* FAILED: patch "[PATCH] arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT" failed to apply to 6.12-stable tree
@ 2026-11-07 10:17 Sasha Levin
2026-11-10 5:42 ` [PATCH 6.12.y 1/3] arm64: dts: ti: k3-am625-sk: Remove M4 mailbox node redefinition Sasha Levin
0 siblings, 1 reply; 4+ messages in thread
From: Sasha Levin @ 2026-11-07 10:17 UTC (permalink / raw)
To: jm, m-shah, nm; +Cc: stable
The patch below does not apply to the 6.12-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable@vger.kernel.org>.
To reproduce the conflict and resubmit, you may use the following commands:
git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.12.y
git checkout FETCH_HEAD
git cherry-pick -x 8ef8a0e38d1377c6d51c06f95c64d87641b2c717
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<stable@vger.kernel.org>' --in-reply-to '20261107051734-failed-6.12-8ef8a0e38d13@kernel.org' --subject-prefix 'PATCH 6.12.y' 'HEAD^..'
Thanks,
Sasha
------------------ original commit in Linus's tree ------------------
From 8ef8a0e38d1377c6d51c06f95c64d87641b2c717 Mon Sep 17 00:00:00 2001
From: Judith Mendez <jm@ti.com>
Date: Wed, 9 Sep 2026 16:47:38 -0500
Subject: [PATCH] arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as
OUTPUT
MMC clock pins must be configured as OUTPUT-only per TRM [0] with
receiver disabled (RXACTIVE bit = 0). Change MMC CLK pins from
PIN_INPUT to PIN_OUTPUT to match documentation.
[0] https://www.ti.com/lit/pdf/spruiv7 Rev. C: Table 12-246. MMCSDi I/O Signals
Fixes: d19a66ae488a ("arm64: dts: ti: k3-am625-sk: Enable on board peripherals")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260909214743.899477-11-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
---
arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi b/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
index a5922bd746d86..8e07d2c2e62fd 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
@@ -98,7 +98,7 @@ main_mmc0_pins_default: main-mmc0-default-pins {
bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
- AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
+ AM62X_IOPAD(0x218, PIN_OUTPUT, 0) /* (AB1) MMC0_CLK */
AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
AM62X_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */
AM62X_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */
--
2.53.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 6.12.y 1/3] arm64: dts: ti: k3-am625-sk: Remove M4 mailbox node redefinition
2026-11-07 10:17 FAILED: patch "[PATCH] arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT" failed to apply to 6.12-stable tree Sasha Levin
@ 2026-11-10 5:42 ` Sasha Levin
2026-11-10 5:42 ` [PATCH 6.12.y 2/3] arm64: dts: ti: k3-am62*: remove SoC dtsi from common dtsi Sasha Levin
2026-11-10 5:42 ` [PATCH 6.12.y 3/3] arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT Sasha Levin
0 siblings, 2 replies; 4+ messages in thread
From: Sasha Levin @ 2026-11-10 5:42 UTC (permalink / raw)
To: stable; +Cc: Andrew Davis, Nishanth Menon, Sasha Levin
From: Andrew Davis <afd@ti.com>
[ Upstream commit 17d0723c6cf841ebaf510eaf9bb1ebf4991d6e9d ]
This node is already defined in the included k3-am62x-sk-common.dtsi.
Remove this redefinition.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20241203164031.20211-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Stable-dep-of: 8ef8a0e38d13 ("arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 7 -------
1 file changed, 7 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 0fa11d3aa71e9..d240165bda9c5 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -243,13 +243,6 @@ cpsw3g_phy1: ethernet-phy@1 {
};
};
-&mailbox0_cluster0 {
- mbox_m4_0: mbox-m4-0 {
- ti,mbox-rx = <0 0 0>;
- ti,mbox-tx = <1 0 0>;
- };
-};
-
&fss {
bootph-all;
};
--
2.53.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 6.12.y 2/3] arm64: dts: ti: k3-am62*: remove SoC dtsi from common dtsi
2026-11-10 5:42 ` [PATCH 6.12.y 1/3] arm64: dts: ti: k3-am625-sk: Remove M4 mailbox node redefinition Sasha Levin
@ 2026-11-10 5:42 ` Sasha Levin
2026-11-10 5:42 ` [PATCH 6.12.y 3/3] arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT Sasha Levin
1 sibling, 0 replies; 4+ messages in thread
From: Sasha Levin @ 2026-11-10 5:42 UTC (permalink / raw)
To: stable; +Cc: Anshul Dalal, Bryan Brattlof, Nishanth Menon, Sasha Levin
From: Anshul Dalal <anshuld@ti.com>
[ Upstream commit e0b9feca7329c495a76891d7766a781dea73787d ]
The k3-am62x-sk-common dtsi represents the common hardware used across
am62x EVMs which can be configured with various DDR sizes or none (with
DDR integrated in the package) based on the specific am62x SoC used.
Therefore this patch moves the memory node and the SoC specific k3-am625
dtsi out of sk-common and into the board dts files. No functional change
is intended from this patch. The device-tree inheritance is changed as
follows:
Before:
k3-am62
^
k3-am625
^
k3-am62x-sk-common
^
am62x EVMs (k3-am625-sk, k3-am62-lp-sk)
After:
k3-am62
^
k3-am625 k3-am62x-sk-common
^ ^
am62x EVMs (k3-am625-sk, k3-am62-lp-sk)
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://patch.msgid.link/20250814134531.2743874-2-anshuld@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Move the SoC include and RAM description out of the shared evaluation
board description and into the individual board descriptions. Preserve
the existing unlabeled reserved-memory node.
Also extract the existing AM625 SK hardware description into a common
include, keeping the SoC selection, board identity and RAM in the board
description. This supplies the location needed by the subsequent eMMC
clock pin correction without adding support for another board.
Keep all existing hardware properties, including boot phase annotations,
the eMMC non-removable flag and the audio codec supply. No functional
change is intended.
Stable-dep-of: 8ef8a0e38d13 ("arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts | 8 +
.../arm64/boot/dts/ti/k3-am625-sk-common.dtsi | 304 ++++++++++++++++++
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 301 +----------------
.../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 8 -
4 files changed, 316 insertions(+), 305 deletions(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
diff --git a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
index cb5e8364c9731..fc79641d7bb5f 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
@@ -7,12 +7,20 @@
/dts-v1/;
+#include "k3-am625.dtsi"
#include "k3-am62x-sk-common.dtsi"
/ {
compatible = "ti,am62-lp-sk", "ti,am625";
model = "Texas Instruments AM62x LP SK";
+ memory@80000000 {
+ /* 2G RAM */
+ reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+ device_type = "memory";
+ bootph-pre-ram;
+ };
+
vmain_pd: regulator-0 {
/* TPS65988 PD CONTROLLER OUTPUT */
compatible = "regulator-fixed";
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi b/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
new file mode 100644
index 0000000000000..a9e372e9feada
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
@@ -0,0 +1,304 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Common dtsi for AM625 SK and derivatives
+ *
+ * Copyright (C) 2021-2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include "k3-am62x-sk-common.dtsi"
+
+/ {
+ opp-table {
+ /* Add 1.4GHz OPP for am625-sk board. Requires VDD_CORE to be at 0.85V */
+ opp-1400000000 {
+ opp-hz = /bits/ 64 <1400000000>;
+ opp-supported-hw = <0x01 0x0004>;
+ clock-latency-ns = <6000000>;
+ };
+ };
+
+ vmain_pd: regulator-0 {
+ /* TPS65988 PD CONTROLLER OUTPUT */
+ bootph-all;
+ compatible = "regulator-fixed";
+ regulator-name = "vmain_pd";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_5v0: regulator-1 {
+ /* Output of LM34936 */
+ bootph-all;
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vmain_pd>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_3v3_sys: regulator-2 {
+ /* output of LM61460-Q1 */
+ bootph-all;
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_sys";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vmain_pd>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: regulator-3 {
+ /* TPS22918DBVR */
+ bootph-all;
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vcc_3v3_sys>;
+ gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: regulator-4 {
+ /* Output of TLV71033 */
+ bootph-all;
+ compatible = "regulator-gpio";
+ regulator-name = "tlv71033";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vcc_5v0>;
+ gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+
+ vcc_1v8: regulator-5 {
+ /* output of TPS6282518DMQ */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&main_pmx0 {
+ main_mmc0_pins_default: main-mmc0-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
+ AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
+ AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
+ AM62X_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */
+ AM62X_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */
+ AM62X_IOPAD(0x208, PIN_INPUT_PULLUP, 0) /* (Y4) MMC0_DAT3 */
+ AM62X_IOPAD(0x204, PIN_INPUT_PULLUP, 0) /* (AB2) MMC0_DAT4 */
+ AM62X_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */
+ AM62X_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */
+ AM62X_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */
+ >;
+ };
+
+ main_rgmii2_pins_default: main-rgmii2-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
+ AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
+ AM62X_IOPAD(0x18c, PIN_INPUT, 0) /* (AC21) RGMII2_RD2 */
+ AM62X_IOPAD(0x190, PIN_INPUT, 0) /* (AE22) RGMII2_RD3 */
+ AM62X_IOPAD(0x180, PIN_INPUT, 0) /* (AD23) RGMII2_RXC */
+ AM62X_IOPAD(0x17c, PIN_INPUT, 0) /* (AD22) RGMII2_RX_CTL */
+ AM62X_IOPAD(0x16c, PIN_OUTPUT, 0) /* (Y18) RGMII2_TD0 */
+ AM62X_IOPAD(0x170, PIN_OUTPUT, 0) /* (AA18) RGMII2_TD1 */
+ AM62X_IOPAD(0x174, PIN_OUTPUT, 0) /* (AD21) RGMII2_TD2 */
+ AM62X_IOPAD(0x178, PIN_OUTPUT, 0) /* (AC20) RGMII2_TD3 */
+ AM62X_IOPAD(0x168, PIN_OUTPUT, 0) /* (AE21) RGMII2_TXC */
+ AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
+ >;
+ };
+
+ ospi0_pins_default: ospi0-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
+ AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
+ AM62X_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
+ AM62X_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
+ AM62X_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
+ AM62X_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
+ AM62X_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
+ AM62X_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
+ AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
+ AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
+ AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
+ >;
+ };
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
+ >;
+ };
+
+ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
+ >;
+ };
+};
+
+&main_gpio0 {
+ bootph-all;
+};
+
+&main_gpio1 {
+ bootph-all;
+};
+
+&main_i2c1 {
+ bootph-all;
+ exp1: gpio@22 {
+ bootph-all;
+ compatible = "ti,tca6424";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
+ "PRU_DETECT", "MMC1_SD_EN",
+ "VPP_LDO_EN", "EXP_PS_3V3_En",
+ "EXP_PS_5V0_En", "EXP_HAT_DETECT",
+ "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn",
+ "UART1_FET_BUF_EN", "WL_LT_EN",
+ "GPIO_HDMI_RSTn", "CSI_GPIO1",
+ "CSI_GPIO2", "PRU_3V3_EN",
+ "HDMI_INTn", "PD_I2C_IRQ",
+ "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
+ "MCASP1_FET_SEL", "UART1_FET_SEL",
+ "TSINT#", "IO_EXP_TEST_LED";
+
+ interrupt-parent = <&main_gpio1>;
+ interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+ };
+};
+
+&sdhci0 {
+ bootph-all;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc0_pins_default>;
+ status = "okay";
+};
+
+&sdhci1 {
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
+};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_rgmii1_pins_default>, <&main_rgmii2_pins_default>;
+};
+
+&cpsw_port2 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy1>;
+};
+
+&cpsw3g_mdio {
+ cpsw3g_phy1: ethernet-phy@1 {
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
+&fss {
+ bootph-all;
+};
+
+&ospi0 {
+ bootph-all;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ospi0_pins_default>;
+
+ flash@0 {
+ bootph-all;
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+
+ partitions {
+ bootph-all;
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ospi.tiboot3";
+ reg = <0x0 0x80000>;
+ };
+
+ partition@80000 {
+ label = "ospi.tispl";
+ reg = <0x80000 0x200000>;
+ };
+
+ partition@280000 {
+ label = "ospi.u-boot";
+ reg = <0x280000 0x400000>;
+ };
+
+ partition@680000 {
+ label = "ospi.env";
+ reg = <0x680000 0x40000>;
+ };
+
+ partition@6c0000 {
+ label = "ospi.env.backup";
+ reg = <0x6c0000 0x40000>;
+ };
+
+ partition@800000 {
+ label = "ospi.rootfs";
+ reg = <0x800000 0x37c0000>;
+ };
+
+ partition@3fc0000 {
+ bootph-pre-ram;
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ };
+ };
+ };
+};
+
+&tlv320aic3106 {
+ DVDD-supply = <&vcc_1v8>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index d240165bda9c5..52954c77df804 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -7,310 +7,17 @@
/dts-v1/;
-#include "k3-am62x-sk-common.dtsi"
+#include "k3-am625.dtsi"
+#include "k3-am625-sk-common.dtsi"
/ {
compatible = "ti,am625-sk", "ti,am625";
model = "Texas Instruments AM625 SK";
- opp-table {
- /* Add 1.4GHz OPP for am625-sk board. Requires VDD_CORE to be at 0.85V */
- opp-1400000000 {
- opp-hz = /bits/ 64 <1400000000>;
- opp-supported-hw = <0x01 0x0004>;
- clock-latency-ns = <6000000>;
- };
- };
-
memory@80000000 {
- device_type = "memory";
/* 2G RAM */
reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
-
- };
-
- vmain_pd: regulator-0 {
- /* TPS65988 PD CONTROLLER OUTPUT */
- bootph-all;
- compatible = "regulator-fixed";
- regulator-name = "vmain_pd";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- vcc_5v0: regulator-1 {
- /* Output of LM34936 */
- bootph-all;
- compatible = "regulator-fixed";
- regulator-name = "vcc_5v0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&vmain_pd>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- vcc_3v3_sys: regulator-2 {
- /* output of LM61460-Q1 */
- bootph-all;
- compatible = "regulator-fixed";
- regulator-name = "vcc_3v3_sys";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&vmain_pd>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- vdd_mmc1: regulator-3 {
- /* TPS22918DBVR */
- bootph-all;
- compatible = "regulator-fixed";
- regulator-name = "vdd_mmc1";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- enable-active-high;
- vin-supply = <&vcc_3v3_sys>;
- gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
- };
-
- vdd_sd_dv: regulator-4 {
- /* Output of TLV71033 */
- bootph-all;
- compatible = "regulator-gpio";
- regulator-name = "tlv71033";
- pinctrl-names = "default";
- pinctrl-0 = <&vdd_sd_dv_pins_default>;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- vin-supply = <&vcc_5v0>;
- gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
- states = <1800000 0x0>,
- <3300000 0x1>;
- };
-
- vcc_1v8: regulator-5 {
- /* output of TPS6282518DMQ */
- compatible = "regulator-fixed";
- regulator-name = "vcc_1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vcc_3v3_sys>;
- regulator-always-on;
- regulator-boot-on;
- };
-};
-
-&main_pmx0 {
- main_mmc0_pins_default: main-mmc0-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
- AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
- AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
- AM62X_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */
- AM62X_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */
- AM62X_IOPAD(0x208, PIN_INPUT_PULLUP, 0) /* (Y4) MMC0_DAT3 */
- AM62X_IOPAD(0x204, PIN_INPUT_PULLUP, 0) /* (AB2) MMC0_DAT4 */
- AM62X_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */
- AM62X_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */
- AM62X_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */
- >;
- };
-
- main_rgmii2_pins_default: main-rgmii2-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
- AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
- AM62X_IOPAD(0x18c, PIN_INPUT, 0) /* (AC21) RGMII2_RD2 */
- AM62X_IOPAD(0x190, PIN_INPUT, 0) /* (AE22) RGMII2_RD3 */
- AM62X_IOPAD(0x180, PIN_INPUT, 0) /* (AD23) RGMII2_RXC */
- AM62X_IOPAD(0x17c, PIN_INPUT, 0) /* (AD22) RGMII2_RX_CTL */
- AM62X_IOPAD(0x16c, PIN_OUTPUT, 0) /* (Y18) RGMII2_TD0 */
- AM62X_IOPAD(0x170, PIN_OUTPUT, 0) /* (AA18) RGMII2_TD1 */
- AM62X_IOPAD(0x174, PIN_OUTPUT, 0) /* (AD21) RGMII2_TD2 */
- AM62X_IOPAD(0x178, PIN_OUTPUT, 0) /* (AC20) RGMII2_TD3 */
- AM62X_IOPAD(0x168, PIN_OUTPUT, 0) /* (AE21) RGMII2_TXC */
- AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
- >;
- };
-
- ospi0_pins_default: ospi0-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
- AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
- AM62X_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
- AM62X_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
- AM62X_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
- AM62X_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
- AM62X_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
- AM62X_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
- AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
- AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
- AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
- >;
- };
-
- vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
- >;
- };
-
- main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
- >;
- };
-};
-
-&main_gpio0 {
- bootph-all;
-};
-
-&main_gpio1 {
- bootph-all;
-};
-
-&main_i2c1 {
- bootph-all;
- exp1: gpio@22 {
- bootph-all;
- compatible = "ti,tca6424";
- reg = <0x22>;
- gpio-controller;
- #gpio-cells = <2>;
- gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
- "PRU_DETECT", "MMC1_SD_EN",
- "VPP_LDO_EN", "EXP_PS_3V3_En",
- "EXP_PS_5V0_En", "EXP_HAT_DETECT",
- "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn",
- "UART1_FET_BUF_EN", "WL_LT_EN",
- "GPIO_HDMI_RSTn", "CSI_GPIO1",
- "CSI_GPIO2", "PRU_3V3_EN",
- "HDMI_INTn", "PD_I2C_IRQ",
- "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
- "MCASP1_FET_SEL", "UART1_FET_SEL",
- "TSINT#", "IO_EXP_TEST_LED";
-
- interrupt-parent = <&main_gpio1>;
- interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
- };
-};
-
-&sdhci0 {
- bootph-all;
- non-removable;
- pinctrl-names = "default";
- pinctrl-0 = <&main_mmc0_pins_default>;
- status = "okay";
-};
-
-&sdhci1 {
- vmmc-supply = <&vdd_mmc1>;
- vqmmc-supply = <&vdd_sd_dv>;
-};
-
-&cpsw3g {
- pinctrl-names = "default";
- pinctrl-0 = <&main_rgmii1_pins_default>, <&main_rgmii2_pins_default>;
-};
-
-&cpsw_port2 {
- phy-mode = "rgmii-rxid";
- phy-handle = <&cpsw3g_phy1>;
-};
-
-&cpsw3g_mdio {
- cpsw3g_phy1: ethernet-phy@1 {
- reg = <1>;
- ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
- ti,min-output-impedance;
- };
-};
-
-&fss {
- bootph-all;
-};
-
-&ospi0 {
- bootph-all;
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&ospi0_pins_default>;
-
- flash@0 {
- bootph-all;
- compatible = "jedec,spi-nor";
- reg = <0x0>;
- spi-tx-bus-width = <8>;
- spi-rx-bus-width = <8>;
- spi-max-frequency = <25000000>;
- cdns,tshsl-ns = <60>;
- cdns,tsd2d-ns = <60>;
- cdns,tchsh-ns = <60>;
- cdns,tslch-ns = <60>;
- cdns,read-delay = <4>;
-
- partitions {
- bootph-all;
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "ospi.tiboot3";
- reg = <0x0 0x80000>;
- };
-
- partition@80000 {
- label = "ospi.tispl";
- reg = <0x80000 0x200000>;
- };
-
- partition@280000 {
- label = "ospi.u-boot";
- reg = <0x280000 0x400000>;
- };
-
- partition@680000 {
- label = "ospi.env";
- reg = <0x680000 0x40000>;
- };
-
- partition@6c0000 {
- label = "ospi.env.backup";
- reg = <0x6c0000 0x40000>;
- };
-
- partition@800000 {
- label = "ospi.rootfs";
- reg = <0x800000 0x37c0000>;
- };
-
- partition@3fc0000 {
- bootph-pre-ram;
- label = "ospi.phypattern";
- reg = <0x3fc0000 0x40000>;
- };
- };
+ device_type = "memory";
+ bootph-pre-ram;
};
};
-
-&tlv320aic3106 {
- DVDD-supply = <&vcc_1v8>;
-};
diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
index 9d45d8dad381e..be5cc73cf2e4b 100644
--- a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
@@ -8,7 +8,6 @@
#include <dt-bindings/leds/common.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/net/ti-dp83867.h>
-#include "k3-am625.dtsi"
/ {
aliases {
@@ -27,13 +26,6 @@ chosen {
stdout-path = "serial2:115200n8";
};
- memory@80000000 {
- bootph-pre-ram;
- device_type = "memory";
- /* 2G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
- };
-
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
--
2.53.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 6.12.y 3/3] arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT
2026-11-10 5:42 ` [PATCH 6.12.y 1/3] arm64: dts: ti: k3-am625-sk: Remove M4 mailbox node redefinition Sasha Levin
2026-11-10 5:42 ` [PATCH 6.12.y 2/3] arm64: dts: ti: k3-am62*: remove SoC dtsi from common dtsi Sasha Levin
@ 2026-11-10 5:42 ` Sasha Levin
1 sibling, 0 replies; 4+ messages in thread
From: Sasha Levin @ 2026-11-10 5:42 UTC (permalink / raw)
To: stable; +Cc: Judith Mendez, Moteen Shah, Nishanth Menon, Sasha Levin
From: Judith Mendez <jm@ti.com>
[ Upstream commit 8ef8a0e38d1377c6d51c06f95c64d87641b2c717 ]
MMC clock pins must be configured as OUTPUT-only per TRM [0] with
receiver disabled (RXACTIVE bit = 0). Change MMC CLK pins from
PIN_INPUT to PIN_OUTPUT to match documentation.
[0] https://www.ti.com/lit/pdf/spruiv7 Rev. C: Table 12-246. MMCSDi I/O Signals
Fixes: d19a66ae488a ("arm64: dts: ti: k3-am625-sk: Enable on board peripherals")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260909214743.899477-11-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi b/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
index a9e372e9feada..db85d354133f6 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
@@ -98,7 +98,7 @@ main_mmc0_pins_default: main-mmc0-default-pins {
bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
- AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
+ AM62X_IOPAD(0x218, PIN_OUTPUT, 0) /* (AB1) MMC0_CLK */
AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
AM62X_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */
AM62X_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */
--
2.53.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
end of thread, other threads:[~2026-11-10 5:42 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-07 10:17 FAILED: patch "[PATCH] arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT" failed to apply to 6.12-stable tree Sasha Levin
2026-11-10 5:42 ` [PATCH 6.12.y 1/3] arm64: dts: ti: k3-am625-sk: Remove M4 mailbox node redefinition Sasha Levin
2026-11-10 5:42 ` [PATCH 6.12.y 2/3] arm64: dts: ti: k3-am62*: remove SoC dtsi from common dtsi Sasha Levin
2026-11-10 5:42 ` [PATCH 6.12.y 3/3] arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT Sasha Levin
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox