[PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3

[Anand Moon <linux.amoon@gmail.com>]

Added support for vmmc/vqmmc-supply for emmc/sd cards.
Fixed the min values for regulator ldo13_reg (VDDQ_MMC2).
Added ramp-delay for LDO9(VDD33_USB3_0).
Added ramp-delay for LDO13(VDDQ_MMC2).
Added ramp-delay for LDO15(ETH_P3V3).

Signed-off-by: Anand Moon <linux.amoon@gmail.com>

---
Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch

Note:
Changes need for support of UHS-I highspeed cards.
changes for vqmmc-supply for emmc is not supported.

[    1.831136] vdd_ldo9: ramp_delay not set
[    1.843049] vdd_ldo13: ramp_delay not set
[    1.850975] vdd_ldo15: ramp_delay not set
[    1.862816] vdd_sd: ramp_delay not set
---
 arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
index 26decbd..58c06d3 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
@@ -157,6 +157,7 @@
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-always-on;
+				regulator-ramp-delay = <12000>;
 			};
 
 			ldo10_reg: LDO10 {
@@ -182,9 +183,10 @@
 
 			ldo13_reg: LDO13 {
 				regulator-name = "vdd_ldo13";
-				regulator-min-microvolt = <2800000>;
+				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <2800000>;
 				regulator-always-on;
+				regulator-ramp-delay = <12000>;
 			};
 
 			ldo15_reg: LDO15 {
@@ -213,6 +215,7 @@
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
 				regulator-always-on;
+				regulator-ramp-delay = <12000>;
 			};
 
 			ldo24_reg: LDO24 {
@@ -338,6 +341,7 @@
 	samsung,dw-mshc-ddr-timing = <0 2>;
 	samsung,dw-mshc-hs400-timing = <0 2>;
 	samsung,read-strobe-delay = <90>;
+	vmmc-supply = <&ldo3_reg>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>;
 	bus-width = <8>;
@@ -352,6 +356,8 @@
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <0 4>;
 	samsung,dw-mshc-ddr-timing = <0 2>;
+	vmmc-supply = <&ldo19_reg>;
+	vqmmc-supply = <&ldo13_reg>;
 	cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>;
 	cd-inverted;
 	pinctrl-names = "default";
-- 
2.1.4