From: Stefan Ringel <stefan.ringel@arcor.de>
To: linux-media@vger.kernel.org
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>,
Devin Heitmueller <dheitmueller@kernellabs.com>
Subject: Re: [PATCH] - tm6000 DVB support
Date: Mon, 01 Feb 2010 21:35:57 +0100 [thread overview]
Message-ID: <4B673B2D.6040507@arcor.de> (raw)
In-Reply-To: <4B673790.3030706@arcor.de>
add Terratec Cinergy Hybrid XE
bugfix i2c transfer
add frontend callback
add init for tm6010
add digital-init for tm6010
add callback for analog/digital switch
bugfix usb transfer in DVB-mode
signed-off-by: Stefan Ringel <stefan.ringel@arcor.de>
diff --git a/drivers/media/common/tuners/tuner-xc2028.c
b/drivers/media/common/tuners/tuner-xc2028.c
index ed50168..2297c00 100644
--- a/drivers/media/common/tuners/tuner-xc2028.c
+++ b/drivers/media/common/tuners/tuner-xc2028.c
@@ -15,6 +15,7 @@
#include <linux/delay.h>
#include <media/tuner.h>
#include <linux/mutex.h>
+#include "compat.h"
#include <asm/unaligned.h>
#include "tuner-i2c.h"
#include "tuner-xc2028.h"
@@ -994,6 +995,13 @@ static int generic_set_freq(struct dvb_frontend
*fe, u32 freq /* in HZ */,
buf[0], buf[1], buf[2], buf[3],
freq / 1000000, (freq % 1000000) / 1000);
+ if (priv->ctrl.switch_mode) {
+ if (new_mode == T_ANALOG_TV)
+ do_tuner_callback(fe, SWITCH_TV_MODE, 0);
+ if (new_mode == T_DIGITAL_TV)
+ do_tuner_callback(fe, SWITCH_TV_MODE, 1);
+ }
+
rc = 0;
ret:
@@ -1114,7 +1122,11 @@ static int xc2028_set_params(struct dvb_frontend *fe,
/* All S-code tables need a 200kHz shift */
if (priv->ctrl.demod) {
- demod = priv->ctrl.demod + 200;
+ if (priv->ctrl.fname == "xc3028L-v36.fw") {
+ demod = priv->ctrl.demod;
+ } else {
+ demod = priv->ctrl.demod + 200;
+ }
/*
* The DTV7 S-code table needs a 700 kHz shift.
* Thanks to Terry Wu <terrywu2009@gmail.com> for reporting this
@@ -1123,8 +1135,8 @@ static int xc2028_set_params(struct dvb_frontend *fe,
* use this firmware after initialization, but a tune to a UHF
* channel should then cause DTV78 to be used.
*/
- if (type & DTV7)
- demod += 500;
+ if (type & DTV7)
+ demod += 500;
}
return generic_set_freq(fe, p->frequency,
@@ -1240,6 +1252,10 @@ static const struct dvb_tuner_ops
xc2028_dvb_tuner_ops = {
.get_rf_strength = xc2028_signal,
.set_params = xc2028_set_params,
.sleep = xc2028_sleep,
+#if 0
+ int (*get_bandwidth)(struct dvb_frontend *fe, u32 *bandwidth);
+ int (*get_status)(struct dvb_frontend *fe, u32 *status);
+#endif
};
struct dvb_frontend *xc2028_attach(struct dvb_frontend *fe,
diff --git a/drivers/media/common/tuners/tuner-xc2028.h
b/drivers/media/common/tuners/tuner-xc2028.h
index 9778c96..c9a4fb4 100644
--- a/drivers/media/common/tuners/tuner-xc2028.h
+++ b/drivers/media/common/tuners/tuner-xc2028.h
@@ -42,6 +42,7 @@ struct xc2028_ctrl {
unsigned int disable_power_mgmt:1;
unsigned int read_not_reliable:1;
unsigned int demod;
+ unsigned int switch_mode:1;
enum firmware_type type:2;
};
@@ -54,6 +55,7 @@ struct xc2028_config {
/* xc2028 commands for callback */
#define XC2028_TUNER_RESET 0
#define XC2028_RESET_CLK 1
+#define SWITCH_TV_MODE 2
#if defined(CONFIG_MEDIA_TUNER_XC2028) ||
(defined(CONFIG_MEDIA_TUNER_XC2028_MODULE) && defined(MODULE))
extern struct dvb_frontend *xc2028_attach(struct dvb_frontend *fe,
diff --git a/drivers/media/dvb/frontends/zl10353.h
b/drivers/media/dvb/frontends/zl10353.h
index 6e3ca9e..015bc36 100644
--- a/drivers/media/dvb/frontends/zl10353.h
+++ b/drivers/media/dvb/frontends/zl10353.h
@@ -45,6 +45,8 @@ struct zl10353_config
/* clock control registers (0x51-0x54) */
u8 clock_ctl_1; /* default: 0x46 */
u8 pll_0; /* default: 0x15 */
+
+ int tm6000:1;
};
#if defined(CONFIG_DVB_ZL10353) || (defined(CONFIG_DVB_ZL10353_MODULE)
&& defined(MODULE))
diff --git a/drivers/staging/tm6000/hack.c b/drivers/staging/tm6000/hack.c
index f181fce..c1e1880 100644
--- a/drivers/staging/tm6000/hack.c
+++ b/drivers/staging/tm6000/hack.c
@@ -37,7 +37,6 @@ static inline int tm6000_snd_control_msg(struct
tm6000_core *dev, __u8 request,
static int pseudo_zl10353_pll(struct tm6000_core *tm6000_dev, struct
dvb_frontend_parameters *p)
{
- int ret;
u8 *data = kzalloc(50*sizeof(u8), GFP_KERNEL);
printk(KERN_ALERT "should set frequency %u\n", p->frequency);
@@ -51,7 +50,7 @@ printk(KERN_ALERT "and bandwith %u\n",
p->u.ofdm.bandwidth);
}
// init ZL10353
- data[0] = 0x0b;
+/* data[0] = 0x0b;
ret = tm6000_snd_control_msg(tm6000_dev, 0x10, 0x501e, 0x00, data,
0x1);
msleep(15);
data[0] = 0x80;
@@ -159,7 +158,7 @@ printk(KERN_ALERT "and bandwith %u\n",
p->u.ofdm.bandwidth);
msleep(15);
data[0] = 0x5a;
ret = tm6000_snd_control_msg(tm6000_dev, 0x10, 0x651e,
0x00, data, 0x1);
- msleep(15);
+ msleep(15)
data[0] = 0xe9;
ret = tm6000_snd_control_msg(tm6000_dev, 0x10, 0x661e,
