From: Robin Gong <b38343@freescale.com>
To: Anton Bondarenko <anton_bondarenko@mentor.com>
Cc: <broonie@kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-spi@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>, <jiada_wang@mentor.com>,
<muzaffar_mahmood@relay1.mentorg.com>,
<vladimir_zapolskiy@mentor.com>
Subject: Re: [PATCH v2 3/8] spi: imx: add support for all SPI word width for DMA transfer
Date: Wed, 30 Sep 2015 16:35:40 +0800 [thread overview]
Message-ID: <20150930083539.GD2709@shlinux2> (raw)
In-Reply-To: <f8844a7a52ab44f00e7b6a1c3ce55d72d7999514.1442923630.git.anton_bondarenko@mentor.com>
On Fri, Sep 25, 2015 at 07:57:10PM +0200, Anton Bondarenko wrote:
> DMA transfer for SPI was limited to up to 8 bits word size until now.
> Sync in SPI burst size and DMA bus width is necessary to correctly
> support other BPW supported by HW.
>
> Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
> ---
> drivers/spi/spi-imx.c | 121 ++++++++++++++++++++++++++++++++++++--------------
> 1 file changed, 87 insertions(+), 34 deletions(-)
>
> diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
> index 6c98eda..d9b730d 100644
> --- a/drivers/spi/spi-imx.c
> +++ b/drivers/spi/spi-imx.c
> @@ -91,11 +91,15 @@ struct spi_imx_data {
>
> struct completion xfer_done;
> void __iomem *base;
> + unsigned long base_phys;
> +
> struct clk *clk_per;
> struct clk *clk_ipg;
> unsigned long spi_clk;
> unsigned int spi_bus_clk;
>
> + unsigned int bpw_w;
> +
It's better to change bytes_per_word for clear understanding,since bpw in spi means
bits_per_word...
> unsigned int count;
> void (*tx)(struct spi_imx_data *);
> void (*rx)(struct spi_imx_data *);
> @@ -201,9 +205,13 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi,
> struct spi_transfer *transfer)
> {
> struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
> + unsigned int bpw_w = transfer->bits_per_word;
>
> - if (spi_imx->dma_is_inited &&
> - (transfer->len > spi_imx->wml * sizeof(u32)))
> + if (!bpw_w)
> + bpw_w = spi->bits_per_word;
> +
> + bpw_w = DIV_ROUND_UP(bpw_w, 8);
> + if (spi_imx->dma_is_inited && (transfer->len > spi_imx->wml * bpw_w))
Please remove bpw_w here as I talked in the first patch.
> return true;
> return false;
> }
> @@ -761,11 +769,62 @@ static irqreturn_t spi_imx_isr(int irq, void *dev_id)
> return IRQ_HANDLED;
> }
>
> +static int spi_imx_sdma_configure(struct spi_master *master)
> +{
> + int ret;
> + enum dma_slave_buswidth dsb_default = DMA_SLAVE_BUSWIDTH_1_BYTE;
> + struct dma_slave_config slave_config = {};
> + struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
> +
> + switch (spi_imx->bpw_w) {
> + case 4:
> + dsb_default = DMA_SLAVE_BUSWIDTH_4_BYTES;
> + break;
> + case 2:
> + dsb_default = DMA_SLAVE_BUSWIDTH_2_BYTES;
> + break;
> + case 1:
> + dsb_default = DMA_SLAVE_BUSWIDTH_1_BYTE;
> + break;
> + default:
> + pr_err("Not supported word size %d\n", spi_imx->bpw_w);
> + ret = -EINVAL;
> + goto err;
> + }
> +
> + slave_config.direction = DMA_MEM_TO_DEV;
> + slave_config.dst_addr = spi_imx->base_phys + MXC_CSPITXDATA;
> + slave_config.dst_addr_width = dsb_default;
> + slave_config.dst_maxburst = spi_imx_get_fifosize(spi_imx)
> + - spi_imx->wml;
> + ret = dmaengine_slave_config(master->dma_tx, &slave_config);
> + if (ret) {
> + pr_err("error in TX dma configuration.\n");
> + goto err;
> + }
> +
> + memset(&slave_config, 0, sizeof(slave_config));
> +
> + slave_config.direction = DMA_DEV_TO_MEM;
> + slave_config.src_addr = spi_imx->base_phys + MXC_CSPIRXDATA;
> + slave_config.src_addr_width = dsb_default;
> + slave_config.src_maxburst = spi_imx_get_fifosize(spi_imx)
> + - spi_imx->wml;
> + ret = dmaengine_slave_config(master->dma_rx, &slave_config);
> + if (ret)
> + pr_err("error in RX dma configuration.\n");
> +
> +err:
> + return ret;
> +}
> +
> static int spi_imx_setupxfer(struct spi_device *spi,
> struct spi_transfer *t)
> {
> struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
> struct spi_imx_config config;
> + unsigned int bpw_w_new;
> + int ret = 0;
>
> config.bpw = t ? t->bits_per_word : spi->bits_per_word;
> config.speed_hz = t ? t->speed_hz : spi->max_speed_hz;
> @@ -789,9 +848,18 @@ static int spi_imx_setupxfer(struct spi_device *spi,
> spi_imx->tx = spi_imx_buf_tx_u32;
> }
>
> - spi_imx->devtype_data->config(spi_imx, &config);
> + bpw_w_new = DIV_ROUND_UP(config.bpw, 8);
> + if (spi_imx->dma_is_inited && spi_imx->bpw_w != bpw_w_new) {
> + spi_imx->bpw_w = bpw_w_new;
> + ret = spi_imx_sdma_configure(spi->master);
> + if (ret != 0)
> + pr_err("Can't configure SDMA, error %d\n", ret);
> + }
>
> - return 0;
> + if (!ret)
> + ret = spi_imx->devtype_data->config(spi_imx, &config);
> +
> + return ret;
> }
>
> static void spi_imx_sdma_exit(struct spi_imx_data *spi_imx)
> @@ -812,10 +880,8 @@ static void spi_imx_sdma_exit(struct spi_imx_data *spi_imx)
> }
>
> static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
> - struct spi_master *master,
> - const struct resource *res)
> + struct spi_master *master)
> {
> - struct dma_slave_config slave_config = {};
> int ret;
>
> /* use pio mode for i.mx6dl chip TKT238285 */
> @@ -832,17 +898,6 @@ static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
> goto err;
> }
>
> - slave_config.direction = DMA_MEM_TO_DEV;
> - slave_config.dst_addr = res->start + MXC_CSPITXDATA;
> - slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> - slave_config.dst_maxburst = spi_imx_get_fifosize(spi_imx)
> - - spi_imx->wml;
> - ret = dmaengine_slave_config(master->dma_tx, &slave_config);
> - if (ret) {
> - dev_err(dev, "error in TX dma configuration.\n");
> - goto err;
> - }
> -
> /* Prepare for RX : */
> master->dma_rx = dma_request_slave_channel(dev, "rx");
> if (!master->dma_rx) {
> @@ -851,23 +906,19 @@ static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
> goto err;
> }
>
> - slave_config.direction = DMA_DEV_TO_MEM;
> - slave_config.src_addr = res->start + MXC_CSPIRXDATA;
> - slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> - slave_config.src_maxburst = spi_imx_get_fifosize(spi_imx)
> - - spi_imx->wml;
> - ret = dmaengine_slave_config(master->dma_rx, &slave_config);
> - if (ret) {
> - dev_err(dev, "error in RX dma configuration.\n");
> - goto err;
> - }
> -
> init_completion(&spi_imx->dma_rx_completion);
> init_completion(&spi_imx->dma_tx_completion);
> master->can_dma = spi_imx_can_dma;
> master->max_dma_len = MAX_SDMA_BD_BYTES;
> spi_imx->bitbang.master->flags = SPI_MASTER_MUST_RX |
> SPI_MASTER_MUST_TX;
> + spi_imx->bpw_w = 1;
> + ret = spi_imx_sdma_configure(master);
> + if (ret) {
> + dev_info(dev, "cannot get setup DMA.\n");
> + goto err;
> + }
> +
> spi_imx->dma_is_inited = 1;
>
> return 0;
> @@ -924,7 +975,7 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
> int ret;
> unsigned long timeout;
> unsigned long transfer_timeout;
> - const int left = transfer->len % spi_imx->wml;
> + const int left = transfer->len % (spi_imx->wml * spi_imx->bpw_w);
> struct spi_master *master = spi_imx->bitbang.master;
> struct sg_table *tx = &transfer->tx_sg, *rx = &transfer->rx_sg;
>
> @@ -989,7 +1040,7 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
> dmaengine_terminate_all(master->dma_rx);
> } else {
> transfer_timeout = spi_imx_calculate_timeout(spi_imx,
> - spi_imx->wml * 2);
> + spi_imx->bpw_w * spi_imx->wml * 2);
> timeout = wait_for_completion_timeout(
> &spi_imx->dma_rx_completion, transfer_timeout);
> if (!timeout) {
> @@ -1007,7 +1058,8 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
> DMA_FROM_DEVICE);
>
> spi_imx->rx_buf = pio_buffer;
> - spi_imx->txfifo = left;
> + spi_imx->txfifo = DIV_ROUND_UP(left, spi_imx->bpw_w);
> +
Looks not enough here, you have to set 'spi_imx->rx' per the right bpw.
> reinit_completion(&spi_imx->xfer_done);
>
> spi_imx->devtype_data->intctrl(spi_imx, MXC_INT_TCEN);
> @@ -1207,6 +1259,7 @@ static int spi_imx_probe(struct platform_device *pdev)
> ret = PTR_ERR(spi_imx->base);
> goto out_master_put;
> }
> + spi_imx->base_phys = res->start;
>
> irq = platform_get_irq(pdev, 0);
> if (irq < 0) {
> @@ -1246,8 +1299,8 @@ static int spi_imx_probe(struct platform_device *pdev)
> * Only validated on i.mx6 now, can remove the constrain if validated on
> * other chips.
> */
> - if (spi_imx->devtype_data == &imx51_ecspi_devtype_data
> - && spi_imx_sdma_init(&pdev->dev, spi_imx, master, res))
> + if (spi_imx->devtype_data == &imx51_ecspi_devtype_data &&
> + spi_imx_sdma_init(&pdev->dev, spi_imx, master))
> dev_err(&pdev->dev, "dma setup error,use pio instead\n");
>
> spi_imx->devtype_data->reset(spi_imx);
> --
> 2.5.2
>
WARNING: multiple messages have this Message-ID (diff)
From: b38343@freescale.com (Robin Gong)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 3/8] spi: imx: add support for all SPI word width for DMA transfer
Date: Wed, 30 Sep 2015 16:35:40 +0800 [thread overview]
Message-ID: <20150930083539.GD2709@shlinux2> (raw)
In-Reply-To: <f8844a7a52ab44f00e7b6a1c3ce55d72d7999514.1442923630.git.anton_bondarenko@mentor.com>
On Fri, Sep 25, 2015 at 07:57:10PM +0200, Anton Bondarenko wrote:
> DMA transfer for SPI was limited to up to 8 bits word size until now.
> Sync in SPI burst size and DMA bus width is necessary to correctly
> support other BPW supported by HW.
>
> Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
> ---
> drivers/spi/spi-imx.c | 121 ++++++++++++++++++++++++++++++++++++--------------
> 1 file changed, 87 insertions(+), 34 deletions(-)
>
> diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
> index 6c98eda..d9b730d 100644
> --- a/drivers/spi/spi-imx.c
> +++ b/drivers/spi/spi-imx.c
> @@ -91,11 +91,15 @@ struct spi_imx_data {
>
> struct completion xfer_done;
> void __iomem *base;
> + unsigned long base_phys;
> +
> struct clk *clk_per;
> struct clk *clk_ipg;
> unsigned long spi_clk;
> unsigned int spi_bus_clk;
>
> + unsigned int bpw_w;
> +
It's better to change bytes_per_word for clear understanding,since bpw in spi means
bits_per_word...
> unsigned int count;
> void (*tx)(struct spi_imx_data *);
> void (*rx)(struct spi_imx_data *);
> @@ -201,9 +205,13 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi,
> struct spi_transfer *transfer)
> {
> struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
> + unsigned int bpw_w = transfer->bits_per_word;
>
> - if (spi_imx->dma_is_inited &&
> - (transfer->len > spi_imx->wml * sizeof(u32)))
> + if (!bpw_w)
> + bpw_w = spi->bits_per_word;
> +
> + bpw_w = DIV_ROUND_UP(bpw_w, 8);
> + if (spi_imx->dma_is_inited && (transfer->len > spi_imx->wml * bpw_w))
Please remove bpw_w here as I talked in the first patch.
