* [U-Boot] [PATCH V2 1/2] GPIO: Tegra2: add GPIO driver for Tegra2
2011-05-02 22:45 [U-Boot] [PATCH V2 0/2] GPIO: Tegra2: add GPIO driver for Tegra2 Tom Warren
@ 2011-05-02 22:45 ` Tom Warren
2011-05-02 23:15 ` Mike Frysinger
2011-05-02 22:45 ` [U-Boot] [PATCH V2 2/2] arm: Tegra2: GPIO: enable GPIO for Tegra2 boards Tom Warren
1 sibling, 1 reply; 5+ messages in thread
From: Tom Warren @ 2011-05-02 22:45 UTC (permalink / raw)
To: u-boot
Signed-off-by: Tom Warren <twarren@nvidia.com>
---
Changes in V2:
- use 'gpio_pin' enum in gpio.h (Simon Glass review request)
- change 'GPIO_PORT8' to 'GPIO_FULLPORT' (Simon Glass request)
- change 'offset' to 'pin' globally
arch/arm/include/asm/arch-tegra2/gpio.h | 244 ++++++++++++++++++++++++-
drivers/gpio/Makefile | 1 +
drivers/gpio/tegra2_gpio.c | 299 +++++++++++++++++++++++++++++++
3 files changed, 537 insertions(+), 7 deletions(-)
create mode 100644 drivers/gpio/tegra2_gpio.c
diff --git a/arch/arm/include/asm/arch-tegra2/gpio.h b/arch/arm/include/asm/arch-tegra2/gpio.h
index 0fb8f0d..e55305a 100644
--- a/arch/arm/include/asm/arch-tegra2/gpio.h
+++ b/arch/arm/include/asm/arch-tegra2/gpio.h
@@ -45,15 +45,245 @@ struct gpio_ctlr {
struct gpio_ctlr_bank gpio_bank[TEGRA_GPIO_BANKS];
};
-#define GPIO_BANK(x) ((x) >> 5)
-#define GPIO_PORT(x) (((x) >> 3) & 0x3)
-#define GPIO_BIT(x) ((x) & 0x7)
+#define GPIO_BANK(x) ((x) >> 5)
+#define GPIO_PORT(x) (((x) >> 3) & 0x3)
+#define GPIO_FULLPORT(x) ((x) >> 3)
+#define GPIO_BIT(x) ((x) & 0x7)
+
+enum gpio_pin {
+ GPIO_PA0 = 0, /* pin 0 */
+ GPIO_PA1,
+ GPIO_PA2,
+ GPIO_PA3,
+ GPIO_PA4,
+ GPIO_PA5,
+ GPIO_PA6,
+ GPIO_PA7,
+ GPIO_PB0, /* pin 8 */
+ GPIO_PB1,
+ GPIO_PB2,
+ GPIO_PB3,
+ GPIO_PB4,
+ GPIO_PB5,
+ GPIO_PB6,
+ GPIO_PB7,
+ GPIO_PC0, /* pin 16 */
+ GPIO_PC1,
+ GPIO_PC2,
+ GPIO_PC3,
+ GPIO_PC4,
+ GPIO_PC5,
+ GPIO_PC6,
+ GPIO_PC7,
+ GPIO_PD0, /* pin 24 */
+ GPIO_PD1,
+ GPIO_PD2,
+ GPIO_PD3,
+ GPIO_PD4,
+ GPIO_PD5,
+ GPIO_PD6,
+ GPIO_PD7,
+ GPIO_PE0, /* pin 32 */
+ GPIO_PE1,
+ GPIO_PE2,
+ GPIO_PE3,
+ GPIO_PE4,
+ GPIO_PE5,
+ GPIO_PE6,
+ GPIO_PE7,
+ GPIO_PF0, /* pin 40 */
+ GPIO_PF1,
+ GPIO_PF2,
+ GPIO_PF3,
+ GPIO_PF4,
+ GPIO_PF5,
+ GPIO_PF6,
+ GPIO_PF7,
+ GPIO_PG0, /* pin 48 */
+ GPIO_PG1,
+ GPIO_PG2,
+ GPIO_PG3,
+ GPIO_PG4,
+ GPIO_PG5,
+ GPIO_PG6,
+ GPIO_PG7,
+ GPIO_PH0, /* pin 56 */
+ GPIO_PH1,
+ GPIO_PH2,
