* [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG @ 2026-09-10 14:47 Eric Lin 2026-09-11 9:53 ` Mathias Nyman 0 siblings, 1 reply; 11+ messages in thread From: Eric Lin @ 2026-09-10 14:47 UTC (permalink / raw) To: mathias.nyman; +Cc: gregkh, linux-usb Hi! I am experiencing an issue where my internal USB fingerprint sensor enters a continuous reset loop on Linux System Info: Laptop Model: MSI Prestige 16 Flip AI+ C3MTG Device info: Bus 003 Device 002: ID 27c6:6090 Shenzhen Goodix Technology Co.,Ltd. Goodix USB2.0 MISC Kernel Version: 7.3.0-rc2-1-cachyos-rc Linux Distro: Arch Linux Behavior: The device repeatedly disconnects and reconnects. I have tried disabling USB autosuspend via udev rules, but the reset behavior continues Relevant dmesg log output: [ 0.728290] usb 3-6: new full-speed USB device number 2 using xhci_hcd [ 0.852232] usb 3-6: New USB device found, idVendor=27c6, idProduct=6090, bcdDevice= 1.00 [ 0.853030] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 0.853035] usb 3-6: Product: Goodix USB2.0 MISC [ 0.853038] usb 3-6: Manufacturer: Goodix Technology Co., Ltd. [ 0.853041] usb 3-6: SerialNumber: UIDEA968203_XXXX_MOC_B0 [ 10.774839] ucsi_acpi USBC000:00: GET_CURRENT_CAM command failed [ 30.365584] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 30.605812] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 425.108819] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 425.368738] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 1265.198999] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 1265.447057] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 1283.745362] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 1491.845657] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 1492.094664] usb 3-6: reset full-speed USB device number 2 using xhci_hcd Please let me know if you need any further hardware traces or if I should test a specific kernel patch. Best regards, Eric ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-10 14:47 [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG Eric Lin @ 2026-09-11 9:53 ` Mathias Nyman 2026-09-11 12:11 ` EricLin 0 siblings, 1 reply; 11+ messages in thread From: Mathias Nyman @ 2026-09-11 9:53 UTC (permalink / raw) To: Eric Lin, mathias.nyman; +Cc: gregkh, linux-usb Hi On 9/10/26 17:47, Eric Lin wrote: > Hi! I am experiencing an issue where my internal USB fingerprint > sensor enters a continuous reset loop on Linux > > System Info: > Laptop Model: MSI Prestige 16 Flip AI+ C3MTG > Device info: Bus 003 Device 002: ID 27c6:6090 Shenzhen Goodix > Technology Co.,Ltd. Goodix USB2.0 MISC > Kernel Version: 7.3.0-rc2-1-cachyos-rc > Linux Distro: Arch Linux Is this a new issue with 7.3-rc kernel, or something that can be reproduced with older kernels? > > Behavior: > The device repeatedly disconnects and reconnects. I have tried > disabling USB autosuspend via udev rules, but the reset behavior > continues > > Relevant dmesg log output: > [ 0.728290] usb 3-6: new full-speed USB device number 2 using xhci_hcd > [ 0.852232] usb 3-6: New USB device found, idVendor=27c6, > idProduct=6090, bcdDevice= 1.00 > [ 0.853030] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 > [ 0.853035] usb 3-6: Product: Goodix USB2.0 MISC > [ 0.853038] usb 3-6: Manufacturer: Goodix Technology Co., Ltd. > [ 0.853041] usb 3-6: SerialNumber: UIDEA968203_XXXX_MOC_B0 > [ 10.774839] ucsi_acpi USBC000:00: GET_CURRENT_CAM command failed > [ 30.365584] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > [ 30.605812] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > [ 425.108819] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > [ 425.368738] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > [ 1265.198999] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > [ 1265.447057] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > [ 1283.745362] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > [ 1491.845657] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > [ 1492.094664] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > Those resets are not that frequent, often several minutes apart. First guess is that its still somehow related to power management, and device is reset (in resume?) to recover. > Please let me know if you need any further hardware traces or if I > should test a specific kernel patch. If it works on newer kernels then git bisect can help you find the offending commit. Enabling usb core and xhci dynamic debug could tell us more: echo 'module xhci_hcd =p' >/sys/kernel/debug/dynamic_debug/control echo 'module usbcore =p' >/sys/kernel/debug/dynamic_debug/control < Reproduce issue > Send output of dmesg Thanks Mathias ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-11 9:53 ` Mathias Nyman @ 2026-09-11 12:11 ` EricLin 2026-09-11 13:39 ` Mathias Nyman 0 siblings, 1 reply; 11+ messages in thread From: EricLin @ 2026-09-11 12:11 UTC (permalink / raw) To: mathias.nyman; +Cc: ericlin050914, gregkh, linux-usb, mathias.nyman > Is this a new issue with 7.3-rc kernel, or something that can be reproduced with older kernels? This issue has persisted since I performed a fresh installation of Arch Linux on this device (which is Linux kernel 7.0) > Those resets are not that frequent, often several minutes apart. > > First guess is that its still somehow related to power management, and device is reset (in resume?) to recover. Well, these messages seem to appear only when I use this fingerprint sensor > If it works on newer kernels then git bisect can help you find the offending commit. > Enabling usb core and xhci dynamic debug could tell us more: > echo 'module xhci_hcd =p' >/sys/kernel/debug/dynamic_debug/control > echo 'module usbcore =p' >/sys/kernel/debug/dynamic_debug/control > < Reproduce issue > > Send output of dmesg Here are the outputs of dmesg (with debug enabled) [ 0.467820] xhci_hcd 0000:00:0d.0: xHCI Host Controller [ 0.467827] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 1 [ 0.468960] xhci_hcd 0000:00:0d.