0x00, data, 0x1);
msleep(15);
@@ -189,7 +188,162 @@ printk(KERN_ALERT "and bandwith %u\n",
p->u.ofdm.bandwidth);
msleep(15);
break;
}
-
+*/
+ switch(p->u.ofdm.bandwidth) {
+ case BANDWIDTH_8_MHZ:
+ data[0] = 0x03;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x501e,0,data,1);
+ msleep(40);
+ data[0] = 0x44;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x511e,0,data,1);
+ msleep(40);
+ data[0] = 0x40;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x551e,0,data,1);
+ msleep(40);
+ data[0] = 0x46;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x521e,0,data,1);
+ msleep(40);
+ data[0] = 0x15;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x531e,0,data,1);
+ msleep(40);
+ data[0] = 0x0f;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x541e,0,data,1);
+ msleep(40);
+ data[0] = 0x80;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x551e,0,data,1);
+ msleep(40);
+ data[0] = 0x01;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0xea1e,0,data,1);
+ msleep(40);
+ data[0] = 0x00;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0xea1e,0,data,1);
+ msleep(40);
+ data[0] = 0x8b;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x631e,0,data,1);
+ msleep(40);
+ data[0] = 0x75;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0xcc1e,0,data,1);
+ msleep(40);
+ data[0] = 0xe6; //0x19;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x6c1e,0,data,1);
+ msleep(40);
+ data[0] = 0x09; //0xf7;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x6d1e,0,data,1);
+ msleep(40);
+ data[0] = 0x67;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x651e,0,data,1);
+ msleep(40);
+ data[0] = 0xe5;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x661e,0,data,1);
+ msleep(40);
+ data[0] = 0x75;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x5c1e,0,data,1);
+ msleep(40);
+ data[0] = 0x17;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x5f1e,0,data,1);
+ msleep(40);
+ data[0] = 0x40;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x5e1e,0,data,1);
+ msleep(40);
+ data[0] = 0x01;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x701e,0,data,1);
+ msleep(40);
+ break;
+ case BANDWIDTH_7_MHZ:
+ data[0] = 0x03;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x501e,0,data,1);
+ msleep(40);
+ data[0] = 0x44;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x511e,0,data,1);
+ msleep(40);
+ data[0] = 0x40;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x551e,0,data,1);
+ msleep(40);
+ data[0] = 0x46;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x521e,0,data,1);
+ msleep(40);
+ data[0] = 0x15;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x531e,0,data,1);
+ msleep(40);
+ data[0] = 0x0f;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x541e,0,data,1);
+ msleep(40);
+ data[0] = 0x80;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x551e,0,data,1);
+ msleep(40);
+ data[0] = 0x01;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0xea1e,0,data,1);
+ msleep(40);
+ data[0] = 0x00;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0xea1e,0,data,1);
+ msleep(40);
+ data[0] = 0x83;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x631e,0,data,1);
+ msleep(40);
+ data[0] = 0xa3;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0xcc1e,0,data,1);
+ msleep(40);
+ data[0] = 0xe6; //0x19;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x6c1e,0,data,1);
+ msleep(40);
+ data[0] = 0x09; //0xf7;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x6d1e,0,data,1);
+ msleep(40);
+ data[0] = 0x5a;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x651e,0,data,1);
+ msleep(40);
+ data[0] = 0xe9;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x661e,0,data,1);
+ msleep(40);
+ data[0] = 0x86;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x5c1e,0,data,1);
+ msleep(40);
+ data[0] = 0x17;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x5f1e,0,data,1);
+ msleep(40);
+ data[0] = 0x40;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x5e1e,0,data,1);
+ msleep(40);
+ data[0] = 0x01;
+ tm6000_read_write_usb(tm6000_dev,0x40,0x10,0x701e,0,data,1);
+ msleep(40);
+ break;
+ default:
+ printk(KERN_ALERT "tm6000: bandwidth not supported\n");
+ }
+
+ tm6000_read_write_usb(tm6000_dev,0xc0,0x10,0x051f,0,data,2);
+ printk(KERN_INFO "buf %#x %#x \n", data[0], data[1]);
+ msleep(40);
+
+ tm6000_read_write_usb(tm6000_dev,0xc0,0x10,0x051f,0,data,2);
+ printk(KERN_INFO "buf %#x %#x \n", data[0], data[1]);
+ msleep(40);
+
+ tm6000_read_write_usb(tm6000_dev,0xc0,0x10,0x051f,0,data,2);
+ printk(KERN_INFO "buf %#x %#x \n", data[0], data[1]);
+ msleep(40);
+
+ tm6000_read_write_usb(tm6000_dev,0xc0,0x10,0x051f,0,data,2);
+ printk(KERN_INFO "buf %#x %#x \n", data[0], data[1]);
+ msleep(40);
+
+ tm6000_read_write_usb(tm6000_dev,0xc0,0x10,0x051f,0,data,2);
+ printk(KERN_INFO "buf %#x %#x \n", data[0], data[1]);
+ msleep(40);
+
+ tm6000_read_write_usb(tm6000_dev,0xc0,0x10,0x0f1f,0,data,2);
+ printk(KERN_INFO "buf %#x %#x \n", data[0], data[1]);
+ msleep(40);
+
+ tm6000_read_write_usb(tm6000_dev,0xc0,0x10,0x091f,0,data,2);
+ printk(KERN_INFO "buf %#x %#x \n", data[0], data[1]);
+ msleep(40);
+
+ tm6000_read_write_usb(tm6000_dev,0xc0,0x10,0x0b1f,0,data,2);
+ printk(KERN_INFO "buf %#x %#x \n", data[0], data[1]);
+ msleep(40);
+
kfree(data);
return 0;
diff --git a/drivers/staging/tm6000/tm6000-cards.c
b/drivers/staging/tm6000/tm6000-cards.c
index 59fb505..652a54a 100644
--- a/drivers/staging/tm6000/tm6000-cards.c
+++ b/drivers/staging/tm6000/tm6000-cards.c
@@ -32,7 +32,7 @@
#include "tm6000.h"
#include "tm6000-regs.h"
#include "tuner-xc2028.h"
-#include "tuner-xc5000.h"
+#include "xc5000.h"
#define TM6000_BOARD_UNKNOWN 0
#define TM5600_BOARD_GENERIC 1
@@ -44,6 +44,10 @@
#define TM6000_BOARD_FREECOM_AND_SIMILAR 7
#define TM6000_BOARD_ADSTECH_MINI_DUAL_TV 8
#define TM6010_BOARD_HAUPPAUGE_900H 9
+#define TM6010_BOARD_BEHOLD_WANDER 10
+#define TM6010_BOARD_BEHOLD_VOYAGER 11
+#define TM6010_BOARD_TERRATEC_CINERGY_HYBRID_XE 12
+
#define TM6000_MAXBOARDS 16
static unsigned int card[] = {[0 ... (TM6000_MAXBOARDS - 1)] = UNSET };
@@ -208,7 +212,21 @@ struct tm6000_board tm6000_boards[] = {
},
.gpio_addr_tun_reset = TM6000_GPIO_2,
},
-
+ [TM6010_BOARD_TERRATEC_CINERGY_HYBRID_XE] = {
+ .name = "Terratec Cinergy Hybrid XE",
+ .tuner_type = TUNER_XC2028, /* has a XC3028 */
+ .tuner_addr = 0xc2 >> 1,
+ .demod_addr = 0x1e >> 1,
+ .type = TM6010,
+ .caps = {
+ .has_tuner = 1,
+ .has_dvb = 1,
+ .has_zl10353 = 1,
+ .has_eeprom = 1,
+ .has_remote = 1,
+ },
+ .gpio_addr_tun_reset = TM6010_GPIO_2,
+ }
};
/* table of devices that work with this driver */
@@ -221,12 +239,13 @@ struct usb_device_id tm6000_id_table [] = {
{ USB_DEVICE(0x2040, 0x6600), .driver_info =
TM6010_BOARD_HAUPPAUGE_900H },
{ USB_DEVICE(0x6000, 0xdec0), .driver_info =
TM6010_BOARD_BEHOLD_WANDER },
{ USB_DEVICE(0x6000, 0xdec1), .driver_info =
TM6010_BOARD_BEHOLD_VOYAGER },
+ { USB_DEVICE(0x0ccd, 0x0086), .driver_info =
TM6010_BOARD_TERRATEC_CINERGY_HYBRID_XE },
{ },
};
/* Tuner callback to provide the proper gpio changes needed for xc2028 */
-static int tm6000_tuner_callback(void *ptr, int component, int command,
int arg)
+int tm6000_tuner_callback(void *ptr, int component, int command, int arg)
{
int rc=0;
struct tm6000_core *dev = ptr;
@@ -252,11 +271,14 @@ static int tm6000_tuner_callback(void *ptr, int
component, int command, int arg)
switch (arg) {
case 0:
tm6000_set_reg (dev, REQ_03_SET_GET_MCU_PIN,
+ dev->tuner_reset_gpio, 0x01);
+ msleep(60);
+ tm6000_set_reg (dev, REQ_03_SET_GET_MCU_PIN,
dev->tuner_reset_gpio, 0x00);
- msleep(130);
+ msleep(75);
tm6000_set_reg (dev, REQ_03_SET_GET_MCU_PIN,
dev->tuner_reset_gpio, 0x01);
- msleep(130);
+ msleep(60);
break;
case 1:
tm6000_set_reg (dev, REQ_04_EN_DISABLE_MCU_INT,
@@ -269,13 +291,33 @@ static int tm6000_tuner_callback(void *ptr, int
component, int command, int arg)
TM6000_GPIO_CLK, 0);
if (rc<0)
return rc;
- msleep(100);
+ msleep(10);
rc=tm6000_set_reg (dev, REQ_03_SET_GET_MCU_PIN,
TM6000_GPIO_CLK, 1);
- msleep(100);
+ msleep(10);
+ break;
+ }
+ break;
+
+ case SWITCH_TV_MODE:
+ /* switch between analog and digital */
+ switch (arg) {
+ case 0:
+ printk(KERN_INFO "switch to analog");
+ tm6000_set_reg (dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_5, 1);
+ printk(KERN_INFO "analog");
+ break;
+ case 1:
+ printk(KERN_INFO "switch to digital");
+ tm6000_set_reg (dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_5, 0);
+ printk(KERN_INFO "digital");
break;
}
+ break;
}
+
return (rc);
}
@@ -290,7 +332,7 @@ static void tm6000_config_tuner (struct tm6000_core
*dev)
memset(&tun_setup, 0, sizeof(tun_setup));
tun_setup.type = dev->tuner_type;
tun_setup.addr = dev->tuner_addr;
- tun_setup.mode_mask = T_ANALOG_TV | T_RADIO;
+ tun_setup.mode_mask = T_ANALOG_TV | T_RADIO | T_DIGITAL_TV;
tun_setup.tuner_callback = tm6000_tuner_callback;
v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, s_type_addr,
&tun_setup);
@@ -302,15 +344,19 @@ static void tm6000_config_tuner (struct
tm6000_core *dev)
memset(&xc2028_cfg, 0, sizeof(xc2028_cfg));
memset (&ctl,0,sizeof(ctl));
- ctl.mts = 1;
- ctl.read_not_reliable = 1;
+ ctl.input1 = 1;
+ ctl.read_not_reliable = 0;
ctl.msleep = 10;
-
+ ctl.demod = XC3028_FE_ZARLINK456;
+ ctl.vhfbw7 = 1;
+ ctl.uhfbw8 = 1;
+ ctl.switch_mode = 1;
xc2028_cfg.tuner = TUNER_XC2028;
xc2028_cfg.priv = &ctl;
switch(dev->model) {
case TM6010_BOARD_HAUPPAUGE_900H:
+ case TM6010_BOARD_TERRATEC_CINERGY_HYBRID_XE:
