* [U-Boot] uboot for zyxel nsa320 @ 2012-07-13 17:43 kqt4at5v at gmail.com 2012-07-13 23:20 ` Luka Perkov 0 siblings, 1 reply; 5+ messages in thread From: kqt4at5v at gmail.com @ 2012-07-13 17:43 UTC (permalink / raw) To: u-boot I have a new Zyxel NSA320. It is unmodified. At the uboot prompt I printenv and save all environment variables. Next I pulled code from https://github.com/psch2/uboot-nsa320, compiled and used kwboot to load new uboot. No problems so far. Now if I reload all environment variables I saved and boot the kernel loads but does not execute. Any ideas? NSA320> boot NAND read: device 0 offset 0xc80000, size 0xa00000 10485760 bytes read: OK ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-2.6.31.8 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5909960 Bytes = 5.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................................................................................................................................................................... done, booting the kernel. Richard ^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] uboot for zyxel nsa320 2012-07-13 17:43 [U-Boot] uboot for zyxel nsa320 kqt4at5v at gmail.com @ 2012-07-13 23:20 ` Luka Perkov 2012-07-14 9:51 ` kqt4at5v at gmail.com 0 siblings, 1 reply; 5+ messages in thread From: Luka Perkov @ 2012-07-13 23:20 UTC (permalink / raw) To: u-boot Hi, On Fri, Jul 13, 2012 at 12:43:13PM -0500, kqt4at5v at gmail.com wrote: > I have a new Zyxel NSA320. It is unmodified. At the uboot prompt I > printenv and save all environment variables. Next I pulled code from > https://github.com/psch2/uboot-nsa320, compiled and used kwboot to > load new uboot. No problems so far. Now if I reload all environment > variables I saved and boot the kernel loads but does not execute. > Any ideas? > > NSA320> boot > > NAND read: device 0 offset 0xc80000, size 0xa00000 > 10485760 bytes read: OK > ## Booting kernel from Legacy Image at 02000000 ... > Image Name: Linux-2.6.31.8 > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 5909960 Bytes = 5.6 MiB > Load Address: 00008000 > Entry Point: 00008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Uncompressing Linux............................................................................................................................................................................................................................................................................... > done, booting the kernel. You are probably missing console=ttyS0,115200 in your bootargs environment variable. What is the output of "printenv" ? Luka ^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] uboot for zyxel nsa320 2012-07-13 23:20 ` Luka Perkov @ 2012-07-14 9:51 ` kqt4at5v at gmail.com 2012-07-14 18:47 ` Luka Perkov 0 siblings, 1 reply; 5+ messages in thread From: kqt4at5v at gmail.com @ 2012-07-14 9:51 UTC (permalink / raw) To: u-boot On Sat, 14 Jul 2012, Luka Perkov wrote: > Hi, > > On Fri, Jul 13, 2012 at 12:43:13PM -0500, kqt4at5v at gmail.com wrote: >> I have a new Zyxel NSA320. It is unmodified. At the uboot prompt I >> printenv and save all environment variables. Next I pulled code from >> https://github.com/psch2/uboot-nsa320, compiled and used kwboot to >> load new uboot. No problems so far. Now if I reload all environment >> variables I saved and boot the kernel loads but does not execute. >> Any ideas? >> >> NSA320> boot >> >> NAND read: device 0 offset 0xc80000, size 0xa00000 >> 10485760 bytes read: OK >> ## Booting kernel from Legacy Image at 02000000 ... >> Image Name: Linux-2.6.31.8 >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 5909960 Bytes = 5.6 MiB >> Load Address: 00008000 >> Entry Point: 00008000 >> Verifying Checksum ... OK >> Loading Kernel Image ... OK >> OK >> >> Starting kernel ... >> >> Uncompressing Linux............................................................................................................................................................................................................................................................................... >> done, booting the kernel. > > You are probably missing console=ttyS0,115200 in your bootargs > environment variable. What is the output of "printenv" ? > NSA320>> printenv bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000 bootdelay=2 baudrate=115200 loads_echo=0 eth1addr=00:19:CB:00:51:82 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 nandEcc=1bit MODEL_ID=DD01 PRODUCT_NAME=NSA-320 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=ZyXEL Communications Corp. run_diag=yes ethaddr=C8:6C:87:F8:3D:84 stdin=serial stdout=serial stderr=serial console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000 at 0(uboot)ro,0x7f00000 at 0x100000(root) mainlineLinux=no CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes ethprime=egiga1 netbsd_en=no vxworks_en=no bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; disaMvPnp=no ethmtu=1500 eth1mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 hddPowerCtrl=no netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no enaAutoRecovery=yes kernel_addr=0xc80000 pcieTune=no ethact=egiga1 Environment size: 1557/131068 bytes ^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] uboot for zyxel nsa320 2012-07-14 9:51 ` kqt4at5v at gmail.com @ 2012-07-14 18:47 ` Luka Perkov 2012-07-14 18:53 ` kqt4at5v at gmail.com 0 siblings, 1 reply; 5+ messages in thread From: Luka Perkov @ 2012-07-14 18:47 UTC (permalink / raw) To: u-boot Hi kqt4at5v, On Sat, Jul 14, 2012 at 04:51:13AM -0500, kqt4at5v at gmail.com wrote: > NSA320>> printenv > bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init > bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000 > bootdelay=2 > baudrate=115200 > loads_echo=0 > eth1addr=00:19:CB:00:51:82 > ipaddr=10.4.50.165 > serverip=10.4.50.5 > rootpath=/mnt/ARM_FS/ > netmask=255.255.255.0 > nandEcc=1bit > MODEL_ID=DD01 > PRODUCT_NAME=NSA-320 > FEATURE_BIT=00 > CONTRY_TYPE=FF > VENDOR_NAME=ZyXEL Communications Corp. This is not from official uboot. Either your kernel that you are trying to boot is is not good or you did not set serial output correctly. Luka ^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] uboot for zyxel nsa320 2012-07-14 18:47 ` Luka Perkov @ 2012-07-14 18:53 ` kqt4at5v at gmail.com 0 siblings, 0 replies; 5+ messages in thread From: kqt4at5v at gmail.com @ 2012-07-14 18:53 UTC (permalink / raw) To: u-boot On Sat, 14 Jul 2012, Luka Perkov wrote: > Hi kqt4at5v, > > On Sat, Jul 14, 2012 at 04:51:13AM -0500, kqt4at5v at gmail.com wrote: >> NSA320>> printenv >> bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init >> bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000 >> bootdelay=2 >> baudrate=115200 >> loads_echo=0 >> eth1addr=00:19:CB:00:51:82 >> ipaddr=10.4.50.165 >> serverip=10.4.50.5 >> rootpath=/mnt/ARM_FS/ >> netmask=255.255.255.0 >> nandEcc=1bit >> MODEL_ID=DD01 >> PRODUCT_NAME=NSA-320 >> FEATURE_BIT=00 >> CONTRY_TYPE=FF >> VENDOR_NAME=ZyXEL Communications Corp. > > This is not from official uboot. > > Either your kernel that you are trying to boot is is not good or you did > not set serial output correctly. > These variables are from the version of uboot that comes installed on the Zyxel NSA320. It works ok but any other version of uboot does not. I would like to fix that but I do not know how to trouble shoot this. Richard ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-07-14 18:53 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2012-07-13 17:43 [U-Boot] uboot for zyxel nsa320 kqt4at5v at gmail.com 2012-07-13 23:20 ` Luka Perkov 2012-07-14 9:51 ` kqt4at5v at gmail.com 2012-07-14 18:47 ` Luka Perkov 2012-07-14 18:53 ` kqt4at5v at gmail.com
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox