From: maxime.ripard@free-electrons.com (Maxime Ripard)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: dts: sun7i: Add Goodix GT911 nodes for Wexler TAB7200
Date: Tue, 31 Mar 2015 07:43:38 -0700 [thread overview]
Message-ID: <20150331144338.GG23664@lukather> (raw)
In-Reply-To: <1427789897-4085-1-git-send-email-mamlinav@gmail.com>
Hi,
On Tue, Mar 31, 2015 at 11:18:17AM +0300, Aleksei Mamlin wrote:
> This patch adds nodes for the Goodix GT911 touchscreen controller found
> on the Wexler TAB7200 tablet. Controller uses one of following I2C
> addresses: 0x5d or 0x14, so just add two nodes.
In which case are these different addresses encountered? Different
revisions of the same board?
> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
> ---
> DT support for the Goodix GT911 touchscreen controller has been queued up
> by Dmitry Torokhov for merging into 4.1:
> https://git.kernel.org/cgit/linux/kernel/git/dtor/input.git/commit/?h=next&id=771d8f1b178e7e09fcc641fccd48852958dbc329
>
> IRQ flags are set by the touchscreen controller driver, so use IRQ_TYPE_NONE.
>
> arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 14 ++++++++++++++
> 1 file changed, 14 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> index 2ad3b09..34e2bce 100644
> --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> @@ -101,6 +101,20 @@
> pinctrl-names = "default";
> pinctrl-0 = <&i2c2_pins_a>;
> status = "okay";
> +
> + gt911 at 5d {
The node name should be the class of the device. touchscreen in this
case.
> + compatible = "goodix,gt911";
> + reg = <0x5d>;
> + interrupt-parent = <&pio>;
> + interrupts = <21 IRQ_TYPE_NONE>; /* EINT21 (PH21) */
Unfortunately, IRQ_TYPE_NONE is not a valid value for the GIC
bindings.
You're also not adding a pinctrl group for that pin?
> + };
> +
> + gt911 at 14 {
> + compatible = "goodix,gt911";
> + reg = <0x14>;
> + interrupt-parent = <&pio>;
> + interrupts = <21 IRQ_TYPE_NONE>; /* EINT21 (PH21) */
> + };
And nodes should be ordered by addresses ascending order.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150331/a6c2adac/attachment.sig>
WARNING: multiple messages have this Message-ID (diff)
From: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
To: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Subject: Re: [PATCH] ARM: dts: sun7i: Add Goodix GT911 nodes for Wexler TAB7200
Date: Tue, 31 Mar 2015 07:43:38 -0700 [thread overview]
Message-ID: <20150331144338.GG23664@lukather> (raw)
In-Reply-To: <1427789897-4085-1-git-send-email-mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
[-- Attachment #1: Type: text/plain, Size: 2033 bytes --]
Hi,
On Tue, Mar 31, 2015 at 11:18:17AM +0300, Aleksei Mamlin wrote:
> This patch adds nodes for the Goodix GT911 touchscreen controller found
> on the Wexler TAB7200 tablet. Controller uses one of following I2C
> addresses: 0x5d or 0x14, so just add two nodes.
In which case are these different addresses encountered? Different
revisions of the same board?
> Signed-off-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> DT support for the Goodix GT911 touchscreen controller has been queued up
> by Dmitry Torokhov for merging into 4.1:
> https://git.kernel.org/cgit/linux/kernel/git/dtor/input.git/commit/?h=next&id=771d8f1b178e7e09fcc641fccd48852958dbc329
>
> IRQ flags are set by the touchscreen controller driver, so use IRQ_TYPE_NONE.
>
> arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 14 ++++++++++++++
> 1 file changed, 14 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> index 2ad3b09..34e2bce 100644
> --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
> @@ -101,6 +101,20 @@
> pinctrl-names = "default";
> pinctrl-0 = <&i2c2_pins_a>;
> status = "okay";
> +
> + gt911@5d {
The node name should be the class of the device. touchscreen in this
case.
> + compatible = "goodix,gt911";
> + reg = <0x5d>;
> + interrupt-parent = <&pio>;
> + interrupts = <21 IRQ_TYPE_NONE>; /* EINT21 (PH21) */
Unfortunately, IRQ_TYPE_NONE is not a valid value for the GIC
bindings.
You're also not adding a pinctrl group for that pin?
> + };
> +
> + gt911@14 {
> + compatible = "goodix,gt911";
> + reg = <0x14>;
> + interrupt-parent = <&pio>;
> + interrupts = <21 IRQ_TYPE_NONE>; /* EINT21 (PH21) */
> + };
And nodes should be ordered by addresses ascending order.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
next prev parent reply other threads:[~2015-03-31 14:43 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-03-31 8:18 [PATCH] ARM: dts: sun7i: Add Goodix GT911 nodes for Wexler TAB7200 Aleksei Mamlin
2015-03-31 8:18 ` Aleksei Mamlin
2015-03-31 14:43 ` Maxime Ripard [this message]
2015-03-31 14:43 ` Maxime Ripard
2015-03-31 19:14 ` Aleksei Mamlin
2015-03-31 19:14 ` Aleksei Mamlin
2015-04-02 9:22 ` Maxime Ripard
2015-04-02 9:22 ` Maxime Ripard
2015-04-11 16:18 ` Aleksei Mamlin
2015-04-11 16:18 ` Aleksei Mamlin
2015-04-13 16:09 ` Maxime Ripard
2015-04-13 16:09 ` Maxime Ripard
2015-04-13 19:01 ` Aleksei Mamlin
2015-04-13 19:01 ` Aleksei Mamlin
2015-04-14 16:32 ` Maxime Ripard
2015-04-14 16:32 ` Maxime Ripard
2015-03-31 19:31 ` Aleksei Mamlin
2015-03-31 19:31 ` Aleksei Mamlin
2015-04-02 18:50 ` Maxime Ripard
2015-04-02 18:50 ` Maxime Ripard
2015-04-11 16:36 ` Aleksei Mamlin
2015-04-11 16:36 ` Aleksei Mamlin
2015-04-13 15:59 ` Maxime Ripard
2015-04-13 15:59 ` Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150331144338.GG23664@lukather \
--to=maxime.ripard@free-electrons.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.