[PATCH v3 00/14] ARM: dts: aspeed: Add IBM P11 BMC Boards

[PATCH v3 00/14] ARM: dts: aspeed: Add IBM P11 BMC Boards

[Eddie James]

Add the Blueridge and Fuji BMC systems. Document many missing FSI related
properties, and fix existing warnings.

Changes since v2:
 - Split up the DTS patches
 - Add documentation patches

Eddie James (14):
  dt-bindings: spi: Document the IBM Power SPI controller
  dt-bindings: fsi: fsi2spi: Document SPI controller child nodes
  dt-bindings: fsi: Document the FSI2PIB engine
  dt-bindings: fsi: p9-occ: Switch to yaml format
  dt-bindings: fsi: Document the IBM SBEFIFO engine
  dt-bindings: fsi: Document the FSI controller common properties
  dt-bindings: fsi: ibm,i2cr-fsi-master: Reference common FSI controller
  dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format
  dt-bindings: fsi: Document the FSI Hub Controller
  dt-bindings: i2c: i2c-fsi: Switch to yaml format
  dt-bindings: arm: aspeed: add IBM P11 BMC boards
  ARM: dts: aspeed: Add IBM P11 FSI devices
  ARM: dts: aspeed: Add IBM P11 Blueridge BMC system
  ARM: dts: aspeed: Add IBM P11 Fuji BMC system

 .../bindings/arm/aspeed/aspeed.yaml           |    2 +
 .../fsi/aspeed,ast2600-fsi-master.yaml        |   72 +
 .../bindings/fsi/fsi-controller.yaml          |   65 +
 .../bindings/fsi/fsi-master-aspeed.txt        |   36 -
 .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  |   38 +
 .../devicetree/bindings/fsi/ibm,fsi2spi.yaml  |   11 +
 .../bindings/fsi/ibm,hub-fsi-controller.yaml  |   44 +
 .../bindings/fsi/ibm,i2cr-fsi-master.yaml     |    5 +-
 .../devicetree/bindings/fsi/ibm,p9-occ.txt    |   16 -
 .../devicetree/bindings/fsi/ibm,p9-occ.yaml   |   41 +
 .../bindings/fsi/ibm,p9-sbefifo.yaml          |   50 +
 .../devicetree/bindings/i2c/i2c-fsi.txt       |   40 -
 .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  |   59 +
 .../devicetree/bindings/spi/ibm,p10-spi.yaml  |   56 +
 arch/arm/boot/dts/aspeed/Makefile             |    2 +
 .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++
 .../boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts   | 3984 +++++++++++++++++
 .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++
 18 files changed, 7835 insertions(+), 93 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
 create mode 100644 Documentation/devicetree/bindings/fsi/fsi-controller.yaml
 delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
 delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml
 delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
 create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
 create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
 create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi

-- 
2.39.3

[PATCH v3 00/14] ARM: dts: aspeed: Add IBM P11 BMC Boards

[Eddie James]

Add the Blueridge and Fuji BMC systems. Document many missing FSI related
properties, and fix existing warnings.

Changes since v2:
 - Split up the DTS patches
 - Add documentation patches

Eddie James (14):
  dt-bindings: spi: Document the IBM Power SPI controller
  dt-bindings: fsi: fsi2spi: Document SPI controller child nodes
  dt-bindings: fsi: Document the FSI2PIB engine
  dt-bindings: fsi: p9-occ: Switch to yaml format
  dt-bindings: fsi: Document the IBM SBEFIFO engine
  dt-bindings: fsi: Document the FSI controller common properties
  dt-bindings: fsi: ibm,i2cr-fsi-master: Reference common FSI controller
  dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format
  dt-bindings: fsi: Document the FSI Hub Controller
  dt-bindings: i2c: i2c-fsi: Switch to yaml format
  dt-bindings: arm: aspeed: add IBM P11 BMC boards
  ARM: dts: aspeed: Add IBM P11 FSI devices
  ARM: dts: aspeed: Add IBM P11 Blueridge BMC system
  ARM: dts: aspeed: Add IBM P11 Fuji BMC system

 .../bindings/arm/aspeed/aspeed.yaml           |    2 +
 .../fsi/aspeed,ast2600-fsi-master.yaml        |   72 +
 .../bindings/fsi/fsi-controller.yaml          |   65 +
 .../bindings/fsi/fsi-master-aspeed.txt        |   36 -
 .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  |   38 +
 .../devicetree/bindings/fsi/ibm,fsi2spi.yaml  |   11 +
 .../bindings/fsi/ibm,hub-fsi-controller.yaml  |   44 +
 .../bindings/fsi/ibm,i2cr-fsi-master.yaml     |    5 +-
 .../devicetree/bindings/fsi/ibm,p9-occ.txt    |   16 -
 .../devicetree/bindings/fsi/ibm,p9-occ.yaml   |   41 +
 .../bindings/fsi/ibm,p9-sbefifo.yaml          |   50 +
 .../devicetree/bindings/i2c/i2c-fsi.txt       |   40 -
 .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  |   59 +
 .../devicetree/bindings/spi/ibm,p10-spi.yaml  |   56 +
 arch/arm/boot/dts/aspeed/Makefile             |    2 +
 .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++
 .../boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts   | 3984 +++++++++++++++++
 .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++
 18 files changed, 7835 insertions(+), 93 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
 create mode 100644 Documentation/devicetree/bindings/fsi/fsi-controller.yaml
 delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
 delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml
 delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
 create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
 create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
 create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi

-- 
2.39.3

[PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Eddie James]

The IBM Power chips have a basic SPI controller. Document it.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/spi/ibm,p10-spi.yaml  | 56 +++++++++++++++++++
 1 file changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml

diff --git a/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
new file mode 100644
index 000000000000..9bf57b621c1f
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/ibm,p10-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM SPI Controller
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  A basic SPI controller found on IBM Power chips, accessed over FSI. This
+  node will always be a child node of an ibm,fsi2spi node.
+
+properties:
+  compatible:
+    enum:
+      - ibm,p10-spi
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    fsi2spi at 1c00 {
+        compatible = "ibm,fsi2spi";
+        reg = <0x1c00 0x400>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        spi at 0 {
+            compatible = "ibm,p10-spi";
+            reg = <0>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            eeprom at 0 {
+                compatible = "atmel,at25";
+                reg = <0>;
+                size = <0x80000>;
+                address-width = <24>;
+                pagesize = <256>;
+                spi-max-frequency = <1000000>;
+            };
+        };
+    };
-- 
2.39.3

[PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Eddie James]

The IBM Power chips have a basic SPI controller. Document it.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/spi/ibm,p10-spi.yaml  | 56 +++++++++++++++++++
 1 file changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml

diff --git a/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
new file mode 100644
index 000000000000..9bf57b621c1f
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/ibm,p10-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM SPI Controller
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  A basic SPI controller found on IBM Power chips, accessed over FSI. This
+  node will always be a child node of an ibm,fsi2spi node.
+
+properties:
+  compatible:
+    enum:
+      - ibm,p10-spi
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    fsi2spi@1c00 {
+        compatible = "ibm,fsi2spi";
+        reg = <0x1c00 0x400>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        spi@0 {
+            compatible = "ibm,p10-spi";
+            reg = <0>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            eeprom@0 {
+                compatible = "atmel,at25";
+                reg = <0>;
+                size = <0x80000>;
+                address-width = <24>;
+                pagesize = <256>;
+                spi-max-frequency = <1000000>;
+            };
+        };
+    };
-- 
2.39.3

[PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Rob Herring]

On Thu, 25 Apr 2024 16:36:48 -0500, Eddie James wrote:
> The IBM Power chips have a basic SPI controller. Document it.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../devicetree/bindings/spi/ibm,p10-spi.yaml  | 56 +++++++++++++++++++
>  1 file changed, 56 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/spi/ibm,p10-spi.example.dtb: fsi2spi at 1c00: '#address-cells', '#size-cells', 'spi at 0' do not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/fsi/ibm,fsi2spi.yaml#

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240425213701.655540-2-eajames at linux.ibm.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Rob Herring]

On Thu, 25 Apr 2024 16:36:48 -0500, Eddie James wrote:
> The IBM Power chips have a basic SPI controller. Document it.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../devicetree/bindings/spi/ibm,p10-spi.yaml  | 56 +++++++++++++++++++
>  1 file changed, 56 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/spi/ibm,p10-spi.example.dtb: fsi2spi@1c00: '#address-cells', '#size-cells', 'spi@0' do not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/fsi/ibm,fsi2spi.yaml#

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240425213701.655540-2-eajames@linux.ibm.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

[PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> The IBM Power chips have a basic SPI controller. Document it.

Please use subject prefixes matching the subsystem. You can get them for
example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
your patch is touching.

> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../devicetree/bindings/spi/ibm,p10-spi.yaml  | 56 +++++++++++++++++++
>  1 file changed, 56 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
> 
> diff --git a/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
> new file mode 100644
> index 000000000000..9bf57b621c1f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
> @@ -0,0 +1,56 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/ibm,p10-spi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM SPI Controller

IBM P10 SPI Controller

> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  A basic SPI controller found on IBM Power chips, accessed over FSI. This
> +  node will always be a child node of an ibm,fsi2spi node.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,p10-spi
> +
> +  reg:
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +
> +allOf:
> +  - $ref: spi-controller.yaml#
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    fsi2spi at 1c00 {
> +        compatible = "ibm,fsi2spi";
> +        reg = <0x1c00 0x400>;
> +        #address-cells = <1>;
> +        #size-cells = <0>;

Use rather some simple wrapper instead of node causing warnings, e.g.
fsi {} with only address/size cells.



Best regards,
Krzysztof

Re: [PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> The IBM Power chips have a basic SPI controller. Document it.

Please use subject prefixes matching the subsystem. You can get them for
example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
your patch is touching.

> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../devicetree/bindings/spi/ibm,p10-spi.yaml  | 56 +++++++++++++++++++
>  1 file changed, 56 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
> 
> diff --git a/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
> new file mode 100644
> index 000000000000..9bf57b621c1f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
> @@ -0,0 +1,56 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/ibm,p10-spi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM SPI Controller

IBM P10 SPI Controller

> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  A basic SPI controller found on IBM Power chips, accessed over FSI. This
> +  node will always be a child node of an ibm,fsi2spi node.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,p10-spi
> +
> +  reg:
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +
> +allOf:
> +  - $ref: spi-controller.yaml#
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    fsi2spi@1c00 {
> +        compatible = "ibm,fsi2spi";
> +        reg = <0x1c00 0x400>;
> +        #address-cells = <1>;
> +        #size-cells = <0>;

Use rather some simple wrapper instead of node causing warnings, e.g.
fsi {} with only address/size cells.



Best regards,
Krzysztof

[PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Eddie James]

On 4/26/24 01:15, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> The IBM Power chips have a basic SPI controller. Document it.
> Please use subject prefixes matching the subsystem. You can get them for
> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
> your patch is touching.


Isn't spi the right subsystem here?


>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../devicetree/bindings/spi/ibm,p10-spi.yaml  | 56 +++++++++++++++++++
>>   1 file changed, 56 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
>> new file mode 100644
>> index 000000000000..9bf57b621c1f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
>> @@ -0,0 +1,56 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/spi/ibm,p10-spi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM SPI Controller
> IBM P10 SPI Controller


Ack.


>
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  A basic SPI controller found on IBM Power chips, accessed over FSI. This
>> +  node will always be a child node of an ibm,fsi2spi node.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,p10-spi
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +
>> +allOf:
>> +  - $ref: spi-controller.yaml#
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    fsi2spi at 1c00 {
>> +        compatible = "ibm,fsi2spi";
>> +        reg = <0x1c00 0x400>;
>> +        #address-cells = <1>;
>> +        #size-cells = <0>;
> Use rather some simple wrapper instead of node causing warnings, e.g.
> fsi {} with only address/size cells.


Will do, thanks.


>
>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Eddie James]

On 4/26/24 01:15, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> The IBM Power chips have a basic SPI controller. Document it.
> Please use subject prefixes matching the subsystem. You can get them for
> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
> your patch is touching.


Isn't spi the right subsystem here?


>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../devicetree/bindings/spi/ibm,p10-spi.yaml  | 56 +++++++++++++++++++
>>   1 file changed, 56 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
>> new file mode 100644
>> index 000000000000..9bf57b621c1f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
>> @@ -0,0 +1,56 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/spi/ibm,p10-spi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM SPI Controller
> IBM P10 SPI Controller


Ack.


>
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  A basic SPI controller found on IBM Power chips, accessed over FSI. This
>> +  node will always be a child node of an ibm,fsi2spi node.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,p10-spi
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +
>> +allOf:
>> +  - $ref: spi-controller.yaml#
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    fsi2spi@1c00 {
>> +        compatible = "ibm,fsi2spi";
>> +        reg = <0x1c00 0x400>;
>> +        #address-cells = <1>;
>> +        #size-cells = <0>;
> Use rather some simple wrapper instead of node causing warnings, e.g.
> fsi {} with only address/size cells.


Will do, thanks.


>
>
>
> Best regards,
> Krzysztof
>

[PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Krzysztof Kozlowski]

On 26/04/2024 16:49, Eddie James wrote:
> 
> On 4/26/24 01:15, Krzysztof Kozlowski wrote:
>> On 25/04/2024 23:36, Eddie James wrote:
>>> The IBM Power chips have a basic SPI controller. Document it.
>> Please use subject prefixes matching the subsystem. You can get them for
>> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
>> your patch is touching.
> 
> 
> Isn't spi the right subsystem here?

And what prefix shall be for SPI bindings? Did you run the command or
just replying to disagree with me?


Best regards,
Krzysztof

Re: [PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Krzysztof Kozlowski]

On 26/04/2024 16:49, Eddie James wrote:
> 
> On 4/26/24 01:15, Krzysztof Kozlowski wrote:
>> On 25/04/2024 23:36, Eddie James wrote:
>>> The IBM Power chips have a basic SPI controller. Document it.
>> Please use subject prefixes matching the subsystem. You can get them for
>> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
>> your patch is touching.
> 
> 
> Isn't spi the right subsystem here?

And what prefix shall be for SPI bindings? Did you run the command or
just replying to disagree with me?


Best regards,
Krzysztof

[PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Eddie James]

On 4/28/24 11:39, Krzysztof Kozlowski wrote:
> On 26/04/2024 16:49, Eddie James wrote:
>> On 4/26/24 01:15, Krzysztof Kozlowski wrote:
>>> On 25/04/2024 23:36, Eddie James wrote:
>>>> The IBM Power chips have a basic SPI controller. Document it.
>>> Please use subject prefixes matching the subsystem. You can get them for
>>> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
>>> your patch is touching.
>>
>> Isn't spi the right subsystem here?
> And what prefix shall be for SPI bindings? Did you run the command or
> just replying to disagree with me?


The correct prefix is either dt-bindings: spi or spi: dt-bindings. I 
used the former. Would you prefer I use the latter? I followed your 
instructions but you see the results are mixed, which is why I asked for 
clarification, wondering if you meant something else, since I already 
used one of the two apparently correct options.


53df0409b59b Merge branch 'for-next' of 
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git
f63175733f91 spi: dt-bindings: armada-3700: convert to dtschema
1f48cbd6f00f spi: renesas,sh-msiof: Add r8a779h0 support
eb4fdb4bf46f spi: dt-bindings: cdns,qspi-nor: make cdns,fifo-depth optional
52826aee484b spi: dt-bindings: cdns,qspi-nor: add mobileye,eyeq5-ospi 
compatible
002514d91fcc spi: dt-bindings: cdns,qspi-nor: sort compatibles 
alphabetically
02ec75edaa94 dt-bindings: treewide: add access-controllers description
80a38bfbbd59 spi: dt-bindings: introduce FIFO depth properties
ee09bb727bff spi: dt-bindings: samsung: make dma properties not required
666db8fd4265 spi: dt-bindings: atmel,at91rm9200-spi: remove 9x60 
compatible from list
ff690e75d64b spi: dt-bindings: samsung: add google,gs101-spi compatible
737cf74b3800 spi: dt-bindings: samsung: Add Exynos850 SPI
18ab9e9e8889 dt-bindings: spi: nxp-fspi: support i.MX93 and i.MX95
6685d552a0cc dt-bindings: spi: fsl-lpspi: support i.MX95 LPSPI
f034a151059a dt-bindings: spi: stm32: add st,stm32mp25-spi compatible
e1fca6957f19 spi: dw: Remove Intel Thunder Bay SOC support
4c3ff31a85e3 spi: axi-spi-engine improvements
252eafe11ffc dt-bindings: spi: axi-spi-engine: convert to yaml
54a1dc08e173 spi: dt-bindings: renesas,rspi: Document RZ/Five SoC
09388379b6d7 spi: add stm32f7-spi compatible
1b2e883e1af8 spi: Merge up fix
4056d88866e5 spi: renesas,rzv2m-csi: Add CSI (SPI) target related property
9f778f377cd3 spi: dt-bindings: Make "additionalProperties: true" explicit
da6de6d3ecc1 spi: qup: Allow scaling power domains and
0fc57bf1b2ff spi: dt-bindings: st,stm32-spi: Move "st,spi-midi-ns" to 
spi-peripheral-props.yaml
d15befc0cef4 spi: dt-bindings: qup: Document interconnects
e6419c35f0d9 spi: dt-bindings: qup: Document power-domains and OPP
3b4e5194138b dt-bindings: spi: fsl-imx-cspi: Document missing entries
b0ef97ac89a7 spi: dt-bindings: arm,pl022: Move child node properties to 
separate schema
8f447694c23a Merge tag 'devicetree-for-6.6' of 
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
47aab53331ef dt-bindings: Fix typos
0e19118ab24b dt-bindings: spi: convert spi-brcm63xx.txt to YAML
0d2b6a1b8515 dt-bindings: qspi: cdns,qspi-nor: Add clocks for StarFive 
JH7110 SoC
ffae65fb1ae4 dt-bindings: spi: spi-cadence: Add label property
883622752403 dt-bindings: spi: spi-cadence: Describe power-domains property
b350e6c6297a spi: dt-bindings: add loongson spi
026badeb7055 spi: fspi: Add power-domains to the DT bindings
49aa77165c00 spi: lpspi: Add power-domains to the DT bindings
8858babff615 dt-bindings: spi: add reference file to YAML
b8968c388b69 dt-bindings: spi: Convert Tegra114 SPI to json-schema
17a9ab02f72c dt-bindings: spi: tegra-sflash: Convert to json-schema
8c87a46e2ce3 dt-bindings: spi: tegra-slink: Convert to json-schema
6c1561fb9005 Merge tag 'soc-dt-6.5' of 
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
e884a133340a spi: dt-bindings: atmel,at91rm9200-spi: fix broken sam9x7 
compatible
a3eb95484f27 spi: dt-bindings: atmel,at91rm9200-spi: add sam9x7 compatible
14dde0746e67 spi: dt-bindings: Add bindings for RZ/V2M CSI
01fa9edd8bcf spi: dt-bindings: stm32: do not disable spi-slave property 
for stm32f4-f7
e6afe03351ac spi: stm32: disable spi-slave property for stm32f4-f7
7bac98a338d6 spi: dt-bindings: snps,dw-apb-ssi: Add compatible for Intel 
Mount Evans SoC
d5c421d24d7e dt-bindings: xilinx: Switch xilinx.com emails to amd.com
34fcc0f0a410 spi: dt-bindings: socionext,uniphier: drop address/size-cells
bbd25f1ae8bf spi: dt-bindings: samsung: drop cs-gpios


>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Eddie James]

On 4/28/24 11:39, Krzysztof Kozlowski wrote:
> On 26/04/2024 16:49, Eddie James wrote:
>> On 4/26/24 01:15, Krzysztof Kozlowski wrote:
>>> On 25/04/2024 23:36, Eddie James wrote:
>>>> The IBM Power chips have a basic SPI controller. Document it.
>>> Please use subject prefixes matching the subsystem. You can get them for
>>> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
>>> your patch is touching.
>>
>> Isn't spi the right subsystem here?
> And what prefix shall be for SPI bindings? Did you run the command or
> just replying to disagree with me?


The correct prefix is either dt-bindings: spi or spi: dt-bindings. I 
used the former. Would you prefer I use the latter? I followed your 
instructions but you see the results are mixed, which is why I asked for 
clarification, wondering if you meant something else, since I already 
used one of the two apparently correct options.


53df0409b59b Merge branch 'for-next' of 
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git
f63175733f91 spi: dt-bindings: armada-3700: convert to dtschema
1f48cbd6f00f spi: renesas,sh-msiof: Add r8a779h0 support
eb4fdb4bf46f spi: dt-bindings: cdns,qspi-nor: make cdns,fifo-depth optional
52826aee484b spi: dt-bindings: cdns,qspi-nor: add mobileye,eyeq5-ospi 
compatible
002514d91fcc spi: dt-bindings: cdns,qspi-nor: sort compatibles 
alphabetically
02ec75edaa94 dt-bindings: treewide: add access-controllers description
80a38bfbbd59 spi: dt-bindings: introduce FIFO depth properties
ee09bb727bff spi: dt-bindings: samsung: make dma properties not required
666db8fd4265 spi: dt-bindings: atmel,at91rm9200-spi: remove 9x60 
compatible from list
ff690e75d64b spi: dt-bindings: samsung: add google,gs101-spi compatible
737cf74b3800 spi: dt-bindings: samsung: Add Exynos850 SPI
18ab9e9e8889 dt-bindings: spi: nxp-fspi: support i.MX93 and i.MX95
6685d552a0cc dt-bindings: spi: fsl-lpspi: support i.MX95 LPSPI
f034a151059a dt-bindings: spi: stm32: add st,stm32mp25-spi compatible
e1fca6957f19 spi: dw: Remove Intel Thunder Bay SOC support
4c3ff31a85e3 spi: axi-spi-engine improvements
252eafe11ffc dt-bindings: spi: axi-spi-engine: convert to yaml
54a1dc08e173 spi: dt-bindings: renesas,rspi: Document RZ/Five SoC
09388379b6d7 spi: add stm32f7-spi compatible
1b2e883e1af8 spi: Merge up fix
4056d88866e5 spi: renesas,rzv2m-csi: Add CSI (SPI) target related property
9f778f377cd3 spi: dt-bindings: Make "additionalProperties: true" explicit
da6de6d3ecc1 spi: qup: Allow scaling power domains and
0fc57bf1b2ff spi: dt-bindings: st,stm32-spi: Move "st,spi-midi-ns" to 
spi-peripheral-props.yaml
d15befc0cef4 spi: dt-bindings: qup: Document interconnects
e6419c35f0d9 spi: dt-bindings: qup: Document power-domains and OPP
3b4e5194138b dt-bindings: spi: fsl-imx-cspi: Document missing entries
b0ef97ac89a7 spi: dt-bindings: arm,pl022: Move child node properties to 
separate schema
8f447694c23a Merge tag 'devicetree-for-6.6' of 
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
47aab53331ef dt-bindings: Fix typos
0e19118ab24b dt-bindings: spi: convert spi-brcm63xx.txt to YAML
0d2b6a1b8515 dt-bindings: qspi: cdns,qspi-nor: Add clocks for StarFive 
JH7110 SoC
ffae65fb1ae4 dt-bindings: spi: spi-cadence: Add label property
883622752403 dt-bindings: spi: spi-cadence: Describe power-domains property
b350e6c6297a spi: dt-bindings: add loongson spi
026badeb7055 spi: fspi: Add power-domains to the DT bindings
49aa77165c00 spi: lpspi: Add power-domains to the DT bindings
8858babff615 dt-bindings: spi: add reference file to YAML
b8968c388b69 dt-bindings: spi: Convert Tegra114 SPI to json-schema
17a9ab02f72c dt-bindings: spi: tegra-sflash: Convert to json-schema
8c87a46e2ce3 dt-bindings: spi: tegra-slink: Convert to json-schema
6c1561fb9005 Merge tag 'soc-dt-6.5' of 
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
e884a133340a spi: dt-bindings: atmel,at91rm9200-spi: fix broken sam9x7 
compatible
a3eb95484f27 spi: dt-bindings: atmel,at91rm9200-spi: add sam9x7 compatible
14dde0746e67 spi: dt-bindings: Add bindings for RZ/V2M CSI
01fa9edd8bcf spi: dt-bindings: stm32: do not disable spi-slave property 
for stm32f4-f7
e6afe03351ac spi: stm32: disable spi-slave property for stm32f4-f7
7bac98a338d6 spi: dt-bindings: snps,dw-apb-ssi: Add compatible for Intel 
Mount Evans SoC
d5c421d24d7e dt-bindings: xilinx: Switch xilinx.com emails to amd.com
34fcc0f0a410 spi: dt-bindings: socionext,uniphier: drop address/size-cells
bbd25f1ae8bf spi: dt-bindings: samsung: drop cs-gpios


>
>
> Best regards,
> Krzysztof
>

[PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Krzysztof Kozlowski]

On 29/04/2024 16:38, Eddie James wrote:
> 
> On 4/28/24 11:39, Krzysztof Kozlowski wrote:
>> On 26/04/2024 16:49, Eddie James wrote:
>>> On 4/26/24 01:15, Krzysztof Kozlowski wrote:
>>>> On 25/04/2024 23:36, Eddie James wrote:
>>>>> The IBM Power chips have a basic SPI controller. Document it.
>>>> Please use subject prefixes matching the subsystem. You can get them for
>>>> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
>>>> your patch is touching.
>>>
>>> Isn't spi the right subsystem here?
>> And what prefix shall be for SPI bindings? Did you run the command or
>> just replying to disagree with me?
> 
> 
> The correct prefix is either dt-bindings: spi or spi: dt-bindings. I 
> used the former. Would you prefer I use the latter? I followed your 

The correct is the latter, although I see now Mark stopped stripping
dt-bindings in such case. Log is still suggesting that (git log
--oneline -- Documentation/devicetree/bindings/spi/ | grep "^[0-9a-f]\+
spi:" | wc -l gives 370 vs 130), although I understand now different
approach.

It's also mentioned here:
https://www.kernel.org/doc/html/latest/devicetree/bindings/submitting-patches.html


Best regards,
Krzysztof

Re: [PATCH v3 01/14] dt-bindings: spi: Document the IBM Power SPI controller

[Krzysztof Kozlowski]

On 29/04/2024 16:38, Eddie James wrote:
> 
> On 4/28/24 11:39, Krzysztof Kozlowski wrote:
>> On 26/04/2024 16:49, Eddie James wrote:
>>> On 4/26/24 01:15, Krzysztof Kozlowski wrote:
>>>> On 25/04/2024 23:36, Eddie James wrote:
>>>>> The IBM Power chips have a basic SPI controller. Document it.
>>>> Please use subject prefixes matching the subsystem. You can get them for
>>>> example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
>>>> your patch is touching.
>>>
>>> Isn't spi the right subsystem here?
>> And what prefix shall be for SPI bindings? Did you run the command or
>> just replying to disagree with me?
> 
> 
> The correct prefix is either dt-bindings: spi or spi: dt-bindings. I 
> used the former. Would you prefer I use the latter? I followed your 

The correct is the latter, although I see now Mark stopped stripping
dt-bindings in such case. Log is still suggesting that (git log
--oneline -- Documentation/devicetree/bindings/spi/ | grep "^[0-9a-f]\+
spi:" | wc -l gives 370 vs 130), although I understand now different
approach.

It's also mentioned here:
https://www.kernel.org/doc/html/latest/devicetree/bindings/submitting-patches.html


Best regards,
Krzysztof

[PATCH v3 02/14] dt-bindings: fsi: fsi2spi: Document SPI controller child nodes

[Eddie James]

The FSI2SPI bridge has several SPI controllers behind it, which
should be documented. Also, therefore the node needs to specify
address and size cells.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/fsi/ibm,fsi2spi.yaml          | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2spi.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2spi.yaml
index e2ca0b000471..512d6d4dff3c 100644
--- a/Documentation/devicetree/bindings/fsi/ibm,fsi2spi.yaml
+++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2spi.yaml
@@ -24,6 +24,17 @@ properties:
     items:
       - description: FSI slave address
 
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "^spi@[0-9a-f]+$":
+    $ref: /schemas/spi/ibm,p10-spi.yaml
+    description: Child node describing underlying SPI controller
+
 required:
   - compatible
   - reg
-- 
2.39.3

[PATCH v3 02/14] dt-bindings: fsi: fsi2spi: Document SPI controller child nodes

[Eddie James]

The FSI2SPI bridge has several SPI controllers behind it, which
should be documented. Also, therefore the node needs to specify
address and size cells.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/fsi/ibm,fsi2spi.yaml          | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2spi.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2spi.yaml
index e2ca0b000471..512d6d4dff3c 100644
--- a/Documentation/devicetree/bindings/fsi/ibm,fsi2spi.yaml
+++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2spi.yaml
@@ -24,6 +24,17 @@ properties:
     items:
       - description: FSI slave address
 
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "^spi@[0-9a-f]+$":
+    $ref: /schemas/spi/ibm,p10-spi.yaml
+    description: Child node describing underlying SPI controller
+
 required:
   - compatible
   - reg
-- 
2.39.3

[PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Eddie James]

The FSI2PIB or SCOM engine provides an interface to the POWER processor
PIB (Pervasive Interconnect Bus).

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
 1 file changed, 38 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml

diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
new file mode 100644
index 000000000000..4d557150c2e3
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
@@ -0,0 +1,38 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached SCOM engine
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  The SCOM engine is an interface to the POWER processor PIB (Pervasive
+  Interconnect Bus). This node will always be a child of an FSI CFAM node;
+  see fsi.txt for details on FSI slave and CFAM nodes.
+
+properties:
+  compatible:
+    enum:
+      - ibm,fsi2pib
+      - ibm,i2cr-scom
+
+  reg:
+    items:
+      - description: FSI slave address
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    scom at 1000 {
+        compatible = "ibm,fsi2pib";
+        reg = <0x1000 0x400>;
+    };
-- 
2.39.3

[PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Eddie James]

The FSI2PIB or SCOM engine provides an interface to the POWER processor
PIB (Pervasive Interconnect Bus).

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
 1 file changed, 38 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml

diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
new file mode 100644
index 000000000000..4d557150c2e3
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
@@ -0,0 +1,38 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached SCOM engine
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  The SCOM engine is an interface to the POWER processor PIB (Pervasive
+  Interconnect Bus). This node will always be a child of an FSI CFAM node;
+  see fsi.txt for details on FSI slave and CFAM nodes.
+
+properties:
+  compatible:
+    enum:
+      - ibm,fsi2pib
+      - ibm,i2cr-scom
+
+  reg:
+    items:
+      - description: FSI slave address
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    scom@1000 {
+        compatible = "ibm,fsi2pib";
+        reg = <0x1000 0x400>;
+    };
-- 
2.39.3

[PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> The FSI2PIB or SCOM engine provides an interface to the POWER processor
> PIB (Pervasive Interconnect Bus).
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>


---

This is an automated instruction, just in case, because many review tags
are being ignored. If you know the process, you can skip it (please do
not feel offended by me posting it here - no bad intentions intended).
If you do not know the process, here is a short explanation:

Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions, under or above your Signed-off-by tag. Tag is "received", when
provided in a message replied to you on the mailing list. Tools like b4
can help here. However, there's no need to repost patches *only* to add
the tags. The upstream maintainer will do that for tags received on the
version they apply.

https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577

Best regards,
Krzysztof

Re: [PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> The FSI2PIB or SCOM engine provides an interface to the POWER processor
> PIB (Pervasive Interconnect Bus).
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>


---

This is an automated instruction, just in case, because many review tags
are being ignored. If you know the process, you can skip it (please do
not feel offended by me posting it here - no bad intentions intended).
If you do not know the process, here is a short explanation:

Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions, under or above your Signed-off-by tag. Tag is "received", when
provided in a message replied to you on the mailing list. Tools like b4
can help here. However, there's no need to repost patches *only* to add
the tags. The upstream maintainer will do that for tags received on the
version they apply.

https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577

Best regards,
Krzysztof

[PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> The FSI2PIB or SCOM engine provides an interface to the POWER processor
> PIB (Pervasive Interconnect Bus).
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
>  1 file changed, 38 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
> 
> diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
> new file mode 100644
> index 000000000000..4d557150c2e3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
> @@ -0,0 +1,38 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM FSI-attached SCOM engine
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  The SCOM engine is an interface to the POWER processor PIB (Pervasive
> +  Interconnect Bus). This node will always be a child of an FSI CFAM node;
> +  see fsi.txt for details on FSI slave and CFAM nodes.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,fsi2pib
> +      - ibm,i2cr-scom

Sometimes you call these p9, sometimes p10... what is the system or SoC
here? Aren't you adding some generic compatibles? writing-bindings and
numerous guides are clear on that.

Best regards,
Krzysztof

Re: [PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> The FSI2PIB or SCOM engine provides an interface to the POWER processor
> PIB (Pervasive Interconnect Bus).
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
>  1 file changed, 38 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
> 
> diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
> new file mode 100644
> index 000000000000..4d557150c2e3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
> @@ -0,0 +1,38 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM FSI-attached SCOM engine
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  The SCOM engine is an interface to the POWER processor PIB (Pervasive
> +  Interconnect Bus). This node will always be a child of an FSI CFAM node;
> +  see fsi.txt for details on FSI slave and CFAM nodes.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,fsi2pib
> +      - ibm,i2cr-scom

Sometimes you call these p9, sometimes p10... what is the system or SoC
here? Aren't you adding some generic compatibles? writing-bindings and
numerous guides are clear on that.

Best regards,
Krzysztof

[PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Eddie James]

On 4/26/24 01:18, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> The FSI2PIB or SCOM engine provides an interface to the POWER processor
>> PIB (Pervasive Interconnect Bus).
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
>>   1 file changed, 38 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>> new file mode 100644
>> index 000000000000..4d557150c2e3
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>> @@ -0,0 +1,38 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM FSI-attached SCOM engine
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  The SCOM engine is an interface to the POWER processor PIB (Pervasive
>> +  Interconnect Bus). This node will always be a child of an FSI CFAM node;
>> +  see fsi.txt for details on FSI slave and CFAM nodes.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,fsi2pib
>> +      - ibm,i2cr-scom
> Sometimes you call these p9, sometimes p10... what is the system or SoC
> here? Aren't you adding some generic compatibles? writing-bindings and
> numerous guides are clear on that.


Open source FSI support started with P9 chips so we initially added 
p9-sbefifo, p9-occ, etc. P10 has all of the same engines as P9 plus the 
SPI controller, so that's why SPI is p10-spi. P11 has the same engines 
as P10. For scom/fsi2pib we could call it p9-scom I suppose... This 
series isn't just documentation for a new system, I'm adding 
documentation that should have been added for P9. Anyway I'm not sure 
what you mean about generic compatibles? You mean just add a "scom" or 
"fsi2pib" compatible? writing-bindings says "DO make 'compatible' 
properties specific"


Thanks,

Eddie


>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Eddie James]

On 4/26/24 01:18, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> The FSI2PIB or SCOM engine provides an interface to the POWER processor
>> PIB (Pervasive Interconnect Bus).
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
>>   1 file changed, 38 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>> new file mode 100644
>> index 000000000000..4d557150c2e3
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>> @@ -0,0 +1,38 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM FSI-attached SCOM engine
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  The SCOM engine is an interface to the POWER processor PIB (Pervasive
>> +  Interconnect Bus). This node will always be a child of an FSI CFAM node;
>> +  see fsi.txt for details on FSI slave and CFAM nodes.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,fsi2pib
>> +      - ibm,i2cr-scom
> Sometimes you call these p9, sometimes p10... what is the system or SoC
> here? Aren't you adding some generic compatibles? writing-bindings and
> numerous guides are clear on that.


Open source FSI support started with P9 chips so we initially added 
p9-sbefifo, p9-occ, etc. P10 has all of the same engines as P9 plus the 
SPI controller, so that's why SPI is p10-spi. P11 has the same engines 
as P10. For scom/fsi2pib we could call it p9-scom I suppose... This 
series isn't just documentation for a new system, I'm adding 
documentation that should have been added for P9. Anyway I'm not sure 
what you mean about generic compatibles? You mean just add a "scom" or 
"fsi2pib" compatible? writing-bindings says "DO make 'compatible' 
properties specific"


Thanks,

Eddie


>
> Best regards,
> Krzysztof
>

[PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Krzysztof Kozlowski]

On 26/04/2024 17:00, Eddie James wrote:
> 
> On 4/26/24 01:18, Krzysztof Kozlowski wrote:
>> On 25/04/2024 23:36, Eddie James wrote:
>>> The FSI2PIB or SCOM engine provides an interface to the POWER processor
>>> PIB (Pervasive Interconnect Bus).
>>>
>>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>>> ---
>>>   .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
>>>   1 file changed, 38 insertions(+)
>>>   create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>>
>>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>> new file mode 100644
>>> index 000000000000..4d557150c2e3
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>> @@ -0,0 +1,38 @@
>>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>>> +%YAML 1.2
>>> +---
>>> +$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>>> +
>>> +title: IBM FSI-attached SCOM engine
>>> +
>>> +maintainers:
>>> +  - Eddie James <eajames@linux.ibm.com>
>>> +
>>> +description:
>>> +  The SCOM engine is an interface to the POWER processor PIB (Pervasive
>>> +  Interconnect Bus). This node will always be a child of an FSI CFAM node;
>>> +  see fsi.txt for details on FSI slave and CFAM nodes.
>>> +
>>> +properties:
>>> +  compatible:
>>> +    enum:
>>> +      - ibm,fsi2pib
>>> +      - ibm,i2cr-scom
>> Sometimes you call these p9, sometimes p10... what is the system or SoC
>> here? Aren't you adding some generic compatibles? writing-bindings and
>> numerous guides are clear on that.
> 
> 
> Open source FSI support started with P9 chips so we initially added 
> p9-sbefifo, p9-occ, etc. P10 has all of the same engines as P9 plus the 
> SPI controller, so that's why SPI is p10-spi. P11 has the same engines 
> as P10. For scom/fsi2pib we could call it p9-scom I suppose... This 
> series isn't just documentation for a new system, I'm adding 
> documentation that should have been added for P9. Anyway I'm not sure 
> what you mean about generic compatibles? You mean just add a "scom" or 
> "fsi2pib" compatible? writing-bindings says "DO make 'compatible' 
> properties specific"

Usually it means that parts of SoC must have the name of the SoC, as
first component of the name. Your boards are a bit different here,
because I suppose no one will ever make a product except you, but still
code could follow same set of rules.

Best regards,
Krzysztof

Re: [PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Krzysztof Kozlowski]

On 26/04/2024 17:00, Eddie James wrote:
> 
> On 4/26/24 01:18, Krzysztof Kozlowski wrote:
>> On 25/04/2024 23:36, Eddie James wrote:
>>> The FSI2PIB or SCOM engine provides an interface to the POWER processor
>>> PIB (Pervasive Interconnect Bus).
>>>
>>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>>> ---
>>>   .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
>>>   1 file changed, 38 insertions(+)
>>>   create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>>
>>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>> new file mode 100644
>>> index 000000000000..4d557150c2e3
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>> @@ -0,0 +1,38 @@
>>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>>> +%YAML 1.2
>>> +---
>>> +$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>>> +
>>> +title: IBM FSI-attached SCOM engine
>>> +
>>> +maintainers:
>>> +  - Eddie James <eajames@linux.ibm.com>
>>> +
>>> +description:
>>> +  The SCOM engine is an interface to the POWER processor PIB (Pervasive
>>> +  Interconnect Bus). This node will always be a child of an FSI CFAM node;
>>> +  see fsi.txt for details on FSI slave and CFAM nodes.
>>> +
>>> +properties:
>>> +  compatible:
>>> +    enum:
>>> +      - ibm,fsi2pib
>>> +      - ibm,i2cr-scom
>> Sometimes you call these p9, sometimes p10... what is the system or SoC
>> here? Aren't you adding some generic compatibles? writing-bindings and
>> numerous guides are clear on that.
> 
> 
> Open source FSI support started with P9 chips so we initially added 
> p9-sbefifo, p9-occ, etc. P10 has all of the same engines as P9 plus the 
> SPI controller, so that's why SPI is p10-spi. P11 has the same engines 
> as P10. For scom/fsi2pib we could call it p9-scom I suppose... This 
> series isn't just documentation for a new system, I'm adding 
> documentation that should have been added for P9. Anyway I'm not sure 
> what you mean about generic compatibles? You mean just add a "scom" or 
> "fsi2pib" compatible? writing-bindings says "DO make 'compatible' 
> properties specific"

Usually it means that parts of SoC must have the name of the SoC, as
first component of the name. Your boards are a bit different here,
because I suppose no one will ever make a product except you, but still
code could follow same set of rules.

Best regards,
Krzysztof

[PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Eddie James]

On 4/28/24 11:41, Krzysztof Kozlowski wrote:
> On 26/04/2024 17:00, Eddie James wrote:
>> On 4/26/24 01:18, Krzysztof Kozlowski wrote:
>>> On 25/04/2024 23:36, Eddie James wrote:
>>>> The FSI2PIB or SCOM engine provides an interface to the POWER processor
>>>> PIB (Pervasive Interconnect Bus).
>>>>
>>>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>>>> ---
>>>>    .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
>>>>    1 file changed, 38 insertions(+)
>>>>    create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>>> new file mode 100644
>>>> index 000000000000..4d557150c2e3
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>>> @@ -0,0 +1,38 @@
>>>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>>>> +%YAML 1.2
>>>> +---
>>>> +$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
>>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>>>> +
>>>> +title: IBM FSI-attached SCOM engine
>>>> +
>>>> +maintainers:
>>>> +  - Eddie James <eajames@linux.ibm.com>
>>>> +
>>>> +description:
>>>> +  The SCOM engine is an interface to the POWER processor PIB (Pervasive
>>>> +  Interconnect Bus). This node will always be a child of an FSI CFAM node;
>>>> +  see fsi.txt for details on FSI slave and CFAM nodes.
>>>> +
>>>> +properties:
>>>> +  compatible:
>>>> +    enum:
>>>> +      - ibm,fsi2pib
>>>> +      - ibm,i2cr-scom
>>> Sometimes you call these p9, sometimes p10... what is the system or SoC
>>> here? Aren't you adding some generic compatibles? writing-bindings and
>>> numerous guides are clear on that.
>>
>> Open source FSI support started with P9 chips so we initially added
>> p9-sbefifo, p9-occ, etc. P10 has all of the same engines as P9 plus the
>> SPI controller, so that's why SPI is p10-spi. P11 has the same engines
>> as P10. For scom/fsi2pib we could call it p9-scom I suppose... This
>> series isn't just documentation for a new system, I'm adding
>> documentation that should have been added for P9. Anyway I'm not sure
>> what you mean about generic compatibles? You mean just add a "scom" or
>> "fsi2pib" compatible? writing-bindings says "DO make 'compatible'
>> properties specific"
> Usually it means that parts of SoC must have the name of the SoC, as
> first component of the name. Your boards are a bit different here,
> because I suppose no one will ever make a product except you, but still
> code could follow same set of rules.


OK, this wasn't mentioned when fsi2spi binding was merged, and I thought 
to make fsi2pib the same. I can switch to p9-scom or something.


Thanks,

Eddie



>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 03/14] dt-bindings: fsi: Document the FSI2PIB engine

[Eddie James]

On 4/28/24 11:41, Krzysztof Kozlowski wrote:
> On 26/04/2024 17:00, Eddie James wrote:
>> On 4/26/24 01:18, Krzysztof Kozlowski wrote:
>>> On 25/04/2024 23:36, Eddie James wrote:
>>>> The FSI2PIB or SCOM engine provides an interface to the POWER processor
>>>> PIB (Pervasive Interconnect Bus).
>>>>
>>>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>>>> ---
>>>>    .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  | 38 +++++++++++++++++++
>>>>    1 file changed, 38 insertions(+)
>>>>    create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>>> new file mode 100644
>>>> index 000000000000..4d557150c2e3
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>>>> @@ -0,0 +1,38 @@
>>>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>>>> +%YAML 1.2
>>>> +---
>>>> +$id: http://devicetree.org/schemas/fsi/ibm,fsi2pib.yaml#
>>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>>>> +
>>>> +title: IBM FSI-attached SCOM engine
>>>> +
>>>> +maintainers:
>>>> +  - Eddie James <eajames@linux.ibm.com>
>>>> +
>>>> +description:
>>>> +  The SCOM engine is an interface to the POWER processor PIB (Pervasive
>>>> +  Interconnect Bus). This node will always be a child of an FSI CFAM node;
>>>> +  see fsi.txt for details on FSI slave and CFAM nodes.
>>>> +
>>>> +properties:
>>>> +  compatible:
>>>> +    enum:
>>>> +      - ibm,fsi2pib
>>>> +      - ibm,i2cr-scom
>>> Sometimes you call these p9, sometimes p10... what is the system or SoC
>>> here? Aren't you adding some generic compatibles? writing-bindings and
>>> numerous guides are clear on that.
>>
>> Open source FSI support started with P9 chips so we initially added
>> p9-sbefifo, p9-occ, etc. P10 has all of the same engines as P9 plus the
>> SPI controller, so that's why SPI is p10-spi. P11 has the same engines
>> as P10. For scom/fsi2pib we could call it p9-scom I suppose... This
>> series isn't just documentation for a new system, I'm adding
>> documentation that should have been added for P9. Anyway I'm not sure
>> what you mean about generic compatibles? You mean just add a "scom" or
>> "fsi2pib" compatible? writing-bindings says "DO make 'compatible'
>> properties specific"
> Usually it means that parts of SoC must have the name of the SoC, as
> first component of the name. Your boards are a bit different here,
> because I suppose no one will ever make a product except you, but still
> code could follow same set of rules.


OK, this wasn't mentioned when fsi2spi binding was merged, and I thought 
to make fsi2pib the same. I can switch to p9-scom or something.


Thanks,

Eddie



>
> Best regards,
> Krzysztof
>

[PATCH v3 04/14] dt-bindings: fsi: p9-occ: Switch to yaml format

[Eddie James]

Switch to yaml for the OCC documentation. Also document the fact
that the OCC "bridge" device will often have the hwmon node as a
child.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/fsi/ibm,p9-occ.txt    | 16 --------
 .../devicetree/bindings/fsi/ibm,p9-occ.yaml   | 41 +++++++++++++++++++
 2 files changed, 41 insertions(+), 16 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml

diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
deleted file mode 100644
index e73358075a90..000000000000
--- a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
+++ /dev/null
@@ -1,16 +0,0 @@
-Device-tree bindings for FSI-attached POWER9/POWER10 On-Chip Controller (OCC)
------------------------------------------------------------------------------
-
-This is the binding for the P9 or P10 On-Chip Controller accessed over FSI from
-a service processor. See fsi.txt for details on bindings for FSI slave and CFAM
-nodes. The OCC is not an FSI slave device itself, rather it is accessed
-through the SBE FIFO.
-
-Required properties:
- - compatible = "ibm,p9-occ" or "ibm,p10-occ"
-
-Examples:
-
-    occ {
-        compatible = "ibm,p9-occ";
-    };
diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
new file mode 100644
index 000000000000..1fa87d452489
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/ibm,p9-occ.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached On-Chip Controller (OCC)
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  The POWER processor On-Chip Controller (OCC) helps manage power and
+  thermals for the system, accessed through the FSI-attached SBEFIFO
+  from a service processor.
+
+properties:
+  compatible:
+    enum:
+      - ibm,p9-occ
+      - ibm,p10-occ
+
+  reg:
+    items:
+      - description: Processor index
+
+required:
+  - compatible
+
+patternProperties:
+  "^occ-hwmon(@.*)?":
+    type: object
+    $ref: /schemas/hwmon/ibm,occ-hwmon.yaml
+
+additionalProperties: false
+
+examples:
+  - |
+    occ {
+        compatible = "ibm,p9-occ";
+    };
-- 
2.39.3

[PATCH v3 04/14] dt-bindings: fsi: p9-occ: Switch to yaml format

[Eddie James]

Switch to yaml for the OCC documentation. Also document the fact
that the OCC "bridge" device will often have the hwmon node as a
child.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/fsi/ibm,p9-occ.txt    | 16 --------
 .../devicetree/bindings/fsi/ibm,p9-occ.yaml   | 41 +++++++++++++++++++
 2 files changed, 41 insertions(+), 16 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml

diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
deleted file mode 100644
index e73358075a90..000000000000
--- a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
+++ /dev/null
@@ -1,16 +0,0 @@
-Device-tree bindings for FSI-attached POWER9/POWER10 On-Chip Controller (OCC)
------------------------------------------------------------------------------
-
-This is the binding for the P9 or P10 On-Chip Controller accessed over FSI from
-a service processor. See fsi.txt for details on bindings for FSI slave and CFAM
-nodes. The OCC is not an FSI slave device itself, rather it is accessed
-through the SBE FIFO.
-
-Required properties:
- - compatible = "ibm,p9-occ" or "ibm,p10-occ"
-
-Examples:
-
-    occ {
-        compatible = "ibm,p9-occ";
-    };
diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
new file mode 100644
index 000000000000..1fa87d452489
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/ibm,p9-occ.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached On-Chip Controller (OCC)
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  The POWER processor On-Chip Controller (OCC) helps manage power and
+  thermals for the system, accessed through the FSI-attached SBEFIFO
+  from a service processor.
+
+properties:
+  compatible:
+    enum:
+      - ibm,p9-occ
+      - ibm,p10-occ
+
+  reg:
+    items:
+      - description: Processor index
+
+required:
+  - compatible
+
+patternProperties:
+  "^occ-hwmon(@.*)?":
+    type: object
+    $ref: /schemas/hwmon/ibm,occ-hwmon.yaml
+
+additionalProperties: false
+
+examples:
+  - |
+    occ {
+        compatible = "ibm,p9-occ";
+    };
-- 
2.39.3

[PATCH v3 04/14] dt-bindings: fsi: p9-occ: Switch to yaml format

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Switch to yaml for the OCC documentation. Also document the fact
> that the OCC "bridge" device will often have the hwmon node as a
> child.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../devicetree/bindings/fsi/ibm,p9-occ.txt    | 16 --------
>  .../devicetree/bindings/fsi/ibm,p9-occ.yaml   | 41 +++++++++++++++++++
>  2 files changed, 41 insertions(+), 16 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
> 
> diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
> deleted file mode 100644
> index e73358075a90..000000000000
> --- a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
> +++ /dev/null
> @@ -1,16 +0,0 @@
> -Device-tree bindings for FSI-attached POWER9/POWER10 On-Chip Controller (OCC)
> ------------------------------------------------------------------------------
> -
> -This is the binding for the P9 or P10 On-Chip Controller accessed over FSI from
> -a service processor. See fsi.txt for details on bindings for FSI slave and CFAM
> -nodes. The OCC is not an FSI slave device itself, rather it is accessed
> -through the SBE FIFO.
> -
> -Required properties:
> - - compatible = "ibm,p9-occ" or "ibm,p10-occ"
> -
> -Examples:
> -
> -    occ {
> -        compatible = "ibm,p9-occ";
> -    };
> diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
> new file mode 100644
> index 000000000000..1fa87d452489
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
> @@ -0,0 +1,41 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/fsi/ibm,p9-occ.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM FSI-attached On-Chip Controller (OCC)
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  The POWER processor On-Chip Controller (OCC) helps manage power and
> +  thermals for the system, accessed through the FSI-attached SBEFIFO
> +  from a service processor.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,p9-occ
> +      - ibm,p10-occ
> +
> +  reg:
> +    items:
> +      - description: Processor index
> +
> +required:
> +  - compatible

required goes after all properties, so below.

> +
> +patternProperties:
> +  "^occ-hwmon(@.*)?":
> +    type: object
> +    $ref: /schemas/hwmon/ibm,occ-hwmon.yaml

Drop occ, not relevant. Why unit address is optional? This is supposed
to be specific. Use proper regex as well for hex numbers.

> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    occ {
> +        compatible = "ibm,p9-occ";

Not complete.


Best regards,
Krzysztof

Re: [PATCH v3 04/14] dt-bindings: fsi: p9-occ: Switch to yaml format

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Switch to yaml for the OCC documentation. Also document the fact
> that the OCC "bridge" device will often have the hwmon node as a
> child.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../devicetree/bindings/fsi/ibm,p9-occ.txt    | 16 --------
>  .../devicetree/bindings/fsi/ibm,p9-occ.yaml   | 41 +++++++++++++++++++
>  2 files changed, 41 insertions(+), 16 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
> 
> diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
> deleted file mode 100644
> index e73358075a90..000000000000
> --- a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
> +++ /dev/null
> @@ -1,16 +0,0 @@
> -Device-tree bindings for FSI-attached POWER9/POWER10 On-Chip Controller (OCC)
> ------------------------------------------------------------------------------
> -
> -This is the binding for the P9 or P10 On-Chip Controller accessed over FSI from
> -a service processor. See fsi.txt for details on bindings for FSI slave and CFAM
> -nodes. The OCC is not an FSI slave device itself, rather it is accessed
> -through the SBE FIFO.
> -
> -Required properties:
> - - compatible = "ibm,p9-occ" or "ibm,p10-occ"
> -
> -Examples:
> -
> -    occ {
> -        compatible = "ibm,p9-occ";
> -    };
> diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
> new file mode 100644
> index 000000000000..1fa87d452489
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
> @@ -0,0 +1,41 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/fsi/ibm,p9-occ.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM FSI-attached On-Chip Controller (OCC)
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  The POWER processor On-Chip Controller (OCC) helps manage power and
> +  thermals for the system, accessed through the FSI-attached SBEFIFO
> +  from a service processor.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,p9-occ
> +      - ibm,p10-occ
> +
> +  reg:
> +    items:
> +      - description: Processor index
> +
> +required:
> +  - compatible

required goes after all properties, so below.

> +
> +patternProperties:
> +  "^occ-hwmon(@.*)?":
> +    type: object
> +    $ref: /schemas/hwmon/ibm,occ-hwmon.yaml

Drop occ, not relevant. Why unit address is optional? This is supposed
to be specific. Use proper regex as well for hex numbers.

> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    occ {
> +        compatible = "ibm,p9-occ";

Not complete.


Best regards,
Krzysztof

[PATCH v3 04/14] dt-bindings: fsi: p9-occ: Switch to yaml format

[Eddie James]

On 4/26/24 01:19, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Switch to yaml for the OCC documentation. Also document the fact
>> that the OCC "bridge" device will often have the hwmon node as a
>> child.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../devicetree/bindings/fsi/ibm,p9-occ.txt    | 16 --------
>>   .../devicetree/bindings/fsi/ibm,p9-occ.yaml   | 41 +++++++++++++++++++
>>   2 files changed, 41 insertions(+), 16 deletions(-)
>>   delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>>   create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>> deleted file mode 100644
>> index e73358075a90..000000000000
>> --- a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>> +++ /dev/null
>> @@ -1,16 +0,0 @@
>> -Device-tree bindings for FSI-attached POWER9/POWER10 On-Chip Controller (OCC)
>> ------------------------------------------------------------------------------
>> -
>> -This is the binding for the P9 or P10 On-Chip Controller accessed over FSI from
>> -a service processor. See fsi.txt for details on bindings for FSI slave and CFAM
>> -nodes. The OCC is not an FSI slave device itself, rather it is accessed
>> -through the SBE FIFO.
>> -
>> -Required properties:
>> - - compatible = "ibm,p9-occ" or "ibm,p10-occ"
>> -
>> -Examples:
>> -
>> -    occ {
>> -        compatible = "ibm,p9-occ";
>> -    };
>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
>> new file mode 100644
>> index 000000000000..1fa87d452489
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
>> @@ -0,0 +1,41 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/fsi/ibm,p9-occ.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM FSI-attached On-Chip Controller (OCC)
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  The POWER processor On-Chip Controller (OCC) helps manage power and
>> +  thermals for the system, accessed through the FSI-attached SBEFIFO
>> +  from a service processor.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,p9-occ
>> +      - ibm,p10-occ
>> +
>> +  reg:
>> +    items:
>> +      - description: Processor index
>> +
>> +required:
>> +  - compatible
> required goes after all properties, so below.


Ack.


>
>> +
>> +patternProperties:
>> +  "^occ-hwmon(@.*)?":
>> +    type: object
>> +    $ref: /schemas/hwmon/ibm,occ-hwmon.yaml
> Drop occ, not relevant. Why unit address is optional? This is supposed
> to be specific. Use proper regex as well for hex numbers.


Well, there isn't really any concept of address here, it's a 1-to-1 
relationship. I should just drop the unit address.


>
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> +  - |
>> +    occ {
>> +        compatible = "ibm,p9-occ";
> Not complete.


Ack.


>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 04/14] dt-bindings: fsi: p9-occ: Switch to yaml format

[Eddie James]

On 4/26/24 01:19, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Switch to yaml for the OCC documentation. Also document the fact
>> that the OCC "bridge" device will often have the hwmon node as a
>> child.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../devicetree/bindings/fsi/ibm,p9-occ.txt    | 16 --------
>>   .../devicetree/bindings/fsi/ibm,p9-occ.yaml   | 41 +++++++++++++++++++
>>   2 files changed, 41 insertions(+), 16 deletions(-)
>>   delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>>   create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>> deleted file mode 100644
>> index e73358075a90..000000000000
>> --- a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>> +++ /dev/null
>> @@ -1,16 +0,0 @@
>> -Device-tree bindings for FSI-attached POWER9/POWER10 On-Chip Controller (OCC)
>> ------------------------------------------------------------------------------
>> -
>> -This is the binding for the P9 or P10 On-Chip Controller accessed over FSI from
>> -a service processor. See fsi.txt for details on bindings for FSI slave and CFAM
>> -nodes. The OCC is not an FSI slave device itself, rather it is accessed
>> -through the SBE FIFO.
>> -
>> -Required properties:
>> - - compatible = "ibm,p9-occ" or "ibm,p10-occ"
>> -
>> -Examples:
>> -
>> -    occ {
>> -        compatible = "ibm,p9-occ";
>> -    };
>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
>> new file mode 100644
>> index 000000000000..1fa87d452489
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
>> @@ -0,0 +1,41 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/fsi/ibm,p9-occ.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM FSI-attached On-Chip Controller (OCC)
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  The POWER processor On-Chip Controller (OCC) helps manage power and
>> +  thermals for the system, accessed through the FSI-attached SBEFIFO
>> +  from a service processor.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,p9-occ
>> +      - ibm,p10-occ
>> +
>> +  reg:
>> +    items:
>> +      - description: Processor index
>> +
>> +required:
>> +  - compatible
> required goes after all properties, so below.


Ack.


>
>> +
>> +patternProperties:
>> +  "^occ-hwmon(@.*)?":
>> +    type: object
>> +    $ref: /schemas/hwmon/ibm,occ-hwmon.yaml
> Drop occ, not relevant. Why unit address is optional? This is supposed
> to be specific. Use proper regex as well for hex numbers.


Well, there isn't really any concept of address here, it's a 1-to-1 
relationship. I should just drop the unit address.


>
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> +  - |
>> +    occ {
>> +        compatible = "ibm,p9-occ";
> Not complete.


Ack.


>
>
> Best regards,
> Krzysztof
>

[PATCH v3 05/14] dt-bindings: fsi: Document the IBM SBEFIFO engine

[Eddie James]

The SBEFIFO engine provides an interface to the POWER processor
Self Boot Engine (SBE).

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
---
Changes since v1:
 - Chance "ody" to "odyssey"
 - Fix typo in commit message
 - Reword description to describe the hardware only

Changes since v2:
 - Rename file
 - Remove '|' after description
 - Change generic node name to match fsi.txt

Changes since sending in the Odyssey SBEFIFO series:
 - Add occ child node documentation

 .../bindings/fsi/ibm,p9-sbefifo.yaml          | 50 +++++++++++++++++++
 1 file changed, 50 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml

diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml b/Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml
new file mode 100644
index 000000000000..72569147db2a
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/ibm,p9-sbefifo.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached SBEFIFO engine
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  The SBEFIFO is an FSI CFAM engine that provides an interface to the
+  POWER processor Self Boot Engine (SBE). This node will always be a child
+  of an FSI CFAM node; see fsi.txt for details on FSI slave and CFAM
+  nodes.
+
+properties:
+  compatible:
+    enum:
+      - ibm,p9-sbefifo
+      - ibm,odyssey-sbefifo
+
+  reg:
+    items:
+      - description: FSI slave address
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "^occ(@.*)?":
+    type: object
+    $ref: ibm,p9-occ.yaml#
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    fsi-slave-engine at 2400 {
+        compatible = "ibm,p9-sbefifo";
+        reg = <0x2400 0x400>;
+    };
-- 
2.39.3

[PATCH v3 05/14] dt-bindings: fsi: Document the IBM SBEFIFO engine

[Eddie James]

The SBEFIFO engine provides an interface to the POWER processor
Self Boot Engine (SBE).

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
---
Changes since v1:
 - Chance "ody" to "odyssey"
 - Fix typo in commit message
 - Reword description to describe the hardware only

Changes since v2:
 - Rename file
 - Remove '|' after description
 - Change generic node name to match fsi.txt

Changes since sending in the Odyssey SBEFIFO series:
 - Add occ child node documentation

 .../bindings/fsi/ibm,p9-sbefifo.yaml          | 50 +++++++++++++++++++
 1 file changed, 50 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml

diff --git a/Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml b/Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml
new file mode 100644
index 000000000000..72569147db2a
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/ibm,p9-sbefifo.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached SBEFIFO engine
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  The SBEFIFO is an FSI CFAM engine that provides an interface to the
+  POWER processor Self Boot Engine (SBE). This node will always be a child
+  of an FSI CFAM node; see fsi.txt for details on FSI slave and CFAM
+  nodes.
+
+properties:
+  compatible:
+    enum:
+      - ibm,p9-sbefifo
+      - ibm,odyssey-sbefifo
+
+  reg:
+    items:
+      - description: FSI slave address
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "^occ(@.*)?":
+    type: object
+    $ref: ibm,p9-occ.yaml#
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    fsi-slave-engine@2400 {
+        compatible = "ibm,p9-sbefifo";
+        reg = <0x2400 0x400>;
+    };
-- 
2.39.3

[PATCH v3 05/14] dt-bindings: fsi: Document the IBM SBEFIFO engine

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> The SBEFIFO engine provides an interface to the POWER processor
> Self Boot Engine (SBE).
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
> ---


> +description:
> +  The SBEFIFO is an FSI CFAM engine that provides an interface to the
> +  POWER processor Self Boot Engine (SBE). This node will always be a child
> +  of an FSI CFAM node; see fsi.txt for details on FSI slave and CFAM
> +  nodes.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,p9-sbefifo
> +      - ibm,odyssey-sbefifo
> +
> +  reg:
> +    items:
> +      - description: FSI slave address
> +
> +  "#address-cells":
> +    const: 1
> +
> +  "#size-cells":
> +    const: 0
> +
> +patternProperties:
> +  "^occ(@.*)?":

Why unit address is optional?



Best regards,
Krzysztof

Re: [PATCH v3 05/14] dt-bindings: fsi: Document the IBM SBEFIFO engine

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> The SBEFIFO engine provides an interface to the POWER processor
> Self Boot Engine (SBE).
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
> ---


> +description:
> +  The SBEFIFO is an FSI CFAM engine that provides an interface to the
> +  POWER processor Self Boot Engine (SBE). This node will always be a child
> +  of an FSI CFAM node; see fsi.txt for details on FSI slave and CFAM
> +  nodes.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,p9-sbefifo
> +      - ibm,odyssey-sbefifo
> +
> +  reg:
> +    items:
> +      - description: FSI slave address
> +
> +  "#address-cells":
> +    const: 1
> +
> +  "#size-cells":
> +    const: 0
> +
> +patternProperties:
> +  "^occ(@.*)?":

Why unit address is optional?



Best regards,
Krzysztof

[PATCH v3 05/14] dt-bindings: fsi: Document the IBM SBEFIFO engine

[Eddie James]

On 4/26/24 01:20, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> The SBEFIFO engine provides an interface to the POWER processor
>> Self Boot Engine (SBE).
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> Acked-by: Conor Dooley <conor.dooley@microchip.com>
>> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
>> ---
>
>> +description:
>> +  The SBEFIFO is an FSI CFAM engine that provides an interface to the
>> +  POWER processor Self Boot Engine (SBE). This node will always be a child
>> +  of an FSI CFAM node; see fsi.txt for details on FSI slave and CFAM
>> +  nodes.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,p9-sbefifo
>> +      - ibm,odyssey-sbefifo
>> +
>> +  reg:
>> +    items:
>> +      - description: FSI slave address
>> +
>> +  "#address-cells":
>> +    const: 1
>> +
>> +  "#size-cells":
>> +    const: 0
>> +
>> +patternProperties:
>> +  "^occ(@.*)?":
> Why unit address is optional?


In this case, it's because we use the reg property (reflecting the unit 
address) to indicate the processor index of the occ node. However I 
think I should drop the unit address here, it's meaningless, there is no 
addressing for the OCC from the SBEFIFO.


>
>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 05/14] dt-bindings: fsi: Document the IBM SBEFIFO engine

[Eddie James]

On 4/26/24 01:20, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> The SBEFIFO engine provides an interface to the POWER processor
>> Self Boot Engine (SBE).
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> Acked-by: Conor Dooley <conor.dooley@microchip.com>
>> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
>> ---
>
>> +description:
>> +  The SBEFIFO is an FSI CFAM engine that provides an interface to the
>> +  POWER processor Self Boot Engine (SBE). This node will always be a child
>> +  of an FSI CFAM node; see fsi.txt for details on FSI slave and CFAM
>> +  nodes.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,p9-sbefifo
>> +      - ibm,odyssey-sbefifo
>> +
>> +  reg:
>> +    items:
>> +      - description: FSI slave address
>> +
>> +  "#address-cells":
>> +    const: 1
>> +
>> +  "#size-cells":
>> +    const: 0
>> +
>> +patternProperties:
>> +  "^occ(@.*)?":
> Why unit address is optional?


In this case, it's because we use the reg property (reflecting the unit 
address) to indicate the processor index of the occ node. However I 
think I should drop the unit address here, it's meaningless, there is no 
addressing for the OCC from the SBEFIFO.


>
>
>
> Best regards,
> Krzysztof
>

[PATCH v3 06/14] dt-bindings: fsi: Document the FSI controller common properties

[Eddie James]

Since there are multiple FSI controllers documented, the common
properties should be documented separately and then referenced
from the specific controller documentation.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../bindings/fsi/fsi-controller.yaml          | 65 +++++++++++++++++++
 1 file changed, 65 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fsi/fsi-controller.yaml

diff --git a/Documentation/devicetree/bindings/fsi/fsi-controller.yaml b/Documentation/devicetree/bindings/fsi/fsi-controller.yaml
new file mode 100644
index 000000000000..9e917295996d
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/fsi-controller.yaml
@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/fsi-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: FSI Controller Common Properties
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  FSI (FRU (Field Replaceable Unit) Service Interface) is a two wire bus. The
+  FSI bus is connected to a CFAM (Common FRU Access Macro) which contains
+  various engines such as I2C controllers, SPI controllers, etc.
+
+properties:
+  "#address-cells":
+    const: 2
+
+  "#size-cells":
+    const: 0
+
+  no-scan-on-init:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The FSI controller cannot scan the bus during initialization.
+
+patternProperties:
+  "cfam@[0-9a-f],[0-9a-f]":
+    type: object
+    properties:
+      chip-id:
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+      reg:
+        maxItems: 1
+
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 1
+
+    required:
+      - reg
+
+    additionalProperties: true
+
+additionalProperties: true
+
+examples:
+  - |
+    fsi at 3400 {
+        #address-cells = <2>;
+        #size-cells = <0>;
+        compatible = "fsi-controller";
+        reg = <0x3400 0x400>;
+
+        cfam at 0,0 {
+            #address-cells = <1>;
+            #size-cells = <1>;
+            reg = <0 0>;
+        };
+    };
-- 
2.39.3

[PATCH v3 06/14] dt-bindings: fsi: Document the FSI controller common properties

[Eddie James]

Since there are multiple FSI controllers documented, the common
properties should be documented separately and then referenced
from the specific controller documentation.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../bindings/fsi/fsi-controller.yaml          | 65 +++++++++++++++++++
 1 file changed, 65 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fsi/fsi-controller.yaml

diff --git a/Documentation/devicetree/bindings/fsi/fsi-controller.yaml b/Documentation/devicetree/bindings/fsi/fsi-controller.yaml
new file mode 100644
index 000000000000..9e917295996d
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/fsi-controller.yaml
@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/fsi-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: FSI Controller Common Properties
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  FSI (FRU (Field Replaceable Unit) Service Interface) is a two wire bus. The
+  FSI bus is connected to a CFAM (Common FRU Access Macro) which contains
+  various engines such as I2C controllers, SPI controllers, etc.
+
+properties:
+  "#address-cells":
+    const: 2
+
+  "#size-cells":
+    const: 0
+
+  no-scan-on-init:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The FSI controller cannot scan the bus during initialization.
+
+patternProperties:
+  "cfam@[0-9a-f],[0-9a-f]":
+    type: object
+    properties:
+      chip-id:
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+      reg:
+        maxItems: 1
+
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 1
+
+    required:
+      - reg
+
+    additionalProperties: true
+
+additionalProperties: true
+
+examples:
+  - |
+    fsi@3400 {
+        #address-cells = <2>;
+        #size-cells = <0>;
+        compatible = "fsi-controller";
+        reg = <0x3400 0x400>;
+
+        cfam@0,0 {
+            #address-cells = <1>;
+            #size-cells = <1>;
+            reg = <0 0>;
+        };
+    };
-- 
2.39.3

[PATCH v3 06/14] dt-bindings: fsi: Document the FSI controller common properties

[Rob Herring]

On Thu, 25 Apr 2024 16:36:53 -0500, Eddie James wrote:
> Since there are multiple FSI controllers documented, the common
> properties should be documented separately and then referenced
> from the specific controller documentation.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../bindings/fsi/fsi-controller.yaml          | 65 +++++++++++++++++++
>  1 file changed, 65 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fsi/fsi-controller.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/fsi/fsi-controller.example.dtb: /example-0/fsi at 3400: failed to match any schema with compatible: ['fsi-controller']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240425213701.655540-7-eajames at linux.ibm.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v3 06/14] dt-bindings: fsi: Document the FSI controller common properties

[Rob Herring]

On Thu, 25 Apr 2024 16:36:53 -0500, Eddie James wrote:
> Since there are multiple FSI controllers documented, the common
> properties should be documented separately and then referenced
> from the specific controller documentation.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../bindings/fsi/fsi-controller.yaml          | 65 +++++++++++++++++++
>  1 file changed, 65 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fsi/fsi-controller.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/fsi/fsi-controller.example.dtb: /example-0/fsi@3400: failed to match any schema with compatible: ['fsi-controller']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240425213701.655540-7-eajames@linux.ibm.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

[PATCH v3 06/14] dt-bindings: fsi: Document the FSI controller common properties

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Since there are multiple FSI controllers documented, the common
> properties should be documented separately and then referenced
> from the specific controller documentation.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---


> +
> +  no-scan-on-init:
> +    $ref: /schemas/types.yaml#/definitions/flag
> +    description:
> +      The FSI controller cannot scan the bus during initialization.
> +
> +patternProperties:
> +  "cfam@[0-9a-f],[0-9a-f]":
> +    type: object
> +    properties:
> +      chip-id:
> +        $ref: /schemas/types.yaml#/definitions/uint32

Missing description

> +
> +      reg:
> +        maxItems: 1
> +
> +      "#address-cells":
> +        const: 1
> +
> +      "#size-cells":
> +        const: 1
> +
> +    required:
> +      - reg
> +
> +    additionalProperties: true> +
> +additionalProperties: true
> +
> +examples:
> +  - |
> +    fsi at 3400 {
> +        #address-cells = <2>;
> +        #size-cells = <0>;
> +        compatible = "fsi-controller";

No, there is no such compatible here.

> +        reg = <0x3400 0x400>;

Neither reg.

Also, keep order of properties matching DTS coding style.


Best regards,
Krzysztof

Re: [PATCH v3 06/14] dt-bindings: fsi: Document the FSI controller common properties

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Since there are multiple FSI controllers documented, the common
> properties should be documented separately and then referenced
> from the specific controller documentation.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---


> +
> +  no-scan-on-init:
> +    $ref: /schemas/types.yaml#/definitions/flag
> +    description:
> +      The FSI controller cannot scan the bus during initialization.
> +
> +patternProperties:
> +  "cfam@[0-9a-f],[0-9a-f]":
> +    type: object
> +    properties:
> +      chip-id:
> +        $ref: /schemas/types.yaml#/definitions/uint32

Missing description

> +
> +      reg:
> +        maxItems: 1
> +
> +      "#address-cells":
> +        const: 1
> +
> +      "#size-cells":
> +        const: 1
> +
> +    required:
> +      - reg
> +
> +    additionalProperties: true> +
> +additionalProperties: true
> +
> +examples:
> +  - |
> +    fsi@3400 {
> +        #address-cells = <2>;
> +        #size-cells = <0>;
> +        compatible = "fsi-controller";

No, there is no such compatible here.

> +        reg = <0x3400 0x400>;

Neither reg.

Also, keep order of properties matching DTS coding style.


Best regards,
Krzysztof

[PATCH v3 06/14] dt-bindings: fsi: Document the FSI controller common properties

[Eddie James]

On 4/26/24 01:23, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Since there are multiple FSI controllers documented, the common
>> properties should be documented separately and then referenced
>> from the specific controller documentation.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>
>> +
>> +  no-scan-on-init:
>> +    $ref: /schemas/types.yaml#/definitions/flag
>> +    description:
>> +      The FSI controller cannot scan the bus during initialization.
>> +
>> +patternProperties:
>> +  "cfam@[0-9a-f],[0-9a-f]":
>> +    type: object
>> +    properties:
>> +      chip-id:
>> +        $ref: /schemas/types.yaml#/definitions/uint32
> Missing description


Ack'd, and comments below


>
>> +
>> +      reg:
>> +        maxItems: 1
>> +
>> +      "#address-cells":
>> +        const: 1
>> +
>> +      "#size-cells":
>> +        const: 1
>> +
>> +    required:
>> +      - reg
>> +
>> +    additionalProperties: true> +
>> +additionalProperties: true
>> +
>> +examples:
>> +  - |
>> +    fsi at 3400 {
>> +        #address-cells = <2>;
>> +        #size-cells = <0>;
>> +        compatible = "fsi-controller";
> No, there is no such compatible here.
>
>> +        reg = <0x3400 0x400>;
> Neither reg.
>
> Also, keep order of properties matching DTS coding style.
>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 06/14] dt-bindings: fsi: Document the FSI controller common properties

[Eddie James]

On 4/26/24 01:23, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Since there are multiple FSI controllers documented, the common
>> properties should be documented separately and then referenced
>> from the specific controller documentation.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>
>> +
>> +  no-scan-on-init:
>> +    $ref: /schemas/types.yaml#/definitions/flag
>> +    description:
>> +      The FSI controller cannot scan the bus during initialization.
>> +
>> +patternProperties:
>> +  "cfam@[0-9a-f],[0-9a-f]":
>> +    type: object
>> +    properties:
>> +      chip-id:
>> +        $ref: /schemas/types.yaml#/definitions/uint32
> Missing description


Ack'd, and comments below


>
>> +
>> +      reg:
>> +        maxItems: 1
>> +
>> +      "#address-cells":
>> +        const: 1
>> +
>> +      "#size-cells":
>> +        const: 1
>> +
>> +    required:
>> +      - reg
>> +
>> +    additionalProperties: true> +
>> +additionalProperties: true
>> +
>> +examples:
>> +  - |
>> +    fsi@3400 {
>> +        #address-cells = <2>;
>> +        #size-cells = <0>;
>> +        compatible = "fsi-controller";
> No, there is no such compatible here.
>
>> +        reg = <0x3400 0x400>;
> Neither reg.
>
> Also, keep order of properties matching DTS coding style.
>
>
> Best regards,
> Krzysztof
>

[PATCH v3 07/14] dt-bindings: fsi: ibm,i2cr-fsi-master: Reference common FSI controller

[Eddie James]

Remove the common properties from the I2CR documentation and instead
point to the common FSI controller documentation.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml         | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml
index 442cecdc57cb..9f0c72e8c1a6 100644
--- a/Documentation/devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml
+++ b/Documentation/devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml
@@ -22,11 +22,14 @@ properties:
   reg:
     maxItems: 1
 
+allOf:
+  - $ref: fsi-controller.yaml#
+
 required:
   - compatible
   - reg
 
-additionalProperties: false
+unevaluatedProperties: false
 
 examples:
   - |
-- 
2.39.3

[PATCH v3 07/14] dt-bindings: fsi: ibm,i2cr-fsi-master: Reference common FSI controller

[Eddie James]

Remove the common properties from the I2CR documentation and instead
point to the common FSI controller documentation.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml         | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml
index 442cecdc57cb..9f0c72e8c1a6 100644
--- a/Documentation/devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml
+++ b/Documentation/devicetree/bindings/fsi/ibm,i2cr-fsi-master.yaml
@@ -22,11 +22,14 @@ properties:
   reg:
     maxItems: 1
 
+allOf:
+  - $ref: fsi-controller.yaml#
+
 required:
   - compatible
   - reg
 
-additionalProperties: false
+unevaluatedProperties: false
 
 examples:
   - |
-- 
2.39.3

[PATCH v3 08/14] dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format

[Eddie James]

Switch to yaml for the AST2600 FSI master documentation.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../fsi/aspeed,ast2600-fsi-master.yaml        | 72 +++++++++++++++++++
 .../bindings/fsi/fsi-master-aspeed.txt        | 36 ----------
 2 files changed, 72 insertions(+), 36 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
 delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt

diff --git a/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
new file mode 100644
index 000000000000..f053e3e1d259
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Aspeed FSI master
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  The AST2600 and later contain two identical FSI masters. They share a
+  clock and have a separate interrupt line and output pins.
+
+properties:
+  compatible:
+    enum:
+      - "aspeed,ast2600-fsi-master"
+      - "aspeed,ast2700-fsi-master"
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  cfam-reset-gpios:
+    maxItems: 1
+    description:
+      Output GPIO pin for CFAM reset
+
+  fsi-routing-gpios:
+    maxItems: 1
+    description:
+      Output GPIO pin for setting the FSI mux (internal or cabled)
+
+  fsi-mux-gpios:
+    maxItems: 1
+    description:
+      Input GPIO pin for detecting the desired FSI mux state
+
+  interrupts:
+    maxItems: 1
+
+allOf:
+  - $ref: fsi-controller.yaml#
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/ast2600-clock.h>
+    #include <dt-bindings/gpio/aspeed-gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    fsi-master at 1e79b000 {
+        compatible = "aspeed,ast2600-fsi-master";
+        reg = <0x1e79b000 0x94>;
+        interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_fsi1_default>;
+        clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
+        fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
+        fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
+        cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+    };
diff --git a/Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt b/Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
deleted file mode 100644
index 9853fefff5d8..000000000000
--- a/Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
+++ /dev/null
@@ -1,36 +0,0 @@
-Device-tree bindings for AST2600 FSI master
--------------------------------------------
-
-The AST2600 contains two identical FSI masters. They share a clock and have a
-separate interrupt line and output pins.
-
-Required properties:
- - compatible: "aspeed,ast2600-fsi-master"
- - reg: base address and length
- - clocks: phandle and clock number
- - interrupts: platform dependent interrupt description
- - pinctrl-0: phandle to pinctrl node
- - pinctrl-names: pinctrl state
-
-Optional properties:
- - cfam-reset-gpios: GPIO for CFAM reset
-
- - fsi-routing-gpios: GPIO for setting the FSI mux (internal or cabled)
- - fsi-mux-gpios: GPIO for detecting the desired FSI mux state
-
-
-Examples:
-
-    fsi-master {
-        compatible = "aspeed,ast2600-fsi-master", "fsi-master";
-        reg = <0x1e79b000 0x94>;
-	interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fsi1_default>;
-	clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
-
-	fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
-	fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
-
-	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
-    };
-- 
2.39.3

[PATCH v3 08/14] dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format

[Eddie James]

Switch to yaml for the AST2600 FSI master documentation.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../fsi/aspeed,ast2600-fsi-master.yaml        | 72 +++++++++++++++++++
 .../bindings/fsi/fsi-master-aspeed.txt        | 36 ----------
 2 files changed, 72 insertions(+), 36 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
 delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt

diff --git a/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
new file mode 100644
index 000000000000..f053e3e1d259
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Aspeed FSI master
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  The AST2600 and later contain two identical FSI masters. They share a
+  clock and have a separate interrupt line and output pins.
+
+properties:
+  compatible:
+    enum:
+      - "aspeed,ast2600-fsi-master"
+      - "aspeed,ast2700-fsi-master"
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  cfam-reset-gpios:
+    maxItems: 1
+    description:
+      Output GPIO pin for CFAM reset
+
+  fsi-routing-gpios:
+    maxItems: 1
+    description:
+      Output GPIO pin for setting the FSI mux (internal or cabled)
+
+  fsi-mux-gpios:
+    maxItems: 1
+    description:
+      Input GPIO pin for detecting the desired FSI mux state
+
+  interrupts:
+    maxItems: 1
+
+allOf:
+  - $ref: fsi-controller.yaml#
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/ast2600-clock.h>
+    #include <dt-bindings/gpio/aspeed-gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    fsi-master@1e79b000 {
+        compatible = "aspeed,ast2600-fsi-master";
+        reg = <0x1e79b000 0x94>;
+        interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_fsi1_default>;
+        clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
+        fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
+        fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
+        cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+    };
diff --git a/Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt b/Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
deleted file mode 100644
index 9853fefff5d8..000000000000
--- a/Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
+++ /dev/null
@@ -1,36 +0,0 @@
-Device-tree bindings for AST2600 FSI master
--------------------------------------------
-
-The AST2600 contains two identical FSI masters. They share a clock and have a
-separate interrupt line and output pins.
-
-Required properties:
- - compatible: "aspeed,ast2600-fsi-master"
- - reg: base address and length
- - clocks: phandle and clock number
- - interrupts: platform dependent interrupt description
- - pinctrl-0: phandle to pinctrl node
- - pinctrl-names: pinctrl state
-
-Optional properties:
- - cfam-reset-gpios: GPIO for CFAM reset
-
- - fsi-routing-gpios: GPIO for setting the FSI mux (internal or cabled)
- - fsi-mux-gpios: GPIO for detecting the desired FSI mux state
-
-
-Examples:
-
-    fsi-master {
-        compatible = "aspeed,ast2600-fsi-master", "fsi-master";
-        reg = <0x1e79b000 0x94>;
-	interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fsi1_default>;
-	clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
-
-	fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
-	fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
-
-	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
-    };
-- 
2.39.3

[PATCH v3 08/14] dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Switch to yaml for the AST2600 FSI master documentation.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../fsi/aspeed,ast2600-fsi-master.yaml        | 72 +++++++++++++++++++
>  .../bindings/fsi/fsi-master-aspeed.txt        | 36 ----------
>  2 files changed, 72 insertions(+), 36 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>  delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
> 
> diff --git a/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> new file mode 100644
> index 000000000000..f053e3e1d259
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> @@ -0,0 +1,72 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Aspeed FSI master
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  The AST2600 and later contain two identical FSI masters. They share a
> +  clock and have a separate interrupt line and output pins.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - "aspeed,ast2600-fsi-master"
> +      - "aspeed,ast2700-fsi-master"

This wasn't tested. No quotes. Do you see any other example like this?

> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  cfam-reset-gpios:
> +    maxItems: 1
> +    description:
> +      Output GPIO pin for CFAM reset
> +
> +  fsi-routing-gpios:
> +    maxItems: 1
> +    description:
> +      Output GPIO pin for setting the FSI mux (internal or cabled)
> +
> +  fsi-mux-gpios:
> +    maxItems: 1
> +    description:
> +      Input GPIO pin for detecting the desired FSI mux state
> +
> +  interrupts:
> +    maxItems: 1
> +
> +allOf:
> +  - $ref: fsi-controller.yaml#

This goes after required:

> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - interrupts
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/ast2600-clock.h>
> +    #include <dt-bindings/gpio/aspeed-gpio.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    fsi-master at 1e79b000 {
> +        compatible = "aspeed,ast2600-fsi-master";
> +        reg = <0x1e79b000 0x94>;
> +        interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&pinctrl_fsi1_default>;
> +        clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
> +        fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
> +        fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
> +        cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_LOW>;

No children?


Best regards,
Krzysztof

Re: [PATCH v3 08/14] dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Switch to yaml for the AST2600 FSI master documentation.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../fsi/aspeed,ast2600-fsi-master.yaml        | 72 +++++++++++++++++++
>  .../bindings/fsi/fsi-master-aspeed.txt        | 36 ----------
>  2 files changed, 72 insertions(+), 36 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>  delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
> 
> diff --git a/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> new file mode 100644
> index 000000000000..f053e3e1d259
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> @@ -0,0 +1,72 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Aspeed FSI master
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  The AST2600 and later contain two identical FSI masters. They share a
> +  clock and have a separate interrupt line and output pins.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - "aspeed,ast2600-fsi-master"
> +      - "aspeed,ast2700-fsi-master"

This wasn't tested. No quotes. Do you see any other example like this?

> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  cfam-reset-gpios:
> +    maxItems: 1
> +    description:
> +      Output GPIO pin for CFAM reset
> +
> +  fsi-routing-gpios:
> +    maxItems: 1
> +    description:
> +      Output GPIO pin for setting the FSI mux (internal or cabled)
> +
> +  fsi-mux-gpios:
> +    maxItems: 1
> +    description:
> +      Input GPIO pin for detecting the desired FSI mux state
> +
> +  interrupts:
> +    maxItems: 1
> +
> +allOf:
> +  - $ref: fsi-controller.yaml#

This goes after required:

> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - interrupts
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/ast2600-clock.h>
> +    #include <dt-bindings/gpio/aspeed-gpio.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    fsi-master@1e79b000 {
> +        compatible = "aspeed,ast2600-fsi-master";
> +        reg = <0x1e79b000 0x94>;
> +        interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&pinctrl_fsi1_default>;
> +        clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
> +        fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
> +        fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
> +        cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_LOW>;

No children?


Best regards,
Krzysztof

[PATCH v3 08/14] dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format

[Eddie James]

On 4/26/24 01:25, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Switch to yaml for the AST2600 FSI master documentation.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../fsi/aspeed,ast2600-fsi-master.yaml        | 72 +++++++++++++++++++
>>   .../bindings/fsi/fsi-master-aspeed.txt        | 36 ----------
>>   2 files changed, 72 insertions(+), 36 deletions(-)
>>   create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>>   delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
>>
>> diff --git a/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>> new file mode 100644
>> index 000000000000..f053e3e1d259
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>> @@ -0,0 +1,72 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Aspeed FSI master
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  The AST2600 and later contain two identical FSI masters. They share a
>> +  clock and have a separate interrupt line and output pins.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - "aspeed,ast2600-fsi-master"
>> +      - "aspeed,ast2700-fsi-master"
> This wasn't tested. No quotes. Do you see any other example like this?


Strangely this passes make dt_binding_check for me... And Rob's bot 
didn't seem to catch it either. Just an oversight, I'll fix it.


>
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  cfam-reset-gpios:
>> +    maxItems: 1
>> +    description:
>> +      Output GPIO pin for CFAM reset
>> +
>> +  fsi-routing-gpios:
>> +    maxItems: 1
>> +    description:
>> +      Output GPIO pin for setting the FSI mux (internal or cabled)
>> +
>> +  fsi-mux-gpios:
>> +    maxItems: 1
>> +    description:
>> +      Input GPIO pin for detecting the desired FSI mux state
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +allOf:
>> +  - $ref: fsi-controller.yaml#
> This goes after required:


Ack.


>
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - clocks
>> +  - interrupts
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    #include <dt-bindings/clock/ast2600-clock.h>
>> +    #include <dt-bindings/gpio/aspeed-gpio.h>
>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
>> +    fsi-master at 1e79b000 {
>> +        compatible = "aspeed,ast2600-fsi-master";
>> +        reg = <0x1e79b000 0x94>;
>> +        interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&pinctrl_fsi1_default>;
>> +        clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
>> +        fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
>> +        fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
>> +        cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
> No children?


Ack, I'll add one.


>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 08/14] dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format

[Eddie James]

On 4/26/24 01:25, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Switch to yaml for the AST2600 FSI master documentation.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../fsi/aspeed,ast2600-fsi-master.yaml        | 72 +++++++++++++++++++
>>   .../bindings/fsi/fsi-master-aspeed.txt        | 36 ----------
>>   2 files changed, 72 insertions(+), 36 deletions(-)
>>   create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>>   delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
>>
>> diff --git a/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>> new file mode 100644
>> index 000000000000..f053e3e1d259
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>> @@ -0,0 +1,72 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Aspeed FSI master
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  The AST2600 and later contain two identical FSI masters. They share a
>> +  clock and have a separate interrupt line and output pins.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - "aspeed,ast2600-fsi-master"
>> +      - "aspeed,ast2700-fsi-master"
> This wasn't tested. No quotes. Do you see any other example like this?


Strangely this passes make dt_binding_check for me... And Rob's bot 
didn't seem to catch it either. Just an oversight, I'll fix it.


>
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  cfam-reset-gpios:
>> +    maxItems: 1
>> +    description:
>> +      Output GPIO pin for CFAM reset
>> +
>> +  fsi-routing-gpios:
>> +    maxItems: 1
>> +    description:
>> +      Output GPIO pin for setting the FSI mux (internal or cabled)
>> +
>> +  fsi-mux-gpios:
>> +    maxItems: 1
>> +    description:
>> +      Input GPIO pin for detecting the desired FSI mux state
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +allOf:
>> +  - $ref: fsi-controller.yaml#
> This goes after required:


Ack.


>
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - clocks
>> +  - interrupts
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    #include <dt-bindings/clock/ast2600-clock.h>
>> +    #include <dt-bindings/gpio/aspeed-gpio.h>
>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
>> +    fsi-master@1e79b000 {
>> +        compatible = "aspeed,ast2600-fsi-master";
>> +        reg = <0x1e79b000 0x94>;
>> +        interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&pinctrl_fsi1_default>;
>> +        clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
>> +        fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
>> +        fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
>> +        cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
> No children?


Ack, I'll add one.


>
>
> Best regards,
> Krzysztof
>

[PATCH v3 08/14] dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format

[Rob Herring]

On Fri, Apr 26, 2024 at 10:13:52AM -0500, Eddie James wrote:
> 
> On 4/26/24 01:25, Krzysztof Kozlowski wrote:
> > On 25/04/2024 23:36, Eddie James wrote:
> > > Switch to yaml for the AST2600 FSI master documentation.
> > > 
> > > Signed-off-by: Eddie James <eajames@linux.ibm.com>
> > > ---
> > >   .../fsi/aspeed,ast2600-fsi-master.yaml        | 72 +++++++++++++++++++
> > >   .../bindings/fsi/fsi-master-aspeed.txt        | 36 ----------
> > >   2 files changed, 72 insertions(+), 36 deletions(-)
> > >   create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> > >   delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
> > > 
> > > diff --git a/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> > > new file mode 100644
> > > index 000000000000..f053e3e1d259
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> > > @@ -0,0 +1,72 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: Aspeed FSI master
> > > +
> > > +maintainers:
> > > +  - Eddie James <eajames@linux.ibm.com>
> > > +
> > > +description:
> > > +  The AST2600 and later contain two identical FSI masters. They share a
> > > +  clock and have a separate interrupt line and output pins.
> > > +
> > > +properties:
> > > +  compatible:
> > > +    enum:
> > > +      - "aspeed,ast2600-fsi-master"
> > > +      - "aspeed,ast2700-fsi-master"
> > This wasn't tested. No quotes. Do you see any other example like this?
> 
> 
> Strangely this passes make dt_binding_check for me... And Rob's bot didn't
> seem to catch it either. Just an oversight, I'll fix it.

Disabled due to yamllint bug. The fix is now released, so that reminds 
me to go enable it.

Rob

Re: [PATCH v3 08/14] dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format

[Rob Herring]

On Fri, Apr 26, 2024 at 10:13:52AM -0500, Eddie James wrote:
> 
> On 4/26/24 01:25, Krzysztof Kozlowski wrote:
> > On 25/04/2024 23:36, Eddie James wrote:
> > > Switch to yaml for the AST2600 FSI master documentation.
> > > 
> > > Signed-off-by: Eddie James <eajames@linux.ibm.com>
> > > ---
> > >   .../fsi/aspeed,ast2600-fsi-master.yaml        | 72 +++++++++++++++++++
> > >   .../bindings/fsi/fsi-master-aspeed.txt        | 36 ----------
> > >   2 files changed, 72 insertions(+), 36 deletions(-)
> > >   create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> > >   delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
> > > 
> > > diff --git a/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> > > new file mode 100644
> > > index 000000000000..f053e3e1d259
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
> > > @@ -0,0 +1,72 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: Aspeed FSI master
> > > +
> > > +maintainers:
> > > +  - Eddie James <eajames@linux.ibm.com>
> > > +
> > > +description:
> > > +  The AST2600 and later contain two identical FSI masters. They share a
> > > +  clock and have a separate interrupt line and output pins.
> > > +
> > > +properties:
> > > +  compatible:
> > > +    enum:
> > > +      - "aspeed,ast2600-fsi-master"
> > > +      - "aspeed,ast2700-fsi-master"
> > This wasn't tested. No quotes. Do you see any other example like this?
> 
> 
> Strangely this passes make dt_binding_check for me... And Rob's bot didn't
> seem to catch it either. Just an oversight, I'll fix it.

Disabled due to yamllint bug. The fix is now released, so that reminds 
me to go enable it.

Rob

[PATCH v3 09/14] dt-bindings: fsi: Document the FSI Hub Controller

[Eddie James]

Document the FSI Hub Controller CFAM engine.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../bindings/fsi/ibm,hub-fsi-controller.yaml  | 44 +++++++++++++++++++
 1 file changed, 44 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml

diff --git a/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
new file mode 100644
index 000000000000..d96d777d4d9f
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/ibm,hub-fsi-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached FSI Hub Controller
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description: |
+  The FSI Hub Controller is an FSI controller, providing a number of FSI links,
+  located on a CFAM. Therefore this node will always be a child of an FSI CFAM
+  node.
+
+properties:
+  compatible:
+    enum:
+      - ibm,hub-fsi-controller
+
+  reg:
+    items:
+      - description: FSI slave address
+
+allOf:
+  - $ref: fsi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+   fsi at 3400 {
+        #address-cells = <2>;
+        #size-cells = <0>;
+        compatible = "ibm,hub-fsi-controller";
+        reg = <0x3400 0x400>;
+
+        cfam at 0,0 {
+            #address-cells = <1>;
+            #size-cells = <1>;
+            reg = <0 0>;
+        };
+    };
-- 
2.39.3

[PATCH v3 09/14] dt-bindings: fsi: Document the FSI Hub Controller

[Eddie James]

Document the FSI Hub Controller CFAM engine.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../bindings/fsi/ibm,hub-fsi-controller.yaml  | 44 +++++++++++++++++++
 1 file changed, 44 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml

diff --git a/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
new file mode 100644
index 000000000000..d96d777d4d9f
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fsi/ibm,hub-fsi-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached FSI Hub Controller
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description: |
+  The FSI Hub Controller is an FSI controller, providing a number of FSI links,
+  located on a CFAM. Therefore this node will always be a child of an FSI CFAM
+  node.
+
+properties:
+  compatible:
+    enum:
+      - ibm,hub-fsi-controller
+
+  reg:
+    items:
+      - description: FSI slave address
+
+allOf:
+  - $ref: fsi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+   fsi@3400 {
+        #address-cells = <2>;
+        #size-cells = <0>;
+        compatible = "ibm,hub-fsi-controller";
+        reg = <0x3400 0x400>;
+
+        cfam@0,0 {
+            #address-cells = <1>;
+            #size-cells = <1>;
+            reg = <0 0>;
+        };
+    };
-- 
2.39.3

[PATCH v3 09/14] dt-bindings: fsi: Document the FSI Hub Controller

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Document the FSI Hub Controller CFAM engine.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../bindings/fsi/ibm,hub-fsi-controller.yaml  | 44 +++++++++++++++++++
>  1 file changed, 44 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
> 
> diff --git a/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
> new file mode 100644
> index 000000000000..d96d777d4d9f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
> @@ -0,0 +1,44 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/fsi/ibm,hub-fsi-controller.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM FSI-attached FSI Hub Controller
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description: |

Do not need '|' unless you need to preserve formatting.

> +  The FSI Hub Controller is an FSI controller, providing a number of FSI links,
> +  located on a CFAM. Therefore this node will always be a child of an FSI CFAM
> +  node.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,hub-fsi-controller

Again, is it for specific chip? SoC? Aren't you using generic
compatibles (not allowed)?



Best regards,
Krzysztof

Re: [PATCH v3 09/14] dt-bindings: fsi: Document the FSI Hub Controller

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Document the FSI Hub Controller CFAM engine.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../bindings/fsi/ibm,hub-fsi-controller.yaml  | 44 +++++++++++++++++++
>  1 file changed, 44 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
> 
> diff --git a/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
> new file mode 100644
> index 000000000000..d96d777d4d9f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
> @@ -0,0 +1,44 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/fsi/ibm,hub-fsi-controller.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM FSI-attached FSI Hub Controller
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description: |

Do not need '|' unless you need to preserve formatting.

> +  The FSI Hub Controller is an FSI controller, providing a number of FSI links,
> +  located on a CFAM. Therefore this node will always be a child of an FSI CFAM
> +  node.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,hub-fsi-controller

Again, is it for specific chip? SoC? Aren't you using generic
compatibles (not allowed)?



Best regards,
Krzysztof

[PATCH v3 09/14] dt-bindings: fsi: Document the FSI Hub Controller

[Eddie James]

On 4/26/24 01:26, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Document the FSI Hub Controller CFAM engine.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../bindings/fsi/ibm,hub-fsi-controller.yaml  | 44 +++++++++++++++++++
>>   1 file changed, 44 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
>> new file mode 100644
>> index 000000000000..d96d777d4d9f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
>> @@ -0,0 +1,44 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/fsi/ibm,hub-fsi-controller.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM FSI-attached FSI Hub Controller
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description: |
> Do not need '|' unless you need to preserve formatting.


Ack.


>
>> +  The FSI Hub Controller is an FSI controller, providing a number of FSI links,
>> +  located on a CFAM. Therefore this node will always be a child of an FSI CFAM
>> +  node.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,hub-fsi-controller
> Again, is it for specific chip? SoC? Aren't you using generic
> compatibles (not allowed)?


This one is fairly universally supported on FSI (any POWER chip will 
have it) so I didn't add a specific chip... Should i? Do you mean 
generic compatibles are not allowed? How generic do you mean?


>
>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 09/14] dt-bindings: fsi: Document the FSI Hub Controller

[Eddie James]

On 4/26/24 01:26, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Document the FSI Hub Controller CFAM engine.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../bindings/fsi/ibm,hub-fsi-controller.yaml  | 44 +++++++++++++++++++
>>   1 file changed, 44 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
>> new file mode 100644
>> index 000000000000..d96d777d4d9f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
>> @@ -0,0 +1,44 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/fsi/ibm,hub-fsi-controller.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM FSI-attached FSI Hub Controller
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description: |
> Do not need '|' unless you need to preserve formatting.


Ack.


>
>> +  The FSI Hub Controller is an FSI controller, providing a number of FSI links,
>> +  located on a CFAM. Therefore this node will always be a child of an FSI CFAM
>> +  node.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,hub-fsi-controller
> Again, is it for specific chip? SoC? Aren't you using generic
> compatibles (not allowed)?


This one is fairly universally supported on FSI (any POWER chip will 
have it) so I didn't add a specific chip... Should i? Do you mean 
generic compatibles are not allowed? How generic do you mean?


>
>
>
> Best regards,
> Krzysztof
>

[PATCH v3 09/14] dt-bindings: fsi: Document the FSI Hub Controller

[Krzysztof Kozlowski]

On 26/04/2024 17:19, Eddie James wrote:
>>
>>> +  The FSI Hub Controller is an FSI controller, providing a number of FSI links,
>>> +  located on a CFAM. Therefore this node will always be a child of an FSI CFAM
>>> +  node.
>>> +
>>> +properties:
>>> +  compatible:
>>> +    enum:
>>> +      - ibm,hub-fsi-controller
>> Again, is it for specific chip? SoC? Aren't you using generic
>> compatibles (not allowed)?
> 
> 
> This one is fairly universally supported on FSI (any POWER chip will 
> have it) so I didn't add a specific chip... Should i? Do you mean 
> generic compatibles are not allowed? How generic do you mean?

Maybe IBM is different here, but for every regular SoC the blocks of
that SoC should carry SoC model name/number.

Best regards,
Krzysztof

Re: [PATCH v3 09/14] dt-bindings: fsi: Document the FSI Hub Controller

[Krzysztof Kozlowski]

On 26/04/2024 17:19, Eddie James wrote:
>>
>>> +  The FSI Hub Controller is an FSI controller, providing a number of FSI links,
>>> +  located on a CFAM. Therefore this node will always be a child of an FSI CFAM
>>> +  node.
>>> +
>>> +properties:
>>> +  compatible:
>>> +    enum:
>>> +      - ibm,hub-fsi-controller
>> Again, is it for specific chip? SoC? Aren't you using generic
>> compatibles (not allowed)?
> 
> 
> This one is fairly universally supported on FSI (any POWER chip will 
> have it) so I didn't add a specific chip... Should i? Do you mean 
> generic compatibles are not allowed? How generic do you mean?

Maybe IBM is different here, but for every regular SoC the blocks of
that SoC should carry SoC model name/number.

Best regards,
Krzysztof

[PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format

[Eddie James]

Switch to yaml for the FSI-attached I2C controller.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/i2c/i2c-fsi.txt       | 40 -------------
 .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  | 59 +++++++++++++++++++
 2 files changed, 59 insertions(+), 40 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
 create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml

diff --git a/Documentation/devicetree/bindings/i2c/i2c-fsi.txt b/Documentation/devicetree/bindings/i2c/i2c-fsi.txt
deleted file mode 100644
index b1be2ceb7e69..000000000000
--- a/Documentation/devicetree/bindings/i2c/i2c-fsi.txt
+++ /dev/null
@@ -1,40 +0,0 @@
-Device-tree bindings for FSI-attached I2C master and busses
------------------------------------------------------------
-
-Required properties:
- - compatible = "ibm,i2c-fsi";
- - reg = < address size >;		: The FSI CFAM address and address
-					  space size.
- - #address-cells = <1>;		: Number of address cells in child
-					  nodes.
- - #size-cells = <0>;			: Number of size cells in child nodes.
- - child nodes				: Nodes to describe busses off the I2C
-					  master.
-
-Child node required properties:
- - reg = < port number >		: The port number on the I2C master.
-
-Child node optional properties:
- - child nodes				: Nodes to describe devices on the I2C
-					  bus.
-
-Examples:
-
-    i2c at 1800 {
-        compatible = "ibm,i2c-fsi";
-        reg = < 0x1800 0x400 >;
-        #address-cells = <1>;
-        #size-cells = <0>;
-
-        i2c-bus at 0 {
-            reg = <0>;
-        };
-
-        i2c-bus at 1 {
-            reg = <1>;
-
-            eeprom at 50 {
-                compatible = "vendor,dev-name";
-            };
-        };
-    };
diff --git a/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
new file mode 100644
index 000000000000..473a45de1b6c
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
@@ -0,0 +1,59 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/ibm,i2c-fsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached I2C controller
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  This I2C controller is an FSI CFAM engine, providing access to a number of
+  I2C busses. Therefore this node will always be a child of an FSI CFAM node;
+  see fsi.txt for details on FSI slave and CFAM nodes.
+
+properties:
+  compatible:
+    enum:
+      - ibm,i2c-fsi
+
+  reg:
+    items:
+      - description: FSI slave address
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - $ref: /schemas/i2c/i2c-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    i2c at 1800 {
+        compatible = "ibm,i2c-fsi";
+        reg = <0x1800 0x400>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        i2c-bus at 0 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            reg = <0>;
+        };
+
+        i2c-bus at 1 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            reg = <1>;
+
+            eeprom at 50 {
+                compatible = "atmel,24c64";
+                reg = <0x50>;
+            };
+        };
+    };
-- 
2.39.3

[PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format

[Eddie James]

Switch to yaml for the FSI-attached I2C controller.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../devicetree/bindings/i2c/i2c-fsi.txt       | 40 -------------
 .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  | 59 +++++++++++++++++++
 2 files changed, 59 insertions(+), 40 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
 create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml

diff --git a/Documentation/devicetree/bindings/i2c/i2c-fsi.txt b/Documentation/devicetree/bindings/i2c/i2c-fsi.txt
deleted file mode 100644
index b1be2ceb7e69..000000000000
--- a/Documentation/devicetree/bindings/i2c/i2c-fsi.txt
+++ /dev/null
@@ -1,40 +0,0 @@
-Device-tree bindings for FSI-attached I2C master and busses
------------------------------------------------------------
-
-Required properties:
- - compatible = "ibm,i2c-fsi";
- - reg = < address size >;		: The FSI CFAM address and address
-					  space size.
- - #address-cells = <1>;		: Number of address cells in child
-					  nodes.
- - #size-cells = <0>;			: Number of size cells in child nodes.
- - child nodes				: Nodes to describe busses off the I2C
-					  master.
-
-Child node required properties:
- - reg = < port number >		: The port number on the I2C master.
-
-Child node optional properties:
- - child nodes				: Nodes to describe devices on the I2C
-					  bus.
-
-Examples:
-
-    i2c@1800 {
-        compatible = "ibm,i2c-fsi";
-        reg = < 0x1800 0x400 >;
-        #address-cells = <1>;
-        #size-cells = <0>;
-
-        i2c-bus@0 {
-            reg = <0>;
-        };
-
-        i2c-bus@1 {
-            reg = <1>;
-
-            eeprom@50 {
-                compatible = "vendor,dev-name";
-            };
-        };
-    };
diff --git a/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
new file mode 100644
index 000000000000..473a45de1b6c
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
@@ -0,0 +1,59 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/ibm,i2c-fsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IBM FSI-attached I2C controller
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  This I2C controller is an FSI CFAM engine, providing access to a number of
+  I2C busses. Therefore this node will always be a child of an FSI CFAM node;
+  see fsi.txt for details on FSI slave and CFAM nodes.
+
+properties:
+  compatible:
+    enum:
+      - ibm,i2c-fsi
+
+  reg:
+    items:
+      - description: FSI slave address
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - $ref: /schemas/i2c/i2c-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    i2c@1800 {
+        compatible = "ibm,i2c-fsi";
+        reg = <0x1800 0x400>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        i2c-bus@0 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            reg = <0>;
+        };
+
+        i2c-bus@1 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            reg = <1>;
+
+            eeprom@50 {
+                compatible = "atmel,24c64";
+                reg = <0x50>;
+            };
+        };
+    };
-- 
2.39.3

[PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format

[kernel test robot]

Hi Eddie,

kernel test robot noticed the following build warnings:

[auto build test WARNING on next-20240424]
[also build test WARNING on linus/master v6.9-rc5]
[cannot apply to robh/for-next broonie-spi/for-next andi-shyti/i2c/i2c-host v6.9-rc5 v6.9-rc4 v6.9-rc3]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Eddie-James/dt-bindings-spi-Document-the-IBM-Power-SPI-controller/20240426-054336
base:   next-20240424
patch link:    https://lore.kernel.org/r/20240425213701.655540-11-eajames%40linux.ibm.com
patch subject: [PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format
reproduce: (https://download.01.org/0day-ci/archive/20240426/202404260842.hNo9YEmT-lkp at intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202404260842.hNo9YEmT-lkp at intel.com/

All warnings (new ones prefixed by >>):

   Warning: Documentation/devicetree/bindings/power/wakeup-source.txt references a file that doesn't exist: Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
   Warning: Documentation/devicetree/bindings/regulator/siliconmitus,sm5703-regulator.yaml references a file that doesn't exist: Documentation/devicetree/bindings/mfd/siliconmitus,sm5703.yaml
   Warning: MAINTAINERS references a file that doesn't exist: Documentation/devicetree/bindings/reserved-memory/qcom
   Warning: MAINTAINERS references a file that doesn't exist: Documentation/devicetree/bindings/display/exynos/
>> Warning: MAINTAINERS references a file that doesn't exist: Documentation/devicetree/bindings/i2c/i2c-fsi.txt
   Using alabaster theme

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki

Re: [PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format

[kernel test robot]

Hi Eddie,

kernel test robot noticed the following build warnings:

[auto build test WARNING on next-20240424]
[also build test WARNING on linus/master v6.9-rc5]
[cannot apply to robh/for-next broonie-spi/for-next andi-shyti/i2c/i2c-host v6.9-rc5 v6.9-rc4 v6.9-rc3]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Eddie-James/dt-bindings-spi-Document-the-IBM-Power-SPI-controller/20240426-054336
base:   next-20240424
patch link:    https://lore.kernel.org/r/20240425213701.655540-11-eajames%40linux.ibm.com
patch subject: [PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format
reproduce: (https://download.01.org/0day-ci/archive/20240426/202404260842.hNo9YEmT-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202404260842.hNo9YEmT-lkp@intel.com/

All warnings (new ones prefixed by >>):

   Warning: Documentation/devicetree/bindings/power/wakeup-source.txt references a file that doesn't exist: Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
   Warning: Documentation/devicetree/bindings/regulator/siliconmitus,sm5703-regulator.yaml references a file that doesn't exist: Documentation/devicetree/bindings/mfd/siliconmitus,sm5703.yaml
   Warning: MAINTAINERS references a file that doesn't exist: Documentation/devicetree/bindings/reserved-memory/qcom
   Warning: MAINTAINERS references a file that doesn't exist: Documentation/devicetree/bindings/display/exynos/
>> Warning: MAINTAINERS references a file that doesn't exist: Documentation/devicetree/bindings/i2c/i2c-fsi.txt
   Using alabaster theme

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki

[PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Switch to yaml for the FSI-attached I2C controller.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>

Please use scripts/get_maintainers.pl to get a list of necessary people
and lists to CC (and consider --no-git-fallback argument). It might
happen, that command when run on an older kernel, gives you outdated
entries. Therefore please be sure you base your patches on recent Linux
kernel.

Tools like b4 or scripts/get_maintainer.pl provide you proper list of
people, so fix your workflow. Tools might also fail if you work on some
ancient tree (don't, instead use mainline), work on fork of kernel
(don't, instead use mainline) or you ignore some maintainers (really
don't). Just use b4 and everything should be fine, although remember
about `b4 prep --auto-to-cc` if you added new patches to the patchset.

> ---
>  .../devicetree/bindings/i2c/i2c-fsi.txt       | 40 -------------
>  .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  | 59 +++++++++++++++++++
>  2 files changed, 59 insertions(+), 40 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
>  create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
> 


> -    };
> diff --git a/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
> new file mode 100644
> index 000000000000..473a45de1b6c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
> @@ -0,0 +1,59 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/i2c/ibm,i2c-fsi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM FSI-attached I2C controller
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  This I2C controller is an FSI CFAM engine, providing access to a number of
> +  I2C busses. Therefore this node will always be a child of an FSI CFAM node;
> +  see fsi.txt for details on FSI slave and CFAM nodes.

Here and in all other schemas - remove reference to fsi.txt. You are
going to drop this file once you convert everything, right?

> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,i2c-fsi
> +
> +  reg:
> +    items:
> +      - description: FSI slave address
> +
> +required:
> +  - compatible
> +  - reg
> +
> +allOf:
> +  - $ref: /schemas/i2c/i2c-controller.yaml#
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    i2c at 1800 {

So no wrapper node is needed. Drop the wrapper node in previous patchset
where you introduced one with warning.


Best regards,
Krzysztof

Re: [PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Switch to yaml for the FSI-attached I2C controller.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>

Please use scripts/get_maintainers.pl to get a list of necessary people
and lists to CC (and consider --no-git-fallback argument). It might
happen, that command when run on an older kernel, gives you outdated
entries. Therefore please be sure you base your patches on recent Linux
kernel.

Tools like b4 or scripts/get_maintainer.pl provide you proper list of
people, so fix your workflow. Tools might also fail if you work on some
ancient tree (don't, instead use mainline), work on fork of kernel
(don't, instead use mainline) or you ignore some maintainers (really
don't). Just use b4 and everything should be fine, although remember
about `b4 prep --auto-to-cc` if you added new patches to the patchset.

> ---
>  .../devicetree/bindings/i2c/i2c-fsi.txt       | 40 -------------
>  .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  | 59 +++++++++++++++++++
>  2 files changed, 59 insertions(+), 40 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
>  create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
> 


> -    };
> diff --git a/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
> new file mode 100644
> index 000000000000..473a45de1b6c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
> @@ -0,0 +1,59 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/i2c/ibm,i2c-fsi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: IBM FSI-attached I2C controller
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  This I2C controller is an FSI CFAM engine, providing access to a number of
> +  I2C busses. Therefore this node will always be a child of an FSI CFAM node;
> +  see fsi.txt for details on FSI slave and CFAM nodes.

Here and in all other schemas - remove reference to fsi.txt. You are
going to drop this file once you convert everything, right?

> +
> +properties:
> +  compatible:
> +    enum:
> +      - ibm,i2c-fsi
> +
> +  reg:
> +    items:
> +      - description: FSI slave address
> +
> +required:
> +  - compatible
> +  - reg
> +
> +allOf:
> +  - $ref: /schemas/i2c/i2c-controller.yaml#
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    i2c@1800 {

So no wrapper node is needed. Drop the wrapper node in previous patchset
where you introduced one with warning.


Best regards,
Krzysztof

[PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format

[Eddie James]

On 4/26/24 01:29, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Switch to yaml for the FSI-attached I2C controller.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Please use scripts/get_maintainers.pl to get a list of necessary people
> and lists to CC (and consider --no-git-fallback argument). It might
> happen, that command when run on an older kernel, gives you outdated
> entries. Therefore please be sure you base your patches on recent Linux
> kernel.
>
> Tools like b4 or scripts/get_maintainer.pl provide you proper list of
> people, so fix your workflow. Tools might also fail if you work on some
> ancient tree (don't, instead use mainline), work on fork of kernel
> (don't, instead use mainline) or you ignore some maintainers (really
> don't). Just use b4 and everything should be fine, although remember
> about `b4 prep --auto-to-cc` if you added new patches to the patchset.
>
>> ---
>>   .../devicetree/bindings/i2c/i2c-fsi.txt       | 40 -------------
>>   .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  | 59 +++++++++++++++++++
>>   2 files changed, 59 insertions(+), 40 deletions(-)
>>   delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
>>   create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
>>
>
>> -    };
>> diff --git a/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
>> new file mode 100644
>> index 000000000000..473a45de1b6c
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
>> @@ -0,0 +1,59 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/i2c/ibm,i2c-fsi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM FSI-attached I2C controller
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  This I2C controller is an FSI CFAM engine, providing access to a number of
>> +  I2C busses. Therefore this node will always be a child of an FSI CFAM node;
>> +  see fsi.txt for details on FSI slave and CFAM nodes.
> Here and in all other schemas - remove reference to fsi.txt. You are
> going to drop this file once you convert everything, right?


Good point, yes.


>
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,i2c-fsi
>> +
>> +  reg:
>> +    items:
>> +      - description: FSI slave address
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +
>> +allOf:
>> +  - $ref: /schemas/i2c/i2c-controller.yaml#
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    i2c at 1800 {
> So no wrapper node is needed. Drop the wrapper node in previous patchset
> where you introduced one with warning.


The other one is actually a child node of the equivalent spi controller, 
so it does need some sort of wrapper (address-cells and size-cells don't 
match).


>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 10/14] dt-bindings: i2c: i2c-fsi: Switch to yaml format

[Eddie James]

On 4/26/24 01:29, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Switch to yaml for the FSI-attached I2C controller.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Please use scripts/get_maintainers.pl to get a list of necessary people
> and lists to CC (and consider --no-git-fallback argument). It might
> happen, that command when run on an older kernel, gives you outdated
> entries. Therefore please be sure you base your patches on recent Linux
> kernel.
>
> Tools like b4 or scripts/get_maintainer.pl provide you proper list of
> people, so fix your workflow. Tools might also fail if you work on some
> ancient tree (don't, instead use mainline), work on fork of kernel
> (don't, instead use mainline) or you ignore some maintainers (really
> don't). Just use b4 and everything should be fine, although remember
> about `b4 prep --auto-to-cc` if you added new patches to the patchset.
>
>> ---
>>   .../devicetree/bindings/i2c/i2c-fsi.txt       | 40 -------------
>>   .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  | 59 +++++++++++++++++++
>>   2 files changed, 59 insertions(+), 40 deletions(-)
>>   delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
>>   create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
>>
>
>> -    };
>> diff --git a/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
>> new file mode 100644
>> index 000000000000..473a45de1b6c
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
>> @@ -0,0 +1,59 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/i2c/ibm,i2c-fsi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: IBM FSI-attached I2C controller
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  This I2C controller is an FSI CFAM engine, providing access to a number of
>> +  I2C busses. Therefore this node will always be a child of an FSI CFAM node;
>> +  see fsi.txt for details on FSI slave and CFAM nodes.
> Here and in all other schemas - remove reference to fsi.txt. You are
> going to drop this file once you convert everything, right?


Good point, yes.


>
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ibm,i2c-fsi
>> +
>> +  reg:
>> +    items:
>> +      - description: FSI slave address
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +
>> +allOf:
>> +  - $ref: /schemas/i2c/i2c-controller.yaml#
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    i2c@1800 {
> So no wrapper node is needed. Drop the wrapper node in previous patchset
> where you introduced one with warning.


The other one is actually a child node of the equivalent spi controller, 
so it does need some sort of wrapper (address-cells and size-cells don't 
match).


>
>
> Best regards,
> Krzysztof
>

[PATCH v3 11/14] dt-bindings: arm: aspeed: add IBM P11 BMC boards

[Eddie James]

Document two new AST2600 BMC boards for IBM P11 systems.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index 9a47c4ed4d17..2df91dd1b6a7 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -86,7 +86,9 @@ properties:
               - facebook,harma-bmc
               - facebook,minerva-cmc
               - facebook,yosemite4-bmc
+              - ibm,blueridge-bmc
               - ibm,everest-bmc
+              - ibm,fuji-bmc
               - ibm,rainier-bmc
               - ibm,system1-bmc
               - ibm,tacoma-bmc
-- 
2.39.3

[PATCH v3 11/14] dt-bindings: arm: aspeed: add IBM P11 BMC boards

[Eddie James]

Document two new AST2600 BMC boards for IBM P11 systems.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index 9a47c4ed4d17..2df91dd1b6a7 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -86,7 +86,9 @@ properties:
               - facebook,harma-bmc
               - facebook,minerva-cmc
               - facebook,yosemite4-bmc
+              - ibm,blueridge-bmc
               - ibm,everest-bmc
+              - ibm,fuji-bmc
               - ibm,rainier-bmc
               - ibm,system1-bmc
               - ibm,tacoma-bmc
-- 
2.39.3

[PATCH v3 12/14] ARM: dts: aspeed: Add IBM P11 FSI devices

[Eddie James]

Add the P11 FSI device tree for use in upcoming BMC systems.
Unlike P10, there is no system with only two processors, so
only the quad processor FSI layout is necessary.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++++++++++++
 1 file changed, 1696 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi

diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
new file mode 100644
index 000000000000..c3a0ecf12aa0
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
@@ -0,0 +1,1696 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+
+&fsim0 {
+	status = "okay";
+
+	#address-cells = <2>;
+	#size-cells = <0>;
+
+	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
+
+	cfam at 0,0 {
+		reg = <0 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <0>;
+
+		scom at 1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c at 1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_i2c0: i2c-bus at 0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OMI01 */
+			};
+
+			cfam0_i2c1: i2c-bus at 1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OMI23 */
+			};
+
+			cfam0_i2c10: i2c-bus at a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam0_i2c11: i2c-bus at b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam0_i2c12: i2c-bus at c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+			};
+
+			cfam0_i2c13: i2c-bus at d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+			};
+
+			cfam0_i2c14: i2c-bus at e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam0_i2c15: i2c-bus at f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+		};
+
+		fsi2spi at 1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_spi0: spi at 0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi1: spi at 20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi2: spi at 40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi3: spi at 60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo at 2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ0: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub0: hub at 3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&fsi_hub0 {
+	cfam at 1,0 {
+		reg = <1 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <1>;
+
+		scom at 1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c at 1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_i2c2: i2c-bus at 2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OMI45 */
+			};
+
+			cfam1_i2c3: i2c-bus at 3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OMI67 */
+			};
+
+			cfam1_i2c10: i2c-bus at a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam1_i2c11: i2c-bus at b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam1_i2c14: i2c-bus at e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam1_i2c15: i2c-bus at f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+
+			cfam1_i2c16: i2c-bus at 10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+			};
+
+			cfam1_i2c17: i2c-bus at 11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+			};
+		};
+
+		fsi2spi at 1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_spi0: spi at 0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi1: spi at 20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi2: spi at 40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi3: spi at 60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo at 2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ1: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub1: hub at 3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam at 2,0 {
+		reg = <2 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <2>;
+
+		scom at 1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c at 1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_i2c0: i2c-bus at 0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+			};
+
+			cfam2_i2c1: i2c-bus at 1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+			};
+
+			cfam2_i2c10: i2c-bus at a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam2_i2c11: i2c-bus at b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam2_i2c12: i2c-bus at c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+			};
+
+			cfam2_i2c13: i2c-bus at d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+			};
+
+			cfam2_i2c14: i2c-bus at e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam2_i2c15: i2c-bus at f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+		};
+
+		fsi2spi at 1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_spi0: spi at 0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi1: spi at 20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi2: spi at 40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi3: spi at 60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo at 2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ2: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub2: hub at 3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam at 3,0 {
+		reg = <3 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <3>;
+
+		scom at 1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c at 1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_i2c2: i2c-bus at 2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+			};
+
+			cfam3_i2c3: i2c-bus at 3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+			};
+
+			cfam3_i2c10: i2c-bus at a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam3_i2c11: i2c-bus at b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam3_i2c14: i2c-bus at e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam3_i2c15: i2c-bus at f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+
+			cfam3_i2c16: i2c-bus at 10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+			};
+
+			cfam3_i2c17: i2c-bus at 11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+			};
+		};
+
+		fsi2spi at 1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_spi0: spi at 0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi1: spi at 20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi2: spi at 40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi3: spi at 60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo at 2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ3: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub3: hub at 3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+&cfam0_i2c0 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom100: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo100: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c1 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom101: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo101: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c10 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom110: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo110: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c11 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom111: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo111: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c12 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom112: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo112: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c13 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom113: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo113: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c14 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom114: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo114: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c15 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom115: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo115: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c2 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom202: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo202: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c3 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom203: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo203: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c10 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom210: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo210: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c11 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom211: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo211: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c14 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom214: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo214: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c15 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom215: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo215: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c16 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom216: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo216: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c17 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom217: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo217: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c0 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom300: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo300: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c1 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom301: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo301: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c10 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom310: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo310: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c11 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom311: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo311: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c12 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom312: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo312: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c13 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom313: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo313: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c14 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom314: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo314: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c15 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom315: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo315: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c2 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom402: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo402: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c3 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom403: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo403: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c10 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom410: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo410: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c11 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom411: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo411: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c14 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom414: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo414: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c15 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom415: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo415: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c16 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom416: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo416: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c17 {
+	fsi-i2cr at 20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam at 0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom417: scom at 1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo417: sbefifo at 2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ0 {
+	reg = <1>;
+};
+
+&fsi_occ1 {
+	reg = <2>;
+};
+
+&fsi_occ2 {
+	reg = <3>;
+};
+
+&fsi_occ3 {
+	reg = <4>;
+};
+
+/ {
+	aliases {
+		i2c100 = &cfam0_i2c0;
+		i2c101 = &cfam0_i2c1;
+		i2c110 = &cfam0_i2c10;
+		i2c111 = &cfam0_i2c11;
+		i2c112 = &cfam0_i2c12;
+		i2c113 = &cfam0_i2c13;
+		i2c114 = &cfam0_i2c14;
+		i2c115 = &cfam0_i2c15;
+		i2c202 = &cfam1_i2c2;
+		i2c203 = &cfam1_i2c3;
+		i2c210 = &cfam1_i2c10;
+		i2c211 = &cfam1_i2c11;
+		i2c214 = &cfam1_i2c14;
+		i2c215 = &cfam1_i2c15;
+		i2c216 = &cfam1_i2c16;
+		i2c217 = &cfam1_i2c17;
+		i2c300 = &cfam2_i2c0;
+		i2c301 = &cfam2_i2c1;
+		i2c310 = &cfam2_i2c10;
+		i2c311 = &cfam2_i2c11;
+		i2c312 = &cfam2_i2c12;
+		i2c313 = &cfam2_i2c13;
+		i2c314 = &cfam2_i2c14;
+		i2c315 = &cfam2_i2c15;
+		i2c402 = &cfam3_i2c2;
+		i2c403 = &cfam3_i2c3;
+		i2c410 = &cfam3_i2c10;
+		i2c411 = &cfam3_i2c11;
+		i2c414 = &cfam3_i2c14;
+		i2c415 = &cfam3_i2c15;
+		i2c416 = &cfam3_i2c16;
+		i2c417 = &cfam3_i2c17;
+
+		sbefifo100 = &sbefifo100;
+		sbefifo101 = &sbefifo101;
+		sbefifo110 = &sbefifo110;
+		sbefifo111 = &sbefifo111;
+		sbefifo112 = &sbefifo112;
+		sbefifo113 = &sbefifo113;
+		sbefifo114 = &sbefifo114;
+		sbefifo115 = &sbefifo115;
+		sbefifo202 = &sbefifo202;
+		sbefifo203 = &sbefifo203;
+		sbefifo210 = &sbefifo210;
+		sbefifo211 = &sbefifo211;
+		sbefifo214 = &sbefifo214;
+		sbefifo215 = &sbefifo215;
+		sbefifo216 = &sbefifo216;
+		sbefifo217 = &sbefifo217;
+		sbefifo300 = &sbefifo300;
+		sbefifo301 = &sbefifo301;
+		sbefifo310 = &sbefifo310;
+		sbefifo311 = &sbefifo311;
+		sbefifo312 = &sbefifo312;
+		sbefifo313 = &sbefifo313;
+		sbefifo314 = &sbefifo314;
+		sbefifo315 = &sbefifo315;
+		sbefifo402 = &sbefifo402;
+		sbefifo403 = &sbefifo403;
+		sbefifo410 = &sbefifo410;
+		sbefifo411 = &sbefifo411;
+		sbefifo414 = &sbefifo414;
+		sbefifo415 = &sbefifo415;
+		sbefifo416 = &sbefifo416;
+		sbefifo417 = &sbefifo417;
+
+		scom100 = &scom100;
+		scom101 = &scom101;
+		scom110 = &scom110;
+		scom111 = &scom111;
+		scom112 = &scom112;
+		scom113 = &scom113;
+		scom114 = &scom114;
+		scom115 = &scom115;
+		scom202 = &scom202;
+		scom203 = &scom203;
+		scom210 = &scom210;
+		scom211 = &scom211;
+		scom214 = &scom214;
+		scom215 = &scom215;
+		scom216 = &scom216;
+		scom217 = &scom217;
+		scom300 = &scom300;
+		scom301 = &scom301;
+		scom310 = &scom310;
+		scom311 = &scom311;
+		scom312 = &scom312;
+		scom313 = &scom313;
+		scom314 = &scom314;
+		scom315 = &scom315;
+		scom402 = &scom402;
+		scom403 = &scom403;
+		scom410 = &scom410;
+		scom411 = &scom411;
+		scom414 = &scom414;
+		scom415 = &scom415;
+		scom416 = &scom416;
+		scom417 = &scom417;
+
+		spi10 = &cfam0_spi0;
+		spi11 = &cfam0_spi1;
+		spi12 = &cfam0_spi2;
+		spi13 = &cfam0_spi3;
+		spi20 = &cfam1_spi0;
+		spi21 = &cfam1_spi1;
+		spi22 = &cfam1_spi2;
+		spi23 = &cfam1_spi3;
+		spi30 = &cfam2_spi0;
+		spi31 = &cfam2_spi1;
+		spi32 = &cfam2_spi2;
+		spi33 = &cfam2_spi3;
+		spi40 = &cfam3_spi0;
+		spi41 = &cfam3_spi1;
+		spi42 = &cfam3_spi2;
+		spi43 = &cfam3_spi3;
+	};
+};
-- 
2.39.3

[PATCH v3 12/14] ARM: dts: aspeed: Add IBM P11 FSI devices

[Eddie James]

Add the P11 FSI device tree for use in upcoming BMC systems.
Unlike P10, there is no system with only two processors, so
only the quad processor FSI layout is necessary.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++++++++++++
 1 file changed, 1696 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi

diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
new file mode 100644
index 000000000000..c3a0ecf12aa0
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
@@ -0,0 +1,1696 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+
+&fsim0 {
+	status = "okay";
+
+	#address-cells = <2>;
+	#size-cells = <0>;
+
+	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
+
+	cfam@0,0 {
+		reg = <0 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <0>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OMI01 */
+			};
+
+			cfam0_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OMI23 */
+			};
+
+			cfam0_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam0_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam0_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+			};
+
+			cfam0_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+			};
+
+			cfam0_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam0_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_spi0: spi@0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi1: spi@20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi2: spi@40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi3: spi@60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ0: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub0: hub@3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&fsi_hub0 {
+	cfam@1,0 {
+		reg = <1 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <1>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OMI45 */
+			};
+
+			cfam1_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OMI67 */
+			};
+
+			cfam1_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam1_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam1_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam1_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+
+			cfam1_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+			};
+
+			cfam1_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_spi0: spi@0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi1: spi@20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi2: spi@40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi3: spi@60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ1: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub1: hub@3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@2,0 {
+		reg = <2 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <2>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+			};
+
+			cfam2_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+			};
+
+			cfam2_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam2_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam2_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+			};
+
+			cfam2_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+			};
+
+			cfam2_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam2_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_spi0: spi@0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi1: spi@20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi2: spi@40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi3: spi@60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ2: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub2: hub@3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@3,0 {
+		reg = <3 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <3>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+			};
+
+			cfam3_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+			};
+
+			cfam3_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam3_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam3_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam3_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+
+			cfam3_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+			};
+
+			cfam3_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_spi0: spi@0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi1: spi@20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi2: spi@40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi3: spi@60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ3: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub3: hub@3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+&cfam0_i2c0 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom100: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo100: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c1 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom101: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo101: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c10 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom110: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo110: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c11 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom111: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo111: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c12 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom112: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo112: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c13 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom113: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo113: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c14 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom114: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo114: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c15 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom115: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo115: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c2 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom202: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo202: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c3 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom203: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo203: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c10 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom210: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo210: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c11 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom211: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo211: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c14 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom214: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo214: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c15 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom215: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo215: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c16 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom216: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo216: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c17 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom217: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo217: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c0 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom300: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo300: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c1 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom301: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo301: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c10 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom310: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo310: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c11 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom311: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo311: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c12 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom312: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo312: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c13 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom313: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo313: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c14 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom314: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo314: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam2_i2c15 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom315: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo315: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c2 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom402: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo402: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c3 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom403: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo403: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c10 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom410: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo410: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c11 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom411: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo411: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c14 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom414: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo414: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c15 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom415: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo415: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c16 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom416: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo416: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam3_i2c17 {
+	fsi-i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom417: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo417: sbefifo@2400 {
+				compatible = "ibm,odyssey-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ0 {
+	reg = <1>;
+};
+
+&fsi_occ1 {
+	reg = <2>;
+};
+
+&fsi_occ2 {
+	reg = <3>;
+};
+
+&fsi_occ3 {
+	reg = <4>;
+};
+
+/ {
+	aliases {
+		i2c100 = &cfam0_i2c0;
+		i2c101 = &cfam0_i2c1;
+		i2c110 = &cfam0_i2c10;
+		i2c111 = &cfam0_i2c11;
+		i2c112 = &cfam0_i2c12;
+		i2c113 = &cfam0_i2c13;
+		i2c114 = &cfam0_i2c14;
+		i2c115 = &cfam0_i2c15;
+		i2c202 = &cfam1_i2c2;
+		i2c203 = &cfam1_i2c3;
+		i2c210 = &cfam1_i2c10;
+		i2c211 = &cfam1_i2c11;
+		i2c214 = &cfam1_i2c14;
+		i2c215 = &cfam1_i2c15;
+		i2c216 = &cfam1_i2c16;
+		i2c217 = &cfam1_i2c17;
+		i2c300 = &cfam2_i2c0;
+		i2c301 = &cfam2_i2c1;
+		i2c310 = &cfam2_i2c10;
+		i2c311 = &cfam2_i2c11;
+		i2c312 = &cfam2_i2c12;
+		i2c313 = &cfam2_i2c13;
+		i2c314 = &cfam2_i2c14;
+		i2c315 = &cfam2_i2c15;
+		i2c402 = &cfam3_i2c2;
+		i2c403 = &cfam3_i2c3;
+		i2c410 = &cfam3_i2c10;
+		i2c411 = &cfam3_i2c11;
+		i2c414 = &cfam3_i2c14;
+		i2c415 = &cfam3_i2c15;
+		i2c416 = &cfam3_i2c16;
+		i2c417 = &cfam3_i2c17;
+
+		sbefifo100 = &sbefifo100;
+		sbefifo101 = &sbefifo101;
+		sbefifo110 = &sbefifo110;
+		sbefifo111 = &sbefifo111;
+		sbefifo112 = &sbefifo112;
+		sbefifo113 = &sbefifo113;
+		sbefifo114 = &sbefifo114;
+		sbefifo115 = &sbefifo115;
+		sbefifo202 = &sbefifo202;
+		sbefifo203 = &sbefifo203;
+		sbefifo210 = &sbefifo210;
+		sbefifo211 = &sbefifo211;
+		sbefifo214 = &sbefifo214;
+		sbefifo215 = &sbefifo215;
+		sbefifo216 = &sbefifo216;
+		sbefifo217 = &sbefifo217;
+		sbefifo300 = &sbefifo300;
+		sbefifo301 = &sbefifo301;
+		sbefifo310 = &sbefifo310;
+		sbefifo311 = &sbefifo311;
+		sbefifo312 = &sbefifo312;
+		sbefifo313 = &sbefifo313;
+		sbefifo314 = &sbefifo314;
+		sbefifo315 = &sbefifo315;
+		sbefifo402 = &sbefifo402;
+		sbefifo403 = &sbefifo403;
+		sbefifo410 = &sbefifo410;
+		sbefifo411 = &sbefifo411;
+		sbefifo414 = &sbefifo414;
+		sbefifo415 = &sbefifo415;
+		sbefifo416 = &sbefifo416;
+		sbefifo417 = &sbefifo417;
+
+		scom100 = &scom100;
+		scom101 = &scom101;
+		scom110 = &scom110;
+		scom111 = &scom111;
+		scom112 = &scom112;
+		scom113 = &scom113;
+		scom114 = &scom114;
+		scom115 = &scom115;
+		scom202 = &scom202;
+		scom203 = &scom203;
+		scom210 = &scom210;
+		scom211 = &scom211;
+		scom214 = &scom214;
+		scom215 = &scom215;
+		scom216 = &scom216;
+		scom217 = &scom217;
+		scom300 = &scom300;
+		scom301 = &scom301;
+		scom310 = &scom310;
+		scom311 = &scom311;
+		scom312 = &scom312;
+		scom313 = &scom313;
+		scom314 = &scom314;
+		scom315 = &scom315;
+		scom402 = &scom402;
+		scom403 = &scom403;
+		scom410 = &scom410;
+		scom411 = &scom411;
+		scom414 = &scom414;
+		scom415 = &scom415;
+		scom416 = &scom416;
+		scom417 = &scom417;
+
+		spi10 = &cfam0_spi0;
+		spi11 = &cfam0_spi1;
+		spi12 = &cfam0_spi2;
+		spi13 = &cfam0_spi3;
+		spi20 = &cfam1_spi0;
+		spi21 = &cfam1_spi1;
+		spi22 = &cfam1_spi2;
+		spi23 = &cfam1_spi3;
+		spi30 = &cfam2_spi0;
+		spi31 = &cfam2_spi1;
+		spi32 = &cfam2_spi2;
+		spi33 = &cfam2_spi3;
+		spi40 = &cfam3_spi0;
+		spi41 = &cfam3_spi1;
+		spi42 = &cfam3_spi2;
+		spi43 = &cfam3_spi3;
+	};
+};
-- 
2.39.3

[PATCH v3 12/14] ARM: dts: aspeed: Add IBM P11 FSI devices

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Add the P11 FSI device tree for use in upcoming BMC systems.
> Unlike P10, there is no system with only two processors, so
> only the quad processor FSI layout is necessary.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++++++++++++
>  1 file changed, 1696 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
> 
> diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
> new file mode 100644
> index 000000000000..c3a0ecf12aa0
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
> @@ -0,0 +1,1696 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2024 IBM Corp.
> +
> +&fsim0 {

This does not make sense. You do not include any file here, so what do
you want to override?

How can you even test this file?

> +	status = "okay";
> +
> +	#address-cells = <2>;
> +	#size-cells = <0>;
> +
> +	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
> +


> +
> +&cfam3_i2c16 {
> +	fsi-i2cr at 20 {
> +		compatible = "ibm,i2cr-fsi-master";
> +		reg = <0x20>;
> +		#address-cells = <2>;
> +		#size-cells = <0>;
> +
> +		cfam at 0,0 {
> +			reg = <0 0>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			chip-id = <0>;
> +
> +			scom416: scom at 1000 {
> +				compatible = "ibm,i2cr-scom";
> +				reg = <0x1000 0x400>;
> +			};
> +
> +			sbefifo416: sbefifo at 2400 {
> +				compatible = "ibm,odyssey-sbefifo";
> +				reg = <0x2400 0x400>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +		};
> +	};
> +};
> +
> +&cfam3_i2c17 {

This looks randomly ordered.


> +&fsi_occ1 {
> +	reg = <2>;
> +};
> +
> +&fsi_occ2 {
> +	reg = <3>;
> +};
> +
> +&fsi_occ3 {
> +	reg = <4>;
> +};
> +
> +/ {

Nope. Root node never goes to end of file. Look at all modern DTS.

> +	aliases {
> +		i2c100 = &cfam0_i2c0;
> +		i2c101 = &cfam0_i2c1;
> +		i2c110 = &cfam0_i2c10;
> +		i2c111 = &cfam0_i2c11;
> +		i2c112 = &cfam0_i2c12;
> +		i2c113 = &cfam0_i2c13;
> +		i2c114 = &cfam0_i2c14;
> +		i2c115 = &cfam0_i2c15;
> +		i2c202 = &cfam1_i2c2;
> +		i2c203 = &cfam1_i2c3;
> +		i2c210 = &cfam1_i2c10;



Best regards,
Krzysztof

Re: [PATCH v3 12/14] ARM: dts: aspeed: Add IBM P11 FSI devices

[Krzysztof Kozlowski]

On 25/04/2024 23:36, Eddie James wrote:
> Add the P11 FSI device tree for use in upcoming BMC systems.
> Unlike P10, there is no system with only two processors, so
> only the quad processor FSI layout is necessary.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++++++++++++
>  1 file changed, 1696 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
> 
> diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
> new file mode 100644
> index 000000000000..c3a0ecf12aa0
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
> @@ -0,0 +1,1696 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2024 IBM Corp.
> +
> +&fsim0 {

This does not make sense. You do not include any file here, so what do
you want to override?

How can you even test this file?

> +	status = "okay";
> +
> +	#address-cells = <2>;
> +	#size-cells = <0>;
> +
> +	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
> +


> +
> +&cfam3_i2c16 {
> +	fsi-i2cr@20 {
> +		compatible = "ibm,i2cr-fsi-master";
> +		reg = <0x20>;
> +		#address-cells = <2>;
> +		#size-cells = <0>;
> +
> +		cfam@0,0 {
> +			reg = <0 0>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			chip-id = <0>;
> +
> +			scom416: scom@1000 {
> +				compatible = "ibm,i2cr-scom";
> +				reg = <0x1000 0x400>;
> +			};
> +
> +			sbefifo416: sbefifo@2400 {
> +				compatible = "ibm,odyssey-sbefifo";
> +				reg = <0x2400 0x400>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +		};
> +	};
> +};
> +
> +&cfam3_i2c17 {

This looks randomly ordered.


> +&fsi_occ1 {
> +	reg = <2>;
> +};
> +
> +&fsi_occ2 {
> +	reg = <3>;
> +};
> +
> +&fsi_occ3 {
> +	reg = <4>;
> +};
> +
> +/ {

Nope. Root node never goes to end of file. Look at all modern DTS.

> +	aliases {
> +		i2c100 = &cfam0_i2c0;
> +		i2c101 = &cfam0_i2c1;
> +		i2c110 = &cfam0_i2c10;
> +		i2c111 = &cfam0_i2c11;
> +		i2c112 = &cfam0_i2c12;
> +		i2c113 = &cfam0_i2c13;
> +		i2c114 = &cfam0_i2c14;
> +		i2c115 = &cfam0_i2c15;
> +		i2c202 = &cfam1_i2c2;
> +		i2c203 = &cfam1_i2c3;
> +		i2c210 = &cfam1_i2c10;



Best regards,
Krzysztof

[PATCH v3 12/14] ARM: dts: aspeed: Add IBM P11 FSI devices

[Eddie James]

On 4/26/24 01:31, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Add the P11 FSI device tree for use in upcoming BMC systems.
>> Unlike P10, there is no system with only two processors, so
>> only the quad processor FSI layout is necessary.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++++++++++++
>>   1 file changed, 1696 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>>
>> diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>> new file mode 100644
>> index 000000000000..c3a0ecf12aa0
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>> @@ -0,0 +1,1696 @@
>> +// SPDX-License-Identifier: GPL-2.0-or-later
>> +// Copyright 2024 IBM Corp.
>> +
>> +&fsim0 {
> This does not make sense. You do not include any file here, so what do
> you want to override?
>
> How can you even test this file?


This is an include file, to be included in the new device tree files in 
the next two patches. It will be tested as part of those. Andrew 
requested I split this up, and I have to add this one first, even though 
nothing is referencing it yet. The same model is used for the P10 FSI 
devices.


>
>> +	status = "okay";
>> +
>> +	#address-cells = <2>;
>> +	#size-cells = <0>;
>> +
>> +	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
>> +
>
>> +
>> +&cfam3_i2c16 {
>> +	fsi-i2cr at 20 {
>> +		compatible = "ibm,i2cr-fsi-master";
>> +		reg = <0x20>;
>> +		#address-cells = <2>;
>> +		#size-cells = <0>;
>> +
>> +		cfam at 0,0 {
>> +			reg = <0 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			chip-id = <0>;
>> +
>> +			scom416: scom at 1000 {
>> +				compatible = "ibm,i2cr-scom";
>> +				reg = <0x1000 0x400>;
>> +			};
>> +
>> +			sbefifo416: sbefifo at 2400 {
>> +				compatible = "ibm,odyssey-sbefifo";
>> +				reg = <0x2400 0x400>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&cfam3_i2c17 {
> This looks randomly ordered.


Not sure what you mean. Everything is sequentially ordered?


>
>
>> +&fsi_occ1 {
>> +	reg = <2>;
>> +};
>> +
>> +&fsi_occ2 {
>> +	reg = <3>;
>> +};
>> +
>> +&fsi_occ3 {
>> +	reg = <4>;
>> +};
>> +
>> +/ {
> Nope. Root node never goes to end of file. Look at all modern DTS.


Ack.


>
>> +	aliases {
>> +		i2c100 = &cfam0_i2c0;
>> +		i2c101 = &cfam0_i2c1;
>> +		i2c110 = &cfam0_i2c10;
>> +		i2c111 = &cfam0_i2c11;
>> +		i2c112 = &cfam0_i2c12;
>> +		i2c113 = &cfam0_i2c13;
>> +		i2c114 = &cfam0_i2c14;
>> +		i2c115 = &cfam0_i2c15;
>> +		i2c202 = &cfam1_i2c2;
>> +		i2c203 = &cfam1_i2c3;
>> +		i2c210 = &cfam1_i2c10;
>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 12/14] ARM: dts: aspeed: Add IBM P11 FSI devices

[Eddie James]

On 4/26/24 01:31, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:36, Eddie James wrote:
>> Add the P11 FSI device tree for use in upcoming BMC systems.
>> Unlike P10, there is no system with only two processors, so
>> only the quad processor FSI layout is necessary.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++++++++++++
>>   1 file changed, 1696 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>>
>> diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>> new file mode 100644
>> index 000000000000..c3a0ecf12aa0
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>> @@ -0,0 +1,1696 @@
>> +// SPDX-License-Identifier: GPL-2.0-or-later
>> +// Copyright 2024 IBM Corp.
>> +
>> +&fsim0 {
> This does not make sense. You do not include any file here, so what do
> you want to override?
>
> How can you even test this file?


This is an include file, to be included in the new device tree files in 
the next two patches. It will be tested as part of those. Andrew 
requested I split this up, and I have to add this one first, even though 
nothing is referencing it yet. The same model is used for the P10 FSI 
devices.


>
>> +	status = "okay";
>> +
>> +	#address-cells = <2>;
>> +	#size-cells = <0>;
>> +
>> +	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
>> +
>
>> +
>> +&cfam3_i2c16 {
>> +	fsi-i2cr@20 {
>> +		compatible = "ibm,i2cr-fsi-master";
>> +		reg = <0x20>;
>> +		#address-cells = <2>;
>> +		#size-cells = <0>;
>> +
>> +		cfam@0,0 {
>> +			reg = <0 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			chip-id = <0>;
>> +
>> +			scom416: scom@1000 {
>> +				compatible = "ibm,i2cr-scom";
>> +				reg = <0x1000 0x400>;
>> +			};
>> +
>> +			sbefifo416: sbefifo@2400 {
>> +				compatible = "ibm,odyssey-sbefifo";
>> +				reg = <0x2400 0x400>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&cfam3_i2c17 {
> This looks randomly ordered.


Not sure what you mean. Everything is sequentially ordered?


>
>
>> +&fsi_occ1 {
>> +	reg = <2>;
>> +};
>> +
>> +&fsi_occ2 {
>> +	reg = <3>;
>> +};
>> +
>> +&fsi_occ3 {
>> +	reg = <4>;
>> +};
>> +
>> +/ {
> Nope. Root node never goes to end of file. Look at all modern DTS.


Ack.


>
>> +	aliases {
>> +		i2c100 = &cfam0_i2c0;
>> +		i2c101 = &cfam0_i2c1;
>> +		i2c110 = &cfam0_i2c10;
>> +		i2c111 = &cfam0_i2c11;
>> +		i2c112 = &cfam0_i2c12;
>> +		i2c113 = &cfam0_i2c13;
>> +		i2c114 = &cfam0_i2c14;
>> +		i2c115 = &cfam0_i2c15;
>> +		i2c202 = &cfam1_i2c2;
>> +		i2c203 = &cfam1_i2c3;
>> +		i2c210 = &cfam1_i2c10;
>
>
> Best regards,
> Krzysztof
>

[PATCH v3 12/14] ARM: dts: aspeed: Add IBM P11 FSI devices

[Krzysztof Kozlowski]

On 26/04/2024 15:18, Eddie James wrote:
> 
> On 4/26/24 01:31, Krzysztof Kozlowski wrote:
>> On 25/04/2024 23:36, Eddie James wrote:
>>> Add the P11 FSI device tree for use in upcoming BMC systems.
>>> Unlike P10, there is no system with only two processors, so
>>> only the quad processor FSI layout is necessary.
>>>
>>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>>> ---
>>>   .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++++++++++++
>>>   1 file changed, 1696 insertions(+)
>>>   create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>>>
>>> diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>>> new file mode 100644
>>> index 000000000000..c3a0ecf12aa0
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>>> @@ -0,0 +1,1696 @@
>>> +// SPDX-License-Identifier: GPL-2.0-or-later
>>> +// Copyright 2024 IBM Corp.
>>> +
>>> +&fsim0 {
>> This does not make sense. You do not include any file here, so what do
>> you want to override?
>>
>> How can you even test this file?
> 
> 
> This is an include file, to be included in the new device tree files in 
> the next two patches. It will be tested as part of those. Andrew 
> requested I split this up, and I have to add this one first, even though 
> nothing is referencing it yet. The same model is used for the P10 FSI 
> devices.
> 
> 
>>
>>> +	status = "okay";
>>> +
>>> +	#address-cells = <2>;
>>> +	#size-cells = <0>;
>>> +
>>> +	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
>>> +
>>
>>> +
>>> +&cfam3_i2c16 {
>>> +	fsi-i2cr at 20 {
>>> +		compatible = "ibm,i2cr-fsi-master";
>>> +		reg = <0x20>;
>>> +		#address-cells = <2>;
>>> +		#size-cells = <0>;
>>> +
>>> +		cfam at 0,0 {
>>> +			reg = <0 0>;
>>> +			#address-cells = <1>;
>>> +			#size-cells = <1>;
>>> +			chip-id = <0>;
>>> +
>>> +			scom416: scom at 1000 {
>>> +				compatible = "ibm,i2cr-scom";
>>> +				reg = <0x1000 0x400>;
>>> +			};
>>> +
>>> +			sbefifo416: sbefifo at 2400 {
>>> +				compatible = "ibm,odyssey-sbefifo";
>>> +				reg = <0x2400 0x400>;
>>> +				#address-cells = <1>;
>>> +				#size-cells = <0>;
>>> +			};
>>> +		};
>>> +	};
>>> +};
>>> +
>>> +&cfam3_i2c17 {
>> This looks randomly ordered.
> 
> 
> Not sure what you mean. Everything is sequentially ordered?

So what is the order for all Aspeed DTS? Is it sequential like in DTSI?
What does it even mean sequential?  There are two preferred orderings,
as expressed in DTS coding style.

Best regards,
Krzysztof

Re: [PATCH v3 12/14] ARM: dts: aspeed: Add IBM P11 FSI devices

[Krzysztof Kozlowski]

On 26/04/2024 15:18, Eddie James wrote:
> 
> On 4/26/24 01:31, Krzysztof Kozlowski wrote:
>> On 25/04/2024 23:36, Eddie James wrote:
>>> Add the P11 FSI device tree for use in upcoming BMC systems.
>>> Unlike P10, there is no system with only two processors, so
>>> only the quad processor FSI layout is necessary.
>>>
>>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>>> ---
>>>   .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++++++++++++
>>>   1 file changed, 1696 insertions(+)
>>>   create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>>>
>>> diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>>> new file mode 100644
>>> index 000000000000..c3a0ecf12aa0
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
>>> @@ -0,0 +1,1696 @@
>>> +// SPDX-License-Identifier: GPL-2.0-or-later
>>> +// Copyright 2024 IBM Corp.
>>> +
>>> +&fsim0 {
>> This does not make sense. You do not include any file here, so what do
>> you want to override?
>>
>> How can you even test this file?
> 
> 
> This is an include file, to be included in the new device tree files in 
> the next two patches. It will be tested as part of those. Andrew 
> requested I split this up, and I have to add this one first, even though 
> nothing is referencing it yet. The same model is used for the P10 FSI 
> devices.
> 
> 
>>
>>> +	status = "okay";
>>> +
>>> +	#address-cells = <2>;
>>> +	#size-cells = <0>;
>>> +
>>> +	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
>>> +
>>
>>> +
>>> +&cfam3_i2c16 {
>>> +	fsi-i2cr@20 {
>>> +		compatible = "ibm,i2cr-fsi-master";
>>> +		reg = <0x20>;
>>> +		#address-cells = <2>;
>>> +		#size-cells = <0>;
>>> +
>>> +		cfam@0,0 {
>>> +			reg = <0 0>;
>>> +			#address-cells = <1>;
>>> +			#size-cells = <1>;
>>> +			chip-id = <0>;
>>> +
>>> +			scom416: scom@1000 {
>>> +				compatible = "ibm,i2cr-scom";
>>> +				reg = <0x1000 0x400>;
>>> +			};
>>> +
>>> +			sbefifo416: sbefifo@2400 {
>>> +				compatible = "ibm,odyssey-sbefifo";
>>> +				reg = <0x2400 0x400>;
>>> +				#address-cells = <1>;
>>> +				#size-cells = <0>;
>>> +			};
>>> +		};
>>> +	};
>>> +};
>>> +
>>> +&cfam3_i2c17 {
>> This looks randomly ordered.
> 
> 
> Not sure what you mean. Everything is sequentially ordered?

So what is the order for all Aspeed DTS? Is it sequential like in DTSI?
What does it even mean sequential?  There are two preferred orderings,
as expressed in DTS coding style.

Best regards,
Krzysztof

[PATCH v3 13/14] ARM: dts: aspeed: Add IBM P11 Blueridge BMC system

[Eddie James]

Add the device tree for the new BMC system. The Blueridge is a
P11 system with four processors.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++++++++++++
 1 file changed, 1711 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
new file mode 100644
index 000000000000..8503ce2480b5
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
@@ -0,0 +1,1711 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Blueridge";
+	compatible = "ibm,blueridge-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		i2c16 = &i2c2mux0;
+		i2c17 = &i2c2mux1;
+		i2c18 = &i2c2mux2;
+		i2c19 = &i2c2mux3;
+		i2c20 = &i2c4mux0chn0;
+		i2c21 = &i2c4mux0chn1;
+		i2c22 = &i2c4mux0chn2;
+		i2c23 = &i2c5mux0chn0;
+		i2c24 = &i2c5mux0chn1;
+		i2c25 = &i2c6mux0chn0;
+		i2c26 = &i2c6mux0chn1;
+		i2c27 = &i2c6mux0chn2;
+		i2c28 = &i2c6mux0chn3;
+		i2c29 = &i2c11mux0chn0;
+		i2c30 = &i2c11mux0chn1;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8 earlycon";
+	};
+
+	memory at 80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: tcg_event_log at b3d00000 {
+			no-map;
+			reg = <0xb3d00000 0x100000>;
+		};
+
+		ramoops at b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region at b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region at bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	i2c2mux: i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		i2c-parent = <&i2c2>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>,
+			    <&gpio0 ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
+		idle-state = <0>;
+
+		i2c2mux0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c2mux1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c2mux2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c2mux3: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* BMC Card fault LED at the back */
+		led-bmc-ingraham0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure ID LED at the back */
+		led-rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure fault LED at the back */
+		led-rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		/* PCIE slot power LED */
+		led-pcieslot-power {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-fan0-presence {
+			label = "fan0-presence";
+			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
+			linux,code = <6>;
+		};
+
+		event-fan1-presence {
+			label = "fan1-presence";
+			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
+			linux,code = <7>;
+		};
+
+		event-fan2-presence {
+			label = "fan2-presence";
+			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
+			linux,code = <8>;
+		};
+
+		event-fan3-presence {
+			label = "fan3-presence";
+			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
+			linux,code = <9>;
+		};
+
+		event-fan4-presence {
+			label = "fan4-presence";
+			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
+			linux,code = <10>;
+		};
+
+		event-fan5-presence {
+			label = "fan5-presence";
+			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
+			linux,code = <11>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","","","","checkstop","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
+	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","usb-power","","","","",
+	/*P0-P7*/	"","","","","pcieslot-power","","","",
+	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
+	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
+	"power-ffs-sync-history","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+
+	i2c3_mux_oe_n-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
+		output-high;
+		line-name = "I2C3_MUX_OE_N";
+	};
+
+	usb_power-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <180>, <180>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom at 51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	tca_pres1: tca9554 at 20{
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "",
+			"RUSSEL_FW_I2C_ENABLE_N",
+			"RUSSEL_OPPANEL_PRESENCE_N",
+			"BLYTH_OPPANEL_PRESENCE_N",
+			"CPU_TPM_CARD_PRESENT_N",
+			"DASD_BP2_PRESENT_N",
+			"DASD_BP1_PRESENT_N",
+			"DASD_BP0_PRESENT_N";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	power-supply at 68 {
+		compatible = "ibm,cffps";
+		reg = <0x68>;
+	};
+
+	power-supply at 69 {
+		compatible = "ibm,cffps";
+		reg = <0x69>;
+	};
+
+	pca_pres1: pca9552 at 61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD",
+			"SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD",
+			"SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N",
+			"SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N",
+			"SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N",
+			"", "", "", "", "", "";
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	tmp275 at 48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275 at 49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	tmp275 at 4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca9551 at 60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard0-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard0-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom at 51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+
+		i2c4mux0chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom at 52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	tmp275 at 48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275 at 49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca9551 at 60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard3-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard3-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom at 51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca9551 at 61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard4-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard4-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	tmp275 at 48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275 at 4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	tmp275 at 4b {
+		compatible = "ti,tmp275";
+		reg = <0x4b>;
+	};
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c6mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c6mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom at 52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+
+		i2c6mux0chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		i2c6mux0chn3: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom at 51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+&i2c7 {
+	multi-master;
+	status = "okay";
+
+	pca9552 at 30 {
+		compatible = "ibm,pca9552";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "pcieslot0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "pcieslot1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "pcieslot2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "pcieslot3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "pcieslot4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "cpu1";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "cpu-vrm1";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "lcd-russel";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca9552 at 31 {
+		compatible = "ibm,pca9552";
+		reg = <0x31>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "ddimm0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "ddimm1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "ddimm2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "ddimm3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "ddimm4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "ddimm5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "ddimm6";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "ddimm7";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "ddimm8";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "ddimm9";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "ddimm10";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "ddimm11";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 12 {
+			label = "ddimm12";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 13 {
+			label = "ddimm13";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 14 {
+			label = "ddimm14";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 15 {
+			label = "ddimm15";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca9552 at 32 {
+		compatible = "ibm,pca9552";
+		reg = <0x32>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "ddimm16";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "ddimm17";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "ddimm18";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "ddimm19";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "ddimm20";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "ddimm21";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "ddimm22";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "ddimm23";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "ddimm24";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "ddimm25";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "ddimm26";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "ddimm27";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 12 {
+			label = "ddimm28";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 13 {
+			label = "ddimm29";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 14 {
+			label = "ddimm30";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 15 {
+			label = "ddimm31";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca9552 at 33 {
+		compatible = "ibm,pca9552";
+		reg = <0x33>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "planar";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "cpu0";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "dasd-pyramid0";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "dasd-pyramid1";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "dasd-pyramid2";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "cpu0-vrm0";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "rtc-battery";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "base-blyth";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "pcieslot6";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "pcieslot7";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "pcieslot8";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 12 {
+			label = "pcieslot9";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 13 {
+			label = "pcieslot10";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 14 {
+			label = "pcieslot11";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 15 {
+			label = "tpm-wilson";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	si7021-a20 at 40 {
+		compatible = "silabs,si7020";
+		reg = <0x40>;
+	};
+
+	tmp275 at 48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	max: max31785 at 52 {
+		compatible = "maxim,max31785a";
+		reg = <0x52>;
+	};
+
+	pca9551 at 60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "front-sys-id0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "front-check-log0";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "front-enc-fault1";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "front-sys-pwron0";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca0: pca9552 at 61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "fan0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "fan1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "fan2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "fan3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "fan4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "fan5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	ibm-panel at 62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	dps: dps310 at 76 {
+		compatible = "infineon,dps310";
+		reg = <0x76>;
+		#io-channel-cells = <0>;
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom at 51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	ucd90320 at 11 {
+		compatible = "ti,ucd90320";
+		reg = <0x11>;
+	};
+
+	rtc at 32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	tmp275 at 48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275 at 4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom at 51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	pca_pres3: pca9552 at 60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"", "", "", "", "", "", "", "",
+			"", "", "", "", "", "", "power-config-full-load", "";
+	};
+
+	pca_pres2: pca9552 at 61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SLOT6_PRSNT_EN_RSVD", "SLOT7_PRSNT_EN_RSVD",
+			"SLOT8_PRSNT_EN_RSVD", "SLOT9_PRSNT_EN_RSVD",
+			"SLOT10_PRSNT_EN_RSVD", "SLOT11_PRSNT_EN_RSVD",
+			"SLOT6_EXPANDER_PRSNT_N", "SLOT7_EXPANDER_PRSNT_N",
+			"SLOT8_EXPANDER_PRSNT_N", "SLOT9_EXPANDER_PRSNT_N",
+			"SLOT10_EXPANDER_PRSNT_N", "SLOT11_EXPANDER_PRSNT_N",
+			"", "", "", "";
+	};
+
+};
+
+&i2c9 {
+	status = "okay";
+
+	tmp423a at 4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	tmp423b at 4d {
+		compatible = "ti,tmp423";
+		reg = <0x4d>;
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	tmp423a at 4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	tmp423b at 4d {
+		compatible = "ti,tmp423";
+		reg = <0x4d>;
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	tmp275 at 48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275 at 49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c11mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca9551 at 60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard10-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard10-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c11mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom at 51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm at 2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom at 50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9552 at 60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "nvme0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "nvme1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "nvme2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "nvme3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "nvme4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "nvme5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "nvme6";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "nvme7";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+
+	eeprom at 50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9552 at 60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "nvme8";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "nvme9";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "nvme10";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "nvme11";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "nvme12";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "nvme13";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "nvme14";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "nvme15";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	eeprom at 50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9552 at 60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "nvme16";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "nvme17";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "nvme18";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "nvme19";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "nvme20";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "nvme21";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "nvme22";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "nvme23";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&xdma {
+	status = "okay";
+	memory-region = <&vga_memory>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+#include "ibm-power11-quad.dtsi"
-- 
2.39.3

[PATCH v3 13/14] ARM: dts: aspeed: Add IBM P11 Blueridge BMC system

[Eddie James]

Add the device tree for the new BMC system. The Blueridge is a
P11 system with four processors.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++++++++++++
 1 file changed, 1711 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
new file mode 100644
index 000000000000..8503ce2480b5
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
@@ -0,0 +1,1711 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Blueridge";
+	compatible = "ibm,blueridge-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		i2c16 = &i2c2mux0;
+		i2c17 = &i2c2mux1;
+		i2c18 = &i2c2mux2;
+		i2c19 = &i2c2mux3;
+		i2c20 = &i2c4mux0chn0;
+		i2c21 = &i2c4mux0chn1;
+		i2c22 = &i2c4mux0chn2;
+		i2c23 = &i2c5mux0chn0;
+		i2c24 = &i2c5mux0chn1;
+		i2c25 = &i2c6mux0chn0;
+		i2c26 = &i2c6mux0chn1;
+		i2c27 = &i2c6mux0chn2;
+		i2c28 = &i2c6mux0chn3;
+		i2c29 = &i2c11mux0chn0;
+		i2c30 = &i2c11mux0chn1;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: tcg_event_log@b3d00000 {
+			no-map;
+			reg = <0xb3d00000 0x100000>;
+		};
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	i2c2mux: i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		i2c-parent = <&i2c2>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>,
+			    <&gpio0 ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
+		idle-state = <0>;
+
+		i2c2mux0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c2mux1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c2mux2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c2mux3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* BMC Card fault LED at the back */
+		led-bmc-ingraham0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure ID LED at the back */
+		led-rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure fault LED at the back */
+		led-rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		/* PCIE slot power LED */
+		led-pcieslot-power {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-fan0-presence {
+			label = "fan0-presence";
+			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
+			linux,code = <6>;
+		};
+
+		event-fan1-presence {
+			label = "fan1-presence";
+			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
+			linux,code = <7>;
+		};
+
+		event-fan2-presence {
+			label = "fan2-presence";
+			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
+			linux,code = <8>;
+		};
+
+		event-fan3-presence {
+			label = "fan3-presence";
+			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
+			linux,code = <9>;
+		};
+
+		event-fan4-presence {
+			label = "fan4-presence";
+			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
+			linux,code = <10>;
+		};
+
+		event-fan5-presence {
+			label = "fan5-presence";
+			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
+			linux,code = <11>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","","","","checkstop","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
+	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","usb-power","","","","",
+	/*P0-P7*/	"","","","","pcieslot-power","","","",
+	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
+	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
+	"power-ffs-sync-history","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+
+	i2c3_mux_oe_n-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
+		output-high;
+		line-name = "I2C3_MUX_OE_N";
+	};
+
+	usb_power-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <180>, <180>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	tca_pres1: tca9554@20{
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "",
+			"RUSSEL_FW_I2C_ENABLE_N",
+			"RUSSEL_OPPANEL_PRESENCE_N",
+			"BLYTH_OPPANEL_PRESENCE_N",
+			"CPU_TPM_CARD_PRESENT_N",
+			"DASD_BP2_PRESENT_N",
+			"DASD_BP1_PRESENT_N",
+			"DASD_BP0_PRESENT_N";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	power-supply@68 {
+		compatible = "ibm,cffps";
+		reg = <0x68>;
+	};
+
+	power-supply@69 {
+		compatible = "ibm,cffps";
+		reg = <0x69>;
+	};
+
+	pca_pres1: pca9552@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD",
+			"SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD",
+			"SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N",
+			"SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N",
+			"SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N",
+			"", "", "", "", "", "";
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	tmp275@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard0-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard0-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+
+		i2c4mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard3-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard3-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca9551@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard4-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard4-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	tmp275@4b {
+		compatible = "ti,tmp275";
+		reg = <0x4b>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c6mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c6mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+
+		i2c6mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		i2c6mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+&i2c7 {
+	multi-master;
+	status = "okay";
+
+	pca9552@30 {
+		compatible = "ibm,pca9552";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "pcieslot0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "pcieslot1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "pcieslot2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "pcieslot3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "pcieslot4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "cpu1";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "cpu-vrm1";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "lcd-russel";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca9552@31 {
+		compatible = "ibm,pca9552";
+		reg = <0x31>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm6";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm7";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm8";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm9";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm10";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm11";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm12";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm13";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm14";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm15";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca9552@32 {
+		compatible = "ibm,pca9552";
+		reg = <0x32>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm16";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm17";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm18";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm19";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm20";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm21";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm22";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm23";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm24";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm25";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm26";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm27";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm28";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm29";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm30";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm31";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca9552@33 {
+		compatible = "ibm,pca9552";
+		reg = <0x33>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "planar";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "cpu0";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "dasd-pyramid0";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "dasd-pyramid1";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "dasd-pyramid2";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "cpu0-vrm0";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "rtc-battery";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "base-blyth";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "pcieslot6";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "pcieslot7";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "pcieslot8";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "pcieslot9";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "pcieslot10";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "pcieslot11";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "tpm-wilson";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	si7021-a20@40 {
+		compatible = "silabs,si7020";
+		reg = <0x40>;
+	};
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	max: max31785@52 {
+		compatible = "maxim,max31785a";
+		reg = <0x52>;
+	};
+
+	pca9551@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "front-sys-id0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "front-check-log0";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "front-enc-fault1";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "front-sys-pwron0";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca0: pca9552@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "fan0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "fan1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "fan2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "fan3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "fan4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "fan5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	ibm-panel@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	dps: dps310@76 {
+		compatible = "infineon,dps310";
+		reg = <0x76>;
+		#io-channel-cells = <0>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	ucd90320@11 {
+		compatible = "ti,ucd90320";
+		reg = <0x11>;
+	};
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	pca_pres3: pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"", "", "", "", "", "", "", "",
+			"", "", "", "", "", "", "power-config-full-load", "";
+	};
+
+	pca_pres2: pca9552@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SLOT6_PRSNT_EN_RSVD", "SLOT7_PRSNT_EN_RSVD",
+			"SLOT8_PRSNT_EN_RSVD", "SLOT9_PRSNT_EN_RSVD",
+			"SLOT10_PRSNT_EN_RSVD", "SLOT11_PRSNT_EN_RSVD",
+			"SLOT6_EXPANDER_PRSNT_N", "SLOT7_EXPANDER_PRSNT_N",
+			"SLOT8_EXPANDER_PRSNT_N", "SLOT9_EXPANDER_PRSNT_N",
+			"SLOT10_EXPANDER_PRSNT_N", "SLOT11_EXPANDER_PRSNT_N",
+			"", "", "", "";
+	};
+
+};
+
+&i2c9 {
+	status = "okay";
+
+	tmp423a@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	tmp423b@4d {
+		compatible = "ti,tmp423";
+		reg = <0x4d>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	tmp423a@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	tmp423b@4d {
+		compatible = "ti,tmp423";
+		reg = <0x4d>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c11mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard10-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard10-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c11mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm@2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nvme0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "nvme1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "nvme2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nvme3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "nvme4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "nvme5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "nvme6";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "nvme7";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nvme8";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "nvme9";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "nvme10";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nvme11";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "nvme12";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "nvme13";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "nvme14";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "nvme15";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nvme16";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "nvme17";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "nvme18";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nvme19";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "nvme20";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "nvme21";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "nvme22";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "nvme23";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&xdma {
+	status = "okay";
+	memory-region = <&vga_memory>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+#include "ibm-power11-quad.dtsi"
-- 
2.39.3

[PATCH v3 13/14] ARM: dts: aspeed: Add IBM P11 Blueridge BMC system

[Krzysztof Kozlowski]

On 25/04/2024 23:37, Eddie James wrote:
> Add the device tree for the new BMC system. The Blueridge is a
> P11 system with four processors.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++++++++++++
>  1 file changed, 1711 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
> 
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
> new file mode 100644
> index 000000000000..8503ce2480b5
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
> @@ -0,0 +1,1711 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2024 IBM Corp.
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/i2c/i2c.h>
> +#include <dt-bindings/leds/leds-pca955x.h>
> +
> +/ {
> +	model = "Blueridge";
> +	compatible = "ibm,blueridge-bmc", "aspeed,ast2600";
> +
> +	aliases {
> +		serial4 = &uart5;
> +		i2c16 = &i2c2mux0;
> +		i2c17 = &i2c2mux1;
> +		i2c18 = &i2c2mux2;
> +		i2c19 = &i2c2mux3;
> +		i2c20 = &i2c4mux0chn0;
> +		i2c21 = &i2c4mux0chn1;
> +		i2c22 = &i2c4mux0chn2;
> +		i2c23 = &i2c5mux0chn0;
> +		i2c24 = &i2c5mux0chn1;
> +		i2c25 = &i2c6mux0chn0;
> +		i2c26 = &i2c6mux0chn1;
> +		i2c27 = &i2c6mux0chn2;
> +		i2c28 = &i2c6mux0chn3;
> +		i2c29 = &i2c11mux0chn0;
> +		i2c30 = &i2c11mux0chn1;
> +	};
> +
> +	chosen {
> +		stdout-path = &uart5;
> +		bootargs = "console=ttyS4,115200n8 earlycon";

Drop bootargs. ALWAYS.


> +	};
> +
> +	memory at 80000000 {
> +		device_type = "memory";
> +		reg = <0x80000000 0x40000000>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		event_log: tcg_event_log at b3d00000 {

No underscores.

Didn't you already received such basic review?


> +			no-map;
> +			reg = <0xb3d00000 0x100000>;
> +		};
> +
> +		ramoops at b3e00000 {
> +			compatible = "ramoops";
> +			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
> +			record-size = <0x8000>;
> +			console-size = <0x8000>;
> +			ftrace-size = <0x8000>;
> +			pmsg-size = <0x8000>;
> +			max-reason = <3>; /* KMSG_DUMP_EMERG */
> +		};
> +
> +		/* LPC FW cycle bridge region requires natural alignment */
> +		flash_memory: region at b4000000 {
> +			no-map;
> +			reg = <0xb4000000 0x04000000>; /* 64M */
> +		};
> +
> +		/* VGA region is dictated by hardware strapping */
> +		vga_memory: region at bf000000 {
> +			no-map;
> +			compatible = "shared-dma-pool";
> +			reg = <0xbf000000 0x01000000>;  /* 16M */
> +		};
> +	};
> +
> +	i2c2mux: i2cmux {
> +		compatible = "i2c-mux-gpio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";

??? Drop


> +
> +		i2c-parent = <&i2c2>;
> +		mux-gpios = <&gpio0 ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>,
> +			    <&gpio0 ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
> +		idle-state = <0>;
> +
> +		i2c2mux0: i2c at 0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0>;
> +		};
> +
> +		i2c2mux1: i2c at 1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <1>;
> +		};
> +
> +		i2c2mux2: i2c at 2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <2>;
> +		};
> +
> +		i2c2mux3: i2c at 3 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <3>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		/* BMC Card fault LED at the back */
> +		led-bmc-ingraham0 {
> +			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		/* Enclosure ID LED at the back */
> +		led-rear-enc-id0 {
> +			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		/* Enclosure fault LED at the back */
> +		led-rear-enc-fault0 {
> +			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		/* PCIE slot power LED */
> +		led-pcieslot-power {
> +			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	gpio-keys-polled {
> +		compatible = "gpio-keys-polled";
> +		poll-interval = <1000>;
> +
> +		event-fan0-presence {
> +			label = "fan0-presence";
> +			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
> +			linux,code = <6>;
> +		};
> +
> +		event-fan1-presence {
> +			label = "fan1-presence";
> +			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
> +			linux,code = <7>;
> +		};
> +
> +		event-fan2-presence {
> +			label = "fan2-presence";
> +			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
> +			linux,code = <8>;
> +		};
> +
> +		event-fan3-presence {
> +			label = "fan3-presence";
> +			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
> +			linux,code = <9>;
> +		};
> +
> +		event-fan4-presence {
> +			label = "fan4-presence";
> +			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
> +			linux,code = <10>;
> +		};
> +
> +		event-fan5-presence {
> +			label = "fan5-presence";
> +			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
> +			linux,code = <11>;
> +		};
> +	};
> +
> +	iio-hwmon {
> +		compatible = "iio-hwmon";
> +		io-channels = <&adc1 7>;
> +	};
> +};
> +
> +&adc1 {
> +	status = "okay";
> +	aspeed,int-vref-microvolt = <2500000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
> +		&pinctrl_adc10_default &pinctrl_adc11_default
> +		&pinctrl_adc12_default &pinctrl_adc13_default
> +		&pinctrl_adc14_default &pinctrl_adc15_default>;
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&uhci {
> +	status = "okay";
> +};
> +
> +&gpio0 {
> +	gpio-line-names =
> +	/*A0-A7*/	"","","","","","","","",
> +	/*B0-B7*/	"","","","","","","checkstop","",
> +	/*C0-C7*/	"","","","","","","","",
> +	/*D0-D7*/	"","","","","","","","",
> +	/*E0-E7*/	"","","","","","","","",
> +	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
> +	/*G0-G7*/	"","","","","","","","",
> +	/*H0-H7*/	"","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
> +	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
> +	/*J0-J7*/	"","","","","","","","",
> +	/*K0-K7*/	"","","","","","","","",
> +	/*L0-L7*/	"","","","","","","","",
> +	/*M0-M7*/	"","","","","","","","",
> +	/*N0-N7*/	"","","","","","","","",
> +	/*O0-O7*/	"","","","usb-power","","","","",
> +	/*P0-P7*/	"","","","","pcieslot-power","","","",
> +	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
> +	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
> +	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
> +	"power-ffs-sync-history","","","",
> +	/*T0-T7*/	"","","","","","","","",
> +	/*U0-U7*/	"","","","","","","","",
> +	/*V0-V7*/	"","","","","","","","",
> +	/*W0-W7*/	"","","","","","","","",
> +	/*X0-X7*/	"","","","","","","","",
> +	/*Y0-Y7*/	"","","","","","","","",
> +	/*Z0-Z7*/	"","","","","","","","";
> +
> +	i2c3_mux_oe_n-hog {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
> +		output-high;
> +		line-name = "I2C3_MUX_OE_N";
> +	};
> +
> +	usb_power-hog {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
> +		output-high;
> +	};
> +};
> +
> +&emmc_controller {
> +	status = "okay";
> +};
> +
> +&pinctrl_emmc_default {
> +	bias-disable;
> +};
> +
> +&emmc {
> +	status = "okay";
> +	clk-phase-mmc-hs200 = <180>, <180>;
> +};
> +
> +&ibt {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	eeprom at 51 {
> +		compatible = "atmel,24c64";
> +		reg = <0x51>;
> +	};
> +
> +	tca_pres1: tca9554 at 20{

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

Also missing space before {


> +		compatible = "ti,tca9554";
> +		reg = <0x20>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		gpio-line-names = "",
> +			"RUSSEL_FW_I2C_ENABLE_N",
> +			"RUSSEL_OPPANEL_PRESENCE_N",
> +			"BLYTH_OPPANEL_PRESENCE_N",
> +			"CPU_TPM_CARD_PRESENT_N",
> +			"DASD_BP2_PRESENT_N",
> +			"DASD_BP1_PRESENT_N",
> +			"DASD_BP0_PRESENT_N";
> +	};
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +};
> +
> +&i2c2 {
> +	status = "okay";
> +};
> +
> +&i2c3 {
> +	status = "okay";
> +
> +	power-supply at 68 {
> +		compatible = "ibm,cffps";
> +		reg = <0x68>;
> +	};
> +
> +	power-supply at 69 {
> +		compatible = "ibm,cffps";
> +		reg = <0x69>;
> +	};
> +
> +	pca_pres1: pca9552 at 61 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +		compatible = "nxp,pca9552";
> +		reg = <0x61>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		gpio-line-names =
> +			"SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD",
> +			"SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD",
> +			"SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N",
> +			"SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N",
> +			"SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N",
> +			"", "", "", "", "", "";
> +	};
> +};
> +
> +&i2c4 {
> +	status = "okay";
> +
> +	tmp275 at 48 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation



> +		compatible = "ti,tmp275";
> +		reg = <0x48>;
> +	};
> +
> +	tmp275 at 49 {

So it's everywhere...

> +		compatible = "ti,tmp275";
> +		reg = <0x49>;
> +	};
> +
> +	tmp275 at 4a {
> +		compatible = "ti,tmp275";
> +		reg = <0x4a>;
> +	};
> +
> +	i2c-mux at 70 {
> +		compatible = "nxp,pca9546";
> +		reg = <0x70>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";

Why? Drop

> +		i2c-mux-idle-disconnect;
> +
> +		i2c4mux0chn0: i2c at 0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0>;
> +
> +			eeprom at 50 {
> +				compatible = "atmel,24c64";
> +				reg = <0x50>;
> +			};
> +
> +			pca9551 at 60 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +				compatible = "nxp,pca9551";
> +				reg = <0x60>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +
> +				led at 0 {
> +					label = "cablecard0-cxp-top";
> +					reg = <0>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +
> +				led at 1 {
> +					label = "cablecard0-cxp-bot";
> +					reg = <1>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +			};
> +		};
> +
> +		i2c4mux0chn1: i2c at 1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <1>;

reg is after compatible, which means if there is no compatible, reg is
always first. This applies you all your DTS patches. This patchset and
future.


> +
> +			eeprom at 51 {
> +				compatible = "atmel,24c64";
> +				reg = <0x51>;
> +			};
> +		};
> +
> +		i2c4mux0chn2: i2c at 2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <2>;
> +
> +			eeprom at 52 {
> +				compatible = "atmel,24c64";
> +				reg = <0x52>;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c5 {
> +	status = "okay";
> +
> +	tmp275 at 48 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +		compatible = "ti,tmp275";
> +		reg = <0x48>;
> +	};
> +
> +	tmp275 at 49 {
> +		compatible = "ti,tmp275";
> +		reg = <0x49>;
> +	};
> +
> +	i2c-mux at 70 {
> +		compatible = "nxp,pca9546";
> +		reg = <0x70>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";

Drop


> +		i2c-mux-idle-disconnect;
> +
> +		i2c5mux0chn0: i2c at 0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0>;
> +
> +			eeprom at 50 {
> +				compatible = "atmel,24c64";
> +				reg = <0x50>;
> +			};
> +
> +			pca9551 at 60 {
> +				compatible = "nxp,pca9551";
> +				reg = <0x60>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +
> +				led at 0 {
> +					label = "cablecard3-cxp-top";
> +					reg = <0>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +
> +				led at 1 {
> +					label = "cablecard3-cxp-bot";
> +					reg = <1>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +			};
> +		};
> +
> +		i2c5mux0chn1: i2c at 1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <1>;
> +
> +			eeprom at 51 {
> +				compatible = "atmel,24c64";
> +				reg = <0x51>;
> +			};
> +
> +			pca9551 at 61 {
> +				compatible = "nxp,pca9551";
> +				reg = <0x61>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;


And here you have correct order of properties...



Best regards,
Krzysztof

Re: [PATCH v3 13/14] ARM: dts: aspeed: Add IBM P11 Blueridge BMC system

[Krzysztof Kozlowski]

On 25/04/2024 23:37, Eddie James wrote:
> Add the device tree for the new BMC system. The Blueridge is a
> P11 system with four processors.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++++++++++++
>  1 file changed, 1711 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
> 
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
> new file mode 100644
> index 000000000000..8503ce2480b5
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
> @@ -0,0 +1,1711 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2024 IBM Corp.
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/i2c/i2c.h>
> +#include <dt-bindings/leds/leds-pca955x.h>
> +
> +/ {
> +	model = "Blueridge";
> +	compatible = "ibm,blueridge-bmc", "aspeed,ast2600";
> +
> +	aliases {
> +		serial4 = &uart5;
> +		i2c16 = &i2c2mux0;
> +		i2c17 = &i2c2mux1;
> +		i2c18 = &i2c2mux2;
> +		i2c19 = &i2c2mux3;
> +		i2c20 = &i2c4mux0chn0;
> +		i2c21 = &i2c4mux0chn1;
> +		i2c22 = &i2c4mux0chn2;
> +		i2c23 = &i2c5mux0chn0;
> +		i2c24 = &i2c5mux0chn1;
> +		i2c25 = &i2c6mux0chn0;
> +		i2c26 = &i2c6mux0chn1;
> +		i2c27 = &i2c6mux0chn2;
> +		i2c28 = &i2c6mux0chn3;
> +		i2c29 = &i2c11mux0chn0;
> +		i2c30 = &i2c11mux0chn1;
> +	};
> +
> +	chosen {
> +		stdout-path = &uart5;
> +		bootargs = "console=ttyS4,115200n8 earlycon";

Drop bootargs. ALWAYS.


> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		reg = <0x80000000 0x40000000>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		event_log: tcg_event_log@b3d00000 {

No underscores.

Didn't you already received such basic review?


> +			no-map;
> +			reg = <0xb3d00000 0x100000>;
> +		};
> +
> +		ramoops@b3e00000 {
> +			compatible = "ramoops";
> +			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
> +			record-size = <0x8000>;
> +			console-size = <0x8000>;
> +			ftrace-size = <0x8000>;
> +			pmsg-size = <0x8000>;
> +			max-reason = <3>; /* KMSG_DUMP_EMERG */
> +		};
> +
> +		/* LPC FW cycle bridge region requires natural alignment */
> +		flash_memory: region@b4000000 {
> +			no-map;
> +			reg = <0xb4000000 0x04000000>; /* 64M */
> +		};
> +
> +		/* VGA region is dictated by hardware strapping */
> +		vga_memory: region@bf000000 {
> +			no-map;
> +			compatible = "shared-dma-pool";
> +			reg = <0xbf000000 0x01000000>;  /* 16M */
> +		};
> +	};
> +
> +	i2c2mux: i2cmux {
> +		compatible = "i2c-mux-gpio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";

??? Drop


> +
> +		i2c-parent = <&i2c2>;
> +		mux-gpios = <&gpio0 ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>,
> +			    <&gpio0 ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
> +		idle-state = <0>;
> +
> +		i2c2mux0: i2c@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0>;
> +		};
> +
> +		i2c2mux1: i2c@1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <1>;
> +		};
> +
> +		i2c2mux2: i2c@2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <2>;
> +		};
> +
> +		i2c2mux3: i2c@3 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <3>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		/* BMC Card fault LED at the back */
> +		led-bmc-ingraham0 {
> +			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		/* Enclosure ID LED at the back */
> +		led-rear-enc-id0 {
> +			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		/* Enclosure fault LED at the back */
> +		led-rear-enc-fault0 {
> +			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		/* PCIE slot power LED */
> +		led-pcieslot-power {
> +			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	gpio-keys-polled {
> +		compatible = "gpio-keys-polled";
> +		poll-interval = <1000>;
> +
> +		event-fan0-presence {
> +			label = "fan0-presence";
> +			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
> +			linux,code = <6>;
> +		};
> +
> +		event-fan1-presence {
> +			label = "fan1-presence";
> +			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
> +			linux,code = <7>;
> +		};
> +
> +		event-fan2-presence {
> +			label = "fan2-presence";
> +			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
> +			linux,code = <8>;
> +		};
> +
> +		event-fan3-presence {
> +			label = "fan3-presence";
> +			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
> +			linux,code = <9>;
> +		};
> +
> +		event-fan4-presence {
> +			label = "fan4-presence";
> +			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
> +			linux,code = <10>;
> +		};
> +
> +		event-fan5-presence {
> +			label = "fan5-presence";
> +			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
> +			linux,code = <11>;
> +		};
> +	};
> +
> +	iio-hwmon {
> +		compatible = "iio-hwmon";
> +		io-channels = <&adc1 7>;
> +	};
> +};
> +
> +&adc1 {
> +	status = "okay";
> +	aspeed,int-vref-microvolt = <2500000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
> +		&pinctrl_adc10_default &pinctrl_adc11_default
> +		&pinctrl_adc12_default &pinctrl_adc13_default
> +		&pinctrl_adc14_default &pinctrl_adc15_default>;
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&uhci {
> +	status = "okay";
> +};
> +
> +&gpio0 {
> +	gpio-line-names =
> +	/*A0-A7*/	"","","","","","","","",
> +	/*B0-B7*/	"","","","","","","checkstop","",
> +	/*C0-C7*/	"","","","","","","","",
> +	/*D0-D7*/	"","","","","","","","",
> +	/*E0-E7*/	"","","","","","","","",
> +	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
> +	/*G0-G7*/	"","","","","","","","",
> +	/*H0-H7*/	"","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
> +	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
> +	/*J0-J7*/	"","","","","","","","",
> +	/*K0-K7*/	"","","","","","","","",
> +	/*L0-L7*/	"","","","","","","","",
> +	/*M0-M7*/	"","","","","","","","",
> +	/*N0-N7*/	"","","","","","","","",
> +	/*O0-O7*/	"","","","usb-power","","","","",
> +	/*P0-P7*/	"","","","","pcieslot-power","","","",
> +	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
> +	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
> +	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
> +	"power-ffs-sync-history","","","",
> +	/*T0-T7*/	"","","","","","","","",
> +	/*U0-U7*/	"","","","","","","","",
> +	/*V0-V7*/	"","","","","","","","",
> +	/*W0-W7*/	"","","","","","","","",
> +	/*X0-X7*/	"","","","","","","","",
> +	/*Y0-Y7*/	"","","","","","","","",
> +	/*Z0-Z7*/	"","","","","","","","";
> +
> +	i2c3_mux_oe_n-hog {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
> +		output-high;
> +		line-name = "I2C3_MUX_OE_N";
> +	};
> +
> +	usb_power-hog {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
> +		output-high;
> +	};
> +};
> +
> +&emmc_controller {
> +	status = "okay";
> +};
> +
> +&pinctrl_emmc_default {
> +	bias-disable;
> +};
> +
> +&emmc {
> +	status = "okay";
> +	clk-phase-mmc-hs200 = <180>, <180>;
> +};
> +
> +&ibt {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	eeprom@51 {
> +		compatible = "atmel,24c64";
> +		reg = <0x51>;
> +	};
> +
> +	tca_pres1: tca9554@20{

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

Also missing space before {


> +		compatible = "ti,tca9554";
> +		reg = <0x20>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		gpio-line-names = "",
> +			"RUSSEL_FW_I2C_ENABLE_N",
> +			"RUSSEL_OPPANEL_PRESENCE_N",
> +			"BLYTH_OPPANEL_PRESENCE_N",
> +			"CPU_TPM_CARD_PRESENT_N",
> +			"DASD_BP2_PRESENT_N",
> +			"DASD_BP1_PRESENT_N",
> +			"DASD_BP0_PRESENT_N";
> +	};
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +};
> +
> +&i2c2 {
> +	status = "okay";
> +};
> +
> +&i2c3 {
> +	status = "okay";
> +
> +	power-supply@68 {
> +		compatible = "ibm,cffps";
> +		reg = <0x68>;
> +	};
> +
> +	power-supply@69 {
> +		compatible = "ibm,cffps";
> +		reg = <0x69>;
> +	};
> +
> +	pca_pres1: pca9552@61 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +		compatible = "nxp,pca9552";
> +		reg = <0x61>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		gpio-line-names =
> +			"SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD",
> +			"SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD",
> +			"SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N",
> +			"SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N",
> +			"SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N",
> +			"", "", "", "", "", "";
> +	};
> +};
> +
> +&i2c4 {
> +	status = "okay";
> +
> +	tmp275@48 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation



> +		compatible = "ti,tmp275";
> +		reg = <0x48>;
> +	};
> +
> +	tmp275@49 {

So it's everywhere...

> +		compatible = "ti,tmp275";
> +		reg = <0x49>;
> +	};
> +
> +	tmp275@4a {
> +		compatible = "ti,tmp275";
> +		reg = <0x4a>;
> +	};
> +
> +	i2c-mux@70 {
> +		compatible = "nxp,pca9546";
> +		reg = <0x70>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";

Why? Drop

> +		i2c-mux-idle-disconnect;
> +
> +		i2c4mux0chn0: i2c@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0>;
> +
> +			eeprom@50 {
> +				compatible = "atmel,24c64";
> +				reg = <0x50>;
> +			};
> +
> +			pca9551@60 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +				compatible = "nxp,pca9551";
> +				reg = <0x60>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +
> +				led@0 {
> +					label = "cablecard0-cxp-top";
> +					reg = <0>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +
> +				led@1 {
> +					label = "cablecard0-cxp-bot";
> +					reg = <1>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +			};
> +		};
> +
> +		i2c4mux0chn1: i2c@1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <1>;

reg is after compatible, which means if there is no compatible, reg is
always first. This applies you all your DTS patches. This patchset and
future.


> +
> +			eeprom@51 {
> +				compatible = "atmel,24c64";
> +				reg = <0x51>;
> +			};
> +		};
> +
> +		i2c4mux0chn2: i2c@2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <2>;
> +
> +			eeprom@52 {
> +				compatible = "atmel,24c64";
> +				reg = <0x52>;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c5 {
> +	status = "okay";
> +
> +	tmp275@48 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +		compatible = "ti,tmp275";
> +		reg = <0x48>;
> +	};
> +
> +	tmp275@49 {
> +		compatible = "ti,tmp275";
> +		reg = <0x49>;
> +	};
> +
> +	i2c-mux@70 {
> +		compatible = "nxp,pca9546";
> +		reg = <0x70>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";

Drop


> +		i2c-mux-idle-disconnect;
> +
> +		i2c5mux0chn0: i2c@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0>;
> +
> +			eeprom@50 {
> +				compatible = "atmel,24c64";
> +				reg = <0x50>;
> +			};
> +
> +			pca9551@60 {
> +				compatible = "nxp,pca9551";
> +				reg = <0x60>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +
> +				led@0 {
> +					label = "cablecard3-cxp-top";
> +					reg = <0>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +
> +				led@1 {
> +					label = "cablecard3-cxp-bot";
> +					reg = <1>;
> +					retain-state-shutdown;
> +					default-state = "keep";
> +					type = <PCA955X_TYPE_LED>;
> +				};
> +			};
> +		};
> +
> +		i2c5mux0chn1: i2c@1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <1>;
> +
> +			eeprom@51 {
> +				compatible = "atmel,24c64";
> +				reg = <0x51>;
> +			};
> +
> +			pca9551@61 {
> +				compatible = "nxp,pca9551";
> +				reg = <0x61>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;


And here you have correct order of properties...



Best regards,
Krzysztof

[PATCH v3 13/14] ARM: dts: aspeed: Add IBM P11 Blueridge BMC system

[Eddie James]

On 4/26/24 01:35, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:37, Eddie James wrote:
>> Add the device tree for the new BMC system. The Blueridge is a
>> P11 system with four processors.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++++++++++++
>>   1 file changed, 1711 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
>>
>> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
>> new file mode 100644
>> index 000000000000..8503ce2480b5
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
>> @@ -0,0 +1,1711 @@
>> +// SPDX-License-Identifier: GPL-2.0-or-later
>> +// Copyright 2024 IBM Corp.
>> +/dts-v1/;
>> +
>> +#include "aspeed-g6.dtsi"
>> +#include <dt-bindings/gpio/aspeed-gpio.h>
>> +#include <dt-bindings/i2c/i2c.h>
>> +#include <dt-bindings/leds/leds-pca955x.h>
>> +
>> +/ {
>> +	model = "Blueridge";
>> +	compatible = "ibm,blueridge-bmc", "aspeed,ast2600";
>> +
>> +	aliases {
>> +		serial4 = &uart5;
>> +		i2c16 = &i2c2mux0;
>> +		i2c17 = &i2c2mux1;
>> +		i2c18 = &i2c2mux2;
>> +		i2c19 = &i2c2mux3;
>> +		i2c20 = &i2c4mux0chn0;
>> +		i2c21 = &i2c4mux0chn1;
>> +		i2c22 = &i2c4mux0chn2;
>> +		i2c23 = &i2c5mux0chn0;
>> +		i2c24 = &i2c5mux0chn1;
>> +		i2c25 = &i2c6mux0chn0;
>> +		i2c26 = &i2c6mux0chn1;
>> +		i2c27 = &i2c6mux0chn2;
>> +		i2c28 = &i2c6mux0chn3;
>> +		i2c29 = &i2c11mux0chn0;
>> +		i2c30 = &i2c11mux0chn1;
>> +	};
>> +
>> +	chosen {
>> +		stdout-path = &uart5;
>> +		bootargs = "console=ttyS4,115200n8 earlycon";
> Drop bootargs. ALWAYS.
>
>
>> +	};
>> +
>> +	memory at 80000000 {
>> +		device_type = "memory";
>> +		reg = <0x80000000 0x40000000>;
>> +	};
>> +
>> +	reserved-memory {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		event_log: tcg_event_log at b3d00000 {
> No underscores.
>
> Didn't you already received such basic review?


Thanks for your detailed review Krzysztof. These device trees are based 
off 5 year old device trees that were merged when the rules were much 
less strict. I will attempt to address all of your comments for these 
new dts.


Thanks,

Eddie


>
>
>> +			no-map;
>> +			reg = <0xb3d00000 0x100000>;
>> +		};
>> +
>> +		ramoops at b3e00000 {
>> +			compatible = "ramoops";
>> +			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
>> +			record-size = <0x8000>;
>> +			console-size = <0x8000>;
>> +			ftrace-size = <0x8000>;
>> +			pmsg-size = <0x8000>;
>> +			max-reason = <3>; /* KMSG_DUMP_EMERG */
>> +		};
>> +
>> +		/* LPC FW cycle bridge region requires natural alignment */
>> +		flash_memory: region at b4000000 {
>> +			no-map;
>> +			reg = <0xb4000000 0x04000000>; /* 64M */
>> +		};
>> +
>> +		/* VGA region is dictated by hardware strapping */
>> +		vga_memory: region at bf000000 {
>> +			no-map;
>> +			compatible = "shared-dma-pool";
>> +			reg = <0xbf000000 0x01000000>;  /* 16M */
>> +		};
>> +	};
>> +
>> +	i2c2mux: i2cmux {
>> +		compatible = "i2c-mux-gpio";
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		status = "okay";
> ??? Drop
>
>
>> +
>> +		i2c-parent = <&i2c2>;
>> +		mux-gpios = <&gpio0 ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>,
>> +			    <&gpio0 ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
>> +		idle-state = <0>;
>> +
>> +		i2c2mux0: i2c at 0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0>;
>> +		};
>> +
>> +		i2c2mux1: i2c at 1 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <1>;
>> +		};
>> +
>> +		i2c2mux2: i2c at 2 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <2>;
>> +		};
>> +
>> +		i2c2mux3: i2c at 3 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <3>;
>> +		};
>> +	};
>> +
>> +	leds {
>> +		compatible = "gpio-leds";
>> +
>> +		/* BMC Card fault LED at the back */
>> +		led-bmc-ingraham0 {
>> +			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		/* Enclosure ID LED at the back */
>> +		led-rear-enc-id0 {
>> +			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		/* Enclosure fault LED at the back */
>> +		led-rear-enc-fault0 {
>> +			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		/* PCIE slot power LED */
>> +		led-pcieslot-power {
>> +			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
>> +		};
>> +	};
>> +
>> +	gpio-keys-polled {
>> +		compatible = "gpio-keys-polled";
>> +		poll-interval = <1000>;
>> +
>> +		event-fan0-presence {
>> +			label = "fan0-presence";
>> +			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
>> +			linux,code = <6>;
>> +		};
>> +
>> +		event-fan1-presence {
>> +			label = "fan1-presence";
>> +			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
>> +			linux,code = <7>;
>> +		};
>> +
>> +		event-fan2-presence {
>> +			label = "fan2-presence";
>> +			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
>> +			linux,code = <8>;
>> +		};
>> +
>> +		event-fan3-presence {
>> +			label = "fan3-presence";
>> +			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
>> +			linux,code = <9>;
>> +		};
>> +
>> +		event-fan4-presence {
>> +			label = "fan4-presence";
>> +			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
>> +			linux,code = <10>;
>> +		};
>> +
>> +		event-fan5-presence {
>> +			label = "fan5-presence";
>> +			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
>> +			linux,code = <11>;
>> +		};
>> +	};
>> +
>> +	iio-hwmon {
>> +		compatible = "iio-hwmon";
>> +		io-channels = <&adc1 7>;
>> +	};
>> +};
>> +
>> +&adc1 {
>> +	status = "okay";
>> +	aspeed,int-vref-microvolt = <2500000>;
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
>> +		&pinctrl_adc10_default &pinctrl_adc11_default
>> +		&pinctrl_adc12_default &pinctrl_adc13_default
>> +		&pinctrl_adc14_default &pinctrl_adc15_default>;
>> +};
>> +
>> +&ehci1 {
>> +	status = "okay";
>> +};
>> +
>> +&uhci {
>> +	status = "okay";
>> +};
>> +
>> +&gpio0 {
>> +	gpio-line-names =
>> +	/*A0-A7*/	"","","","","","","","",
>> +	/*B0-B7*/	"","","","","","","checkstop","",
>> +	/*C0-C7*/	"","","","","","","","",
>> +	/*D0-D7*/	"","","","","","","","",
>> +	/*E0-E7*/	"","","","","","","","",
>> +	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
>> +	/*G0-G7*/	"","","","","","","","",
>> +	/*H0-H7*/	"","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
>> +	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
>> +	/*J0-J7*/	"","","","","","","","",
>> +	/*K0-K7*/	"","","","","","","","",
>> +	/*L0-L7*/	"","","","","","","","",
>> +	/*M0-M7*/	"","","","","","","","",
>> +	/*N0-N7*/	"","","","","","","","",
>> +	/*O0-O7*/	"","","","usb-power","","","","",
>> +	/*P0-P7*/	"","","","","pcieslot-power","","","",
>> +	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
>> +	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
>> +	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
>> +	"power-ffs-sync-history","","","",
>> +	/*T0-T7*/	"","","","","","","","",
>> +	/*U0-U7*/	"","","","","","","","",
>> +	/*V0-V7*/	"","","","","","","","",
>> +	/*W0-W7*/	"","","","","","","","",
>> +	/*X0-X7*/	"","","","","","","","",
>> +	/*Y0-Y7*/	"","","","","","","","",
>> +	/*Z0-Z7*/	"","","","","","","","";
>> +
>> +	i2c3_mux_oe_n-hog {
>> +		gpio-hog;
>> +		gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
>> +		output-high;
>> +		line-name = "I2C3_MUX_OE_N";
>> +	};
>> +
>> +	usb_power-hog {
>> +		gpio-hog;
>> +		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
>> +		output-high;
>> +	};
>> +};
>> +
>> +&emmc_controller {
>> +	status = "okay";
>> +};
>> +
>> +&pinctrl_emmc_default {
>> +	bias-disable;
>> +};
>> +
>> +&emmc {
>> +	status = "okay";
>> +	clk-phase-mmc-hs200 = <180>, <180>;
>> +};
>> +
>> +&ibt {
>> +	status = "okay";
>> +};
>> +
>> +&i2c0 {
>> +	status = "okay";
>> +
>> +	eeprom at 51 {
>> +		compatible = "atmel,24c64";
>> +		reg = <0x51>;
>> +	};
>> +
>> +	tca_pres1: tca9554 at 20{
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
> Also missing space before {
>
>
>> +		compatible = "ti,tca9554";
>> +		reg = <0x20>;
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		gpio-line-names = "",
>> +			"RUSSEL_FW_I2C_ENABLE_N",
>> +			"RUSSEL_OPPANEL_PRESENCE_N",
>> +			"BLYTH_OPPANEL_PRESENCE_N",
>> +			"CPU_TPM_CARD_PRESENT_N",
>> +			"DASD_BP2_PRESENT_N",
>> +			"DASD_BP1_PRESENT_N",
>> +			"DASD_BP0_PRESENT_N";
>> +	};
>> +};
>> +
>> +&i2c1 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c2 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c3 {
>> +	status = "okay";
>> +
>> +	power-supply at 68 {
>> +		compatible = "ibm,cffps";
>> +		reg = <0x68>;
>> +	};
>> +
>> +	power-supply at 69 {
>> +		compatible = "ibm,cffps";
>> +		reg = <0x69>;
>> +	};
>> +
>> +	pca_pres1: pca9552 at 61 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
>
>> +		compatible = "nxp,pca9552";
>> +		reg = <0x61>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		gpio-line-names =
>> +			"SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD",
>> +			"SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD",
>> +			"SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N",
>> +			"SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N",
>> +			"SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N",
>> +			"", "", "", "", "", "";
>> +	};
>> +};
>> +
>> +&i2c4 {
>> +	status = "okay";
>> +
>> +	tmp275 at 48 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
>
>
>> +		compatible = "ti,tmp275";
>> +		reg = <0x48>;
>> +	};
>> +
>> +	tmp275 at 49 {
> So it's everywhere...
>
>> +		compatible = "ti,tmp275";
>> +		reg = <0x49>;
>> +	};
>> +
>> +	tmp275 at 4a {
>> +		compatible = "ti,tmp275";
>> +		reg = <0x4a>;
>> +	};
>> +
>> +	i2c-mux at 70 {
>> +		compatible = "nxp,pca9546";
>> +		reg = <0x70>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		status = "okay";
> Why? Drop
>
>> +		i2c-mux-idle-disconnect;
>> +
>> +		i2c4mux0chn0: i2c at 0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0>;
>> +
>> +			eeprom at 50 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x50>;
>> +			};
>> +
>> +			pca9551 at 60 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
>
>> +				compatible = "nxp,pca9551";
>> +				reg = <0x60>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				gpio-controller;
>> +				#gpio-cells = <2>;
>> +
>> +				led at 0 {
>> +					label = "cablecard0-cxp-top";
>> +					reg = <0>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +
>> +				led at 1 {
>> +					label = "cablecard0-cxp-bot";
>> +					reg = <1>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +			};
>> +		};
>> +
>> +		i2c4mux0chn1: i2c at 1 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <1>;
> reg is after compatible, which means if there is no compatible, reg is
> always first. This applies you all your DTS patches. This patchset and
> future.
>
>
>> +
>> +			eeprom at 51 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x51>;
>> +			};
>> +		};
>> +
>> +		i2c4mux0chn2: i2c at 2 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <2>;
>> +
>> +			eeprom at 52 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x52>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&i2c5 {
>> +	status = "okay";
>> +
>> +	tmp275 at 48 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
>
>> +		compatible = "ti,tmp275";
>> +		reg = <0x48>;
>> +	};
>> +
>> +	tmp275 at 49 {
>> +		compatible = "ti,tmp275";
>> +		reg = <0x49>;
>> +	};
>> +
>> +	i2c-mux at 70 {
>> +		compatible = "nxp,pca9546";
>> +		reg = <0x70>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		status = "okay";
> Drop
>
>
>> +		i2c-mux-idle-disconnect;
>> +
>> +		i2c5mux0chn0: i2c at 0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0>;
>> +
>> +			eeprom at 50 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x50>;
>> +			};
>> +
>> +			pca9551 at 60 {
>> +				compatible = "nxp,pca9551";
>> +				reg = <0x60>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				gpio-controller;
>> +				#gpio-cells = <2>;
>> +
>> +				led at 0 {
>> +					label = "cablecard3-cxp-top";
>> +					reg = <0>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +
>> +				led at 1 {
>> +					label = "cablecard3-cxp-bot";
>> +					reg = <1>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +			};
>> +		};
>> +
>> +		i2c5mux0chn1: i2c at 1 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <1>;
>> +
>> +			eeprom at 51 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x51>;
>> +			};
>> +
>> +			pca9551 at 61 {
>> +				compatible = "nxp,pca9551";
>> +				reg = <0x61>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>
> And here you have correct order of properties...
>
>
>
> Best regards,
> Krzysztof
>

Re: [PATCH v3 13/14] ARM: dts: aspeed: Add IBM P11 Blueridge BMC system

[Eddie James]

On 4/26/24 01:35, Krzysztof Kozlowski wrote:
> On 25/04/2024 23:37, Eddie James wrote:
>> Add the device tree for the new BMC system. The Blueridge is a
>> P11 system with four processors.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++++++++++++
>>   1 file changed, 1711 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
>>
>> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
>> new file mode 100644
>> index 000000000000..8503ce2480b5
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
>> @@ -0,0 +1,1711 @@
>> +// SPDX-License-Identifier: GPL-2.0-or-later
>> +// Copyright 2024 IBM Corp.
>> +/dts-v1/;
>> +
>> +#include "aspeed-g6.dtsi"
>> +#include <dt-bindings/gpio/aspeed-gpio.h>
>> +#include <dt-bindings/i2c/i2c.h>
>> +#include <dt-bindings/leds/leds-pca955x.h>
>> +
>> +/ {
>> +	model = "Blueridge";
>> +	compatible = "ibm,blueridge-bmc", "aspeed,ast2600";
>> +
>> +	aliases {
>> +		serial4 = &uart5;
>> +		i2c16 = &i2c2mux0;
>> +		i2c17 = &i2c2mux1;
>> +		i2c18 = &i2c2mux2;
>> +		i2c19 = &i2c2mux3;
>> +		i2c20 = &i2c4mux0chn0;
>> +		i2c21 = &i2c4mux0chn1;
>> +		i2c22 = &i2c4mux0chn2;
>> +		i2c23 = &i2c5mux0chn0;
>> +		i2c24 = &i2c5mux0chn1;
>> +		i2c25 = &i2c6mux0chn0;
>> +		i2c26 = &i2c6mux0chn1;
>> +		i2c27 = &i2c6mux0chn2;
>> +		i2c28 = &i2c6mux0chn3;
>> +		i2c29 = &i2c11mux0chn0;
>> +		i2c30 = &i2c11mux0chn1;
>> +	};
>> +
>> +	chosen {
>> +		stdout-path = &uart5;
>> +		bootargs = "console=ttyS4,115200n8 earlycon";
> Drop bootargs. ALWAYS.
>
>
>> +	};
>> +
>> +	memory@80000000 {
>> +		device_type = "memory";
>> +		reg = <0x80000000 0x40000000>;
>> +	};
>> +
>> +	reserved-memory {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		event_log: tcg_event_log@b3d00000 {
> No underscores.
>
> Didn't you already received such basic review?


Thanks for your detailed review Krzysztof. These device trees are based 
off 5 year old device trees that were merged when the rules were much 
less strict. I will attempt to address all of your comments for these 
new dts.


Thanks,

Eddie


>
>
>> +			no-map;
>> +			reg = <0xb3d00000 0x100000>;
>> +		};
>> +
>> +		ramoops@b3e00000 {
>> +			compatible = "ramoops";
>> +			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
>> +			record-size = <0x8000>;
>> +			console-size = <0x8000>;
>> +			ftrace-size = <0x8000>;
>> +			pmsg-size = <0x8000>;
>> +			max-reason = <3>; /* KMSG_DUMP_EMERG */
>> +		};
>> +
>> +		/* LPC FW cycle bridge region requires natural alignment */
>> +		flash_memory: region@b4000000 {
>> +			no-map;
>> +			reg = <0xb4000000 0x04000000>; /* 64M */
>> +		};
>> +
>> +		/* VGA region is dictated by hardware strapping */
>> +		vga_memory: region@bf000000 {
>> +			no-map;
>> +			compatible = "shared-dma-pool";
>> +			reg = <0xbf000000 0x01000000>;  /* 16M */
>> +		};
>> +	};
>> +
>> +	i2c2mux: i2cmux {
>> +		compatible = "i2c-mux-gpio";
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		status = "okay";
> ??? Drop
>
>
>> +
>> +		i2c-parent = <&i2c2>;
>> +		mux-gpios = <&gpio0 ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>,
>> +			    <&gpio0 ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
>> +		idle-state = <0>;
>> +
>> +		i2c2mux0: i2c@0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0>;
>> +		};
>> +
>> +		i2c2mux1: i2c@1 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <1>;
>> +		};
>> +
>> +		i2c2mux2: i2c@2 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <2>;
>> +		};
>> +
>> +		i2c2mux3: i2c@3 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <3>;
>> +		};
>> +	};
>> +
>> +	leds {
>> +		compatible = "gpio-leds";
>> +
>> +		/* BMC Card fault LED at the back */
>> +		led-bmc-ingraham0 {
>> +			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		/* Enclosure ID LED at the back */
>> +		led-rear-enc-id0 {
>> +			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		/* Enclosure fault LED at the back */
>> +		led-rear-enc-fault0 {
>> +			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		/* PCIE slot power LED */
>> +		led-pcieslot-power {
>> +			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
>> +		};
>> +	};
>> +
>> +	gpio-keys-polled {
>> +		compatible = "gpio-keys-polled";
>> +		poll-interval = <1000>;
>> +
>> +		event-fan0-presence {
>> +			label = "fan0-presence";
>> +			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
>> +			linux,code = <6>;
>> +		};
>> +
>> +		event-fan1-presence {
>> +			label = "fan1-presence";
>> +			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
>> +			linux,code = <7>;
>> +		};
>> +
>> +		event-fan2-presence {
>> +			label = "fan2-presence";
>> +			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
>> +			linux,code = <8>;
>> +		};
>> +
>> +		event-fan3-presence {
>> +			label = "fan3-presence";
>> +			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
>> +			linux,code = <9>;
>> +		};
>> +
>> +		event-fan4-presence {
>> +			label = "fan4-presence";
>> +			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
>> +			linux,code = <10>;
>> +		};
>> +
>> +		event-fan5-presence {
>> +			label = "fan5-presence";
>> +			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
>> +			linux,code = <11>;
>> +		};
>> +	};
>> +
>> +	iio-hwmon {
>> +		compatible = "iio-hwmon";
>> +		io-channels = <&adc1 7>;
>> +	};
>> +};
>> +
>> +&adc1 {
>> +	status = "okay";
>> +	aspeed,int-vref-microvolt = <2500000>;
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
>> +		&pinctrl_adc10_default &pinctrl_adc11_default
>> +		&pinctrl_adc12_default &pinctrl_adc13_default
>> +		&pinctrl_adc14_default &pinctrl_adc15_default>;
>> +};
>> +
>> +&ehci1 {
>> +	status = "okay";
>> +};
>> +
>> +&uhci {
>> +	status = "okay";
>> +};
>> +
>> +&gpio0 {
>> +	gpio-line-names =
>> +	/*A0-A7*/	"","","","","","","","",
>> +	/*B0-B7*/	"","","","","","","checkstop","",
>> +	/*C0-C7*/	"","","","","","","","",
>> +	/*D0-D7*/	"","","","","","","","",
>> +	/*E0-E7*/	"","","","","","","","",
>> +	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
>> +	/*G0-G7*/	"","","","","","","","",
>> +	/*H0-H7*/	"","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
>> +	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
>> +	/*J0-J7*/	"","","","","","","","",
>> +	/*K0-K7*/	"","","","","","","","",
>> +	/*L0-L7*/	"","","","","","","","",
>> +	/*M0-M7*/	"","","","","","","","",
>> +	/*N0-N7*/	"","","","","","","","",
>> +	/*O0-O7*/	"","","","usb-power","","","","",
>> +	/*P0-P7*/	"","","","","pcieslot-power","","","",
>> +	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
>> +	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
>> +	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
>> +	"power-ffs-sync-history","","","",
>> +	/*T0-T7*/	"","","","","","","","",
>> +	/*U0-U7*/	"","","","","","","","",
>> +	/*V0-V7*/	"","","","","","","","",
>> +	/*W0-W7*/	"","","","","","","","",
>> +	/*X0-X7*/	"","","","","","","","",
>> +	/*Y0-Y7*/	"","","","","","","","",
>> +	/*Z0-Z7*/	"","","","","","","","";
>> +
>> +	i2c3_mux_oe_n-hog {
>> +		gpio-hog;
>> +		gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
>> +		output-high;
>> +		line-name = "I2C3_MUX_OE_N";
>> +	};
>> +
>> +	usb_power-hog {
>> +		gpio-hog;
>> +		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
>> +		output-high;
>> +	};
>> +};
>> +
>> +&emmc_controller {
>> +	status = "okay";
>> +};
>> +
>> +&pinctrl_emmc_default {
>> +	bias-disable;
>> +};
>> +
>> +&emmc {
>> +	status = "okay";
>> +	clk-phase-mmc-hs200 = <180>, <180>;
>> +};
>> +
>> +&ibt {
>> +	status = "okay";
>> +};
>> +
>> +&i2c0 {
>> +	status = "okay";
>> +
>> +	eeprom@51 {
>> +		compatible = "atmel,24c64";
>> +		reg = <0x51>;
>> +	};
>> +
>> +	tca_pres1: tca9554@20{
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
> Also missing space before {
>
>
>> +		compatible = "ti,tca9554";
>> +		reg = <0x20>;
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		gpio-line-names = "",
>> +			"RUSSEL_FW_I2C_ENABLE_N",
>> +			"RUSSEL_OPPANEL_PRESENCE_N",
>> +			"BLYTH_OPPANEL_PRESENCE_N",
>> +			"CPU_TPM_CARD_PRESENT_N",
>> +			"DASD_BP2_PRESENT_N",
>> +			"DASD_BP1_PRESENT_N",
>> +			"DASD_BP0_PRESENT_N";
>> +	};
>> +};
>> +
>> +&i2c1 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c2 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c3 {
>> +	status = "okay";
>> +
>> +	power-supply@68 {
>> +		compatible = "ibm,cffps";
>> +		reg = <0x68>;
>> +	};
>> +
>> +	power-supply@69 {
>> +		compatible = "ibm,cffps";
>> +		reg = <0x69>;
>> +	};
>> +
>> +	pca_pres1: pca9552@61 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
>
>> +		compatible = "nxp,pca9552";
>> +		reg = <0x61>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		gpio-line-names =
>> +			"SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD",
>> +			"SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD",
>> +			"SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N",
>> +			"SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N",
>> +			"SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N",
>> +			"", "", "", "", "", "";
>> +	};
>> +};
>> +
>> +&i2c4 {
>> +	status = "okay";
>> +
>> +	tmp275@48 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
>
>
>> +		compatible = "ti,tmp275";
>> +		reg = <0x48>;
>> +	};
>> +
>> +	tmp275@49 {
> So it's everywhere...
>
>> +		compatible = "ti,tmp275";
>> +		reg = <0x49>;
>> +	};
>> +
>> +	tmp275@4a {
>> +		compatible = "ti,tmp275";
>> +		reg = <0x4a>;
>> +	};
>> +
>> +	i2c-mux@70 {
>> +		compatible = "nxp,pca9546";
>> +		reg = <0x70>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		status = "okay";
> Why? Drop
>
>> +		i2c-mux-idle-disconnect;
>> +
>> +		i2c4mux0chn0: i2c@0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0>;
>> +
>> +			eeprom@50 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x50>;
>> +			};
>> +
>> +			pca9551@60 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
>
>> +				compatible = "nxp,pca9551";
>> +				reg = <0x60>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				gpio-controller;
>> +				#gpio-cells = <2>;
>> +
>> +				led@0 {
>> +					label = "cablecard0-cxp-top";
>> +					reg = <0>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +
>> +				led@1 {
>> +					label = "cablecard0-cxp-bot";
>> +					reg = <1>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +			};
>> +		};
>> +
>> +		i2c4mux0chn1: i2c@1 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <1>;
> reg is after compatible, which means if there is no compatible, reg is
> always first. This applies you all your DTS patches. This patchset and
> future.
>
>
>> +
>> +			eeprom@51 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x51>;
>> +			};
>> +		};
>> +
>> +		i2c4mux0chn2: i2c@2 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <2>;
>> +
>> +			eeprom@52 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x52>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&i2c5 {
>> +	status = "okay";
>> +
>> +	tmp275@48 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
>
>> +		compatible = "ti,tmp275";
>> +		reg = <0x48>;
>> +	};
>> +
>> +	tmp275@49 {
>> +		compatible = "ti,tmp275";
>> +		reg = <0x49>;
>> +	};
>> +
>> +	i2c-mux@70 {
>> +		compatible = "nxp,pca9546";
>> +		reg = <0x70>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		status = "okay";
> Drop
>
>
>> +		i2c-mux-idle-disconnect;
>> +
>> +		i2c5mux0chn0: i2c@0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0>;
>> +
>> +			eeprom@50 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x50>;
>> +			};
>> +
>> +			pca9551@60 {
>> +				compatible = "nxp,pca9551";
>> +				reg = <0x60>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				gpio-controller;
>> +				#gpio-cells = <2>;
>> +
>> +				led@0 {
>> +					label = "cablecard3-cxp-top";
>> +					reg = <0>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +
>> +				led@1 {
>> +					label = "cablecard3-cxp-bot";
>> +					reg = <1>;
>> +					retain-state-shutdown;
>> +					default-state = "keep";
>> +					type = <PCA955X_TYPE_LED>;
>> +				};
>> +			};
>> +		};
>> +
>> +		i2c5mux0chn1: i2c@1 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <1>;
>> +
>> +			eeprom@51 {
>> +				compatible = "atmel,24c64";
>> +				reg = <0x51>;
>> +			};
>> +
>> +			pca9551@61 {
>> +				compatible = "nxp,pca9551";
>> +				reg = <0x61>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>
> And here you have correct order of properties...
>
>
>
> Best regards,
> Krzysztof
>

[PATCH v3 14/14] ARM: dts: aspeed: Add IBM P11 Fuji BMC system

[Eddie James]

Add the device tree for the new BMC system. The Fuji is a P11
system with eight processors.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 arch/arm/boot/dts/aspeed/Makefile             |    2 +
 .../boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts   | 3984 +++++++++++++++++
 2 files changed, 3986 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts

diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index 715106b3baa1..783409b7c206 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -33,8 +33,10 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-facebook-yamp.dtb \
 	aspeed-bmc-facebook-yosemitev2.dtb \
 	aspeed-bmc-facebook-yosemite4.dtb \
+	aspeed-bmc-ibm-blueridge.dtb \
 	aspeed-bmc-ibm-bonnell.dtb \
 	aspeed-bmc-ibm-everest.dtb \
+	aspeed-bmc-ibm-fuji.dtb \
 	aspeed-bmc-ibm-rainier.dtb \
 	aspeed-bmc-ibm-rainier-1s4u.dtb \
 	aspeed-bmc-ibm-rainier-4u.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
new file mode 100644
index 000000000000..dc41fa815761
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
@@ -0,0 +1,3984 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Fuji";
+	compatible = "ibm,fuji-bmc", "aspeed,ast2600";
+
+	aliases {
+		i2c500 = &cfam4_i2c0;
+		i2c501 = &cfam4_i2c1;
+		i2c510 = &cfam4_i2c10;
+		i2c511 = &cfam4_i2c11;
+		i2c512 = &cfam4_i2c12;
+		i2c513 = &cfam4_i2c13;
+		i2c514 = &cfam4_i2c14;
+		i2c515 = &cfam4_i2c15;
+		i2c602 = &cfam5_i2c2;
+		i2c603 = &cfam5_i2c3;
+		i2c610 = &cfam5_i2c10;
+		i2c611 = &cfam5_i2c11;
+		i2c614 = &cfam5_i2c14;
+		i2c615 = &cfam5_i2c15;
+		i2c616 = &cfam5_i2c16;
+		i2c617 = &cfam5_i2c17;
+		i2c700 = &cfam6_i2c0;
+		i2c701 = &cfam6_i2c1;
+		i2c710 = &cfam6_i2c10;
+		i2c711 = &cfam6_i2c11;
+		i2c712 = &cfam6_i2c12;
+		i2c713 = &cfam6_i2c13;
+		i2c714 = &cfam6_i2c14;
+		i2c715 = &cfam6_i2c15;
+		i2c802 = &cfam7_i2c2;
+		i2c803 = &cfam7_i2c3;
+		i2c810 = &cfam7_i2c10;
+		i2c811 = &cfam7_i2c11;
+		i2c814 = &cfam7_i2c14;
+		i2c815 = &cfam7_i2c15;
+		i2c816 = &cfam7_i2c16;
+		i2c817 = &cfam7_i2c17;
+
+		i2c16 = &i2c4mux0chn0;
+		i2c17 = &i2c4mux0chn1;
+		i2c18 = &i2c4mux0chn2;
+		i2c19 = &i2c5mux0chn0;
+		i2c20 = &i2c5mux0chn1;
+		i2c21 = &i2c5mux0chn2;
+		i2c22 = &i2c5mux0chn3;
+		i2c23 = &i2c6mux0chn0;
+		i2c24 = &i2c6mux0chn1;
+		i2c25 = &i2c6mux0chn2;
+		i2c26 = &i2c6mux0chn3;
+		i2c27 = &i2c14mux0chn0;
+		i2c28 = &i2c14mux0chn1;
+		i2c29 = &i2c14mux0chn2;
+		i2c30 = &i2c14mux0chn3;
+		i2c31 = &i2c14mux1chn0;
+		i2c32 = &i2c14mux1chn1;
+		i2c33 = &i2c14mux1chn2;
+		i2c34 = &i2c14mux1chn3;
+		i2c35 = &i2c15mux0chn0;
+		i2c36 = &i2c15mux0chn1;
+		i2c37 = &i2c15mux0chn2;
+		i2c38 = &i2c15mux0chn3;
+		i2c39 = &i2c15mux1chn0;
+		i2c40 = &i2c15mux1chn1;
+		i2c41 = &i2c15mux1chn2;
+		i2c42 = &i2c15mux1chn3;
+		i2c43 = &i2c15mux2chn0;
+		i2c44 = &i2c15mux2chn1;
+		i2c45 = &i2c15mux2chn2;
+		i2c46 = &i2c15mux2chn3;
+		i2c47 = &i2c8mux0chn0;
+		i2c48 = &i2c8mux0chn1;
+
+		serial4 = &uart5;
+
+		sbefifo500 = &sbefifo500;
+		sbefifo501 = &sbefifo501;
+		sbefifo510 = &sbefifo510;
+		sbefifo511 = &sbefifo511;
+		sbefifo512 = &sbefifo512;
+		sbefifo513 = &sbefifo513;
+		sbefifo514 = &sbefifo514;
+		sbefifo515 = &sbefifo515;
+		sbefifo602 = &sbefifo602;
+		sbefifo603 = &sbefifo603;
+		sbefifo610 = &sbefifo610;
+		sbefifo611 = &sbefifo611;
+		sbefifo614 = &sbefifo614;
+		sbefifo615 = &sbefifo615;
+		sbefifo616 = &sbefifo616;
+		sbefifo617 = &sbefifo617;
+		sbefifo700 = &sbefifo700;
+		sbefifo701 = &sbefifo701;
+		sbefifo710 = &sbefifo710;
+		sbefifo711 = &sbefifo711;
+		sbefifo712 = &sbefifo712;
+		sbefifo713 = &sbefifo713;
+		sbefifo714 = &sbefifo714;
+		sbefifo715 = &sbefifo715;
+		sbefifo802 = &sbefifo802;
+		sbefifo803 = &sbefifo803;
+		sbefifo810 = &sbefifo810;
+		sbefifo811 = &sbefifo811;
+		sbefifo814 = &sbefifo814;
+		sbefifo815 = &sbefifo815;
+		sbefifo816 = &sbefifo816;
+		sbefifo817 = &sbefifo817;
+
+		scom500 = &scom500;
+		scom501 = &scom501;
+		scom510 = &scom510;
+		scom511 = &scom511;
+		scom512 = &scom512;
+		scom513 = &scom513;
+		scom514 = &scom514;
+		scom515 = &scom515;
+		scom602 = &scom602;
+		scom603 = &scom603;
+		scom610 = &scom610;
+		scom611 = &scom611;
+		scom614 = &scom614;
+		scom615 = &scom615;
+		scom616 = &scom616;
+		scom617 = &scom617;
+		scom700 = &scom700;
+		scom701 = &scom701;
+		scom710 = &scom710;
+		scom711 = &scom711;
+		scom712 = &scom712;
+		scom713 = &scom713;
+		scom714 = &scom714;
+		scom715 = &scom715;
+		scom802 = &scom802;
+		scom803 = &scom803;
+		scom810 = &scom810;
+		scom811 = &scom811;
+		scom814 = &scom814;
+		scom815 = &scom815;
+		scom816 = &scom816;
+		scom817 = &scom817;
+
+		spi50 = &cfam4_spi0;
+		spi51 = &cfam4_spi1;
+		spi52 = &cfam4_spi2;
+		spi53 = &cfam4_spi3;
+		spi60 = &cfam5_spi0;
+		spi61 = &cfam5_spi1;
+		spi62 = &cfam5_spi2;
+		spi63 = &cfam5_spi3;
+		spi70 = &cfam6_spi0;
+		spi71 = &cfam6_spi1;
+		spi72 = &cfam6_spi2;
+		spi73 = &cfam6_spi3;
+		spi80 = &cfam7_spi0;
+		spi81 = &cfam7_spi1;
+		spi82 = &cfam7_spi2;
+		spi83 = &cfam7_spi3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: tcg_event_log@b3d00000 {
+			no-map;
+			reg = <0xb3d00000 0x100000>;
+		};
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>; /* 16M */
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-fan0-presence {
+			label = "fan0-presence";
+			gpios = <&pca0 15 GPIO_ACTIVE_LOW>;
+			linux,code = <15>;
+		};
+
+		event-fan1-presence {
+			label = "fan1-presence";
+			gpios = <&pca0 14 GPIO_ACTIVE_LOW>;
+			linux,code = <14>;
+		};
+
+		event-fan2-presence {
+			label = "fan2-presence";
+			gpios = <&pca0 13 GPIO_ACTIVE_LOW>;
+			linux,code = <13>;
+		};
+
+		event-fan3-presence {
+			label = "fan3-presence";
+			gpios = <&pca0 12 GPIO_ACTIVE_LOW>;
+			linux,code = <12>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* RTC battery fault LED at the back */
+		led-rtc-battery {
+			gpios = <&gpio0 ASPEED_GPIO(H, 0) GPIO_ACTIVE_LOW>;
+		};
+
+		/* BMC Card fault LED at the back */
+		led-bmc {
+			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure Identify LED at the back */
+		led-rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure fault LED at the back */
+		led-rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		/* PCIE slot power LED */
+		led-pcieslot-power {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+				 &pinctrl_adc10_default &pinctrl_adc11_default
+				 &pinctrl_adc12_default &pinctrl_adc13_default
+				 &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"USERSPACE_RSTIND_BUFF","","","","","","checkstop","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"led-rtc-battery","led-bmc","led-rear-enc-id0","led-rear-enc-fault0","","","","",
+	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","usb-power","","","","",
+	/*P0-P7*/	"","","","","led-pcieslot-power","","","",
+	/*Q0-Q7*/	"","","regulator-standby-faulted","","","","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","I2C_FLASH_MICRO_N","","",
+	/*S0-S7*/	"","","","","power-ffs-sync-history","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","BMC_3RESTART_ATTEMPT_P","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/   "","","","","","","","";
+
+	usb_power-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	pca1: pca9552@62 {
+		compatible = "nxp,pca9552";
+		reg = <0x62>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-ps0",
+			"presence-ps1",
+			"presence-ps2",
+			"presence-ps3",
+			"presence-pdb",
+			"presence-tpm",
+			"", "",
+			"presence-cp0",
+			"presence-cp1",
+			"presence-cp2",
+			"presence-cp3",
+			"presence-dasd",
+			"presence-lcd-op",
+			"presence-base-op",
+			"";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	eeprom@54 {
+		compatible = "atmel,24c128";
+		reg = <0x54>;
+	};
+
+	power-supply@68 {
+		compatible = "ibm,cffps";
+		reg = <0x68>;
+	};
+
+	power-supply@69 {
+		compatible = "ibm,cffps";
+		reg = <0x69>;
+	};
+
+	power-supply@6b {
+		compatible = "ibm,cffps";
+		reg = <0x6b>;
+	};
+
+	power-supply@6d {
+		compatible = "ibm,cffps";
+		reg = <0x6d>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	pca2: pca9552@65 {
+		compatible = "nxp,pca9552";
+		reg = <0x65>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-cable-card1",
+			"presence-cable-card2",
+			"presence-cable-card3",
+			"presence-cable-card4",
+			"presence-cable-card5",
+			"expander-cable-card1",
+			"expander-cable-card2",
+			"expander-cable-card3",
+			"expander-cable-card4",
+			"expander-cable-card5";
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			pca_cable_card_c01: pca9551@62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c01-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c01-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca_cable_card_c02: pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c02-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c02-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca_cable_card_c03: pca9551@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c03-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c03-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	pca3: pca9552@66 {
+		compatible = "nxp,pca9552";
+		reg = <0x66>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-cable-card6",
+			"presence-cable-card7",
+			"presence-cable-card8",
+			"presence-cable-card9",
+			"presence-cable-card10",
+			"presence-cable-card11",
+			"expander-cable-card6",
+			"expander-cable-card7",
+			"expander-cable-card8",
+			"expander-cable-card9",
+			"expander-cable-card10",
+			"expander-cable-card11";
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca_cable_card_c04: pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c04-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c04-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca_cable_card_c05: pca9551@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c05-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c05-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			pca_cable_card_c06: pca9551@62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c06-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c06-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+
+			pca_cable_card_c07: pca9551@63 {
+				compatible = "nxp,pca9551";
+				reg = <0x63>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c07-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c07-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c6mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@50 {
+			compatible = "atmel,24c64";
+			reg = <0x50>;
+			};
+
+			pca_cable_card_c08: pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c08-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c08-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			pca_cable_card_c09: pca9551@62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c09-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c09-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+
+			pca_cable_card_c10: pca9551@63 {
+				compatible = "nxp,pca9551";
+				reg = <0x63>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c10-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c10-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca_cable_card_c11: pca9551@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c11-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c11-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+
+	pca_pcie_slot: pca9552@65 {
+		compatible = "nxp,pca9552";
+		reg = <0x65>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@1 {
+			label = "pcieslot-c01";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "pcieslot-c02";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "pcieslot-c03";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "pcieslot-c04";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "pcieslot-c05";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "pcieslot-c06";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "pcieslot-c07";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "pcieslot-c08";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "pcieslot-c09";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "pcieslot-c10";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "pcieslot-c11";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	pic0_dimm: pca9552@31 {
+		compatible = "ibm,pca9552";
+		reg = <0x31>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm6";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm7";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm8";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm9";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm10";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm11";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm12";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm13";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm14";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm15";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic1_dimm: pca9552@32 {
+		compatible = "ibm,pca9552";
+		reg = <0x32>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm16";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm17";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm18";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm19";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm20";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm21";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm22";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm23";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm24";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm25";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm26";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm27";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm28";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm29";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm30";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm31";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic2_dimm: pca9552@33 {
+		compatible = "ibm,pca9552";
+		reg = <0x33>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm32";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm33";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm34";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm35";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm36";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm37";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm38";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm39";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm40";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm41";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm42";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm43";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm44";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm45";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm46";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm47";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic3_dimm: pca9552@30 {
+		compatible = "ibm,pca9552";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm48";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm49";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm50";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm51";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm52";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm53";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm54";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm55";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm56";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm57";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm58";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm59";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm60";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm61";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm62";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm63";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic0_vrm_misc: pca9552@34 {
+		compatible = "ibm,pca9552";
+		reg = <0x34>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "planar";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "tpm";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "cpu3-c61";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "cpu0-c14";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "opencapi-connector3";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "opencapi-connector4";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "opencapi-connector5";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "vrm4";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "vrm5";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "vrm6";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "vrm7";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "vrm12";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "vrm13";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "vrm14";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "vrm15";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic1_vrm_misc: pca9552@35 {
+		compatible = "ibm,pca9552";
+		reg = <0x35>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "dasd-backplane";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "power-distribution";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "cpu1-c19";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "cpu2-c56";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "opencapi-connector0";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "opencapi-connector1";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "opencapi-connector2";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "vrm0";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "vrm1";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "vrm2";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "vrm3";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "vrm8";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "vrm9";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "vrm10";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "vrm11";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	ucd90320@11 {
+		compatible = "ti,ucd90320";
+		reg = <0x11>;
+	};
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c8mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c8mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm@2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c14 {
+	multi-master;
+	status = "okay";
+
+	ibm-panel@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		idle-state = <1>;
+
+		i2c14mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@51 {
+				compatible = "atmel,24c32";
+				reg = <0x51>;
+			};
+		};
+
+		i2c14mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+
+			pca_oppanel: pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "front-sys-id0";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "front-check-log0";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@2 {
+					label = "front-enc-fault1";
+					reg = <2>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@3 {
+					label = "front-sys-pwron0";
+					reg = <3>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c14mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			max31785@52 {
+				compatible = "maxim,max31785a";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x52>;
+			};
+
+			pca_fan_nvme: pca9552@60 {
+				compatible = "nxp,pca9552";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "nvme0";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "nvme1";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@2 {
+					label = "nvme2";
+					reg = <2>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@3 {
+					label = "nvme3";
+					reg = <3>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@4 {
+					label = "nvme4";
+					reg = <4>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@5 {
+					label = "nvme5";
+					reg = <5>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@6 {
+					label = "nvme6";
+					reg = <6>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@7 {
+					label = "nvme7";
+					reg = <7>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@8 {
+					label = "nvme8";
+					reg = <8>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@9 {
+					label = "nvme9";
+					reg = <9>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@10 {
+					label = "fan0";
+					reg = <10>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@11 {
+					label = "fan1";
+					reg = <11>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@12 {
+					label = "fan2";
+					reg = <12>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@13 {
+					label = "fan3";
+					reg = <13>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+
+			pca0: pca9552@61 {
+				compatible = "nxp,pca9552";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x61>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				gpio-line-names =
+					"","","","",
+					"","","","",
+					"","","","",
+					"presence-fan3",
+					"presence-fan2",
+					"presence-fan1",
+					"presence-fan0";
+			};
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c14mux1chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux1chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux2chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux2chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux2chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c15mux2chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <210>, <228>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&xdma {
+	status = "okay";
+	memory-region = <&vga_memory>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+#include "ibm-power11-quad.dtsi"
+
+&fsi_hub0 {
+	cfam@4,0 { /* DCM2_C0 */
+		reg = <4 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <4>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam4_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom500: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo500: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom501: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo501: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom510: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo510: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom511: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo511: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom512: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo512: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom513: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo513: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom514: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo514: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom515: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo515: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam4_spi0: spi@0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam4_spi1: spi@20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam4_spi2: spi@40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam4_spi3: spi@60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ4: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub4: hub@3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@5,0 { /* DCM2_C1 */
+		reg = <5 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <5>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam5_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom602: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo602: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom603: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo603: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom610: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo610: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom611: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo611: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom614: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo614: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom615: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo615: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom616: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo616: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom617: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo617: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam5_spi0: spi@0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam5_spi1: spi@20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam5_spi2: spi@40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam5_spi3: spi@60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ5: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub5: hub@3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@6,0 { /* DCM3_C0 */
+		reg = <6 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <6>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam6_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom700: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo700: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom701: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo701: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom710: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo710: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom711: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo711: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom712: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo712: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom713: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo713: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom714: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo714: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom715: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo715: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam6_spi0: spi@0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam6_spi1: spi@20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam6_spi2: spi@40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam6_spi3: spi@60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ6: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub6: hub@3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@7,0 { /* DCM3_C1 */
+		reg = <7 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <7>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam7_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom802: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo802: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom803: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo803: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom810: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo810: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom811: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo811: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom814: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo814: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom815: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo815: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom816: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo816: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+
+				fsi-i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom817: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo817: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam7_spi0: spi@0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam7_spi1: spi@20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam7_spi2: spi@40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam7_spi3: spi@60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ7: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub7: hub@3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ4 {
+	reg = <5>;
+};
+
+&fsi_occ5 {
+	reg = <6>;
+};
+
+&fsi_occ6 {
+	reg = <7>;
+};
+
+&fsi_occ7 {
+	reg = <8>;
+};
-- 
2.39.3

[PATCH v3 14/14] ARM: dts: aspeed: Add IBM P11 Fuji BMC system

[Eddie James]

Add the device tree for the new BMC system. The Fuji is a P11
system with eight processors.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 arch/arm/boot/dts/aspeed/Makefile             |    2 +
 .../boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts   | 3984 +++++++++++++++++
 2 files changed, 3986 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts

diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index 715106b3baa1..783409b7c206 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -33,8 +33,10 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-facebook-yamp.dtb \
 	aspeed-bmc-facebook-yosemitev2.dtb \
 	aspeed-bmc-facebook-yosemite4.dtb \
+	aspeed-bmc-ibm-blueridge.dtb \
 	aspeed-bmc-ibm-bonnell.dtb \
 	aspeed-bmc-ibm-everest.dtb \
+	aspeed-bmc-ibm-fuji.dtb \
 	aspeed-bmc-ibm-rainier.dtb \
 	aspeed-bmc-ibm-rainier-1s4u.dtb \
 	aspeed-bmc-ibm-rainier-4u.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
new file mode 100644
index 000000000000..dc41fa815761
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
@@ -0,0 +1,3984 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Fuji";
+	compatible = "ibm,fuji-bmc", "aspeed,ast2600";
+
+	aliases {
+		i2c500 = &cfam4_i2c0;
+		i2c501 = &cfam4_i2c1;
+		i2c510 = &cfam4_i2c10;
+		i2c511 = &cfam4_i2c11;
+		i2c512 = &cfam4_i2c12;
+		i2c513 = &cfam4_i2c13;
+		i2c514 = &cfam4_i2c14;
+		i2c515 = &cfam4_i2c15;
+		i2c602 = &cfam5_i2c2;
+		i2c603 = &cfam5_i2c3;
+		i2c610 = &cfam5_i2c10;
+		i2c611 = &cfam5_i2c11;
+		i2c614 = &cfam5_i2c14;
+		i2c615 = &cfam5_i2c15;
+		i2c616 = &cfam5_i2c16;
+		i2c617 = &cfam5_i2c17;
+		i2c700 = &cfam6_i2c0;
+		i2c701 = &cfam6_i2c1;
+		i2c710 = &cfam6_i2c10;
+		i2c711 = &cfam6_i2c11;
+		i2c712 = &cfam6_i2c12;
+		i2c713 = &cfam6_i2c13;
+		i2c714 = &cfam6_i2c14;
+		i2c715 = &cfam6_i2c15;
+		i2c802 = &cfam7_i2c2;
+		i2c803 = &cfam7_i2c3;
+		i2c810 = &cfam7_i2c10;
+		i2c811 = &cfam7_i2c11;
+		i2c814 = &cfam7_i2c14;
+		i2c815 = &cfam7_i2c15;
+		i2c816 = &cfam7_i2c16;
+		i2c817 = &cfam7_i2c17;
+
+		i2c16 = &i2c4mux0chn0;
+		i2c17 = &i2c4mux0chn1;
+		i2c18 = &i2c4mux0chn2;
+		i2c19 = &i2c5mux0chn0;
+		i2c20 = &i2c5mux0chn1;
+		i2c21 = &i2c5mux0chn2;
+		i2c22 = &i2c5mux0chn3;
+		i2c23 = &i2c6mux0chn0;
+		i2c24 = &i2c6mux0chn1;
+		i2c25 = &i2c6mux0chn2;
+		i2c26 = &i2c6mux0chn3;
+		i2c27 = &i2c14mux0chn0;
+		i2c28 = &i2c14mux0chn1;
+		i2c29 = &i2c14mux0chn2;
+		i2c30 = &i2c14mux0chn3;
+		i2c31 = &i2c14mux1chn0;
+		i2c32 = &i2c14mux1chn1;
+		i2c33 = &i2c14mux1chn2;
+		i2c34 = &i2c14mux1chn3;
+		i2c35 = &i2c15mux0chn0;
+		i2c36 = &i2c15mux0chn1;
+		i2c37 = &i2c15mux0chn2;
+		i2c38 = &i2c15mux0chn3;
+		i2c39 = &i2c15mux1chn0;
+		i2c40 = &i2c15mux1chn1;
+		i2c41 = &i2c15mux1chn2;
+		i2c42 = &i2c15mux1chn3;
+		i2c43 = &i2c15mux2chn0;
+		i2c44 = &i2c15mux2chn1;
+		i2c45 = &i2c15mux2chn2;
+		i2c46 = &i2c15mux2chn3;
+		i2c47 = &i2c8mux0chn0;
+		i2c48 = &i2c8mux0chn1;
+
+		serial4 = &uart5;
+
+		sbefifo500 = &sbefifo500;
+		sbefifo501 = &sbefifo501;
+		sbefifo510 = &sbefifo510;
+		sbefifo511 = &sbefifo511;
+		sbefifo512 = &sbefifo512;
+		sbefifo513 = &sbefifo513;
+		sbefifo514 = &sbefifo514;
+		sbefifo515 = &sbefifo515;
+		sbefifo602 = &sbefifo602;
+		sbefifo603 = &sbefifo603;
+		sbefifo610 = &sbefifo610;
+		sbefifo611 = &sbefifo611;
+		sbefifo614 = &sbefifo614;
+		sbefifo615 = &sbefifo615;
+		sbefifo616 = &sbefifo616;
+		sbefifo617 = &sbefifo617;
+		sbefifo700 = &sbefifo700;
+		sbefifo701 = &sbefifo701;
+		sbefifo710 = &sbefifo710;
+		sbefifo711 = &sbefifo711;
+		sbefifo712 = &sbefifo712;
+		sbefifo713 = &sbefifo713;
+		sbefifo714 = &sbefifo714;
+		sbefifo715 = &sbefifo715;
+		sbefifo802 = &sbefifo802;
+		sbefifo803 = &sbefifo803;
+		sbefifo810 = &sbefifo810;
+		sbefifo811 = &sbefifo811;
+		sbefifo814 = &sbefifo814;
+		sbefifo815 = &sbefifo815;
+		sbefifo816 = &sbefifo816;
+		sbefifo817 = &sbefifo817;
+
+		scom500 = &scom500;
+		scom501 = &scom501;
+		scom510 = &scom510;
+		scom511 = &scom511;
+		scom512 = &scom512;
+		scom513 = &scom513;
+		scom514 = &scom514;
+		scom515 = &scom515;
+		scom602 = &scom602;
+		scom603 = &scom603;
+		scom610 = &scom610;
+		scom611 = &scom611;
+		scom614 = &scom614;
+		scom615 = &scom615;
+		scom616 = &scom616;
+		scom617 = &scom617;
+		scom700 = &scom700;
+		scom701 = &scom701;
+		scom710 = &scom710;
+		scom711 = &scom711;
+		scom712 = &scom712;
+		scom713 = &scom713;
+		scom714 = &scom714;
+		scom715 = &scom715;
+		scom802 = &scom802;
+		scom803 = &scom803;
+		scom810 = &scom810;
+		scom811 = &scom811;
+		scom814 = &scom814;
+		scom815 = &scom815;
+		scom816 = &scom816;
+		scom817 = &scom817;
+
+		spi50 = &cfam4_spi0;
+		spi51 = &cfam4_spi1;
+		spi52 = &cfam4_spi2;
+		spi53 = &cfam4_spi3;
+		spi60 = &cfam5_spi0;
+		spi61 = &cfam5_spi1;
+		spi62 = &cfam5_spi2;
+		spi63 = &cfam5_spi3;
+		spi70 = &cfam6_spi0;
+		spi71 = &cfam6_spi1;
+		spi72 = &cfam6_spi2;
+		spi73 = &cfam6_spi3;
+		spi80 = &cfam7_spi0;
+		spi81 = &cfam7_spi1;
+		spi82 = &cfam7_spi2;
+		spi83 = &cfam7_spi3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory at 80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: tcg_event_log at b3d00000 {
+			no-map;
+			reg = <0xb3d00000 0x100000>;
+		};
+
+		ramoops at b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region at b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region at bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>; /* 16M */
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-fan0-presence {
+			label = "fan0-presence";
+			gpios = <&pca0 15 GPIO_ACTIVE_LOW>;
+			linux,code = <15>;
+		};
+
+		event-fan1-presence {
+			label = "fan1-presence";
+			gpios = <&pca0 14 GPIO_ACTIVE_LOW>;
+			linux,code = <14>;
+		};
+
+		event-fan2-presence {
+			label = "fan2-presence";
+			gpios = <&pca0 13 GPIO_ACTIVE_LOW>;
+			linux,code = <13>;
+		};
+
+		event-fan3-presence {
+			label = "fan3-presence";
+			gpios = <&pca0 12 GPIO_ACTIVE_LOW>;
+			linux,code = <12>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* RTC battery fault LED at the back */
+		led-rtc-battery {
+			gpios = <&gpio0 ASPEED_GPIO(H, 0) GPIO_ACTIVE_LOW>;
+		};
+
+		/* BMC Card fault LED at the back */
+		led-bmc {
+			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure Identify LED at the back */
+		led-rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure fault LED at the back */
+		led-rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		/* PCIE slot power LED */
+		led-pcieslot-power {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+				 &pinctrl_adc10_default &pinctrl_adc11_default
+				 &pinctrl_adc12_default &pinctrl_adc13_default
+				 &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"USERSPACE_RSTIND_BUFF","","","","","","checkstop","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"led-rtc-battery","led-bmc","led-rear-enc-id0","led-rear-enc-fault0","","","","",
+	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","usb-power","","","","",
+	/*P0-P7*/	"","","","","led-pcieslot-power","","","",
+	/*Q0-Q7*/	"","","regulator-standby-faulted","","","","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","I2C_FLASH_MICRO_N","","",
+	/*S0-S7*/	"","","","","power-ffs-sync-history","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","BMC_3RESTART_ATTEMPT_P","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/   "","","","","","","","";
+
+	usb_power-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom at 51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	pca1: pca9552 at 62 {
+		compatible = "nxp,pca9552";
+		reg = <0x62>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-ps0",
+			"presence-ps1",
+			"presence-ps2",
+			"presence-ps3",
+			"presence-pdb",
+			"presence-tpm",
+			"", "",
+			"presence-cp0",
+			"presence-cp1",
+			"presence-cp2",
+			"presence-cp3",
+			"presence-dasd",
+			"presence-lcd-op",
+			"presence-base-op",
+			"";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	eeprom at 54 {
+		compatible = "atmel,24c128";
+		reg = <0x54>;
+	};
+
+	power-supply at 68 {
+		compatible = "ibm,cffps";
+		reg = <0x68>;
+	};
+
+	power-supply at 69 {
+		compatible = "ibm,cffps";
+		reg = <0x69>;
+	};
+
+	power-supply at 6b {
+		compatible = "ibm,cffps";
+		reg = <0x6b>;
+	};
+
+	power-supply at 6d {
+		compatible = "ibm,cffps";
+		reg = <0x6d>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	pca2: pca9552 at 65 {
+		compatible = "nxp,pca9552";
+		reg = <0x65>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-cable-card1",
+			"presence-cable-card2",
+			"presence-cable-card3",
+			"presence-cable-card4",
+			"presence-cable-card5",
+			"expander-cable-card1",
+			"expander-cable-card2",
+			"expander-cable-card3",
+			"expander-cable-card4",
+			"expander-cable-card5";
+	};
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom at 52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			pca_cable_card_c01: pca9551 at 62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c01-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c01-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca_cable_card_c02: pca9551 at 60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c02-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c02-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom at 51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca_cable_card_c03: pca9551 at 61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c03-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c03-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	pca3: pca9552 at 66 {
+		compatible = "nxp,pca9552";
+		reg = <0x66>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-cable-card6",
+			"presence-cable-card7",
+			"presence-cable-card8",
+			"presence-cable-card9",
+			"presence-cable-card10",
+			"presence-cable-card11",
+			"expander-cable-card6",
+			"expander-cable-card7",
+			"expander-cable-card8",
+			"expander-cable-card9",
+			"expander-cable-card10",
+			"expander-cable-card11";
+	};
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca_cable_card_c04: pca9551 at 60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c04-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c04-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom at 51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca_cable_card_c05: pca9551 at 61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c05-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c05-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom at 52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			pca_cable_card_c06: pca9551 at 62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c06-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c06-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn3: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+
+			pca_cable_card_c07: pca9551 at 63 {
+				compatible = "nxp,pca9551";
+				reg = <0x63>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c07-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c07-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c6mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom at 50 {
+			compatible = "atmel,24c64";
+			reg = <0x50>;
+			};
+
+			pca_cable_card_c08: pca9551 at 60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c08-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c08-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom at 52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			pca_cable_card_c09: pca9551 at 62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c09-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c09-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+
+			pca_cable_card_c10: pca9551 at 63 {
+				compatible = "nxp,pca9551";
+				reg = <0x63>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c10-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c10-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn3: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom at 51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca_cable_card_c11: pca9551 at 61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "cablecard-c11-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "cablecard-c11-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+
+	pca_pcie_slot: pca9552 at 65 {
+		compatible = "nxp,pca9552";
+		reg = <0x65>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 1 {
+			label = "pcieslot-c01";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "pcieslot-c02";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "pcieslot-c03";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "pcieslot-c04";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "pcieslot-c05";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "pcieslot-c06";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "pcieslot-c07";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "pcieslot-c08";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "pcieslot-c09";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "pcieslot-c10";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "pcieslot-c11";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	pic0_dimm: pca9552 at 31 {
+		compatible = "ibm,pca9552";
+		reg = <0x31>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "ddimm0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "ddimm1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "ddimm2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "ddimm3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "ddimm4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "ddimm5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "ddimm6";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "ddimm7";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "ddimm8";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "ddimm9";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "ddimm10";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "ddimm11";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 12 {
+			label = "ddimm12";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 13 {
+			label = "ddimm13";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 14 {
+			label = "ddimm14";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 15 {
+			label = "ddimm15";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic1_dimm: pca9552 at 32 {
+		compatible = "ibm,pca9552";
+		reg = <0x32>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "ddimm16";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "ddimm17";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "ddimm18";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "ddimm19";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "ddimm20";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "ddimm21";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "ddimm22";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "ddimm23";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "ddimm24";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "ddimm25";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "ddimm26";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "ddimm27";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 12 {
+			label = "ddimm28";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 13 {
+			label = "ddimm29";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 14 {
+			label = "ddimm30";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 15 {
+			label = "ddimm31";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic2_dimm: pca9552 at 33 {
+		compatible = "ibm,pca9552";
+		reg = <0x33>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "ddimm32";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "ddimm33";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "ddimm34";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "ddimm35";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "ddimm36";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "ddimm37";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "ddimm38";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "ddimm39";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "ddimm40";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "ddimm41";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "ddimm42";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "ddimm43";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 12 {
+			label = "ddimm44";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 13 {
+			label = "ddimm45";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 14 {
+			label = "ddimm46";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 15 {
+			label = "ddimm47";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic3_dimm: pca9552 at 30 {
+		compatible = "ibm,pca9552";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "ddimm48";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "ddimm49";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "ddimm50";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "ddimm51";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "ddimm52";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "ddimm53";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "ddimm54";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 7 {
+			label = "ddimm55";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "ddimm56";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "ddimm57";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "ddimm58";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "ddimm59";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 12 {
+			label = "ddimm60";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 13 {
+			label = "ddimm61";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 14 {
+			label = "ddimm62";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 15 {
+			label = "ddimm63";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic0_vrm_misc: pca9552 at 34 {
+		compatible = "ibm,pca9552";
+		reg = <0x34>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "planar";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "tpm";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "cpu3-c61";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "cpu0-c14";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "opencapi-connector3";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "opencapi-connector4";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "opencapi-connector5";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "vrm4";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "vrm5";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "vrm6";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "vrm7";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 12 {
+			label = "vrm12";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 13 {
+			label = "vrm13";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 14 {
+			label = "vrm14";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 15 {
+			label = "vrm15";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic1_vrm_misc: pca9552 at 35 {
+		compatible = "ibm,pca9552";
+		reg = <0x35>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led at 0 {
+			label = "dasd-backplane";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 1 {
+			label = "power-distribution";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 2 {
+			label = "cpu1-c19";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 3 {
+			label = "cpu2-c56";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 4 {
+			label = "opencapi-connector0";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 5 {
+			label = "opencapi-connector1";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 6 {
+			label = "opencapi-connector2";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 8 {
+			label = "vrm0";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 9 {
+			label = "vrm1";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 10 {
+			label = "vrm2";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 11 {
+			label = "vrm3";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 12 {
+			label = "vrm8";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 13 {
+			label = "vrm9";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 14 {
+			label = "vrm10";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led at 15 {
+			label = "vrm11";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	ucd90320 at 11 {
+		compatible = "ti,ucd90320";
+		reg = <0x11>;
+	};
+
+	rtc at 32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	eeprom at 51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c8mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c8mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	eeprom at 50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom at 51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom at 53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom at 52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	eeprom at 51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom at 53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom at 52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	eeprom at 51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom at 53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom at 52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm at 2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom at 51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom at 53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom at 52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c14 {
+	multi-master;
+	status = "okay";
+
+	ibm-panel at 62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		idle-state = <1>;
+
+		i2c14mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom at 50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom at 51 {
+				compatible = "atmel,24c32";
+				reg = <0x51>;
+			};
+		};
+
+		i2c14mux0chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom at 50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+
+			pca_oppanel: pca9551 at 60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "front-sys-id0";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "front-check-log0";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 2 {
+					label = "front-enc-fault1";
+					reg = <2>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 3 {
+					label = "front-sys-pwron0";
+					reg = <3>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c14mux0chn3: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			max31785 at 52 {
+				compatible = "maxim,max31785a";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x52>;
+			};
+
+			pca_fan_nvme: pca9552 at 60 {
+				compatible = "nxp,pca9552";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led at 0 {
+					label = "nvme0";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 1 {
+					label = "nvme1";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 2 {
+					label = "nvme2";
+					reg = <2>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 3 {
+					label = "nvme3";
+					reg = <3>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 4 {
+					label = "nvme4";
+					reg = <4>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 5 {
+					label = "nvme5";
+					reg = <5>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 6 {
+					label = "nvme6";
+					reg = <6>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 7 {
+					label = "nvme7";
+					reg = <7>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 8 {
+					label = "nvme8";
+					reg = <8>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 9 {
+					label = "nvme9";
+					reg = <9>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 10 {
+					label = "fan0";
+					reg = <10>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 11 {
+					label = "fan1";
+					reg = <11>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 12 {
+					label = "fan2";
+					reg = <12>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led at 13 {
+					label = "fan3";
+					reg = <13>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+
+			pca0: pca9552 at 61 {
+				compatible = "nxp,pca9552";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x61>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				gpio-line-names =
+					"","","","",
+					"","","","",
+					"","","","",
+					"presence-fan3",
+					"presence-fan2",
+					"presence-fan1",
+					"presence-fan0";
+			};
+		};
+	};
+
+	i2c-mux at 71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c14mux1chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom at 50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom at 50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom at 50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn3: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom at 50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	i2c-mux at 70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux0chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn3: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+	};
+
+	i2c-mux at 71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux1chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn3: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+	};
+
+	i2c-mux at 72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux2chn0: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux2chn1: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom at 53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux2chn2: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c15mux2chn3: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <210>, <228>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&xdma {
+	status = "okay";
+	memory-region = <&vga_memory>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+#include "ibm-power11-quad.dtsi"
+
+&fsi_hub0 {
+	cfam at 4,0 { /* DCM2_C0 */
+		reg = <4 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <4>;
+
+		scom at 1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c at 1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam4_i2c0: i2c-bus at 0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom500: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo500: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c1: i2c-bus at 1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom501: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo501: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c10: i2c-bus at a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom510: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo510: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c11: i2c-bus at b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom511: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo511: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c12: i2c-bus at c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom512: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo512: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c13: i2c-bus at d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom513: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo513: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c14: i2c-bus at e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom514: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo514: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c15: i2c-bus at f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom515: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo515: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi at 1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam4_spi0: spi at 0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam4_spi1: spi at 20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam4_spi2: spi at 40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam4_spi3: spi at 60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo at 2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ4: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub4: hub at 3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam at 5,0 { /* DCM2_C1 */
+		reg = <5 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <5>;
+
+		scom at 1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c at 1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam5_i2c2: i2c-bus at 2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom602: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo602: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c3: i2c-bus at 3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom603: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo603: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c10: i2c-bus at a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom610: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo610: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c11: i2c-bus at b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom611: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo611: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c14: i2c-bus at e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom614: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo614: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c15: i2c-bus at f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom615: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo615: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c16: i2c-bus at 10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom616: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo616: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c17: i2c-bus at 11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom617: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo617: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi at 1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam5_spi0: spi at 0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam5_spi1: spi at 20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam5_spi2: spi at 40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam5_spi3: spi at 60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo at 2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ5: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub5: hub at 3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam at 6,0 { /* DCM3_C0 */
+		reg = <6 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <6>;
+
+		scom at 1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c at 1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam6_i2c0: i2c-bus at 0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom700: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo700: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c1: i2c-bus at 1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom701: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo701: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c10: i2c-bus at a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom710: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo710: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c11: i2c-bus at b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom711: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo711: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c12: i2c-bus at c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom712: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo712: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c13: i2c-bus at d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom713: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo713: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c14: i2c-bus at e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom714: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo714: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c15: i2c-bus at f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom715: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo715: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi at 1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam6_spi0: spi at 0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam6_spi1: spi at 20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam6_spi2: spi at 40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam6_spi3: spi at 60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo at 2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ6: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub6: hub at 3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam at 7,0 { /* DCM3_C1 */
+		reg = <7 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <7>;
+
+		scom at 1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c at 1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam7_i2c2: i2c-bus at 2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom802: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo802: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c3: i2c-bus at 3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom803: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo803: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c10: i2c-bus at a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom810: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo810: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c11: i2c-bus at b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom811: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo811: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c14: i2c-bus at e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom814: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo814: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c15: i2c-bus at f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom815: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo815: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c16: i2c-bus at 10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom816: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo816: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c17: i2c-bus at 11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+
+				fsi-i2cr at 20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam at 0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom817: scom at 1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo817: sbefifo at 2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi at 1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam7_spi0: spi at 0 {
+				compatible = "ibm,p10-spi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam7_spi1: spi at 20 {
+				compatible = "ibm,p10-spi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam7_spi2: spi at 40 {
+				compatible = "ibm,p10-spi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam7_spi3: spi at 60 {
+				compatible = "ibm,p10-spi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom at 0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					size = <0x80000>;
+					address-width = <24>;
+					pagesize = <256>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo at 2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ7: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub7: hub at 3400 {
+			compatible = "ibm,hub-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ4 {
+	reg = <5>;
+};
+
+&fsi_occ5 {
+	reg = <6>;
+};
+
+&fsi_occ6 {
+	reg = <7>;
+};
+
+&fsi_occ7 {
+	reg = <8>;
+};
-- 
2.39.3

[PATCH v3 14/14] ARM: dts: aspeed: Add IBM P11 Fuji BMC system

[Krzysztof Kozlowski]

On 25/04/2024 23:37, Eddie James wrote:
> Add the device tree for the new BMC system. The Fuji is a P11
> system with eight processors.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  arch/arm/boot/dts/aspeed/Makefile             |    2 +
>  .../boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts   | 3984 +++++++++++++++++
>  2 files changed, 3986 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
> 
> diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
> index 715106b3baa1..783409b7c206 100644
> --- a/arch/arm/boot/dts/aspeed/Makefile
> +++ b/arch/arm/boot/dts/aspeed/Makefile
> @@ -33,8 +33,10 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>  	aspeed-bmc-facebook-yamp.dtb \
>  	aspeed-bmc-facebook-yosemitev2.dtb \
>  	aspeed-bmc-facebook-yosemite4.dtb \
> +	aspeed-bmc-ibm-blueridge.dtb \
>  	aspeed-bmc-ibm-bonnell.dtb \
>  	aspeed-bmc-ibm-everest.dtb \
> +	aspeed-bmc-ibm-fuji.dtb \
>  	aspeed-bmc-ibm-rainier.dtb \
>  	aspeed-bmc-ibm-rainier-1s4u.dtb \
>  	aspeed-bmc-ibm-rainier-4u.dtb \
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
> new file mode 100644
> index 000000000000..dc41fa815761
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
> @@ -0,0 +1,3984 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2024 IBM Corp.
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/i2c/i2c.h>
> +#include <dt-bindings/leds/leds-pca955x.h>
> +
> +/ {
> +	model = "Fuji";
> +	compatible = "ibm,fuji-bmc", "aspeed,ast2600";
> +
> +	aliases {
> +		i2c500 = &cfam4_i2c0;
> +		i2c501 = &cfam4_i2c1;
> +		i2c510 = &cfam4_i2c10;
> +		i2c511 = &cfam4_i2c11;
> +		i2c512 = &cfam4_i2c12;
> +		i2c513 = &cfam4_i2c13;
> +		i2c514 = &cfam4_i2c14;
> +		i2c515 = &cfam4_i2c15;
> +		i2c602 = &cfam5_i2c2;
> +		i2c603 = &cfam5_i2c3;
> +		i2c610 = &cfam5_i2c10;
> +		i2c611 = &cfam5_i2c11;
> +		i2c614 = &cfam5_i2c14;
> +		i2c615 = &cfam5_i2c15;
> +		i2c616 = &cfam5_i2c16;
> +		i2c617 = &cfam5_i2c17;
> +		i2c700 = &cfam6_i2c0;
> +		i2c701 = &cfam6_i2c1;
> +		i2c710 = &cfam6_i2c10;
> +		i2c711 = &cfam6_i2c11;
> +		i2c712 = &cfam6_i2c12;
> +		i2c713 = &cfam6_i2c13;
> +		i2c714 = &cfam6_i2c14;
> +		i2c715 = &cfam6_i2c15;
> +		i2c802 = &cfam7_i2c2;
> +		i2c803 = &cfam7_i2c3;
> +		i2c810 = &cfam7_i2c10;
> +		i2c811 = &cfam7_i2c11;
> +		i2c814 = &cfam7_i2c14;
> +		i2c815 = &cfam7_i2c15;
> +		i2c816 = &cfam7_i2c16;
> +		i2c817 = &cfam7_i2c17;
> +
> +		i2c16 = &i2c4mux0chn0;
> +		i2c17 = &i2c4mux0chn1;
> +		i2c18 = &i2c4mux0chn2;
> +		i2c19 = &i2c5mux0chn0;
> +		i2c20 = &i2c5mux0chn1;
> +		i2c21 = &i2c5mux0chn2;
> +		i2c22 = &i2c5mux0chn3;
> +		i2c23 = &i2c6mux0chn0;
> +		i2c24 = &i2c6mux0chn1;
> +		i2c25 = &i2c6mux0chn2;
> +		i2c26 = &i2c6mux0chn3;
> +		i2c27 = &i2c14mux0chn0;
> +		i2c28 = &i2c14mux0chn1;
> +		i2c29 = &i2c14mux0chn2;
> +		i2c30 = &i2c14mux0chn3;
> +		i2c31 = &i2c14mux1chn0;
> +		i2c32 = &i2c14mux1chn1;
> +		i2c33 = &i2c14mux1chn2;
> +		i2c34 = &i2c14mux1chn3;
> +		i2c35 = &i2c15mux0chn0;
> +		i2c36 = &i2c15mux0chn1;
> +		i2c37 = &i2c15mux0chn2;
> +		i2c38 = &i2c15mux0chn3;
> +		i2c39 = &i2c15mux1chn0;
> +		i2c40 = &i2c15mux1chn1;
> +		i2c41 = &i2c15mux1chn2;
> +		i2c42 = &i2c15mux1chn3;
> +		i2c43 = &i2c15mux2chn0;
> +		i2c44 = &i2c15mux2chn1;
> +		i2c45 = &i2c15mux2chn2;
> +		i2c46 = &i2c15mux2chn3;
> +		i2c47 = &i2c8mux0chn0;
> +		i2c48 = &i2c8mux0chn1;
> +
> +		serial4 = &uart5;
> +
> +		sbefifo500 = &sbefifo500;
> +		sbefifo501 = &sbefifo501;
> +		sbefifo510 = &sbefifo510;
> +		sbefifo511 = &sbefifo511;
> +		sbefifo512 = &sbefifo512;
> +		sbefifo513 = &sbefifo513;
> +		sbefifo514 = &sbefifo514;
> +		sbefifo515 = &sbefifo515;
> +		sbefifo602 = &sbefifo602;
> +		sbefifo603 = &sbefifo603;
> +		sbefifo610 = &sbefifo610;
> +		sbefifo611 = &sbefifo611;
> +		sbefifo614 = &sbefifo614;
> +		sbefifo615 = &sbefifo615;
> +		sbefifo616 = &sbefifo616;
> +		sbefifo617 = &sbefifo617;
> +		sbefifo700 = &sbefifo700;
> +		sbefifo701 = &sbefifo701;
> +		sbefifo710 = &sbefifo710;
> +		sbefifo711 = &sbefifo711;
> +		sbefifo712 = &sbefifo712;
> +		sbefifo713 = &sbefifo713;
> +		sbefifo714 = &sbefifo714;
> +		sbefifo715 = &sbefifo715;
> +		sbefifo802 = &sbefifo802;
> +		sbefifo803 = &sbefifo803;
> +		sbefifo810 = &sbefifo810;
> +		sbefifo811 = &sbefifo811;
> +		sbefifo814 = &sbefifo814;
> +		sbefifo815 = &sbefifo815;
> +		sbefifo816 = &sbefifo816;
> +		sbefifo817 = &sbefifo817;
> +
> +		scom500 = &scom500;
> +		scom501 = &scom501;
> +		scom510 = &scom510;
> +		scom511 = &scom511;
> +		scom512 = &scom512;
> +		scom513 = &scom513;
> +		scom514 = &scom514;
> +		scom515 = &scom515;
> +		scom602 = &scom602;
> +		scom603 = &scom603;
> +		scom610 = &scom610;
> +		scom611 = &scom611;
> +		scom614 = &scom614;
> +		scom615 = &scom615;
> +		scom616 = &scom616;
> +		scom617 = &scom617;
> +		scom700 = &scom700;
> +		scom701 = &scom701;
> +		scom710 = &scom710;
> +		scom711 = &scom711;
> +		scom712 = &scom712;
> +		scom713 = &scom713;
> +		scom714 = &scom714;
> +		scom715 = &scom715;
> +		scom802 = &scom802;
> +		scom803 = &scom803;
> +		scom810 = &scom810;
> +		scom811 = &scom811;
> +		scom814 = &scom814;
> +		scom815 = &scom815;
> +		scom816 = &scom816;
> +		scom817 = &scom817;
> +
> +		spi50 = &cfam4_spi0;
> +		spi51 = &cfam4_spi1;
> +		spi52 = &cfam4_spi2;
> +		spi53 = &cfam4_spi3;
> +		spi60 = &cfam5_spi0;
> +		spi61 = &cfam5_spi1;
> +		spi62 = &cfam5_spi2;
> +		spi63 = &cfam5_spi3;
> +		spi70 = &cfam6_spi0;
> +		spi71 = &cfam6_spi1;
> +		spi72 = &cfam6_spi2;
> +		spi73 = &cfam6_spi3;
> +		spi80 = &cfam7_spi0;
> +		spi81 = &cfam7_spi1;
> +		spi82 = &cfam7_spi2;
> +		spi83 = &cfam7_spi3;
> +	};
> +
> +	chosen {
> +		stdout-path = &uart5;
> +		bootargs = "console=ttyS4,115200n8";


Drop bootargs. Everywhere.

> +	};
> +
> +	memory at 80000000 {
> +		device_type = "memory";
> +		reg = <0x80000000 0x40000000>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		event_log: tcg_event_log at b3d00000 {

Same problem



> +
> +	usb_power-hog {

No underscores.

> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
> +		output-high;
> +	};
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	eeprom at 51 {
> +		compatible = "atmel,24c64";
> +		reg = <0x51>;
> +	};
> +
> +	pca1: pca9552 at 62 {

All my previous comments apply.



Best regards,
Krzysztof

Re: [PATCH v3 14/14] ARM: dts: aspeed: Add IBM P11 Fuji BMC system

[Krzysztof Kozlowski]

On 25/04/2024 23:37, Eddie James wrote:
> Add the device tree for the new BMC system. The Fuji is a P11
> system with eight processors.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  arch/arm/boot/dts/aspeed/Makefile             |    2 +
>  .../boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts   | 3984 +++++++++++++++++
>  2 files changed, 3986 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
> 
> diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
> index 715106b3baa1..783409b7c206 100644
> --- a/arch/arm/boot/dts/aspeed/Makefile
> +++ b/arch/arm/boot/dts/aspeed/Makefile
> @@ -33,8 +33,10 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>  	aspeed-bmc-facebook-yamp.dtb \
>  	aspeed-bmc-facebook-yosemitev2.dtb \
>  	aspeed-bmc-facebook-yosemite4.dtb \
> +	aspeed-bmc-ibm-blueridge.dtb \
>  	aspeed-bmc-ibm-bonnell.dtb \
>  	aspeed-bmc-ibm-everest.dtb \
> +	aspeed-bmc-ibm-fuji.dtb \
>  	aspeed-bmc-ibm-rainier.dtb \
>  	aspeed-bmc-ibm-rainier-1s4u.dtb \
>  	aspeed-bmc-ibm-rainier-4u.dtb \
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
> new file mode 100644
> index 000000000000..dc41fa815761
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
> @@ -0,0 +1,3984 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2024 IBM Corp.
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/i2c/i2c.h>
> +#include <dt-bindings/leds/leds-pca955x.h>
> +
> +/ {
> +	model = "Fuji";
> +	compatible = "ibm,fuji-bmc", "aspeed,ast2600";
> +
> +	aliases {
> +		i2c500 = &cfam4_i2c0;
> +		i2c501 = &cfam4_i2c1;
> +		i2c510 = &cfam4_i2c10;
> +		i2c511 = &cfam4_i2c11;
> +		i2c512 = &cfam4_i2c12;
> +		i2c513 = &cfam4_i2c13;
> +		i2c514 = &cfam4_i2c14;
> +		i2c515 = &cfam4_i2c15;
> +		i2c602 = &cfam5_i2c2;
> +		i2c603 = &cfam5_i2c3;
> +		i2c610 = &cfam5_i2c10;
> +		i2c611 = &cfam5_i2c11;
> +		i2c614 = &cfam5_i2c14;
> +		i2c615 = &cfam5_i2c15;
> +		i2c616 = &cfam5_i2c16;
> +		i2c617 = &cfam5_i2c17;
> +		i2c700 = &cfam6_i2c0;
> +		i2c701 = &cfam6_i2c1;
> +		i2c710 = &cfam6_i2c10;
> +		i2c711 = &cfam6_i2c11;
> +		i2c712 = &cfam6_i2c12;
> +		i2c713 = &cfam6_i2c13;
> +		i2c714 = &cfam6_i2c14;
> +		i2c715 = &cfam6_i2c15;
> +		i2c802 = &cfam7_i2c2;
> +		i2c803 = &cfam7_i2c3;
> +		i2c810 = &cfam7_i2c10;
> +		i2c811 = &cfam7_i2c11;
> +		i2c814 = &cfam7_i2c14;
> +		i2c815 = &cfam7_i2c15;
> +		i2c816 = &cfam7_i2c16;
> +		i2c817 = &cfam7_i2c17;
> +
> +		i2c16 = &i2c4mux0chn0;
> +		i2c17 = &i2c4mux0chn1;
> +		i2c18 = &i2c4mux0chn2;
> +		i2c19 = &i2c5mux0chn0;
> +		i2c20 = &i2c5mux0chn1;
> +		i2c21 = &i2c5mux0chn2;
> +		i2c22 = &i2c5mux0chn3;
> +		i2c23 = &i2c6mux0chn0;
> +		i2c24 = &i2c6mux0chn1;
> +		i2c25 = &i2c6mux0chn2;
> +		i2c26 = &i2c6mux0chn3;
> +		i2c27 = &i2c14mux0chn0;
> +		i2c28 = &i2c14mux0chn1;
> +		i2c29 = &i2c14mux0chn2;
> +		i2c30 = &i2c14mux0chn3;
> +		i2c31 = &i2c14mux1chn0;
> +		i2c32 = &i2c14mux1chn1;
> +		i2c33 = &i2c14mux1chn2;
> +		i2c34 = &i2c14mux1chn3;
> +		i2c35 = &i2c15mux0chn0;
> +		i2c36 = &i2c15mux0chn1;
> +		i2c37 = &i2c15mux0chn2;
> +		i2c38 = &i2c15mux0chn3;
> +		i2c39 = &i2c15mux1chn0;
> +		i2c40 = &i2c15mux1chn1;
> +		i2c41 = &i2c15mux1chn2;
> +		i2c42 = &i2c15mux1chn3;
> +		i2c43 = &i2c15mux2chn0;
> +		i2c44 = &i2c15mux2chn1;
> +		i2c45 = &i2c15mux2chn2;
> +		i2c46 = &i2c15mux2chn3;
> +		i2c47 = &i2c8mux0chn0;
> +		i2c48 = &i2c8mux0chn1;
> +
> +		serial4 = &uart5;
> +
> +		sbefifo500 = &sbefifo500;
> +		sbefifo501 = &sbefifo501;
> +		sbefifo510 = &sbefifo510;
> +		sbefifo511 = &sbefifo511;
> +		sbefifo512 = &sbefifo512;
> +		sbefifo513 = &sbefifo513;
> +		sbefifo514 = &sbefifo514;
> +		sbefifo515 = &sbefifo515;
> +		sbefifo602 = &sbefifo602;
> +		sbefifo603 = &sbefifo603;
> +		sbefifo610 = &sbefifo610;
> +		sbefifo611 = &sbefifo611;
> +		sbefifo614 = &sbefifo614;
> +		sbefifo615 = &sbefifo615;
> +		sbefifo616 = &sbefifo616;
> +		sbefifo617 = &sbefifo617;
> +		sbefifo700 = &sbefifo700;
> +		sbefifo701 = &sbefifo701;
> +		sbefifo710 = &sbefifo710;
> +		sbefifo711 = &sbefifo711;
> +		sbefifo712 = &sbefifo712;
> +		sbefifo713 = &sbefifo713;
> +		sbefifo714 = &sbefifo714;
> +		sbefifo715 = &sbefifo715;
> +		sbefifo802 = &sbefifo802;
> +		sbefifo803 = &sbefifo803;
> +		sbefifo810 = &sbefifo810;
> +		sbefifo811 = &sbefifo811;
> +		sbefifo814 = &sbefifo814;
> +		sbefifo815 = &sbefifo815;
> +		sbefifo816 = &sbefifo816;
> +		sbefifo817 = &sbefifo817;
> +
> +		scom500 = &scom500;
> +		scom501 = &scom501;
> +		scom510 = &scom510;
> +		scom511 = &scom511;
> +		scom512 = &scom512;
> +		scom513 = &scom513;
> +		scom514 = &scom514;
> +		scom515 = &scom515;
> +		scom602 = &scom602;
> +		scom603 = &scom603;
> +		scom610 = &scom610;
> +		scom611 = &scom611;
> +		scom614 = &scom614;
> +		scom615 = &scom615;
> +		scom616 = &scom616;
> +		scom617 = &scom617;
> +		scom700 = &scom700;
> +		scom701 = &scom701;
> +		scom710 = &scom710;
> +		scom711 = &scom711;
> +		scom712 = &scom712;
> +		scom713 = &scom713;
> +		scom714 = &scom714;
> +		scom715 = &scom715;
> +		scom802 = &scom802;
> +		scom803 = &scom803;
> +		scom810 = &scom810;
> +		scom811 = &scom811;
> +		scom814 = &scom814;
> +		scom815 = &scom815;
> +		scom816 = &scom816;
> +		scom817 = &scom817;
> +
> +		spi50 = &cfam4_spi0;
> +		spi51 = &cfam4_spi1;
> +		spi52 = &cfam4_spi2;
> +		spi53 = &cfam4_spi3;
> +		spi60 = &cfam5_spi0;
> +		spi61 = &cfam5_spi1;
> +		spi62 = &cfam5_spi2;
> +		spi63 = &cfam5_spi3;
> +		spi70 = &cfam6_spi0;
> +		spi71 = &cfam6_spi1;
> +		spi72 = &cfam6_spi2;
> +		spi73 = &cfam6_spi3;
> +		spi80 = &cfam7_spi0;
> +		spi81 = &cfam7_spi1;
> +		spi82 = &cfam7_spi2;
> +		spi83 = &cfam7_spi3;
> +	};
> +
> +	chosen {
> +		stdout-path = &uart5;
> +		bootargs = "console=ttyS4,115200n8";


Drop bootargs. Everywhere.

> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		reg = <0x80000000 0x40000000>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		event_log: tcg_event_log@b3d00000 {

Same problem



> +
> +	usb_power-hog {

No underscores.

> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
> +		output-high;
> +	};
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	eeprom@51 {
> +		compatible = "atmel,24c64";
> +		reg = <0x51>;
> +	};
> +
> +	pca1: pca9552@62 {

All my previous comments apply.



Best regards,
Krzysztof

Re: [PATCH v3 00/14] ARM: dts: aspeed: Add IBM P11 BMC Boards

[Rob Herring]

On Thu, 25 Apr 2024 16:36:47 -0500, Eddie James wrote:
> Add the Blueridge and Fuji BMC systems. Document many missing FSI related
> properties, and fix existing warnings.
> 
> Changes since v2:
>  - Split up the DTS patches
>  - Add documentation patches
> 
> Eddie James (14):
>   dt-bindings: spi: Document the IBM Power SPI controller
>   dt-bindings: fsi: fsi2spi: Document SPI controller child nodes
>   dt-bindings: fsi: Document the FSI2PIB engine
>   dt-bindings: fsi: p9-occ: Switch to yaml format
>   dt-bindings: fsi: Document the IBM SBEFIFO engine
>   dt-bindings: fsi: Document the FSI controller common properties
>   dt-bindings: fsi: ibm,i2cr-fsi-master: Reference common FSI controller
>   dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format
>   dt-bindings: fsi: Document the FSI Hub Controller
>   dt-bindings: i2c: i2c-fsi: Switch to yaml format
>   dt-bindings: arm: aspeed: add IBM P11 BMC boards
>   ARM: dts: aspeed: Add IBM P11 FSI devices
>   ARM: dts: aspeed: Add IBM P11 Blueridge BMC system
>   ARM: dts: aspeed: Add IBM P11 Fuji BMC system
> 
>  .../bindings/arm/aspeed/aspeed.yaml           |    2 +
>  .../fsi/aspeed,ast2600-fsi-master.yaml        |   72 +
>  .../bindings/fsi/fsi-controller.yaml          |   65 +
>  .../bindings/fsi/fsi-master-aspeed.txt        |   36 -
>  .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  |   38 +
>  .../devicetree/bindings/fsi/ibm,fsi2spi.yaml  |   11 +
>  .../bindings/fsi/ibm,hub-fsi-controller.yaml  |   44 +
>  .../bindings/fsi/ibm,i2cr-fsi-master.yaml     |    5 +-
>  .../devicetree/bindings/fsi/ibm,p9-occ.txt    |   16 -
>  .../devicetree/bindings/fsi/ibm,p9-occ.yaml   |   41 +
>  .../bindings/fsi/ibm,p9-sbefifo.yaml          |   50 +
>  .../devicetree/bindings/i2c/i2c-fsi.txt       |   40 -
>  .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  |   59 +
>  .../devicetree/bindings/spi/ibm,p10-spi.yaml  |   56 +
>  arch/arm/boot/dts/aspeed/Makefile             |    2 +
>  .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++
>  .../boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts   | 3984 +++++++++++++++++
>  .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++
>  18 files changed, 7835 insertions(+), 93 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>  create mode 100644 Documentation/devicetree/bindings/fsi/fsi-controller.yaml
>  delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
>  delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml
>  delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
>  create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
>  create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
>  create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
> 
> --
> 2.39.3
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y aspeed/aspeed-bmc-ibm-blueridge.dtb aspeed/aspeed-bmc-ibm-fuji.dtb' for 20240425213701.655540-1-eajames@linux.ibm.com:

arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: timer: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /sdram@1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: timer: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /sdram@1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: bus@1e600000: compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
	from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: bus@1e600000: compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
	from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac@1e660000: $nodename:0: 'ftgmac@1e660000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac@1e680000: $nodename:0: 'ftgmac@1e680000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac@1e670000: $nodename:0: 'ftgmac@1e670000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac@1e670000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac@1e690000: $nodename:0: 'ftgmac@1e690000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac@1e690000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac@1e660000: $nodename:0: 'ftgmac@1e660000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac@1e680000: $nodename:0: 'ftgmac@1e680000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac@1e670000: $nodename:0: 'ftgmac@1e670000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac@1e670000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac@1e690000: $nodename:0: 'ftgmac@1e690000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac@1e690000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: syscon@1e6e2000: pinctrl: 
'oneOf' conditional failed, one must be fixed:
	'aspeed,external-nodes' is a required property
	'aspeed,ast2400-pinctrl' was expected
	'aspeed,ast2500-pinctrl' was expected
	'EMMC' is not one of ['ACPI', 'ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'DDCCLK', 'DDCDAT', 'EXTRST', 'FLACK', 'FLBUSY', 'FLWP', 'GPID', 'GPID0', 'GPID2', 'GPID4', 'GPID6', 'GPIE0', 'GPIE2', 'GPIE4', 'GPIE6', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'LPCPD', 'LPCPME', 'LPCRST', 'LPCSMI', 'MAC1LINK', 'MAC2LINK', 'MDIO1', 'MDIO2', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NDTS4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'OSCCLK', 'PWM0', 'PWM1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'RGMII1', 'RGMII2', 'RMII1', 'RMII2', 'ROM16', 'ROM8', 'ROMCS1', 'ROMCS2', 'ROMCS3', 'ROMCS4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT2', 'SALT3', 'SALT4', 'SD1', 'SD2', 'SGPMCK', 'SGPMI', 'SGPMLD', 'SGPMO', 'SGPSCK', 'SGPSI0', 'SGPSI1', 'SGPSLD', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1DEBUG', 'SPI1PASSTHRU', 'SPICS1', 'TIMER3', 'TIMER4', 'TIMER5', 'TIMER6', 'TIMER7', 'TIMER8', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART6', 'USB11D1', 'USB11H2', 'USB2D1', 'USB2H1', 'USBCKI', 'VGABIOS_ROM', 'VGAHS', 'VGAVS', 'VPI18', 'VPI24', 'VPI30', 'VPO12', 'VPO24', 'WDTRST1', 'WDTRST2']
	'EMMC' is not one of ['ACPI', 'ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'DDCCLK', 'DDCDAT', 'ESPI', 'FWSPICS1', 'FWSPICS2', 'GPID0', 'GPID2', 'GPID4', 'GPID6', 'GPIE0', 'GPIE2', 'GPIE4', 'GPIE6', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'LAD0', 'LAD1', 'LAD2', 'LAD3', 'LCLK', 'LFRAME', 'LPCHC', 'LPCPD', 'LPCPLUS', 'LPCPME', 'LPCRST', 'LPCSMI', 'LSIRQ', 'MAC1LINK', 'MAC2LINK', 'MDIO1', 'MDIO2', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PNOR', 'PWM0', 'PWM1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'RGMII1', 'RGMII2', 'RMII1', 'RMII2', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SCL1', 'SCL2', 'SD1', 'SD2', 'SDA1', 'SDA2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1CS1', 'SPI1DEBUG', 'SPI1PASSTHRU', 'SPI2CK', 'SPI2CS0', 'SPI2CS1', 'SPI2MISO', 'SPI2MOSI', 'TIMER3', 'TIMER4', 'TIMER5', 'TIMER6', 'TIMER7', 'TIMER8', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART6', 'USB11BHID', 'USB2AD', 'USB2AH', 'USB2BD', 'USB2BH', 'USBCKI', 'VGABIOSROM', 'VGAHS', 'VGAVS', 'VPI24', 'VPO', 'WDTRST1', 'WDTRST2']
...
	from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: syscon@1e6e2000: 'smp-memram@180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^silicon-id@[0-9a-f]+$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: syscon@1e6e2000: 'smp-memram@180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^silicon-id@[0-9a-f]+$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: usb11bhid_default:function:0: 'USB11BHID' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: i3c1_default:function:0: 'I3C1' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: i3c1_default:groups:0: 'I3C1' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMCG1', 'EMMCG4', 'EMMCG8', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'HVI3C3', 'HVI3C4', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10G0', 'PWM10G1', 'PWM11G0', 'PWM11G1', 'PWM12G0', 'PWM12G1', 'PWM13G0', 'PWM13G1', 'PWM14G0', 'PWM14G1', 'PWM15G0', 'PWM15G1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8G0', 'PWM8G1', 'PWM9G0', 'PWM9G1', 'QSPI1', 'QSPI2', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10G0', 'SALT10G1', 'SALT11G0', 'SALT11G1', 'SALT12G0', 'SALT12G1', 'SALT13G0', 'SALT13G1', 'SALT14G0', 'SALT14G1', 'SALT15G0', 'SALT15G1', 'SALT16G0', 'SALT16G1', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9G0', 'SALT9G1', 'SD1', 'SD2', 'SD3', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12G0', 'UART12G1', 'UART13G0', 'UART13G1', 'UART6', 'UART7', 'UART8', 'UART9', 'USBA', 'USBB', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: i3c1_default:function:0: 'I3C1' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: i3c1_default:groups:0: 'I3C1' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMCG1', 'EMMCG4', 'EMMCG8', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'HVI3C3', 'HVI3C4', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10G0', 'PWM10G1', 'PWM11G0', 'PWM11G1', 'PWM12G0', 'PWM12G1', 'PWM13G0', 'PWM13G1', 'PWM14G0', 'PWM14G1', 'PWM15G0', 'PWM15G1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8G0', 'PWM8G1', 'PWM9G0', 'PWM9G1', 'QSPI1', 'QSPI2', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10G0', 'SALT10G1', 'SALT11G0', 'SALT11G1', 'SALT12G0', 'SALT12G1', 'SALT13G0', 'SALT13G1', 'SALT14G0', 'SALT14G1', 'SALT15G0', 'SALT15G1', 'SALT16G0', 'SALT16G1', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9G0', 'SALT9G1', 'SD1', 'SD2', 'SD3', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12G0', 'UART12G1', 'UART13G0', 'UART13G1', 'UART6', 'UART7', 'UART8', 'UART9', 'USBA', 'USBB', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: i3c2_default:function:0: 'I3C2' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: i3c2_default:groups:0: 'I3C2' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMCG1', 'EMMCG4', 'EMMCG8', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'HVI3C3', 'HVI3C4', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10G0', 'PWM10G1', 'PWM11G0', 'PWM11G1', 'PWM12G0', 'PWM12G1', 'PWM13G0', 'PWM13G1', 'PWM14G0', 'PWM14G1', 'PWM15G0', 'PWM15G1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8G0', 'PWM8G1', 'PWM9G0', 'PWM9G1', 'QSPI1', 'QSPI2', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10G0', 'SALT10G1', 'SALT11G0', 'SALT11G1', 'SALT12G0', 'SALT12G1', 'SALT13G0', 'SALT13G1', 'SALT14G0', 'SALT14G1', 'SALT15G0', 'SALT15G1', 'SALT16G0', 'SALT16G1', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9G0', 'SALT9G1', 'SD1', 'SD2', 'SD3', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12G0', 'UART12G1', 'UART13G0', 'UART13G1', 'UART6', 'UART7', 'UART8', 'UART9', 'USBA', 'USBB', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: usb2ad_default:function:0: 'USB2AD' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: i3c2_default:function:0: 'I3C2' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: i3c2_default:groups:0: 'I3C2' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMCG1', 'EMMCG4', 'EMMCG8', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'HVI3C3', 'HVI3C4', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10G0', 'PWM10G1', 'PWM11G0', 'PWM11G1', 'PWM12G0', 'PWM12G1', 'PWM13G0', 'PWM13G1', 'PWM14G0', 'PWM14G1', 'PWM15G0', 'PWM15G1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8G0', 'PWM8G1', 'PWM9G0', 'PWM9G1', 'QSPI1', 'QSPI2', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10G0', 'SALT10G1', 'SALT11G0', 'SALT11G1', 'SALT12G0', 'SALT12G1', 'SALT13G0', 'SALT13G1', 'SALT14G0', 'SALT14G1', 'SALT15G0', 'SALT15G1', 'SALT16G0', 'SALT16G1', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9G0', 'SALT9G1', 'SD1', 'SD2', 'SD3', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12G0', 'UART12G1', 'UART13G0', 'UART13G1', 'UART6', 'UART7', 'UART8', 'UART9', 'USBA', 'USBB', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: usb2ad_default:function:0: 'USB2AD' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: usb11bhid_default:function:0: 'USB11BHID' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/syscon@1e6e2000/smp-memram@180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@560: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic0']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@570: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic1']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/display@1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/xdma@1e6e7000: failed to match any schema with compatible: ['aspeed,ast2600-xdma']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: adc@1e6e9000: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: adc@1e6e9100: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/syscon@1e6e2000/smp-memram@180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: crypto@1e6fa000: 'aspeed,ahbc' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@560: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic0']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/syscon@1e6e2000/interrupt-controller@570: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic1']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/video@1e700000: failed to match any schema with compatible: ['aspeed,ast2600-video-engine']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: gpio@1e780000: 'i2c3_mux_oe_n-hog', 'usb_power-hog' do not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,ast2400-gpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/display@1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: sgpiom@1e780500: '#interrupt-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/xdma@1e6e7000: failed to match any schema with compatible: ['aspeed,ast2600-xdma']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: adc@1e6e9000: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: sgpiom@1e780600: '#interrupt-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: adc@1e6e9100: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: crypto@1e6fa000: 'aspeed,ahbc' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/timer@1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/video@1e700000: failed to match any schema with compatible: ['aspeed,ast2600-video-engine']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: gpio@1e780000: 'usb_power-hog' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,ast2400-gpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: sgpiom@1e780500: '#interrupt-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: sgpiom@1e780600: '#interrupt-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: lpc@1e789000: lpc-snoop@80: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: lpc@1e789000: reg-io-width: [[4]] is not of type 'object'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/timer@1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: kcs@24: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: kcs@28: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: kcs@2c: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: kcs@114: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/lpc@1e789000/lhc@a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: lpc@1e789000: lpc-snoop@80: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: lpc@1e789000: reg-io-width: [[4]] is not of type 'object'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: kcs@24: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/lpc@1e789000/ibt@140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: sdc@1e740000: sdhci@1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: sdc@1e740000: sdhci@1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: kcs@28: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: kcs@2c: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: kcs@114: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/lpc@1e789000/lhc@a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/lpc@1e789000/ibt@140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: sdc@1e740000: sdhci@1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: sdc@1e740000: sdhci@1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@200/pca9552@61: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@80/pca9552@62: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@280/i2c-mux@70/i2c@0/pca9551@60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@280/pca9552@65: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@280/i2c-mux@70/i2c@0/pca9551@62: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@300/i2c-mux@70/i2c@0/pca9551@60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@280/i2c-mux@70/i2c@1/pca9551@60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@300/i2c-mux@70/i2c@1/pca9551@61: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@280/i2c-mux@70/i2c@2/pca9551@61: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@300/pca9552@66: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@300/i2c-mux@70/i2c@0/pca9551@60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@300/i2c-mux@70/i2c@1/pca9551@61: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@30: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@300/i2c-mux@70/i2c@2/pca9551@62: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@300/i2c-mux@70/i2c@3/pca9551@63: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@31: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@380/i2c-mux@70/i2c@0/pca9551@60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@380/i2c-mux@70/i2c@1/pca9551@62: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@32: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@380/i2c-mux@70/i2c@2/pca9551@63: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@380/i2c-mux@70/i2c@3/pca9551@61: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@380/pca9552@65: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@33: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@31: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/max31785@52: failed to match any schema with compatible: ['maxim,max31785a']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9551@60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@61: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@32: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: dps310@76: '#io-channel-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@33: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@480/pca9552@60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@480/pca9552@61: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@30: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@600/i2c-mux@70/i2c@0/pca9551@60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@34: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@700/pca9552@60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@400/pca9552@35: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@780/pca9552@60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus@1e78a000/i2c-bus@800/pca9552@60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: fsi@1e79b000: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: fsi@1e79b000: Unevaluated properties are not allowed ('#interrupt-cells', 'compatible', 'interrupt-controller' were unexpected)
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/fsi@1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@780/i2c-mux@70/i2c@2/pca9551@60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@780/i2c-mux@70/i2c@3/max31785@52: failed to match any schema with compatible: ['maxim,max31785a']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@780/i2c-mux@70/i2c@3/pca9552@60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus@1e78a000/i2c-bus@780/i2c-mux@70/i2c@3/pca9552@61: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: fsi@1e79b000: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: fsi@1e79b000: Unevaluated properties are not allowed ('#interrupt-cells', 'compatible', 'interrupt-controller' were unexpected)
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/fsi@1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: fsi@1e79b100: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/fsi@1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/dma-controller@1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: fsi@1e79b100: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/fsi@1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/dma-controller@1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']

[PATCH v3 00/14] ARM: dts: aspeed: Add IBM P11 BMC Boards

[Rob Herring]

On Thu, 25 Apr 2024 16:36:47 -0500, Eddie James wrote:
> Add the Blueridge and Fuji BMC systems. Document many missing FSI related
> properties, and fix existing warnings.
> 
> Changes since v2:
>  - Split up the DTS patches
>  - Add documentation patches
> 
> Eddie James (14):
>   dt-bindings: spi: Document the IBM Power SPI controller
>   dt-bindings: fsi: fsi2spi: Document SPI controller child nodes
>   dt-bindings: fsi: Document the FSI2PIB engine
>   dt-bindings: fsi: p9-occ: Switch to yaml format
>   dt-bindings: fsi: Document the IBM SBEFIFO engine
>   dt-bindings: fsi: Document the FSI controller common properties
>   dt-bindings: fsi: ibm,i2cr-fsi-master: Reference common FSI controller
>   dt-bindings: fsi: ast2600-fsi-master: Switch to yaml format
>   dt-bindings: fsi: Document the FSI Hub Controller
>   dt-bindings: i2c: i2c-fsi: Switch to yaml format
>   dt-bindings: arm: aspeed: add IBM P11 BMC boards
>   ARM: dts: aspeed: Add IBM P11 FSI devices
>   ARM: dts: aspeed: Add IBM P11 Blueridge BMC system
>   ARM: dts: aspeed: Add IBM P11 Fuji BMC system
> 
>  .../bindings/arm/aspeed/aspeed.yaml           |    2 +
>  .../fsi/aspeed,ast2600-fsi-master.yaml        |   72 +
>  .../bindings/fsi/fsi-controller.yaml          |   65 +
>  .../bindings/fsi/fsi-master-aspeed.txt        |   36 -
>  .../devicetree/bindings/fsi/ibm,fsi2pib.yaml  |   38 +
>  .../devicetree/bindings/fsi/ibm,fsi2spi.yaml  |   11 +
>  .../bindings/fsi/ibm,hub-fsi-controller.yaml  |   44 +
>  .../bindings/fsi/ibm,i2cr-fsi-master.yaml     |    5 +-
>  .../devicetree/bindings/fsi/ibm,p9-occ.txt    |   16 -
>  .../devicetree/bindings/fsi/ibm,p9-occ.yaml   |   41 +
>  .../bindings/fsi/ibm,p9-sbefifo.yaml          |   50 +
>  .../devicetree/bindings/i2c/i2c-fsi.txt       |   40 -
>  .../devicetree/bindings/i2c/ibm,i2c-fsi.yaml  |   59 +
>  .../devicetree/bindings/spi/ibm,p10-spi.yaml  |   56 +
>  arch/arm/boot/dts/aspeed/Makefile             |    2 +
>  .../dts/aspeed/aspeed-bmc-ibm-blueridge.dts   | 1711 +++++++
>  .../boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts   | 3984 +++++++++++++++++
>  .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 1696 +++++++
>  18 files changed, 7835 insertions(+), 93 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/fsi/aspeed,ast2600-fsi-master.yaml
>  create mode 100644 Documentation/devicetree/bindings/fsi/fsi-controller.yaml
>  delete mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-aspeed.txt
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2pib.yaml
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,hub-fsi-controller.yaml
>  delete mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.txt
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-occ.yaml
>  create mode 100644 Documentation/devicetree/bindings/fsi/ibm,p9-sbefifo.yaml
>  delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-fsi.txt
>  create mode 100644 Documentation/devicetree/bindings/i2c/ibm,i2c-fsi.yaml
>  create mode 100644 Documentation/devicetree/bindings/spi/ibm,p10-spi.yaml
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
>  create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
> 
> --
> 2.39.3
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y aspeed/aspeed-bmc-ibm-blueridge.dtb aspeed/aspeed-bmc-ibm-fuji.dtb' for 20240425213701.655540-1-eajames at linux.ibm.com:

arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: timer: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /sdram at 1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: timer: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /sdram at 1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: bus at 1e600000: compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
	from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: bus at 1e600000: compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
	from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac at 1e660000: $nodename:0: 'ftgmac at 1e660000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac at 1e680000: $nodename:0: 'ftgmac at 1e680000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac at 1e670000: $nodename:0: 'ftgmac at 1e670000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac at 1e670000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac at 1e690000: $nodename:0: 'ftgmac at 1e690000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: ftgmac at 1e690000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac at 1e660000: $nodename:0: 'ftgmac at 1e660000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac at 1e680000: $nodename:0: 'ftgmac at 1e680000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac at 1e670000: $nodename:0: 'ftgmac at 1e670000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac at 1e670000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac at 1e690000: $nodename:0: 'ftgmac at 1e690000' does not match '^ethernet(@.*)?$'
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: ftgmac at 1e690000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
	from schema $id: http://devicetree.org/schemas/net/faraday,ftgmac100.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: syscon at 1e6e2000: pinctrl: 
'oneOf' conditional failed, one must be fixed:
	'aspeed,external-nodes' is a required property
	'aspeed,ast2400-pinctrl' was expected
	'aspeed,ast2500-pinctrl' was expected
	'EMMC' is not one of ['ACPI', 'ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'DDCCLK', 'DDCDAT', 'EXTRST', 'FLACK', 'FLBUSY', 'FLWP', 'GPID', 'GPID0', 'GPID2', 'GPID4', 'GPID6', 'GPIE0', 'GPIE2', 'GPIE4', 'GPIE6', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'LPCPD', 'LPCPME', 'LPCRST', 'LPCSMI', 'MAC1LINK', 'MAC2LINK', 'MDIO1', 'MDIO2', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NDTS4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'OSCCLK', 'PWM0', 'PWM1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'RGMII1', 'RGMII2', 'RMII1', 'RMII2', 'ROM16', 'ROM8', 'ROMCS1', 'ROMCS2', 'ROMCS3', 'ROMCS4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT2', 'SALT3', 'SALT4', 'SD1', 'SD2', 'SGPMCK', 'SGPMI', 'SGPMLD', 'SGPMO', 'SG
 PSCK', 'SGPSI0', 'SGPSI1', 'SGPSLD', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1DEBUG', 'SPI1PASSTHRU', 'SPICS1', 'TIMER3', 'TIMER4', 'TIMER5', 'TIMER6', 'TIMER7', 'TIMER8', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART6', 'USB11D1', 'USB11H2', 'USB2D1', 'USB2H1', 'USBCKI', 'VGABIOS_ROM', 'VGAHS', 'VGAVS', 'VPI18', 'VPI24', 'VPI30', 'VPO12', 'VPO24', 'WDTRST1', 'WDTRST2']
	'EMMC' is not one of ['ACPI', 'ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'DDCCLK', 'DDCDAT', 'ESPI', 'FWSPICS1', 'FWSPICS2', 'GPID0', 'GPID2', 'GPID4', 'GPID6', 'GPIE0', 'GPIE2', 'GPIE4', 'GPIE6', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'LAD0', 'LAD1', 'LAD2', 'LAD3', 'LCLK', 'LFRAME', 'LPCHC', 'LPCPD', 'LPCPLUS', 'LPCPME', 'LPCRST', 'LPCSMI', 'LSIRQ', 'MAC1LINK', 'MAC2LINK', 'MDIO1', 'MDIO2', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PNOR', 'PWM0', 'PWM1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'RGMII1', 'RGMII2', 'RMII1', 'RMII2', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT
 2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SCL1', 'SCL2', 'SD1', 'SD2', 'SDA1', 'SDA2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1CS1', 'SPI1DEBUG', 'SPI1PASSTHRU', 'SPI2CK', 'SPI2CS0', 'SPI2CS1', 'SPI2MISO', 'SPI2MOSI', 'TIMER3', 'TIMER4', 'TIMER5', 'TIMER6', 'TIMER7', 'TIMER8', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART6', 'USB11BHID', 'USB2AD', 'USB2AH', 'USB2BD', 'USB2BH', 'USBCKI', 'VGABIOSROM', 'VGAHS', 'VGAVS', 'VPI24', 'VPO', 'WDTRST1', 'WDTRST2']
...
	from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: syscon at 1e6e2000: 'smp-memram at 180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^silicon-id@[0-9a-f]+$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: syscon at 1e6e2000: 'smp-memram at 180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^silicon-id@[0-9a-f]+$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: usb11bhid_default:function:0: 'USB11BHID' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 
 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD',
  'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: i3c1_default:function:0: 'I3C1' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS
 1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB
 2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: i3c1_default:groups:0: 'I3C1' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMCG1', 'EMMCG4', 'EMMCG8', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'HVI3C3', 'HVI3C4', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4
 ', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10G0', 'PWM10G1', 'PWM11G0', 'PWM11G1', 'PWM12G0', 'PWM12G1', 'PWM13G0', 'PWM13G1', 'PWM14G0', 'PWM14G1', 'PWM15G0', 'PWM15G1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8G0', 'PWM8G1', 'PWM9G0', 'PWM9G1', 'QSPI1', 'QSPI2', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10G0', 'SALT10G1', 'SALT11G0', 'SALT11G1', 'SALT12G0', 'SALT12G1', 'SALT13G0', 'SALT13G1', 'SALT14G0', 'SALT14G1', 'SALT15G0', 'SALT15G1', 'SALT16G0', 'SALT16G1', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9G0', 'SALT9G1', 'SD1', 'SD2', 'SD3', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'T
 ACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12G0', 'UART12G1', 'UART13G0', 'UART13G1', 'UART6', 'UART7', 'UART8', 'UART9', 'USBA', 'USBB', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: i3c1_default:function:0: 'I3C1' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', '
 NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH',
  'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: i3c1_default:groups:0: 'I3C1' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMCG1', 'EMMCG4', 'EMMCG8', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'HVI3C3', 'HVI3C4', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'N
 RI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10G0', 'PWM10G1', 'PWM11G0', 'PWM11G1', 'PWM12G0', 'PWM12G1', 'PWM13G0', 'PWM13G1', 'PWM14G0', 'PWM14G1', 'PWM15G0', 'PWM15G1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8G0', 'PWM8G1', 'PWM9G0', 'PWM9G1', 'QSPI1', 'QSPI2', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10G0', 'SALT10G1', 'SALT11G0', 'SALT11G1', 'SALT12G0', 'SALT12G1', 'SALT13G0', 'SALT13G1', 'SALT14G0', 'SALT14G1', 'SALT15G0', 'SALT15G1', 'SALT16G0', 'SALT16G1', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9G0', 'SALT9G1', 'SD1', 'SD2', 'SD3', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15
 ', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12G0', 'UART12G1', 'UART13G0', 'UART13G1', 'UART6', 'UART7', 'UART8', 'UART9', 'USBA', 'USBB', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: i3c2_default:function:0: 'I3C2' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', '
 NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2BH',
  'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: i3c2_default:groups:0: 'I3C2' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMCG1', 'EMMCG4', 'EMMCG8', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'HVI3C3', 'HVI3C4', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'N
 RI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10G0', 'PWM10G1', 'PWM11G0', 'PWM11G1', 'PWM12G0', 'PWM12G1', 'PWM13G0', 'PWM13G1', 'PWM14G0', 'PWM14G1', 'PWM15G0', 'PWM15G1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8G0', 'PWM8G1', 'PWM9G0', 'PWM9G1', 'QSPI1', 'QSPI2', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10G0', 'SALT10G1', 'SALT11G0', 'SALT11G1', 'SALT12G0', 'SALT12G1', 'SALT13G0', 'SALT13G1', 'SALT14G0', 'SALT14G1', 'SALT15G0', 'SALT15G1', 'SALT16G0', 'SALT16G1', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9G0', 'SALT9G1', 'SD1', 'SD2', 'SD3', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15
 ', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12G0', 'UART12G1', 'UART13G0', 'UART13G1', 'UART6', 'UART7', 'UART8', 'UART9', 'USBA', 'USBB', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: usb2ad_default:function:0: 'USB2AD' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', '
 NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 
 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: i3c2_default:function:0: 'I3C2' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS
 1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB
 2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: i3c2_default:groups:0: 'I3C2' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMCG1', 'EMMCG4', 'EMMCG8', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'HVI3C3', 'HVI3C4', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4
 ', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10G0', 'PWM10G1', 'PWM11G0', 'PWM11G1', 'PWM12G0', 'PWM12G1', 'PWM13G0', 'PWM13G1', 'PWM14G0', 'PWM14G1', 'PWM15G0', 'PWM15G1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8G0', 'PWM8G1', 'PWM9G0', 'PWM9G1', 'QSPI1', 'QSPI2', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10G0', 'SALT10G1', 'SALT11G0', 'SALT11G1', 'SALT12G0', 'SALT12G1', 'SALT13G0', 'SALT13G1', 'SALT14G0', 'SALT14G1', 'SALT15G0', 'SALT15G1', 'SALT16G0', 'SALT16G1', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9G0', 'SALT9G1', 'SD1', 'SD2', 'SD3', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'T
 ACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12G0', 'UART12G1', 'UART13G0', 'UART13G1', 'UART6', 'UART7', 'UART8', 'UART9', 'USBA', 'USBB', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: pinctrl: usb2ad_default:function:0: 'USB2AD' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1
 ', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB2BD', 'USB2
 BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: pinctrl: usb11bhid_default:function:0: 'USB11BHID' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMC', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NR
 I4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10', 'PWM11', 'PWM12', 'PWM13', 'PWM14', 'PWM15', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8', 'PWM9', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10', 'SALT11', 'SALT12', 'SALT13', 'SALT14', 'SALT15', 'SALT16', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9', 'SD1', 'SD2', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12', 'UART13', 'UART6', 'UART7', 'UART8', 'UART9', 'USBAD', 'USBADP', 'USB2AH', 'USB2AHP', 'USB
 2BD', 'USB2BH', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
	from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/syscon at 1e6e2000/smp-memram at 180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/syscon at 1e6e2000/interrupt-controller at 560: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic0']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/syscon at 1e6e2000/interrupt-controller at 570: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic1']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/display at 1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/xdma at 1e6e7000: failed to match any schema with compatible: ['aspeed,ast2600-xdma']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: adc at 1e6e9000: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: adc at 1e6e9100: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/syscon at 1e6e2000/smp-memram at 180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: crypto at 1e6fa000: 'aspeed,ahbc' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/syscon at 1e6e2000/interrupt-controller at 560: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic0']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/syscon at 1e6e2000/interrupt-controller at 570: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic1']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/video at 1e700000: failed to match any schema with compatible: ['aspeed,ast2600-video-engine']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: gpio at 1e780000: 'i2c3_mux_oe_n-hog', 'usb_power-hog' do not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,ast2400-gpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/display at 1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: sgpiom at 1e780500: '#interrupt-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/xdma at 1e6e7000: failed to match any schema with compatible: ['aspeed,ast2600-xdma']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: adc at 1e6e9000: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: sgpiom at 1e780600: '#interrupt-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: adc at 1e6e9100: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: crypto at 1e6fa000: 'aspeed,ahbc' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/timer at 1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/video at 1e700000: failed to match any schema with compatible: ['aspeed,ast2600-video-engine']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: gpio at 1e780000: 'usb_power-hog' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,ast2400-gpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: sgpiom at 1e780500: '#interrupt-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: sgpiom at 1e780600: '#interrupt-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: lpc at 1e789000: lpc-snoop at 80: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: lpc at 1e789000: reg-io-width: [[4]] is not of type 'object'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/timer at 1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: kcs at 24: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: kcs at 28: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: kcs at 2c: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: kcs at 114: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/lpc at 1e789000/lhc at a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: lpc at 1e789000: lpc-snoop at 80: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: lpc at 1e789000: reg-io-width: [[4]] is not of type 'object'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: kcs at 24: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/lpc at 1e789000/ibt at 140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: sdc at 1e740000: sdhci at 1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: sdc at 1e740000: sdhci at 1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: kcs at 28: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: kcs at 2c: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: kcs at 114: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/sdc at 1e740000/sdhci at 1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/sdc at 1e740000/sdhci at 1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/lpc at 1e789000/lhc at a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/lpc at 1e789000/ibt at 140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: sdc at 1e740000: sdhci at 1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: sdc at 1e740000: sdhci at 1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/sdc at 1e740000/sdhci at 1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/sdc at 1e740000/sdhci at 1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 200/pca9552 at 61: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 80/pca9552 at 62: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 280/i2c-mux at 70/i2c at 0/pca9551 at 60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 280/pca9552 at 65: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 280/i2c-mux at 70/i2c at 0/pca9551 at 62: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 300/i2c-mux at 70/i2c at 0/pca9551 at 60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 280/i2c-mux at 70/i2c at 1/pca9551 at 60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 300/i2c-mux at 70/i2c at 1/pca9551 at 61: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 280/i2c-mux at 70/i2c at 2/pca9551 at 61: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 300/pca9552 at 66: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 300/i2c-mux at 70/i2c at 0/pca9551 at 60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 300/i2c-mux at 70/i2c at 1/pca9551 at 61: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 30: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 300/i2c-mux at 70/i2c at 2/pca9551 at 62: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 300/i2c-mux at 70/i2c at 3/pca9551 at 63: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 31: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 380/i2c-mux at 70/i2c at 0/pca9551 at 60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 380/i2c-mux at 70/i2c at 1/pca9551 at 62: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 32: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 380/i2c-mux at 70/i2c at 2/pca9551 at 63: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 380/i2c-mux at 70/i2c at 3/pca9551 at 61: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 380/pca9552 at 65: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 33: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 31: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/max31785 at 52: failed to match any schema with compatible: ['maxim,max31785a']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9551 at 60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 61: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 32: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: dps310 at 76: '#io-channel-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/trivial-devices.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 33: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 480/pca9552 at 60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 480/pca9552 at 61: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 30: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 600/i2c-mux at 70/i2c at 0/pca9551 at 60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 34: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 700/pca9552 at 60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 400/pca9552 at 35: failed to match any schema with compatible: ['ibm,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 780/pca9552 at 60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 800/pca9552 at 60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: fsi at 1e79b000: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: fsi at 1e79b000: Unevaluated properties are not allowed ('#interrupt-cells', 'compatible', 'interrupt-controller' were unexpected)
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/fsi at 1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 780/i2c-mux at 70/i2c at 2/pca9551 at 60: failed to match any schema with compatible: ['nxp,pca9551']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 780/i2c-mux at 70/i2c at 3/max31785 at 52: failed to match any schema with compatible: ['maxim,max31785a']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 780/i2c-mux at 70/i2c at 3/pca9552 at 60: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/bus at 1e78a000/i2c-bus at 780/i2c-mux at 70/i2c at 3/pca9552 at 61: failed to match any schema with compatible: ['nxp,pca9552']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: fsi at 1e79b000: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: fsi at 1e79b000: Unevaluated properties are not allowed ('#interrupt-cells', 'compatible', 'interrupt-controller' were unexpected)
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/fsi at 1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: fsi at 1e79b100: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/fsi at 1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dtb: /ahb/apb/dma-controller at 1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: fsi at 1e79b100: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/fsi at 1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dtb: /ahb/apb/dma-controller at 1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']