+ GPIO_PH3,
+ GPIO_PH4,
+ GPIO_PH5,
+ GPIO_PH6,
+ GPIO_PH7,
+ GPIO_PI0, /* pin 64 */
+ GPIO_PI1,
+ GPIO_PI2,
+ GPIO_PI3,
+ GPIO_PI4,
+ GPIO_PI5,
+ GPIO_PI6,
+ GPIO_PI7,
+ GPIO_PJ0, /* pin 72 */
+ GPIO_PJ1,
+ GPIO_PJ2,
+ GPIO_PJ3,
+ GPIO_PJ4,
+ GPIO_PJ5,
+ GPIO_PJ6,
+ GPIO_PJ7,
+ GPIO_PK0, /* pin 80 */
+ GPIO_PK1,
+ GPIO_PK2,
+ GPIO_PK3,
+ GPIO_PK4,
+ GPIO_PK5,
+ GPIO_PK6,
+ GPIO_PK7,
+ GPIO_PL0, /* pin 88 */
+ GPIO_PL1,
+ GPIO_PL2,
+ GPIO_PL3,
+ GPIO_PL4,
+ GPIO_PL5,
+ GPIO_PL6,
+ GPIO_PL7,
+ GPIO_PM0, /* pin 96 */
+ GPIO_PM1,
+ GPIO_PM2,
+ GPIO_PM3,
+ GPIO_PM4,
+ GPIO_PM5,
+ GPIO_PM6,
+ GPIO_PM7,
+ GPIO_PN0, /* pin 104 */
+ GPIO_PN1,
+ GPIO_PN2,
+ GPIO_PN3,
+ GPIO_PN4,
+ GPIO_PN5,
+ GPIO_PN6,
+ GPIO_PN7,
+ GPIO_PO0, /* pin 112 */
+ GPIO_PO1,
+ GPIO_PO2,
+ GPIO_PO3,
+ GPIO_PO4,
+ GPIO_PO5,
+ GPIO_PO6,
+ GPIO_PO7,
+ GPIO_PP0, /* pin 120 */
+ GPIO_PP1,
+ GPIO_PP2,
+ GPIO_PP3,
+ GPIO_PP4,
+ GPIO_PP5,
+ GPIO_PP6,
+ GPIO_PP7,
+ GPIO_PQ0, /* pin 128 */
+ GPIO_PQ1,
+ GPIO_PQ2,
+ GPIO_PQ3,
+ GPIO_PQ4,
+ GPIO_PQ5,
+ GPIO_PQ6,
+ GPIO_PQ7,
+ GPIO_PR0, /* pin 136 */
+ GPIO_PR1,
+ GPIO_PR2,
+ GPIO_PR3,
+ GPIO_PR4,
+ GPIO_PR5,
+ GPIO_PR6,
+ GPIO_PR7,
+ GPIO_PS0, /* pin 144 */
+ GPIO_PS1,
+ GPIO_PS2,
+ GPIO_PS3,
+ GPIO_PS4,
+ GPIO_PS5,
+ GPIO_PS6,
+ GPIO_PS7,
+ GPIO_PT0, /* pin 152 */
+ GPIO_PT1,
+ GPIO_PT2,
+ GPIO_PT3,
+ GPIO_PT4,
+ GPIO_PT5,
+ GPIO_PT6,
+ GPIO_PT7,
+ GPIO_PU0, /* pin 160 */
+ GPIO_PU1,
+ GPIO_PU2,
+ GPIO_PU3,
+ GPIO_PU4,
+ GPIO_PU5,
+ GPIO_PU6,
+ GPIO_PU7,
+ GPIO_PV0, /* pin 168 */
+ GPIO_PV1,
+ GPIO_PV2,
+ GPIO_PV3,
+ GPIO_PV4,
+ GPIO_PV5,
+ GPIO_PV6,
+ GPIO_PV7,
+ GPIO_PW0, /* pin 176 */
+ GPIO_PW1,
+ GPIO_PW2,
+ GPIO_PW3,
+ GPIO_PW4,
+ GPIO_PW5,
+ GPIO_PW6,
+ GPIO_PW7,
+ GPIO_PX0, /* pin 184 */
+ GPIO_PX1,
+ GPIO_PX2,
+ GPIO_PX3,
+ GPIO_PX4,
+ GPIO_PX5,
+ GPIO_PX6,
+ GPIO_PX7,
+ GPIO_PY0, /* pin 192 */
+ GPIO_PY1,
+ GPIO_PY2,
+ GPIO_PY3,
+ GPIO_PY4,
+ GPIO_PY5,
+ GPIO_PY6,
+ GPIO_PY7,
+ GPIO_PZ0, /* pin 200 */
+ GPIO_PZ1,
+ GPIO_PZ2,
+ GPIO_PZ3,
+ GPIO_PZ4,
+ GPIO_PZ5,
+ GPIO_PZ6,
+ GPIO_PZ7,
+ GPIO_PAA0, /* pin 208 */
+ GPIO_PAA1,
+ GPIO_PAA2,
+ GPIO_PAA3,
+ GPIO_PAA4,
+ GPIO_PAA5,
+ GPIO_PAA6,
+ GPIO_PAA7,
+ GPIO_PBB0, /* pin 216 */
+ GPIO_PBB1,
+ GPIO_PBB2,
+ GPIO_PBB3,
+ GPIO_PBB4,
+ GPIO_PBB5,
+ GPIO_PBB6,
+ GPIO_PBB7, /* pin 223 */
+};
/*
- * GPIO_PI3 = Port I = 8, bit = 3.
- * Seaboard: used for UART/SPI selection
- * Harmony: not used
+ * Tegra2-specific GPIO API
*/
-#define GPIO_PI3 ((8 << 3) | 3)
+
+int gpio_direction_input(int gp);
+int gpio_direction_output(int gp, int value);
+int gpio_get_value(int gp);
+void gpio_set_value(int gp, int value);
#endif /* TEGRA2_GPIO_H_ */
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index a5fa2b5..1e3ae11 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -31,6 +31,7 @@ COBJS-$(CONFIG_MARVELL_MFP) += mvmfp.o
COBJS-$(CONFIG_MXC_GPIO) += mxc_gpio.o
COBJS-$(CONFIG_PCA953X) += pca953x.o
COBJS-$(CONFIG_S5P) += s5p_gpio.o
+COBJS-$(CONFIG_TEGRA2_GPIO) += tegra2_gpio.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
diff --git a/drivers/gpio/tegra2_gpio.c b/drivers/gpio/tegra2_gpio.c
new file mode 100644
index 0000000..9090579
--- /dev/null
+++ b/drivers/gpio/tegra2_gpio.c
@@ -0,0 +1,299 @@
+/*
+ * NVIDIA Tegra2 GPIO handling.
+ * (C) Copyright 2010,2011
+ * NVIDIA Corporation <www.nvidia.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Based on (mostly copied from) kw_gpio.c based Linux 2.6 kernel driver.
+ * Tom Warren (twarren at nvidia.com)
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/bitops.h>
+#include <asm/arch/tegra2.h>
+#include <asm/arch/gpio.h>
+
+enum {
+ TEGRA2_CMD_INFO,
+ TEGRA2_CMD_PORT,
+ TEGRA2_CMD_OUTPUT,
+ TEGRA2_CMD_INPUT,
+};
+
+/* Config pin 'gp' as GPIO or SFPIO, based on 'type' */
+void __set_config(int gp, int type)
+{
+ struct gpio_ctlr *gpio = (struct gpio_ctlr *)NV_PA_GPIO_BASE;
+ struct gpio_ctlr_bank *bank = &gpio->gpio_bank[GPIO_BANK(gp)];
+ u32 u;
+
+ debug("__set_config: port = %d, bit = %d, %s\n",
+ GPIO_FULLPORT(gp), GPIO_BIT(gp), type ? "GPIO" : "SFPIO");
+
+ u = readl(&bank->gpio_config[GPIO_PORT(gp)]);
+ if (type) /* GPIO */
+ u |= 1 << GPIO_BIT(gp);
+ else
+ u &= ~(1 << GPIO_BIT(gp));
+ writel(u, &bank->gpio_config[GPIO_PORT(gp)]);
+}
+
+/* Config GPIO pin 'gp' as input or output (OE) as per 'output' */
+void __set_direction(int gp, int output)
+{
+ struct gpio_ctlr *gpio = (struct gpio_ctlr *)NV_PA_GPIO_BASE;
+ struct gpio_ctlr_bank *bank = &gpio->gpio_bank[GPIO_BANK(gp)];
+ u32 u;
+
+ debug("__set_direction: port = %d, bit = %d, %s\n",
+ GPIO_FULLPORT(gp), GPIO_BIT(gp), output ? "OUT" : "IN");
+
+ u = readl(&bank->gpio_dir_out[GPIO_PORT(gp)]);
+ if (output)
+ u |= 1 << GPIO_BIT(gp);
+ else
+ u &= ~(1 << GPIO_BIT(gp));
+ writel(u, &bank->gpio_dir_out[GPIO_PORT(gp)]);
+}
+
+/* set GPIO pin 'gp' output bit as 0 or 1 as per 'high' */
+void __set_level(int gp, int high)
+{
+ struct gpio_ctlr *gpio = (struct gpio_ctlr *)NV_PA_GPIO_BASE;
+ struct gpio_ctlr_bank *bank = &gpio->gpio_bank[GPIO_BANK(gp)];
+ u32 u;
+
+ debug("__set_level: port = %d, bit %d == %d\n",
+ GPIO_FULLPORT(gp), GPIO_BIT(gp), high);
+
+ u = readl(&bank->gpio_out[GPIO_PORT(gp)]);
+ if (high)
+ u |= 1 << GPIO_BIT(gp);
+ else
+ u &= ~(1 << GPIO_BIT(gp));
+ writel(u, &bank->gpio_out[GPIO_PORT(gp)]);
+}
+
+/*
+ * GENERIC_GPIO primitives.
