From: Michael Bramer <michael@debsupport.de>
To: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: linux-kernel@vger.kernel.org, linux-serial@vger.kernel.org
Subject: Re: [PATCH] drivers/serial/8250_pci.c (add support for '8-port RS-232 MIC-3620 from advantech'
Date: Mon, 19 Jan 2009 11:45:26 +0000 [thread overview]
Message-ID: <20090119114526.GA1714@deb-support.de> (raw)
In-Reply-To: <20090118141409.3c2d0f95@lxorguk.ukuu.org.uk>
On Sun, Jan 18, 2009 at 02:14:09PM +0000, Alan Cox wrote:
> > + .vendor = PCI_VENDOR_ID_ADVANTECH,
> > + .device = PCI_DEVICE_ID_ADVANTECH_PCI3620,
> > + .subvendor = PCI_DEVICE_ID_ADVANTECH_PCI3620,
> > + .subdevice = PCI_ANY_ID,
>
> This looks odd - the subvendor ought to be a vendor id, and there should
> be a device id as well.
the number ist the same... i use now numbers in the patch...
> > can you add this in the next linux kernel?
>
> Can you firstly send me an lspci -vvxxx of that device. Also see
> Documentation/SubmittingPatches about Signed-off-by lines and we'll sort
> out merging it.
done:
eps:~# lspci -vvxxx -d 13fe:3620
04:0d.0 Serial controller: Advantech Co. Ltd Device 3620 (rev 01) (prog-if 00 [8250])
Subsystem: Device 3620:0001
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fddff000 (32-bit, non-prefetchable) [size=128]
Region 2: I/O ports at df00 [size=128]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] CompactPCI hot-swap <?>
Capabilities: [4c] Vital Product Data <?>
Kernel modules: 8250_pci-, 8250_pci
00: fe 13 20 36 03 00 90 02 01 00 00 07 10 00 00 00
10: 00 f0 df fd 00 00 00 00 01 df 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 20 36 01 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
40: 01 48 01 48 00 00 00 00 06 4c 00 00 03 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
and now the patch:
--------------
This Patch add the device information for the
MIC-3620 8-port RS-232 cPCI card from Advantech Co. Ltd.
Signed-off-by: Michael Bramer <grisu@deb-support.de>
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -31,6 +31,7 @@
#include "8250.h"
#undef SERIAL_DEBUG_PCI
+#define SERIAL_DEBUG_PCI
/*
* init function returns:
@@ -768,6 +769,8 @@
#define PCI_SUBDEVICE_ID_OCTPRO422 0x0208
#define PCI_SUBDEVICE_ID_POCTAL232 0x0308
#define PCI_SUBDEVICE_ID_POCTAL422 0x0408
+#define PCI_VENDOR_ID_ADVANTECH 0x13fe
+#define PCI_DEVICE_ID_ADVANTECH_PCI3620 0x3620
/*
* Master list of serial port init/setup/exit quirks.
@@ -789,6 +792,16 @@
.setup = addidata_apci7800_setup,
},
/*
+ * ADVANTECH
+ */
+ {
+ .vendor = PCI_VENDOR_ID_ADVANTECH,
+ .device = PCI_DEVICE_ID_ADVANTECH_PCI3620,
+ .subvendor = 0x3620,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_default_setup,
+ },
+ /*
* AFAVLAB cards - these may be called via parport_serial
* It is not clear whether this applies to all products.
*/
@@ -2041,6 +2054,9 @@
#endif
static struct pci_device_id serial_pci_tbl[] = {
+ { PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCI3620,
+ PCI_DEVICE_ID_ADVANTECH_PCI3620, PCI_ANY_ID, 0, 0,
+ pbn_b2_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
--------------
Thanks for your help
Gruss
Grisu
--
Michael Bramer -- http://www.feuerwehr.kreuzau.de/wiki/
PGP: finger grisu@db.debian.org -- Linux Sysadmin -- Use Debian Linux
"Wenn ich die Folgen geahnt hätte, wäre ich Uhrmacher geworden!"
--- Albert Einstein
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: Michael Bramer <michael@debsupport.de>
To: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: linux-kernel@vger.kernel.org, linux-serial@vger.kernel.org
Subject: Re: [PATCH] drivers/serial/8250_pci.c (add support for '8-port RS-232 MIC-3620 from advantech'
Date: Mon, 19 Jan 2009 11:45:26 +0000 [thread overview]
Message-ID: <20090119114526.GA1714@deb-support.de> (raw)
In-Reply-To: <20090118141409.3c2d0f95@lxorguk.ukuu.org.uk>
On Sun, Jan 18, 2009 at 02:14:09PM +0000, Alan Cox wrote:
> > + .vendor = PCI_VENDOR_ID_ADVANTECH,
> > + .device = PCI_DEVICE_ID_ADVANTECH_PCI3620,
> > + .subvendor = PCI_DEVICE_ID_ADVANTECH_PCI3620,
> > + .subdevice = PCI_ANY_ID,
>
> This looks odd - the subvendor ought to be a vendor id, and there should
> be a device id as well.
the number ist the same... i use now numbers in the patch...
> > can you add this in the next linux kernel?
>
> Can you firstly send me an lspci -vvxxx of that device. Also see
> Documentation/SubmittingPatches about Signed-off-by lines and we'll sort
> out merging it.
done:
eps:~# lspci -vvxxx -d 13fe:3620
04:0d.0 Serial controller: Advantech Co. Ltd Device 3620 (rev 01) (prog-if 00 [8250])
Subsystem: Device 3620:0001
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fddff000 (32-bit, non-prefetchable) [size=128]
Region 2: I/O ports at df00 [size=128]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] CompactPCI hot-swap <?>
Capabilities: [4c] Vital Product Data <?>
Kernel modules: 8250_pci-, 8250_pci
00: fe 13 20 36 03 00 90 02 01 00 00 07 10 00 00 00
10: 00 f0 df fd 00 00 00 00 01 df 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 20 36 01 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
40: 01 48 01 48 00 00 00 00 06 4c 00 00 03 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
and now the patch:
--------------
This Patch add the device information for the
MIC-3620 8-port RS-232 cPCI card from Advantech Co. Ltd.
Signed-off-by: Michael Bramer <grisu@deb-support.de>
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -31,6 +31,7 @@
#include "8250.h"
#undef SERIAL_DEBUG_PCI
+#define SERIAL_DEBUG_PCI
/*
* init function returns:
@@ -768,6 +769,8 @@
#define PCI_SUBDEVICE_ID_OCTPRO422 0x0208
#define PCI_SUBDEVICE_ID_POCTAL232 0x0308
#define PCI_SUBDEVICE_ID_POCTAL422 0x0408
+#define PCI_VENDOR_ID_ADVANTECH 0x13fe
+#define PCI_DEVICE_ID_ADVANTECH_PCI3620 0x3620
/*
* Master list of serial port init/setup/exit quirks.
@@ -789,6 +792,16 @@
.setup = addidata_apci7800_setup,
},
/*
+ * ADVANTECH
+ */
+ {
+ .vendor = PCI_VENDOR_ID_ADVANTECH,
+ .device = PCI_DEVICE_ID_ADVANTECH_PCI3620,
+ .subvendor = 0x3620,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_default_setup,
+ },
+ /*
* AFAVLAB cards - these may be called via parport_serial
* It is not clear whether this applies to all products.
*/
@@ -2041,6 +2054,9 @@
#endif
static struct pci_device_id serial_pci_tbl[] = {
+ { PCI_VENDOR_ID_ADVANTECH, PCI_DEVICE_ID_ADVANTECH_PCI3620,
+ PCI_DEVICE_ID_ADVANTECH_PCI3620, PCI_ANY_ID, 0, 0,
+ pbn_b2_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
--------------
Thanks for your help
Gruss
Grisu
--
Michael Bramer -- http://www.feuerwehr.kreuzau.de/wiki/
PGP: finger grisu@db.debian.org -- Linux Sysadmin -- Use Debian Linux
"Wenn ich die Folgen geahnt hätte, wäre ich Uhrmacher geworden!"
--- Albert Einstein
next prev parent reply other threads:[~2009-01-19 11:45 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-01-18 13:53 [PATCH] drivers/serial/8250_pci.c (add support for '8-port RS-232 MIC-3620 from advantech' Michael Bramer
2009-01-18 13:53 ` Michael Bramer
2009-01-18 14:14 ` Alan Cox
2009-01-19 11:45 ` Michael Bramer [this message]
2009-01-19 11:45 ` Michael Bramer
2009-01-19 14:51 ` Andrey Panin
2009-01-19 23:51 ` Michael Bramer
2009-01-19 23:51 ` Michael Bramer
2009-01-20 15:12 ` Andrey Panin
2009-01-21 7:52 ` Michael Bramer
2009-01-21 7:52 ` Michael Bramer
2009-01-21 8:18 ` Paulius Zaleckas
2009-01-21 8:40 ` Niels de Vos
2009-01-21 12:32 ` Alan Cox
2009-01-21 23:42 ` Michael Bramer
2009-01-21 23:42 ` Michael Bramer
2009-01-22 8:21 ` Tosoni
2009-01-22 8:21 ` Tosoni
2009-01-22 9:03 ` Niels de Vos
2009-01-22 11:00 ` Michael Bramer
2009-01-22 11:00 ` Michael Bramer
2009-01-22 11:47 ` Paulius Zaleckas
2009-01-22 16:44 ` Michael Bramer
2009-01-21 23:40 ` Michael Bramer
2009-01-21 23:40 ` Michael Bramer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20090119114526.GA1714@deb-support.de \
--to=michael@debsupport.de \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.