ctl.fname = "xc3028L-v36.fw";
break;
default:
@@ -402,6 +448,7 @@ static int tm6000_init_dev(struct tm6000_core *dev)
}
#endif
}
+ return 0;
err2:
v4l2_device_unregister(&dev->v4l2_dev);
@@ -459,13 +506,13 @@ static int tm6000_usb_probe(struct usb_interface
*interface,
/* Check to see next free device and mark as used */
nr=find_first_zero_bit(&tm6000_devused,TM6000_MAXBOARDS);
if (nr >= TM6000_MAXBOARDS) {
- printk ("tm6000: Supports only %i em28xx
boards.\n",TM6000_MAXBOARDS);
+ printk ("tm6000: Supports only %i tm60xx
boards.\n",TM6000_MAXBOARDS);
usb_put_dev(usbdev);
return -ENOMEM;
}
/* Create and initialize dev struct */
- dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+ dev = kzalloc(sizeof(*(dev)), GFP_KERNEL);
if (dev == NULL) {
printk ("tm6000" ": out of memory!\n");
usb_put_dev(usbdev);
diff --git a/drivers/staging/tm6000/tm6000-core.c
b/drivers/staging/tm6000/tm6000-core.c
index d41af1d..33bbbd3 100644
--- a/drivers/staging/tm6000/tm6000-core.c
+++ b/drivers/staging/tm6000/tm6000-core.c
@@ -219,33 +219,53 @@ int tm6000_init_analog_mode (struct tm6000_core *dev)
int tm6000_init_digital_mode (struct tm6000_core *dev)
{
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00ff, 0x08);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00ff, 0x00);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x003f, 0x01);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00df, 0x08);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00e2, 0x0c);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00e8, 0xff);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00eb, 0xd8);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00c0, 0x40);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00c1, 0xd0);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00c3, 0x09);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00da, 0x37);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00d1, 0xd8);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00d2, 0xc0);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00d6, 0x60);
-
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00e2, 0x0c);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00e8, 0xff);
- tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00eb, 0x08);
- msleep(50);
-
- tm6000_set_reg (dev, REQ_04_EN_DISABLE_MCU_INT, 0x0020, 0x00);
- msleep(50);
- tm6000_set_reg (dev, REQ_04_EN_DISABLE_MCU_INT, 0x0020, 0x01);
- msleep(50);
- tm6000_set_reg (dev, REQ_04_EN_DISABLE_MCU_INT, 0x0020, 0x00);
- msleep(100);
-
+ if (dev->dev_type == TM6010) {
+ int val;
+ u8 buf[2];
+
+ /* digital init */
+ val = tm6000_get_reg(dev, REQ_07_SET_GET_AVREG, 0xcc, 0);
+ val &= ~0x60;
+ tm6000_set_reg(dev, REQ_07_SET_GET_AVREG, 0xcc, val);
+ val = tm6000_get_reg(dev, REQ_07_SET_GET_AVREG, 0xc0, 0);
+ val |= 0x40;
+ tm6000_set_reg(dev, REQ_07_SET_GET_AVREG, 0xc0, val);
+ tm6000_set_reg(dev, REQ_07_SET_GET_AVREG, 0xfe, 0x28);
+ tm6000_set_reg(dev, REQ_08_SET_GET_AVREG_BIT, 0xe2, 0xfc);
+ tm6000_set_reg(dev, REQ_08_SET_GET_AVREG_BIT, 0xe6, 0xff);
+ tm6000_set_reg(dev, REQ_08_SET_GET_AVREG_BIT, 0xf1, 0xfe);
+ tm6000_read_write_usb (dev, 0xc0, 0x0e, 0x00c2, 0x0008, buf, 2);
+ printk (KERN_INFO "buf %#x %#x \n", buf[0], buf[1]);
+
+
+ } else {
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00ff, 0x08);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00ff, 0x00);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x003f, 0x01);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00df, 0x08);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00e2, 0x0c);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00e8, 0xff);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00eb, 0xd8);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00c0, 0x40);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00c1, 0xd0);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00c3, 0x09);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00da, 0x37);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00d1, 0xd8);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00d2, 0xc0);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00d6, 0x60);
+
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00e2, 0x0c);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00e8, 0xff);
+ tm6000_set_reg (dev, REQ_07_SET_GET_AVREG, 0x00eb, 0x08);
+ msleep(50);
+
+ tm6000_set_reg (dev, REQ_04_EN_DISABLE_MCU_INT, 0x0020, 0x00);
+ msleep(50);
+ tm6000_set_reg (dev, REQ_04_EN_DISABLE_MCU_INT, 0x0020, 0x01);
+ msleep(50);
+ tm6000_set_reg (dev, REQ_04_EN_DISABLE_MCU_INT, 0x0020, 0x00);
+ msleep(100);
+ }
return 0;
}
@@ -394,7 +414,15 @@ struct reg_init tm6010_init_tab[] = {
{ REQ_07_SET_GET_AVREG, 0x3f, 0x00 },
{ REQ_05_SET_GET_USBREG, 0x18, 0x00 },
-
+
+ /* additional from Terratec Cinergy Hybrid XE */
+ { REQ_07_SET_GET_AVREG, 0xdc, 0xaa },
+ { REQ_07_SET_GET_AVREG, 0xdd, 0x30 },
+ { REQ_07_SET_GET_AVREG, 0xde, 0x20 },
+ { REQ_07_SET_GET_AVREG, 0xdf, 0xd0 },
+ { REQ_04_EN_DISABLE_MCU_INT, 0x02, 0x00 },
+ { REQ_07_SET_GET_AVREG, 0xd8, 0x2f },
+
/* set remote wakeup key:any key wakeup */
{ REQ_07_SET_GET_AVREG, 0xe5, 0xfe },
{ REQ_07_SET_GET_AVREG, 0xda, 0xff },
@@ -404,6 +432,7 @@ int tm6000_init (struct tm6000_core *dev)
{
int board, rc=0, i, size;
struct reg_init *tab;
+ u8 buf[40];
if (dev->dev_type == TM6010) {
tab = tm6010_init_tab;
@@ -424,61 +453,129 @@ int tm6000_init (struct tm6000_core *dev)
}
}
- msleep(5); /* Just to be conservative */
-
- /* Check board version - maybe 10Moons specific */
- board=tm6000_get_reg16 (dev, 0x40, 0, 0);
- if (board >=0) {
- printk (KERN_INFO "Board version = 0x%04x\n",board);
- } else {
- printk (KERN_ERR "Error %i while retrieving board
version\n",board);
- }
-
+ /* hack */
if (dev->dev_type == TM6010) {
- /* Turn xceive 3028 on */
- tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN, TM6010_GPIO_3, 0x01);
- msleep(11);
- }
-
- /* Reset GPIO1 and GPIO4. */
- for (i=0; i< 2; i++) {
- rc = tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
- dev->tuner_reset_gpio, 0x00);
- if (rc<0) {
- printk (KERN_ERR "Error %i doing GPIO1 reset\n",rc);
- return rc;
- }
-
- msleep(10); /* Just to be conservative */
- rc = tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
- dev->tuner_reset_gpio, 0x01);
- if (rc<0) {
- printk (KERN_ERR "Error %i doing GPIO1 reset\n",rc);
- return rc;
- }
-
- msleep(10);
- rc=tm6000_set_reg (dev, REQ_03_SET_GET_MCU_PIN, TM6000_GPIO_4, 0);
- if (rc<0) {
- printk (KERN_ERR "Error %i doing GPIO4 reset\n",rc);
- return rc;
- }
-
- msleep(10);
- rc=tm6000_set_reg (dev, REQ_03_SET_GET_MCU_PIN, TM6000_GPIO_4, 1);
- if (rc<0) {
- printk (KERN_ERR "Error %i doing GPIO4 reset\n",rc);
- return rc;
- }
-
- if (!i) {
- rc=tm6000_get_reg16(dev, 0x40,0,0);
- if (rc>=0) {
- printk ("board=%d\n", rc);
+
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_4, 0);
+ msleep(15);
+
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_1, 0);
+
+ msleep(50);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_1, 1);
+
+ msleep(15);
+ tm6000_read_write_usb (dev, 0xc0, 0x0e, 0x0010, 0x4400, buf, 2);
+
+ msleep(15);
+ tm6000_read_write_usb (dev, 0xc0, 0x10, 0xf432, 0x0000, buf, 2);
+
+ msleep(15);
+ buf[0] = 0x12;
+ buf[1] = 0x34;
+ tm6000_read_write_usb (dev, 0x40, 0x10, 0xf432, 0x0000, buf, 2);
+
+ msleep(15);
+ tm6000_read_write_usb (dev, 0xc0, 0x10, 0xf432, 0x0000, buf, 2);
+
+ msleep(15);
+ tm6000_read_write_usb (dev, 0xc0, 0x10, 0x0032, 0x0000, buf, 2);
+
+ msleep(15);
+ buf[0] = 0x00;
+ buf[1] = 0x01;
+ tm6000_read_write_usb (dev, 0x40, 0x10, 0xf332, 0x0000, buf, 2);
+
+ msleep(15);
+ tm6000_read_write_usb (dev, 0xc0, 0x10, 0x00c0, 0x0000, buf, 39);
+
+ msleep(15);
+ buf[0] = 0x00;
+ buf[1] = 0x00;
+ tm6000_read_write_usb (dev, 0x40, 0x10, 0xf332, 0x0000, buf, 2);
+
+ msleep(15);
+ tm6000_read_write_usb (dev, 0xc0, 0x10, 0x7f1f, 0x0000, buf, 2);
+// printk(KERN_INFO "buf %#x %#x \n", buf[0], buf [1]);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_4, 1);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_0, 1);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_7, 0);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_5, 1);
+
+ msleep(15);
+
+ for (i=0; i< size; i++) {
+ rc= tm6000_set_reg (dev, tab[i].req, tab[i].reg, tab[i].val);
+ if (rc<0) {
+ printk (KERN_ERR "Error %i while setting req %d, "
+ "reg %d to value %d\n", rc,
+ tab[i].req,tab[i].reg, tab[i].val);
+ return rc;
}
}
+
+ msleep(15);
+
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_4, 0);
+ msleep(15);
+
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_1, 0);
+
+ msleep(50);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_1, 1);
+
+ msleep(15);
+ tm6000_read_write_usb (dev, 0xc0, 0x0e, 0x00c2, 0x0008, buf, 2);
+// printk(KERN_INFO "buf %#x %#x \n", buf[0], buf[1]);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_2, 1);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_2, 0);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_2, 1);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_2, 1);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_2, 0);
+ msleep(15);
+ tm6000_set_reg(dev, REQ_03_SET_GET_MCU_PIN,
+ TM6010_GPIO_2, 1);
+ msleep(15);
}
+ /* hack end */
+
+ msleep(5); /* Just to be conservative */
+ /* Check board version - maybe 10Moons specific */
+ if (dev->dev_type == TM5600) {
+ board=tm6000_get_reg16 (dev, 0x40, 0, 0);
+ if (board >=0) {
+ printk (KERN_INFO "Board version = 0x%04x\n",board);
+ } else {
+ printk (KERN_ERR "Error %i while retrieving board
version\n",board);
+ }
+ }
+
msleep(50);
return 0;
diff --git a/drivers/staging/tm6000/tm6000-dvb.c
b/drivers/staging/tm6000/tm6000-dvb.c
index e900d6d..31458d3 100644
--- a/drivers/staging/tm6000/tm6000-dvb.c
+++ b/drivers/staging/tm6000/tm6000-dvb.c
@@ -17,7 +17,9 @@
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
+#include <linux/kernel.h>
#include <linux/usb.h>
+#include <compat.h>
#include "tm6000.h"
#include "tm6000-regs.h"
@@ -30,17 +32,61 @@
#include "tuner-xc2028.h"
+static void inline print_err_status (struct tm6000_core *dev,
+ int packet, int status)
+{
+ char *errmsg = "Unknown";
+
+ switch(status) {
+ case -ENOENT:
+ errmsg = "unlinked synchronuously";
+ break;
+ case -ECONNRESET:
+ errmsg = "unlinked asynchronuously";
+ break;
+ case -ENOSR:
+ errmsg = "Buffer error (overrun)";
+ break;
+ case -EPIPE:
+ errmsg = "Stalled (device not responding)";
+ break;
+ case -EOVERFLOW:
+ errmsg = "Babble (bad cable?)";
+ break;
+ case -EPROTO:
+ errmsg = "Bit-stuff error (bad cable?)";
+ break;
+ case -EILSEQ:
+ errmsg = "CRC/Timeout (could be anything)";
+ break;
+ case -ETIME:
+ errmsg = "Device does not respond";
+ break;
+ }
+ if (packet<0) {
+ dprintk(dev, 1, "URB status %d [%s].\n",
+ status, errmsg);
+ } else {
+ dprintk(dev, 1, "URB packet %d, status %d [%s].\n",
+ packet, status, errmsg);
+ }
+}
+
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,19)
+static void tm6000_urb_received(struct urb *urb, struct pt_regs *ptregs)
+#else
static void tm6000_urb_received(struct urb *urb)
+#endif
{
int ret;
struct tm6000_core* dev = urb->context;
- if(urb->status != 0){
- printk(KERN_ERR "tm6000: status != 0\n");
+ if(urb->status != 0) {
+ print_err_status (dev,0,urb->status);
}
else if(urb->actual_length>0){
- dvb_dmx_swfilter(&dev->dvb->demux, urb->transfer_buffer,
- urb->actual_length);
+ dvb_dmx_swfilter(&dev->dvb->demux, urb->transfer_buffer,
urb->actual_length);
}
if(dev->dvb->streams > 0) {
@@ -56,49 +102,37 @@ static void tm6000_urb_received(struct urb *urb)
int tm6000_start_stream(struct tm6000_core *dev)
{
int ret;
- unsigned int pipe, maxPaketSize;
+ unsigned int pipe, size;
struct tm6000_dvb *dvb = dev->dvb;
printk(KERN_INFO "tm6000: got start stream request %s\n",__FUNCTION__);
tm6000_init_digital_mode(dev);
-/*
- ret = tm6000_set_led_status(tm6000_dev, 0x1);
- if(ret < 0) {
- return -1;
- }
-*/
-
dvb->bulk_urb = usb_alloc_urb(0, GFP_KERNEL);
if(dvb->bulk_urb == NULL) {
printk(KERN_ERR "tm6000: couldn't allocate urb\n");
return -ENOMEM;
}
- maxPaketSize = dev->bulk_in->desc.wMaxPacketSize;
+ pipe = usb_rcvbulkpipe(dev->udev, dev->bulk_in->desc.bEndpointAddress
+ & USB_ENDPOINT_NUMBER_MASK);
+
+ size = usb_maxpacket(dev->udev, pipe, usb_pipeout(pipe));
+ size = size * 15; // 512 x 8 or 12 or 15
- dvb->bulk_urb->transfer_buffer = kzalloc(maxPaketSize, GFP_KERNEL);
+ dvb->bulk_urb->transfer_buffer = kzalloc(size, GFP_KERNEL);
if(dvb->bulk_urb->transfer_buffer == NULL) {
usb_free_urb(dvb->bulk_urb);
printk(KERN_ERR "tm6000: couldn't allocate transfer buffer!\n");
return -ENOMEM;
}
-
- pipe = usb_rcvbulkpipe(dev->udev, dev->bulk_in->desc.bEndpointAddress
- & USB_ENDPOINT_NUMBER_MASK);
-
+
usb_fill_bulk_urb(dvb->bulk_urb, dev->udev, pipe,
dvb->bulk_urb->transfer_buffer,
- maxPaketSize,
+ size,
tm6000_urb_received, dev);
- ret = usb_set_interface(dev->udev, 0, 1);
- if(ret < 0) {
- printk(KERN_ERR "tm6000: error %i in %s during set
interface\n", ret, __FUNCTION__);
- return ret;
- }
-
ret = usb_clear_halt(dev->udev, pipe);
if(ret < 0) {
printk(KERN_ERR "tm6000: error %i in %s during pipe
reset\n",ret,__FUNCTION__);
@@ -107,15 +141,14 @@ int tm6000_start_stream(struct tm6000_core *dev)
else {
printk(KERN_ERR "tm6000: pipe resetted\n");
}
-
-// mutex_lock(&tm6000_driver.open_close_mutex);
+
+// mutex_lock(&tm6000_driver.open_close_mutex);
ret = usb_submit_urb(dvb->bulk_urb, GFP_KERNEL);
-
-// mutex_unlock(&tm6000_driver.open_close_mutex);
+// mutex_unlock(&tm6000_driver.open_close_mutex);
if (ret) {
printk(KERN_ERR "tm6000: submit of urb failed (error=%i)\n",ret);
-
+
kfree(dvb->bulk_urb->transfer_buffer);
usb_free_urb(dvb->bulk_urb);
return ret;
@@ -126,18 +159,12 @@ int tm6000_start_stream(struct tm6000_core *dev)
void tm6000_stop_stream(struct tm6000_core *dev)
{
- int ret;
struct tm6000_dvb *dvb = dev->dvb;
-// tm6000_set_led_status(tm6000_dev, 0x0);
-
- ret = usb_set_interface(dev->udev, 0, 0);
- if(ret < 0) {
- printk(KERN_ERR "tm6000: error %i in %s during set
interface\n",ret,__FUNCTION__);
- }
-
if(dvb->bulk_urb) {
+ printk (KERN_INFO "urb killing\n");
usb_kill_urb(dvb->bulk_urb);
+ printk (KERN_INFO "urb buffer free\n");
kfree(dvb->bulk_urb->transfer_buffer);
usb_free_urb(dvb->bulk_urb);
dvb->bulk_urb = NULL;
@@ -154,7 +181,7 @@ int tm6000_start_feed(struct dvb_demux_feed *feed)
mutex_lock(&dvb->mutex);
if(dvb->streams == 0) {
dvb->streams = 1;
-// mutex_init(&tm6000_dev->streaming_mutex);
+// mutex_init(&tm6000_dev->streming_mutex);
tm6000_start_stream(dev);
}
else {
@@ -173,14 +200,17 @@ int tm6000_stop_feed(struct dvb_demux_feed *feed) {
printk(KERN_INFO "tm6000: got stop feed request %s\n",__FUNCTION__);
mutex_lock(&dvb->mutex);
- --dvb->streams;
- if(0 == dvb->streams) {
+ printk (KERN_INFO "stream %#x\n", dvb->streams);
+ --(dvb->streams);
+ if(dvb->streams == 0) {
+ printk (KERN_INFO "stop stream\n");
tm6000_stop_stream(dev);
-// mutex_destroy(&tm6000_dev->streaming_mutex);
+// mutex_destroy(&tm6000_dev->streaming_mutex);
}
+
mutex_unlock(&dvb->mutex);
-// mutex_destroy(&tm6000_dev->streaming_mutex);
+// mutex_destroy(&tm6000_dev->streaming_mutex);
return 0;
}
@@ -191,13 +221,16 @@ int tm6000_dvb_attach_frontend(struct tm6000_core
*dev)
if(dev->caps.has_zl10353) {
struct zl10353_config config =
- {.demod_address = dev->demod_addr >> 1,
+ {.demod_address = dev->demod_addr,
.no_tuner = 1,
-// .input_frequency = 0x19e9,
-// .r56_agc_targets = 0x1c,
+ .parallel_ts = 1,
+ .if2 = 45700,
+ .disable_i2c_gate_ctrl = 1,
+ .tm6000 = 1,
};
dvb->frontend = pseudo_zl10353_attach(dev, &config,
+// dvb->frontend = dvb_attach (zl10353_attach, &config,
&dev->i2c_adap);
}
else {
@@ -235,7 +268,8 @@ int tm6000_dvb_register(struct tm6000_core *dev)
.i2c_adap = &dev->i2c_adap,
.i2c_addr = dev->tuner_addr,
};
-
+
+ dvb->frontend->callback = tm6000_tuner_callback;
ret = dvb_register_frontend(&dvb->adapter, dvb->frontend);
if (ret < 0) {
printk(KERN_ERR
@@ -258,8 +292,8 @@ int tm6000_dvb_register(struct tm6000_core *dev)
dvb->demux.dmx.capabilities = DMX_TS_FILTERING | DMX_SECTION_FILTERING
| DMX_MEMORY_BASED_FILTERING;
dvb->demux.priv = dev;
- dvb->demux.filternum = 256;
- dvb->demux.feednum = 256;
+ dvb->demux.filternum = 5; //256;
+ dvb->demux.feednum = 5; //256;
dvb->demux.start_feed = tm6000_start_feed;
dvb->demux.stop_feed = tm6000_stop_feed;
dvb->demux.write_to_decoder = NULL;
@@ -307,7 +341,7 @@ void tm6000_dvb_unregister(struct tm6000_core *dev)
usb_free_urb(bulk_urb);
}
-// mutex_lock(&tm6000_driver.open_close_mutex);
+// mutex_lock(&tm6000_driver.open_close_mutex);
if(dvb->frontend) {
dvb_frontend_detach(dvb->frontend);
dvb_unregister_frontend(dvb->frontend);
@@ -317,6 +351,6 @@ void tm6000_dvb_unregister(struct tm6000_core *dev)
dvb_dmx_release(&dvb->demux);
dvb_unregister_adapter(&dvb->adapter);
mutex_destroy(&dvb->mutex);
-// mutex_unlock(&tm6000_driver.open_close_mutex);
+// mutex_unlock(&tm6000_driver.open_close_mutex);
}
diff --git a/drivers/staging/tm6000/tm6000-i2c.c
b/drivers/staging/tm6000/tm6000-i2c.c
index 4da10f5..3e43ad7 100644
--- a/drivers/staging/tm6000/tm6000-i2c.c
+++ b/drivers/staging/tm6000/tm6000-i2c.c
@@ -86,6 +86,11 @@ static int tm6000_i2c_xfer(struct i2c_adapter *i2c_adap,
msgs[i].len == 1 ? 0 : msgs[i].buf[1],
msgs[i + 1].buf, msgs[i + 1].len);
i++;
+
+ if ((dev->dev_type == TM6010) && (addr == 0xc2)) {
+ tm6000_set_reg(dev, 0x32, 0,0);
+ tm6000_set_reg(dev, 0x33, 0,0);
+ }
if (i2c_debug >= 2)
for (byte = 0; byte < msgs[i].len; byte++)
printk(" %02x", msgs[i].buf[byte]);
@@ -99,6 +104,12 @@ static int tm6000_i2c_xfer(struct i2c_adapter *i2c_adap,
REQ_16_SET_GET_I2C_WR1_RDN,
addr | msgs[i].buf[0] << 8, 0,
msgs[i].buf + 1, msgs[i].len - 1);
+
+
+ if ((dev->dev_type == TM6010) && (addr == 0xc2)) {
+ tm6000_set_reg(dev, 0x32, 0,0);
+ tm6000_set_reg(dev, 0x33, 0,0);
+ }
}
if (i2c_debug >= 2)
printk("\n");
@@ -198,7 +209,7 @@ static struct i2c_algorithm tm6000_algo = {
static struct i2c_adapter tm6000_adap_template = {
.owner = THIS_MODULE,
- .class = I2C_CLASS_TV_ANALOG,
+ .class = I2C_CLASS_TV_ANALOG | I2C_CLASS_TV_DIGITAL,
.name = "tm6000",
.id = I2C_HW_B_TM6000,
.algo = &tm6000_algo,
diff --git a/drivers/staging/tm6000/tm6000.h
b/drivers/staging/tm6000/tm6000.h
index 877cbf6..e403ca0 100644
--- a/drivers/staging/tm6000/tm6000.h
+++ b/drivers/staging/tm6000/tm6000.h
@@ -23,12 +23,15 @@
// Use the tm6000-hack, instead of the proper initialization code
//#define HACK 1
+#include "compat.h"
#include <linux/videodev2.h>
#include <media/v4l2-common.h>
#include <media/videobuf-vmalloc.h>
#include "tm6000-usb-isoc.h"
#include <linux/i2c.h>
+#if LINUX_VERSION_CODE > KERNEL_VERSION(2,6,15)
#include <linux/mutex.h>
+#endif
#include <media/v4l2-device.h>
@@ -78,6 +81,10 @@ struct tm6000_dmaqueue {
/* thread for generating video stream*/
struct task_struct *kthread;
wait_queue_head_t wq;
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0)
+ struct semaphore *notify;
+ int rmmod:1;
+#endif
/* Counters to control fps rate */
int frame;
int ini_jiffies;
@@ -90,12 +97,14 @@ enum tm6000_core_state {
DEV_MISCONFIGURED = 0x04,
};
+#if 1
/* io methods */
enum tm6000_io_method {
IO_NONE,
IO_READ,
IO_MMAP,
};
+#endif
enum tm6000_mode {
TM6000_MODE_UNKNOWN=0,
@@ -202,6 +211,9 @@ struct tm6000_fh {
V4L2_STD_PAL_M|V4L2_STD_PAL_60|V4L2_STD_NTSC_M| \
V4L2_STD_NTSC_M_JP|V4L2_STD_SECAM
+/* In tm6000-cards.c */
+
+int tm6000_tuner_callback (void *ptr, int component, int command, int arg);
/* In tm6000-core.c */
int tm6000_read_write_usb (struct tm6000_core *dev, u8 reqtype, u8 req,
@@ -209,7 +221,6 @@ int tm6000_read_write_usb (struct tm6000_core *dev,
u8 reqtype, u8 req,
int tm6000_get_reg (struct tm6000_core *dev, u8 req, u16 value, u16 index);
int tm6000_set_reg (struct tm6000_core *dev, u8 req, u16 value, u16 index);
int tm6000_init (struct tm6000_core *dev);
-int tm6000_init_after_firmware (struct tm6000_core *dev);
int tm6000_init_analog_mode (struct tm6000_core *dev);
int tm6000_init_digital_mode (struct tm6000_core *dev);
@@ -231,7 +242,12 @@ int tm6000_set_standard (struct tm6000_core *dev,
v4l2_std_id *norm);
int tm6000_i2c_register(struct tm6000_core *dev);
int tm6000_i2c_unregister(struct tm6000_core *dev);
+#if 1
/* In tm6000-queue.c */
+#if 0
+int tm6000_init_isoc(struct tm6000_core *dev, int max_packets);
+void tm6000_uninit_isoc(struct tm6000_core *dev);
+#endif
int tm6000_v4l2_mmap(struct file *filp, struct vm_area_struct *vma);
@@ -276,3 +292,4 @@ extern int tm6000_debug;
__FUNCTION__ , ##arg); } while (0)
+#endif
--
Stefan Ringel <stefan.ringel@arcor.de>
next prev parent reply other threads:[~2010-02-01 20:36 UTC|newest]
Thread overview: 55+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-02-01 20:20 [PATCH] - tm6000 DVB support Stefan Ringel
2010-02-01 20:35 ` Stefan Ringel [this message]
2010-02-01 20:52 ` Devin Heitmueller
2010-02-01 21:23 ` Stefan Ringel
2010-02-01 21:44 ` Devin Heitmueller
2010-02-01 22:00 ` Stefan Ringel
2010-02-01 23:05 ` Mauro Carvalho Chehab
2010-02-02 16:14 ` Stefan Ringel
2010-02-02 16:44 ` Mauro Carvalho Chehab
2010-02-02 17:38 ` Stefan Ringel
2010-02-02 20:05 ` Mauro Carvalho Chehab
2010-02-01 22:52 ` Mauro Carvalho Chehab
2010-02-02 17:24 ` Stefan Ringel
2010-02-02 20:03 ` Mauro Carvalho Chehab
2010-02-02 20:19 ` Stefan Ringel
2010-02-02 20:30 ` Mauro Carvalho Chehab
2010-02-02 20:42 ` Stefan Ringel
2010-02-02 20:52 ` Mauro Carvalho Chehab
2010-02-02 21:11 ` Stefan Ringel
2010-02-03 20:10 ` [PATCH 1/15] - tm6000 build hunk Stefan Ringel
2010-02-03 20:13 ` [PATCH 2/15] - tm6000 add Terratec Cinergy Hybrid XE Stefan Ringel
2010-02-03 20:15 ` [PATCH 3/15] - tm6000 bugfix hunk in init_dev Stefan Ringel
2010-02-03 20:22 ` Mauro Carvalho Chehab
2010-02-03 20:16 ` [PATCH 4/15] - tm6000.h Stefan Ringel
2010-02-03 20:25 ` Mauro Carvalho Chehab
2010-02-03 20:50 ` Stefan Ringel
2010-02-03 20:58 ` Devin Heitmueller
2010-02-03 21:31 ` Mauro Carvalho Chehab
2010-02-03 20:18 ` [PATCH 5/15] - tm6000 bugfix i2c transfer Stefan Ringel
2010-02-03 20:18 ` [PATCH 2/15] - tm6000 add Terratec Cinergy Hybrid XE Mauro Carvalho Chehab
2010-02-03 20:20 ` [PATCH 6/15] - tm6000 bugfix usb transfer in DVB mode Stefan Ringel
2010-02-03 20:22 ` [PATCH 7/15] - tm6000 Stefan Ringel
2010-02-03 20:23 ` [PATCH 2/15] - tm6000 bugfix Stefan Ringel
2010-02-03 20:25 ` [PATCH 9/15] - tm6000 analog digital switch Stefan Ringel
2010-02-03 20:40 ` Mauro Carvalho Chehab
2010-02-03 20:55 ` Stefan Ringel
2010-02-03 21:21 ` Mauro Carvalho Chehab
2010-02-03 20:27 ` [PATCH 2/15] - tm6000 add digital init for tm6010 Stefan Ringel
2010-02-03 20:29 ` [PATCH 11/15] - tm6000 add " Stefan Ringel
2010-02-03 20:31 ` [PATCH 12/15] - tm6000 bugfix tuner reset time and tuner param Stefan Ringel
2010-02-03 20:52 ` Devin Heitmueller
2010-02-03 21:15 ` Stefan Ringel
2010-02-03 20:36 ` [PATCH 13/15] - xc2028 bugfix for firmware 3.6 -> Zarlink use without shift in DTV8 or DTV78 Stefan Ringel
2010-02-03 20:45 ` Devin Heitmueller
2010-02-03 20:38 ` [PATCH 14/15] - zl10353 Stefan Ringel
2010-02-03 20:49 ` Devin Heitmueller
2010-02-03 21:07 ` Stefan Ringel
2010-02-04 2:43 ` Mauro Carvalho Chehab
2010-02-04 21:12 ` Stefan Ringel
2010-02-05 0:06 ` Mauro Carvalho Chehab
2010-02-03 20:40 ` [PATCH 15/15] - tm6000 hack with different demodulator parameter Stefan Ringel
2010-02-03 20:47 ` Devin Heitmueller
2010-02-03 20:16 ` [PATCH 1/15] - tm6000 build hunk Mauro Carvalho Chehab
2010-02-03 20:17 ` Devin Heitmueller
2010-02-03 21:48 ` Stefan Ringel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4B673B2D.6040507@arcor.de \
--to=stefan.ringel@arcor.de \
--cc=dheitmueller@kernellabs.com \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.