All of lore.kernel.org
 help / color / mirror / Atom feed
From: Greg KH <gregkh@linuxfoundation.org>
To: Arnd Bergmann <arnd@arndb.de>, linux-kernel@vger.kernel.org
Cc: Johan Hovold <johan@hovoldconsulting.com>,
	Rui Miguel Silva <rmfrfs@gmail.com>,
	Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
	Sandeep Patil <sspatil@google.com>,
	Matt Porter <mporter@kernel.crashing.org>,
	John Stultz <john.stultz@linaro.org>,
	Rob Herring <robh@kernel.org>,
	Viresh Kumar <viresh.kumar@linaro.org>,
	Alex Elder <elder@linaro.org>, David Lin <dtwlin@google.com>,
	"Bryan O'Donoghue" <pure.logic@nexus-software.ie>,
	Vaibhav Agarwal <vaibhav.agarwal@linaro.org>,
	Mark Greer <mgreer@animalcreek.com>
Subject: [patch 21/32] greybus: arche platform driver
Date: Fri, 16 Sep 2016 16:19:47 +0200	[thread overview]
Message-ID: <20160916141947.GA2040@kroah.com> (raw)
In-Reply-To: <20160916064058.GA17821@kroah.com>

This is a platform driver for the arche platform controller that hooks
into the USB hub that talks to the USB<->Unipro bridge chip.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/greybus/arche-apb-ctrl.c |  522 ++++++++++++++++++++++++
 drivers/greybus/arche-platform.c |  828 +++++++++++++++++++++++++++++++++++++++
 drivers/greybus/arche_platform.h |   39 +
 3 files changed, 1389 insertions(+)

--- /dev/null
+++ b/drivers/greybus/arche-apb-ctrl.c
@@ -0,0 +1,522 @@
+/*
+ * Arche Platform driver to control APB.
+ *
+ * Copyright 2014-2015 Google Inc.
+ * Copyright 2014-2015 Linaro Ltd.
+ *
+ * Released under the GPLv2 only.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/of_gpio.h>
+#include <linux/of_irq.h>
+#include <linux/module.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spinlock.h>
+#include "arche_platform.h"
+
+
+struct arche_apb_ctrl_drvdata {
+	/* Control GPIO signals to and from AP <=> AP Bridges */
+	int resetn_gpio;
+	int boot_ret_gpio;
+	int pwroff_gpio;
+	int wake_in_gpio;
+	int wake_out_gpio;
+	int pwrdn_gpio;
+
+	enum arche_platform_state state;
+	bool init_disabled;
+
+	struct regulator *vcore;
+	struct regulator *vio;
+
+	int clk_en_gpio;
+	struct clk *clk;
+
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *pin_default;
+
+	/* V2: SPI Bus control  */
+	int spi_en_gpio;
+	bool spi_en_polarity_high;
+};
+
+/*
+ * Note that these low level api's are active high
+ */
+static inline void deassert_reset(unsigned int gpio)
+{
+	gpio_set_value(gpio, 1);
+}
+
+static inline void assert_reset(unsigned int gpio)
+{
+	gpio_set_value(gpio, 0);
+}
+
+/*
+ * Note: Please do not modify the below sequence, as it is as per the spec
+ */
+static int coldboot_seq(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct arche_apb_ctrl_drvdata *apb = platform_get_drvdata(pdev);
+	int ret;
+
+	if (apb->init_disabled ||
+			apb->state == ARCHE_PLATFORM_STATE_ACTIVE)
+		return 0;
+
+	/* Hold APB in reset state */
+	assert_reset(apb->resetn_gpio);
+
+	if (apb->state == ARCHE_PLATFORM_STATE_FW_FLASHING &&
+			gpio_is_valid(apb->spi_en_gpio))
+		devm_gpio_free(dev, apb->spi_en_gpio);
+
+	/* Enable power to APB */
+	if (!IS_ERR(apb->vcore)) {
+		ret = regulator_enable(apb->vcore);
+		if (ret) {
+			dev_err(dev, "failed to enable core regulator\n");
+			return ret;
+		}
+	}
+
+	if (!IS_ERR(apb->vio)) {
+		ret = regulator_enable(apb->vio);
+		if (ret) {
+			dev_err(dev, "failed to enable IO regulator\n");
+			return ret;
+		}
+	}
+
+	apb_bootret_deassert(dev);
+
+	/* On DB3 clock was not mandatory */
+	if (gpio_is_valid(apb->clk_en_gpio))
+		gpio_set_value(apb->clk_en_gpio, 1);
+
+	usleep_range(100, 200);
+
+	/* deassert reset to APB : Active-low signal */
+	deassert_reset(apb->resetn_gpio);
+
+	apb->state = ARCHE_PLATFORM_STATE_ACTIVE;
+
+	return 0;
+}
+
+static int fw_flashing_seq(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct arche_apb_ctrl_drvdata *apb = platform_get_drvdata(pdev);
+	int ret;
+
+	if (apb->init_disabled ||
+			apb->state == ARCHE_PLATFORM_STATE_FW_FLASHING)
+		return 0;
+
+	ret = regulator_enable(apb->vcore);
+	if (ret) {
+		dev_err(dev, "failed to enable core regulator\n");
+		return ret;
+	}
+
+	ret = regulator_enable(apb->vio);
+	if (ret) {
+		dev_err(dev, "failed to enable IO regulator\n");
+		return ret;
+	}
+
+	if (gpio_is_valid(apb->spi_en_gpio)) {
+		unsigned long flags;
+
+		if (apb->spi_en_polarity_high)
+			flags = GPIOF_OUT_INIT_HIGH;
+		else
+			flags = GPIOF_OUT_INIT_LOW;
+
+		ret = devm_gpio_request_one(dev, apb->spi_en_gpio,
+				flags, "apb_spi_en");
+		if (ret) {
+			dev_err(dev, "Failed requesting SPI bus en gpio %d\n",
+				apb->spi_en_gpio);
+			return ret;
+		}
+	}
+
+	/* for flashing device should be in reset state */
+	assert_reset(apb->resetn_gpio);
+	apb->state = ARCHE_PLATFORM_STATE_FW_FLASHING;
+
+	return 0;
+}
+
+static int standby_boot_seq(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct arche_apb_ctrl_drvdata *apb = platform_get_drvdata(pdev);
+
+	if (apb->init_disabled)
+		return 0;
+
+	/* Even if it is in OFF state, then we do not want to change the state */
+	if (apb->state == ARCHE_PLATFORM_STATE_STANDBY ||
+			apb->state == ARCHE_PLATFORM_STATE_OFF)
+		return 0;
+
+	if (apb->state == ARCHE_PLATFORM_STATE_FW_FLASHING &&
+			gpio_is_valid(apb->spi_en_gpio))
+		devm_gpio_free(dev, apb->spi_en_gpio);
+
+	/*
+	 * As per WDM spec, do nothing
+	 *
+	 * Pasted from WDM spec,
+	 *  - A falling edge on POWEROFF_L is detected (a)
+	 *  - WDM enters standby mode, but no output signals are changed
+	 * */
+
+	/* TODO: POWEROFF_L is input to WDM module  */
+	apb->state = ARCHE_PLATFORM_STATE_STANDBY;
+	return 0;
+}
+
+static void poweroff_seq(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct arche_apb_ctrl_drvdata *apb = platform_get_drvdata(pdev);
+
+	if (apb->init_disabled || apb->state == ARCHE_PLATFORM_STATE_OFF)
+		return;
+
+	if (apb->state == ARCHE_PLATFORM_STATE_FW_FLASHING &&
+			gpio_is_valid(apb->spi_en_gpio))
+		devm_gpio_free(dev, apb->spi_en_gpio);
+
+	/* disable the clock */
+	if (gpio_is_valid(apb->clk_en_gpio))
+		gpio_set_value(apb->clk_en_gpio, 0);
+
+	if (!IS_ERR(apb->vcore) && regulator_is_enabled(apb->vcore) > 0)
+		regulator_disable(apb->vcore);
+
+	if (!IS_ERR(apb->vio) && regulator_is_enabled(apb->vio) > 0)
+		regulator_disable(apb->vio);
+
+	/* As part of exit, put APB back in reset state */
+	assert_reset(apb->resetn_gpio);
+	apb->state = ARCHE_PLATFORM_STATE_OFF;
+
+	/* TODO: May have to send an event to SVC about this exit */
+}
+
+void apb_bootret_assert(struct device *dev)
+{
+	struct arche_apb_ctrl_drvdata *apb = dev_get_drvdata(dev);
+
+	gpio_set_value(apb->boot_ret_gpio, 1);
+}
+
+void apb_bootret_deassert(struct device *dev)
+{
+	struct arche_apb_ctrl_drvdata *apb = dev_get_drvdata(dev);
+
+	gpio_set_value(apb->boot_ret_gpio, 0);
+}
+
+int apb_ctrl_coldboot(struct device *dev)
+{
+	return coldboot_seq(to_platform_device(dev));
+}
+
+int apb_ctrl_fw_flashing(struct device *dev)
+{
+	return fw_flashing_seq(to_platform_device(dev));
+}
+
+int apb_ctrl_standby_boot(struct device *dev)
+{
+	return standby_boot_seq(to_platform_device(dev));
+}
+
+void apb_ctrl_poweroff(struct device *dev)
+{
+	poweroff_seq(to_platform_device(dev));
+}
+
+static ssize_t state_store(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct arche_apb_ctrl_drvdata *apb = platform_get_drvdata(pdev);
+	int ret = 0;
+	bool is_disabled;
+
+	if (sysfs_streq(buf, "off")) {
+		if (apb->state == ARCHE_PLATFORM_STATE_OFF)
+			return count;
+
+		poweroff_seq(pdev);
+	} else if (sysfs_streq(buf, "active")) {
+		if (apb->state == ARCHE_PLATFORM_STATE_ACTIVE)
+			return count;
+
+		poweroff_seq(pdev);
+		is_disabled = apb->init_disabled;
+		apb->init_disabled = false;
+		ret = coldboot_seq(pdev);
+		if (ret)
+			apb->init_disabled = is_disabled;
+	} else if (sysfs_streq(buf, "standby")) {
+		if (apb->state == ARCHE_PLATFORM_STATE_STANDBY)
+			return count;
+
+		ret = standby_boot_seq(pdev);
+	} else if (sysfs_streq(buf, "fw_flashing")) {
+		if (apb->state == ARCHE_PLATFORM_STATE_FW_FLASHING)
+			return count;
+
+		/* First we want to make sure we power off everything
+		 * and then enter FW flashing state */
+		poweroff_seq(pdev);
+		ret = fw_flashing_seq(pdev);
+	} else {
+		dev_err(dev, "unknown state\n");
+		ret = -EINVAL;
+	}
+
+	return ret ? ret : count;
+}
+
+static ssize_t state_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct arche_apb_ctrl_drvdata *apb = dev_get_drvdata(dev);
+
+	switch (apb->state) {
+	case ARCHE_PLATFORM_STATE_OFF:
+		return sprintf(buf, "off%s\n",
+				apb->init_disabled ? ",disabled" : "");
+	case ARCHE_PLATFORM_STATE_ACTIVE:
+		return sprintf(buf, "active\n");
+	case ARCHE_PLATFORM_STATE_STANDBY:
+		return sprintf(buf, "standby\n");
+	case ARCHE_PLATFORM_STATE_FW_FLASHING:
+		return sprintf(buf, "fw_flashing\n");
+	default:
+		return sprintf(buf, "unknown state\n");
+	}
+}
+
+static DEVICE_ATTR_RW(state);
+
+static int apb_ctrl_get_devtree_data(struct platform_device *pdev,
+		struct arche_apb_ctrl_drvdata *apb)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	int ret;
+
+	apb->resetn_gpio = of_get_named_gpio(np, "reset-gpios", 0);
+	if (apb->resetn_gpio < 0) {
+		dev_err(dev, "failed to get reset gpio\n");
+		return apb->resetn_gpio;
+	}
+	ret = devm_gpio_request_one(dev, apb->resetn_gpio,
+			GPIOF_OUT_INIT_LOW, "apb-reset");
+	if (ret) {
+		dev_err(dev, "Failed requesting reset gpio %d\n",
+				apb->resetn_gpio);
+		return ret;
+	}
+
+	apb->boot_ret_gpio = of_get_named_gpio(np, "boot-ret-gpios", 0);
+	if (apb->boot_ret_gpio < 0) {
+		dev_err(dev, "failed to get boot retention gpio\n");
+		return apb->boot_ret_gpio;
+	}
+	ret = devm_gpio_request_one(dev, apb->boot_ret_gpio,
+			GPIOF_OUT_INIT_LOW, "boot retention");
+	if (ret) {
+		dev_err(dev, "Failed requesting bootret gpio %d\n",
+				apb->boot_ret_gpio);
+		return ret;
+	}
+
+	/* It's not mandatory to support power management interface */
+	apb->pwroff_gpio = of_get_named_gpio(np, "pwr-off-gpios", 0);
+	if (apb->pwroff_gpio < 0) {
+		dev_err(dev, "failed to get power off gpio\n");
+		return apb->pwroff_gpio;
+	}
+	ret = devm_gpio_request_one(dev, apb->pwroff_gpio,
+			GPIOF_IN, "pwroff_n");
+	if (ret) {
+		dev_err(dev, "Failed requesting pwroff_n gpio %d\n",
+				apb->pwroff_gpio);
+		return ret;
+	}
+
+	/* Do not make clock mandatory as of now (for DB3) */
+	apb->clk_en_gpio = of_get_named_gpio(np, "clock-en-gpio", 0);
+	if (apb->clk_en_gpio < 0) {
+		dev_warn(dev, "failed to get clock en gpio\n");
+	} else if (gpio_is_valid(apb->clk_en_gpio)) {
+		ret = devm_gpio_request_one(dev, apb->clk_en_gpio,
+				GPIOF_OUT_INIT_LOW, "apb_clk_en");
+		if (ret) {
+			dev_warn(dev, "Failed requesting APB clock en gpio %d\n",
+					apb->clk_en_gpio);
+			return ret;
+		}
+	}
+
+	apb->pwrdn_gpio = of_get_named_gpio(np, "pwr-down-gpios", 0);
+	if (apb->pwrdn_gpio < 0)
+		dev_warn(dev, "failed to get power down gpio\n");
+
+	/* Regulators are optional, as we may have fixed supply coming in */
+	apb->vcore = devm_regulator_get(dev, "vcore");
+	if (IS_ERR(apb->vcore))
+		dev_warn(dev, "no core regulator found\n");
+
+	apb->vio = devm_regulator_get(dev, "vio");
+	if (IS_ERR(apb->vio))
+		dev_warn(dev, "no IO regulator found\n");
+
+	apb->pinctrl = devm_pinctrl_get(&pdev->dev);
+	if (IS_ERR(apb->pinctrl)) {
+		dev_err(&pdev->dev, "could not get pinctrl handle\n");
+		return PTR_ERR(apb->pinctrl);
+	}
+	apb->pin_default = pinctrl_lookup_state(apb->pinctrl, "default");
+	if (IS_ERR(apb->pin_default)) {
+		dev_err(&pdev->dev, "could not get default pin state\n");
+		return PTR_ERR(apb->pin_default);
+	}
+
+	/* Only applicable for platform >= V2 */
+	apb->spi_en_gpio = of_get_named_gpio(np, "spi-en-gpio", 0);
+	if (apb->spi_en_gpio >= 0) {
+		if (of_property_read_bool(pdev->dev.of_node,
+					"spi-en-active-high"))
+			apb->spi_en_polarity_high = true;
+	}
+
+	return 0;
+}
+
+static int arche_apb_ctrl_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct arche_apb_ctrl_drvdata *apb;
+	struct device *dev = &pdev->dev;
+
+	apb = devm_kzalloc(&pdev->dev, sizeof(*apb), GFP_KERNEL);
+	if (!apb)
+		return -ENOMEM;
+
+	ret = apb_ctrl_get_devtree_data(pdev, apb);
+	if (ret) {
+		dev_err(dev, "failed to get apb devicetree data %d\n", ret);
+		return ret;
+	}
+
+	/* Initially set APB to OFF state */
+	apb->state = ARCHE_PLATFORM_STATE_OFF;
+	/* Check whether device needs to be enabled on boot */
+	if (of_property_read_bool(pdev->dev.of_node, "arche,init-disable"))
+		apb->init_disabled = true;
+
+	platform_set_drvdata(pdev, apb);
+
+	/* Create sysfs interface to allow user to change state dynamically */
+	ret = device_create_file(dev, &dev_attr_state);
+	if (ret) {
+		dev_err(dev, "failed to create state file in sysfs\n");
+		return ret;
+	}
+
+	dev_info(&pdev->dev, "Device registered successfully\n");
+	return 0;
+}
+
+static int arche_apb_ctrl_remove(struct platform_device *pdev)
+{
+	device_remove_file(&pdev->dev, &dev_attr_state);
+	poweroff_seq(pdev);
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static int arche_apb_ctrl_suspend(struct device *dev)
+{
+	/*
+	 * If timing profile permits, we may shutdown bridge
+	 * completely
+	 *
+	 * TODO: sequence ??
+	 *
+	 * Also, need to make sure we meet precondition for unipro suspend
+	 * Precondition: Definition ???
+	 */
+	return 0;
+}
+
+static int arche_apb_ctrl_resume(struct device *dev)
+{
+	/*
+	 * Atleast for ES2 we have to meet the delay requirement between
+	 * unipro switch and AP bridge init, depending on whether bridge is in
+	 * OFF state or standby state.
+	 *
+	 * Based on whether bridge is in standby or OFF state we may have to
+	 * assert multiple signals. Please refer to WDM spec, for more info.
+	 *
+	 */
+	return 0;
+}
+
+static void arche_apb_ctrl_shutdown(struct platform_device *pdev)
+{
+	apb_ctrl_poweroff(&pdev->dev);
+}
+
+static SIMPLE_DEV_PM_OPS(arche_apb_ctrl_pm_ops, arche_apb_ctrl_suspend,
+			 arche_apb_ctrl_resume);
+
+static struct of_device_id arche_apb_ctrl_of_match[] = {
+	{ .compatible = "usbffff,2", },
+	{ },
+};
+
+static struct platform_driver arche_apb_ctrl_device_driver = {
+	.probe		= arche_apb_ctrl_probe,
+	.remove		= arche_apb_ctrl_remove,
+	.shutdown	= arche_apb_ctrl_shutdown,
+	.driver		= {
+		.name	= "arche-apb-ctrl",
+		.pm	= &arche_apb_ctrl_pm_ops,
+		.of_match_table = arche_apb_ctrl_of_match,
+	}
+};
+
+int __init arche_apb_init(void)
+{
+	return platform_driver_register(&arche_apb_ctrl_device_driver);
+}
+
+void __exit arche_apb_exit(void)
+{
+	platform_driver_unregister(&arche_apb_ctrl_device_driver);
+}
--- /dev/null
+++ b/drivers/greybus/arche-platform.c
@@ -0,0 +1,828 @@
+/*
+ * Arche Platform driver to enable Unipro link.
+ *
+ * Copyright 2014-2015 Google Inc.
+ * Copyright 2014-2015 Linaro Ltd.
+ *
+ * Released under the GPLv2 only.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/suspend.h>
+#include <linux/time.h>
+#include "arche_platform.h"
+#include "greybus.h"
+
+#include <linux/usb/usb3613.h>
+
+#define WD_COLDBOOT_PULSE_WIDTH_MS	30
+
+enum svc_wakedetect_state {
+	WD_STATE_IDLE,			/* Default state = pulled high/low */
+	WD_STATE_BOOT_INIT,		/* WD = falling edge (low) */
+	WD_STATE_COLDBOOT_TRIG,		/* WD = rising edge (high), > 30msec */
+	WD_STATE_STANDBYBOOT_TRIG,	/* As of now not used ?? */
+	WD_STATE_COLDBOOT_START,	/* Cold boot process started */
+	WD_STATE_STANDBYBOOT_START,	/* Not used */
+	WD_STATE_TIMESYNC,
+};
+
+struct arche_platform_drvdata {
+	/* Control GPIO signals to and from AP <=> SVC */
+	int svc_reset_gpio;
+	bool is_reset_act_hi;
+	int svc_sysboot_gpio;
+	int wake_detect_gpio; /* bi-dir,maps to WAKE_MOD & WAKE_FRAME signals */
+
+	enum arche_platform_state state;
+
+	int svc_refclk_req;
+	struct clk *svc_ref_clk;
+
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *pin_default;
+
+	int num_apbs;
+
+	enum svc_wakedetect_state wake_detect_state;
+	int wake_detect_irq;
+	spinlock_t wake_lock;			/* Protect wake_detect_state */
+	struct mutex platform_state_mutex;	/* Protect state */
+	wait_queue_head_t wq;			/* WQ for arche_pdata->state */
+	unsigned long wake_detect_start;
+	struct notifier_block pm_notifier;
+
+	struct device *dev;
+	struct gb_timesync_svc *timesync_svc_pdata;
+};
+
+static int arche_apb_bootret_assert(struct device *dev, void *data)
+{
+	apb_bootret_assert(dev);
+	return 0;
+}
+
+static int arche_apb_bootret_deassert(struct device *dev, void *data)
+{
+	apb_bootret_deassert(dev);
+	return 0;
+}
+
+/* Requires calling context to hold arche_pdata->platform_state_mutex */
+static void arche_platform_set_state(struct arche_platform_drvdata *arche_pdata,
+				     enum arche_platform_state state)
+{
+	arche_pdata->state = state;
+}
+
+/*
+ * arche_platform_change_state: Change the operational state
+ *
+ * This exported function allows external drivers to change the state
+ * of the arche-platform driver.
+ * Note that this function only supports transitions between two states
+ * with limited functionality.
+ *
+ *  - ARCHE_PLATFORM_STATE_TIME_SYNC:
+ *    Once set, allows timesync operations between SVC <=> AP and makes
+ *    sure that arche-platform driver ignores any subsequent events/pulses
+ *    from SVC over wake/detect.
+ *
+ *  - ARCHE_PLATFORM_STATE_ACTIVE:
+ *    Puts back driver to active state, where any pulse from SVC on wake/detect
+ *    line would trigger either cold/standby boot.
+ *    Note: Transition request from this function does not trigger cold/standby
+ *          boot. It just puts back driver book keeping variable back to ACTIVE
+ *          state and restores the interrupt.
+ *
+ * Returns -ENODEV if device not found, -EAGAIN if the driver cannot currently
+ * satisfy the requested state-transition or -EINVAL for all other
+ * state-transition requests.
+ */
+int arche_platform_change_state(enum arche_platform_state state,
+				struct gb_timesync_svc *timesync_svc_pdata)
+{
+	struct arche_platform_drvdata *arche_pdata;
+	struct platform_device *pdev;
+	struct device_node *np;
+	int ret = -EAGAIN;
+	unsigned long flags;
+
+	np = of_find_compatible_node(NULL, NULL, "google,arche-platform");
+	if (!np) {
+		pr_err("google,arche-platform device node not found\n");
+		return -ENODEV;
+	}
+
+	pdev = of_find_device_by_node(np);
+	if (!pdev) {
+		pr_err("arche-platform device not found\n");
+		return -ENODEV;
+	}
+
+	arche_pdata = platform_get_drvdata(pdev);
+
+	mutex_lock(&arche_pdata->platform_state_mutex);
+	spin_lock_irqsave(&arche_pdata->wake_lock, flags);
+
+	if (arche_pdata->state == state) {
+		ret = 0;
+		goto exit;
+	}
+
+	switch (state) {
+	case ARCHE_PLATFORM_STATE_TIME_SYNC:
+		if (arche_pdata->state != ARCHE_PLATFORM_STATE_ACTIVE) {
+			ret = -EINVAL;
+			goto exit;
+		}
+		if (arche_pdata->wake_detect_state != WD_STATE_IDLE) {
+			dev_err(arche_pdata->dev,
+				"driver busy with wake/detect line ops\n");
+			goto  exit;
+		}
+		device_for_each_child(arche_pdata->dev, NULL,
+				      arche_apb_bootret_assert);
+		arche_pdata->wake_detect_state = WD_STATE_TIMESYNC;
+		break;
+	case ARCHE_PLATFORM_STATE_ACTIVE:
+		if (arche_pdata->state != ARCHE_PLATFORM_STATE_TIME_SYNC) {
+			ret = -EINVAL;
+			goto exit;
+		}
+		device_for_each_child(arche_pdata->dev, NULL,
+				      arche_apb_bootret_deassert);
+		arche_pdata->wake_detect_state = WD_STATE_IDLE;
+		break;
+	case ARCHE_PLATFORM_STATE_OFF:
+	case ARCHE_PLATFORM_STATE_STANDBY:
+	case ARCHE_PLATFORM_STATE_FW_FLASHING:
+		dev_err(arche_pdata->dev, "busy, request to retry later\n");
+		goto exit;
+	default:
+		ret = -EINVAL;
+		dev_err(arche_pdata->dev,
+			"invalid state transition request\n");
+		goto exit;
+	}
+	arche_pdata->timesync_svc_pdata = timesync_svc_pdata;
+	arche_platform_set_state(arche_pdata, state);
+	if (state == ARCHE_PLATFORM_STATE_ACTIVE)
+		wake_up(&arche_pdata->wq);
+
+	ret = 0;
+exit:
+	spin_unlock_irqrestore(&arche_pdata->wake_lock, flags);
+	mutex_unlock(&arche_pdata->platform_state_mutex);
+	of_node_put(np);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(arche_platform_change_state);
+
+/* Requires arche_pdata->wake_lock is held by calling context */
+static void arche_platform_set_wake_detect_state(
+				struct arche_platform_drvdata *arche_pdata,
+				enum svc_wakedetect_state state)
+{
+	arche_pdata->wake_detect_state = state;
+}
+
+static inline void svc_reset_onoff(unsigned int gpio, bool onoff)
+{
+	gpio_set_value(gpio, onoff);
+}
+
+static int apb_cold_boot(struct device *dev, void *data)
+{
+	int ret;
+
+	ret = apb_ctrl_coldboot(dev);
+	if (ret)
+		dev_warn(dev, "failed to coldboot\n");
+
+	/*Child nodes are independent, so do not exit coldboot operation */
+	return 0;
+}
+
+static int apb_poweroff(struct device *dev, void *data)
+{
+	apb_ctrl_poweroff(dev);
+
+	/* Enable HUB3613 into HUB mode. */
+	if (usb3613_hub_mode_ctrl(false))
+		dev_warn(dev, "failed to control hub device\n");
+
+	return 0;
+}
+
+static void arche_platform_wd_irq_en(struct arche_platform_drvdata *arche_pdata)
+{
+	/* Enable interrupt here, to read event back from SVC */
+	gpio_direction_input(arche_pdata->wake_detect_gpio);
+	enable_irq(arche_pdata->wake_detect_irq);
+}
+
+static irqreturn_t arche_platform_wd_irq_thread(int irq, void *devid)
+{
+	struct arche_platform_drvdata *arche_pdata = devid;
+	unsigned long flags;
+
+	spin_lock_irqsave(&arche_pdata->wake_lock, flags);
+	if (arche_pdata->wake_detect_state != WD_STATE_COLDBOOT_TRIG) {
+		/* Something is wrong */
+		spin_unlock_irqrestore(&arche_pdata->wake_lock, flags);
+		return IRQ_HANDLED;
+	}
+
+	arche_platform_set_wake_detect_state(arche_pdata,
+					     WD_STATE_COLDBOOT_START);
+	spin_unlock_irqrestore(&arche_pdata->wake_lock, flags);
+
+	/* It should complete power cycle, so first make sure it is poweroff */
+	device_for_each_child(arche_pdata->dev, NULL, apb_poweroff);
+
+	/* Bring APB out of reset: cold boot sequence */
+	device_for_each_child(arche_pdata->dev, NULL, apb_cold_boot);
+
+	/* Enable HUB3613 into HUB mode. */
+	if (usb3613_hub_mode_ctrl(true))
+		dev_warn(arche_pdata->dev, "failed to control hub device\n");
+
+	spin_lock_irqsave(&arche_pdata->wake_lock, flags);
+	arche_platform_set_wake_detect_state(arche_pdata, WD_STATE_IDLE);
+	spin_unlock_irqrestore(&arche_pdata->wake_lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t arche_platform_wd_irq(int irq, void *devid)
+{
+	struct arche_platform_drvdata *arche_pdata = devid;
+	unsigned long flags;
+
+	spin_lock_irqsave(&arche_pdata->wake_lock, flags);
+
+	if (arche_pdata->wake_detect_state == WD_STATE_TIMESYNC) {
+		gb_timesync_irq(arche_pdata->timesync_svc_pdata);
+		goto exit;
+	}
+
+	if (gpio_get_value(arche_pdata->wake_detect_gpio)) {
+		/* wake/detect rising */
+
+		/*
+		 * If wake/detect line goes high after low, within less than
+		 * 30msec, then standby boot sequence is initiated, which is not
+		 * supported/implemented as of now. So ignore it.
+		 */
+		if (arche_pdata->wake_detect_state == WD_STATE_BOOT_INIT) {
+			if (time_before(jiffies,
+					arche_pdata->wake_detect_start +
+					msecs_to_jiffies(WD_COLDBOOT_PULSE_WIDTH_MS))) {
+				arche_platform_set_wake_detect_state(arche_pdata,
+								     WD_STATE_IDLE);
+			} else {
+				/* Check we are not in middle of irq thread already */
+				if (arche_pdata->wake_detect_state !=
+						WD_STATE_COLDBOOT_START) {
+					arche_platform_set_wake_detect_state(arche_pdata,
+									     WD_STATE_COLDBOOT_TRIG);
+					spin_unlock_irqrestore(
+						&arche_pdata->wake_lock,
+						flags);
+					return IRQ_WAKE_THREAD;
+				}
+			}
+		}
+	} else {
+		/* wake/detect falling */
+		if (arche_pdata->wake_detect_state == WD_STATE_IDLE) {
+			arche_pdata->wake_detect_start = jiffies;
+			/*
+			 * In the begining, when wake/detect goes low (first time), we assume
+			 * it is meant for coldboot and set the flag. If wake/detect line stays low
+			 * beyond 30msec, then it is coldboot else fallback to standby boot.
+			 */
+			arche_platform_set_wake_detect_state(arche_pdata,
+							     WD_STATE_BOOT_INIT);
+		}
+	}
+
+exit:
+	spin_unlock_irqrestore(&arche_pdata->wake_lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Requires arche_pdata->platform_state_mutex to be held
+ */
+static int arche_platform_coldboot_seq(struct arche_platform_drvdata *arche_pdata)
+{
+	int ret;
+
+	if (arche_pdata->state == ARCHE_PLATFORM_STATE_ACTIVE)
+		return 0;
+
+	dev_info(arche_pdata->dev, "Booting from cold boot state\n");
+
+	svc_reset_onoff(arche_pdata->svc_reset_gpio,
+			arche_pdata->is_reset_act_hi);
+
+	gpio_set_value(arche_pdata->svc_sysboot_gpio, 0);
+	usleep_range(100, 200);
+
+	ret = clk_prepare_enable(arche_pdata->svc_ref_clk);
+	if (ret) {
+		dev_err(arche_pdata->dev, "failed to enable svc_ref_clk: %d\n",
+				ret);
+		return ret;
+	}
+
+	/* bring SVC out of reset */
+	svc_reset_onoff(arche_pdata->svc_reset_gpio,
+			!arche_pdata->is_reset_act_hi);
+
+	arche_platform_set_state(arche_pdata, ARCHE_PLATFORM_STATE_ACTIVE);
+
+	return 0;
+}
+
+/*
+ * Requires arche_pdata->platform_state_mutex to be held
+ */
+static int arche_platform_fw_flashing_seq(struct arche_platform_drvdata *arche_pdata)
+{
+	int ret;
+
+	if (arche_pdata->state == ARCHE_PLATFORM_STATE_FW_FLASHING)
+		return 0;
+
+	dev_info(arche_pdata->dev, "Switching to FW flashing state\n");
+
+	svc_reset_onoff(arche_pdata->svc_reset_gpio,
+			arche_pdata->is_reset_act_hi);
+
+	gpio_set_value(arche_pdata->svc_sysboot_gpio, 1);
+
+	usleep_range(100, 200);
+
+	ret = clk_prepare_enable(arche_pdata->svc_ref_clk);
+	if (ret) {
+		dev_err(arche_pdata->dev, "failed to enable svc_ref_clk: %d\n",
+				ret);
+		return ret;
+	}
+
+	svc_reset_onoff(arche_pdata->svc_reset_gpio,
+			!arche_pdata->is_reset_act_hi);
+
+	arche_platform_set_state(arche_pdata, ARCHE_PLATFORM_STATE_FW_FLASHING);
+
+	return 0;
+}
+
+/*
+ * Requires arche_pdata->platform_state_mutex to be held
+ */
+static void arche_platform_poweroff_seq(struct arche_platform_drvdata *arche_pdata)
+{
+	unsigned long flags;
+
+	if (arche_pdata->state == ARCHE_PLATFORM_STATE_OFF)
+		return;
+
+	/* If in fw_flashing mode, then no need to repeate things again */
+	if (arche_pdata->state != ARCHE_PLATFORM_STATE_FW_FLASHING) {
+		disable_irq(arche_pdata->wake_detect_irq);
+
+		spin_lock_irqsave(&arche_pdata->wake_lock, flags);
+		arche_platform_set_wake_detect_state(arche_pdata,
+						     WD_STATE_IDLE);
+		spin_unlock_irqrestore(&arche_pdata->wake_lock, flags);
+	}
+
+	clk_disable_unprepare(arche_pdata->svc_ref_clk);
+
+	/* As part of exit, put APB back in reset state */
+	svc_reset_onoff(arche_pdata->svc_reset_gpio,
+			arche_pdata->is_reset_act_hi);
+
+	arche_platform_set_state(arche_pdata, ARCHE_PLATFORM_STATE_OFF);
+}
+
+static ssize_t state_store(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct arche_platform_drvdata *arche_pdata = platform_get_drvdata(pdev);
+	int ret = 0;
+
+retry:
+	mutex_lock(&arche_pdata->platform_state_mutex);
+	if (arche_pdata->state == ARCHE_PLATFORM_STATE_TIME_SYNC) {
+		mutex_unlock(&arche_pdata->platform_state_mutex);
+		ret = wait_event_interruptible(
+			arche_pdata->wq,
+			arche_pdata->state != ARCHE_PLATFORM_STATE_TIME_SYNC);
+		if (ret)
+			return ret;
+		goto retry;
+	}
+
+	if (sysfs_streq(buf, "off")) {
+		if (arche_pdata->state == ARCHE_PLATFORM_STATE_OFF)
+			goto exit;
+
+		/*  If SVC goes down, bring down APB's as well */
+		device_for_each_child(arche_pdata->dev, NULL, apb_poweroff);
+
+		arche_platform_poweroff_seq(arche_pdata);
+
+	} else if (sysfs_streq(buf, "active")) {
+		if (arche_pdata->state == ARCHE_PLATFORM_STATE_ACTIVE)
+			goto exit;
+
+		/* First we want to make sure we power off everything
+		 * and then activate back again */
+		device_for_each_child(arche_pdata->dev, NULL, apb_poweroff);
+		arche_platform_poweroff_seq(arche_pdata);
+
+		arche_platform_wd_irq_en(arche_pdata);
+		ret = arche_platform_coldboot_seq(arche_pdata);
+		if (ret)
+			goto exit;
+
+	} else if (sysfs_streq(buf, "standby")) {
+		if (arche_pdata->state == ARCHE_PLATFORM_STATE_STANDBY)
+			goto exit;
+
+		dev_warn(arche_pdata->dev, "standby state not supported\n");
+	} else if (sysfs_streq(buf, "fw_flashing")) {
+		if (arche_pdata->state == ARCHE_PLATFORM_STATE_FW_FLASHING)
+			goto exit;
+
+		/*
+		 * Here we only control SVC.
+		 *
+		 * In case of FW_FLASHING mode we do not want to control
+		 * APBs, as in case of V2, SPI bus is shared between both
+		 * the APBs. So let user chose which APB he wants to flash.
+		 */
+		arche_platform_poweroff_seq(arche_pdata);
+
+		ret = arche_platform_fw_flashing_seq(arche_pdata);
+		if (ret)
+			goto exit;
+	} else {
+		dev_err(arche_pdata->dev, "unknown state\n");
+		ret = -EINVAL;
+	}
+
+exit:
+	mutex_unlock(&arche_pdata->platform_state_mutex);
+	return ret ? ret : count;
+}
+
+static ssize_t state_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct arche_platform_drvdata *arche_pdata = dev_get_drvdata(dev);
+
+	switch (arche_pdata->state) {
+	case ARCHE_PLATFORM_STATE_OFF:
+		return sprintf(buf, "off\n");
+	case ARCHE_PLATFORM_STATE_ACTIVE:
+		return sprintf(buf, "active\n");
+	case ARCHE_PLATFORM_STATE_STANDBY:
+		return sprintf(buf, "standby\n");
+	case ARCHE_PLATFORM_STATE_FW_FLASHING:
+		return sprintf(buf, "fw_flashing\n");
+	case ARCHE_PLATFORM_STATE_TIME_SYNC:
+		return sprintf(buf, "time_sync\n");
+	default:
+		return sprintf(buf, "unknown state\n");
+	}
+}
+
+static DEVICE_ATTR_RW(state);
+
+static int arche_platform_pm_notifier(struct notifier_block *notifier,
+				      unsigned long pm_event, void *unused)
+{
+	struct arche_platform_drvdata *arche_pdata =
+		container_of(notifier, struct arche_platform_drvdata,
+			     pm_notifier);
+	int ret = NOTIFY_DONE;
+
+	mutex_lock(&arche_pdata->platform_state_mutex);
+	switch (pm_event) {
+	case PM_SUSPEND_PREPARE:
+		if (arche_pdata->state != ARCHE_PLATFORM_STATE_ACTIVE) {
+			ret = NOTIFY_STOP;
+			break;
+		}
+		device_for_each_child(arche_pdata->dev, NULL, apb_poweroff);
+		arche_platform_poweroff_seq(arche_pdata);
+		break;
+	case PM_POST_SUSPEND:
+		if (arche_pdata->state != ARCHE_PLATFORM_STATE_OFF)
+			break;
+
+		arche_platform_wd_irq_en(arche_pdata);
+		arche_platform_coldboot_seq(arche_pdata);
+		break;
+	default:
+		break;
+	}
+	mutex_unlock(&arche_pdata->platform_state_mutex);
+
+	return ret;
+}
+
+static int arche_platform_probe(struct platform_device *pdev)
+{
+	struct arche_platform_drvdata *arche_pdata;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	int ret;
+
+	arche_pdata = devm_kzalloc(&pdev->dev, sizeof(*arche_pdata), GFP_KERNEL);
+	if (!arche_pdata)
+		return -ENOMEM;
+
+	/* setup svc reset gpio */
+	arche_pdata->is_reset_act_hi = of_property_read_bool(np,
+					"svc,reset-active-high");
+	arche_pdata->svc_reset_gpio = of_get_named_gpio(np, "svc,reset-gpio", 0);
+	if (arche_pdata->svc_reset_gpio < 0) {
+		dev_err(dev, "failed to get reset-gpio\n");
+		return arche_pdata->svc_reset_gpio;
+	}
+	ret = devm_gpio_request(dev, arche_pdata->svc_reset_gpio, "svc-reset");
+	if (ret) {
+		dev_err(dev, "failed to request svc-reset gpio:%d\n", ret);
+		return ret;
+	}
+	ret = gpio_direction_output(arche_pdata->svc_reset_gpio,
+					arche_pdata->is_reset_act_hi);
+	if (ret) {
+		dev_err(dev, "failed to set svc-reset gpio dir:%d\n", ret);
+		return ret;
+	}
+	arche_platform_set_state(arche_pdata, ARCHE_PLATFORM_STATE_OFF);
+
+	arche_pdata->svc_sysboot_gpio = of_get_named_gpio(np,
+					"svc,sysboot-gpio", 0);
+	if (arche_pdata->svc_sysboot_gpio < 0) {
+		dev_err(dev, "failed to get sysboot gpio\n");
+		return arche_pdata->svc_sysboot_gpio;
+	}
+	ret = devm_gpio_request(dev, arche_pdata->svc_sysboot_gpio, "sysboot0");
+	if (ret) {
+		dev_err(dev, "failed to request sysboot0 gpio:%d\n", ret);
+		return ret;
+	}
+	ret = gpio_direction_output(arche_pdata->svc_sysboot_gpio, 0);
+	if (ret) {
+		dev_err(dev, "failed to set svc-reset gpio dir:%d\n", ret);
+		return ret;
+	}
+
+	/* setup the clock request gpio first */
+	arche_pdata->svc_refclk_req = of_get_named_gpio(np,
+					"svc,refclk-req-gpio", 0);
+	if (arche_pdata->svc_refclk_req < 0) {
+		dev_err(dev, "failed to get svc clock-req gpio\n");
+		return arche_pdata->svc_refclk_req;
+	}
+	ret = devm_gpio_request(dev, arche_pdata->svc_refclk_req, "svc-clk-req");
+	if (ret) {
+		dev_err(dev, "failed to request svc-clk-req gpio: %d\n", ret);
+		return ret;
+	}
+	ret = gpio_direction_input(arche_pdata->svc_refclk_req);
+	if (ret) {
+		dev_err(dev, "failed to set svc-clk-req gpio dir :%d\n", ret);
+		return ret;
+	}
+
+	/* setup refclk2 to follow the pin */
+	arche_pdata->svc_ref_clk = devm_clk_get(dev, "svc_ref_clk");
+	if (IS_ERR(arche_pdata->svc_ref_clk)) {
+		ret = PTR_ERR(arche_pdata->svc_ref_clk);
+		dev_err(dev, "failed to get svc_ref_clk: %d\n", ret);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, arche_pdata);
+
+	arche_pdata->num_apbs = of_get_child_count(np);
+	dev_dbg(dev, "Number of APB's available - %d\n", arche_pdata->num_apbs);
+
+	arche_pdata->wake_detect_gpio = of_get_named_gpio(np, "svc,wake-detect-gpio", 0);
+	if (arche_pdata->wake_detect_gpio < 0) {
+		dev_err(dev, "failed to get wake detect gpio\n");
+		ret = arche_pdata->wake_detect_gpio;
+		return ret;
+	}
+
+	ret = devm_gpio_request(dev, arche_pdata->wake_detect_gpio, "wake detect");
+	if (ret) {
+		dev_err(dev, "Failed requesting wake_detect gpio %d\n",
+				arche_pdata->wake_detect_gpio);
+		return ret;
+	}
+
+	arche_platform_set_wake_detect_state(arche_pdata, WD_STATE_IDLE);
+
+	arche_pdata->dev = &pdev->dev;
+
+	spin_lock_init(&arche_pdata->wake_lock);
+	mutex_init(&arche_pdata->platform_state_mutex);
+	init_waitqueue_head(&arche_pdata->wq);
+	arche_pdata->wake_detect_irq =
+		gpio_to_irq(arche_pdata->wake_detect_gpio);
+
+	ret = devm_request_threaded_irq(dev, arche_pdata->wake_detect_irq,
+			arche_platform_wd_irq,
+			arche_platform_wd_irq_thread,
+			IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING | IRQF_ONESHOT,
+			dev_name(dev), arche_pdata);
+	if (ret) {
+		dev_err(dev, "failed to request wake detect IRQ %d\n", ret);
+		return ret;
+	}
+	disable_irq(arche_pdata->wake_detect_irq);
+
+	ret = device_create_file(dev, &dev_attr_state);
+	if (ret) {
+		dev_err(dev, "failed to create state file in sysfs\n");
+		return ret;
+	}
+
+	ret = of_platform_populate(np, NULL, NULL, dev);
+	if (ret) {
+		dev_err(dev, "failed to populate child nodes %d\n", ret);
+		goto err_device_remove;
+	}
+
+	arche_pdata->pm_notifier.notifier_call = arche_platform_pm_notifier;
+	ret = register_pm_notifier(&arche_pdata->pm_notifier);
+
+	if (ret) {
+		dev_err(dev, "failed to register pm notifier %d\n", ret);
+		goto err_device_remove;
+	}
+
+	/* Register callback pointer */
+	arche_platform_change_state_cb = arche_platform_change_state;
+
+	/* Explicitly power off if requested */
+	if (!of_property_read_bool(pdev->dev.of_node, "arche,init-off")) {
+		mutex_lock(&arche_pdata->platform_state_mutex);
+		ret = arche_platform_coldboot_seq(arche_pdata);
+		if (ret) {
+			dev_err(dev, "Failed to cold boot svc %d\n", ret);
+			goto err_coldboot;
+		}
+		arche_platform_wd_irq_en(arche_pdata);
+		mutex_unlock(&arche_pdata->platform_state_mutex);
+	}
+
+	dev_info(dev, "Device registered successfully\n");
+	return 0;
+
+err_coldboot:
+	mutex_unlock(&arche_pdata->platform_state_mutex);
+err_device_remove:
+	device_remove_file(&pdev->dev, &dev_attr_state);
+	return ret;
+}
+
+static int arche_remove_child(struct device *dev, void *unused)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+
+	platform_device_unregister(pdev);
+
+	return 0;
+}
+
+static int arche_platform_remove(struct platform_device *pdev)
+{
+	struct arche_platform_drvdata *arche_pdata = platform_get_drvdata(pdev);
+
+	unregister_pm_notifier(&arche_pdata->pm_notifier);
+	device_remove_file(&pdev->dev, &dev_attr_state);
+	device_for_each_child(&pdev->dev, NULL, arche_remove_child);
+	arche_platform_poweroff_seq(arche_pdata);
+	platform_set_drvdata(pdev, NULL);
+
+	if (usb3613_hub_mode_ctrl(false))
+		dev_warn(arche_pdata->dev, "failed to control hub device\n");
+		/* TODO: Should we do anything more here ?? */
+	return 0;
+}
+
+static int arche_platform_suspend(struct device *dev)
+{
+	/*
+	 * If timing profile premits, we may shutdown bridge
+	 * completely
+	 *
+	 * TODO: sequence ??
+	 *
+	 * Also, need to make sure we meet precondition for unipro suspend
+	 * Precondition: Definition ???
+	 */
+	return 0;
+}
+
+static int arche_platform_resume(struct device *dev)
+{
+	/*
+	 * Atleast for ES2 we have to meet the delay requirement between
+	 * unipro switch and AP bridge init, depending on whether bridge is in
+	 * OFF state or standby state.
+	 *
+	 * Based on whether bridge is in standby or OFF state we may have to
+	 * assert multiple signals. Please refer to WDM spec, for more info.
+	 *
+	 */
+	return 0;
+}
+
+static void arche_platform_shutdown(struct platform_device *pdev)
+{
+	struct arche_platform_drvdata *arche_pdata = platform_get_drvdata(pdev);
+
+	arche_platform_poweroff_seq(arche_pdata);
+
+	usb3613_hub_mode_ctrl(false);
+}
+
+static SIMPLE_DEV_PM_OPS(arche_platform_pm_ops,
+			arche_platform_suspend,
+			arche_platform_resume);
+
+static struct of_device_id arche_platform_of_match[] = {
+	{ .compatible = "google,arche-platform", }, /* Use PID/VID of SVC device */
+	{ },
+};
+
+static struct of_device_id arche_combined_id[] = {
+	{ .compatible = "google,arche-platform", }, /* Use PID/VID of SVC device */
+	{ .compatible = "usbffff,2", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, arche_combined_id);
+
+static struct platform_driver arche_platform_device_driver = {
+	.probe		= arche_platform_probe,
+	.remove		= arche_platform_remove,
+	.shutdown	= arche_platform_shutdown,
+	.driver		= {
+		.name	= "arche-platform-ctrl",
+		.pm	= &arche_platform_pm_ops,
+		.of_match_table = arche_platform_of_match,
+	}
+};
+
+static int __init arche_init(void)
+{
+	int retval;
+
+	retval = platform_driver_register(&arche_platform_device_driver);
+	if (retval)
+		return retval;
+
+	retval = arche_apb_init();
+	if (retval)
+		platform_driver_unregister(&arche_platform_device_driver);
+
+	return retval;
+}
+module_init(arche_init);
+
+static void __exit arche_exit(void)
+{
+	arche_apb_exit();
+	platform_driver_unregister(&arche_platform_device_driver);
+}
+module_exit(arche_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Vaibhav Hiremath <vaibhav.hiremath@linaro.org>");
+MODULE_DESCRIPTION("Arche Platform Driver");
--- /dev/null
+++ b/drivers/greybus/arche_platform.h
@@ -0,0 +1,39 @@
+/*
+ * Arche Platform driver to enable Unipro link.
+ *
+ * Copyright 2015-2016 Google Inc.
+ * Copyright 2015-2016 Linaro Ltd.
+ *
+ * Released under the GPLv2 only.
+ */
+
+#ifndef __ARCHE_PLATFORM_H
+#define __ARCHE_PLATFORM_H
+
+#include "timesync.h"
+
+enum arche_platform_state {
+	ARCHE_PLATFORM_STATE_OFF,
+	ARCHE_PLATFORM_STATE_ACTIVE,
+	ARCHE_PLATFORM_STATE_STANDBY,
+	ARCHE_PLATFORM_STATE_FW_FLASHING,
+	ARCHE_PLATFORM_STATE_TIME_SYNC,
+};
+
+int arche_platform_change_state(enum arche_platform_state state,
+				struct gb_timesync_svc *pdata);
+
+extern int (*arche_platform_change_state_cb)(enum arche_platform_state state,
+					     struct gb_timesync_svc *pdata);
+int __init arche_apb_init(void);
+void __exit arche_apb_exit(void);
+
+/* Operational states for the APB device */
+int apb_ctrl_coldboot(struct device *dev);
+int apb_ctrl_fw_flashing(struct device *dev);
+int apb_ctrl_standby_boot(struct device *dev);
+void apb_ctrl_poweroff(struct device *dev);
+void apb_bootret_assert(struct device *dev);
+void apb_bootret_deassert(struct device *dev);
+
+#endif	/* __ARCHE_PLATFORM_H */

  parent reply	other threads:[~2016-09-16 14:19 UTC|newest]

Thread overview: 84+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-09-14 10:09 [GIT PULL] Greybus driver subsystem for 4.9-rc1 Greg KH
2016-09-14 17:36 ` Mark Rutland
2016-09-14 17:36   ` Mark Rutland
2016-09-14 18:07   ` Greg KH
2016-09-14 18:07     ` Greg KH
2016-09-14 18:29     ` Greg KH
2016-09-14 18:29       ` Greg KH
2016-09-14 19:05       ` Joe Perches
2016-09-14 19:05         ` Joe Perches
2016-09-15  9:35       ` Bryan O'Donoghue
2016-09-15  9:35         ` Bryan O'Donoghue
2016-09-15 10:13         ` Mark Rutland
2016-09-15 10:13           ` Mark Rutland
2016-09-15 10:35           ` Bryan O'Donoghue
2016-09-15 10:35             ` Bryan O'Donoghue
2016-09-15 10:47             ` Bryan O'Donoghue
2016-09-15 10:47               ` Bryan O'Donoghue
2016-09-15 11:20             ` Mark Rutland
2016-09-15 11:20               ` Mark Rutland
2016-09-15 11:48               ` Bryan O'Donoghue
2016-09-15 11:48                 ` Bryan O'Donoghue
2016-09-15 12:46                 ` Mark Rutland
2016-09-15 12:46                   ` Mark Rutland
2016-09-15 15:40                   ` Bryan O'Donoghue
2016-09-15 15:40                     ` Bryan O'Donoghue
2016-09-15 15:47                     ` Mark Rutland
2016-09-15 15:47                       ` Mark Rutland
2016-09-15 16:09                       ` Bryan O'Donoghue
2016-09-15 16:09                         ` Bryan O'Donoghue
2016-09-14 20:07     ` Rob Herring
2016-09-14 20:07       ` Rob Herring
2016-09-15 10:17       ` Greg KH
2016-09-15 10:17         ` Greg KH
2016-09-15 11:02         ` Bryan O'Donoghue
2016-09-15 11:02           ` Bryan O'Donoghue
     [not found] ` <20160915122141.650632149@bubbles.kroah.org>
     [not found]   ` <20160915122234.640367870@bubbles.kroah.org>
2016-09-15 13:16     ` [patch 11/32] greybus: camera driver Laurent Pinchart
2016-09-15 14:45 ` [GIT PULL] Greybus driver subsystem for 4.9-rc1 Mark Brown
2016-09-16  6:05   ` Greg KH
2016-09-16 10:18     ` Mark Brown
2016-09-16 13:22       ` Greg KH
2016-09-16 14:24         ` Greg KH
2016-09-20  6:41           ` Greg KH
2016-09-20  7:12             ` Vaibhav Agarwal
2016-09-16 12:18     ` Arnd Bergmann
2016-09-21 13:02     ` Mark Rutland
2016-09-21 14:13       ` Greg KH
2016-09-16  6:40 ` [patch 00/32] Greybus driver subsystem Greg KH
2016-09-16  6:41   ` [patch 02/32] greybus: interface control logic Greg KH
2016-09-16 13:22   ` [patch 03/32] greybus: operations logic Greg KH
2016-09-16 13:23   ` [patch 04/32] greybus: host driver framework Greg KH
2016-09-16 13:23   ` [patch 05/32] greybus: trace.h Greg KH
2016-09-16 13:23   ` [patch 06/32] greybus: svc driver/watchdog Greg KH
2016-09-16 13:23   ` [patch 07/32] greybus: core code Greg KH
2016-09-16 13:24   ` [patch 08/32] greybus: bootrom driver Greg KH
2016-09-16 13:24   ` [patch 09/32] greybus: firmware download class driver Greg KH
2016-09-16 13:24   ` [patch 10/32] greybus: audio driver Greg KH
2016-09-16 13:25   ` [patch 11/32] greybus: camera driver Greg KH
2016-09-16 13:25   ` [patch 12/32] greybus: es2 host driver Greg KH
2016-10-07 13:43     ` Pavel Machek
2016-09-16 14:09   ` [patch 13/32] greybus: HID driver Greg KH
2016-09-16 14:10   ` [patch 14/32] greybus: LED driver Greg KH
2016-10-07 13:36     ` Pavel Machek
2016-10-07 13:41       ` Greg KH
2016-09-16 14:10   ` [patch 15/32] greybus: logging driver Greg KH
2016-09-16 14:10   ` [patch 16/32] greybus: loopback driver Greg KH
2016-09-16 14:10   ` [patch 17/32] greybus: power supply driver Greg KH
2016-10-07 13:49     ` Pavel Machek
2016-10-07 14:12       ` Greg KH
2016-10-07 18:15         ` Pavel Machek
2016-09-16 14:11   ` [patch 18/32] greybus: raw driver Greg KH
2016-09-16 14:11   ` [patch 19/32] greybus: timesync driver Greg KH
2016-09-16 14:11   ` [patch 20/32] greybus: vibrator driver Greg KH
2016-09-16 14:19   ` Greg KH [this message]
2016-09-16 14:20   ` [patch 22/32] greybus: bridged phy bus code Greg KH
2016-09-16 14:20   ` [patch 23/32] greybus: bridged phy gpio driver Greg KH
2016-09-16 14:20   ` [patch 24/32] greybus: bridged phy i2c driver Greg KH
2016-09-16 14:20   ` [patch 25/32] greybus: bridged phy pwm driver Greg KH
2016-09-16 14:21   ` [patch 26/32] greybus: bridged phy sdio driver Greg KH
2016-09-16 14:21   ` [patch 27/32] greybus: bridged phy spi driver Greg KH
2016-09-16 14:21   ` [patch 28/32] greybus: bridged phy uart driver Greg KH
2016-09-16 14:21   ` [patch 29/32] greybus: bridged phy usb driver Greg KH
2016-09-16 14:22   ` [patch 30/32] greybus: tools Greg KH
2016-09-16 14:22   ` [patch 31/32] greybus: documentation Greg KH
2016-09-16 14:22   ` [patch 32/32] greybus: add to the build Greg KH

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20160916141947.GA2040@kroah.com \
    --to=gregkh@linuxfoundation.org \
    --cc=arnd@arndb.de \
    --cc=dtwlin@google.com \
    --cc=elder@linaro.org \
    --cc=johan@hovoldconsulting.com \
    --cc=john.stultz@linaro.org \
    --cc=laurent.pinchart@ideasonboard.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mgreer@animalcreek.com \
    --cc=mporter@kernel.crashing.org \
    --cc=pure.logic@nexus-software.ie \
    --cc=rmfrfs@gmail.com \
    --cc=robh@kernel.org \
    --cc=sspatil@google.com \
    --cc=vaibhav.agarwal@linaro.org \
    --cc=viresh.kumar@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.