[PATCH v8 08/22] pinctrl: starfive: Add StarFive JHB100 sys1 controller driver

[Changhuang Liang <changhuang.liang@starfivetech.com>]

Add pinctrl driver for StarFive JHB100 SoC System-1(sys1) pinctrl
controller.

Co-developed-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Lianfeng Ouyang <lianfeng.ouyang@starfivetech.com>
Signed-off-by: Alex Soo <yuklin.soo@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
---
 drivers/pinctrl/starfive/Kconfig              | 11 +++
 drivers/pinctrl/starfive/Makefile             |  1 +
 .../starfive/pinctrl-starfive-jhb100-sys1.c   | 94 +++++++++++++++++++
 3 files changed, 106 insertions(+)
 create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys1.c

diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index 992238f5b49d..895b9cb0cb2a 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -77,3 +77,14 @@ config PINCTRL_STARFIVE_JHB100_SYS0H
 	  This also provides an interface to the GPIO pins not used by other
 	  peripherals supporting inputs, outputs, configuring pull-up/pull-down
 	  and interrupts on input changes.
+
+config PINCTRL_STARFIVE_JHB100_SYS1
+	tristate "StarFive JHB100 SoC System-1 pinctrl and GPIO driver"
+	depends on ARCH_STARFIVE || COMPILE_TEST
+	select PINCTRL_STARFIVE_JHB100
+	default ARCH_STARFIVE
+	help
+	  Say yes here to support System-1 pin control on the StarFive JHB100 SoC.
+	  This also provides an interface to the GPIO pins not used by other
+	  peripherals supporting inputs, outputs, configuring pull-up/pull-down
+	  and interrupts on input changes.
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index b26156a6d0eb..8d96cf80d377 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON)	+= pinctrl-starfive-jh7110-aon.o
 obj-$(CONFIG_PINCTRL_STARFIVE_JHB100)		+= pinctrl-starfive-jhb100.o
 obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0)	+= pinctrl-starfive-jhb100-sys0.o
 obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H)	+= pinctrl-starfive-jhb100-sys0h.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS1)	+= pinctrl-starfive-jhb100-sys1.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys1.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys1.c
new file mode 100644
index 000000000000..2185c3d15bc2
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-sys1.c
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC System-1 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+/* sys1 pad numbers */
+#define PADNUM_SYS1_GPIO_A22				6
+#define PADNUM_SYS1_GPIO_A23				7
+
+static const struct jhb100_pin_layout_desc jhb100_sys1_pl_desc[] = {
+	{ .pin_start = 0, .pin_cnt = 7, .name = "gpio", .gpio_func_sel = 0 },
+	{ .pin_start = 7, .pin_cnt = 1, .name = "espi1_reset", .gpio_func_sel = 1 },
+	{ 0xff },
+};
+
+static const struct config_reg_layout_desc jhb100_sys1_pinctrl_rl_desc[] = {
+	{
+		.pin_start					= 0,
+		.pin_cnt					= 8,
+		.fields[PAD_CFG_DRIVE_STRENGTH_2BIT]		= { .shift = 0, .width = 2 },
+		.fields[PAD_CFG_INPUT_ENABLE]			= { .shift = 2, .width = 1 },
+		.fields[PAD_CFG_PULL_DOWN]			= { .shift = 3, .width = 1 },
+		.fields[PAD_CFG_PULL_UP]			= { .shift = 4, .width = 1 },
+		.fields[PAD_CFG_SLEW_RATE]			= { .shift = 5, .width = 1 },
+		.fields[PAD_CFG_SCHMITT_TRIGGER_SELECT]		= { .shift = 6, .width = 1 },
+		.fields[PAD_CFG_DEBOUNCE_WIDTH]			= { .shift = 15, .width = 17 },
+	},
+	{ 0xff },
+};
+
+static const struct starfive_pinctrl_regs jhb100_sys1_pinctrl_regs = {
+	.func_sel		= { .reg = 0x30, .width_per_pin = 2 },
+	.config			= 0x04,
+	.output			= 0x24,
+	.output_en		= 0x28,
+	.gpio_status		= 0x2c,
+	.irq_en			= 0x34,
+	.irq_status		= 0x38,
+	.irq_clr		= 0x3c,
+	.irq_trigger		= 0x40,
+	.irq_level		= 0x44,
+	.irq_both_edge		= 0x48,
+	.irq_edge		= 0x4c,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_sys1[] = {
+	{ .func = "espi",		.val = 1 },
+	{ .func = "espi_reset",		.val = 0 },
+	{ .func = "gpio",		.val = 0,
+	  .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_SYS1_GPIO_A22) },
+	{ .func = "gpio",		.val = 1,
+	  .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_SYS1_GPIO_A23) },
+	{ .func = "host0_port80",	.val = 2 },
+	{ .func = "host1_port80",	.val = 3 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_sys1_pinctrl_info = {
+	.name			= "jhb100-sys1",
+	.pl_desc		= jhb100_sys1_pl_desc,
+	.crl_desc		= jhb100_sys1_pinctrl_rl_desc,
+	.regs			= &jhb100_sys1_pinctrl_regs,
+	.fmaps			= jhb100_func_maps_sys1,
+	.num_maps		= ARRAY_SIZE(jhb100_func_maps_sys1),
+};
+
+static const struct of_device_id jhb100_sys1_pinctrl_of_match[] = {
+	{
+		.compatible = "starfive,jhb100-sys1-pinctrl",
+		.data = &jhb100_sys1_pinctrl_info,
+	},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_sys1_pinctrl_of_match);
+
+static struct platform_driver jhb100_sys1_pinctrl_driver = {
+	.probe = jhb100_pinctrl_probe,
+	.driver = {
+		.name = "starfive-jhb100-sys1-pinctrl",
+		.of_match_table = jhb100_sys1_pinctrl_of_match,
+	},
+};
+module_platform_driver(jhb100_sys1_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC System-1 domain");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL");
-- 
2.25.1