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 [ 0.469267] xhci_hcd 0000:00:0d.0: xHCI Host Controller [ 0.469269] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 2 [ 0.469270] xhci_hcd 0000:00:0d.0: Host supports USB 3.2 Enhanced SuperSpeed [ 0.471205] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.471208] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 [ 0.472349] xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 [ 0.472638] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.472639] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 [ 0.472640] xhci_hcd 0000:00:14.0: Host supports USB 3.2 Enhanced SuperSpeed [ 0.717291] usb 3-6: new full-speed USB device number 2 using xhci_hcd [ 0.840784] usb 3-6: New USB device found, idVendor=27c6, idProduct=6090, bcdDevice= 1.00 [ 0.841565] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 0.841569] usb 3-6: Product: Goodix USB2.0 MISC [ 0.841572] usb 3-6: Manufacturer: Goodix Technology Co., Ltd. [ 0.841574] usb 3-6: SerialNumber: UIDEA968203_XXXX_MOC_B0 [ 0.957240] usb 3-7: new high-speed USB device number 3 using xhci_hcd [ 197.151533] usb 3-6: reset full-speed USB device number 2 using xhci_hcd # The first time of using this fingerprint sensor [ 197.401517] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 240.364042] xhci_hcd 0000:00:14.0: HC state intact, continuing without reset # The second time of using this fingerprint sensor [ 240.364098] xhci_hcd 0000:00:14.0: Setting command ring address to 0xffffe001 [ 240.364262] xhci_hcd 0000:00:14.0: xhci_resume: starting usb3 port polling. [ 240.364267] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb4 port polling [ 240.364278] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling [ 240.364280] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0 [ 240.364344] xhci_hcd 0000:00:14.0: Get port status 3-1 read: 0x2a0, return 0x100 [ 240.364407] xhci_hcd 0000:00:14.0: Get port status 3-2 read: 0x2a0, return 0x100 [ 240.364418] xhci_hcd 0000:00:14.0: Get port status 3-3 read: 0x2a0, return 0x100 [ 240.364443] xhci_hcd 0000:00:14.0: Get port status 3-4 read: 0x2a0, return 0x100 [ 240.364468] xhci_hcd 0000:00:14.0: Get port status 3-5 read: 0x2a0, return 0x100 [ 240.364473] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x663, return 0x107 [ 240.364500] xhci_hcd 0000:00:14.0: Get port status 3-7 read: 0xe63, return 0x507 [ 240.364526] xhci_hcd 0000:00:14.0: Get port status 3-8 read: 0x2a0, return 0x100 [ 240.364531] xhci_hcd 0000:00:14.0: Get port status 3-9 read: 0x2a0, return 0x100 [ 240.364537] xhci_hcd 0000:00:14.0: Get port status 3-10 read: 0x2a0, return 0x100 [ 240.364564] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x663, return 0x107 [ 240.364611] xhci_hcd 0000:00:14.0: clear USB_PORT_FEAT_SUSPEND [ 240.364612] xhci_hcd 0000:00:14.0: PORTSC 0663 [ 240.364616] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x663, write 0x107e1 [ 240.405029] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x7e3, write 0x10601 [ 240.405066] usb 3-6: usb auto-resume [ 240.405138] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x400603 [ 240.405148] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 240.446041] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x603, return 0x40103 [ 240.446119] xhci_hcd 0000:00:14.0: clear port6 suspend/resume change, portsc: 0x603 [ 240.456987] usb 3-6: finish resume [ 240.457379] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 [ 240.511402] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 240.511413] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 240.517961] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 240.518038] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 240.568969] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 240.568998] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.569335] xhci_hcd 0000:00:14.0: Completed reset device command. [ 240.569436] xhci_hcd 0000:00:14.0: Successful reset device command. [ 240.569550] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 240.569556] xhci_hcd 0000:00:14.0: Slot already in default state [ 240.569822] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 240.570131] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 [ 240.605942] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling [ 240.624155] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 240.624165] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 240.630984] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 240.631050] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 240.682009] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 240.682037] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.682206] xhci_hcd 0000:00:14.0: Completed reset device command. [ 240.682309] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state [ 240.682316] xhci_hcd 0000:00:14.0: Not freeing device rings. [ 240.682352] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.682578] xhci_hcd 0000:00:14.0: Successful setup address command [ 240.682633] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x000000fffff000 [ 240.682637] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @0000000021fab8ba = 0x000000fffd7000 [ 240.682642] xhci_hcd 0000:00:14.0: Output Context DMA address = 0xfffd7000 [ 240.682644] xhci_hcd 0000:00:14.0: Internal device address = 1 [ 240.693858] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 240.693930] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x80 [ 240.693941] xhci_hcd 0000:00:14.0: add ep 0x1, slot id 1, new drop flags = 0x0, new add flags = 0x84 [ 240.693945] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000dd219587 [ 240.693951] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.694317] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command [ 240.694634] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.694762] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6 [ 240.694779] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.695003] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.695040] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1 [ 240.695064] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.695313] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x603, return 0x103 [ 240.695616] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 240.705786] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 [ 240.759625] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 240.759638] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 240.766960] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 240.767032] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 240.817914] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 240.817926] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.818251] xhci_hcd 0000:00:14.0: Completed reset device command. [ 240.818348] xhci_hcd 0000:00:14.0: Successful reset device command. [ 240.818446] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 240.818452] xhci_hcd 0000:00:14.0: Slot already in default state [ 240.818685] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 240.818774] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 [ 240.853852] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling [ 240.872609] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 240.872620] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 240.878941] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 240.879016] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 240.930917] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 240.930930] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.931094] xhci_hcd 0000:00:14.0: Completed reset device command. [ 240.931198] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state [ 240.931205] xhci_hcd 0000:00:14.0: Not freeing device rings. [ 240.931220] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.931500] xhci_hcd 0000:00:14.0: Successful setup address command [ 240.931542] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x000000fffff000 [ 240.931547] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @0000000021fab8ba = 0x000000fffd7000 [ 240.931552] xhci_hcd 0000:00:14.0: Output Context DMA address = 0xfffd7000 [ 240.931554] xhci_hcd 0000:00:14.0: Internal device address = 1 [ 240.943853] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 240.943921] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x80 [ 240.943931] xhci_hcd 0000:00:14.0: add ep 0x1, slot id 1, new drop flags = 0x0, new add flags = 0x84 [ 240.943936] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000dd219587 [ 240.943941] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.944257] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command [ 240.944602] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.944652] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6 [ 240.944680] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.944870] xhci_hcd 0000:00:14.0: // Ding dong! [ 240.944908] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1 [ 240.944916] xhci_hcd 0000:00:14.0: // Ding dong! [ 241.109911] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling [ 243.707621] xhci_hcd 0000:00:14.0: // Ding dong! [ 243.707776] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6 [ 243.707787] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1 [ 243.707791] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 0 [ 243.707934] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x603, write 0x10661 [ 243.719855] usb 3-6: usb auto-suspend, wakeup 0 [ 243.730866] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling [ 243.730894] xhci_hcd 0000:00:14.0: config port 4-1 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730899] xhci_hcd 0000:00:14.0: config port 4-2 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730903] xhci_hcd 0000:00:14.0: config port 3-1 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730907] xhci_hcd 0000:00:14.0: config port 3-2 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730910] xhci_hcd 0000:00:14.0: config port 3-3 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730913] xhci_hcd 0000:00:14.0: config port 3-4 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730916] xhci_hcd 0000:00:14.0: config port 3-5 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730920] xhci_hcd 0000:00:14.0: config port 3-8 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730923] xhci_hcd 0000:00:14.0: config port 3-9 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730926] xhci_hcd 0000:00:14.0: config port 3-10 wake bits, portsc: 0xa0002a0, write: 0xa0202a0 [ 243.730928] xhci_hcd 0000:00:14.0: xhci_suspend: stopping usb3 port polling. [ 243.730936] xhci_hcd 0000:00:14.0: Setting command ring address to 0xffffe001 [ 243.731073] xhci_hcd 0000:00:14.0: hcd_pci_runtime_suspend: 0 [ 590.653758] xhci_hcd 0000:00:14.0: HC state intact, continuing without reset # The third time of using this fingerprint sensor [ 590.653792] xhci_hcd 0000:00:14.0: Setting command ring address to 0xffffe001 [ 590.653954] xhci_hcd 0000:00:14.0: xhci_resume: starting usb3 port polling. [ 590.653959] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb4 port polling [ 590.653969] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling [ 590.653971] xhci_hcd 0000:00:14.0: hcd_pci_runtime_resume: 0 [ 590.654004] xhci_hcd 0000:00:14.0: Get port status 3-1 read: 0x2a0, return 0x100 [ 590.654029] xhci_hcd 0000:00:14.0: Get port status 3-2 read: 0x2a0, return 0x100 [ 590.654041] xhci_hcd 0000:00:14.0: Get port status 3-3 read: 0x2a0, return 0x100 [ 590.654052] xhci_hcd 0000:00:14.0: Get port status 3-4 read: 0x2a0, return 0x100 [ 590.654059] xhci_hcd 0000:00:14.0: Get port status 3-5 read: 0x2a0, return 0x100 [ 590.654065] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x663, return 0x107 [ 590.654077] xhci_hcd 0000:00:14.0: Get port status 3-7 read: 0xe63, return 0x507 [ 590.654088] xhci_hcd 0000:00:14.0: Get port status 3-8 read: 0x2a0, return 0x100 [ 590.654094] xhci_hcd 0000:00:14.0: Get port status 3-9 read: 0x2a0, return 0x100 [ 590.654100] xhci_hcd 0000:00:14.0: Get port status 3-10 read: 0x2a0, return 0x100 [ 590.654130] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x663, return 0x107 [ 590.654141] xhci_hcd 0000:00:14.0: clear USB_PORT_FEAT_SUSPEND [ 590.654142] xhci_hcd 0000:00:14.0: PORTSC 0663 [ 590.654145] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x663, write 0x107e1 [ 590.694874] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x7e3, write 0x10601 [ 590.694893] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x400603 [ 590.694899] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 590.694957] usb 3-6: usb auto-resume [ 590.735791] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x603, return 0x40103 [ 590.735858] xhci_hcd 0000:00:14.0: clear port6 suspend/resume change, portsc: 0x603 [ 590.747785] usb 3-6: finish resume [ 590.748300] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x603, return 0x103 [ 590.748381] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 [ 590.802405] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 590.802416] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 590.808744] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 590.808812] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 590.841739] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling [ 590.859876] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 590.859888] xhci_hcd 0000:00:14.0: // Ding dong! [ 590.860243] xhci_hcd 0000:00:14.0: Completed reset device command. [ 590.860288] xhci_hcd 0000:00:14.0: Successful reset device command. [ 590.860389] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 590.860393] xhci_hcd 0000:00:14.0: Slot already in default state [ 590.860528] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 590.860677] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 [ 590.914691] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 590.914704] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 590.921816] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 590.921890] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 590.972820] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 590.972840] xhci_hcd 0000:00:14.0: // Ding dong! [ 590.972927] xhci_hcd 0000:00:14.0: Completed reset device command. [ 590.972957] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state [ 590.972959] xhci_hcd 0000:00:14.0: Not freeing device rings. [ 590.972982] xhci_hcd 0000:00:14.0: // Ding dong! [ 590.973077] xhci_hcd 0000:00:14.0: Successful setup address command [ 590.973099] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x000000fffff000 [ 590.973103] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @0000000021fab8ba = 0x000000fffd7000 [ 590.973108] xhci_hcd 0000:00:14.0: Output Context DMA address = 0xfffd7000 [ 590.973110] xhci_hcd 0000:00:14.0: Internal device address = 1 [ 590.984557] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 590.984681] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x80 [ 590.984688] xhci_hcd 0000:00:14.0: add ep 0x1, slot id 1, new drop flags = 0x0, new add flags = 0x84 [ 590.984691] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000dd219587 [ 590.984698] xhci_hcd 0000:00:14.0: // Ding dong! [ 590.985041] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command [ 590.985286] xhci_hcd 0000:00:14.0: // Ding dong! [ 590.985342] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6 [ 590.985370] xhci_hcd 0000:00:14.0: // Ding dong! [ 590.985541] xhci_hcd 0000:00:14.0: // Ding dong! [ 590.985603] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1 [ 590.985612] xhci_hcd 0000:00:14.0: // Ding dong! [ 590.986371] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 591.009222] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 [ 591.064173] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 591.064184] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 591.069758] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 591.069829] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 591.097722] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling [ 591.120775] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 591.120787] xhci_hcd 0000:00:14.0: // Ding dong! [ 591.121111] xhci_hcd 0000:00:14.0: Completed reset device command. [ 591.121136] xhci_hcd 0000:00:14.0: Successful reset device command. [ 591.121242] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 591.121247] xhci_hcd 0000:00:14.0: Slot already in default state [ 591.121381] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 591.121480] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 [ 591.175511] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 591.175522] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 591.181795] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 591.181865] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 591.232780] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 591.232792] xhci_hcd 0000:00:14.0: // Ding dong! [ 591.232840] xhci_hcd 0000:00:14.0: Completed reset device command. [ 591.232852] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state [ 591.232854] xhci_hcd 0000:00:14.0: Not freeing device rings. [ 591.232865] xhci_hcd 0000:00:14.0: // Ding dong! [ 591.232981] xhci_hcd 0000:00:14.0: Successful setup address command [ 591.233001] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x000000fffff000 [ 591.233005] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @0000000021fab8ba = 0x000000fffd7000 [ 591.233008] xhci_hcd 0000:00:14.0: Output Context DMA address = 0xfffd7000 [ 591.233010] xhci_hcd 0000:00:14.0: Internal device address = 1 [ 591.244582] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 591.244665] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x80 [ 591.244672] xhci_hcd 0000:00:14.0: add ep 0x1, slot id 1, new drop flags = 0x0, new add flags = 0x84 [ 591.244674] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000dd219587 [ 591.244681] xhci_hcd 0000:00:14.0: // Ding dong! [ 591.245049] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command [ 591.245301] xhci_hcd 0000:00:14.0: // Ding dong! [ 591.245354] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6 [ 591.245380] xhci_hcd 0000:00:14.0: // Ding dong! [ 591.245580] xhci_hcd 0000:00:14.0: // Ding dong! [ 591.245743] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1 [ 591.245769] xhci_hcd 0000:00:14.0: // Ding dong! [ 591.345699] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling Best regards, Eric ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-11 12:11 ` EricLin @ 2026-09-11 13:39 ` Mathias Nyman 2026-09-11 14:48 ` EricLin 0 siblings, 1 reply; 11+ messages in thread From: Mathias Nyman @ 2026-09-11 13:39 UTC (permalink / raw) To: EricLin; +Cc: gregkh, linux-usb, mathias.nyman On 9/11/26 15:11, EricLin wrote: >> Is this a new issue with 7.3-rc kernel, or something that can be > reproduced with older kernels? > > This issue has persisted since I performed a fresh installation of Arch Linux on this device (which is Linux kernel 7.0) > >> Those resets are not that frequent, often several minutes apart. >> >> First guess is that its still somehow related to power management, and device > is reset (in resume?) to recover. > > Well, these messages seem to appear only when I use this fingerprint sensor > >> If it works on newer kernels then git bisect can help you find the offending > commit. > >> Enabling usb core and xhci dynamic debug could tell us more: > >> echo 'module xhci_hcd =p' >/sys/kernel/debug/dynamic_debug/control >> echo 'module usbcore =p' >/sys/kernel/debug/dynamic_debug/control >> < Reproduce issue > >> Send output of dmesg > > Here are the outputs of dmesg (with debug enabled) > [ 0.467820] xhci_hcd 0000:00:0d.0: xHCI Host Controller > [ 0.467827] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 1 > [ 0.468960] xhci_hcd 0000:00:0d.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 > [ 0.469267] xhci_hcd 0000:00:0d.0: xHCI Host Controller > [ 0.469269] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 2 > [ 0.469270] xhci_hcd 0000:00:0d.0: Host supports USB 3.2 Enhanced SuperSpeed > [ 0.471205] xhci_hcd 0000:00:14.0: xHCI Host Controller > [ 0.471208] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 > [ 0.472349] xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 > [ 0.472638] xhci_hcd 0000:00:14.0: xHCI Host Controller > [ 0.472639] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 > [ 0.472640] xhci_hcd 0000:00:14.0: Host supports USB 3.2 Enhanced SuperSpeed > [ 0.717291] usb 3-6: new full-speed USB device number 2 using xhci_hcd > [ 0.840784] usb 3-6: New USB device found, idVendor=27c6, idProduct=6090, bcdDevice= 1.00 > [ 0.841565] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 > [ 0.841569] usb 3-6: Product: Goodix USB2.0 MISC > [ 0.841572] usb 3-6: Manufacturer: Goodix Technology Co., Ltd. > [ 0.841574] usb 3-6: SerialNumber: UIDEA968203_XXXX_MOC_B0 > [ 0.957240] usb 3-7: new high-speed USB device number 3 using xhci_hcd > [ 197.151533] usb 3-6: reset full-speed USB device number 2 using xhci_hcd # The first time of using this fingerprint sensor > [ 197.401517] usb 3-6: reset full-speed USB device number 2 using xhci_hcd > [ 240.364042] xhci_hcd 0000:00:14.0: HC state intact, continuing without reset # The second time of using this fingerprint sensor > [ 240.364098] xhci_hcd 0000:00:14.0: Setting command ring address to 0xffffe001 > [ 240.364262] xhci_hcd 0000:00:14.0: xhci_resume: starting usb3 port polling. Ok, looks like xHC (and fingerprint sensor) were suspended, and sensor reset at resume. Does disabling runtime suspend for xHCI and the sensor help? After boot, as root: echo on > /sys/bus/pci/devices/0000:00:14.0/power/control echo on > /sys/bus/usb/devices/3-6/power/control Thanks Mathias ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-11 13:39 ` Mathias Nyman @ 2026-09-11 14:48 ` EricLin 2026-09-11 20:21 ` Michal Pecio 0 siblings, 1 reply; 11+ messages in thread From: EricLin @ 2026-09-11 14:48 UTC (permalink / raw) To: mathias.nyman; +Cc: ericlin050914, gregkh, linux-usb, mathias.nyman > Ok, looks like xHC (and fingerprint sensor) were suspended, and sensor reset > at resume. > Does disabling runtime suspend for xHCI and the sensor help? > After boot, as root: > echo on > /sys/bus/pci/devices/0000:00:14.0/power/control > echo on > /sys/bus/usb/devices/3-6/power/control Sadly, These command doesn't work [ 0.481019] xhci_hcd 0000:00:0d.0: xHCI Host Controller [ 0.481023] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 1 [ 0.482157] xhci_hcd 0000:00:0d.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 [ 0.482447] xhci_hcd 0000:00:0d.0: xHCI Host Controller [ 0.482451] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 2 [ 0.482453] xhci_hcd 0000:00:0d.0: Host supports USB 3.2 Enhanced SuperSpeed [ 0.484361] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.484363] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 [ 0.485511] xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 [ 0.485793] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.485795] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 [ 0.485796] xhci_hcd 0000:00:14.0: Host supports USB 3.2 Enhanced SuperSpeed [ 0.725275] usb 3-6: new full-speed USB device number 2 using xhci_hcd [ 0.849356] usb 3-6: New USB device found, idVendor=27c6, idProduct=6090, bcdDevice= 1.00 [ 0.850388] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 0.850393] usb 3-6: Product: Goodix USB2.0 MISC [ 0.850396] usb 3-6: Manufacturer: Goodix Technology Co., Ltd. [ 0.850399] usb 3-6: SerialNumber: UIDEA968203_XXXX_MOC_B0 [ 0.965230] usb 3-7: new high-speed USB device number 3 using xhci_hcd [ 26.846586] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 27.088643] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 44.120047] usb 3-6: reset full-speed USB device number 2 using xhci_hcd # Disabled runtime suspend for xHCI and the sensor [ 55.557350] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 81.929983] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 # Enabled debug [ 81.983851] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 81.983866] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 81.991791] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 81.991845] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 82.042778] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 82.042793] xhci_hcd 0000:00:14.0: // Ding dong! [ 82.043072] xhci_hcd 0000:00:14.0: Completed reset device command. [ 82.043193] xhci_hcd 0000:00:14.0: Successful reset device command. [ 82.043344] usb 3-6: reset full-speed USB device number 2 using xhci_hcd [ 82.043351] xhci_hcd 0000:00:14.0: Slot already in default state [ 82.043518] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 82.043572] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 [ 82.066750] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling [ 82.097440] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x200603 [ 82.097453] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 82.103779] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x200603, return 0x100103 [ 82.103820] xhci_hcd 0000:00:14.0: clear port6 reset change, portsc: 0x603 [ 82.154786] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1 [ 82.154800] xhci_hcd 0000:00:14.0: // Ding dong! [ 82.154942] xhci_hcd 0000:00:14.0: Completed reset device command. [ 82.155025] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state [ 82.155033] xhci_hcd 0000:00:14.0: Not freeing device rings. [ 82.155052] xhci_hcd 0000:00:14.0: // Ding dong! [ 82.155268] xhci_hcd 0000:00:14.0: Successful setup address command [ 82.155279] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x000000fffff000 [ 82.155284] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @00000000c504d3ce = 0x000000fffd7000 [ 82.155290] xhci_hcd 0000:00:14.0: Output Context DMA address = 0xfffd7000 [ 82.155293] xhci_hcd 0000:00:14.0: Internal device address = 1 [ 82.166500] xhci_hcd 0000:00:14.0: Waiting for status stage event [ 82.166625] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x80 [ 82.166651] xhci_hcd 0000:00:14.0: add ep 0x1, slot id 1, new drop flags = 0x0, new add flags = 0x84 [ 82.166656] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000d584fa66 [ 82.166665] xhci_hcd 0000:00:14.0: // Ding dong! [ 82.166961] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command [ 82.167272] xhci_hcd 0000:00:14.0: // Ding dong! [ 82.167388] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6 [ 82.167412] xhci_hcd 0000:00:14.0: // Ding dong! [ 82.167646] xhci_hcd 0000:00:14.0: // Ding dong! [ 82.167672] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 1 [ 82.167720] xhci_hcd 0000:00:14.0: // Ding dong! [ 82.314749] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb3 port polling ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-11 14:48 ` EricLin @ 2026-09-11 20:21 ` Michal Pecio 2026-09-16 13:17 ` EricLin 0 siblings, 1 reply; 11+ messages in thread From: Michal Pecio @ 2026-09-11 20:21 UTC (permalink / raw) To: EricLin; +Cc: mathias.nyman, gregkh, linux-usb, mathias.nyman On Fri, 11 Sep 2026 22:48:41 +0800, EricLin wrote: > > echo on > /sys/bus/pci/devices/0000:00:14.0/power/control > > echo on > /sys/bus/usb/devices/3-6/power/control > > Sadly, These command doesn't work Hi, Your log looks like they work - nothing is being suspended anymore ;) Do you have any idea what kernel driver (try lsusb -tv) or userspace software is using this device? It's quite possible that the driver simply requests a reset explicitly, either as a matter of routine or to recover from some problems. Regards, Michal ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-11 20:21 ` Michal Pecio @ 2026-09-16 13:17 ` EricLin 2026-09-16 17:47 ` Michal Pecio 0 siblings, 1 reply; 11+ messages in thread From: EricLin @ 2026-09-16 13:17 UTC (permalink / raw) To: michal.pecio Cc: ericlin050914, gregkh, linux-usb, mathias.nyman, mathias.nyman Sorry for the late reply > Hi, > Your log looks like they work - nothing is being suspended anymore ;) > Do you have any idea what kernel driver (try lsusb -tv) or userspace > software is using this device? It's quite possible that the driver > simply requests a reset explicitly, either as a matter of routine or > to recover from some problems. I'm using fprint to operate this fingerprint sensor Here are the outputs of lsusb -tv /: Bus 001.Port 001: Dev 001, Class=root_hub, Driver=xhci_hcd/1p, 480M ID 1d6b:0002 Linux Foundation 2.0 root hub /: Bus 002.Port 001: Dev 001, Class=root_hub, Driver=xhci_hcd/4p, 20000M/x2 ID 1d6b:0003 Linux Foundation 3.0 root hub /: Bus 003.Port 001: Dev 001, Class=root_hub, Driver=xhci_hcd/10p, 480M ID 1d6b:0002 Linux Foundation 2.0 root hub |__ Port 006: Dev 002, If 0, Class=Vendor Specific Class, Driver=[none], 12M ID 27c6:6090 Shenzhen Goodix Technology Co.,Ltd. |__ Port 007: Dev 003, If 0, Class=Video, Driver=uvcvideo, 480M ID 5986:11cc Bison Electronics Inc. |__ Port 007: Dev 003, If 1, Class=Video, Driver=uvcvideo, 480M ID 5986:11cc Bison Electronics Inc. |__ Port 007: Dev 003, If 2, Class=Video, Driver=uvcvideo, 480M ID 5986:11cc Bison Electronics Inc. |__ Port 007: Dev 003, If 3, Class=Video, Driver=uvcvideo, 480M ID 5986:11cc Bison Electronics Inc. |__ Port 007: Dev 003, If 4, Class=Human Interface Device, Driver=usbhid, 480M ID 5986:11cc Bison Electronics Inc. |__ Port 007: Dev 003, If 5, Class=Application Specific Interface, Driver=[none], 480M ID 5986:11cc Bison Electronics Inc. /: Bus 004.Port 001: Dev 001, Class=root_hub, Driver=xhci_hcd/2p, 20000M/x2 ID 1d6b:0003 Linux Foundation 3.0 root hub Best regards, Eric ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-16 13:17 ` EricLin @ 2026-09-16 17:47 ` Michal Pecio 2026-09-17 12:29 ` EricLin 0 siblings, 1 reply; 11+ messages in thread From: Michal Pecio @ 2026-09-16 17:47 UTC (permalink / raw) To: EricLin; +Cc: gregkh, linux-usb, mathias.nyman, mathias.nyman On Wed, 16 Sep 2026 21:17:30 +0800, EricLin wrote: > I'm using fprint to operate this fingerprint sensor > > |__ Port 006: Dev 002, If 0, Class=Vendor Specific Class, Driver=[none], 12M > ID 27c6:6090 Shenzhen Goodix Technology Co.,Ltd. This all sounds like some userspace driver is used. And to me, this below looks like completely normal and successful USB2 device resume, followed by a reset initiated for unknown reason. [ 240.364611] xhci_hcd 0000:00:14.0: clear USB_PORT_FEAT_SUSPEND [ 240.364612] xhci_hcd 0000:00:14.0: PORTSC 0663 # PLS is suspend, write resume [ 240.364616] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x663, write 0x107e1 # PLS is resume, write U0 [ 240.405029] xhci_hcd 0000:00:14.0: Set port 3-6 link state, portsc: 0x7e3, write 0x10601 [ 240.405066] usb 3-6: usb auto-resume # reached U0 state [ 240.405138] xhci_hcd 0000:00:14.0: Port change event, 3-6, id 6, portsc: 0x400603 [ 240.405148] xhci_hcd 0000:00:14.0: handle_port_status: starting usb3 port polling. [ 240.446041] xhci_hcd 0000:00:14.0: Get port status 3-6 read: 0x603, return 0x40103 [ 240.446119] xhci_hcd 0000:00:14.0: clear port6 suspend/resume change, portsc: 0x603 # this would be "finish reset-resume" if one was intended # or "retry with reset-resume" if resume failed # see drivers/usb/core/hub.c::finish_port_resume() [ 240.456987] usb 3-6: finish resume [ 240.457379] xhci_hcd 0000:00:14.0: set port reset, actual port 3-6 status = 0x791 So maybe it's just the userspace software doing it for whatever reason on every use. Guess you could run "strace -eioctl" on this program to see if there is USBDEVFS_RESET each time the dmesg message shows up. Or add dump_stack() in usb_reset_device(), recompile and see what pops up. Probably ioctl syscall at the bottom of the call stack... Regards, Michal ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-16 17:47 ` Michal Pecio @ 2026-09-17 12:29 ` EricLin 2026-09-17 13:49 ` Michal Pecio 0 siblings, 1 reply; 11+ messages in thread From: EricLin @ 2026-09-17 12:29 UTC (permalink / raw) To: michal.pecio Cc: ericlin050914, gregkh, linux-usb, mathias.nyman, mathias.nyman > So maybe it's just the userspace software doing it for whatever reason > on every use. Guess you could run "strace -eioctl" on this program to > see if there is USBDEVFS_RESET each time the dmesg message shows up. Here are the outputs of strace $ strace -eioctl fprintd-verify ioctl(1, TCGETS2, {c_iflag=ICRNL|IXON|IUTF8, c_oflag=NL0|CR0|TAB0|BS0|VT0|FF0|OPOST|ONLCR, c_cflag=B38400|CS8|CREAD, c_lflag=ISIG|ICANON|ECHO|ECHOE|ECHOK|IEXTEN|ECHOCTL|ECHOKE, ...}) = 0 Using device /net/reactivated/Fprint/Device/0 ioctl(1, TCGETS2, {c_iflag=ICRNL|IXON|IUTF8, c_oflag=NL0|CR0|TAB0|BS0|VT0|FF0|OPOST|ONLCR, c_cflag=B38400|CS8|CREAD, c_lflag=ISIG|ICANON|ECHO|ECHOE|ECHOK|IEXTEN|ECHOCTL|ECHOKE, ...}) = 0 Listing enrolled fingers: ioctl(1, TCGETS2, {c_iflag=ICRNL|IXON|IUTF8, c_oflag=NL0|CR0|TAB0|BS0|VT0|FF0|OPOST|ONLCR, c_cflag=B38400|CS8|CREAD, c_lflag=ISIG|ICANON|ECHO|ECHOE|ECHOK|IEXTEN|ECHOCTL|ECHOKE, ...}) = 0 - #0: right-index-finger ioctl(1, TCGETS2, {c_iflag=ICRNL|IXON|IUTF8, c_oflag=NL0|CR0|TAB0|BS0|VT0|FF0|OPOST|ONLCR, c_cflag=B38400|CS8|CREAD, c_lflag=ISIG|ICANON|ECHO|ECHOE|ECHOK|IEXTEN|ECHOCTL|ECHOKE, ...}) = 0 Verify started! ioctl(1, TCGETS2, {c_iflag=ICRNL|IXON|IUTF8, c_oflag=NL0|CR0|TAB0|BS0|VT0|FF0|OPOST|ONLCR, c_cflag=B38400|CS8|CREAD, c_lflag=ISIG|ICANON|ECHO|ECHOE|ECHOK|IEXTEN|ECHOCTL|ECHOKE, ...}) = 0 Verifying: right-index-finger ioctl(1, TCGETS2, {c_iflag=ICRNL|IXON|IUTF8, c_oflag=NL0|CR0|TAB0|BS0|VT0|FF0|OPOST|ONLCR, c_cflag=B38400|CS8|CREAD, c_lflag=ISIG|ICANON|ECHO|ECHOE|ECHOK|IEXTEN|ECHOCTL|ECHOKE, ...}) = 0 Verify result: verify-match (done) +++ exited with 0 +++ > Or add dump_stack() in usb_reset_device(), recompile and see what pops > up. Probably ioctl syscall at the bottom of the call stack... I changed the hub.c code like this int usb_reset_device(struct usb_device *udev) { int ret; int i; unsigned int noio_flag; struct usb_port *port_dev; struct usb_host_config *config = udev->actconfig; struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); dump_stack(); // remaining code } And here are the outputs of dmesg [ 146.079223] CPU: 0 UID: 0 PID: 3544 Comm: fprintd Tainted: G W 7.3.0-rc3-1-cachyos-rc #2 PREEMPT(full) ca2d5051c95b910bac0a8f0497b52243cdaa75fa [ 146.079237] Tainted: [W]=WARN [ 146.079239] Hardware name: Micro-Star International Co., Ltd. Prestige 16 Flip AI+ C3MTG/MS-2622, BIOS E2622IMS.11A 08/12/2026 [ 146.079242] Call Trace: [ 146.079247] <TASK> [ 146.079253] dump_stack_lvl+0x61/0x80 [ 146.079267] usb_reset_device+0x4f/0x2b0 [ 146.079274] usbdev_ioctl+0x836/0xd80 [ 146.079282] __x64_sys_ioctl+0x76/0xc0 [ 146.079290] do_syscall_64+0x100/0x360 [ 146.079297] ? do_syscall_64+0x13b/0x360 [ 146.079300] ? do_file_open+0xd7/0x190 [ 146.079307] ? __kmalloc_node_noprof+0x317/0x520 [ 146.079313] ? alloc_cpumask_var_node+0x22/0x40 [ 146.079319] ? task_cache_work+0x614/0x640 [ 146.079329] ? exit_to_user_mode_loop+0x14c/0x820 [ 146.079338] ? current_time+0x39/0x150 [ 146.079348] ? usbdev_ioctl+0x291/0xd80 [ 146.079358] ? __x64_sys_ioctl+0xb8/0xc0 [ 146.079370] ? do_syscall_64+0x13b/0x360 [ 146.079377] ? wake_up_q+0x5c/0x90 [ 146.079388] ? futex_wake+0x1c6/0x200 [ 146.079401] ? do_futex+0x127/0x200 [ 146.079408] ? __se_sys_futex+0x13d/0x1d0 [ 146.079418] ? do_syscall_64+0x13b/0x360 [ 146.079424] ? irqentry_exit+0x3f/0x830 [ 146.079433] ? do_syscall_64+0x42/0x360 [ 146.079440] ? __irq_exit_rcu.llvm.4659499815316783039+0x6b/0x120 [ 146.079454] asm_fred_entrypoint_user+0x41/0x41 [ 146.079463] RIP: 0033:0x7a72c4b0b62d [ 146.079563] Code: 04 25 28 00 00 00 48 89 45 c8 31 c0 48 8d 45 10 c7 45 b0 10 00 00 00 48 89 45 b8 48 8d 45 d0 48 89 45 c0 b8 10 00 00 00 0f 05 <89> c2 3d 00 f0 ff ff 77 1a 48 8b 45 c8 64 48 2b 04 25 28 00 00 00 [ 146.079571] RSP: 002b:00007ffc6ad1fd20 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 146.079585] RAX: ffffffffffffffda RBX: 0000000000000020 RCX: 0000000000000dd8 [ 146.079589] RDX: 0000000000000000 RSI: 0000000000005514 RDI: 000000000000000b [ 146.079592] RBP: 00007ffc6ad1fd70 R08: 00007ffc6ad1fcc0 R09: 0000000000000000 [ 146.079594] R10: 0000000000000001 R11: 0000000000000000 R12: 00007a72a4005610 [ 146.079596] R13: 0000000000000000 R14: 000000000000000b R15: 00007a72a40017c0 [ 146.079602] </TASK> [ 146.191449] usb 3-6: reset full-speed USB device number 2 using xhci_hcd Regards, Eric ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-17 12:29 ` EricLin @ 2026-09-17 13:49 ` Michal Pecio 2026-09-17 14:18 ` EricLin 0 siblings, 1 reply; 11+ messages in thread From: Michal Pecio @ 2026-09-17 13:49 UTC (permalink / raw) To: EricLin; +Cc: gregkh, linux-usb, mathias.nyman, mathias.nyman On Thu, 17 Sep 2026 20:29:10 +0800, EricLin wrote: > Here are the outputs of strace > > $ strace -eioctl fprintd-verify > ioctl(1, TCGETS2, {c_iflag=ICRNL|IXON|IUTF8, c_oflag=NL0|CR0|TAB0|BS0|VT0|FF0|OPOST|ONLCR, c_cflag=B38400|CS8|CREAD, c_lflag=ISIG|ICANON|ECHO|ECHOE|ECHOK|IEXTEN|ECHOCTL|ECHOKE, ...}) = 0 > [...] This process isn't touching any USB device, maybe it forks something or talks to a daemon which does the dirty work. > [ 146.079223] CPU: 0 UID: 0 PID: 3544 Comm: fprintd Tainted: G W 7.3.0-rc3-1-cachyos-rc #2 PREEMPT(full) ca2d5051c95b910bac0a8f0497b52243cdaa75fa > [ 146.079237] Tainted: [W]=WARN > [ 146.079239] Hardware name: Micro-Star International Co., Ltd. Prestige 16 Flip AI+ C3MTG/MS-2622, BIOS E2622IMS.11A 08/12/2026 > [ 146.079242] Call Trace: > [ 146.079247] <TASK> > [ 146.079253] dump_stack_lvl+0x61/0x80 > [ 146.079267] usb_reset_device+0x4f/0x2b0 > [ 146.079274] usbdev_ioctl+0x836/0xd80 > [ 146.079282] __x64_sys_ioctl+0x76/0xc0 > [ 146.079290] do_syscall_64+0x100/0x360 The reset was requested by some "fprintd" process with PID 3544. At any rate, it's userspace doing this for whatever random reason. Your xhci-hcd dynamic dedug trace doesn't even hint at any USB layer problems like bad packets, device stalling endpoints, etc. If you want to konw why it happens, you need to dig in userspace. Regards, Michal ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG 2026-09-17 13:49 ` Michal Pecio @ 2026-09-17 14:18 ` EricLin 0 siblings, 0 replies; 11+ messages in thread From: EricLin @ 2026-09-17 14:18 UTC (permalink / raw) To: michal.pecio Cc: ericlin050914, gregkh, linux-usb, mathias.nyman, mathias.nyman > The reset was requested by some "fprintd" process with PID 3544. > At any rate, it's userspace doing this for whatever random reason. > Your xhci-hcd dynamic dedug trace doesn't even hint at any USB layer > problems like bad packets, device stalling endpoints, etc. > If you want to konw why it happens, you need to dig in userspace. Here are the outputs of tracing the fprintd daemon (Scanned twice) # strace -eioctl /usr/lib/fprintd ioctl(11, USBDEVFS_GET_CAPABILITIES, 0x599e9df8cbbc) = 0 ioctl(11, USBDEVFS_RESET, 0) = 0 ioctl(11, USBDEVFS_CLAIMINTERFACE, 0x7ffcd0ddc2a4) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9dfa9db0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df99470) = 0 ioctl(11, USBDEVFS_GET_CAPABILITIES, 0x599e9df99b2c) = 0 ioctl(11, USBDEVFS_RESET, 0) = 0 ioctl(11, USBDEVFS_CLAIMINTERFACE, 0x7ffcd0ddc334) = 0 # initialized ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df91c60) = 0 # First time ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df83560) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8002d20) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df8bfd0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df782c0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df91c60) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df83560) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8002d20) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df8bfd0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df782c0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df91c60) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df83560) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8002d20) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df8bfd0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df782c0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df835e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8004c60) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df843b0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8005bc0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b80054e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df843f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df835e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8004c60) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df84670) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df846b0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df8ef10) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df835e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8005bc0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8004c60) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df84670) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df84cd0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df84d10) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8005bc0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df843f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df835a0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df84670) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df84d50) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8005bc0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df84d10) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df843f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df84d10) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df8f040) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df91c60) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df85700) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8005bc0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df782c0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df835e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9dfa9db0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8006680) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df8e330) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df85700) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df782c0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9dfa9db0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df835e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df818f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df799c0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df8b710) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df782c0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7860b8006680) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df835e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9dfa9db0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df85700) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df782c0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df835e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df782c0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9dfa9db0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df85700) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x599e9df87850) = 0 ioctl(11, USBDEVFS_RELEASEINTERFACE, 0x7ffcd0ddc774) = 0 ioctl(11, USBDEVFS_GET_CAPABILITIES, 0x7944d80056ec) = 0 # Second time ioctl(11, USBDEVFS_RESET, 0) = 0 ioctl(11, USBDEVFS_CLAIMINTERFACE, 0x7ffd07cecc44) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8005470) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d80069f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf144b9350) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8003240) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf1449c2e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8005470) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d80069f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf144b9350) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8003240) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf1449c2e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8005470) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d80069f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf144b9350) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8003240) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf1449c2e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d80069f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8005470) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf144b9950) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf144a1c10) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf144aabc0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf144a1a10) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d80069f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf144b9950) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8005470) = 0 ioctl(11, USBDEVFS_DISCARDURB, 0x7944d8005470) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8002970) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x5fcf1449c2e0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944dc000f80) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d80069f0) = 0 ioctl(11, USBDEVFS_SUBMITURB, 0x7944d8005470) = 0 ioctl(11, USBDEVFS_RELEASEINTERFACE, 0x7ffd07ceccb4) = 0 So does it mean it's expected? Best Regards, Eric ^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2026-09-17 14:18 UTC | newest] Thread overview: 11+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2026-09-10 14:47 [BUG] Usb fingerprint sensor constantly resetting on MSI Prestige 16 Flip AI+ C3MTG Eric Lin 2026-09-11 9:53 ` Mathias Nyman 2026-09-11 12:11 ` EricLin 2026-09-11 13:39 ` Mathias Nyman 2026-09-11 14:48 ` EricLin 2026-09-11 20:21 ` Michal Pecio 2026-09-16 13:17 ` EricLin 2026-09-16 17:47 ` Michal Pecio 2026-09-17 12:29 ` EricLin 2026-09-17 13:49 ` Michal Pecio 2026-09-17 14:18 ` EricLin
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.