All of lore.kernel.org
 help / color / mirror / Atom feed
From: Jean Delvare <khali@linux-fr.org>
To: Oliver Pinter <oliver.pntr@gmail.com>
Cc: LM Sensors <lm-sensors@lm-sensors.org>, linux-kernel@vger.kernel.org
Subject: Re: [lm-sensors] Bad value with w83627thf
Date: Fri, 16 May 2008 13:27:12 +0000	[thread overview]
Message-ID: <20080516152712.629606bf@hyperion.delvare> (raw)
In-Reply-To: <6101e8c40805160559i4eb94ba7y7cbfea9c3f528821@mail.gmail.com>

Hi Oliver,

You are writing to the wrong mailing list (i2c instead of lm-sensors)
so I am redirecting.

On Fri, 16 May 2008 14:59:21 +0200, Oliver Pinter wrote:
> linux-2.6 - git HEAD on: 9662369
> lm-sensors: 1:3.0.1-5
> libsensors4: 1:3.0.1-5
> os: debian lenny
> sernsor: w83627thf on asus p4c800 MB
> 
> with 2.6.26-rcX kernel, reported false Battery values,
> -------------------------------------->
> VBat:        +3.26 V  (min =  +0.02 V, max =  +3.01 V)   ALARM
> <-------------------------------------

There is nothing wrong here. +3.26V sounds possible and correct for the
battery voltage. If you are worried about the min and max values: it is
up to you to edit your sensors3.conf file to set them properly if the
BIOS of your motherboard did not (apply the changes with "sensors -s").
The alarm will go away when you do.

> lspci -xxx
> 00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
> Controller (rev 02)
> 00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00
> 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

Completely irrelevant here, the Winbond W83627THF is an LPC chip, it
doesn't have an I2C/SMBus interface, so the SMBus controller doesn't
matter at all.

-- 
Jean Delvare

_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors

WARNING: multiple messages have this Message-ID (diff)
From: Jean Delvare <khali@linux-fr.org>
To: "Oliver Pinter" <oliver.pntr@gmail.com>
Cc: LM Sensors <lm-sensors@lm-sensors.org>, linux-kernel@vger.kernel.org
Subject: Re: Bad value with w83627thf
Date: Fri, 16 May 2008 15:27:12 +0200	[thread overview]
Message-ID: <20080516152712.629606bf@hyperion.delvare> (raw)
In-Reply-To: <6101e8c40805160559i4eb94ba7y7cbfea9c3f528821@mail.gmail.com>

Hi Oliver,

You are writing to the wrong mailing list (i2c instead of lm-sensors)
so I am redirecting.

On Fri, 16 May 2008 14:59:21 +0200, Oliver Pinter wrote:
> linux-2.6 - git HEAD on: 9662369
> lm-sensors: 1:3.0.1-5
> libsensors4: 1:3.0.1-5
> os: debian lenny
> sernsor: w83627thf on asus p4c800 MB
> 
> with 2.6.26-rcX kernel, reported false Battery values,
> -------------------------------------->
> VBat:        +3.26 V  (min =  +0.02 V, max =  +3.01 V)   ALARM
> <-------------------------------------

There is nothing wrong here. +3.26V sounds possible and correct for the
battery voltage. If you are worried about the min and max values: it is
up to you to edit your sensors3.conf file to set them properly if the
BIOS of your motherboard did not (apply the changes with "sensors -s").
The alarm will go away when you do.

> lspci -xxx
> 00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
> Controller (rev 02)
> 00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00
> 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

Completely irrelevant here, the Winbond W83627THF is an LPC chip, it
doesn't have an I2C/SMBus interface, so the SMBus controller doesn't
matter at all.

-- 
Jean Delvare

  reply	other threads:[~2008-05-16 13:27 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2008-05-16 12:59 Bad value with w83627thf Oliver Pinter
2008-05-16 12:59 ` Oliver Pinter
2008-05-16 13:27 ` Jean Delvare [this message]
2008-05-16 13:27   ` Jean Delvare
2008-05-16 13:45   ` [lm-sensors] " Oliver Pinter
2008-05-16 13:45     ` Oliver Pinter
2008-05-16 14:26     ` [lm-sensors] " Jean Delvare
2008-05-16 14:26       ` Jean Delvare
2008-05-16 14:34       ` [lm-sensors] " Oliver Pinter
2008-05-16 14:34         ` Oliver Pinter

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20080516152712.629606bf@hyperion.delvare \
    --to=khali@linux-fr.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=lm-sensors@lm-sensors.org \
    --cc=oliver.pntr@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.