From: Patrice CHOTARD <patrice.chotard@st.com>
To: u-boot@lists.denx.de
Subject: [PATCH v2 09/11] gpio: stmfx: add ops get_dir_flags
Date: Thu, 2 Jul 2020 07:58:45 +0000 [thread overview]
Message-ID: <7c313cec-1573-aa2b-20c6-eaa192bb721d@st.com> (raw)
In-Reply-To: <20200604143022.v2.9.I375f10587b02d30722492fc1101aaf214c8a873b@changeid>
Hi Patrick
On 6/4/20 2:30 PM, Patrick Delaunay wrote:
> Add support of ops get_dir_flags() to read dir flags from
> STMFX registers.
>
> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
> ---
>
> Changes in v2: None
>
> drivers/pinctrl/pinctrl-stmfx.c | 50 +++++++++++++++++++++++++++++++++
> 1 file changed, 50 insertions(+)
>
> diff --git a/drivers/pinctrl/pinctrl-stmfx.c b/drivers/pinctrl/pinctrl-stmfx.c
> index 88df9e61a7..1d326ecf17 100644
> --- a/drivers/pinctrl/pinctrl-stmfx.c
> +++ b/drivers/pinctrl/pinctrl-stmfx.c
> @@ -108,12 +108,22 @@ static int stmfx_conf_set_pupd(struct udevice *dev, unsigned int offset,
> return stmfx_write_reg(dev, STMFX_REG_GPIO_PUPD, offset, pupd);
> }
>
> +static int stmfx_conf_get_pupd(struct udevice *dev, unsigned int offset)
> +{
> + return stmfx_read_reg(dev, STMFX_REG_GPIO_PUPD, offset);
> +}
> +
> static int stmfx_conf_set_type(struct udevice *dev, unsigned int offset,
> uint type)
> {
> return stmfx_write_reg(dev, STMFX_REG_GPIO_TYPE, offset, type);
> }
>
> +static int stmfx_conf_get_type(struct udevice *dev, unsigned int offset)
> +{
> + return stmfx_read_reg(dev, STMFX_REG_GPIO_TYPE, offset);
> +}
> +
> static int stmfx_gpio_get(struct udevice *dev, unsigned int offset)
> {
> return stmfx_read_reg(dev, STMFX_REG_GPIO_STATE, offset);
> @@ -189,6 +199,45 @@ static int stmfx_gpio_set_dir_flags(struct udevice *dev, unsigned int offset,
> return ret;
> }
>
> +static int stmfx_gpio_get_dir_flags(struct udevice *dev, unsigned int offset,
> + ulong *flags)
> +{
> + ulong dir_flags = 0;
> + int ret;
> +
> + if (stmfx_gpio_get_function(dev, offset) == GPIOF_OUTPUT) {
> + dir_flags |= GPIOD_IS_OUT;
> + ret = stmfx_conf_get_type(dev, offset);
> + if (ret < 0)
> + return ret;
> + if (ret == 0)
> + dir_flags |= GPIOD_OPEN_DRAIN;
> + /* 1 = push-pull (default), open source not supported */
> + ret = stmfx_gpio_get(dev, offset);
> + if (ret < 0)
> + return ret;
> + if (ret)
> + dir_flags |= GPIOD_IS_OUT_ACTIVE;
> + } else {
> + dir_flags |= GPIOD_IS_IN;
> + ret = stmfx_conf_get_type(dev, offset);
> + if (ret < 0)
> + return ret;
> + if (ret == 1) {
> + ret = stmfx_conf_get_pupd(dev, offset);
> + if (ret < 0)
> + return ret;
> + if (ret == 1)
> + dir_flags |= GPIOD_PULL_UP;
> + else
> + dir_flags |= GPIOD_PULL_DOWN;
> + }
> + }
> + *flags = dir_flags;
> +
> + return 0;
> +}
> +
> static int stmfx_gpio_probe(struct udevice *dev)
> {
> struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
> @@ -218,6 +267,7 @@ static const struct dm_gpio_ops stmfx_gpio_ops = {
> .direction_input = stmfx_gpio_direction_input,
> .direction_output = stmfx_gpio_direction_output,
> .set_dir_flags = stmfx_gpio_set_dir_flags,
> + .get_dir_flags = stmfx_gpio_get_dir_flags,
> };
>
> U_BOOT_DRIVER(stmfx_gpio) = {
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Thanks
next prev parent reply other threads:[~2020-07-02 7:58 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-04 12:30 [PATCH v2 00/11] stm32mp1: activate gpio hog support and add new pinctrl ops Patrick Delaunay
2020-06-04 12:30 ` [PATCH v2 01/11] configs: stm32mp1: activate CONFIG_GPIO_HOG Patrick Delaunay
2020-07-02 7:41 ` [Uboot-stm32] " Patrice CHOTARD
2020-06-04 12:30 ` [PATCH v2 02/11] board: stm32mp1: update the gpio hog support Patrick Delaunay
2020-07-02 7:42 ` [Uboot-stm32] " Patrice CHOTARD
2020-06-04 12:30 ` [PATCH v2 03/11] gpio: stm32: add ops set_dir_flags Patrick Delaunay
2020-07-02 7:48 ` Patrice CHOTARD
2020-06-04 12:30 ` [PATCH v2 04/11] gpio: stm32: add ops get_dir_flags Patrick Delaunay
2020-07-02 7:51 ` Patrice CHOTARD
2020-06-04 12:30 ` [PATCH v2 05/11] gpio: stmfx: move function to prepare new ops introduction Patrick Delaunay
2020-07-02 7:51 ` Patrice CHOTARD
2020-06-04 12:30 ` [PATCH v2 06/11] gpio: stmfx: rename function used to change pin configuration Patrick Delaunay
2020-07-02 7:51 ` Patrice CHOTARD
2020-06-04 12:30 ` [PATCH v2 07/11] gpio: stmfx: add function stmfx_read_reg and stmfx_write_reg Patrick Delaunay
2020-07-02 7:56 ` Patrice CHOTARD
2020-06-04 12:30 ` [PATCH v2 08/11] gpio: stmfx: add ops set_dir_flag Patrick Delaunay
2020-07-02 7:58 ` Patrice CHOTARD
2020-06-04 12:30 ` [PATCH v2 09/11] gpio: stmfx: add ops get_dir_flags Patrick Delaunay
2020-07-02 7:58 ` Patrice CHOTARD [this message]
2020-06-04 12:30 ` [PATCH v2 10/11] pinctrl: stmfx: add information on pin configuration Patrick Delaunay
2020-07-02 7:59 ` Patrice CHOTARD
2020-06-04 12:30 ` [PATCH v2 11/11] pinctrl: stm32: " Patrick Delaunay
2020-07-02 8:02 ` Patrice CHOTARD
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=7c313cec-1573-aa2b-20c6-eaa192bb721d@st.com \
--to=patrice.chotard@st.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox