* [PATCH 6.12.y 2/3] arm64: dts: ti: k3-am62*: remove SoC dtsi from common dtsi
2026-11-10 5:42 ` [PATCH 6.12.y 1/3] arm64: dts: ti: k3-am625-sk: Remove M4 mailbox node redefinition Sasha Levin
@ 2026-11-10 5:42 ` Sasha Levin
2026-11-10 5:42 ` [PATCH 6.12.y 3/3] arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT Sasha Levin
1 sibling, 0 replies; 4+ messages in thread
From: Sasha Levin @ 2026-11-10 5:42 UTC (permalink / raw)
To: stable; +Cc: Anshul Dalal, Bryan Brattlof, Nishanth Menon, Sasha Levin
From: Anshul Dalal <anshuld@ti.com>
[ Upstream commit e0b9feca7329c495a76891d7766a781dea73787d ]
The k3-am62x-sk-common dtsi represents the common hardware used across
am62x EVMs which can be configured with various DDR sizes or none (with
DDR integrated in the package) based on the specific am62x SoC used.
Therefore this patch moves the memory node and the SoC specific k3-am625
dtsi out of sk-common and into the board dts files. No functional change
is intended from this patch. The device-tree inheritance is changed as
follows:
Before:
k3-am62
^
k3-am625
^
k3-am62x-sk-common
^
am62x EVMs (k3-am625-sk, k3-am62-lp-sk)
After:
k3-am62
^
k3-am625 k3-am62x-sk-common
^ ^
am62x EVMs (k3-am625-sk, k3-am62-lp-sk)
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://patch.msgid.link/20250814134531.2743874-2-anshuld@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Move the SoC include and RAM description out of the shared evaluation
board description and into the individual board descriptions. Preserve
the existing unlabeled reserved-memory node.
Also extract the existing AM625 SK hardware description into a common
include, keeping the SoC selection, board identity and RAM in the board
description. This supplies the location needed by the subsequent eMMC
clock pin correction without adding support for another board.
Keep all existing hardware properties, including boot phase annotations,
the eMMC non-removable flag and the audio codec supply. No functional
change is intended.
Stable-dep-of: 8ef8a0e38d13 ("arm64: dts: ti: k3-am625-sk-common: Set eMMC clock pin as OUTPUT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts | 8 +
.../arm64/boot/dts/ti/k3-am625-sk-common.dtsi | 304 ++++++++++++++++++
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 301 +----------------
.../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 8 -
4 files changed, 316 insertions(+), 305 deletions(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
diff --git a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
index cb5e8364c9731..fc79641d7bb5f 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
@@ -7,12 +7,20 @@
/dts-v1/;
+#include "k3-am625.dtsi"
#include "k3-am62x-sk-common.dtsi"
/ {
compatible = "ti,am62-lp-sk", "ti,am625";
model = "Texas Instruments AM62x LP SK";
+ memory@80000000 {
+ /* 2G RAM */
+ reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+ device_type = "memory";
+ bootph-pre-ram;
+ };
+
vmain_pd: regulator-0 {
/* TPS65988 PD CONTROLLER OUTPUT */
compatible = "regulator-fixed";
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi b/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
new file mode 100644
index 0000000000000..a9e372e9feada
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk-common.dtsi
@@ -0,0 +1,304 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Common dtsi for AM625 SK and derivatives
+ *
+ * Copyright (C) 2021-2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include "k3-am62x-sk-common.dtsi"
+
+/ {
+ opp-table {
+ /* Add 1.4GHz OPP for am625-sk board. Requires VDD_CORE to be at 0.85V */
+ opp-1400000000 {
+ opp-hz = /bits/ 64 <1400000000>;
+ opp-supported-hw = <0x01 0x0004>;
+ clock-latency-ns = <6000000>;
+ };
+ };
+
+ vmain_pd: regulator-0 {
+ /* TPS65988 PD CONTROLLER OUTPUT */
+ bootph-all;
+ compatible = "regulator-fixed";
+ regulator-name = "vmain_pd";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_5v0: regulator-1 {
+ /* Output of LM34936 */
+ bootph-all;
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vmain_pd>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_3v3_sys: regulator-2 {
+ /* output of LM61460-Q1 */
+ bootph-all;
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_sys";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vmain_pd>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: regulator-3 {
+ /* TPS22918DBVR */
+ bootph-all;
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vcc_3v3_sys>;
+ gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: regulator-4 {
+ /* Output of TLV71033 */
+ bootph-all;
+ compatible = "regulator-gpio";
+ regulator-name = "tlv71033";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vcc_5v0>;
+ gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+
+ vcc_1v8: regulator-5 {
+ /* output of TPS6282518DMQ */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&main_pmx0 {
+ main_mmc0_pins_default: main-mmc0-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
+ AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
+ AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
+ AM62X_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */
+ AM62X_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */
+ AM62X_IOPAD(0x208, PIN_INPUT_PULLUP, 0) /* (Y4) MMC0_DAT3 */
+ AM62X_IOPAD(0x204, PIN_INPUT_PULLUP, 0) /* (AB2) MMC0_DAT4 */
+ AM62X_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */
+ AM62X_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */
+ AM62X_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */
+ >;
+ };
+
+ main_rgmii2_pins_default: main-rgmii2-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
+ AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
+ AM62X_IOPAD(0x18c, PIN_INPUT, 0) /* (AC21) RGMII2_RD2 */
+ AM62X_IOPAD(0x190, PIN_INPUT, 0) /* (AE22) RGMII2_RD3 */
+ AM62X_IOPAD(0x180, PIN_INPUT, 0) /* (AD23) RGMII2_RXC */
+ AM62X_IOPAD(0x17c, PIN_INPUT, 0) /* (AD22) RGMII2_RX_CTL */
+ AM62X_IOPAD(0x16c, PIN_OUTPUT, 0) /* (Y18) RGMII2_TD0 */
+ AM62X_IOPAD(0x170, PIN_OUTPUT, 0) /* (AA18) RGMII2_TD1 */
+ AM62X_IOPAD(0x174, PIN_OUTPUT, 0) /* (AD21) RGMII2_TD2 */
+ AM62X_IOPAD(0x178, PIN_OUTPUT, 0) /* (AC20) RGMII2_TD3 */
+ AM62X_IOPAD(0x168, PIN_OUTPUT, 0) /* (AE21) RGMII2_TXC */
+ AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
+ >;
+ };
+
+ ospi0_pins_default: ospi0-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
+ AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
+ AM62X_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
+ AM62X_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
+ AM62X_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
+ AM62X_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
+ AM62X_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
+ AM62X_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
+ AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
+ AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
+ AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
+ >;
+ };
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
+ >;
+ };
+
+ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
+ >;
+ };
+};
+
+&main_gpio0 {
+ bootph-all;
+};
+
+&main_gpio1 {
+ bootph-all;
+};
+
+&main_i2c1 {
+ bootph-all;
+ exp1: gpio@22 {
+ bootph-all;
+ compatible = "ti,tca6424";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
+ "PRU_DETECT", "MMC1_SD_EN",
+ "VPP_LDO_EN", "EXP_PS_3V3_En",
+ "EXP_PS_5V0_En", "EXP_HAT_DETECT",
+ "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn",
+ "UART1_FET_BUF_EN", "WL_LT_EN",
+ "GPIO_HDMI_RSTn", "CSI_GPIO1",
+ "CSI_GPIO2", "PRU_3V3_EN",
+ "HDMI_INTn", "PD_I2C_IRQ",
+ "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
+ "MCASP1_FET_SEL", "UART1_FET_SEL",
+ "TSINT#", "IO_EXP_TEST_LED";
+
+ interrupt-parent = <&main_gpio1>;
+ interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+ };
+};
+
+&sdhci0 {
+ bootph-all;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc0_pins_default>;
+ status = "okay";
+};
+
+&sdhci1 {
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
+};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_rgmii1_pins_default>, <&main_rgmii2_pins_default>;
+};
+
+&cpsw_port2 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy1>;
+};
+
+&cpsw3g_mdio {
+ cpsw3g_phy1: ethernet-phy@1 {
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
+&fss {
+ bootph-all;
+};
+
+&ospi0 {
+ bootph-all;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ospi0_pins_default>;
+
+ flash@0 {
+ bootph-all;
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+
+ partitions {
+ bootph-all;
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ospi.tiboot3";
+ reg = <0x0 0x80000>;
+ };
+
+ partition@80000 {
+ label = "ospi.tispl";
+ reg = <0x80000 0x200000>;
+ };
+
+ partition@280000 {
+ label = "ospi.u-boot";
+ reg = <0x280000 0x400000>;
+ };
+
+ partition@680000 {
+ label = "ospi.env";
+ reg = <0x680000 0x40000>;
+ };
+
+ partition@6c0000 {
+ label = "ospi.env.backup";
+ reg = <0x6c0000 0x40000>;
+ };
+
+ partition@800000 {
+ label = "ospi.rootfs";
+ reg = <0x800000 0x37c0000>;
+ };
+
+ partition@3fc0000 {
+ bootph-pre-ram;
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ };
+ };
+ };
+};
+
+&tlv320aic3106 {
+ DVDD-supply = <&vcc_1v8>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index d240165bda9c5..52954c77df804 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -7,310 +7,17 @@
/dts-v1/;
-#include "k3-am62x-sk-common.dtsi"
+#include "k3-am625.dtsi"
+#include "k3-am625-sk-common.dtsi"
/ {
compatible = "ti,am625-sk", "ti,am625";
model = "Texas Instruments AM625 SK";
- opp-table {
- /* Add 1.4GHz OPP for am625-sk board. Requires VDD_CORE to be at 0.85V */
- opp-1400000000 {
- opp-hz = /bits/ 64 <1400000000>;
- opp-supported-hw = <0x01 0x0004>;
- clock-latency-ns = <6000000>;
- };
- };
-
memory@80000000 {
- device_type = "memory";
/* 2G RAM */
reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
-
- };
-
- vmain_pd: regulator-0 {
- /* TPS65988 PD CONTROLLER OUTPUT */
- bootph-all;
- compatible = "regulator-fixed";
- regulator-name = "vmain_pd";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- vcc_5v0: regulator-1 {
- /* Output of LM34936 */
- bootph-all;
- compatible = "regulator-fixed";
- regulator-name = "vcc_5v0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&vmain_pd>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- vcc_3v3_sys: regulator-2 {
- /* output of LM61460-Q1 */
- bootph-all;
- compatible = "regulator-fixed";
- regulator-name = "vcc_3v3_sys";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&vmain_pd>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- vdd_mmc1: regulator-3 {
- /* TPS22918DBVR */
- bootph-all;
- compatible = "regulator-fixed";
- regulator-name = "vdd_mmc1";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- enable-active-high;
- vin-supply = <&vcc_3v3_sys>;
- gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
- };
-
- vdd_sd_dv: regulator-4 {
- /* Output of TLV71033 */
- bootph-all;
- compatible = "regulator-gpio";
- regulator-name = "tlv71033";
- pinctrl-names = "default";
- pinctrl-0 = <&vdd_sd_dv_pins_default>;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- vin-supply = <&vcc_5v0>;
- gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
- states = <1800000 0x0>,
- <3300000 0x1>;
- };
-
- vcc_1v8: regulator-5 {
- /* output of TPS6282518DMQ */
- compatible = "regulator-fixed";
- regulator-name = "vcc_1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vcc_3v3_sys>;
- regulator-always-on;
- regulator-boot-on;
- };
-};
-
-&main_pmx0 {
- main_mmc0_pins_default: main-mmc0-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
- AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
- AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
- AM62X_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */
- AM62X_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */
- AM62X_IOPAD(0x208, PIN_INPUT_PULLUP, 0) /* (Y4) MMC0_DAT3 */
- AM62X_IOPAD(0x204, PIN_INPUT_PULLUP, 0) /* (AB2) MMC0_DAT4 */
- AM62X_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */
- AM62X_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */
- AM62X_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */
- >;
- };
-
- main_rgmii2_pins_default: main-rgmii2-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
- AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
- AM62X_IOPAD(0x18c, PIN_INPUT, 0) /* (AC21) RGMII2_RD2 */
- AM62X_IOPAD(0x190, PIN_INPUT, 0) /* (AE22) RGMII2_RD3 */
- AM62X_IOPAD(0x180, PIN_INPUT, 0) /* (AD23) RGMII2_RXC */
- AM62X_IOPAD(0x17c, PIN_INPUT, 0) /* (AD22) RGMII2_RX_CTL */
- AM62X_IOPAD(0x16c, PIN_OUTPUT, 0) /* (Y18) RGMII2_TD0 */
- AM62X_IOPAD(0x170, PIN_OUTPUT, 0) /* (AA18) RGMII2_TD1 */
- AM62X_IOPAD(0x174, PIN_OUTPUT, 0) /* (AD21) RGMII2_TD2 */
- AM62X_IOPAD(0x178, PIN_OUTPUT, 0) /* (AC20) RGMII2_TD3 */
- AM62X_IOPAD(0x168, PIN_OUTPUT, 0) /* (AE21) RGMII2_TXC */
- AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
- >;
- };
-
- ospi0_pins_default: ospi0-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
- AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
- AM62X_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
- AM62X_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
- AM62X_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
- AM62X_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
- AM62X_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
- AM62X_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
- AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
- AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
- AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
- >;
- };
-
- vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
- >;
- };
-
- main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
- >;
- };
-};
-
-&main_gpio0 {
- bootph-all;
-};
-
-&main_gpio1 {
- bootph-all;
-};
-
-&main_i2c1 {
- bootph-all;
- exp1: gpio@22 {
- bootph-all;
- compatible = "ti,tca6424";
- reg = <0x22>;
- gpio-controller;
- #gpio-cells = <2>;
- gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
- "PRU_DETECT", "MMC1_SD_EN",
- "VPP_LDO_EN", "EXP_PS_3V3_En",
- "EXP_PS_5V0_En", "EXP_HAT_DETECT",
- "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn",
- "UART1_FET_BUF_EN", "WL_LT_EN",
- "GPIO_HDMI_RSTn", "CSI_GPIO1",
- "CSI_GPIO2", "PRU_3V3_EN",
- "HDMI_INTn", "PD_I2C_IRQ",
- "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
- "MCASP1_FET_SEL", "UART1_FET_SEL",
- "TSINT#", "IO_EXP_TEST_LED";
-
- interrupt-parent = <&main_gpio1>;
- interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
- };
-};
-
-&sdhci0 {
- bootph-all;
- non-removable;
- pinctrl-names = "default";
- pinctrl-0 = <&main_mmc0_pins_default>;
- status = "okay";
-};
-
-&sdhci1 {
- vmmc-supply = <&vdd_mmc1>;
- vqmmc-supply = <&vdd_sd_dv>;
-};
-
-&cpsw3g {
- pinctrl-names = "default";
- pinctrl-0 = <&main_rgmii1_pins_default>, <&main_rgmii2_pins_default>;
-};
-
-&cpsw_port2 {
- phy-mode = "rgmii-rxid";
- phy-handle = <&cpsw3g_phy1>;
-};
-
-&cpsw3g_mdio {
- cpsw3g_phy1: ethernet-phy@1 {
- reg = <1>;
- ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
- ti,min-output-impedance;
- };
-};
-
-&fss {
- bootph-all;
-};
-
-&ospi0 {
- bootph-all;
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&ospi0_pins_default>;
-
- flash@0 {
- bootph-all;
- compatible = "jedec,spi-nor";
- reg = <0x0>;
- spi-tx-bus-width = <8>;
- spi-rx-bus-width = <8>;
- spi-max-frequency = <25000000>;
- cdns,tshsl-ns = <60>;
- cdns,tsd2d-ns = <60>;
- cdns,tchsh-ns = <60>;
- cdns,tslch-ns = <60>;
- cdns,read-delay = <4>;
-
- partitions {
- bootph-all;
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "ospi.tiboot3";
- reg = <0x0 0x80000>;
- };
-
- partition@80000 {
- label = "ospi.tispl";
- reg = <0x80000 0x200000>;
- };
-
- partition@280000 {
- label = "ospi.u-boot";
- reg = <0x280000 0x400000>;
- };
-
- partition@680000 {
- label = "ospi.env";
- reg = <0x680000 0x40000>;
- };
-
- partition@6c0000 {
- label = "ospi.env.backup";
- reg = <0x6c0000 0x40000>;
- };
-
- partition@800000 {
- label = "ospi.rootfs";
- reg = <0x800000 0x37c0000>;
- };
-
- partition@3fc0000 {
- bootph-pre-ram;
- label = "ospi.phypattern";
- reg = <0x3fc0000 0x40000>;
- };
- };
+ device_type = "memory";
+ bootph-pre-ram;
};
};
-
-&tlv320aic3106 {
- DVDD-supply = <&vcc_1v8>;
-};
diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
index 9d45d8dad381e..be5cc73cf2e4b 100644
--- a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
@@ -8,7 +8,6 @@
#include <dt-bindings/leds/common.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/net/ti-dp83867.h>
-#include "k3-am625.dtsi"
/ {
aliases {
@@ -27,13 +26,6 @@ chosen {
stdout-path = "serial2:115200n8";
};
- memory@80000000 {
- bootph-pre-ram;
- device_type = "memory";
- /* 2G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
- };
-
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
--
2.53.0
^ permalink raw reply related [flat|nested] 4+ messages in thread