From: f.fainelli@gmail.com (Florian Fainelli)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH net-next v2 10/10] ARM: orion: Register DSA switch as a MDIO device
Date: Wed, 11 Jan 2017 19:41:21 -0800 [thread overview]
Message-ID: <20170112034121.27697-11-f.fainelli@gmail.com> (raw)
In-Reply-To: <20170112034121.27697-1-f.fainelli@gmail.com>
Utilize the ability to pass board specific MDIO bus information towards a
particular MDIO device thus allowing us to provide the per-port switch layout
to the Marvell 88E6XXX switch driver.
Since we would end-up with conflicting registration paths, do not register the
"dsa" platform device anymore.
Note that the MDIO devices registered by code in net/dsa/dsa2.c does not
parse a dsa_platform_data, but directly take a dsa_chip_data (specific
to a single switch chip), so we update the different call sites to pass
this structure down to orion_ge00_switch_init().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm/mach-orion5x/common.c | 2 +-
arch/arm/mach-orion5x/common.h | 4 ++--
arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c | 7 +------
arch/arm/mach-orion5x/rd88f5181l-ge-setup.c | 7 +------
arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c | 7 +------
arch/arm/mach-orion5x/wnr854t-setup.c | 2 +-
arch/arm/mach-orion5x/wrt350n-v2-setup.c | 7 +------
arch/arm/plat-orion/common.c | 25 +++++++++++++++++++------
arch/arm/plat-orion/include/plat/common.h | 4 ++--
9 files changed, 29 insertions(+), 36 deletions(-)
diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c
index 04910764c385..83a7ec4c16d0 100644
--- a/arch/arm/mach-orion5x/common.c
+++ b/arch/arm/mach-orion5x/common.c
@@ -105,7 +105,7 @@ void __init orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data)
/*****************************************************************************
* Ethernet switch
****************************************************************************/
-void __init orion5x_eth_switch_init(struct dsa_platform_data *d)
+void __init orion5x_eth_switch_init(struct dsa_chip_data *d)
{
orion_ge00_switch_init(d);
}
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index 8a4115bd441d..efeffc6b4ebb 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -3,7 +3,7 @@
#include <linux/reboot.h>
-struct dsa_platform_data;
+struct dsa_chip_data;
struct mv643xx_eth_platform_data;
struct mv_sata_platform_data;
@@ -41,7 +41,7 @@ void orion5x_setup_wins(void);
void orion5x_ehci0_init(void);
void orion5x_ehci1_init(void);
void orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data);
-void orion5x_eth_switch_init(struct dsa_platform_data *d);
+void orion5x_eth_switch_init(struct dsa_chip_data *d);
void orion5x_i2c_init(void);
void orion5x_sata_init(struct mv_sata_platform_data *sata_data);
void orion5x_spi_init(void);
diff --git a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
index dccadf68ea2b..a3c1336d30c9 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
@@ -101,11 +101,6 @@ static struct dsa_chip_data rd88f5181l_fxo_switch_chip_data = {
.port_names[7] = "lan3",
};
-static struct dsa_platform_data __initdata rd88f5181l_fxo_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f5181l_fxo_switch_chip_data,
-};
-
static void __init rd88f5181l_fxo_init(void)
{
/*
@@ -120,7 +115,7 @@ static void __init rd88f5181l_fxo_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_fxo_eth_data);
- orion5x_eth_switch_init(&rd88f5181l_fxo_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f5181l_fxo_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
index affe5ec825de..252efe29bd1a 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
@@ -102,11 +102,6 @@ static struct dsa_chip_data rd88f5181l_ge_switch_chip_data = {
.port_names[7] = "lan3",
};
-static struct dsa_platform_data __initdata rd88f5181l_ge_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f5181l_ge_switch_chip_data,
-};
-
static struct i2c_board_info __initdata rd88f5181l_ge_i2c_rtc = {
I2C_BOARD_INFO("ds1338", 0x68),
};
@@ -125,7 +120,7 @@ static void __init rd88f5181l_ge_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_ge_eth_data);
- orion5x_eth_switch_init(&rd88f5181l_ge_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f5181l_ge_switch_chip_data);
orion5x_i2c_init();
orion5x_uart0_init();
diff --git a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
index 67ee8571b03c..f4f1dbe1d91d 100644
--- a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
@@ -40,11 +40,6 @@ static struct dsa_chip_data rd88f6183ap_ge_switch_chip_data = {
.port_names[5] = "cpu",
};
-static struct dsa_platform_data __initdata rd88f6183ap_ge_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f6183ap_ge_switch_chip_data,
-};
-
static struct mtd_partition rd88f6183ap_ge_partitions[] = {
{
.name = "kernel",
@@ -89,7 +84,7 @@ static void __init rd88f6183ap_ge_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f6183ap_ge_eth_data);
- orion5x_eth_switch_init(&rd88f6183ap_ge_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f6183ap_ge_switch_chip_data);
spi_register_board_info(rd88f6183ap_ge_spi_slave_info,
ARRAY_SIZE(rd88f6183ap_ge_spi_slave_info));
orion5x_spi_init();
diff --git a/arch/arm/mach-orion5x/wnr854t-setup.c b/arch/arm/mach-orion5x/wnr854t-setup.c
index 4dbcdbe1de7c..ac3376fc269f 100644
--- a/arch/arm/mach-orion5x/wnr854t-setup.c
+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
@@ -124,7 +124,7 @@ static void __init wnr854t_init(void)
* Configure peripherals.
*/
orion5x_eth_init(&wnr854t_eth_data);
- orion5x_eth_switch_init(&wnr854t_switch_plat_data);
+ orion5x_eth_switch_init(&wnr854t_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
index a6a8c4648d74..9250bb2e429c 100644
--- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
@@ -191,11 +191,6 @@ static struct dsa_chip_data wrt350n_v2_switch_chip_data = {
.port_names[7] = "lan4",
};
-static struct dsa_platform_data __initdata wrt350n_v2_switch_plat_data = {
- .nr_chips = 1,
- .chip = &wrt350n_v2_switch_chip_data,
-};
-
static void __init wrt350n_v2_init(void)
{
/*
@@ -210,7 +205,7 @@ static void __init wrt350n_v2_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&wrt350n_v2_eth_data);
- orion5x_eth_switch_init(&wrt350n_v2_switch_plat_data);
+ orion5x_eth_switch_init(&wrt350n_v2_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/plat-orion/common.c b/arch/arm/plat-orion/common.c
index 272f49b2c68f..989f3ccfcdc7 100644
--- a/arch/arm/plat-orion/common.c
+++ b/arch/arm/plat-orion/common.c
@@ -22,6 +22,7 @@
#include <linux/platform_data/dma-mv_xor.h>
#include <linux/platform_data/usb-ehci-orion.h>
#include <plat/common.h>
+#include <linux/phy.h>
/* Create a clkdev entry for a given device/clk */
void __init orion_clkdev_add(const char *con_id, const char *dev_id,
@@ -470,15 +471,27 @@ void __init orion_ge11_init(struct mv643xx_eth_platform_data *eth_data,
/*****************************************************************************
* Ethernet switch
****************************************************************************/
-void __init orion_ge00_switch_init(struct dsa_platform_data *d)
+static __initdata const char *orion_ge00_mvmdio_bus_name = "orion-mii";
+static __initdata struct mdio_board_info
+ orion_ge00_switch_board_info;
+
+void __init orion_ge00_switch_init(struct dsa_chip_data *d)
{
- int i;
+ struct mdio_board_info *bd;
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(d->port_names); i++)
+ if (!strcmp(d->port_names[i], "cpu"))
+ break;
- d->netdev = &orion_ge00.dev;
- for (i = 0; i < d->nr_chips; i++)
- d->chip[i].host_dev = &orion_ge_mvmdio.dev;
+ bd = &orion_ge00_switch_board_info;
+ bd->bus_id = orion_ge00_mvmdio_bus_name;
+ bd->mdio_addr = d->sw_addr;
+ d->netdev[i] = &orion_ge00.dev;
+ strcpy(bd->modalias, "mv88e6085");
+ bd->platform_data = d;
- platform_device_register_data(NULL, "dsa", 0, d, sizeof(d));
+ mdiobus_register_board_info(&orion_ge00_switch_board_info, 1);
}
/*****************************************************************************
diff --git a/arch/arm/plat-orion/include/plat/common.h b/arch/arm/plat-orion/include/plat/common.h
index 9347f3c58a6d..3647d3b33c20 100644
--- a/arch/arm/plat-orion/include/plat/common.h
+++ b/arch/arm/plat-orion/include/plat/common.h
@@ -12,7 +12,7 @@
#include <linux/mv643xx_eth.h>
#include <linux/platform_data/usb-ehci-orion.h>
-struct dsa_platform_data;
+struct dsa_chip_data;
struct mv_sata_platform_data;
void __init orion_uart0_init(void __iomem *membase,
@@ -57,7 +57,7 @@ void __init orion_ge11_init(struct mv643xx_eth_platform_data *eth_data,
unsigned long mapbase,
unsigned long irq);
-void __init orion_ge00_switch_init(struct dsa_platform_data *d);
+void __init orion_ge00_switch_init(struct dsa_chip_data *d);
void __init orion_i2c_init(unsigned long mapbase,
unsigned long irq,
--
2.9.3
WARNING: multiple messages have this Message-ID (diff)
From: Florian Fainelli <f.fainelli@gmail.com>
To: netdev@vger.kernel.org
Cc: Florian Fainelli <f.fainelli@gmail.com>,
Jason Cooper <jason@lakedaemon.net>, Andrew Lunn <andrew@lunn.ch>,
Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>,
Gregory Clement <gregory.clement@free-electrons.com>,
Russell King <linux@armlinux.org.uk>,
Vivien Didelot <vivien.didelot@savoirfairelinux.com>,
"David S. Miller" <davem@davemloft.net>,
linux-arm-kernel@lists.infradead.org (moderated list:ARM
SUB-ARCHITECTURES), linux-kernel@vger.kernel.org (open list),
gregkh@linuxfoundation.org
Subject: [PATCH net-next v2 10/10] ARM: orion: Register DSA switch as a MDIO device
Date: Wed, 11 Jan 2017 19:41:21 -0800 [thread overview]
Message-ID: <20170112034121.27697-11-f.fainelli@gmail.com> (raw)
In-Reply-To: <20170112034121.27697-1-f.fainelli@gmail.com>
Utilize the ability to pass board specific MDIO bus information towards a
particular MDIO device thus allowing us to provide the per-port switch layout
to the Marvell 88E6XXX switch driver.
Since we would end-up with conflicting registration paths, do not register the
"dsa" platform device anymore.
Note that the MDIO devices registered by code in net/dsa/dsa2.c does not
parse a dsa_platform_data, but directly take a dsa_chip_data (specific
to a single switch chip), so we update the different call sites to pass
this structure down to orion_ge00_switch_init().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm/mach-orion5x/common.c | 2 +-
arch/arm/mach-orion5x/common.h | 4 ++--
arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c | 7 +------
arch/arm/mach-orion5x/rd88f5181l-ge-setup.c | 7 +------
arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c | 7 +------
arch/arm/mach-orion5x/wnr854t-setup.c | 2 +-
arch/arm/mach-orion5x/wrt350n-v2-setup.c | 7 +------
arch/arm/plat-orion/common.c | 25 +++++++++++++++++++------
arch/arm/plat-orion/include/plat/common.h | 4 ++--
9 files changed, 29 insertions(+), 36 deletions(-)
diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c
index 04910764c385..83a7ec4c16d0 100644
--- a/arch/arm/mach-orion5x/common.c
+++ b/arch/arm/mach-orion5x/common.c
@@ -105,7 +105,7 @@ void __init orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data)
/*****************************************************************************
* Ethernet switch
****************************************************************************/
-void __init orion5x_eth_switch_init(struct dsa_platform_data *d)
+void __init orion5x_eth_switch_init(struct dsa_chip_data *d)
{
orion_ge00_switch_init(d);
}
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index 8a4115bd441d..efeffc6b4ebb 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -3,7 +3,7 @@
#include <linux/reboot.h>
-struct dsa_platform_data;
+struct dsa_chip_data;
struct mv643xx_eth_platform_data;
struct mv_sata_platform_data;
@@ -41,7 +41,7 @@ void orion5x_setup_wins(void);
void orion5x_ehci0_init(void);
void orion5x_ehci1_init(void);
void orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data);
-void orion5x_eth_switch_init(struct dsa_platform_data *d);
+void orion5x_eth_switch_init(struct dsa_chip_data *d);
void orion5x_i2c_init(void);
void orion5x_sata_init(struct mv_sata_platform_data *sata_data);
void orion5x_spi_init(void);
diff --git a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
index dccadf68ea2b..a3c1336d30c9 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
@@ -101,11 +101,6 @@ static struct dsa_chip_data rd88f5181l_fxo_switch_chip_data = {
.port_names[7] = "lan3",
};
-static struct dsa_platform_data __initdata rd88f5181l_fxo_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f5181l_fxo_switch_chip_data,
-};
-
static void __init rd88f5181l_fxo_init(void)
{
/*
@@ -120,7 +115,7 @@ static void __init rd88f5181l_fxo_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_fxo_eth_data);
- orion5x_eth_switch_init(&rd88f5181l_fxo_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f5181l_fxo_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
index affe5ec825de..252efe29bd1a 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
@@ -102,11 +102,6 @@ static struct dsa_chip_data rd88f5181l_ge_switch_chip_data = {
.port_names[7] = "lan3",
};
-static struct dsa_platform_data __initdata rd88f5181l_ge_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f5181l_ge_switch_chip_data,
-};
-
static struct i2c_board_info __initdata rd88f5181l_ge_i2c_rtc = {
I2C_BOARD_INFO("ds1338", 0x68),
};
@@ -125,7 +120,7 @@ static void __init rd88f5181l_ge_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_ge_eth_data);
- orion5x_eth_switch_init(&rd88f5181l_ge_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f5181l_ge_switch_chip_data);
orion5x_i2c_init();
orion5x_uart0_init();
diff --git a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
index 67ee8571b03c..f4f1dbe1d91d 100644
--- a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
@@ -40,11 +40,6 @@ static struct dsa_chip_data rd88f6183ap_ge_switch_chip_data = {
.port_names[5] = "cpu",
};
-static struct dsa_platform_data __initdata rd88f6183ap_ge_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f6183ap_ge_switch_chip_data,
-};
-
static struct mtd_partition rd88f6183ap_ge_partitions[] = {
{
.name = "kernel",
@@ -89,7 +84,7 @@ static void __init rd88f6183ap_ge_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f6183ap_ge_eth_data);
- orion5x_eth_switch_init(&rd88f6183ap_ge_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f6183ap_ge_switch_chip_data);
spi_register_board_info(rd88f6183ap_ge_spi_slave_info,
ARRAY_SIZE(rd88f6183ap_ge_spi_slave_info));
orion5x_spi_init();
diff --git a/arch/arm/mach-orion5x/wnr854t-setup.c b/arch/arm/mach-orion5x/wnr854t-setup.c
index 4dbcdbe1de7c..ac3376fc269f 100644
--- a/arch/arm/mach-orion5x/wnr854t-setup.c
+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
@@ -124,7 +124,7 @@ static void __init wnr854t_init(void)
* Configure peripherals.
*/
orion5x_eth_init(&wnr854t_eth_data);
- orion5x_eth_switch_init(&wnr854t_switch_plat_data);
+ orion5x_eth_switch_init(&wnr854t_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
index a6a8c4648d74..9250bb2e429c 100644
--- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
@@ -191,11 +191,6 @@ static struct dsa_chip_data wrt350n_v2_switch_chip_data = {
.port_names[7] = "lan4",
};
-static struct dsa_platform_data __initdata wrt350n_v2_switch_plat_data = {
- .nr_chips = 1,
- .chip = &wrt350n_v2_switch_chip_data,
-};
-
static void __init wrt350n_v2_init(void)
{
/*
@@ -210,7 +205,7 @@ static void __init wrt350n_v2_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&wrt350n_v2_eth_data);
- orion5x_eth_switch_init(&wrt350n_v2_switch_plat_data);
+ orion5x_eth_switch_init(&wrt350n_v2_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/plat-orion/common.c b/arch/arm/plat-orion/common.c
index 272f49b2c68f..989f3ccfcdc7 100644
--- a/arch/arm/plat-orion/common.c
+++ b/arch/arm/plat-orion/common.c
@@ -22,6 +22,7 @@
#include <linux/platform_data/dma-mv_xor.h>
#include <linux/platform_data/usb-ehci-orion.h>
#include <plat/common.h>
+#include <linux/phy.h>
/* Create a clkdev entry for a given device/clk */
void __init orion_clkdev_add(const char *con_id, const char *dev_id,
@@ -470,15 +471,27 @@ void __init orion_ge11_init(struct mv643xx_eth_platform_data *eth_data,
/*****************************************************************************
* Ethernet switch
****************************************************************************/
-void __init orion_ge00_switch_init(struct dsa_platform_data *d)
+static __initdata const char *orion_ge00_mvmdio_bus_name = "orion-mii";
+static __initdata struct mdio_board_info
+ orion_ge00_switch_board_info;
+
+void __init orion_ge00_switch_init(struct dsa_chip_data *d)
{
- int i;
+ struct mdio_board_info *bd;
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(d->port_names); i++)
+ if (!strcmp(d->port_names[i], "cpu"))
+ break;
- d->netdev = &orion_ge00.dev;
- for (i = 0; i < d->nr_chips; i++)
- d->chip[i].host_dev = &orion_ge_mvmdio.dev;
+ bd = &orion_ge00_switch_board_info;
+ bd->bus_id = orion_ge00_mvmdio_bus_name;
+ bd->mdio_addr = d->sw_addr;
+ d->netdev[i] = &orion_ge00.dev;
+ strcpy(bd->modalias, "mv88e6085");
+ bd->platform_data = d;
- platform_device_register_data(NULL, "dsa", 0, d, sizeof(d));
+ mdiobus_register_board_info(&orion_ge00_switch_board_info, 1);
}
/*****************************************************************************
diff --git a/arch/arm/plat-orion/include/plat/common.h b/arch/arm/plat-orion/include/plat/common.h
index 9347f3c58a6d..3647d3b33c20 100644
--- a/arch/arm/plat-orion/include/plat/common.h
+++ b/arch/arm/plat-orion/include/plat/common.h
@@ -12,7 +12,7 @@
#include <linux/mv643xx_eth.h>
#include <linux/platform_data/usb-ehci-orion.h>
-struct dsa_platform_data;
+struct dsa_chip_data;
struct mv_sata_platform_data;
void __init orion_uart0_init(void __iomem *membase,
@@ -57,7 +57,7 @@ void __init orion_ge11_init(struct mv643xx_eth_platform_data *eth_data,
unsigned long mapbase,
unsigned long irq);
-void __init orion_ge00_switch_init(struct dsa_platform_data *d);
+void __init orion_ge00_switch_init(struct dsa_chip_data *d);
void __init orion_i2c_init(unsigned long mapbase,
unsigned long irq,
--
2.9.3
next prev parent reply other threads:[~2017-01-12 3:41 UTC|newest]
Thread overview: 48+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-12 3:41 [PATCH net-next v2 00/10] net: dsa: Support for pdata in dsa2 Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` [PATCH net-next v2 01/10] net: dsa: Pass device pointer to dsa_register_switch Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` [PATCH net-next v2 02/10] net: dsa: Make most functions take a dsa_port argument Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` [PATCH net-next v2 03/10] net: dsa: Suffix function manipulating device_node with _dn Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` [PATCH net-next v2 04/10] net: dsa: Move ports assignment closer to error checking Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` [PATCH net-next v2 05/10] drivers: base: Add device_find_class() Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 21:21 ` David Miller
2017-01-12 21:21 ` David Miller
2017-01-12 22:50 ` Florian Fainelli
2017-01-12 22:50 ` Florian Fainelli
2017-01-13 4:16 ` David Miller
2017-01-13 4:16 ` David Miller
2017-01-13 10:55 ` David Laight
2017-01-13 10:55 ` David Laight
2017-01-14 19:01 ` Florian Fainelli
2017-01-14 19:01 ` Florian Fainelli
2017-01-12 3:41 ` [PATCH net-next v2 06/10] net: dsa: Migrate to device_find_class() Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` [PATCH net-next v2 07/10] net: Relocate dev_to_net_device() into core Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` [PATCH net-next v2 08/10] net: dsa: Add support for platform data Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-13 14:04 ` Andrew Lunn
2017-01-13 14:04 ` Andrew Lunn
2017-01-13 22:37 ` Florian Fainelli
2017-01-13 22:37 ` Florian Fainelli
2017-01-14 19:12 ` Florian Fainelli
2017-01-14 19:12 ` Florian Fainelli
2017-01-13 14:11 ` Andrew Lunn
2017-01-13 14:11 ` Andrew Lunn
2017-01-13 22:39 ` Florian Fainelli
2017-01-13 22:39 ` Florian Fainelli
2017-01-12 3:41 ` [PATCH net-next v2 09/10] net: phy: Allow pre-declaration of MDIO devices Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli
2017-01-12 3:41 ` Florian Fainelli [this message]
2017-01-12 3:41 ` [PATCH net-next v2 10/10] ARM: orion: Register DSA switch as a MDIO device Florian Fainelli
2017-01-13 2:34 ` [PATCH net-next v2 00/10] net: dsa: Support for pdata in dsa2 Vivien Didelot
2017-01-13 2:34 ` Vivien Didelot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170112034121.27697-11-f.fainelli@gmail.com \
--to=f.fainelli@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.