From: Jagan Teki <jagan@openedev.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 9/9] engicam: Generate single config file
Date: Fri, 12 May 2017 17:18:28 +0530 [thread overview]
Message-ID: <1494589708-15276-10-git-send-email-jagan@openedev.com> (raw)
In-Reply-To: <1494589708-15276-1-git-send-email-jagan@openedev.com>
From: Jagan Teki <jagan@amarulasolutions.com>
Engicam has several SOM's on i.MX6 stream, where each SOM
has one include/configs/*.h file, this patch generate single
config file for all SOM's include/configs/imx6-engicam.h
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/geam6ul/Kconfig | 2 +-
board/engicam/icorem6/Kconfig | 2 +-
board/engicam/icorem6_rqs/Kconfig | 2 +-
board/engicam/isiotmx6ul/Kconfig | 2 +-
.../configs/{imx6qdl_icore.h => imx6-engicam.h} | 39 ++--
include/configs/imx6qdl_icore_rqs.h | 149 ----------------
include/configs/imx6ul_geam.h | 197 --------------------
include/configs/imx6ul_isiot.h | 198 ---------------------
8 files changed, 33 insertions(+), 558 deletions(-)
rename include/configs/{imx6qdl_icore.h => imx6-engicam.h} (85%)
delete mode 100644 include/configs/imx6qdl_icore_rqs.h
delete mode 100644 include/configs/imx6ul_geam.h
delete mode 100644 include/configs/imx6ul_isiot.h
diff --git a/board/engicam/geam6ul/Kconfig b/board/engicam/geam6ul/Kconfig
index 8753d15..7f4023e 100644
--- a/board/engicam/geam6ul/Kconfig
+++ b/board/engicam/geam6ul/Kconfig
@@ -7,6 +7,6 @@ config SYS_VENDOR
default "engicam"
config SYS_CONFIG_NAME
- default "imx6ul_geam"
+ default "imx6-engicam"
endif
diff --git a/board/engicam/icorem6/Kconfig b/board/engicam/icorem6/Kconfig
index 6d62f0e..4a1c9ac 100644
--- a/board/engicam/icorem6/Kconfig
+++ b/board/engicam/icorem6/Kconfig
@@ -7,6 +7,6 @@ config SYS_VENDOR
default "engicam"
config SYS_CONFIG_NAME
- default "imx6qdl_icore"
+ default "imx6-engicam"
endif
diff --git a/board/engicam/icorem6_rqs/Kconfig b/board/engicam/icorem6_rqs/Kconfig
index 1352c68..6dc3a07 100644
--- a/board/engicam/icorem6_rqs/Kconfig
+++ b/board/engicam/icorem6_rqs/Kconfig
@@ -7,6 +7,6 @@ config SYS_VENDOR
default "engicam"
config SYS_CONFIG_NAME
- default "imx6qdl_icore_rqs"
+ default "imx6-engicam"
endif
diff --git a/board/engicam/isiotmx6ul/Kconfig b/board/engicam/isiotmx6ul/Kconfig
index 213ffad..10c2c50 100644
--- a/board/engicam/isiotmx6ul/Kconfig
+++ b/board/engicam/isiotmx6ul/Kconfig
@@ -7,6 +7,6 @@ config SYS_VENDOR
default "engicam"
config SYS_CONFIG_NAME
- default "imx6ul_isiot"
+ default "imx6-engicam"
endif
diff --git a/include/configs/imx6qdl_icore.h b/include/configs/imx6-engicam.h
similarity index 85%
rename from include/configs/imx6qdl_icore.h
rename to include/configs/imx6-engicam.h
index 4f7029d..e85dbc7 100644
--- a/include/configs/imx6qdl_icore.h
+++ b/include/configs/imx6-engicam.h
@@ -2,13 +2,13 @@
* Copyright (C) 2016 Amarula Solutions B.V.
* Copyright (C) 2016 Engicam S.r.l.
*
- * Configuration settings for the Engicam i.CoreM6 QDL Starter Kits.
+ * Configuration settings for the Engicam i.MX6 SOM Starter Kits.
*
* SPDX-License-Identifier: GPL-2.0+
*/
-#ifndef __IMX6QLD_ICORE_CONFIG_H
-#define __IMX6QLD_ICORE_CONFIG_H
+#ifndef __IMX6_ENGICAM_CONFIG_H
+#define __IMX6_ENGICAM_CONFIG_H
#include <linux/sizes.h>
#include "mx6_common.h"
@@ -109,8 +109,13 @@
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_HZ 1000
-#define DRAM_OFFSET(x) 0x1##x
-#define FDT_ADDR __stringify(DRAM_OFFSET(8000000))
+#ifdef CONFIG_MX6UL
+# define DRAM_OFFSET(x) 0x87##x
+# define FDT_ADDR __stringify(DRAM_OFFSET(800000))
+#else
+# define DRAM_OFFSET(x) 0x1##x
+# define FDT_ADDR __stringify(DRAM_OFFSET(8000000))
+#endif
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
@@ -135,7 +140,11 @@
/* UART */
#ifdef CONFIG_MXC_UART
-# define CONFIG_MXC_UART_BASE UART4_BASE
+# ifdef CONFIG_MX6UL
+# define CONFIG_MXC_UART_BASE UART1_BASE
+# else
+# define CONFIG_MXC_UART_BASE UART4_BASE
+# endif
#endif
/* MMC */
@@ -172,8 +181,13 @@
/* Ethernet */
#ifdef CONFIG_FEC_MXC
-# define CONFIG_FEC_MXC_PHYADDR 0
-# define CONFIG_FEC_XCV_TYPE RMII
+# ifdef CONFIG_TARGET_MX6Q_ICORE_RQS
+# define CONFIG_FEC_MXC_PHYADDR 3
+# define CONFIG_FEC_XCV_TYPE RGMII
+# else
+# define CONFIG_FEC_MXC_PHYADDR 0
+# define CONFIG_FEC_XCV_TYPE RMII
+# endif
# define CONFIG_MII
#endif
@@ -201,11 +215,16 @@
# include "imx6_spl.h"
# ifdef CONFIG_SPL_BUILD
-# define CONFIG_SYS_FSL_USDHC_NUM 1
+# if defined(CONFIG_TARGET_MX6Q_ICORE_RQS) || defined(CONFIG_TARGET_MX6UL_ISIOT)
+# define CONFIG_SYS_FSL_USDHC_NUM 2
+# else
+# define CONFIG_SYS_FSL_USDHC_NUM 1
+# endif
+
# define CONFIG_SYS_FSL_ESDHC_ADDR 0
# undef CONFIG_DM_GPIO
# undef CONFIG_DM_MMC
# endif
#endif
-#endif /* __IMX6QLD_ICORE_CONFIG_H */
+#endif /* __IMX6_ENGICAM_CONFIG_H */
diff --git a/include/configs/imx6qdl_icore_rqs.h b/include/configs/imx6qdl_icore_rqs.h
deleted file mode 100644
index d1e482d..0000000
--- a/include/configs/imx6qdl_icore_rqs.h
+++ /dev/null
@@ -1,149 +0,0 @@
-/*
- * Copyright (C) 2016 Amarula Solutions B.V.
- * Copyright (C) 2016 Engicam S.r.l.
- *
- * Configuration settings for the Engicam i.CoreM6 QDL RQS Starter Kits.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __IMX6QLD_ICORE_RQS_CONFIG_H
-#define __IMX6QLD_ICORE_RQS_CONFIG_H
-
-#include <linux/sizes.h>
-#include "mx6_common.h"
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
-
-/* Total Size of Environment Sector */
-#define CONFIG_ENV_SIZE SZ_128K
-
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Environment */
-#ifndef CONFIG_ENV_IS_NOWHERE
-/* Environment in MMC */
-# if defined(CONFIG_ENV_IS_IN_MMC)
-# define CONFIG_ENV_OFFSET 0x100000
-# endif
-#endif
-
-/* Default environment */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=boot.scr\0" \
- "image=uImage\0" \
- "fit_image=fit.itb\0" \
- "fdt_high=0xffffffff\0" \
- "fdt_addr=" FDT_ADDR "\0" \
- "boot_fdt=try\0" \
- "mmcpart=1\0" \
- "mmcautodetect=yes\0" \
- "mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}\0" \
- "loadbootscript=" \
- "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
- "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
- "loadfit=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${fit_image}\0" \
- "fitboot=echo Booting FIT image from mmc ...; " \
- "run mmcargs; " \
- "bootm ${loadaddr}\0" \
- "_mmcboot=run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootm; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootm; " \
- "fi\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "mmc dev ${mmcdev};" \
- "if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadfit; then " \
- "run fitboot; " \
- "else " \
- "if run loadimage; then " \
- "run _mmcboot; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi\0"
-
-#define CONFIG_BOOTCOMMAND "run $modeboot"
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_MEMTEST_START 0x80000000
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x8000000)
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_HZ 1000
-
-#define DRAM_OFFSET(x) 0x1##x
-#define FDT_ADDR __stringify(DRAM_OFFSET(8000000))
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_SP_OFFSET)
-
-/* FIT */
-#ifdef CONFIG_FIT
-# define CONFIG_HASH_VERIFY
-# define CONFIG_SHA1
-# define CONFIG_SHA256
-# define CONFIG_IMAGE_FORMAT_LEGACY
-#endif
-
-/* UART */
-#ifdef CONFIG_MXC_UART
-# define CONFIG_MXC_UART_BASE UART4_BASE
-#endif
-
-/* MMC */
-#ifdef CONFIG_FSL_USDHC
-# define CONFIG_SYS_MMC_ENV_DEV 0
-#endif
-
-/* Ethernet */
-#ifdef CONFIG_FEC_MXC
-# define CONFIG_FEC_MXC_PHYADDR 3
-# define CONFIG_FEC_XCV_TYPE RGMII
-
-# define CONFIG_MII
-#endif
-
-/* SPL */
-#ifdef CONFIG_SPL
-# define CONFIG_SPL_MMC_SUPPORT
-
-# include "imx6_spl.h"
-# ifdef CONFIG_SPL_BUILD
-# define CONFIG_SYS_FSL_USDHC_NUM 2
-# define CONFIG_SYS_FSL_ESDHC_ADDR 0
-# undef CONFIG_DM_GPIO
-# undef CONFIG_DM_MMC
-# endif
-#endif
-
-#endif /* __IMX6QLD_ICORE_RQS_CONFIG_H */
diff --git a/include/configs/imx6ul_geam.h b/include/configs/imx6ul_geam.h
deleted file mode 100644
index 0502e1b..0000000
--- a/include/configs/imx6ul_geam.h
+++ /dev/null
@@ -1,197 +0,0 @@
-/*
- * Copyright (C) 2016 Amarula Solutions B.V.
- * Copyright (C) 2016 Engicam S.r.l.
- *
- * Configuration settings for the Engicam GEAM6UL Starter Kits.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __IMX6UL_GEAM_CONFIG_H
-#define __IMX6UL_GEAM_CONFIG_H
-
-#include <linux/sizes.h>
-#include "mx6_common.h"
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
-
-/* Total Size of Environment Sector */
-#define CONFIG_ENV_SIZE SZ_128K
-
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Environment */
-#ifndef CONFIG_ENV_IS_NOWHERE
-/* Environment in MMC */
-# if defined(CONFIG_ENV_IS_IN_MMC)
-# define CONFIG_ENV_OFFSET 0x100000
-/* Environment in NAND */
-# elif defined(CONFIG_ENV_IS_IN_NAND)
-# define CONFIG_ENV_OFFSET 0x400000
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/* Default environment */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=boot.scr\0" \
- "image=uImage\0" \
- "fit_image=fit.itb\0" \
- "fdt_high=0xffffffff\0" \
- "fdt_addr=" FDT_ADDR "\0" \
- "boot_fdt=try\0" \
- "mmcpart=1\0" \
- "nandroot=ubi0:rootfs rootfstype=ubifs\0" \
- "mmcautodetect=yes\0" \
- "mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}\0" \
- "ubiargs=setenv bootargs console=${console},${baudrate} " \
- "ubi.mtd=5 root=${nandroot} ${mtdparts}\0" \
- "loadbootscript=" \
- "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
- "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
- "loadfit=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${fit_image}\0" \
- "fitboot=echo Booting FIT image from mmc ...; " \
- "run mmcargs; " \
- "bootm ${loadaddr}\0" \
- "_mmcboot=run mmcargs; " \
- "run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootm; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootm; " \
- "fi\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadfit; then " \
- "run fitboot; " \
- "else " \
- "if run loadimage; then " \
- "run _mmcboot; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi\0" \
- "nandboot=echo Booting from nand ...; " \
- "if mtdparts; then " \
- "echo Starting nand boot ...; " \
- "else " \
- "mtdparts default; " \
- "fi; " \
- "run ubiargs; " \
- "nand read ${loadaddr} kernel 0x800000; " \
- "nand read ${fdt_addr} dtb 0x100000; " \
- "bootm ${loadaddr} - ${fdt_addr}\0"
-
-#define CONFIG_BOOTCOMMAND "run $modeboot"
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_MEMTEST_START 0x80000000
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x8000000)
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_HZ 1000
-
-#define DRAM_OFFSET(x) 0x87##x
-#define FDT_ADDR __stringify(DRAM_OFFSET(800000))
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_SP_OFFSET)
-
-/* FIT */
-#ifdef CONFIG_FIT
-# define CONFIG_HASH_VERIFY
-# define CONFIG_SHA1
-# define CONFIG_SHA256
-# define CONFIG_IMAGE_FORMAT_LEGACY
-#endif
-
-/* UART */
-#ifdef CONFIG_MXC_UART
-# define CONFIG_MXC_UART_BASE UART1_BASE
-#endif
-
-/* MMC */
-#ifdef CONFIG_FSL_USDHC
-# define CONFIG_SYS_MMC_ENV_DEV 0
-#endif
-
-/* NAND */
-#ifdef CONFIG_NAND_MXS
-# define CONFIG_SYS_MAX_NAND_DEVICE 1
-# define CONFIG_SYS_NAND_BASE 0x40000000
-# define CONFIG_SYS_NAND_5_ADDR_CYCLE
-# define CONFIG_SYS_NAND_ONFI_DETECTION
-# define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-# define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
-
-/* MTD device */
-# define CONFIG_MTD_DEVICE
-# define CONFIG_CMD_MTDPARTS
-# define CONFIG_MTD_PARTITIONS
-# define MTDIDS_DEFAULT "nand0=gpmi-nand"
-# define MTDPARTS_DEFAULT "mtdparts=gpmi-nand:2m(spl),2m(uboot)," \
- "1m(env),8m(kernel),1m(dtb),-(rootfs)"
-
-/* UBI */
-# define CONFIG_CMD_UBIFS
-# define CONFIG_RBTREE
-# define CONFIG_LZO
-
-# define CONFIG_APBH_DMA
-# define CONFIG_APBH_DMA_BURST
-# define CONFIG_APBH_DMA_BURST8
-#endif
-
-/* Ethernet */
-#ifdef CONFIG_FEC_MXC
-# define CONFIG_FEC_MXC_PHYADDR 0
-# define CONFIG_FEC_XCV_TYPE RMII
-
-# define CONFIG_MII
-#endif
-
-/* SPL */
-#ifdef CONFIG_SPL
-# ifdef CONFIG_NAND_MXS
-# define CONFIG_SPL_NAND_SUPPORT
-# else
-# define CONFIG_SPL_MMC_SUPPORT
-# endif
-
-# include "imx6_spl.h"
-# ifdef CONFIG_SPL_BUILD
-# define CONFIG_SYS_FSL_USDHC_NUM 1
-# define CONFIG_SYS_FSL_ESDHC_ADDR 0
-# undef CONFIG_DM_GPIO
-# undef CONFIG_DM_MMC
-# endif
-#endif
-
-#endif /* __IMX6UL_GEAM_CONFIG_H */
diff --git a/include/configs/imx6ul_isiot.h b/include/configs/imx6ul_isiot.h
deleted file mode 100644
index 23aabed..0000000
--- a/include/configs/imx6ul_isiot.h
+++ /dev/null
@@ -1,198 +0,0 @@
-/*
- * Copyright (C) 2016 Amarula Solutions B.V.
- * Copyright (C) 2016 Engicam S.r.l.
- *
- * Configuration settings for the Engicam Is.IoT MX6UL Starter Kits.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __IMX6UL_ISIOT_CONFIG_H
-#define __IMX6UL_ISIOT_CONFIG_H
-
-#include <linux/sizes.h>
-#include "mx6_common.h"
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
-
-/* Total Size of Environment Sector */
-#define CONFIG_ENV_SIZE SZ_128K
-
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Environment */
-#ifndef CONFIG_ENV_IS_NOWHERE
-/* Environment in MMC */
-# if defined(CONFIG_ENV_IS_IN_MMC)
-# define CONFIG_ENV_OFFSET 0x100000
-/* Environment in NAND */
-# elif defined(CONFIG_ENV_IS_IN_NAND)
-# define CONFIG_ENV_OFFSET 0x400000
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/* Default environment */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=boot.scr\0" \
- "image=uImage\0" \
- "fit_image=fit.itb\0" \
- "splashpos=m,m\0" \
- "fdt_high=0xffffffff\0" \
- "fdt_addr=" FDT_ADDR "\0" \
- "boot_fdt=try\0" \
- "mmcpart=1\0" \
- "nandroot=ubi0:rootfs rootfstype=ubifs\0" \
- "mmcautodetect=yes\0" \
- "mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}\0" \
- "ubiargs=setenv bootargs console=${console},${baudrate} " \
- "ubi.mtd=5 root=${nandroot} ${mtdparts}\0" \
- "loadbootscript=" \
- "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
- "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
- "loadfit=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${fit_image}\0" \
- "fitboot=echo Booting FIT image from mmc ...; " \
- "run mmcargs; " \
- "bootm ${loadaddr}\0" \
- "_mmcboot=run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootm; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootm; " \
- "fi\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadfit; then " \
- "run fitboot; " \
- "else " \
- "if run loadimage; then " \
- "run _mmcboot; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi\0" \
- "nandboot=echo Booting from nand ...; " \
- "if mtdparts; then " \
- "echo Starting nand boot ...; " \
- "else " \
- "mtdparts default; " \
- "fi; " \
- "run ubiargs; " \
- "nand read ${loadaddr} kernel 0x800000; " \
- "nand read ${fdt_addr} dtb 0x100000; " \
- "bootm ${loadaddr} - ${fdt_addr}\0"
-
-#define CONFIG_BOOTCOMMAND "run $modeboot"
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_MEMTEST_START 0x80000000
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x8000000)
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_HZ 1000
-
-#define DRAM_OFFSET(x) 0x87##x
-#define FDT_ADDR __stringify(DRAM_OFFSET(800000))
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_SP_OFFSET)
-
-/* FIT */
-#ifdef CONFIG_FIT
-# define CONFIG_HASH_VERIFY
-# define CONFIG_SHA1
-# define CONFIG_SHA256
-# define CONFIG_IMAGE_FORMAT_LEGACY
-#endif
-
-/* UART */
-#ifdef CONFIG_MXC_UART
-# define CONFIG_MXC_UART_BASE UART1_BASE
-#endif
-
-/* MMC */
-#ifdef CONFIG_FSL_USDHC
-# define CONFIG_SYS_MMC_ENV_DEV 0
-#endif
-
-/* NAND */
-#ifdef CONFIG_NAND_MXS
-# define CONFIG_SYS_MAX_NAND_DEVICE 1
-# define CONFIG_SYS_NAND_BASE 0x40000000
-# define CONFIG_SYS_NAND_5_ADDR_CYCLE
-# define CONFIG_SYS_NAND_ONFI_DETECTION
-# define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-# define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
-
-/* MTD device */
-# define CONFIG_MTD_DEVICE
-# define CONFIG_CMD_MTDPARTS
-# define CONFIG_MTD_PARTITIONS
-# define MTDIDS_DEFAULT "nand0=gpmi-nand"
-# define MTDPARTS_DEFAULT "mtdparts=gpmi-nand:2m(spl),2m(uboot)," \
- "1m(env),8m(kernel),1m(dtb),-(rootfs)"
-
-/* UBI */
-# define CONFIG_CMD_UBIFS
-# define CONFIG_RBTREE
-# define CONFIG_LZO
-
-/* APBH DMA */
-# define CONFIG_APBH_DMA
-# define CONFIG_APBH_DMA_BURST
-# define CONFIG_APBH_DMA_BURST8
-#endif
-
-/* Ethernet */
-#ifdef CONFIG_FEC_MXC
-# define CONFIG_FEC_MXC_PHYADDR 0
-# define CONFIG_FEC_XCV_TYPE RMII
-
-# define CONFIG_MII
-#endif
-
-/* SPL */
-#ifdef CONFIG_SPL
-# ifdef CONFIG_NAND_MXS
-# define CONFIG_SPL_NAND_SUPPORT
-# else
-# define CONFIG_SPL_MMC_SUPPORT
-# endif
-
-# include "imx6_spl.h"
-# ifdef CONFIG_SPL_BUILD
-# define CONFIG_SYS_FSL_USDHC_NUM 2
-# define CONFIG_SYS_FSL_ESDHC_ADDR 0
-# undef CONFIG_DM_GPIO
-# undef CONFIG_DM_MMC
-# endif
-#endif
-
-#endif /* __IMX6UL_ISIOT_CONFIG_H */
--
1.9.1
next prev parent reply other threads:[~2017-05-12 11:48 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-05-12 11:48 [U-Boot] [PATCH 0/9] i.MX6: Engicam: Move common config code Jagan Teki
2017-05-12 11:48 ` [U-Boot] [PATCH 1/9] mmc: fsl_esdhc: Move non DM_MMC code in #ifndef CONFIG_DM_MMC Jagan Teki
2017-05-12 11:48 ` [U-Boot] [PATCH 2/9] engicam: Move SPL mmc configs under CONFIG_SPL_BUILD Jagan Teki
2017-05-12 11:48 ` [U-Boot] [PATCH 3/9] icorem6: Recover missing nand defconfig Jagan Teki
2017-05-12 11:48 ` [U-Boot] [PATCH 4/9] drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Jagan Teki
2017-05-12 11:48 ` [U-Boot] [PATCH 5/9] engicam: Move PHY configs to defconfig Jagan Teki
2017-05-12 11:48 ` [U-Boot] [PATCH 6/9] icorem6: Remove unused FEC configs Jagan Teki
2017-05-12 11:48 ` [U-Boot] [PATCH 7/9] engicam: Set console env on board_late_init Jagan Teki
2017-05-12 11:48 ` [U-Boot] [PATCH 8/9] engicam: Add fdt_addr env value based on cpu_type Jagan Teki
2017-05-12 11:48 ` Jagan Teki [this message]
2017-05-22 10:35 ` [U-Boot] [PATCH 0/9] i.MX6: Engicam: Move common config code Jagan Teki
2017-05-31 8:48 ` Stefano Babic
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1494589708-15276-10-git-send-email-jagan@openedev.com \
--to=jagan@openedev.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.