Re: [PATCH v3] ARM: dts: Add support for Liebherr's BK4 device (vf610 based)

From: Lukasz Majewski <lukma@denx.de>
To: Fabio Estevam <festevam@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>,
	"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
	<devicetree@vger.kernel.org>,
	Sascha Hauer <s.hauer@pengutronix.de>,
	linux-kernel <linux-kernel@vger.kernel.org>,
	Stefan Agner <stefan@agner.ch>, Rob Herring <robh+dt@kernel.org>,
	Sascha Hauer <kernel@pengutronix.de>,
	Fabio Estevam <fabio.estevam@nxp.com>,
	Shawn Guo <shawnguo@kernel.org>,
	"moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE"
	<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH v3] ARM: dts: Add support for Liebherr's BK4 device (vf610 based)
Date: Thu, 6 Dec 2018 09:22:55 +0100	[thread overview]
Message-ID: <20181206092255.2359f7e6@jawa> (raw)
In-Reply-To: <CAOMZO5BN5KJ+s6F9CJXQPX=Ta0Ow0PaV_AmFHYSDNr78jLjziQ@mail.gmail.com>

[-- Attachment #1.1: Type: text/plain, Size: 2015 bytes --]

On Wed, 5 Dec 2018 21:12:46 -0200
Fabio Estevam <festevam@gmail.com> wrote:

> Hi Lukasz/Rob,
> 
> On Tue, Oct 9, 2018 at 7:50 AM Lukasz Majewski <lukma@denx.de> wrote:
> 
> > +&dspi3 {
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&pinctrl_dspi3>;
> > +       bus-num = <3>;
> > +       status = "okay";
> > +       spi-slave;
> > +
> > +       slave@0 {
> > +               compatible = "lwn,bk4";
> > +               spi-max-frequency = <30000000>;
> > +               reg = <0>;
> > +       };
> > +};  
> 
> This is causing the following dtc warning in linux-next:
> 
>   DTC     arch/arm/boot/dts/vf610-bk4.dtb
> arch/arm/boot/dts/vfxxx.dtsi:550.24-563.6: Warning (spi_bus_bridge):
> /soc/aips-bus@40080000/spi@400ad000: incorrect #address-cells for SPI
> bus
>   also defined at arch/arm/boot/dts/vf610-bk4.dts:106.8-118.3
> arch/arm/boot/dts/vf610-bk4.dtb: Warning (spi_bus_reg): Failed
> prerequisite 'spi_bus_bridge'
> 
> If spi-slave property is removed the warning is gone.

The spi-slave has been added according to review suggestion:
https://lkml.org/lkml/2018/9/26/836

That is the way to handle "slave" SPI operation mode across the kernel. 

At the time of development - I've checked my NXP related patches with
W=1 passed to make. No warnings observed then.

> 
> Looking at drivers/spi/spi-fsl-dspi.c I don't see the "spi-slave"
> property being handled there.
> 
> Any ideas on how to fix this?

The *.dts file for Vybrid was sent and work on in parallel with the SPI
slave code implementation for Vybrid:

https://patchwork.kernel.org/patch/10680431/

Unfortunately, for the above patch I did not received any feedback
since mid September.

> 
> Thanks

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de

[-- Attachment #1.2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel