER_SPEED_MASK		BIT(0)
 #define YTPHY_MCR_FIBER_1000BX			(0x1 << 0)
@@ -1843,6 +1851,36 @@ static int yt8531_config_init(struct phy_device *phydev)
 	return 0;
 }
 
+static int yt8522_config_init(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	int ret, val;
+
+	val = ytphy_read_ext_with_lock(phydev, YT8522_EXTENDED_COMBO_CTRL);
+	if (val < 0)
+		return val;
+
+	if (val & YT8522_RMII_EN) {
+		val |= YT8522_RXDV_SEL;
+		ret = ytphy_write_ext_with_lock(phydev,
+						YT8522_EXTENDED_COMBO_CTRL,
+						val);
+		if (ret < 0)
+			return ret;
+	}
+
+	if (of_property_read_bool(node, "motorcomm,auto-sleep-disabled")) {
+		/* disable auto sleep */
+		ret = ytphy_modify_ext_with_lock(phydev,
+						 YT8522_EXTREG_SLEEP_CONTROL,
+						 YT8522_EN_SLEEP_SW, 0);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
 /**
  * yt8531_link_change_notify() - Adjust the tx clock direction according to
  * the current speed and dts config.
@@ -3052,6 +3090,14 @@ static struct phy_driver motorcomm_phy_drvs[] = {
 		.led_hw_control_set = yt8521_led_hw_control_set,
 		.led_hw_control_get = yt8521_led_hw_control_get,
 	},
+	{
+		PHY_ID_MATCH_EXACT(PHY_ID_YT8522),
+		.name		= "YT8522 100 Megabit Ethernet",
+		.config_aneg	= genphy_config_aneg,
+		.config_init	= yt8522_config_init,
+		.suspend	= genphy_suspend,
+		.resume		= genphy_resume,
+	},
 	{
 		PHY_ID_MATCH_EXACT(PHY_ID_YT8531),
 		.name		= "YT8531 Gigabit Ethernet",
@@ -3112,6 +3158,7 @@ MODULE_LICENSE("GPL");
 static const struct mdio_device_id __maybe_unused motorcomm_tbl[] = {
 	{ PHY_ID_MATCH_EXACT(PHY_ID_YT8511) },
 	{ PHY_ID_MATCH_EXACT(PHY_ID_YT8521) },
+	{ PHY_ID_MATCH_EXACT(PHY_ID_YT8522) },
 	{ PHY_ID_MATCH_EXACT(PHY_ID_YT8531) },
 	{ PHY_ID_MATCH_EXACT(PHY_ID_YT8531S) },
 	{ PHY_ID_MATCH_EXACT(PHY_ID_YT8821) },
-- 
2.17.1

Re: [net-next v2 0/3] Add motorcomm 8531s set ds func and 8522 driver

[Andrew Lunn]

On Wed, Apr 22, 2026 at 04:32:52PM +0800, Minda Chen wrote:
> This patch is for Starfive JHB100 EVB board. JHB100  contain
> 1 RGMII/RMII and 1 RMII synopsys GMAC cores. In the EVB board, RGMII
> interface connect with YT8531s Ethernet PHY. RMII interface connect
> with YT8522 ethernet PHY. So patch 1-2 is for RGMII interface
> patch 3 is RMII is for RMII interface.
> 
> JHB100 is a Starfive new RISC-V SoC for datacenter BMC (BaseBoard
> Managent Controller). Similar with Aspeed 27x0.
> 
> The JHB100 minimal system upstream is in progress:
> https://patchwork.kernel.org/project/linux-riscv/cover/20260403054945.467700-1-changhuang.liang@starfivetech.com/

Please take a read of sections 1.3 and 1.4 of:

https://www.kernel.org/doc/html/latest/process/maintainer-netdev.html

    Andrew

---
pw-bot: cr

Re: [net-next v2 0/3] Add motorcomm 8531s set ds func and 8522 driver

[Minda Chen]

> 
> On Wed, Apr 22, 2026 at 04:32:52PM +0800, Minda Chen wrote:
> > This patch is for Starfive JHB100 EVB board. JHB100  contain
> > 1 RGMII/RMII and 1 RMII synopsys GMAC cores. In the EVB board, RGMII
> > interface connect with YT8531s Ethernet PHY. RMII interface connect
> > with YT8522 ethernet PHY. So patch 1-2 is for RGMII interface patch 3
> > is RMII is for RMII interface.
> >
> > JHB100 is a Starfive new RISC-V SoC for datacenter BMC (BaseBoard
> > Managent Controller). Similar with Aspeed 27x0.
> >
> > The JHB100 minimal system upstream is in progress:
> > https://patchwork.kernel.org/project/linux-riscv/cover/20260403054945.
> > 467700-1-changhuang.liang@starfivetech.com/
> 
> Please take a read of sections 1.3 and 1.4 of:
> 
> https://www.kernel.org/doc/html/latest/process/maintainer-netdev.html
> 
>     Andrew
> 
> ---
> pw-bot: cr

I am sorry about the "net-next" in merge window