* [ath9k-devel] AR9220 AP mode 's throughput with ath9k @ 2011-06-02 7:07 kang haiyang 2011-06-02 7:22 ` Adrian Chadd 0 siblings, 1 reply; 5+ messages in thread From: kang haiyang @ 2011-06-02 7:07 UTC (permalink / raw) To: ath9k-devel hi all, Is there anyone who have evaluated ar9220's throughput with ath9k? With this card and ath9k, the average tx throughput is about 120Mbps. I thought with this card, it should be very easy to get 180Mbps (I can get this result with my 9160 card). With 20Mhz bandwith, under same environment, i can get more than 90Mbps' tx throughput. I have tested two cards from different vendors. And from packets captured, it shows that there are lots of CRC errors, and most of the packets are with MCS 12~15. Any idea? Is this ar9220's 40Mhz' limits, or ath9k doesn't support this card's full capability? BTW: I'm using 2.6.35 kernel, but with newer 2.6.38's compat-wireless driver, no big change. Best Regards, kang haiyang ^ permalink raw reply [flat|nested] 5+ messages in thread
* [ath9k-devel] AR9220 AP mode 's throughput with ath9k 2011-06-02 7:07 [ath9k-devel] AR9220 AP mode 's throughput with ath9k kang haiyang @ 2011-06-02 7:22 ` Adrian Chadd 2011-06-02 7:36 ` kang haiyang 0 siblings, 1 reply; 5+ messages in thread From: Adrian Chadd @ 2011-06-02 7:22 UTC (permalink / raw) To: ath9k-devel Hi! On 2 June 2011 15:07, kang haiyang <hykang@dongniannetworks.com> wrote: > hi all, > > Is there anyone who have evaluated ar9220's throughput with ath9k? > > With this card and ath9k, the average tx throughput is about 120Mbps. I > thought with this card, it should be very easy to get 180Mbps (I can get > this result with my 9160 card). How are you measuring this? > With 20Mhz bandwith, under same environment, i can get more than 90Mbps' > tx throughput. Again, how are you measuring it? > I have tested two cards from different vendors. And from packets > captured, it shows that there are lots of CRC errors, and most of the > packets are with MCS 12~15. Are you saying there's a lot of CRC errors on packets that you receive? Adrian ^ permalink raw reply [flat|nested] 5+ messages in thread
* [ath9k-devel] AR9220 AP mode 's throughput with ath9k 2011-06-02 7:22 ` Adrian Chadd @ 2011-06-02 7:36 ` kang haiyang 2011-06-02 7:53 ` kang haiyang 0 siblings, 1 reply; 5+ messages in thread From: kang haiyang @ 2011-06-02 7:36 UTC (permalink / raw) To: ath9k-devel hi, I measured them with Ixchariot (iperf is used also, almost same, but a little better). The distance between AP and client is about 1 meter, and i also tried with two different antennas. I captured the packet between the client and ap, and saw the packets from AP sent to client are with lots of CRC errors. The problem is that with the same method and environment, th 20Mhz is not so bad, and there should be no channel interference because there are no APs and clients observed on the channel we are working (channel 36). kang haiyang On 06/02/2011 03:22 PM, Adrian Chadd wrote: > Hi! > > On 2 June 2011 15:07, kang haiyang <hykang@dongniannetworks.com> wrote: >> hi all, >> >> Is there anyone who have evaluated ar9220's throughput with ath9k? >> >> With this card and ath9k, the average tx throughput is about 120Mbps. I >> thought with this card, it should be very easy to get 180Mbps (I can get >> this result with my 9160 card). > > How are you measuring this? > >> With 20Mhz bandwith, under same environment, i can get more than 90Mbps' >> tx throughput. > > Again, how are you measuring it? > >> I have tested two cards from different vendors. And from packets >> captured, it shows that there are lots of CRC errors, and most of the >> packets are with MCS 12~15. > > Are you saying there's a lot of CRC errors on packets that you receive? > > > > Adrian > ^ permalink raw reply [flat|nested] 5+ messages in thread
* [ath9k-devel] AR9220 AP mode 's throughput with ath9k 2011-06-02 7:36 ` kang haiyang @ 2011-06-02 7:53 ` kang haiyang 2011-06-03 4:54 ` kang haiyang 0 siblings, 1 reply; 5+ messages in thread From: kang haiyang @ 2011-06-02 7:53 UTC (permalink / raw) To: ath9k-devel One more thing, i'm using one dell's workstation and insert the minipci radio card to the machine with a minipci and pci converter. The converter should be OK, because 9160 card is all right. On 06/02/2011 03:36 PM, kang haiyang wrote: > hi, > > I measured them with Ixchariot (iperf is used also, almost same, but a > little better). The distance between AP and client is about 1 meter, and > i also tried with two different antennas. > > I captured the packet between the client and ap, and saw the packets > from AP sent to client are with lots of CRC errors. > > The problem is that with the same method and environment, th 20Mhz is > not so bad, and there should be no channel interference because there > are no APs and clients observed on the channel we are working (channel 36). > > kang haiyang > > On 06/02/2011 03:22 PM, Adrian Chadd wrote: >> Hi! >> >> On 2 June 2011 15:07, kang haiyang <hykang@dongniannetworks.com> wrote: >>> hi all, >>> >>> Is there anyone who have evaluated ar9220's throughput with ath9k? >>> >>> With this card and ath9k, the average tx throughput is about 120Mbps. I >>> thought with this card, it should be very easy to get 180Mbps (I can get >>> this result with my 9160 card). >> >> How are you measuring this? >> >>> With 20Mhz bandwith, under same environment, i can get more than 90Mbps' >>> tx throughput. >> >> Again, how are you measuring it? >> >>> I have tested two cards from different vendors. And from packets >>> captured, it shows that there are lots of CRC errors, and most of the >>> packets are with MCS 12~15. >> >> Are you saying there's a lot of CRC errors on packets that you receive? >> >> >> >> Adrian >> > _______________________________________________ > ath9k-devel mailing list > ath9k-devel at lists.ath9k.org > https://lists.ath9k.org/mailman/listinfo/ath9k-devel > ^ permalink raw reply [flat|nested] 5+ messages in thread
* [ath9k-devel] AR9220 AP mode 's throughput with ath9k 2011-06-02 7:53 ` kang haiyang @ 2011-06-03 4:54 ` kang haiyang 0 siblings, 0 replies; 5+ messages in thread From: kang haiyang @ 2011-06-03 4:54 UTC (permalink / raw) To: ath9k-devel I can get 180Mbps easily now with two 9220 cards using ath9k, one card is ap, another one is client. In Previous test, the client is using intel 5300 card, but seems that i need to re-test it. On 06/02/2011 03:53 PM, kang haiyang wrote: > One more thing, i'm using one dell's workstation and insert the minipci > radio card to the machine with a minipci and pci converter. The > converter should be OK, because 9160 card is all right. > > On 06/02/2011 03:36 PM, kang haiyang wrote: >> hi, >> >> I measured them with Ixchariot (iperf is used also, almost same, but a >> little better). The distance between AP and client is about 1 meter, and >> i also tried with two different antennas. >> >> I captured the packet between the client and ap, and saw the packets >> from AP sent to client are with lots of CRC errors. >> >> The problem is that with the same method and environment, th 20Mhz is >> not so bad, and there should be no channel interference because there >> are no APs and clients observed on the channel we are working (channel 36). >> >> kang haiyang >> >> On 06/02/2011 03:22 PM, Adrian Chadd wrote: >>> Hi! >>> >>> On 2 June 2011 15:07, kang haiyang <hykang@dongniannetworks.com> wrote: >>>> hi all, >>>> >>>> Is there anyone who have evaluated ar9220's throughput with ath9k? >>>> >>>> With this card and ath9k, the average tx throughput is about 120Mbps. I >>>> thought with this card, it should be very easy to get 180Mbps (I can get >>>> this result with my 9160 card). >>> >>> How are you measuring this? >>> >>>> With 20Mhz bandwith, under same environment, i can get more than 90Mbps' >>>> tx throughput. >>> >>> Again, how are you measuring it? >>> >>>> I have tested two cards from different vendors. And from packets >>>> captured, it shows that there are lots of CRC errors, and most of the >>>> packets are with MCS 12~15. >>> >>> Are you saying there's a lot of CRC errors on packets that you receive? >>> >>> >>> >>> Adrian >>> >> _______________________________________________ >> ath9k-devel mailing list >> ath9k-devel at lists.ath9k.org >> https://lists.ath9k.org/mailman/listinfo/ath9k-devel >> > _______________________________________________ > ath9k-devel mailing list > ath9k-devel at lists.ath9k.org > https://lists.ath9k.org/mailman/listinfo/ath9k-devel > ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2011-06-03 4:54 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2011-06-02 7:07 [ath9k-devel] AR9220 AP mode 's throughput with ath9k kang haiyang 2011-06-02 7:22 ` Adrian Chadd 2011-06-02 7:36 ` kang haiyang 2011-06-02 7:53 ` kang haiyang 2011-06-03 4:54 ` kang haiyang
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.