* [PATCH 0/2] ARM: dts: ls1021a: define and use external interrupt lines @ 2019-11-12 13:20 ` Rasmus Villemoes 0 siblings, 0 replies; 18+ messages in thread From: Rasmus Villemoes @ 2019-11-12 13:20 UTC (permalink / raw) To: Shawn Guo, Li Yang, Rob Herring, Mark Rutland, linux-arm-kernel, devicetree, linux-kernel Cc: Marc Zyngier, Vladimir Oltean, Rasmus Villemoes A device tree binding documentation as well as a driver implementing support for the external interrupt lines on the ls1021a has been merged into irqchip-next, so will very likely appear in v5.5. See 87cd38dfd9e6 dt/bindings: Add bindings for Layerscape external irqs 0dcd9f872769 irqchip: Add support for Layerscape external interrupt lines present in next-20191112. These patches simply add the extirq node to the ls1021a.dtsi and make use of it on the LS1021A-TSN board. I hope these can be picked up so they also land in v5.5, so we don't have to wait a full extra release cycle. Rasmus Villemoes (1): ARM: dts: ls1021a: add node describing external interrupt lines Vladimir Oltean (1): ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ arch/arm/boot/dts/ls1021a.dtsi | 19 +++++++++++++++++++ 2 files changed, 23 insertions(+) -- 2.23.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 0/2] ARM: dts: ls1021a: define and use external interrupt lines @ 2019-11-12 13:20 ` Rasmus Villemoes 0 siblings, 0 replies; 18+ messages in thread From: Rasmus Villemoes @ 2019-11-12 13:20 UTC (permalink / raw) To: Shawn Guo, Li Yang, Rob Herring, Mark Rutland, linux-arm-kernel, devicetree, linux-kernel Cc: Vladimir Oltean, Marc Zyngier, Rasmus Villemoes A device tree binding documentation as well as a driver implementing support for the external interrupt lines on the ls1021a has been merged into irqchip-next, so will very likely appear in v5.5. See 87cd38dfd9e6 dt/bindings: Add bindings for Layerscape external irqs 0dcd9f872769 irqchip: Add support for Layerscape external interrupt lines present in next-20191112. These patches simply add the extirq node to the ls1021a.dtsi and make use of it on the LS1021A-TSN board. I hope these can be picked up so they also land in v5.5, so we don't have to wait a full extra release cycle. Rasmus Villemoes (1): ARM: dts: ls1021a: add node describing external interrupt lines Vladimir Oltean (1): ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ arch/arm/boot/dts/ls1021a.dtsi | 19 +++++++++++++++++++ 2 files changed, 23 insertions(+) -- 2.23.0 ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 1/2] ARM: dts: ls1021a: add node describing external interrupt lines 2019-11-12 13:20 ` Rasmus Villemoes @ 2019-11-12 13:20 ` Rasmus Villemoes -1 siblings, 0 replies; 18+ messages in thread From: Rasmus Villemoes @ 2019-11-12 13:20 UTC (permalink / raw) To: Shawn Guo, Li Yang, Rob Herring, Mark Rutland Cc: devicetree, Marc Zyngier, Rasmus Villemoes, linux-kernel, Vladimir Oltean, linux-arm-kernel This adds a node describing the six external interrupt lines IRQ0-IRQ5 with configurable polarity. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> --- arch/arm/boot/dts/ls1021a.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi index 2f6977ada447..0855b1fe98e0 100644 --- a/arch/arm/boot/dts/ls1021a.dtsi +++ b/arch/arm/boot/dts/ls1021a.dtsi @@ -216,6 +216,25 @@ compatible = "fsl,ls1021a-scfg", "syscon"; reg = <0x0 0x1570000 0x0 0x10000>; big-endian; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x1570000 0x10000>; + + extirq: interrupt-controller@1ac { + compatible = "fsl,ls1021a-extirq"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0x1ac 4>; + interrupt-map = + <0 0 &gic GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <0xffffffff 0x0>; + }; }; crypto: crypto@1700000 { -- 2.23.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 1/2] ARM: dts: ls1021a: add node describing external interrupt lines @ 2019-11-12 13:20 ` Rasmus Villemoes 0 siblings, 0 replies; 18+ messages in thread From: Rasmus Villemoes @ 2019-11-12 13:20 UTC (permalink / raw) To: Shawn Guo, Li Yang, Rob Herring, Mark Rutland Cc: Vladimir Oltean, Marc Zyngier, Rasmus Villemoes, linux-arm-kernel, devicetree, linux-kernel This adds a node describing the six external interrupt lines IRQ0-IRQ5 with configurable polarity. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> --- arch/arm/boot/dts/ls1021a.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi index 2f6977ada447..0855b1fe98e0 100644 --- a/arch/arm/boot/dts/ls1021a.dtsi +++ b/arch/arm/boot/dts/ls1021a.dtsi @@ -216,6 +216,25 @@ compatible = "fsl,ls1021a-scfg", "syscon"; reg = <0x0 0x1570000 0x0 0x10000>; big-endian; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x1570000 0x10000>; + + extirq: interrupt-controller@1ac { + compatible = "fsl,ls1021a-extirq"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0x1ac 4>; + interrupt-map = + <0 0 &gic GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <0xffffffff 0x0>; + }; }; crypto: crypto@1700000 { -- 2.23.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs 2019-11-12 13:20 ` Rasmus Villemoes @ 2019-11-12 13:20 ` Rasmus Villemoes -1 siblings, 0 replies; 18+ messages in thread From: Rasmus Villemoes @ 2019-11-12 13:20 UTC (permalink / raw) To: Shawn Guo, Li Yang, Rob Herring, Mark Rutland Cc: devicetree, Marc Zyngier, Rasmus Villemoes, linux-kernel, Vladimir Oltean, linux-arm-kernel From: Vladimir Oltean <olteanv@gmail.com> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and eth1 have interrupt lines connected to the shared IRQ2_B LS1021A pin. Switching to interrupts offloads the PHY library from the task of polling the MDIO status and AN registers (1, 4, 5) every second. Unfortunately, the BCM5464R quad PHY connected to the switch does not appear to have an interrupt line routed to the SoC. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> --- arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/ls1021a-tsn.dts index 5b7689094b70..135d36461af4 100644 --- a/arch/arm/boot/dts/ls1021a-tsn.dts +++ b/arch/arm/boot/dts/ls1021a-tsn.dts @@ -203,11 +203,15 @@ /* AR8031 */ sgmii_phy1: ethernet-phy@1 { reg = <0x1>; + /* SGMII1_PHY_INT_B: connected to IRQ2, active low */ + interrupts-extended = <&extirq 2 IRQ_TYPE_EDGE_FALLING>; }; /* AR8031 */ sgmii_phy2: ethernet-phy@2 { reg = <0x2>; + /* SGMII2_PHY_INT_B: connected to IRQ2, active low */ + interrupts-extended = <&extirq 2 IRQ_TYPE_EDGE_FALLING>; }; /* BCM5464 quad PHY */ -- 2.23.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs @ 2019-11-12 13:20 ` Rasmus Villemoes 0 siblings, 0 replies; 18+ messages in thread From: Rasmus Villemoes @ 2019-11-12 13:20 UTC (permalink / raw) To: Shawn Guo, Li Yang, Rob Herring, Mark Rutland Cc: Vladimir Oltean, Marc Zyngier, Rasmus Villemoes, linux-arm-kernel, devicetree, linux-kernel From: Vladimir Oltean <olteanv@gmail.com> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and eth1 have interrupt lines connected to the shared IRQ2_B LS1021A pin. Switching to interrupts offloads the PHY library from the task of polling the MDIO status and AN registers (1, 4, 5) every second. Unfortunately, the BCM5464R quad PHY connected to the switch does not appear to have an interrupt line routed to the SoC. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> --- arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/ls1021a-tsn.dts index 5b7689094b70..135d36461af4 100644 --- a/arch/arm/boot/dts/ls1021a-tsn.dts +++ b/arch/arm/boot/dts/ls1021a-tsn.dts @@ -203,11 +203,15 @@ /* AR8031 */ sgmii_phy1: ethernet-phy@1 { reg = <0x1>; + /* SGMII1_PHY_INT_B: connected to IRQ2, active low */ + interrupts-extended = <&extirq 2 IRQ_TYPE_EDGE_FALLING>; }; /* AR8031 */ sgmii_phy2: ethernet-phy@2 { reg = <0x2>; + /* SGMII2_PHY_INT_B: connected to IRQ2, active low */ + interrupts-extended = <&extirq 2 IRQ_TYPE_EDGE_FALLING>; }; /* BCM5464 quad PHY */ -- 2.23.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs 2019-11-12 13:20 ` Rasmus Villemoes @ 2019-11-12 13:44 ` Vladimir Oltean -1 siblings, 0 replies; 18+ messages in thread From: Vladimir Oltean @ 2019-11-12 13:44 UTC (permalink / raw) To: Rasmus Villemoes Cc: Mark Rutland, devicetree, Andrew Lunn, Marc Zyngier, lkml, Li Yang, Rob Herring, netdev, Shawn Guo, linux-arm-kernel On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes <linux@rasmusvillemoes.dk> wrote: > > From: Vladimir Oltean <olteanv@gmail.com> > > On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and eth1 > have interrupt lines connected to the shared IRQ2_B LS1021A pin. > > Switching to interrupts offloads the PHY library from the task of > polling the MDIO status and AN registers (1, 4, 5) every second. > > Unfortunately, the BCM5464R quad PHY connected to the switch does not > appear to have an interrupt line routed to the SoC. > > Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> > --- > arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ > 1 file changed, 4 insertions(+) > > diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/ls1021a-tsn.dts > index 5b7689094b70..135d36461af4 100644 > --- a/arch/arm/boot/dts/ls1021a-tsn.dts > +++ b/arch/arm/boot/dts/ls1021a-tsn.dts > @@ -203,11 +203,15 @@ > /* AR8031 */ > sgmii_phy1: ethernet-phy@1 { > reg = <0x1>; > + /* SGMII1_PHY_INT_B: connected to IRQ2, active low */ > + interrupts-extended = <&extirq 2 IRQ_TYPE_EDGE_FALLING>; > }; > > /* AR8031 */ > sgmii_phy2: ethernet-phy@2 { > reg = <0x2>; > + /* SGMII2_PHY_INT_B: connected to IRQ2, active low */ > + interrupts-extended = <&extirq 2 IRQ_TYPE_EDGE_FALLING>; > }; > > /* BCM5464 quad PHY */ > -- > 2.23.0 > +netdev and Andrew for this patch, since the interrupt polarity caught his attention in v1. _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs @ 2019-11-12 13:44 ` Vladimir Oltean 0 siblings, 0 replies; 18+ messages in thread From: Vladimir Oltean @ 2019-11-12 13:44 UTC (permalink / raw) To: Rasmus Villemoes Cc: Shawn Guo, Li Yang, Rob Herring, Mark Rutland, Marc Zyngier, linux-arm-kernel, devicetree, lkml, netdev, Andrew Lunn On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes <linux@rasmusvillemoes.dk> wrote: > > From: Vladimir Oltean <olteanv@gmail.com> > > On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and eth1 > have interrupt lines connected to the shared IRQ2_B LS1021A pin. > > Switching to interrupts offloads the PHY library from the task of > polling the MDIO status and AN registers (1, 4, 5) every second. > > Unfortunately, the BCM5464R quad PHY connected to the switch does not > appear to have an interrupt line routed to the SoC. > > Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> > --- > arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ > 1 file changed, 4 insertions(+) > > diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/ls1021a-tsn.dts > index 5b7689094b70..135d36461af4 100644 > --- a/arch/arm/boot/dts/ls1021a-tsn.dts > +++ b/arch/arm/boot/dts/ls1021a-tsn.dts > @@ -203,11 +203,15 @@ > /* AR8031 */ > sgmii_phy1: ethernet-phy@1 { > reg = <0x1>; > + /* SGMII1_PHY_INT_B: connected to IRQ2, active low */ > + interrupts-extended = <&extirq 2 IRQ_TYPE_EDGE_FALLING>; > }; > > /* AR8031 */ > sgmii_phy2: ethernet-phy@2 { > reg = <0x2>; > + /* SGMII2_PHY_INT_B: connected to IRQ2, active low */ > + interrupts-extended = <&extirq 2 IRQ_TYPE_EDGE_FALLING>; > }; > > /* BCM5464 quad PHY */ > -- > 2.23.0 > +netdev and Andrew for this patch, since the interrupt polarity caught his attention in v1. ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs 2019-11-12 13:44 ` Vladimir Oltean @ 2019-11-12 13:49 ` Marc Zyngier -1 siblings, 0 replies; 18+ messages in thread From: Marc Zyngier @ 2019-11-12 13:49 UTC (permalink / raw) To: Vladimir Oltean Cc: Mark Rutland, devicetree, Andrew Lunn, netdev, Rasmus Villemoes, lkml, Li Yang, Rob Herring, Shawn Guo, linux-arm-kernel On 2019-11-12 14:53, Vladimir Oltean wrote: > On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes > <linux@rasmusvillemoes.dk> wrote: >> >> From: Vladimir Oltean <olteanv@gmail.com> >> >> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and >> eth1 >> have interrupt lines connected to the shared IRQ2_B LS1021A pin. >> >> Switching to interrupts offloads the PHY library from the task of >> polling the MDIO status and AN registers (1, 4, 5) every second. >> >> Unfortunately, the BCM5464R quad PHY connected to the switch does >> not >> appear to have an interrupt line routed to the SoC. >> >> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> >> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> >> --- >> arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ >> 1 file changed, 4 insertions(+) >> >> diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts >> b/arch/arm/boot/dts/ls1021a-tsn.dts >> index 5b7689094b70..135d36461af4 100644 >> --- a/arch/arm/boot/dts/ls1021a-tsn.dts >> +++ b/arch/arm/boot/dts/ls1021a-tsn.dts >> @@ -203,11 +203,15 @@ >> /* AR8031 */ >> sgmii_phy1: ethernet-phy@1 { >> reg = <0x1>; >> + /* SGMII1_PHY_INT_B: connected to IRQ2, active low >> */ >> + interrupts-extended = <&extirq 2 >> IRQ_TYPE_EDGE_FALLING>; >> }; >> >> /* AR8031 */ >> sgmii_phy2: ethernet-phy@2 { >> reg = <0x2>; >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active low >> */ >> + interrupts-extended = <&extirq 2 >> IRQ_TYPE_EDGE_FALLING>; >> }; >> >> /* BCM5464 quad PHY */ >> -- >> 2.23.0 >> > > +netdev and Andrew for this patch, since the interrupt polarity > caught > his attention in v1. Certainly, the comments and the interrupt specifier do not match. Which one is true? M. -- Jazz is not dead. It just smells funny... _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs @ 2019-11-12 13:49 ` Marc Zyngier 0 siblings, 0 replies; 18+ messages in thread From: Marc Zyngier @ 2019-11-12 13:49 UTC (permalink / raw) To: Vladimir Oltean Cc: Rasmus Villemoes, Shawn Guo, Li Yang, Rob Herring, Mark Rutland, linux-arm-kernel, devicetree, lkml, netdev, Andrew Lunn On 2019-11-12 14:53, Vladimir Oltean wrote: > On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes > <linux@rasmusvillemoes.dk> wrote: >> >> From: Vladimir Oltean <olteanv@gmail.com> >> >> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and >> eth1 >> have interrupt lines connected to the shared IRQ2_B LS1021A pin. >> >> Switching to interrupts offloads the PHY library from the task of >> polling the MDIO status and AN registers (1, 4, 5) every second. >> >> Unfortunately, the BCM5464R quad PHY connected to the switch does >> not >> appear to have an interrupt line routed to the SoC. >> >> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> >> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> >> --- >> arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ >> 1 file changed, 4 insertions(+) >> >> diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts >> b/arch/arm/boot/dts/ls1021a-tsn.dts >> index 5b7689094b70..135d36461af4 100644 >> --- a/arch/arm/boot/dts/ls1021a-tsn.dts >> +++ b/arch/arm/boot/dts/ls1021a-tsn.dts >> @@ -203,11 +203,15 @@ >> /* AR8031 */ >> sgmii_phy1: ethernet-phy@1 { >> reg = <0x1>; >> + /* SGMII1_PHY_INT_B: connected to IRQ2, active low >> */ >> + interrupts-extended = <&extirq 2 >> IRQ_TYPE_EDGE_FALLING>; >> }; >> >> /* AR8031 */ >> sgmii_phy2: ethernet-phy@2 { >> reg = <0x2>; >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active low >> */ >> + interrupts-extended = <&extirq 2 >> IRQ_TYPE_EDGE_FALLING>; >> }; >> >> /* BCM5464 quad PHY */ >> -- >> 2.23.0 >> > > +netdev and Andrew for this patch, since the interrupt polarity > caught > his attention in v1. Certainly, the comments and the interrupt specifier do not match. Which one is true? M. -- Jazz is not dead. It just smells funny... ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs 2019-11-12 13:49 ` Marc Zyngier @ 2019-11-12 13:53 ` Vladimir Oltean -1 siblings, 0 replies; 18+ messages in thread From: Vladimir Oltean @ 2019-11-12 13:53 UTC (permalink / raw) To: Marc Zyngier Cc: Mark Rutland, devicetree, Andrew Lunn, netdev, Rasmus Villemoes, lkml, Li Yang, Rob Herring, Shawn Guo, linux-arm-kernel On Tue, 12 Nov 2019 at 15:49, Marc Zyngier <maz@kernel.org> wrote: > > On 2019-11-12 14:53, Vladimir Oltean wrote: > > On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes > > <linux@rasmusvillemoes.dk> wrote: > >> > >> From: Vladimir Oltean <olteanv@gmail.com> > >> > >> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and > >> eth1 > >> have interrupt lines connected to the shared IRQ2_B LS1021A pin. > >> > >> Switching to interrupts offloads the PHY library from the task of > >> polling the MDIO status and AN registers (1, 4, 5) every second. > >> > >> Unfortunately, the BCM5464R quad PHY connected to the switch does > >> not > >> appear to have an interrupt line routed to the SoC. > >> > >> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > >> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> > >> --- > >> arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ > >> 1 file changed, 4 insertions(+) > >> > >> diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts > >> b/arch/arm/boot/dts/ls1021a-tsn.dts > >> index 5b7689094b70..135d36461af4 100644 > >> --- a/arch/arm/boot/dts/ls1021a-tsn.dts > >> +++ b/arch/arm/boot/dts/ls1021a-tsn.dts > >> @@ -203,11 +203,15 @@ > >> /* AR8031 */ > >> sgmii_phy1: ethernet-phy@1 { > >> reg = <0x1>; > >> + /* SGMII1_PHY_INT_B: connected to IRQ2, active low > >> */ > >> + interrupts-extended = <&extirq 2 > >> IRQ_TYPE_EDGE_FALLING>; > >> }; > >> > >> /* AR8031 */ > >> sgmii_phy2: ethernet-phy@2 { > >> reg = <0x2>; > >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active low > >> */ > >> + interrupts-extended = <&extirq 2 > >> IRQ_TYPE_EDGE_FALLING>; > >> }; > >> > >> /* BCM5464 quad PHY */ > >> -- > >> 2.23.0 > >> > > > > +netdev and Andrew for this patch, since the interrupt polarity > > caught > > his attention in v1. > > Certainly, the comments and the interrupt specifier do not match. > Which one is true? > > M. > -- > Jazz is not dead. It just smells funny... The interrupt specifier certainly works. So that points to an issue with the description. What do you mean, exactly? Does "active low" mean "level-triggered"? How would you have described this? _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs @ 2019-11-12 13:53 ` Vladimir Oltean 0 siblings, 0 replies; 18+ messages in thread From: Vladimir Oltean @ 2019-11-12 13:53 UTC (permalink / raw) To: Marc Zyngier Cc: Rasmus Villemoes, Shawn Guo, Li Yang, Rob Herring, Mark Rutland, linux-arm-kernel, devicetree, lkml, netdev, Andrew Lunn On Tue, 12 Nov 2019 at 15:49, Marc Zyngier <maz@kernel.org> wrote: > > On 2019-11-12 14:53, Vladimir Oltean wrote: > > On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes > > <linux@rasmusvillemoes.dk> wrote: > >> > >> From: Vladimir Oltean <olteanv@gmail.com> > >> > >> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and > >> eth1 > >> have interrupt lines connected to the shared IRQ2_B LS1021A pin. > >> > >> Switching to interrupts offloads the PHY library from the task of > >> polling the MDIO status and AN registers (1, 4, 5) every second. > >> > >> Unfortunately, the BCM5464R quad PHY connected to the switch does > >> not > >> appear to have an interrupt line routed to the SoC. > >> > >> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > >> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> > >> --- > >> arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ > >> 1 file changed, 4 insertions(+) > >> > >> diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts > >> b/arch/arm/boot/dts/ls1021a-tsn.dts > >> index 5b7689094b70..135d36461af4 100644 > >> --- a/arch/arm/boot/dts/ls1021a-tsn.dts > >> +++ b/arch/arm/boot/dts/ls1021a-tsn.dts > >> @@ -203,11 +203,15 @@ > >> /* AR8031 */ > >> sgmii_phy1: ethernet-phy@1 { > >> reg = <0x1>; > >> + /* SGMII1_PHY_INT_B: connected to IRQ2, active low > >> */ > >> + interrupts-extended = <&extirq 2 > >> IRQ_TYPE_EDGE_FALLING>; > >> }; > >> > >> /* AR8031 */ > >> sgmii_phy2: ethernet-phy@2 { > >> reg = <0x2>; > >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active low > >> */ > >> + interrupts-extended = <&extirq 2 > >> IRQ_TYPE_EDGE_FALLING>; > >> }; > >> > >> /* BCM5464 quad PHY */ > >> -- > >> 2.23.0 > >> > > > > +netdev and Andrew for this patch, since the interrupt polarity > > caught > > his attention in v1. > > Certainly, the comments and the interrupt specifier do not match. > Which one is true? > > M. > -- > Jazz is not dead. It just smells funny... The interrupt specifier certainly works. So that points to an issue with the description. What do you mean, exactly? Does "active low" mean "level-triggered"? How would you have described this? ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs 2019-11-12 13:53 ` Vladimir Oltean @ 2019-11-12 14:01 ` Andrew Lunn -1 siblings, 0 replies; 18+ messages in thread From: Andrew Lunn @ 2019-11-12 14:01 UTC (permalink / raw) To: Vladimir Oltean Cc: Mark Rutland, devicetree, Marc Zyngier, Rasmus Villemoes, lkml, Li Yang, Rob Herring, netdev, Shawn Guo, linux-arm-kernel > > >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active low > > >> */ > > >> + interrupts-extended = <&extirq 2 > > >> IRQ_TYPE_EDGE_FALLING>; > The interrupt specifier certainly works. So that points to an issue > with the description. What do you mean, exactly? Does "active low" > mean "level-triggered"? How would you have described this? I would expect IRQ_TYPE_ACTIVE_LOW, or whatever it is called. Since this is a shared interrupt, going on the edge i think opens up a race condition and interrupts can be missed. Andrew _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs @ 2019-11-12 14:01 ` Andrew Lunn 0 siblings, 0 replies; 18+ messages in thread From: Andrew Lunn @ 2019-11-12 14:01 UTC (permalink / raw) To: Vladimir Oltean Cc: Marc Zyngier, Rasmus Villemoes, Shawn Guo, Li Yang, Rob Herring, Mark Rutland, linux-arm-kernel, devicetree, lkml, netdev > > >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active low > > >> */ > > >> + interrupts-extended = <&extirq 2 > > >> IRQ_TYPE_EDGE_FALLING>; > The interrupt specifier certainly works. So that points to an issue > with the description. What do you mean, exactly? Does "active low" > mean "level-triggered"? How would you have described this? I would expect IRQ_TYPE_ACTIVE_LOW, or whatever it is called. Since this is a shared interrupt, going on the edge i think opens up a race condition and interrupts can be missed. Andrew ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs 2019-11-12 13:53 ` Vladimir Oltean @ 2019-11-12 14:04 ` Marc Zyngier -1 siblings, 0 replies; 18+ messages in thread From: Marc Zyngier @ 2019-11-12 14:04 UTC (permalink / raw) To: Vladimir Oltean Cc: Mark Rutland, devicetree, Andrew Lunn, netdev, Rasmus Villemoes, lkml, Li Yang, Rob Herring, Shawn Guo, linux-arm-kernel On 2019-11-12 15:03, Vladimir Oltean wrote: > On Tue, 12 Nov 2019 at 15:49, Marc Zyngier <maz@kernel.org> wrote: >> >> On 2019-11-12 14:53, Vladimir Oltean wrote: >> > On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes >> > <linux@rasmusvillemoes.dk> wrote: >> >> >> >> From: Vladimir Oltean <olteanv@gmail.com> >> >> >> >> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and >> >> eth1 >> >> have interrupt lines connected to the shared IRQ2_B LS1021A pin. >> >> >> >> Switching to interrupts offloads the PHY library from the task of >> >> polling the MDIO status and AN registers (1, 4, 5) every second. >> >> >> >> Unfortunately, the BCM5464R quad PHY connected to the switch does >> >> not >> >> appear to have an interrupt line routed to the SoC. >> >> >> >> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> >> >> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> >> >> --- >> >> arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ >> >> 1 file changed, 4 insertions(+) >> >> >> >> diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts >> >> b/arch/arm/boot/dts/ls1021a-tsn.dts >> >> index 5b7689094b70..135d36461af4 100644 >> >> --- a/arch/arm/boot/dts/ls1021a-tsn.dts >> >> +++ b/arch/arm/boot/dts/ls1021a-tsn.dts >> >> @@ -203,11 +203,15 @@ >> >> /* AR8031 */ >> >> sgmii_phy1: ethernet-phy@1 { >> >> reg = <0x1>; >> >> + /* SGMII1_PHY_INT_B: connected to IRQ2, active >> low >> >> */ >> >> + interrupts-extended = <&extirq 2 >> >> IRQ_TYPE_EDGE_FALLING>; >> >> }; >> >> >> >> /* AR8031 */ >> >> sgmii_phy2: ethernet-phy@2 { >> >> reg = <0x2>; >> >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active >> low >> >> */ >> >> + interrupts-extended = <&extirq 2 >> >> IRQ_TYPE_EDGE_FALLING>; >> >> }; >> >> >> >> /* BCM5464 quad PHY */ >> >> -- >> >> 2.23.0 >> >> >> > >> > +netdev and Andrew for this patch, since the interrupt polarity >> > caught >> > his attention in v1. >> >> Certainly, the comments and the interrupt specifier do not match. >> Which one is true? >> >> M. >> -- >> Jazz is not dead. It just smells funny... > > The interrupt specifier certainly works. So that points to an issue > with the description. What do you mean, exactly? Does "active low" > mean "level-triggered"? How would you have described this? Active Low definitely implies level triggered. And if that's how it is described in the TRM, than the interrupt specifier is wrong, and just *seem to work* because the level goes back to high between two interrupts. Also, shared *edge* interrupts do not work, full stop. So I'm pretty convinced that what you have here is just wrong. M. -- Jazz is not dead. It just smells funny... _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs @ 2019-11-12 14:04 ` Marc Zyngier 0 siblings, 0 replies; 18+ messages in thread From: Marc Zyngier @ 2019-11-12 14:04 UTC (permalink / raw) To: Vladimir Oltean Cc: Rasmus Villemoes, Shawn Guo, Li Yang, Rob Herring, Mark Rutland, linux-arm-kernel, devicetree, lkml, netdev, Andrew Lunn On 2019-11-12 15:03, Vladimir Oltean wrote: > On Tue, 12 Nov 2019 at 15:49, Marc Zyngier <maz@kernel.org> wrote: >> >> On 2019-11-12 14:53, Vladimir Oltean wrote: >> > On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes >> > <linux@rasmusvillemoes.dk> wrote: >> >> >> >> From: Vladimir Oltean <olteanv@gmail.com> >> >> >> >> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and >> >> eth1 >> >> have interrupt lines connected to the shared IRQ2_B LS1021A pin. >> >> >> >> Switching to interrupts offloads the PHY library from the task of >> >> polling the MDIO status and AN registers (1, 4, 5) every second. >> >> >> >> Unfortunately, the BCM5464R quad PHY connected to the switch does >> >> not >> >> appear to have an interrupt line routed to the SoC. >> >> >> >> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> >> >> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> >> >> --- >> >> arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ >> >> 1 file changed, 4 insertions(+) >> >> >> >> diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts >> >> b/arch/arm/boot/dts/ls1021a-tsn.dts >> >> index 5b7689094b70..135d36461af4 100644 >> >> --- a/arch/arm/boot/dts/ls1021a-tsn.dts >> >> +++ b/arch/arm/boot/dts/ls1021a-tsn.dts >> >> @@ -203,11 +203,15 @@ >> >> /* AR8031 */ >> >> sgmii_phy1: ethernet-phy@1 { >> >> reg = <0x1>; >> >> + /* SGMII1_PHY_INT_B: connected to IRQ2, active >> low >> >> */ >> >> + interrupts-extended = <&extirq 2 >> >> IRQ_TYPE_EDGE_FALLING>; >> >> }; >> >> >> >> /* AR8031 */ >> >> sgmii_phy2: ethernet-phy@2 { >> >> reg = <0x2>; >> >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active >> low >> >> */ >> >> + interrupts-extended = <&extirq 2 >> >> IRQ_TYPE_EDGE_FALLING>; >> >> }; >> >> >> >> /* BCM5464 quad PHY */ >> >> -- >> >> 2.23.0 >> >> >> > >> > +netdev and Andrew for this patch, since the interrupt polarity >> > caught >> > his attention in v1. >> >> Certainly, the comments and the interrupt specifier do not match. >> Which one is true? >> >> M. >> -- >> Jazz is not dead. It just smells funny... > > The interrupt specifier certainly works. So that points to an issue > with the description. What do you mean, exactly? Does "active low" > mean "level-triggered"? How would you have described this? Active Low definitely implies level triggered. And if that's how it is described in the TRM, than the interrupt specifier is wrong, and just *seem to work* because the level goes back to high between two interrupts. Also, shared *edge* interrupts do not work, full stop. So I'm pretty convinced that what you have here is just wrong. M. -- Jazz is not dead. It just smells funny... ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs 2019-11-12 14:04 ` Marc Zyngier @ 2019-11-12 14:12 ` Vladimir Oltean -1 siblings, 0 replies; 18+ messages in thread From: Vladimir Oltean @ 2019-11-12 14:12 UTC (permalink / raw) To: Marc Zyngier Cc: Mark Rutland, devicetree, Andrew Lunn, netdev, Rasmus Villemoes, lkml, Li Yang, Rob Herring, Shawn Guo, linux-arm-kernel On Tue, 12 Nov 2019 at 16:04, Marc Zyngier <maz@kernel.org> wrote: > > On 2019-11-12 15:03, Vladimir Oltean wrote: > > On Tue, 12 Nov 2019 at 15:49, Marc Zyngier <maz@kernel.org> wrote: > >> > >> On 2019-11-12 14:53, Vladimir Oltean wrote: > >> > On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes > >> > <linux@rasmusvillemoes.dk> wrote: > >> >> > >> >> From: Vladimir Oltean <olteanv@gmail.com> > >> >> > >> >> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and > >> >> eth1 > >> >> have interrupt lines connected to the shared IRQ2_B LS1021A pin. > >> >> > >> >> Switching to interrupts offloads the PHY library from the task of > >> >> polling the MDIO status and AN registers (1, 4, 5) every second. > >> >> > >> >> Unfortunately, the BCM5464R quad PHY connected to the switch does > >> >> not > >> >> appear to have an interrupt line routed to the SoC. > >> >> > >> >> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > >> >> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> > >> >> --- > >> >> arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ > >> >> 1 file changed, 4 insertions(+) > >> >> > >> >> diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts > >> >> b/arch/arm/boot/dts/ls1021a-tsn.dts > >> >> index 5b7689094b70..135d36461af4 100644 > >> >> --- a/arch/arm/boot/dts/ls1021a-tsn.dts > >> >> +++ b/arch/arm/boot/dts/ls1021a-tsn.dts > >> >> @@ -203,11 +203,15 @@ > >> >> /* AR8031 */ > >> >> sgmii_phy1: ethernet-phy@1 { > >> >> reg = <0x1>; > >> >> + /* SGMII1_PHY_INT_B: connected to IRQ2, active > >> low > >> >> */ > >> >> + interrupts-extended = <&extirq 2 > >> >> IRQ_TYPE_EDGE_FALLING>; > >> >> }; > >> >> > >> >> /* AR8031 */ > >> >> sgmii_phy2: ethernet-phy@2 { > >> >> reg = <0x2>; > >> >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active > >> low > >> >> */ > >> >> + interrupts-extended = <&extirq 2 > >> >> IRQ_TYPE_EDGE_FALLING>; > >> >> }; > >> >> > >> >> /* BCM5464 quad PHY */ > >> >> -- > >> >> 2.23.0 > >> >> > >> > > >> > +netdev and Andrew for this patch, since the interrupt polarity > >> > caught > >> > his attention in v1. > >> > >> Certainly, the comments and the interrupt specifier do not match. > >> Which one is true? > >> > >> M. > >> -- > >> Jazz is not dead. It just smells funny... > > > > The interrupt specifier certainly works. So that points to an issue > > with the description. What do you mean, exactly? Does "active low" > > mean "level-triggered"? How would you have described this? > > Active Low definitely implies level triggered. And if that's how it > is described in the TRM, than the interrupt specifier is wrong, and > just *seem to work* because the level goes back to high between two > interrupts. > > Also, shared *edge* interrupts do not work, full stop. So I'm pretty > convinced that what you have here is just wrong. > > M. > -- > Jazz is not dead. It just smells funny... Ok, I've tested both interrupts with IRQ_TYPE_LEVEL_LOW and they still work. I'll let Rasmus re-send if there is no trouble with the dtsi patch. Sorry for the trouble and thanks for teaching me something new. Cheers, -Vladimir _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs @ 2019-11-12 14:12 ` Vladimir Oltean 0 siblings, 0 replies; 18+ messages in thread From: Vladimir Oltean @ 2019-11-12 14:12 UTC (permalink / raw) To: Marc Zyngier Cc: Rasmus Villemoes, Shawn Guo, Li Yang, Rob Herring, Mark Rutland, linux-arm-kernel, devicetree, lkml, netdev, Andrew Lunn On Tue, 12 Nov 2019 at 16:04, Marc Zyngier <maz@kernel.org> wrote: > > On 2019-11-12 15:03, Vladimir Oltean wrote: > > On Tue, 12 Nov 2019 at 15:49, Marc Zyngier <maz@kernel.org> wrote: > >> > >> On 2019-11-12 14:53, Vladimir Oltean wrote: > >> > On Tue, 12 Nov 2019 at 15:20, Rasmus Villemoes > >> > <linux@rasmusvillemoes.dk> wrote: > >> >> > >> >> From: Vladimir Oltean <olteanv@gmail.com> > >> >> > >> >> On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and > >> >> eth1 > >> >> have interrupt lines connected to the shared IRQ2_B LS1021A pin. > >> >> > >> >> Switching to interrupts offloads the PHY library from the task of > >> >> polling the MDIO status and AN registers (1, 4, 5) every second. > >> >> > >> >> Unfortunately, the BCM5464R quad PHY connected to the switch does > >> >> not > >> >> appear to have an interrupt line routed to the SoC. > >> >> > >> >> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > >> >> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> > >> >> --- > >> >> arch/arm/boot/dts/ls1021a-tsn.dts | 4 ++++ > >> >> 1 file changed, 4 insertions(+) > >> >> > >> >> diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts > >> >> b/arch/arm/boot/dts/ls1021a-tsn.dts > >> >> index 5b7689094b70..135d36461af4 100644 > >> >> --- a/arch/arm/boot/dts/ls1021a-tsn.dts > >> >> +++ b/arch/arm/boot/dts/ls1021a-tsn.dts > >> >> @@ -203,11 +203,15 @@ > >> >> /* AR8031 */ > >> >> sgmii_phy1: ethernet-phy@1 { > >> >> reg = <0x1>; > >> >> + /* SGMII1_PHY_INT_B: connected to IRQ2, active > >> low > >> >> */ > >> >> + interrupts-extended = <&extirq 2 > >> >> IRQ_TYPE_EDGE_FALLING>; > >> >> }; > >> >> > >> >> /* AR8031 */ > >> >> sgmii_phy2: ethernet-phy@2 { > >> >> reg = <0x2>; > >> >> + /* SGMII2_PHY_INT_B: connected to IRQ2, active > >> low > >> >> */ > >> >> + interrupts-extended = <&extirq 2 > >> >> IRQ_TYPE_EDGE_FALLING>; > >> >> }; > >> >> > >> >> /* BCM5464 quad PHY */ > >> >> -- > >> >> 2.23.0 > >> >> > >> > > >> > +netdev and Andrew for this patch, since the interrupt polarity > >> > caught > >> > his attention in v1. > >> > >> Certainly, the comments and the interrupt specifier do not match. > >> Which one is true? > >> > >> M. > >> -- > >> Jazz is not dead. It just smells funny... > > > > The interrupt specifier certainly works. So that points to an issue > > with the description. What do you mean, exactly? Does "active low" > > mean "level-triggered"? How would you have described this? > > Active Low definitely implies level triggered. And if that's how it > is described in the TRM, than the interrupt specifier is wrong, and > just *seem to work* because the level goes back to high between two > interrupts. > > Also, shared *edge* interrupts do not work, full stop. So I'm pretty > convinced that what you have here is just wrong. > > M. > -- > Jazz is not dead. It just smells funny... Ok, I've tested both interrupts with IRQ_TYPE_LEVEL_LOW and they still work. I'll let Rasmus re-send if there is no trouble with the dtsi patch. Sorry for the trouble and thanks for teaching me something new. Cheers, -Vladimir ^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2019-11-12 14:12 UTC | newest] Thread overview: 18+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2019-11-12 13:20 [PATCH 0/2] ARM: dts: ls1021a: define and use external interrupt lines Rasmus Villemoes 2019-11-12 13:20 ` Rasmus Villemoes 2019-11-12 13:20 ` [PATCH 1/2] ARM: dts: ls1021a: add node describing " Rasmus Villemoes 2019-11-12 13:20 ` Rasmus Villemoes 2019-11-12 13:20 ` [PATCH 2/2] ARM: dts: ls1021a-tsn: Use interrupts for the SGMII PHYs Rasmus Villemoes 2019-11-12 13:20 ` Rasmus Villemoes 2019-11-12 13:44 ` Vladimir Oltean 2019-11-12 13:44 ` Vladimir Oltean 2019-11-12 13:49 ` Marc Zyngier 2019-11-12 13:49 ` Marc Zyngier 2019-11-12 13:53 ` Vladimir Oltean 2019-11-12 13:53 ` Vladimir Oltean 2019-11-12 14:01 ` Andrew Lunn 2019-11-12 14:01 ` Andrew Lunn 2019-11-12 14:04 ` Marc Zyngier 2019-11-12 14:04 ` Marc Zyngier 2019-11-12 14:12 ` Vladimir Oltean 2019-11-12 14:12 ` Vladimir Oltean
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.