+ */
+
+/* set GPIO pin 'gp' as an input */
+int gpio_direction_input(int gp)
+{
+ debug("gpio_direction_input: pin = %d (port %d:bit %d)\n",
+ gp, GPIO_FULLPORT(gp), GPIO_BIT(gp));
+
+ /* Configure as a GPIO */
+ __set_config(gp, 1);
+
+ /* Configure GPIO direction as input. */
+ __set_direction(gp, 0);
+
+ return 0;
+}
+
+/* set GPIO pin 'gp' as an output, with polarity 'value' */
+int gpio_direction_output(int gp, int value)
+{
+ debug("gpio_direction_output: pin = %d (port %d:bit %d) = %s\n",
+ gp, GPIO_FULLPORT(gp), GPIO_BIT(gp), value ? "HIGH" : "LOW");
+
+ /* Configure as a GPIO */
+ __set_config(gp, 1);
+
+ /* Configure GPIO output value. */
+ __set_level(gp, value);
+
+ /* Configure GPIO direction as output. */
+ __set_direction(gp, 1);
+
+ return 0;
+}
+
+/* read GPIO IN value of pin 'gp' */
+int gpio_get_value(int gp)
+{
+ struct gpio_ctlr *gpio = (struct gpio_ctlr *)NV_PA_GPIO_BASE;
+ struct gpio_ctlr_bank *bank = &gpio->gpio_bank[GPIO_BANK(gp)];
+ int val;
+
+ debug("gpio_get_value: pin = %d (port %d:bit %d)\n",
+ gp, GPIO_FULLPORT(gp), GPIO_BIT(gp));
+
+ val = readl(&bank->gpio_in[GPIO_PORT(gp)]);
+
+ return (val >> GPIO_BIT(gp)) & 1;
+}
+
+/* write GPIO OUT value to pin 'gp' */
+void gpio_set_value(int gp, int value)
+{
+ debug("gpio_set_value: pin = %d (port %d:bit %d), value = %d\n",
+ gp, GPIO_FULLPORT(gp), GPIO_BIT(gp), value);
+
+ /* Configure GPIO output value. */
+ __set_level(gp, value);
+}
+
+#ifdef CONFIG_CMD_TEGRA2_GPIO_INFO
+/*
+ * Display Tegra GPIO information
+ */
+static int gpio_info(int gp)
+{
+ struct gpio_ctlr *gpio = (struct gpio_ctlr *)NV_PA_GPIO_BASE;
+ struct gpio_ctlr_bank *bank = &gpio->gpio_bank[GPIO_BANK(gp)];
+ int i, port;
+ u32 data;
+
+ port = GPIO_FULLPORT(gp); /* 8-bit port # */
+
+ printf("Tegra2 GPIO port %d:\n\n", port);
+ printf("gpio bits: 76543210\n");
+ printf("-------------------\n");
+
+ if (port < 0 || port > 27)
+ return -1;
+
+ printf("GPIO_CNF: ");
+ data = readl(&bank->gpio_config[GPIO_PORT(gp)]);
+ for (i = 7; i >= 0; i--)
+ printf("%c", data & (1 << i) ? 'g' : 's');
+ printf("\n");
+
+ printf("GPIO_OE: ");
+ data = readl(&bank->gpio_dir_out[GPIO_PORT(gp)]);
+ for (i = 7; i >= 0; i--)
+ printf("%c", data & (1 << i) ? 'o' : 'i');
+ printf("\n");
+
+ printf("GPIO_IN: ");
+ data = readl(&bank->gpio_in[GPIO_PORT(gp)]);
+ for (i = 7; i >= 0; i--)
+ printf("%c", data & (1 << i) ? '1' : '0');
+ printf("\n");
+
+ printf("GPIO_OUT: ");
+ data = readl(&bank->gpio_out[GPIO_PORT(gp)]);
+ for (i = 7; i >= 0; i--)
+ printf("%c", data & (1 << i) ? '1' : '0');
+ printf("\n");
+
+ return 0;
+}
+#endif /* CONFIG_CMD_TEGRA2_GPIO_INFO */
+
+cmd_tbl_t cmd_gpio[] = {
+ U_BOOT_CMD_MKENT(pin2port, 3, 0, (void *)TEGRA2_CMD_PORT, "", ""),
+ U_BOOT_CMD_MKENT(output, 4, 0, (void *)TEGRA2_CMD_OUTPUT, "", ""),
+ U_BOOT_CMD_MKENT(input, 3, 0, (void *)TEGRA2_CMD_INPUT, "", ""),
+#ifdef CONFIG_CMD_TEGRA2_GPIO_INFO
+ U_BOOT_CMD_MKENT(info, 3, 0, (void *)TEGRA2_CMD_INFO, "", ""),
+#endif
+};
+
+int do_gpio(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ static uint8_t pin;
+ int val, port, bit;
+ ulong ul_arg2, ul_arg3, ul_arg4;
+ cmd_tbl_t *c;
+
+ ul_arg2 = ul_arg3 = ul_arg4 = 0;
+
+ c = find_cmd_tbl(argv[1], cmd_gpio, ARRAY_SIZE(cmd_gpio));
+
+ /* All commands but "port" require 'maxargs' arguments */
+ if (!c || !((argc == (c->maxargs)) ||
+ (((int)c->cmd == TEGRA2_CMD_PORT) &&
+ (argc == (c->maxargs - 1))))) {
+ cmd_usage(cmdtp);
+ return 1;
+ }
+
+ /* arg2 used as pin */
+ if (argc > 2)
+ ul_arg2 = simple_strtoul(argv[2], NULL, 10);
+
+ /* arg3 used as output value, 0 or 1 */
+ if (argc > 3)
+ ul_arg3 = simple_strtoul(argv[3], NULL, 10) & 0x1;
+
+ switch ((int)c->cmd) {
+#ifdef CONFIG_CMD_TEGRA2_GPIO_INFO
+ case TEGRA2_CMD_INFO:
+ if (argc == 3)
+ pin = (uint8_t)ul_arg2;
+ return gpio_info(pin);
+
+#endif
+ case TEGRA2_CMD_PORT:
+ if (argc == 3)
+ pin = (uint8_t)ul_arg2;
+ port = GPIO_FULLPORT(pin);
+ bit = GPIO_BIT(pin);
+ printf("pin %d = port # %d, bit # %d\n",
+ pin, port, bit);
+ return 0;
+
+ case TEGRA2_CMD_INPUT:
+ /* arg2 = pin */
+ port = GPIO_FULLPORT(pin);
+ bit = GPIO_BIT(pin);
+ gpio_direction_input(ul_arg2);
+ val = gpio_get_value(ul_arg2);
+
+ printf("pin %lu (port:bit %d:%d) = %d\n",
+ ul_arg2, port, bit, val);
+ return 0;
+
+ case TEGRA2_CMD_OUTPUT:
+ /* args = pin, value */
+ port = GPIO_FULLPORT(pin);
+ bit = GPIO_BIT(pin);
+ gpio_direction_output(ul_arg2, ul_arg3);
+ printf("pin %lu (port:bit %d:%d) = %ld\n",
+ ul_arg2, port, bit, ul_arg3);
+ return 0;
+
+ default:
+ /* We should never get here */
+ return 1;
+ }
+}
+
+U_BOOT_CMD(
+ gpio, 5, 1, do_gpio,
+ "GPIO access",
+ "pin2port pin\n"
+ " - show GPIO port:bit based on 'pin'\n"
+#ifdef CONFIG_CMD_TEGRA2_GPIO_INFO
+ " info pin\n"
+ " - display info for all bits in port based on 'pin'\n"
+#endif
+ " output pin 0|1\n"
+ " - using 'pin', set port:bit as output and drive low or high\n"
+ " input pin\n"
+ " - using 'pin', set port:bit as input and read value"
+);
--
1.7.5
^ permalink raw reply related [flat|nested] 5+ messages in thread