> return true;
> return false;
> }
> @@ -761,11 +769,62 @@ static irqreturn_t spi_imx_isr(int irq, void *dev_id)
> return IRQ_HANDLED;
> }
>
> +static int spi_imx_sdma_configure(struct spi_master *master)
> +{
> + int ret;
> + enum dma_slave_buswidth dsb_default = DMA_SLAVE_BUSWIDTH_1_BYTE;
> + struct dma_slave_config slave_config = {};
> + struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
> +
> + switch (spi_imx->bpw_w) {
> + case 4:
> + dsb_default = DMA_SLAVE_BUSWIDTH_4_BYTES;
> + break;
> + case 2:
> + dsb_default = DMA_SLAVE_BUSWIDTH_2_BYTES;
> + break;
> + case 1:
> + dsb_default = DMA_SLAVE_BUSWIDTH_1_BYTE;
> + break;
> + default:
> + pr_err("Not supported word size %d\n", spi_imx->bpw_w);
> + ret = -EINVAL;
> + goto err;
> + }
> +
> + slave_config.direction = DMA_MEM_TO_DEV;
> + slave_config.dst_addr = spi_imx->base_phys + MXC_CSPITXDATA;
> + slave_config.dst_addr_width = dsb_default;
> + slave_config.dst_maxburst = spi_imx_get_fifosize(spi_imx)
> + - spi_imx->wml;
> + ret = dmaengine_slave_config(master->dma_tx, &slave_config);
> + if (ret) {
> + pr_err("error in TX dma configuration.\n");
> + goto err;
> + }
> +
> + memset(&slave_config, 0, sizeof(slave_config));
> +
> + slave_config.direction = DMA_DEV_TO_MEM;
> + slave_config.src_addr = spi_imx->base_phys + MXC_CSPIRXDATA;
> + slave_config.src_addr_width = dsb_default;
> + slave_config.src_maxburst = spi_imx_get_fifosize(spi_imx)
> + - spi_imx->wml;
> + ret = dmaengine_slave_config(master->dma_rx, &slave_config);
> + if (ret)
> + pr_err("error in RX dma configuration.\n");
> +
> +err:
> + return ret;
> +}
> +
> static int spi_imx_setupxfer(struct spi_device *spi,
> struct spi_transfer *t)
> {
> struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
> struct spi_imx_config config;
> + unsigned int bpw_w_new;
> + int ret = 0;
>
> config.bpw = t ? t->bits_per_word : spi->bits_per_word;
> config.speed_hz = t ? t->speed_hz : spi->max_speed_hz;
> @@ -789,9 +848,18 @@ static int spi_imx_setupxfer(struct spi_device *spi,
> spi_imx->tx = spi_imx_buf_tx_u32;
> }
>
> - spi_imx->devtype_data->config(spi_imx, &config);
> + bpw_w_new = DIV_ROUND_UP(config.bpw, 8);
> + if (spi_imx->dma_is_inited && spi_imx->bpw_w != bpw_w_new) {
> + spi_imx->bpw_w = bpw_w_new;
> + ret = spi_imx_sdma_configure(spi->master);
> + if (ret != 0)
> + pr_err("Can't configure SDMA, error %d\n", ret);
> + }
>
> - return 0;
> + if (!ret)
> + ret = spi_imx->devtype_data->config(spi_imx, &config);
> +
> + return ret;
> }
>
> static void spi_imx_sdma_exit(struct spi_imx_data *spi_imx)
> @@ -812,10 +880,8 @@ static void spi_imx_sdma_exit(struct spi_imx_data *spi_imx)
> }
>
> static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
> - struct spi_master *master,
> - const struct resource *res)
> + struct spi_master *master)
> {
> - struct dma_slave_config slave_config = {};
> int ret;
>
> /* use pio mode for i.mx6dl chip TKT238285 */
> @@ -832,17 +898,6 @@ static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
> goto err;
> }
>
> - slave_config.direction = DMA_MEM_TO_DEV;
> - slave_config.dst_addr = res->start + MXC_CSPITXDATA;
> - slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> - slave_config.dst_maxburst = spi_imx_get_fifosize(spi_imx)
> - - spi_imx->wml;
> - ret = dmaengine_slave_config(master->dma_tx, &slave_config);
> - if (ret) {
> - dev_err(dev, "error in TX dma configuration.\n");
> - goto err;
> - }
> -
> /* Prepare for RX : */
> master->dma_rx = dma_request_slave_channel(dev, "rx");
> if (!master->dma_rx) {
> @@ -851,23 +906,19 @@ static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
> goto err;
> }
>
> - slave_config.direction = DMA_DEV_TO_MEM;
> - slave_config.src_addr = res->start + MXC_CSPIRXDATA;
> - slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> - slave_config.src_maxburst = spi_imx_get_fifosize(spi_imx)
> - - spi_imx->wml;
> - ret = dmaengine_slave_config(master->dma_rx, &slave_config);
> - if (ret) {
> - dev_err(dev, "error in RX dma configuration.\n");
> - goto err;
> - }
> -
> init_completion(&spi_imx->dma_rx_completion);
> init_completion(&spi_imx->dma_tx_completion);
> master->can_dma = spi_imx_can_dma;
> master->max_dma_len = MAX_SDMA_BD_BYTES;
> spi_imx->bitbang.master->flags = SPI_MASTER_MUST_RX |
> SPI_MASTER_MUST_TX;
> + spi_imx->bpw_w = 1;
> + ret = spi_imx_sdma_configure(master);
> + if (ret) {
> + dev_info(dev, "cannot get setup DMA.\n");
> + goto err;
> + }
> +
> spi_imx->dma_is_inited = 1;
>
> return 0;
> @@ -924,7 +975,7 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
> int ret;
> unsigned long timeout;
> unsigned long transfer_timeout;
> - const int left = transfer->len % spi_imx->wml;
> + const int left = transfer->len % (spi_imx->wml * spi_imx->bpw_w);
> struct spi_master *master = spi_imx->bitbang.master;
> struct sg_table *tx = &transfer->tx_sg, *rx = &transfer->rx_sg;
>
> @@ -989,7 +1040,7 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
> dmaengine_terminate_all(master->dma_rx);
> } else {
> transfer_timeout = spi_imx_calculate_timeout(spi_imx,
> - spi_imx->wml * 2);
> + spi_imx->bpw_w * spi_imx->wml * 2);
> timeout = wait_for_completion_timeout(
> &spi_imx->dma_rx_completion, transfer_timeout);
> if (!timeout) {
> @@ -1007,7 +1058,8 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
> DMA_FROM_DEVICE);
>
> spi_imx->rx_buf = pio_buffer;
> - spi_imx->txfifo = left;
> + spi_imx->txfifo = DIV_ROUND_UP(left, spi_imx->bpw_w);
> +
Looks not enough here, you have to set 'spi_imx->rx' per the right bpw.
> reinit_completion(&spi_imx->xfer_done);
>
> spi_imx->devtype_data->intctrl(spi_imx, MXC_INT_TCEN);
> @@ -1207,6 +1259,7 @@ static int spi_imx_probe(struct platform_device *pdev)
> ret = PTR_ERR(spi_imx->base);
> goto out_master_put;
> }
> + spi_imx->base_phys = res->start;
>
> irq = platform_get_irq(pdev, 0);
> if (irq < 0) {
> @@ -1246,8 +1299,8 @@ static int spi_imx_probe(struct platform_device *pdev)
> * Only validated on i.mx6 now, can remove the constrain if validated on
> * other chips.
> */
> - if (spi_imx->devtype_data == &imx51_ecspi_devtype_data
> - && spi_imx_sdma_init(&pdev->dev, spi_imx, master, res))
> + if (spi_imx->devtype_data == &imx51_ecspi_devtype_data &&
> + spi_imx_sdma_init(&pdev->dev, spi_imx, master))
> dev_err(&pdev->dev, "dma setup error,use pio instead\n");
>
> spi_imx->devtype_data->reset(spi_imx);
> --
> 2.5.2
>
next prev parent reply other threads:[~2015-09-30 8:35 UTC|newest]
Thread overview: 52+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-25 17:57 [PATCH v2 0/8] Improvements for SPI IMX driver for Freescale IMX53 and IMX6 families Anton Bondarenko
2015-09-25 17:57 ` Anton Bondarenko
2015-09-25 17:57 ` [PATCH v2 1/8] spi: imx: Fix DMA transfer Anton Bondarenko
2015-09-25 17:57 ` Anton Bondarenko
2015-09-28 3:48 ` kbuild test robot
2015-09-28 3:48 ` kbuild test robot
[not found] ` <d61ed8cc9e13b0890e6243135c613edea1234698.1442923630.git.anton_bondarenko-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
2015-09-30 8:23 ` Robin Gong
2015-09-30 8:23 ` Robin Gong
2015-10-01 0:02 ` Bondarenko, Anton
2015-10-01 0:02 ` Bondarenko, Anton
2015-10-08 9:19 ` Robin Gong
2015-10-08 9:19 ` Robin Gong
2015-10-20 23:03 ` Anton Bondarenko
2015-10-20 23:03 ` Anton Bondarenko
2015-09-25 17:57 ` [PATCH v2 2/8] spi: imx: replace fixed timeout with calculated one Anton Bondarenko
2015-09-25 17:57 ` Anton Bondarenko
2015-09-30 8:31 ` Robin Gong
2015-09-30 8:31 ` Robin Gong
2015-10-01 0:08 ` Bondarenko, Anton
2015-10-01 0:08 ` Bondarenko, Anton
2015-09-25 17:57 ` [PATCH v2 3/8] spi: imx: add support for all SPI word width for DMA transfer Anton Bondarenko
2015-09-25 17:57 ` Anton Bondarenko
2015-09-30 8:35 ` Robin Gong [this message]
2015-09-30 8:35 ` Robin Gong
2015-10-01 0:34 ` Bondarenko, Anton
2015-10-01 0:34 ` Bondarenko, Anton
2015-10-08 9:51 ` Robin Gong
2015-10-08 9:51 ` Robin Gong
2015-10-20 23:28 ` Anton Bondarenko
2015-10-20 23:28 ` Anton Bondarenko
2015-09-25 17:57 ` [PATCH v2 4/8] spi: imx: add selection for iMX53 and iMX6 controller type Anton Bondarenko
2015-09-25 17:57 ` Anton Bondarenko
2015-09-25 17:57 ` [PATCH v2 5/8] spi: imx: Add support for loopback for ECSPI controllers Anton Bondarenko
2015-09-25 17:57 ` Anton Bondarenko
2015-09-30 8:42 ` Robin Gong
2015-09-30 8:42 ` Robin Gong
2015-10-01 0:16 ` Bondarenko, Anton
2015-10-01 0:16 ` Bondarenko, Anton
[not found] ` <04376A3D786BD947B28569C998A374A62E280E0F-0dz9ie/QGrkPOGHby5MvPNQH9K4/4qFeAL8bYrjMMd8@public.gmane.org>
2015-10-08 9:28 ` Robin Gong
2015-10-08 9:28 ` Robin Gong
2015-10-20 23:08 ` Anton Bondarenko
2015-10-20 23:08 ` Anton Bondarenko
2015-09-25 17:57 ` [PATCH v2 6/8] spi: imx: return error from dma channel request Anton Bondarenko
2015-09-25 17:57 ` Anton Bondarenko
2015-09-30 8:51 ` Robin Gong
2015-09-30 8:51 ` Robin Gong
2015-09-25 17:57 ` [PATCH v2 7/8] spi: imx: defer spi initialization, if DMA engine is pending Anton Bondarenko
2015-09-25 17:57 ` Anton Bondarenko
2015-09-30 8:54 ` Robin Gong
2015-09-30 8:54 ` Robin Gong
[not found] ` <cover.1442923630.git.anton_bondarenko-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
2015-09-25 17:57 ` [PATCH v2 8/8] spi: imx: Add support for SPI Slave mode for imx53 and imx6 chips Anton Bondarenko
2015-09-25 17:57 ` Anton Bondarenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150930083539.GD2709@shlinux2 \
--to=b38343@freescale.com \
--cc=anton_bondarenko@mentor.com \
--cc=broonie@kernel.org \
--cc=jiada_wang@mentor.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=muzaffar_mahmood@relay1.mentorg.com \
--cc=vladimir_zapolskiy@mentor.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.