Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support

[Krzysztof Kozlowski <k.kozlowski@samsung.com>]

W dniu 12.10.2015 o 19:46, Anand Moon pisze:
> Hi Krzysztof,
> 
> On 12 October 2015 at 11:14, Krzysztof Kozlowski
> <k.kozlowski@samsung.com> wrote:
>> On 12.10.2015 00:46, Anand Moon wrote:
>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104)
>>
>> This description is not entirely correct. The MMC driver already
>> supports these UHS speeds (you did not any code) so you rather enabled
>> it (description of bindings says "is supported").
>>
>> You mentioned DDR50 but I don't see respective property below.
> Looks like I missed it, I will add this in the next patch,
>>
>> How do you know that these modes are really supported? I don't know. Can
>> you convince me?

That part was not answered...

>>
> 
>>>
>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
>>>
>>> ---
>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch
>>>
>>> Changes Fixed the UHS-I bus speed detedtion on cold boot.
>>
>> I don't get what is exactly fixed here. What was the error? What is the
>> outcome of this fix? The log below is before or after?
>>
>> Best regards,
>> Krzysztof
>>
>>>
>>> [    2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
>>> [    2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa
>>> [    2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
>>> [    2.461743]  mmcblk0: p1 p2
>>
>>> ---
>>>  arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++
>>>  1 file changed, 4 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>>> index 58c06d3..ba4a87b 100644
>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>>> @@ -364,6 +364,10 @@
>>>       pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
>>>       bus-width = <4>;
>>>       cap-sd-highspeed;
>>> +     sd-uhs-sdr12;
>>> +     sd-uhs-sdr25;
>>> +     sd-uhs-sdr50;
>>> +     sd-uhs-sdr104;
>>>  };
>>>
>>>  &pinctrl_0 {
>>>
>>
> 
> Changes were made to support Sandisk Ultra UHS-I class 10 card support.
> OdroidXU3/XU4 board would not boot up using this card.
> 
> Depending on the capability of the UHS-I card, the speed of the card
> is selected.
> I have just added the enhance capability feature to support them.

So without these capabilities mentioned microSD card cannot be used? So
I have a UHS-I card, that one exactly:
http://www.samsung.com/us/support/owners/product/MB-MP32D/APC

It works:
[    2.628365] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req
50000000Hz, actual 50000000HZ div = 0)
[    2.693296] mmc1: new high speed SDHC card at address 0001
[    2.703867] mmcblk0: mmc1:0001 00000 29.8 GiB
[    2.708406]  mmcblk0: p1 p2

This is just HS mode.

In the same time isn't UHS-I backward compatible? Your report seems
surprising.

Best regards,
Krzysztof

> 
> On warm boot: i.e reboot of the board.
> [    4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot
> req 50000000Hz, actual 50000000HZ div = 0)
> [    4.657555] mmc1: new high speed SDHC card at address aaaa
> [    4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
> [    4.669206]  mmcblk0: p1 p2
> 
> On cold boot:: ie: power on the board.
> 
> [    4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot
> req 100000000Hz, actual 100000000HZ div = 0)
> [    4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa
> [    4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
> [    4.650293] IRQ56 no longer affine to CPU7
> [    4.650581] CPU7: shutdown
> [    4.658293]  mmcblk0: p1 p2
> 
> Note: Their is need to reset the PMIC
> S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers
>          to support this feature consistently on every reboot.
> 
> -Anand Moon
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
>