* Re: [PATCH net-next 0/3] ptp: feature enhancements
From: David Miller @ 2011-09-26 20:04 UTC (permalink / raw)
To: richardcochran; +Cc: netdev
In-Reply-To: <cover.1316518332.git.richard.cochran@omicron.at>
From: Richard Cochran <richardcochran@gmail.com>
Date: Tue, 20 Sep 2011 13:43:13 +0200
> This series adds one driver specific enhancement and one new feature
> to the PTP Hardware Clock subsystem. The first patch enables more of
> the phyter's IO capabilities. The second patch introduces PTP one-step
> support for Sync messages at the driver level. The third patch
> implements the one-step flag in the phyter.
>
> Richard Cochran (3):
> dp83640: enable six external events and one periodic output
> net: introduce ptp one step time stamp mode for sync packets
> dp83640: add time stamp insertion for sync messages
All applied to net-next, thanks.
Could you please add a test at the point where we pull in the
->tx_type value from the user, to make sure it is one of the
validly defined HWTSTAMP_TX_FOO values?
Thanks.
^ permalink raw reply
* Re: Bridge stays down until a port is added
From: Stephen Hemminger @ 2011-09-26 20:05 UTC (permalink / raw)
To: Nicolas de Pesloüan; +Cc: Marc Haber, netdev
In-Reply-To: <4E80DA4D.3090404@gmail.com>
On Mon, 26 Sep 2011 22:02:21 +0200
Nicolas de Pesloüan <nicolas.2p.debian@gmail.com> wrote:
> Le 26/09/2011 17:47, Stephen Hemminger a écrit :
> > The root of this whole problem is really that IPv6 reports addresses
> > in a tentative state to applications that can not be passed to the bind() system call.
> > For most cases, this problem never happens because the tentative addresses are
> > resolved by Duplicate Address Detection before the application starts. But
> > I have seen (and fixed) this happen before this whole discussion started.
> >
> > 1. The problem is not unique to bridges. It happens with bridge, macvtap,
> > even on wireless networks where the device is available but carrier is
> > not asserted.
> >
> > 2. Any change to what the kernel does (like not reporting tentative addresses)
> > would break applications even worse.
> >
> > 3. When the bridge was always reporting carrier, it was in effect breaking
> > IPv6 Duplicate Address Detection. And that is bad.
>
> Stephen,
>
> What do you think about a generic per-interface option that would cause bind() to accept tentative
> address hold by a particular interface? This of course violate IPv6 principle, but we are talking
> about interfaces that are unable to do DAD, either permanently or until something happens on the
> underlying device.
>
> echo 1 > /sys/class/net/br0/allow_bind_on_tentative_address
> echo 1 > /sys/class/net/dummy0/allow_bind_on_tentative_address
> echo 1 > /sys/class/net/wlan0/allow_bind_on_tentative_address
> and so on...
>
> And we may possibly automatically reset this option to 0 if DAD eventually causes the address to be
> considered duplicate.
The issue is that if DAD rejects a duplicate, the socket is dead and application is
out of luck.
Has anyone looked at this issue in relation to systemd which does early
opportunistic binding of services?
^ permalink raw reply
* [PATCH] ehea: Remove sleep at .ndo_get_stats
From: brenohl @ 2011-09-26 20:11 UTC (permalink / raw)
To: eric.dumazet; +Cc: davem, netdev, Breno Leitao
In-Reply-To: <1317066179.2796.9.camel@edumazet-laptop>
Currently ehea ndo_get_stats can sleep in two places, in a hcall
and in a GFP_KERNEL alloc, which is not correct.
This patch creates a delayed workqueue that grabs the information each 1
sec from the hardware, and place it into the device structure, so that,
.ndo_get_stats quickly returns the device structure statistics block.
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
---
drivers/net/ethernet/ibm/ehea/ehea.h | 1 +
drivers/net/ethernet/ibm/ehea/ehea_main.c | 59 +++++++++++++++++-----------
2 files changed, 37 insertions(+), 23 deletions(-)
diff --git a/drivers/net/ethernet/ibm/ehea/ehea.h b/drivers/net/ethernet/ibm/ehea/ehea.h
index 7dd5e6a..0b8e6a9 100644
--- a/drivers/net/ethernet/ibm/ehea/ehea.h
+++ b/drivers/net/ethernet/ibm/ehea/ehea.h
@@ -459,6 +459,7 @@ struct ehea_port {
struct ehea_mc_list *mc_list; /* Multicast MAC addresses */
struct ehea_eq *qp_eq;
struct work_struct reset_task;
+ struct delayed_work stats_work;
struct mutex port_lock;
char int_aff_name[EHEA_IRQ_NAME_SIZE];
int allmulti; /* Indicates IFF_ALLMULTI state */
diff --git a/drivers/net/ethernet/ibm/ehea/ehea_main.c b/drivers/net/ethernet/ibm/ehea/ehea_main.c
index 583bcd3..c821cb6 100644
--- a/drivers/net/ethernet/ibm/ehea/ehea_main.c
+++ b/drivers/net/ethernet/ibm/ehea/ehea_main.c
@@ -331,16 +331,40 @@ static struct net_device_stats *ehea_get_stats(struct net_device *dev)
{
struct ehea_port *port = netdev_priv(dev);
struct net_device_stats *stats = &port->stats;
- struct hcp_ehea_port_cb2 *cb2;
- u64 hret, rx_packets, tx_packets, rx_bytes = 0, tx_bytes = 0;
+ u64 rx_packets = 0, tx_packets = 0, rx_bytes = 0, tx_bytes = 0;
int i;
- memset(stats, 0, sizeof(*stats));
+ for (i = 0; i < port->num_def_qps; i++) {
+ rx_packets += port->port_res[i].rx_packets;
+ rx_bytes += port->port_res[i].rx_bytes;
+ }
+
+ for (i = 0; i < port->num_def_qps + port->num_add_tx_qps; i++) {
+ tx_packets += port->port_res[i].tx_packets;
+ tx_bytes += port->port_res[i].tx_bytes;
+ }
+
+ stats->tx_packets = tx_packets;
+ stats->rx_bytes = rx_bytes;
+ stats->tx_bytes = tx_bytes;
+ stats->rx_packets = rx_packets;
+
+ return &port->stats;
+}
+
+static void ehea_update_stats(struct work_struct *work)
+{
+ struct ehea_port *port =
+ container_of(work, struct ehea_port, stats_work.work);
+ struct net_device *dev = port->netdev;
+ struct net_device_stats *stats = &port->stats;
+ struct hcp_ehea_port_cb2 *cb2;
+ u64 hret;
cb2 = (void *)get_zeroed_page(GFP_KERNEL);
if (!cb2) {
- netdev_err(dev, "no mem for cb2\n");
- goto out;
+ netdev_err(dev, "No mem for cb2. Some interface statistics were not updated\n");
+ goto resched;
}
hret = ehea_h_query_ehea_port(port->adapter->handle,
@@ -354,29 +378,13 @@ static struct net_device_stats *ehea_get_stats(struct net_device *dev)
if (netif_msg_hw(port))
ehea_dump(cb2, sizeof(*cb2), "net_device_stats");
- rx_packets = 0;
- for (i = 0; i < port->num_def_qps; i++) {
- rx_packets += port->port_res[i].rx_packets;
- rx_bytes += port->port_res[i].rx_bytes;
- }
-
- tx_packets = 0;
- for (i = 0; i < port->num_def_qps + port->num_add_tx_qps; i++) {
- tx_packets += port->port_res[i].tx_packets;
- tx_bytes += port->port_res[i].tx_bytes;
- }
-
- stats->tx_packets = tx_packets;
stats->multicast = cb2->rxmcp;
stats->rx_errors = cb2->rxuerr;
- stats->rx_bytes = rx_bytes;
- stats->tx_bytes = tx_bytes;
- stats->rx_packets = rx_packets;
out_herr:
free_page((unsigned long)cb2);
-out:
- return stats;
+resched:
+ schedule_delayed_work(&port->stats_work, msecs_to_jiffies(1000));
}
static void ehea_refill_rq1(struct ehea_port_res *pr, int index, int nr_of_wqes)
@@ -2651,6 +2659,7 @@ static int ehea_open(struct net_device *dev)
}
mutex_unlock(&port->port_lock);
+ schedule_delayed_work(&port->stats_work, msecs_to_jiffies(1000));
return ret;
}
@@ -2690,6 +2699,7 @@ static int ehea_stop(struct net_device *dev)
set_bit(__EHEA_DISABLE_PORT_RESET, &port->flags);
cancel_work_sync(&port->reset_task);
+ cancel_delayed_work_sync(&port->stats_work);
mutex_lock(&port->port_lock);
netif_stop_queue(dev);
port_napi_disable(port);
@@ -3235,10 +3245,12 @@ struct ehea_port *ehea_setup_single_port(struct ehea_adapter *adapter,
dev->features |= NETIF_F_LRO;
INIT_WORK(&port->reset_task, ehea_reset_port);
+ INIT_DELAYED_WORK(&port->stats_work, ehea_update_stats);
init_waitqueue_head(&port->swqe_avail_wq);
init_waitqueue_head(&port->restart_wq);
+ memset(&port->stats, 0, sizeof(struct net_device_stats));
ret = register_netdev(dev);
if (ret) {
pr_err("register_netdev failed. ret=%d\n", ret);
@@ -3278,6 +3290,7 @@ static void ehea_shutdown_single_port(struct ehea_port *port)
struct ehea_adapter *adapter = port->adapter;
cancel_work_sync(&port->reset_task);
+ cancel_delayed_work_sync(&port->stats_work);
unregister_netdev(port->netdev);
ehea_unregister_port(port);
kfree(port->mc_list);
--
1.7.1
^ permalink raw reply related
* Re: [PATCH] ehea: Remove sleep at .ndo_get_stats
From: Eric Dumazet @ 2011-09-26 20:28 UTC (permalink / raw)
To: brenohl; +Cc: davem, netdev
In-Reply-To: <1317067863-11706-1-git-send-email-brenohl@br.ibm.com>
Le lundi 26 septembre 2011 à 17:11 -0300, brenohl@br.ibm.com a écrit :
> Currently ehea ndo_get_stats can sleep in two places, in a hcall
> and in a GFP_KERNEL alloc, which is not correct.
> This patch creates a delayed workqueue that grabs the information each 1
> sec from the hardware, and place it into the device structure, so that,
> .ndo_get_stats quickly returns the device structure statistics block.
>
> Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
> ---
Seems good, thanks
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
^ permalink raw reply
* RE: [net-next] iproute2: Add new command to IP link to enable/disable VF spoof check
From: Christian Benvenuti (benve) @ 2011-09-26 20:54 UTC (permalink / raw)
To: Stephen Hemminger, Ben Hutchings
Cc: Rose, Gregory V, Kirsher, Jeffrey T, davem, netdev, gospo
In-Reply-To: <20110926094719.0cb6c296@nehalam.linuxnetplumber.net>
> -----Original Message-----
> From: netdev-owner@vger.kernel.org [mailto:netdev-
> owner@vger.kernel.org] On Behalf Of Stephen Hemminger
> Sent: Monday, September 26, 2011 9:47 AM
> To: Ben Hutchings
> Cc: Rose, Gregory V; Kirsher, Jeffrey T; davem@davemloft.net;
> netdev@vger.kernel.org; gospo@redhat.com
> Subject: Re: [net-next] iproute2: Add new command to IP link to
> enable/disable VF spoof check
>
> On Mon, 26 Sep 2011 17:41:59 +0100
> Ben Hutchings <bhutchings@solarflare.com> wrote:
>
> > On Mon, 2011-09-26 at 09:21 -0700, Rose, Gregory V wrote:
> > > > -----Original Message-----
> > > > From: Stephen Hemminger [mailto:shemminger@vyatta.com]
> > > > Sent: Sunday, September 25, 2011 10:24 AM
> > > > To: Kirsher, Jeffrey T
> > > > Cc: Rose, Gregory V; davem@davemloft.net;
netdev@vger.kernel.org;
> > > > gospo@redhat.com
> > > > Subject: Re: [net-next] iproute2: Add new command to IP link to
> > > > enable/disable VF spoof check
> > > >
> > > > On Sun, 25 Sep 2011 01:23:18 -0700
> > > > Jeff Kirsher <jeffrey.t.kirsher@intel.com> wrote:
> > > >
> > > > > From: Greg Rose <gregory.v.rose@intel.com>
> > > > >
> > > > > Add IP link command parsing for VF spoof checking
> enable/disable
> > > > >
> > > > > Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
> > > > > Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> > > >
> > > > See my comments about ABI compatibility. Can't just grow size of
> > > > structure.
> > > > Need to have new version of iproute work with older kernels.
> > >
> > > In this case I have no idea how to proceed. I'll go back and
stare
> at it some more.
> >
> > Where is this structure used on the wire? I just don't see it.
> >
> > If the modified iproute2 crashes on older kernels, that's presumably
> > because it's not correctly handling the case where IFLA_VF_SPOOFCHK
> is
> > missing. Nothing to do with the size of this structure.
>
> The proposed code is fine because the vf_info is not used by any code
> in iproute right now and I doubt that any other tools are using it
> either.
Does it mean that a Netlink interface becomes official (and backward
compatibility
should not be broken) only once iproute2 starts supporting it?
/Chris
^ permalink raw reply
* Re: Bridge stays down until a port is added
From: Ben Hutchings @ 2011-09-26 20:56 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: Nicolas de Pesloüan, Marc Haber, netdev
In-Reply-To: <20110926130507.1435d76b@nehalam.linuxnetplumber.net>
On Mon, 2011-09-26 at 13:05 -0700, Stephen Hemminger wrote:
> On Mon, 26 Sep 2011 22:02:21 +0200
> Nicolas de Pesloüan <nicolas.2p.debian@gmail.com> wrote:
[...]
> > What do you think about a generic per-interface option that would cause bind() to accept tentative
> > address hold by a particular interface? This of course violate IPv6 principle, but we are talking
> > about interfaces that are unable to do DAD, either permanently or until something happens on the
> > underlying device.
> >
> > echo 1 > /sys/class/net/br0/allow_bind_on_tentative_address
> > echo 1 > /sys/class/net/dummy0/allow_bind_on_tentative_address
> > echo 1 > /sys/class/net/wlan0/allow_bind_on_tentative_address
> > and so on...
> >
> > And we may possibly automatically reset this option to 0 if DAD eventually causes the address to be
> > considered duplicate.
>
> The issue is that if DAD rejects a duplicate, the socket is dead and application is
> out of luck.
>
> Has anyone looked at this issue in relation to systemd which does early
> opportunistic binding of services?
I think it is recommended to use the IP_FREEBIND socket option. Which
of course is not available for IPv6.
Ben.
--
Ben Hutchings, Staff Engineer, Solarflare
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
^ permalink raw reply
* Re: [net-next] iproute2: Add new command to IP link to enable/disable VF spoof check
From: David Miller @ 2011-09-26 21:00 UTC (permalink / raw)
To: benve
Cc: shemminger, bhutchings, gregory.v.rose, jeffrey.t.kirsher, netdev,
gospo
In-Reply-To: <184D23435BECB444AB6B9D4630C8EC83028F8A71@XMB-RCD-303.cisco.com>
From: "Christian Benvenuti (benve)" <benve@cisco.com>
Date: Mon, 26 Sep 2011 15:54:53 -0500
> Does it mean that a Netlink interface becomes official (and backward
> compatibility should not be broken) only once iproute2 starts
> supporting it?
It needs to be analyzed on a case-by-case basis. Sometimes we can quickly
fix a poorly designed netlink interface is no major tool takes on use of
the feature.
^ permalink raw reply
* [net-next 1/7] bna: Brocade 1860 IOC PLL, Reg Defs and ASIC Mode Changes
From: Rasesh Mody @ 2011-09-26 21:12 UTC (permalink / raw)
To: davem, netdev; +Cc: adapter_linux_open_src_team, Rasesh Mody, Gurunatha Karaje
In-Reply-To: <1317071541-9662-1-git-send-email-rmody@brocade.com>
Add logic to set ASIC specfic interface in IOC, HW interface initialization
APIs, mode based initialization and MSI-X resource allocation for 1860 with
no asic block. Add new h/w specific register definitions and setup registers
used by IOC logic.
Use normal kernel declaration style, c99 initializers and const for mailbox
structures. Remove unneeded parentheses.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
---
drivers/net/ethernet/brocade/bna/bfa_ioc.c | 8 +-
drivers/net/ethernet/brocade/bna/bfa_ioc.h | 2 +
drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c | 400 ++++++++++++++++++++++++-
3 files changed, 394 insertions(+), 16 deletions(-)
diff --git a/drivers/net/ethernet/brocade/bna/bfa_ioc.c b/drivers/net/ethernet/brocade/bna/bfa_ioc.c
index 4282fef..1e60aa7 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_ioc.c
+++ b/drivers/net/ethernet/brocade/bna/bfa_ioc.c
@@ -1981,7 +1981,13 @@ bfa_nw_ioc_pci_init(struct bfa_ioc *ioc, struct bfa_pcidev *pcidev,
BUG_ON(1);
}
- bfa_nw_ioc_set_ct_hwif(ioc);
+ /**
+ * Set asic specific interfaces.
+ */
+ if (ioc->asic_gen == BFI_ASIC_GEN_CT)
+ bfa_nw_ioc_set_ct_hwif(ioc);
+ else
+ bfa_nw_ioc_set_ct2_hwif(ioc);
bfa_ioc_map_port(ioc);
bfa_ioc_reg_init(ioc);
diff --git a/drivers/net/ethernet/brocade/bna/bfa_ioc.h b/drivers/net/ethernet/brocade/bna/bfa_ioc.h
index e11496d..5899a56 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_ioc.h
+++ b/drivers/net/ethernet/brocade/bna/bfa_ioc.h
@@ -72,6 +72,7 @@ struct bfa_ioc_regs {
void __iomem *hfn_mbox;
void __iomem *lpu_mbox_cmd;
void __iomem *lpu_mbox;
+ void __iomem *lpu_read_stat;
void __iomem *pss_ctl_reg;
void __iomem *pss_err_status_reg;
void __iomem *app_pll_fast_ctl_reg;
@@ -287,6 +288,7 @@ void bfa_nw_ioc_mbox_regisr(struct bfa_ioc *ioc, enum bfi_mclass mc,
} while (0)
void bfa_nw_ioc_set_ct_hwif(struct bfa_ioc *ioc);
+void bfa_nw_ioc_set_ct2_hwif(struct bfa_ioc *ioc);
void bfa_nw_ioc_attach(struct bfa_ioc *ioc, void *bfa,
struct bfa_ioc_cbfn *cbfn);
diff --git a/drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c b/drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c
index 7d0d8ff..b5c189f 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c
+++ b/drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c
@@ -37,7 +37,9 @@
static bool bfa_ioc_ct_firmware_lock(struct bfa_ioc *ioc);
static void bfa_ioc_ct_firmware_unlock(struct bfa_ioc *ioc);
static void bfa_ioc_ct_reg_init(struct bfa_ioc *ioc);
+static void bfa_ioc_ct2_reg_init(struct bfa_ioc *ioc);
static void bfa_ioc_ct_map_port(struct bfa_ioc *ioc);
+static void bfa_ioc_ct2_map_port(struct bfa_ioc *ioc);
static void bfa_ioc_ct_isr_mode_set(struct bfa_ioc *ioc, bool msix);
static void bfa_ioc_ct_notify_fail(struct bfa_ioc *ioc);
static void bfa_ioc_ct_ownership_reset(struct bfa_ioc *ioc);
@@ -48,6 +50,9 @@ static void bfa_ioc_ct_sync_ack(struct bfa_ioc *ioc);
static bool bfa_ioc_ct_sync_complete(struct bfa_ioc *ioc);
static enum bfa_status bfa_ioc_ct_pll_init(void __iomem *rb,
enum bfi_asic_mode asic_mode);
+static enum bfa_status bfa_ioc_ct2_pll_init(void __iomem *rb,
+ enum bfi_asic_mode asic_mode);
+static bool bfa_ioc_ct2_lpu_read_stat(struct bfa_ioc *ioc);
static const struct bfa_ioc_hwif nw_hwif_ct = {
.ioc_pll_init = bfa_ioc_ct_pll_init,
@@ -65,6 +70,23 @@ static const struct bfa_ioc_hwif nw_hwif_ct = {
.ioc_sync_complete = bfa_ioc_ct_sync_complete,
};
+static const struct bfa_ioc_hwif nw_hwif_ct2 = {
+ .ioc_pll_init = bfa_ioc_ct2_pll_init,
+ .ioc_firmware_lock = bfa_ioc_ct_firmware_lock,
+ .ioc_firmware_unlock = bfa_ioc_ct_firmware_unlock,
+ .ioc_reg_init = bfa_ioc_ct2_reg_init,
+ .ioc_map_port = bfa_ioc_ct2_map_port,
+ .ioc_lpu_read_stat = bfa_ioc_ct2_lpu_read_stat,
+ .ioc_isr_mode_set = NULL,
+ .ioc_notify_fail = bfa_ioc_ct_notify_fail,
+ .ioc_ownership_reset = bfa_ioc_ct_ownership_reset,
+ .ioc_sync_start = bfa_ioc_ct_sync_start,
+ .ioc_sync_join = bfa_ioc_ct_sync_join,
+ .ioc_sync_leave = bfa_ioc_ct_sync_leave,
+ .ioc_sync_ack = bfa_ioc_ct_sync_ack,
+ .ioc_sync_complete = bfa_ioc_ct_sync_complete,
+};
+
/**
* Called from bfa_ioc_attach() to map asic specific calls.
*/
@@ -74,6 +96,12 @@ bfa_nw_ioc_set_ct_hwif(struct bfa_ioc *ioc)
ioc->ioc_hwif = &nw_hwif_ct;
}
+void
+bfa_nw_ioc_set_ct2_hwif(struct bfa_ioc *ioc)
+{
+ ioc->ioc_hwif = &nw_hwif_ct2;
+}
+
/**
* Return true if firmware of current driver matches the running firmware.
*/
@@ -170,7 +198,11 @@ bfa_ioc_ct_notify_fail(struct bfa_ioc *ioc)
/**
* Host to LPU mailbox message addresses
*/
-static struct { u32 hfn_mbox, lpu_mbox, hfn_pgn; } ct_fnreg[] = {
+static const struct {
+ u32 hfn_mbox;
+ u32 lpu_mbox;
+ u32 hfn_pgn;
+} ct_fnreg[] = {
{ HOSTFN0_LPU_MBOX0_0, LPU_HOSTFN0_MBOX0_0, HOST_PAGE_NUM_FN0 },
{ HOSTFN1_LPU_MBOX0_8, LPU_HOSTFN1_MBOX0_8, HOST_PAGE_NUM_FN1 },
{ HOSTFN2_LPU_MBOX0_0, LPU_HOSTFN2_MBOX0_0, HOST_PAGE_NUM_FN2 },
@@ -180,7 +212,10 @@ static struct { u32 hfn_mbox, lpu_mbox, hfn_pgn; } ct_fnreg[] = {
/**
* Host <-> LPU mailbox command/status registers - port 0
*/
-static struct { u32 hfn, lpu; } ct_p0reg[] = {
+static const struct {
+ u32 hfn;
+ u32 lpu;
+} ct_p0reg[] = {
{ HOSTFN0_LPU0_CMD_STAT, LPU0_HOSTFN0_CMD_STAT },
{ HOSTFN1_LPU0_CMD_STAT, LPU0_HOSTFN1_CMD_STAT },
{ HOSTFN2_LPU0_CMD_STAT, LPU0_HOSTFN2_CMD_STAT },
@@ -190,13 +225,32 @@ static struct { u32 hfn, lpu; } ct_p0reg[] = {
/**
* Host <-> LPU mailbox command/status registers - port 1
*/
-static struct { u32 hfn, lpu; } ct_p1reg[] = {
+static const struct {
+ u32 hfn;
+ u32 lpu;
+} ct_p1reg[] = {
{ HOSTFN0_LPU1_CMD_STAT, LPU1_HOSTFN0_CMD_STAT },
{ HOSTFN1_LPU1_CMD_STAT, LPU1_HOSTFN1_CMD_STAT },
{ HOSTFN2_LPU1_CMD_STAT, LPU1_HOSTFN2_CMD_STAT },
{ HOSTFN3_LPU1_CMD_STAT, LPU1_HOSTFN3_CMD_STAT }
};
+static const struct {
+ u32 hfn_mbox;
+ u32 lpu_mbox;
+ u32 hfn_pgn;
+ u32 hfn;
+ u32 lpu;
+ u32 lpu_read;
+} ct2_reg[] = {
+ { CT2_HOSTFN_LPU0_MBOX0, CT2_LPU0_HOSTFN_MBOX0, CT2_HOSTFN_PAGE_NUM,
+ CT2_HOSTFN_LPU0_CMD_STAT, CT2_LPU0_HOSTFN_CMD_STAT,
+ CT2_HOSTFN_LPU0_READ_STAT},
+ { CT2_HOSTFN_LPU1_MBOX0, CT2_LPU1_HOSTFN_MBOX0, CT2_HOSTFN_PAGE_NUM,
+ CT2_HOSTFN_LPU1_CMD_STAT, CT2_LPU1_HOSTFN_CMD_STAT,
+ CT2_HOSTFN_LPU1_READ_STAT},
+};
+
static void
bfa_ioc_ct_reg_init(struct bfa_ioc *ioc)
{
@@ -218,8 +272,8 @@ bfa_ioc_ct_reg_init(struct bfa_ioc *ioc)
ioc->ioc_regs.ll_halt = rb + FW_INIT_HALT_P0;
ioc->ioc_regs.alt_ll_halt = rb + FW_INIT_HALT_P1;
} else {
- ioc->ioc_regs.heartbeat = (rb + BFA_IOC1_HBEAT_REG);
- ioc->ioc_regs.ioc_fwstate = (rb + BFA_IOC1_STATE_REG);
+ ioc->ioc_regs.heartbeat = rb + BFA_IOC1_HBEAT_REG;
+ ioc->ioc_regs.ioc_fwstate = rb + BFA_IOC1_STATE_REG;
ioc->ioc_regs.alt_ioc_fwstate = rb + BFA_IOC0_STATE_REG;
ioc->ioc_regs.hfn_mbox_cmd = rb + ct_p1reg[pcifn].hfn;
ioc->ioc_regs.lpu_mbox_cmd = rb + ct_p1reg[pcifn].lpu;
@@ -230,24 +284,24 @@ bfa_ioc_ct_reg_init(struct bfa_ioc *ioc)
/*
* PSS control registers
*/
- ioc->ioc_regs.pss_ctl_reg = (rb + PSS_CTL_REG);
- ioc->ioc_regs.pss_err_status_reg = (rb + PSS_ERR_STATUS_REG);
- ioc->ioc_regs.app_pll_fast_ctl_reg = (rb + APP_PLL_LCLK_CTL_REG);
- ioc->ioc_regs.app_pll_slow_ctl_reg = (rb + APP_PLL_SCLK_CTL_REG);
+ ioc->ioc_regs.pss_ctl_reg = rb + PSS_CTL_REG;
+ ioc->ioc_regs.pss_err_status_reg = rb + PSS_ERR_STATUS_REG;
+ ioc->ioc_regs.app_pll_fast_ctl_reg = rb + APP_PLL_LCLK_CTL_REG;
+ ioc->ioc_regs.app_pll_slow_ctl_reg = rb + APP_PLL_SCLK_CTL_REG;
/*
* IOC semaphore registers and serialization
*/
- ioc->ioc_regs.ioc_sem_reg = (rb + HOST_SEM0_REG);
- ioc->ioc_regs.ioc_usage_sem_reg = (rb + HOST_SEM1_REG);
- ioc->ioc_regs.ioc_init_sem_reg = (rb + HOST_SEM2_REG);
- ioc->ioc_regs.ioc_usage_reg = (rb + BFA_FW_USE_COUNT);
- ioc->ioc_regs.ioc_fail_sync = (rb + BFA_IOC_FAIL_SYNC);
+ ioc->ioc_regs.ioc_sem_reg = rb + HOST_SEM0_REG;
+ ioc->ioc_regs.ioc_usage_sem_reg = rb + HOST_SEM1_REG;
+ ioc->ioc_regs.ioc_init_sem_reg = rb + HOST_SEM2_REG;
+ ioc->ioc_regs.ioc_usage_reg = rb + BFA_FW_USE_COUNT;
+ ioc->ioc_regs.ioc_fail_sync = rb + BFA_IOC_FAIL_SYNC;
/**
* sram memory access
*/
- ioc->ioc_regs.smem_page_start = (rb + PSS_SMEM_PAGE_START);
+ ioc->ioc_regs.smem_page_start = rb + PSS_SMEM_PAGE_START;
ioc->ioc_regs.smem_pg0 = BFI_IOC_SMEM_PG0_CT;
/*
@@ -256,6 +310,64 @@ bfa_ioc_ct_reg_init(struct bfa_ioc *ioc)
ioc->ioc_regs.err_set = (rb + ERR_SET_REG);
}
+static void
+bfa_ioc_ct2_reg_init(struct bfa_ioc *ioc)
+{
+ void __iomem *rb;
+ int port = bfa_ioc_portid(ioc);
+
+ rb = bfa_ioc_bar0(ioc);
+
+ ioc->ioc_regs.hfn_mbox = rb + ct2_reg[port].hfn_mbox;
+ ioc->ioc_regs.lpu_mbox = rb + ct2_reg[port].lpu_mbox;
+ ioc->ioc_regs.host_page_num_fn = rb + ct2_reg[port].hfn_pgn;
+ ioc->ioc_regs.hfn_mbox_cmd = rb + ct2_reg[port].hfn;
+ ioc->ioc_regs.lpu_mbox_cmd = rb + ct2_reg[port].lpu;
+ ioc->ioc_regs.lpu_read_stat = rb + ct2_reg[port].lpu_read;
+
+ if (port == 0) {
+ ioc->ioc_regs.heartbeat = rb + CT2_BFA_IOC0_HBEAT_REG;
+ ioc->ioc_regs.ioc_fwstate = rb + CT2_BFA_IOC0_STATE_REG;
+ ioc->ioc_regs.alt_ioc_fwstate = rb + CT2_BFA_IOC1_STATE_REG;
+ ioc->ioc_regs.ll_halt = rb + FW_INIT_HALT_P0;
+ ioc->ioc_regs.alt_ll_halt = rb + FW_INIT_HALT_P1;
+ } else {
+ ioc->ioc_regs.heartbeat = rb + CT2_BFA_IOC1_HBEAT_REG;
+ ioc->ioc_regs.ioc_fwstate = rb + CT2_BFA_IOC1_STATE_REG;
+ ioc->ioc_regs.alt_ioc_fwstate = rb + CT2_BFA_IOC0_STATE_REG;
+ ioc->ioc_regs.ll_halt = rb + FW_INIT_HALT_P1;
+ ioc->ioc_regs.alt_ll_halt = rb + FW_INIT_HALT_P0;
+ }
+
+ /*
+ * PSS control registers
+ */
+ ioc->ioc_regs.pss_ctl_reg = rb + PSS_CTL_REG;
+ ioc->ioc_regs.pss_err_status_reg = rb + PSS_ERR_STATUS_REG;
+ ioc->ioc_regs.app_pll_fast_ctl_reg = rb + CT2_APP_PLL_LCLK_CTL_REG;
+ ioc->ioc_regs.app_pll_slow_ctl_reg = rb + CT2_APP_PLL_SCLK_CTL_REG;
+
+ /*
+ * IOC semaphore registers and serialization
+ */
+ ioc->ioc_regs.ioc_sem_reg = rb + CT2_HOST_SEM0_REG;
+ ioc->ioc_regs.ioc_usage_sem_reg = rb + CT2_HOST_SEM1_REG;
+ ioc->ioc_regs.ioc_init_sem_reg = rb + CT2_HOST_SEM2_REG;
+ ioc->ioc_regs.ioc_usage_reg = rb + CT2_BFA_FW_USE_COUNT;
+ ioc->ioc_regs.ioc_fail_sync = rb + CT2_BFA_IOC_FAIL_SYNC;
+
+ /**
+ * sram memory access
+ */
+ ioc->ioc_regs.smem_page_start = rb + PSS_SMEM_PAGE_START;
+ ioc->ioc_regs.smem_pg0 = BFI_IOC_SMEM_PG0_CT;
+
+ /*
+ * err set reg : for notification of hb failure in fcmode
+ */
+ ioc->ioc_regs.err_set = rb + ERR_SET_REG;
+}
+
/**
* Initialize IOC to port mapping.
*/
@@ -276,6 +388,16 @@ bfa_ioc_ct_map_port(struct bfa_ioc *ioc)
}
+static void
+bfa_ioc_ct2_map_port(struct bfa_ioc *ioc)
+{
+ void __iomem *rb = ioc->pcidev.pci_bar_kva;
+ u32 r32;
+
+ r32 = readl(rb + CT2_HOSTFN_PERSONALITY0);
+ ioc->port_id = ((r32 & __FC_LL_PORT_MAP__MK) >> __FC_LL_PORT_MAP__SH);
+}
+
/**
* Set interrupt mode for a function: INTX or MSIX
*/
@@ -307,6 +429,50 @@ bfa_ioc_ct_isr_mode_set(struct bfa_ioc *ioc, bool msix)
writel(r32, rb + FNC_PERS_REG);
}
+static bool
+bfa_ioc_ct2_lpu_read_stat(struct bfa_ioc *ioc)
+{
+ u32 r32;
+
+ r32 = readl(ioc->ioc_regs.lpu_read_stat);
+ if (r32) {
+ writel(1, ioc->ioc_regs.lpu_read_stat);
+ return true;
+ }
+
+ return false;
+}
+
+/**
+ * MSI-X resource allocation for 1860 with no asic block
+ */
+#define HOSTFN_MSIX_DEFAULT 64
+#define HOSTFN_MSIX_VT_INDEX_MBOX_ERR 0x30138
+#define HOSTFN_MSIX_VT_OFST_NUMVT 0x3013c
+#define __MSIX_VT_NUMVT__MK 0x003ff800
+#define __MSIX_VT_NUMVT__SH 11
+#define __MSIX_VT_NUMVT_(_v) ((_v) << __MSIX_VT_NUMVT__SH)
+#define __MSIX_VT_OFST_ 0x000007ff
+void
+bfa_ioc_ct2_poweron(struct bfa_ioc *ioc)
+{
+ void __iomem *rb = ioc->pcidev.pci_bar_kva;
+ u32 r32;
+
+ r32 = readl(rb + HOSTFN_MSIX_VT_OFST_NUMVT);
+ if (r32 & __MSIX_VT_NUMVT__MK) {
+ writel(r32 & __MSIX_VT_OFST_,
+ rb + HOSTFN_MSIX_VT_INDEX_MBOX_ERR);
+ return;
+ }
+
+ writel(__MSIX_VT_NUMVT_(HOSTFN_MSIX_DEFAULT - 1) |
+ HOSTFN_MSIX_DEFAULT * bfa_ioc_pcifn(ioc),
+ rb + HOSTFN_MSIX_VT_OFST_NUMVT);
+ writel(HOSTFN_MSIX_DEFAULT * bfa_ioc_pcifn(ioc),
+ rb + HOSTFN_MSIX_VT_INDEX_MBOX_ERR);
+}
+
/**
* Cleanup hw semaphore and usecnt registers
*/
@@ -499,3 +665,207 @@ bfa_ioc_ct_pll_init(void __iomem *rb, enum bfi_asic_mode asic_mode)
writel(0, (rb + MBIST_CTL_REG));
return BFA_STATUS_OK;
}
+
+static void
+bfa_ioc_ct2_sclk_init(void __iomem *rb)
+{
+ u32 r32;
+
+ /*
+ * put s_clk PLL and PLL FSM in reset
+ */
+ r32 = readl((rb + CT2_APP_PLL_SCLK_CTL_REG));
+ r32 &= ~(__APP_PLL_SCLK_ENABLE | __APP_PLL_SCLK_LRESETN);
+ r32 |= (__APP_PLL_SCLK_ENARST | __APP_PLL_SCLK_BYPASS |
+ __APP_PLL_SCLK_LOGIC_SOFT_RESET);
+ writel(r32, (rb + CT2_APP_PLL_SCLK_CTL_REG));
+
+ /*
+ * Ignore mode and program for the max clock (which is FC16)
+ * Firmware/NFC will do the PLL init appropiately
+ */
+ r32 = readl((rb + CT2_APP_PLL_SCLK_CTL_REG));
+ r32 &= ~(__APP_PLL_SCLK_REFCLK_SEL | __APP_PLL_SCLK_CLK_DIV2);
+ writel(r32, (rb + CT2_APP_PLL_SCLK_CTL_REG));
+
+ /*
+ * while doing PLL init dont clock gate ethernet subsystem
+ */
+ r32 = readl((rb + CT2_CHIP_MISC_PRG));
+ writel((r32 | __ETH_CLK_ENABLE_PORT0),
+ (rb + CT2_CHIP_MISC_PRG));
+
+ r32 = readl((rb + CT2_PCIE_MISC_REG));
+ writel((r32 | __ETH_CLK_ENABLE_PORT1),
+ (rb + CT2_PCIE_MISC_REG));
+
+ /*
+ * set sclk value
+ */
+ r32 = readl((rb + CT2_APP_PLL_SCLK_CTL_REG));
+ r32 &= (__P_SCLK_PLL_LOCK | __APP_PLL_SCLK_REFCLK_SEL |
+ __APP_PLL_SCLK_CLK_DIV2);
+ writel(r32 | 0x1061731b, (rb + CT2_APP_PLL_SCLK_CTL_REG));
+
+ /*
+ * poll for s_clk lock or delay 1ms
+ */
+ udelay(1000);
+
+ /*
+ * Dont do clock gating for ethernet subsystem, firmware/NFC will
+ * do this appropriately
+ */
+}
+
+static void
+bfa_ioc_ct2_lclk_init(void __iomem *rb)
+{
+ u32 r32;
+
+ /*
+ * put l_clk PLL and PLL FSM in reset
+ */
+ r32 = readl((rb + CT2_APP_PLL_LCLK_CTL_REG));
+ r32 &= ~(__APP_PLL_LCLK_ENABLE | __APP_PLL_LCLK_LRESETN);
+ r32 |= (__APP_PLL_LCLK_ENARST | __APP_PLL_LCLK_BYPASS |
+ __APP_PLL_LCLK_LOGIC_SOFT_RESET);
+ writel(r32, (rb + CT2_APP_PLL_LCLK_CTL_REG));
+
+ /*
+ * set LPU speed (set for FC16 which will work for other modes)
+ */
+ r32 = readl((rb + CT2_CHIP_MISC_PRG));
+ writel(r32, (rb + CT2_CHIP_MISC_PRG));
+
+ /*
+ * set LPU half speed (set for FC16 which will work for other modes)
+ */
+ r32 = readl((rb + CT2_APP_PLL_LCLK_CTL_REG));
+ writel(r32, (rb + CT2_APP_PLL_LCLK_CTL_REG));
+
+ /*
+ * set lclk for mode (set for FC16)
+ */
+ r32 = readl((rb + CT2_APP_PLL_LCLK_CTL_REG));
+ r32 &= (__P_LCLK_PLL_LOCK | __APP_LPUCLK_HALFSPEED);
+ r32 |= 0x20c1731b;
+ writel(r32, (rb + CT2_APP_PLL_LCLK_CTL_REG));
+
+ /*
+ * poll for s_clk lock or delay 1ms
+ */
+ udelay(1000);
+}
+
+static void
+bfa_ioc_ct2_mem_init(void __iomem *rb)
+{
+ u32 r32;
+
+ r32 = readl((rb + PSS_CTL_REG));
+ r32 &= ~__PSS_LMEM_RESET;
+ writel(r32, (rb + PSS_CTL_REG));
+ udelay(1000);
+
+ writel(__EDRAM_BISTR_START, (rb + CT2_MBIST_CTL_REG));
+ udelay(1000);
+ writel(0, (rb + CT2_MBIST_CTL_REG));
+}
+
+static void
+bfa_ioc_ct2_mac_reset(void __iomem *rb)
+{
+ volatile u32 r32;
+
+ bfa_ioc_ct2_sclk_init(rb);
+ bfa_ioc_ct2_lclk_init(rb);
+
+ /*
+ * release soft reset on s_clk & l_clk
+ */
+ r32 = readl((rb + CT2_APP_PLL_SCLK_CTL_REG));
+ writel((r32 & ~__APP_PLL_SCLK_LOGIC_SOFT_RESET),
+ (rb + CT2_APP_PLL_SCLK_CTL_REG));
+
+ /*
+ * release soft reset on s_clk & l_clk
+ */
+ r32 = readl((rb + CT2_APP_PLL_LCLK_CTL_REG));
+ writel((r32 & ~__APP_PLL_LCLK_LOGIC_SOFT_RESET),
+ (rb + CT2_APP_PLL_LCLK_CTL_REG));
+
+ /* put port0, port1 MAC & AHB in reset */
+ writel((__CSI_MAC_RESET | __CSI_MAC_AHB_RESET),
+ (rb + CT2_CSI_MAC_CONTROL_REG(0)));
+ writel((__CSI_MAC_RESET | __CSI_MAC_AHB_RESET),
+ (rb + CT2_CSI_MAC_CONTROL_REG(1)));
+}
+
+#define CT2_NFC_MAX_DELAY 1000
+static enum bfa_status
+bfa_ioc_ct2_pll_init(void __iomem *rb, enum bfi_asic_mode asic_mode)
+{
+ volatile u32 wgn, r32;
+ int i;
+
+ /*
+ * Initialize PLL if not already done by NFC
+ */
+ wgn = readl(rb + CT2_WGN_STATUS);
+ if (!(wgn & __GLBL_PF_VF_CFG_RDY)) {
+ writel(__HALT_NFC_CONTROLLER, (rb + CT2_NFC_CSR_SET_REG));
+ for (i = 0; i < CT2_NFC_MAX_DELAY; i++) {
+ r32 = readl(rb + CT2_NFC_CSR_SET_REG);
+ if (r32 & __NFC_CONTROLLER_HALTED)
+ break;
+ udelay(1000);
+ }
+ }
+
+ /*
+ * Mask the interrupts and clear any
+ * pending interrupts left by BIOS/EFI
+ */
+
+ writel(1, (rb + CT2_LPU0_HOSTFN_MBOX0_MSK));
+ writel(1, (rb + CT2_LPU1_HOSTFN_MBOX0_MSK));
+
+ r32 = readl((rb + CT2_LPU0_HOSTFN_CMD_STAT));
+ if (r32 == 1) {
+ writel(1, (rb + CT2_LPU0_HOSTFN_CMD_STAT));
+ readl((rb + CT2_LPU0_HOSTFN_CMD_STAT));
+ }
+ r32 = readl((rb + CT2_LPU1_HOSTFN_CMD_STAT));
+ if (r32 == 1) {
+ writel(1, (rb + CT2_LPU1_HOSTFN_CMD_STAT));
+ readl((rb + CT2_LPU1_HOSTFN_CMD_STAT));
+ }
+
+ bfa_ioc_ct2_mac_reset(rb);
+ bfa_ioc_ct2_sclk_init(rb);
+ bfa_ioc_ct2_lclk_init(rb);
+
+ /*
+ * release soft reset on s_clk & l_clk
+ */
+ r32 = readl((rb + CT2_APP_PLL_SCLK_CTL_REG));
+ writel((r32 & ~__APP_PLL_LCLK_LOGIC_SOFT_RESET),
+ (rb + CT2_APP_PLL_SCLK_CTL_REG));
+
+ /*
+ * Announce flash device presence, if flash was corrupted.
+ */
+ if (wgn == (__WGN_READY | __GLBL_PF_VF_CFG_RDY)) {
+ r32 = readl((rb + PSS_GPIO_OUT_REG));
+ writel((r32 & ~1), (rb + PSS_GPIO_OUT_REG));
+ r32 = readl((rb + PSS_GPIO_OE_REG));
+ writel((r32 | 1), (rb + PSS_GPIO_OE_REG));
+ }
+
+ bfa_ioc_ct2_mem_init(rb);
+
+ writel(BFI_IOC_UNINIT, (rb + CT2_BFA_IOC0_STATE_REG));
+ writel(BFI_IOC_UNINIT, (rb + CT2_BFA_IOC1_STATE_REG));
+ return BFA_STATUS_OK;
+}
--
1.7.1
^ permalink raw reply related
* [net-next 0/7] bna: H/W enablement and update driver version to 3.0.2.2
From: Rasesh Mody @ 2011-09-26 21:12 UTC (permalink / raw)
To: davem, netdev; +Cc: adapter_linux_open_src_team, Rasesh Mody
Hi Dave,
The following series is re-submitted. These patches add support for
Brocade-1860 Fabric Adapter and address the comments received.
It updates the Brocade BNA driver to v3.0.2.2.
The driver has been compiled & tested against net-next-2.6(3.0.0-rc7).
Thanks,
Rasesh
Rasesh Mody (7):
bna: Brocade 1860 IOC PLL, Reg Defs and ASIC Mode Changes
bna: Capability Map and MFG Block Changes for New HW
bna: Implement FW Download for New HW
bna: Brocade 1860 HW Enablement
bna: PLL Init Fix and Add Stats Attributes
bna: Add Callback to Fix RXQ Stop
bna: Driver Version changed to 3.0.2.2
drivers/net/ethernet/brocade/bna/bfa_defs.h | 28 ++-
drivers/net/ethernet/brocade/bna/bfa_defs_cna.h | 8 +-
.../net/ethernet/brocade/bna/bfa_defs_mfg_comm.h | 44 +--
drivers/net/ethernet/brocade/bna/bfa_ioc.c | 49 ++-
drivers/net/ethernet/brocade/bna/bfa_ioc.h | 15 +-
drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c | 407 +++++++++++++++++++-
drivers/net/ethernet/brocade/bna/bfi.h | 20 +-
drivers/net/ethernet/brocade/bna/bna_hw_defs.h | 4 +
drivers/net/ethernet/brocade/bna/bna_tx_rx.c | 11 +
drivers/net/ethernet/brocade/bna/bna_types.h | 2 +
drivers/net/ethernet/brocade/bna/bnad.c | 35 ++-
drivers/net/ethernet/brocade/bna/bnad.h | 3 +-
drivers/net/ethernet/brocade/bna/cna.h | 1 +
drivers/net/ethernet/brocade/bna/cna_fwimg.c | 49 ++-
include/linux/pci_ids.h | 1 +
15 files changed, 577 insertions(+), 100 deletions(-)
^ permalink raw reply
* [net-next 2/7] bna: Capability Map and MFG Block Changes for New HW
From: Rasesh Mody @ 2011-09-26 21:12 UTC (permalink / raw)
To: davem, netdev; +Cc: adapter_linux_open_src_team, Rasesh Mody, Gurunatha Karaje
In-Reply-To: <1317071541-9662-1-git-send-email-rmody@brocade.com>
Add capability map and generic model name scheme for manufacturing block.
Add card types for new HW.
Remove bfa_mfg_is_card_type_valid and ibfa_mfg_adapter_prop_init_flash_ct
macros.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
---
drivers/net/ethernet/brocade/bna/bfa_defs.h | 12 +++++-
.../net/ethernet/brocade/bna/bfa_defs_mfg_comm.h | 44 +++----------------
2 files changed, 18 insertions(+), 38 deletions(-)
diff --git a/drivers/net/ethernet/brocade/bna/bfa_defs.h b/drivers/net/ethernet/brocade/bna/bfa_defs.h
index a81c0cc..66a6207 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_defs.h
+++ b/drivers/net/ethernet/brocade/bna/bfa_defs.h
@@ -241,7 +241,17 @@ struct bfa_mfg_block {
u8 num_mac; /*!< number of mac addresses */
u8 rsv2;
u32 card_type; /*!< card type */
- u8 rsv3[108];
+ char cap_nic; /*!< capability nic */
+ char cap_cna; /*!< capability cna */
+ char cap_hba; /*!< capability hba */
+ char cap_fc16g; /*!< capability fc 16g */
+ char cap_sriov; /*!< capability sriov */
+ char cap_mezz; /*!< capability mezz */
+ u8 rsv3;
+ u8 mfg_nports; /*!< number of ports */
+ char media[8]; /*!< xfi/xaui */
+ char initial_mode[8];/*!< initial mode: hba/cna/nic */
+ u8 rsv4[84];
u8 md5_chksum[BFA_MFG_CHKSUM_SIZE]; /*!< md5 checksum */
};
diff --git a/drivers/net/ethernet/brocade/bna/bfa_defs_mfg_comm.h b/drivers/net/ethernet/brocade/bna/bfa_defs_mfg_comm.h
index 7e5df90..6681fe8 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_defs_mfg_comm.h
+++ b/drivers/net/ethernet/brocade/bna/bfa_defs_mfg_comm.h
@@ -60,6 +60,11 @@ enum {
BFA_MFG_TYPE_ASTRA = 807, /*!< Astra mezz card */
BFA_MFG_TYPE_LIGHTNING_P0 = 902, /*!< Lightning mezz card - old */
BFA_MFG_TYPE_LIGHTNING = 1741, /*!< Lightning mezz card */
+ BFA_MFG_TYPE_PROWLER_F = 1560, /*!< Prowler FC only cards */
+ BFA_MFG_TYPE_PROWLER_N = 1410, /*!< Prowler NIC only cards */
+ BFA_MFG_TYPE_PROWLER_C = 1710, /*!< Prowler CNA only cards */
+ BFA_MFG_TYPE_PROWLER_D = 1860, /*!< Prowler Dual cards */
+ BFA_MFG_TYPE_CHINOOK = 1867, /*!< Chinook cards */
BFA_MFG_TYPE_INVALID = 0, /*!< Invalid card type */
};
@@ -73,43 +78,8 @@ enum {
(type) == BFA_MFG_TYPE_WANCHESE || \
(type) == BFA_MFG_TYPE_ASTRA || \
(type) == BFA_MFG_TYPE_LIGHTNING_P0 || \
- (type) == BFA_MFG_TYPE_LIGHTNING))
-
-/**
- * Check if card type valid
- */
-#define bfa_mfg_is_card_type_valid(type) (( \
- (type) == BFA_MFG_TYPE_FC8P2 || \
- (type) == BFA_MFG_TYPE_FC8P1 || \
- (type) == BFA_MFG_TYPE_FC4P2 || \
- (type) == BFA_MFG_TYPE_FC4P1 || \
- (type) == BFA_MFG_TYPE_CNA10P2 || \
- (type) == BFA_MFG_TYPE_CNA10P1 || \
- bfa_mfg_is_mezz(type)))
-
-#define bfa_mfg_adapter_prop_init_flash_ct(mfgblk, prop) \
-do { \
- switch ((mfgblk)->card_type) { \
- case BFA_MFG_TYPE_JAYHAWK: \
- case BFA_MFG_TYPE_ASTRA: \
- (prop) = BFI_ADAPTER_SETP(NPORTS, 2) | \
- BFI_ADAPTER_SETP(SPEED, 8); \
- break; \
- case BFA_MFG_TYPE_CNA10P2: \
- case BFA_MFG_TYPE_WANCHESE: \
- case BFA_MFG_TYPE_LIGHTNING_P0: \
- case BFA_MFG_TYPE_LIGHTNING: \
- (prop) = BFI_ADAPTER_SETP(NPORTS, 2); \
- (prop) |= BFI_ADAPTER_SETP(SPEED, 10); \
- break; \
- case BFA_MFG_TYPE_CNA10P1: \
- (prop) = BFI_ADAPTER_SETP(NPORTS, 1); \
- (prop) |= BFI_ADAPTER_SETP(SPEED, 10); \
- break; \
- default: \
- (prop) = BFI_ADAPTER_UNSUPP; \
- } \
-} while (0)
+ (type) == BFA_MFG_TYPE_LIGHTNING || \
+ (type) == BFA_MFG_TYPE_CHINOOK))
enum {
CB_GPIO_TTV = (1), /*!< TTV debug capable cards */
--
1.7.1
^ permalink raw reply related
* [net-next 3/7] bna: Implement FW Download for New HW
From: Rasesh Mody @ 2011-09-26 21:12 UTC (permalink / raw)
To: davem, netdev; +Cc: adapter_linux_open_src_team, Rasesh Mody, Gurunatha Karaje
In-Reply-To: <1317071541-9662-1-git-send-email-rmody@brocade.com>
Add new asic generation BFI_ASIC_GEN_CT2. Implement FW download from user space
for new Brocade HW 1860.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
---
drivers/net/ethernet/brocade/bna/bfi.h | 1 +
drivers/net/ethernet/brocade/bna/bnad.c | 1 +
drivers/net/ethernet/brocade/bna/cna.h | 1 +
drivers/net/ethernet/brocade/bna/cna_fwimg.c | 49 ++++++++++++++++++++-----
4 files changed, 42 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/brocade/bna/bfi.h b/drivers/net/ethernet/brocade/bna/bfi.h
index 4e04c14..54bcafe 100644
--- a/drivers/net/ethernet/brocade/bna/bfi.h
+++ b/drivers/net/ethernet/brocade/bna/bfi.h
@@ -159,6 +159,7 @@ enum bfi_mclass {
enum bfi_asic_gen {
BFI_ASIC_GEN_CB = 1,
BFI_ASIC_GEN_CT = 2,
+ BFI_ASIC_GEN_CT2 = 3,
};
enum bfi_asic_mode {
diff --git a/drivers/net/ethernet/brocade/bna/bnad.c b/drivers/net/ethernet/brocade/bna/bnad.c
index db6c097..320f11c 100644
--- a/drivers/net/ethernet/brocade/bna/bnad.c
+++ b/drivers/net/ethernet/brocade/bna/bnad.c
@@ -3477,3 +3477,4 @@ MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Brocade 10G PCIe Ethernet driver");
MODULE_VERSION(BNAD_VERSION);
MODULE_FIRMWARE(CNA_FW_FILE_CT);
+MODULE_FIRMWARE(CNA_FW_FILE_CT2);
diff --git a/drivers/net/ethernet/brocade/bna/cna.h b/drivers/net/ethernet/brocade/bna/cna.h
index cb48742..1b3e90d 100644
--- a/drivers/net/ethernet/brocade/bna/cna.h
+++ b/drivers/net/ethernet/brocade/bna/cna.h
@@ -38,6 +38,7 @@
extern char bfa_version[];
#define CNA_FW_FILE_CT "ctfw.bin"
+#define CNA_FW_FILE_CT2 "ct2fw.bin"
#define FC_SYMNAME_MAX 256 /*!< max name server symbolic name size */
#pragma pack(1)
diff --git a/drivers/net/ethernet/brocade/bna/cna_fwimg.c b/drivers/net/ethernet/brocade/bna/cna_fwimg.c
index e8f4ecd..148ebee 100644
--- a/drivers/net/ethernet/brocade/bna/cna_fwimg.c
+++ b/drivers/net/ethernet/brocade/bna/cna_fwimg.c
@@ -16,11 +16,13 @@
* www.brocade.com
*/
#include <linux/firmware.h>
+#include <linux/pci_ids.h>
+#include "bfi.h"
#include "cna.h"
const struct firmware *bfi_fw;
-static u32 *bfi_image_ct_cna;
-static u32 bfi_image_ct_cna_size;
+static u32 *bfi_image_ct_cna, *bfi_image_ct2_cna;
+static u32 bfi_image_ct_cna_size, bfi_image_ct2_cna_size;
static u32 *
cna_read_firmware(struct pci_dev *pdev, u32 **bfi_image,
@@ -45,20 +47,47 @@ error:
u32 *
cna_get_firmware_buf(struct pci_dev *pdev)
{
- if (bfi_image_ct_cna_size == 0)
- cna_read_firmware(pdev, &bfi_image_ct_cna,
- &bfi_image_ct_cna_size, CNA_FW_FILE_CT);
- return bfi_image_ct_cna;
+ if (pdev->device == PCI_DEVICE_ID_BROCADE_CT2) {
+ if (bfi_image_ct2_cna_size == 0)
+ cna_read_firmware(pdev, &bfi_image_ct2_cna,
+ &bfi_image_ct2_cna_size, CNA_FW_FILE_CT2);
+ return bfi_image_ct2_cna;
+ } else if (bfa_asic_id_ct(pdev->device)) {
+ if (bfi_image_ct_cna_size == 0)
+ cna_read_firmware(pdev, &bfi_image_ct_cna,
+ &bfi_image_ct_cna_size, CNA_FW_FILE_CT);
+ return bfi_image_ct_cna;
+ }
+
+ return NULL;
}
u32 *
-bfa_cb_image_get_chunk(int type, u32 off)
+bfa_cb_image_get_chunk(enum bfi_asic_gen asic_gen, u32 off)
{
- return (u32 *)(bfi_image_ct_cna + off);
+ switch (asic_gen) {
+ case BFI_ASIC_GEN_CT:
+ return (u32 *)(bfi_image_ct_cna + off);
+ break;
+ case BFI_ASIC_GEN_CT2:
+ return (u32 *)(bfi_image_ct2_cna + off);
+ break;
+ default:
+ return NULL;
+ }
}
u32
-bfa_cb_image_get_size(int type)
+bfa_cb_image_get_size(enum bfi_asic_gen asic_gen)
{
- return bfi_image_ct_cna_size;
+ switch (asic_gen) {
+ case BFI_ASIC_GEN_CT:
+ return bfi_image_ct_cna_size;
+ break;
+ case BFI_ASIC_GEN_CT2:
+ return bfi_image_ct2_cna_size;
+ break;
+ default:
+ return 0;
+ }
}
--
1.7.1
^ permalink raw reply related
* [net-next 5/7] bna: PLL Init Fix and Add Stats Attributes
From: Rasesh Mody @ 2011-09-26 21:12 UTC (permalink / raw)
To: davem, netdev; +Cc: adapter_linux_open_src_team, Rasesh Mody, Gurunatha Karaje
In-Reply-To: <1317071541-9662-1-git-send-email-rmody@brocade.com>
Change details:
- Fix to release soft reset in PLL init for HW
- Added stats attributes and new bfi msg class
- Removed some unused code and typo fixes
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
---
drivers/net/ethernet/brocade/bna/bfa_defs_cna.h | 8 +++++++-
drivers/net/ethernet/brocade/bna/bfa_ioc.c | 18 ++++++------------
drivers/net/ethernet/brocade/bna/bfa_ioc.h | 12 ++----------
drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c | 9 ++++++++-
drivers/net/ethernet/brocade/bna/bfi.h | 19 ++++++++++---------
5 files changed, 33 insertions(+), 33 deletions(-)
diff --git a/drivers/net/ethernet/brocade/bna/bfa_defs_cna.h b/drivers/net/ethernet/brocade/bna/bfa_defs_cna.h
index 7e0a918..8ab33ee 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_defs_cna.h
+++ b/drivers/net/ethernet/brocade/bna/bfa_defs_cna.h
@@ -15,7 +15,6 @@
* All rights reserved
* www.brocade.com
*/
-
#ifndef __BFA_DEFS_CNA_H__
#define __BFA_DEFS_CNA_H__
@@ -55,6 +54,9 @@ struct bfa_port_fc_stats {
u64 bad_os_count; /*!< Invalid ordered sets */
u64 err_enc_out; /*!< Encoding err nonframe_8b10b */
u64 err_enc; /*!< Encoding err frame_8b10b */
+ u64 bbsc_frames_lost; /*!< Credit Recovery-Frames Lost */
+ u64 bbsc_credits_lost; /*!< Credit Recovery-Credits Lost */
+ u64 bbsc_link_resets; /*!< Credit Recovery-Link Resets */
};
/**
@@ -100,6 +102,10 @@ struct bfa_port_eth_stats {
u64 rx_fcoe_zero_pause; /*!< Rx FCoE zero pause */
u64 tx_fcoe_pause; /*!< Tx FCoE pause */
u64 tx_fcoe_zero_pause; /*!< Tx FCoE zero pause */
+ u64 rx_iscsi_pause; /*!< Rx iSCSI pause */
+ u64 rx_iscsi_zero_pause; /*!< Rx iSCSI zero pause */
+ u64 tx_iscsi_pause; /*!< Tx iSCSI pause */
+ u64 tx_iscsi_zero_pause; /*!< Tx iSCSI zero pause */
};
/**
diff --git a/drivers/net/ethernet/brocade/bna/bfa_ioc.c b/drivers/net/ethernet/brocade/bna/bfa_ioc.c
index 2a91cc8..655556c 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_ioc.c
+++ b/drivers/net/ethernet/brocade/bna/bfa_ioc.c
@@ -17,8 +17,6 @@
*/
#include "bfa_ioc.h"
-#include "cna.h"
-#include "bfi.h"
#include "bfi_reg.h"
#include "bfa_defs.h"
@@ -140,10 +138,6 @@ static struct bfa_sm_table ioc_sm_table[] = {
{BFA_SM(bfa_ioc_sm_hwfail), BFA_IOC_HWFAIL},
};
-/**
- * IOCPF state machine definitions/declarations
- */
-
/*
* Forward declareations for iocpf state machine
*/
@@ -427,7 +421,7 @@ bfa_ioc_sm_disabling_entry(struct bfa_ioc *ioc)
}
/**
- * IOC is being desabled
+ * IOC is being disabled
*/
static void
bfa_ioc_sm_disabling(struct bfa_ioc *ioc, enum ioc_event event)
@@ -457,7 +451,7 @@ bfa_ioc_sm_disabling(struct bfa_ioc *ioc, enum ioc_event event)
}
/**
- * IOC desable completion entry.
+ * IOC disable completion entry.
*/
static void
bfa_ioc_sm_disabled_entry(struct bfa_ioc *ioc)
@@ -782,7 +776,7 @@ static void
bfa_iocpf_sm_hwinit_entry(struct bfa_iocpf *iocpf)
{
iocpf->poll_time = 0;
- bfa_ioc_reset(iocpf->ioc, 0);
+ bfa_ioc_reset(iocpf->ioc, false);
}
/**
@@ -1759,6 +1753,9 @@ bfa_ioc_fail_notify(struct bfa_ioc *ioc)
bfa_ioc_event_notify(ioc, BFA_IOC_E_FAILED);
}
+/**
+ * IOCPF to IOC interface
+ */
static void
bfa_ioc_pf_enabled(struct bfa_ioc *ioc)
{
@@ -2292,9 +2289,6 @@ bfa_ioc_get_adapter_model(struct bfa_ioc *ioc, char *model)
ioc_attr = ioc->attr;
- /**
- * model name
- */
snprintf(model, BFA_ADAPTER_MODEL_NAME_LEN, "%s-%u",
BFA_MFG_NAME, ioc_attr->card_type);
}
diff --git a/drivers/net/ethernet/brocade/bna/bfa_ioc.h b/drivers/net/ethernet/brocade/bna/bfa_ioc.h
index c398170..d5a21f4 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_ioc.h
+++ b/drivers/net/ethernet/brocade/bna/bfa_ioc.h
@@ -152,16 +152,7 @@ struct bfa_ioc_notify {
};
/**
- * Heartbeat failure notification queue element.
- */
-struct bfa_ioc_hbfail_notify {
- struct list_head qe;
- bfa_ioc_hbfail_cbfn_t cbfn;
- void *cbarg;
-};
-
-/**
- * Initialize a heartbeat failure notification structure
+ * Initialize a IOC event notification structure
*/
#define bfa_ioc_notify_init(__notify, __cbfn, __cbarg) do { \
(__notify)->cbfn = (__cbfn); \
@@ -290,6 +281,7 @@ void bfa_nw_ioc_mbox_regisr(struct bfa_ioc *ioc, enum bfi_mclass mc,
void bfa_nw_ioc_set_ct_hwif(struct bfa_ioc *ioc);
void bfa_nw_ioc_set_ct2_hwif(struct bfa_ioc *ioc);
+void bfa_ioc_ct2_poweron(struct bfa_ioc *ioc);
void bfa_nw_ioc_attach(struct bfa_ioc *ioc, void *bfa,
struct bfa_ioc_cbfn *cbfn);
diff --git a/drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c b/drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c
index b5c189f..8c4d42d 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c
+++ b/drivers/net/ethernet/brocade/bna/bfa_ioc_ct.c
@@ -850,10 +850,17 @@ bfa_ioc_ct2_pll_init(void __iomem *rb, enum bfi_asic_mode asic_mode)
* release soft reset on s_clk & l_clk
*/
r32 = readl((rb + CT2_APP_PLL_SCLK_CTL_REG));
- writel((r32 & ~__APP_PLL_LCLK_LOGIC_SOFT_RESET),
+ writel((r32 & ~__APP_PLL_SCLK_LOGIC_SOFT_RESET),
(rb + CT2_APP_PLL_SCLK_CTL_REG));
/*
+ * release soft reset on s_clk & l_clk
+ */
+ r32 = readl((rb + CT2_APP_PLL_LCLK_CTL_REG));
+ writel(r32 & ~__APP_PLL_LCLK_LOGIC_SOFT_RESET,
+ (rb + CT2_APP_PLL_LCLK_CTL_REG));
+
+ /*
* Announce flash device presence, if flash was corrupted.
*/
if (wgn == (__WGN_READY | __GLBL_PF_VF_CFG_RDY)) {
diff --git a/drivers/net/ethernet/brocade/bna/bfi.h b/drivers/net/ethernet/brocade/bna/bfi.h
index 54bcafe..7a1393a 100644
--- a/drivers/net/ethernet/brocade/bna/bfi.h
+++ b/drivers/net/ethernet/brocade/bna/bfi.h
@@ -135,18 +135,22 @@ enum bfi_mclass {
BFI_MC_SFP = 22, /*!< SFP module */
BFI_MC_MSGQ = 23, /*!< MSGQ */
BFI_MC_ENET = 24, /*!< ENET commands/responses */
- BFI_MC_MAX = 32
+ BFI_MC_PHY = 25, /*!< External PHY message class */
+ BFI_MC_NBOOT = 26, /*!< Network Boot */
+ BFI_MC_TIO_READ = 27, /*!< read IO (Target mode) */
+ BFI_MC_TIO_WRITE = 28, /*!< write IO (Target mode) */
+ BFI_MC_TIO_DATA_XFERED = 29, /*!< ds transferred (target mode) */
+ BFI_MC_TIO_IO = 30, /*!< IO (Target mode) */
+ BFI_MC_TIO = 31, /*!< IO (target mode) */
+ BFI_MC_MFG = 32, /*!< MFG/ASIC block commands */
+ BFI_MC_EDMA = 33, /*!< EDMA copy commands */
+ BFI_MC_MAX = 34
};
-#define BFI_IOC_MAX_CQS 4
-#define BFI_IOC_MAX_CQS_ASIC 8
#define BFI_IOC_MSGLEN_MAX 32 /* 32 bytes */
#define BFI_FWBOOT_ENV_OS 0
-#define BFI_BOOT_MEMTEST_RES_ADDR 0x900
-#define BFI_BOOT_MEMTEST_RES_SIG 0xA0A1A2A3
-
/**
*----------------------------------------------------------------------
* IOC
@@ -280,9 +284,6 @@ enum bfi_port_mode {
BFI_PORT_MODE_ETH = 2,
};
-/**
- * BFI_IOC_I2H_READY_EVENT message
- */
struct bfi_ioc_hbeat {
struct bfi_mhdr mh; /*!< common msg header */
u32 hb_count; /*!< current heart beat count */
--
1.7.1
^ permalink raw reply related
* [net-next 4/7] bna: Brocade 1860 HW Enablement
From: Rasesh Mody @ 2011-09-26 21:12 UTC (permalink / raw)
To: davem, netdev; +Cc: adapter_linux_open_src_team, Rasesh Mody, Gurunatha Karaje
In-Reply-To: <1317071541-9662-1-git-send-email-rmody@brocade.com>
This patch enables new HW Brocade 1860. Add BFA_CM_NIC capability mask to
bfa_ioc_attr, Sub-System Device ID Info and support for Brocade 1860 device
ID to bfa_ioc.c bnad.c and pci_ids.h.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
---
drivers/net/ethernet/brocade/bna/bfa_defs.h | 16 +++++++++++++++-
drivers/net/ethernet/brocade/bna/bfa_ioc.c | 23 +++++++++++++++++++++++
drivers/net/ethernet/brocade/bna/bfa_ioc.h | 1 +
drivers/net/ethernet/brocade/bna/bna_hw_defs.h | 4 ++++
drivers/net/ethernet/brocade/bna/bnad.c | 9 ++++++++-
include/linux/pci_ids.h | 1 +
6 files changed, 52 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/brocade/bna/bfa_defs.h b/drivers/net/ethernet/brocade/bna/bfa_defs.h
index 66a6207..48fa410 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_defs.h
+++ b/drivers/net/ethernet/brocade/bna/bfa_defs.h
@@ -193,6 +193,7 @@ struct bfa_ioc_attr {
enum {
BFA_CM_HBA = 0x01,
BFA_CM_CNA = 0x02,
+ BFA_CM_NIC = 0x04,
};
/**
@@ -264,7 +265,20 @@ struct bfa_mfg_block {
#define bfa_asic_id_ct(device) \
((device) == PCI_DEVICE_ID_BROCADE_CT || \
(device) == PCI_DEVICE_ID_BROCADE_CT_FC)
-#define bfa_asic_id_ctc(device) (bfa_asic_id_ct(device))
+#define bfa_asic_id_ct2(device) \
+ ((device) == PCI_DEVICE_ID_BROCADE_CT2)
+#define bfa_asic_id_ctc(device) \
+ (bfa_asic_id_ct(device) || bfa_asic_id_ct2(device))
+
+/**
+ * PCI sub-system device and vendor ID information
+ */
+enum {
+ BFA_PCI_FCOE_SSDEVICE_ID = 0x14,
+ BFA_PCI_CT2_SSID_FCoE = 0x22,
+ BFA_PCI_CT2_SSID_ETH = 0x23,
+ BFA_PCI_CT2_SSID_FC = 0x24,
+};
enum bfa_mode {
BFA_MODE_HBA = 1,
diff --git a/drivers/net/ethernet/brocade/bna/bfa_ioc.c b/drivers/net/ethernet/brocade/bna/bfa_ioc.c
index 1e60aa7..2a91cc8 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_ioc.c
+++ b/drivers/net/ethernet/brocade/bna/bfa_ioc.c
@@ -1977,6 +1977,29 @@ bfa_nw_ioc_pci_init(struct bfa_ioc *ioc, struct bfa_pcidev *pcidev,
ioc->ad_cap_bm = BFA_CM_CNA;
break;
+ case PCI_DEVICE_ID_BROCADE_CT2:
+ ioc->asic_gen = BFI_ASIC_GEN_CT2;
+ if (clscode == BFI_PCIFN_CLASS_FC &&
+ pcidev->ssid == BFA_PCI_CT2_SSID_FC) {
+ ioc->asic_mode = BFI_ASIC_MODE_FC16;
+ ioc->fcmode = true;
+ ioc->port_mode = ioc->port_mode_cfg = BFA_MODE_HBA;
+ ioc->ad_cap_bm = BFA_CM_HBA;
+ } else {
+ ioc->port0_mode = ioc->port1_mode = BFI_PORT_MODE_ETH;
+ ioc->asic_mode = BFI_ASIC_MODE_ETH;
+ if (pcidev->ssid == BFA_PCI_CT2_SSID_FCoE) {
+ ioc->port_mode =
+ ioc->port_mode_cfg = BFA_MODE_CNA;
+ ioc->ad_cap_bm = BFA_CM_CNA;
+ } else {
+ ioc->port_mode =
+ ioc->port_mode_cfg = BFA_MODE_NIC;
+ ioc->ad_cap_bm = BFA_CM_NIC;
+ }
+ }
+ break;
+
default:
BUG_ON(1);
}
diff --git a/drivers/net/ethernet/brocade/bna/bfa_ioc.h b/drivers/net/ethernet/brocade/bna/bfa_ioc.h
index 5899a56..c398170 100644
--- a/drivers/net/ethernet/brocade/bna/bfa_ioc.h
+++ b/drivers/net/ethernet/brocade/bna/bfa_ioc.h
@@ -35,6 +35,7 @@ struct bfa_pcidev {
int pci_slot;
u8 pci_func;
u16 device_id;
+ u16 ssid;
void __iomem *pci_bar_kva;
};
diff --git a/drivers/net/ethernet/brocade/bna/bna_hw_defs.h b/drivers/net/ethernet/brocade/bna/bna_hw_defs.h
index dde8a46..3da6dd9 100644
--- a/drivers/net/ethernet/brocade/bna/bna_hw_defs.h
+++ b/drivers/net/ethernet/brocade/bna/bna_hw_defs.h
@@ -133,6 +133,10 @@
ct_reg_addr_init((_bna), (_pcidev)); \
ct_bit_defn_init((_bna), (_pcidev)); \
break; \
+ case PCI_DEVICE_ID_BROCADE_CT2: \
+ ct2_reg_addr_init((_bna), (_pcidev)); \
+ ct2_bit_defn_init((_bna), (_pcidev)); \
+ break; \
} \
}
diff --git a/drivers/net/ethernet/brocade/bna/bnad.c b/drivers/net/ethernet/brocade/bna/bnad.c
index 320f11c..033c26e 100644
--- a/drivers/net/ethernet/brocade/bna/bnad.c
+++ b/drivers/net/ethernet/brocade/bna/bnad.c
@@ -3428,7 +3428,14 @@ static DEFINE_PCI_DEVICE_TABLE(bnad_pci_id_table) = {
PCI_DEVICE_ID_BROCADE_CT),
.class = PCI_CLASS_NETWORK_ETHERNET << 8,
.class_mask = 0xffff00
- }, {0, }
+ },
+ {
+ PCI_DEVICE(PCI_VENDOR_ID_BROCADE,
+ PCI_DEVICE_ID_BROCADE_CT2),
+ .class = PCI_CLASS_NETWORK_ETHERNET << 8,
+ .class_mask = 0xffff00
+ },
+ {0, },
};
MODULE_DEVICE_TABLE(pci, bnad_pci_id_table);
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index ae96bbe..b12b7ae 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2224,6 +2224,7 @@
#define PCI_DEVICE_ID_BROCADE_CT 0x0014
#define PCI_DEVICE_ID_BROCADE_FC_8G1P 0x0017
#define PCI_DEVICE_ID_BROCADE_CT_FC 0x0021
+#define PCI_DEVICE_ID_BROCADE_CT2 0x0022
#define PCI_VENDOR_ID_SIBYTE 0x166d
#define PCI_DEVICE_ID_BCM1250_PCI 0x0001
--
1.7.1
^ permalink raw reply related
* [net-next 6/7] bna: Add Callback to Fix RXQ Stop
From: Rasesh Mody @ 2011-09-26 21:12 UTC (permalink / raw)
To: davem, netdev; +Cc: adapter_linux_open_src_team, Rasesh Mody, Gurunatha Karaje
In-Reply-To: <1317071541-9662-1-git-send-email-rmody@brocade.com>
Change details:
- Add a callback in the BNA, which is called before sending FW command to stop
RxQs. After this callback is called, driver should not post anymore Rx
buffers to the RxQ. This addresses a small window where driver posts Rx
buffers while FW is stopping/has stopped the RxQ.
- Registering callback function, rx_stall_cbfn, during bna_rx_create.
Invoking callback function, rx_stall_cbfn, before sending rx_cfg_clr
command to FW
- Bnad_cb_rx_stall implementation - set a flag in the Rxq to mark buffer
posting disabled state. While posting buffers check for the above flag.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
---
drivers/net/ethernet/brocade/bna/bna_tx_rx.c | 11 +++++++++++
drivers/net/ethernet/brocade/bna/bna_types.h | 2 ++
drivers/net/ethernet/brocade/bna/bnad.c | 25 ++++++++++++++++++++++++-
drivers/net/ethernet/brocade/bna/bnad.h | 1 +
4 files changed, 38 insertions(+), 1 deletions(-)
diff --git a/drivers/net/ethernet/brocade/bna/bna_tx_rx.c b/drivers/net/ethernet/brocade/bna/bna_tx_rx.c
index 066704e..276fcb5 100644
--- a/drivers/net/ethernet/brocade/bna/bna_tx_rx.c
+++ b/drivers/net/ethernet/brocade/bna/bna_tx_rx.c
@@ -1335,6 +1335,12 @@ do { \
} \
} while (0)
+#define call_rx_stall_cbfn(rx) \
+do { \
+ if ((rx)->rx_stall_cbfn) \
+ (rx)->rx_stall_cbfn((rx)->bna->bnad, (rx)); \
+} while (0)
+
#define bfi_enet_datapath_q_init(bfi_q, bna_qpt) \
do { \
struct bna_dma_addr cur_q_addr = \
@@ -1467,6 +1473,7 @@ bna_rx_sm_rxf_stop_wait(struct bna_rx *rx, enum bna_rx_event event)
case RX_E_FAIL:
bfa_fsm_set_state(rx, bna_rx_sm_cleanup_wait);
bna_rxf_fail(&rx->rxf);
+ call_rx_stall_cbfn(rx);
rx->rx_cleanup_cbfn(rx->bna->bnad, rx);
break;
@@ -1476,6 +1483,7 @@ bna_rx_sm_rxf_stop_wait(struct bna_rx *rx, enum bna_rx_event event)
case RX_E_RXF_STOPPED:
bfa_fsm_set_state(rx, bna_rx_sm_stop_wait);
+ call_rx_stall_cbfn(rx);
bna_rx_enet_stop(rx);
break;
@@ -1516,6 +1524,7 @@ bna_rx_sm_started(struct bna_rx *rx, enum bna_rx_event event)
bfa_fsm_set_state(rx, bna_rx_sm_failed);
bna_ethport_cb_rx_stopped(&rx->bna->ethport);
bna_rxf_fail(&rx->rxf);
+ call_rx_stall_cbfn(rx);
rx->rx_cleanup_cbfn(rx->bna->bnad, rx);
break;
@@ -1536,6 +1545,7 @@ static void bna_rx_sm_rxf_start_wait(struct bna_rx *rx,
case RX_E_FAIL:
bfa_fsm_set_state(rx, bna_rx_sm_failed);
bna_rxf_fail(&rx->rxf);
+ call_rx_stall_cbfn(rx);
rx->rx_cleanup_cbfn(rx->bna->bnad, rx);
break;
@@ -2369,6 +2379,7 @@ bna_rx_create(struct bna *bna, struct bnad *bnad,
rx->rcb_destroy_cbfn = rx_cbfn->rcb_destroy_cbfn;
rx->ccb_setup_cbfn = rx_cbfn->ccb_setup_cbfn;
rx->ccb_destroy_cbfn = rx_cbfn->ccb_destroy_cbfn;
+ rx->rx_stall_cbfn = rx_cbfn->rx_stall_cbfn;
/* Following callbacks are mandatory */
rx->rx_cleanup_cbfn = rx_cbfn->rx_cleanup_cbfn;
rx->rx_post_cbfn = rx_cbfn->rx_post_cbfn;
diff --git a/drivers/net/ethernet/brocade/bna/bna_types.h b/drivers/net/ethernet/brocade/bna/bna_types.h
index 242d799..d090fbf 100644
--- a/drivers/net/ethernet/brocade/bna/bna_types.h
+++ b/drivers/net/ethernet/brocade/bna/bna_types.h
@@ -847,6 +847,7 @@ struct bna_rx {
void (*rcb_destroy_cbfn)(struct bnad *, struct bna_rcb *);
void (*ccb_setup_cbfn)(struct bnad *, struct bna_ccb *);
void (*ccb_destroy_cbfn)(struct bnad *, struct bna_ccb *);
+ void (*rx_stall_cbfn)(struct bnad *, struct bna_rx *);
void (*rx_cleanup_cbfn)(struct bnad *, struct bna_rx *);
void (*rx_post_cbfn)(struct bnad *, struct bna_rx *);
@@ -864,6 +865,7 @@ struct bna_rx_event_cbfn {
void (*rcb_destroy_cbfn)(struct bnad *, struct bna_rcb *);
void (*ccb_setup_cbfn)(struct bnad *, struct bna_ccb *);
void (*ccb_destroy_cbfn)(struct bnad *, struct bna_ccb *);
+ void (*rx_stall_cbfn)(struct bnad *, struct bna_rx *);
/* Mandatory */
void (*rx_cleanup_cbfn)(struct bnad *, struct bna_rx *);
void (*rx_post_cbfn)(struct bnad *, struct bna_rx *);
diff --git a/drivers/net/ethernet/brocade/bna/bnad.c b/drivers/net/ethernet/brocade/bna/bnad.c
index 033c26e..90205dd 100644
--- a/drivers/net/ethernet/brocade/bna/bnad.c
+++ b/drivers/net/ethernet/brocade/bna/bnad.c
@@ -396,7 +396,7 @@ finishing:
unmap_q->producer_index = unmap_prod;
rcb->producer_index = unmap_prod;
smp_mb();
- if (likely(test_bit(BNAD_RXQ_STARTED, &rcb->flags)))
+ if (likely(test_bit(BNAD_RXQ_POST_OK, &rcb->flags)))
bna_rxq_prod_indx_doorbell(rcb);
}
}
@@ -956,6 +956,27 @@ bnad_cb_tx_cleanup(struct bnad *bnad, struct bna_tx *tx)
}
static void
+bnad_cb_rx_stall(struct bnad *bnad, struct bna_rx *rx)
+{
+ struct bnad_rx_info *rx_info = (struct bnad_rx_info *)rx->priv;
+ struct bna_ccb *ccb;
+ struct bnad_rx_ctrl *rx_ctrl;
+ int i;
+
+ for (i = 0; i < BNAD_MAX_RXP_PER_RX; i++) {
+ rx_ctrl = &rx_info->rx_ctrl[i];
+ ccb = rx_ctrl->ccb;
+ if (!ccb)
+ continue;
+
+ clear_bit(BNAD_RXQ_POST_OK, &ccb->rcb[0]->flags);
+
+ if (ccb->rcb[1])
+ clear_bit(BNAD_RXQ_POST_OK, &ccb->rcb[1]->flags);
+ }
+}
+
+static void
bnad_cb_rx_cleanup(struct bnad *bnad, struct bna_rx *rx)
{
struct bnad_rx_info *rx_info = (struct bnad_rx_info *)rx->priv;
@@ -1009,6 +1030,7 @@ bnad_cb_rx_post(struct bnad *bnad, struct bna_rx *rx)
bnad_free_all_rxbufs(bnad, rcb);
set_bit(BNAD_RXQ_STARTED, &rcb->flags);
+ set_bit(BNAD_RXQ_POST_OK, &rcb->flags);
unmap_q = rcb->unmap_q;
/* Now allocate & post buffers for this RCB */
@@ -1898,6 +1920,7 @@ bnad_setup_rx(struct bnad *bnad, u32 rx_id)
.rcb_destroy_cbfn = bnad_cb_rcb_destroy,
.ccb_setup_cbfn = bnad_cb_ccb_setup,
.ccb_destroy_cbfn = bnad_cb_ccb_destroy,
+ .rx_stall_cbfn = bnad_cb_rx_stall,
.rx_cleanup_cbfn = bnad_cb_rx_cleanup,
.rx_post_cbfn = bnad_cb_rx_post,
};
diff --git a/drivers/net/ethernet/brocade/bna/bnad.h b/drivers/net/ethernet/brocade/bna/bnad.h
index 1c9328d..50fb36a 100644
--- a/drivers/net/ethernet/brocade/bna/bnad.h
+++ b/drivers/net/ethernet/brocade/bna/bnad.h
@@ -103,6 +103,7 @@ struct bnad_rx_ctrl {
/* Bit positions for rcb->flags */
#define BNAD_RXQ_REFILL 0
#define BNAD_RXQ_STARTED 1
+#define BNAD_RXQ_POST_OK 2
/* Resource limits */
#define BNAD_NUM_TXQ (bnad->num_tx * bnad->num_txq_per_tx)
--
1.7.1
^ permalink raw reply related
* [net-next 7/7] bna: Driver Version changed to 3.0.2.2
From: Rasesh Mody @ 2011-09-26 21:12 UTC (permalink / raw)
To: davem, netdev; +Cc: adapter_linux_open_src_team, Rasesh Mody, Gurunatha Karaje
In-Reply-To: <1317071541-9662-1-git-send-email-rmody@brocade.com>
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
---
drivers/net/ethernet/brocade/bna/bnad.h | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/drivers/net/ethernet/brocade/bna/bnad.h b/drivers/net/ethernet/brocade/bna/bnad.h
index 50fb36a..5487ca4 100644
--- a/drivers/net/ethernet/brocade/bna/bnad.h
+++ b/drivers/net/ethernet/brocade/bna/bnad.h
@@ -71,7 +71,7 @@ struct bnad_rx_ctrl {
#define BNAD_NAME "bna"
#define BNAD_NAME_LEN 64
-#define BNAD_VERSION "3.0.2.1"
+#define BNAD_VERSION "3.0.2.2"
#define BNAD_MAILBOX_MSIX_INDEX 0
#define BNAD_MAILBOX_MSIX_VECTORS 1
--
1.7.1
^ permalink raw reply related
* Re: [net-next] iproute2: Add new command to IP link to enable/disable VF spoof check
From: Stephen Hemminger @ 2011-09-26 21:19 UTC (permalink / raw)
To: David Miller
Cc: benve, bhutchings, gregory.v.rose, jeffrey.t.kirsher, netdev,
gospo
In-Reply-To: <20110926.170049.1943390151354224651.davem@davemloft.net>
On Mon, 26 Sep 2011 17:00:49 -0400 (EDT)
David Miller <davem@davemloft.net> wrote:
> From: "Christian Benvenuti (benve)" <benve@cisco.com>
> Date: Mon, 26 Sep 2011 15:54:53 -0500
>
> > Does it mean that a Netlink interface becomes official (and backward
> > compatibility should not be broken) only once iproute2 starts
> > supporting it?
>
> It needs to be analyzed on a case-by-case basis. Sometimes we can quickly
> fix a poorly designed netlink interface is no major tool takes on use of
> the feature.
If an interface changes before an official release, there is no
problem. I.e. if an interface goes through multiple versions while
in net-next (or a bug fix during 3.X-rc*) that's fine.
^ permalink raw reply
* Re: [net-next] iproute2: Add new command to IP link to enable/disable VF spoof check
From: David Miller @ 2011-09-26 21:27 UTC (permalink / raw)
To: shemminger
Cc: benve, bhutchings, gregory.v.rose, jeffrey.t.kirsher, netdev,
gospo
In-Reply-To: <20110926141959.58d310c0@nehalam.linuxnetplumber.net>
From: Stephen Hemminger <shemminger@vyatta.com>
Date: Mon, 26 Sep 2011 14:19:59 -0700
> If an interface changes before an official release, there is no
> problem. I.e. if an interface goes through multiple versions while
> in net-next (or a bug fix during 3.X-rc*) that's fine.
Right.
^ permalink raw reply
* Re: [PATCH 1/4] IPVS: Add documentation for new sysctl entries
From: Simon Horman @ 2011-09-26 22:07 UTC (permalink / raw)
To: Randy Dunlap
Cc: lvs-devel, netdev, netfilter-devel, netfilter, Wensong Zhang,
Julian Anastasov, Patrick McHardy
In-Reply-To: <4E80B379.2040701@xenotime.net>
On Mon, Sep 26, 2011 at 10:16:41AM -0700, Randy Dunlap wrote:
> On 09/25/2011 06:23 PM, Simon Horman wrote:
> > Add missing documentation for conntrack, snat_reroute and sync_version.
> >
> > Also fix up a typo, IPVS_DEBUG should be IP_VS_DEBUG.
> >
> > Signed-off-by: Simon Horman <horms@verge.net.au>
> >
> > conntrack
> > ---
> > Documentation/networking/ipvs-sysctl.txt | 53 +++++++++++++++++++++++++++++-
> > 1 files changed, 52 insertions(+), 1 deletions(-)
> >
> > diff --git a/Documentation/networking/ipvs-sysctl.txt b/Documentation/networking/ipvs-sysctl.txt
> > index 4ccdbca..5214339 100644
> > --- a/Documentation/networking/ipvs-sysctl.txt
> > +++ b/Documentation/networking/ipvs-sysctl.txt
> > @@ -15,6 +15,23 @@ amemthresh - INTEGER
> > enabled and the variable is automatically set to 2, otherwise
> > the strategy is disabled and the variable is set to 1.
> >
> > +conntrack - BOOLEAN
> > + 0 - disabled (default)
> > + not 0 - enabled
> > +
> > + If set, maintain connection tracking entries for
> > + connections handled by IPVS.
> > +
> > + This should be enabled if connections handled by IPVS are to be
> > + also handled by stateful firewall rules. That is, iptables rules
> > + that make use of connection tracking. It is a performance
> > + optimisation to disable this setting otherwise.
> > +
> > + Connections handled by the IPVS FTP application module
> > + will have connection tracking entries regardless of this setting.
> > +
> > + Only available when IPVS is compiled with the CONFIG_IP_VS_NFCT
>
> seems to be missing something. Maybe
>
> Only available when IPVS is compiled with CONFIG_IP_VS_NFCT enabled.
> or
> Only available when IPVS is compiled with the CONFIG_IP_VS_NFCT
> symbol enabled.
>
> > +
> > cache_bypass - BOOLEAN
> > 0 - disabled (default)
> > not 0 - enabled
> > @@ -39,7 +56,7 @@ debug_level - INTEGER
> > 11 - IPVS packet handling (ip_vs_in/ip_vs_out)
> > 12 or more - packet traversal
> >
> > - Only available when IPVS is compiled with the CONFIG_IPVS_DEBUG
> > + Only available when IPVS is compiled with the CONFIG_IP_VS_DEBUG
>
> with CONFIG_IP_VS_DEBUG enabled.
>
> >
> > Higher debugging levels include the messages for lower debugging
> > levels, so setting debug level 2, includes level 0, 1 and 2
Thanks Randy,
I was just blindly copying the existing language.
I'll make a follow up patch which incorporates your suggestions.
^ permalink raw reply
* Re: Bridge stays down until a port is added
From: Nicolas de Pesloüan @ 2011-09-26 22:12 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: Marc Haber, netdev
In-Reply-To: <20110926130507.1435d76b@nehalam.linuxnetplumber.net>
Le 26/09/2011 22:05, Stephen Hemminger a écrit :
> On Mon, 26 Sep 2011 22:02:21 +0200
> Nicolas de Pesloüan<nicolas.2p.debian@gmail.com> wrote:
[...]
>> Stephen,
>>
>> What do you think about a generic per-interface option that would cause bind() to accept tentative
>> address hold by a particular interface? This of course violate IPv6 principle, but we are talking
>> about interfaces that are unable to do DAD, either permanently or until something happens on the
>> underlying device.
>>
>> echo 1> /sys/class/net/br0/allow_bind_on_tentative_address
>> echo 1> /sys/class/net/dummy0/allow_bind_on_tentative_address
>> echo 1> /sys/class/net/wlan0/allow_bind_on_tentative_address
>> and so on...
>>
>> And we may possibly automatically reset this option to 0 if DAD eventually causes the address to be
>> considered duplicate.
>
> The issue is that if DAD rejects a duplicate, the socket is dead and application is
> out of luck.
Yes, and this is by design. Setting the option would state "I want to allow early bind(), prior to
DAD and I assume the fact that a possible duplicate address will cause the corresponding socket to
be dead and so the using application."
In the particular use case of a bridge to connect to virtual machines, the user can reasonably
assume that he know what it is doing on this private LAN. As such, he would accept the risk to have
applications die if he end up with a duplicate address.
And this might also allow to set an IPv6 address on a dummy interface, which Marc Haber reported as
not being allowed for now, probably because DAD cannot succeed on a dummy interface and as such, a
bind() cannot be allowed, and as such, setting the IPv6 address is currently useless.
Nicolas.
^ permalink raw reply
* [RFC] bridge: handle bridge group address per 802.1 standards
From: Stephen Hemminger @ 2011-09-26 22:36 UTC (permalink / raw)
To: netdev
The Linux bridge code would process all packets addressed to
the multicast address 01:80:C2:00:00:0X as local and
and never forward. This may have been correct in the ancient past, but
reading the relevant standards, the correct behavior is to handle only
the bridge group address as a special case and leave all other link
local multicast packets alone.
Recently there has been some complaints about forwarding (or not) of
802.1X EAPOL frames by the bridge. Thanks to Tony Jeffree of the
802.1 Bridging Working Group for point me in the correct direction.
The 802.1X-2010 standard Table 11-1 details how different
addresses are assigned based on connectivity associations.
Bridge group address: 01-80-C2-00-00-00
PAE group address: 01-80-C2-00-00-03
Link Layer Discovery 01-80-C2-00-00-0E
Warning: this may mean that some people using bridge who expect
link local packets to be isolated, now need to add firewall rules.
But in my opinion, following the standard is the correct thing to
do regardless.
This means when using 802.1x with libvirt, there are several options:
1. Use macvtap not bridge
2. Turn off STP in libvirt
3. Use PAE group address for 802.1x
4. Provide a user level application using AF_LLC to forward
the 802.2 frames
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
--- a/net/bridge/br_input.c 2011-09-16 13:12:58.061369744 -0700
+++ b/net/bridge/br_input.c 2011-09-26 11:57:41.724554692 -0700
@@ -126,18 +126,6 @@ static int br_handle_local_finish(struct
return 0; /* process further */
}
-/* Does address match the link local multicast address.
- * 01:80:c2:00:00:0X
- */
-static inline int is_link_local(const unsigned char *dest)
-{
- __be16 *a = (__be16 *)dest;
- static const __be16 *b = (const __be16 *)br_group_address;
- static const __be16 m = cpu_to_be16(0xfff0);
-
- return ((a[0] ^ b[0]) | (a[1] ^ b[1]) | ((a[2] ^ b[2]) & m)) == 0;
-}
-
/*
* Return NULL if skb is handled
* note: already called with rcu_read_lock
@@ -161,13 +149,10 @@ rx_handler_result_t br_handle_frame(stru
p = br_port_get_rcu(skb->dev);
- if (unlikely(is_link_local(dest))) {
- /* Pause frames shouldn't be passed up by driver anyway */
- if (skb->protocol == htons(ETH_P_PAUSE))
- goto drop;
-
- /* If STP is turned off, then forward */
- if (p->br->stp_enabled == BR_NO_STP && dest[5] == 0)
+ /* Special handling for bridge group address */
+ if (unlikely(compare_ether_addr(dest, br_group_address) == 0)) {
+ /* If STP is turned off, then act like a hub. */
+ if (p->br->stp_enabled == BR_NO_STP)
goto forward;
if (NF_HOOK(NFPROTO_BRIDGE, NF_BR_LOCAL_IN, skb, skb->dev,
^ permalink raw reply
* Re: Bridge stays down until a port is added
From: Stephen Hemminger @ 2011-09-26 22:42 UTC (permalink / raw)
To: Nicolas de Pesloüan; +Cc: Marc Haber, netdev
In-Reply-To: <4E80F8BD.4010401@gmail.com>
> And this might also allow to set an IPv6 address on a dummy interface, which Marc Haber reported as
> not being allowed for now, probably because DAD cannot succeed on a dummy interface and as such, a
> bind() cannot be allowed, and as such, setting the IPv6 address is currently useless.
For dummy, the interface should probably have the IFF_NOARP flag set.
There isn't any point in doing network discovery on a non-connected
interface. That would make DAD a no-op and bind would work.
^ permalink raw reply
* Re: [PATCH v3 1/7] Basic kernel memory functionality for the Memory Controller
From: Glauber Costa @ 2011-09-26 22:44 UTC (permalink / raw)
To: KAMEZAWA Hiroyuki
Cc: linux-kernel, paul, lizf, ebiederm, davem, gthelen, netdev,
linux-mm, kirill
In-Reply-To: <20110926193451.b419f630.kamezawa.hiroyu@jp.fujitsu.com>
>> #endif
>>
>> -
>> +#ifdef CONFIG_CGROUP_MEM_RES_CTLR_KMEM
>> +int do_kmem_account __read_mostly = 1;
>> +#else
>> +#define do_kmem_account 0
>> +#endif
>
>
> Hmm, do we really need this boot option ?
> From my experience to have swap-accounting boot option,
> this scares us ;) I think config is enough.
If no one else wants it, I can remove it. I personally
don't need it, just wanted to follow the convention laid down by swap here.
>
>
>
>> /*
>> * Statistics for memory cgroup.
>> */
>> @@ -270,6 +274,10 @@ struct mem_cgroup {
>> */
>> struct res_counter memsw;
>> /*
>> + * the counter to account for kmem usage.
>> + */
>> + struct res_counter kmem;
>> + /*
>> * Per cgroup active and inactive list, similar to the
>> * per zone LRU lists.
>> */
>> @@ -321,6 +329,11 @@ struct mem_cgroup {
>> */
>> unsigned long move_charge_at_immigrate;
>> /*
>> + * Should kernel memory limits be stabilished independently
>> + * from user memory ?
>> + */
>> + int kmem_independent;
>> + /*
>> * percpu counter.
>> */
>> struct mem_cgroup_stat_cpu *stat;
>> @@ -388,9 +401,14 @@ enum charge_type {
>> };
>>
>> /* for encoding cft->private value on file */
>> -#define _MEM (0)
>> -#define _MEMSWAP (1)
>> -#define _OOM_TYPE (2)
>> +
>> +enum mem_type {
>> + _MEM = 0,
>> + _MEMSWAP,
>> + _OOM_TYPE,
>> + _KMEM,
>> +};
>> +
>
> ok, nice clean up.
>
>
>> #define MEMFILE_PRIVATE(x, val) (((x)<< 16) | (val))
>> #define MEMFILE_TYPE(val) (((val)>> 16)& 0xffff)
>> #define MEMFILE_ATTR(val) ((val)& 0xffff)
>> @@ -3943,10 +3961,15 @@ static inline u64 mem_cgroup_usage(struct mem_cgroup *mem, bool swap)
>> u64 val;
>>
>> if (!mem_cgroup_is_root(mem)) {
>> + val = 0;
>> + if (!mem->kmem_independent)
>> + val = res_counter_read_u64(&mem->kmem, RES_USAGE);
>
>> if (!swap)
>> - return res_counter_read_u64(&mem->res, RES_USAGE);
>> + val += res_counter_read_u64(&mem->res, RES_USAGE);
>> else
>> - return res_counter_read_u64(&mem->memsw, RES_USAGE);
>> + val += res_counter_read_u64(&mem->memsw, RES_USAGE);
>> +
>> + return val;
>> }
>>
>> val = mem_cgroup_recursive_stat(mem, MEM_CGROUP_STAT_CACHE);
>> @@ -3979,6 +4002,10 @@ static u64 mem_cgroup_read(struct cgroup *cont, struct cftype *cft)
>> else
>> val = res_counter_read_u64(&mem->memsw, name);
>> break;
>> + case _KMEM:
>> + val = res_counter_read_u64(&mem->kmem, name);
>> + break;
>> +
>> default:
>> BUG();
>> break;
>> @@ -4756,6 +4783,21 @@ static int mem_cgroup_reset_vmscan_stat(struct cgroup *cgrp,
>> return 0;
>> }
>>
>> +#ifdef CONFIG_CGROUP_MEM_RES_CTLR_KMEM
>> +static u64 kmem_limit_independent_read(struct cgroup *cont, struct cftype *cft)
>> +{
>> + return mem_cgroup_from_cont(cont)->kmem_independent;
>> +}
>> +
>> +static int kmem_limit_independent_write(struct cgroup *cont, struct cftype *cft,
>> + u64 val)
>> +{
>> + cgroup_lock();
>> + mem_cgroup_from_cont(cont)->kmem_independent = !!val;
>> + cgroup_unlock();
>
> Hm. This code allows that parent/child can have different settings.
> Could you add parent-child check as..
>
> "If parent sets use_hierarchy==1, children must have the same kmem_independent value
> with parant's one."
Agree.
> How do you think ? I think a hierarchy must have the same config.
Yes, I think this is reasonable.
>
> BTW...I don't like naming a little ;)
>
> memory->consolidated/shared/?????_kmem_accounting ?
> Or
> memory->kmem_independent_accounting ?
>
> or some better naming ?
I can go with kmem_independent_accounting if you like, it is fine
by me.
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Fight unfair telecom internet charges in Canada: sign http://stopthemeter.ca/
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>
^ permalink raw reply
* Re: [PATCH v3 2/7] socket: initial cgroup code.
From: Glauber Costa @ 2011-09-26 22:47 UTC (permalink / raw)
To: KAMEZAWA Hiroyuki
Cc: Balbir Singh, Greg Thelen, linux-kernel, paul, lizf, ebiederm,
davem, netdev, linux-mm, kirill
In-Reply-To: <20110926195213.12da87b4.kamezawa.hiroyu@jp.fujitsu.com>
On 09/26/2011 07:52 AM, KAMEZAWA Hiroyuki wrote:
> On Sat, 24 Sep 2011 11:45:04 -0300
> Glauber Costa<glommer@parallels.com> wrote:
>
>> On 09/22/2011 12:09 PM, Balbir Singh wrote:
>>> On Thu, Sep 22, 2011 at 11:30 AM, Greg Thelen<gthelen@google.com> wrote:
>>>> On Wed, Sep 21, 2011 at 11:59 AM, Glauber Costa<glommer@parallels.com> wrote:
>>>>> Right now I am working under the assumption that tasks are long lived inside
>>>>> the cgroup. Migration potentially introduces some nasty locking problems in
>>>>> the mem_schedule path.
>>>>>
>>>>> Also, unless I am missing something, the memcg already has the policy of
>>>>> not carrying charges around, probably because of this very same complexity.
>>>>>
>>>>> True that at least it won't EBUSY you... But I think this is at least a way
>>>>> to guarantee that the cgroup under our nose won't disappear in the middle of
>>>>> our allocations.
>>>>
>>>> Here's the memcg user page behavior using the same pattern:
>>>>
>>>> 1. user page P is allocate by task T in memcg M1
>>>> 2. T is moved to memcg M2. The P charge is left behind still charged
>>>> to M1 if memory.move_charge_at_immigrate=0; or the charge is moved to
>>>> M2 if memory.move_charge_at_immigrate=1.
>>>> 3. rmdir M1 will try to reclaim P (if P was left in M1). If unable to
>>>> reclaim, then P is recharged to parent(M1).
>>>>
>>>
>>> We also have some magic in page_referenced() to remove pages
>>> referenced from different containers. What we do is try not to
>>> penalize a cgroup if another cgroup is referencing this page and the
>>> page under consideration is being reclaimed from the cgroup that
>>> touched it.
>>>
>>> Balbir Singh
>> Do you guys see it as a showstopper for this series to be merged, or can
>> we just TODO it ?
>>
>
> In my experience, 'I can't rmdir cgroup.' is always an important/difficult
> problem. The users cannot know where the accouting is leaking other than
> kmem.usage_in_bytes or memory.usage_in_bytes. and can't fix the issue.
>
> please add EXPERIMENTAL to Kconfig until this is fixed.
I am working on something here that may allow it.
But I think it is independent of the rest, and I can repost the series
fixing the problems raised here without it, + EXPERIMENTAL.
Btw, using EXPERIMENTAL here is a very good idea. I think that we should
turn EXPERIMENTAL on even if I fix for that exists, for a least a couple
of months until we see how this thing really evolves.
What do you think?
>> I can push a proposal for it, but it would be done in a separate patch
>> anyway. Also, we may be in better conditions to fix this when the slab
>> part is merged - since it will likely have the same problems...
>>
>
> Yes. considering sockets which can be shared between tasks(cgroups)
> you'll finally need
> - owner task of socket
> - account moving callback
>
> Or disallow task moving once accounted.
I personally think disallowing task movement once accounted is
reasonable. At least for starters.
I think I can add at least that to the next proposal. Famous last words
is, it should not be that hard...
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Fight unfair telecom internet charges in Canada: sign http://stopthemeter.ca/
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>
^ permalink raw reply
* Re: [PATCH v3 4/7] per-cgroup tcp buffers control
From: Glauber Costa @ 2011-09-26 22:48 UTC (permalink / raw)
To: KAMEZAWA Hiroyuki
Cc: linux-kernel, paul, lizf, ebiederm, davem, gthelen, netdev,
linux-mm, kirill
In-Reply-To: <20110926195906.f1f5831c.kamezawa.hiroyu@jp.fujitsu.com>
On 09/26/2011 07:59 AM, KAMEZAWA Hiroyuki wrote:
> On Sun, 18 Sep 2011 21:56:42 -0300
> Glauber Costa<glommer@parallels.com> wrote:
>
>> With all the infrastructure in place, this patch implements
>> per-cgroup control for tcp memory pressure handling.
>>
>> Signed-off-by: Glauber Costa<glommer@parallels.com>
>> CC: David S. Miller<davem@davemloft.net>
>> CC: Hiroyouki Kamezawa<kamezawa.hiroyu@jp.fujitsu.com>
>> CC: Eric W. Biederman<ebiederm@xmission.com>
>
> a comment below.
>
>> +int tcp_init_cgroup(struct proto *prot, struct cgroup *cgrp,
>> + struct cgroup_subsys *ss)
>> +{
>> + struct mem_cgroup *cg = mem_cgroup_from_cont(cgrp);
>> + unsigned long limit;
>> +
>> + cg->tcp_memory_pressure = 0;
>> + atomic_long_set(&cg->tcp_memory_allocated, 0);
>> + percpu_counter_init(&cg->tcp_sockets_allocated, 0);
>> +
>> + limit = nr_free_buffer_pages() / 8;
>> + limit = max(limit, 128UL);
>> +
>> + cg->tcp_prot_mem[0] = sysctl_tcp_mem[0];
>> + cg->tcp_prot_mem[1] = sysctl_tcp_mem[1];
>> + cg->tcp_prot_mem[2] = sysctl_tcp_mem[2];
>> +
>
> Then, the parameter doesn't inherit parent's one ?
>
> I think sockets_populate should pass 'parent' and
>
>
> I think you should have a function
>
> mem_cgroup_should_inherit_parent_settings(parent)
>
> (This is because you made this feature as a part of memcg.
> please provide expected behavior.)
>
All right Kame, will do.
Thanks.
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Fight unfair telecom internet charges in Canada: sign http://stopthemeter.ca/
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>
^ permalink raw reply
* Re: [PATCH v3 6/7] tcp buffer limitation: per-cgroup limit
From: Glauber Costa @ 2011-09-26 22:49 UTC (permalink / raw)
To: KAMEZAWA Hiroyuki
Cc: Greg Thelen, linux-kernel, paul, lizf, ebiederm, davem, netdev,
linux-mm, kirill
In-Reply-To: <20110926200247.c80f7e47.kamezawa.hiroyu@jp.fujitsu.com>
On 09/26/2011 08:02 AM, KAMEZAWA Hiroyuki wrote:
> On Sat, 24 Sep 2011 10:30:42 -0300
> Glauber Costa<glommer@parallels.com> wrote:
>
>> On 09/22/2011 03:01 AM, Greg Thelen wrote:
>>> On Sun, Sep 18, 2011 at 5:56 PM, Glauber Costa<glommer@parallels.com> wrote:
>>>> +static inline bool mem_cgroup_is_root(struct mem_cgroup *mem)
>>>> +{
>>>> + return (mem == root_mem_cgroup);
>>>> +}
>>>> +
>>>
>>> Why are you adding a copy of mem_cgroup_is_root(). I see one already
>>> in v3.0. Was it deleted in a previous patch?
>>
>> Already answered by another good samaritan.
>>
>>>> +static int tcp_write_maxmem(struct cgroup *cgrp, struct cftype *cft, u64 val)
>>>> +{
>>>> + struct mem_cgroup *sg = mem_cgroup_from_cont(cgrp);
>>>> + struct mem_cgroup *parent = parent_mem_cgroup(sg);
>>>> + struct net *net = current->nsproxy->net_ns;
>>>> + int i;
>>>> +
>>>> + if (!cgroup_lock_live_group(cgrp))
>>>> + return -ENODEV;
>>>
>>> Why is cgroup_lock_live_cgroup() needed here? Does it protect updates
>>> to sg->tcp_prot_mem[*]?
>>>
>>>> +static u64 tcp_read_maxmem(struct cgroup *cgrp, struct cftype *cft)
>>>> +{
>>>> + struct mem_cgroup *sg = mem_cgroup_from_cont(cgrp);
>>>> + u64 ret;
>>>> +
>>>> + if (!cgroup_lock_live_group(cgrp))
>>>> + return -ENODEV;
>>>
>>> Why is cgroup_lock_live_cgroup() needed here? Does it protect updates
>>> to sg->tcp_max_memory?
>>
>> No, that is not my understanding. My understanding is this lock is
>> needed to protect against the cgroup just disappearing under our nose.
>>
>
> Hm. reference count of dentry for cgroup isn't enough ?
>
> Thanks,
> -Kame
>
think think think think think think...
Yeah, I guess it is.
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Fight unfair telecom internet charges in Canada: sign http://stopthemeter.ca/
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox